2014 Buick Regal Owners Manual

always set the parking brake and move the shift lever to P (Park). See Shifting Into Park on page 9-24.

Make sure the shift lever is fully in P (Park) before starting the engine. The vehicle has an automatic transmission shift lock control system. The regular brake must be fully applied first and then the shift lever button pressed before shifting from P (Park) when the ignition key

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (28,1)

9-28

Driving and Operating

is in ON/RUN. If you cannot shift out of P (Park), ease pressure on the shift lever, then push the shift lever all the way into P (Park) as you maintain brake application. Then press the shift lever button and move the shift lever into another gear. See Shifting out of Park (Automatic Transmission) on page 9-25.

Without the brake pedal applied, the control indicator will be on. If the shift lever is not in P (Park) when the ignition is turned to OFF, the control indicator and P will flash.

R (Reverse): Use this gear to back up.

{ Caution

Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped.

{ Warning

Shifting into a drive gear while the engine is running at high speed is dangerous. Unless your foot is firmly on the brake pedal, the vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while the engine is running at high speed.

To rock the vehicle back and forth to get out of snow, ice, or sand without damaging the transmission, see If the Vehicle Is Stuck on page 9-10. N (Neutral): In this position, the engine does not connect with the wheels. To restart the engine when the vehicle is already moving, use N (Neutral) only with the brake pedal applied.

{ Caution Shifting out of P (Park) or N (Neutral) with the engine running at high speed may damage the transmission. The repairs would not be covered by the vehicle warranty. Be sure the engine is not running at high speed when shifting the vehicle.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (29,1)

Manual Mode

Driver Shift Control (DSC)

{ Caution

Driving with the engine at a high rpm without upshifting while using Driver Shift Control (DSC), could damage the vehicle. Always upshift when necessary while using DSC.

D (Drive): This position is for normal driving. It provides the best fuel economy. If more power is needed for passing, and the vehicle is: . Going less than 56 km/h

(35 mph), push the accelerator pedal about halfway down.

. Going about 56 km/h (35 mph) or

more, push the accelerator all the way down.

{ Caution

If the vehicle accelerates slowly, or does not shift gears, the transmission could be damaged. Have the vehicle serviced right away.

Driving and Operating

9-29

DSC allows you to shift an automatic transmission similar to a manual transmission. To use the DSC feature: 1. Move the shift lever to the left

from D (Drive) into the side gate marked with (+) and (−).

2. Press the shift lever forward to

upshift or rearward to downshift.

While using the DSC feature, the vehicle will have firmer, quicker shifting. You can use this for sport driving or when climbing or descending hills, to stay in gear longer, or to downshift for more power or engine braking. The transmission will only allow you to shift into gears appropriate for the vehicle speed and engine revolutions per minute (rpm). The transmission will not automatically shift to the next lower gear if the engine rpm is too high, nor to the next higher gear when the maximum engine rpm is reached.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (30,1)

9-30

Driving and Operating

While in the DSC mode, the transmission will automatically downshift when the vehicle comes to a stop. This will allow for more power during take-off. When accelerating the vehicle from a stop in snowy and icy conditions, you may want to shift into second gear. A higher gear allows the vehicle to gain more traction on slippery surfaces. Vehicles with a turbocharged engine may also start in third gear.

Manual Transmission

{ Caution

Do not rest your foot on the clutch pedal while driving or while stopped. The pressure can cause premature wear in the clutch. The repairs would not be covered by the vehicle warranty.

1 (First): Press the clutch pedal fully to the pedal stop and shift into 1 (First). Then slowly let up on the clutch pedal as you press the accelerator pedal. If you come to a complete stop and it is hard to shift into 1 (First), put the shift lever in Neutral and let up on the clutch. Press the clutch pedal back down. Then shift into 1 (First). 2 (Second): Press the clutch pedal as you let up on the accelerator pedal and shift into 2 (Second). Then, slowly let up on the clutch pedal as you press the accelerator pedal.

This is the shift pattern for the 6-speed manual transmission. To operate the transmission:

{ Caution

Do not rest your hand on the shift lever while driving. The pressure could cause premature wear in the transmission. The repairs would not be covered by the vehicle warranty.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (31,1)

3 (Third), 4 (Fourth), 5 (Fifth), and 6 (Sixth): Shift into 3 (Third), 4 (Fourth), 5 (Fifth), and 6 (Sixth) the same way you do for 2 (Second). Slowly let up on the clutch pedal as you press the accelerator pedal. For the best fuel economy, use 6 (Sixth) gear whenever vehicle speed and driving conditions allow. The vehicle may have an up-shift light in the instrument cluster. See Up-Shift Light on page 5-26.

{ Warning If you skip a gear when downshifting, you could lose control of the vehicle. You could injure yourself or others. Do not shift down more than one gear at a time when downshifting.

{ Caution

Do not rest your foot on the clutch pedal while driving or while stopped. The pressure can cause premature wear in the clutch. The repairs would not be covered by the vehicle warranty.

To stop, let up on the accelerator pedal and press the brake pedal. Just before the vehicle stops, press the clutch pedal and the brake pedal, and shift to Neutral. Neutral: Use this position when you start or idle the engine. The shift lever is in Neutral when it is centered in the shift pattern, not in any gear. R (Reverse): To back up, with the vehicle at a complete stop, press down the clutch pedal. Then pull up on the button on the shift lever, and shift into R (Reverse). Let up on the clutch pedal slowly while pressing the accelerator pedal. If R (Reverse)

Driving and Operating

9-31

gear does not engage, shift the transmission to Neutral, release the clutch pedal, and press it back down. Repeat the gear selection.

{ Caution

Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped.

Use R (Reverse) along with the parking brake to park the vehicle. When operating, press the clutch pedal down completely. Do not use the pedal as a foot rest.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (32,1)

9-32

Driving and Operating

Some vehicles have a Driver Information Center (DIC) with an ECO Drive Assist Menu that contains a shift indicator. See Driver Information Center (DIC) (Base Level Cluster) on page 5-33 or Driver Information Center (DIC) (Uplevel Cluster) on page 5-35.

Drive Systems

Brakes

All-Wheel Drive If equipped, this feature transfers torque to the rear wheels as required. It is fully automatic, and adjusts itself as needed for road conditions. All-Wheel Drive (AWD) performance is automatically reduced when you use the compact spare. To restore full AWD performance, and prevent excessive wear to the clutch in the AWD system, replace the compact spare tire with a full-size tire as soon as possible. See Compact Spare Tire on page 10-76.

Antilock Brake System (ABS) This vehicle has ABS, an advanced electronic braking system that helps prevent a braking skid. When the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on, and it might even be noticed that the brake pedal moves a little. This is normal.

If there is a problem with ABS, this warning light stays on. See Antilock Brake System (ABS) Warning Light on page 5-25.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (33,1)

suddenly slows or stops. Always leave enough room up ahead to stop, even with ABS. Using ABS Do not pump the brakes. Just hold the brake pedal down firmly and let ABS work. You may hear the ABS pump or motor operating and feel the brake pedal pulsate. This is normal. Braking in Emergencies ABS allows you to steer and brake at the same time. In many emergencies, steering can help more than even the very best braking.

If driving safely on a wet road and it becomes necessary to slam on the brakes and continue braking to avoid a sudden obstacle, a computer senses the wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel. ABS can change the brake pressure to each wheel, as required, faster than any driver could. This can help you steer around the obstacle while braking hard. As the brakes are applied, the computer keeps receiving updates on wheel speed and controls braking pressure accordingly. Remember: ABS does not change the time needed to get a foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, there will not be enough time to apply the brakes if that vehicle

Driving and Operating

9-33

Parking Brake

The Electric Parking Brake (EPB) switch is on the center console. The EPB can always be activated, even if the ignition is off. To prevent draining the battery, avoid repeated cycles of the EPB when the engine is not running. The system has a red parking brake status light and an amber parking brake warning light. See Electric Parking Brake Light on page 5-24
and Service Electric Parking Brake Light on page 5-25. There are also

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (34,1)

9-34

Driving and Operating

parking brake-related Driver Information Center (DIC) messages. See Brake System Messages on page 5-39. In case of insufficient electrical power, the EPB cannot be applied or released. Before leaving the vehicle, check the red parking brake status light to ensure that the parking brake is applied. EPB Apply To apply the EPB: 1. Be sure the vehicle is at a

complete stop.

2. Lift up the EPB switch

momentarily.

The red parking brake status light will flash and then stay on once the EPB is fully applied. If the red parking brake status light flashes continuously, then the EPB is only partially applied or there is a problem with the EPB. A DIC message will display. Release the EPB and try to apply it again. If the light does not come on, or keeps

flashing, have the vehicle serviced. Do not drive the vehicle if the red parking brake status light is flashing. See your dealer. See Electric Parking Brake Light on page 5-24. If the amber parking brake warning light is on, lift up on the EPB switch and hold it up. Continue to hold the switch until the red parking brake status light remains on. If the amber parking brake warning light remains on, see your dealer. If the EPB is applied while the vehicle is moving, the vehicle will decelerate as long as the switch is held up. If the switch is held up until the vehicle comes to a stop, the EPB will remain applied. The vehicle may automatically apply the EPB in some situations when the vehicle is not moving. This is normal, and is done to periodically check the correct operation of the EPB system. If the EPB fails to apply, the rear wheels should be blocked to prevent vehicle movement.

EPB Release To release the EPB: 1. Place the ignition in the ACC/

ACCESSORY or ON/RUN position.

2. Apply and hold the brake pedal. 3. Push down momentarily on the

EPB switch.

The EPB is released when the red parking brake status light is off. If the amber parking brake warning light is on, release the EPB by pushing down on the EPB switch and holding it down. Continue to hold the switch until the red parking brake status light is off. If either light stays on after release is attempted, see your dealer.

{ Caution

Driving with the parking brake on can overheat the brake system and cause premature wear or

(Continued)

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (35,1)

Driving and Operating

9-35

Caution (Continued)

damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving.

Automatic EPB Release The EPB will automatically release if the vehicle is running, placed into gear, and an attempt is made to drive away. Avoid rapid acceleration when the EPB is applied, to preserve parking brake lining life. The EPB can also be used to prevent roll back for vehicles with a manual transmission taking off on a hill. When no roll back is desired, an applied EPB will allow both feet to be used for the clutch and accelerator pedals in preparation for starting the vehicle moving in the intended direction. In this case, there is no need to push the switch to release the EPB.

Brake Assist The Brake Assist feature is designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions. This feature uses the stability system hydraulic brake control module to supplement the power brake system under conditions where the driver has quickly and forcefully applied the brake pedal in an attempt to quickly stop or slow down the vehicle. The stability system hydraulic brake control module increases brake pressure at each corner of the vehicle until the ABS activates. Minor brake pedal pulsation or pedal movement during this time is normal and the driver should continue to apply the brake pedal as the driving situation dictates The Brake Assist feature will automatically disengage when the brake pedal is released or brake pedal pressure is quickly decreased.

Hill Start Assist (HSA) If equipped, Hill Start Assist (HSA) may be useful when the vehicle is stopped on a grade. This feature is designed to prevent the vehicle from rolling, either forward or rearward, during vehicle drive off. After the driver completely stops and holds the vehicle in a complete standstill on a grade, HSA will be automatically activated. During the transition period between when the driver releases the brake pedal and starts to accelerate to drive off on a grade, HSA holds the braking pressure to ensure that there is no rolling. The brakes will automatically release when the accelerator pedal is applied within the two-second window. It will not activate if the vehicle is in a drive gear and facing downhill or if the vehicle is facing uphill and in R (Reverse).

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (36,1)

9-36

Driving and Operating

Ride Control Systems

Traction Control/ Electronic Stability Control

System Operation The vehicle has a Traction Control System (TCS) and StabiliTrak®, an electronic stability control system. These systems help limit wheel slip and assist the driver in maintaining control, especially on slippery road conditions. TCS activates if it senses that any of the drive wheels are spinning or beginning to lose traction. When this happens, TCS applies the brakes to the spinning wheels and reduces engine power to limit wheel spin. StabiliTrak activates when the vehicle senses a difference between the intended path and the direction the vehicle is actually traveling. StabiliTrak selectively applies braking pressure to any one of the

vehicle wheel brakes to assist the driver in keeping the vehicle on the intended path. If cruise control is being used and traction control or StabiliTrak begins to limit wheel spin, cruise control will disengage. Cruise control may be turned back on when road conditions allow. Both systems come on automatically when the vehicle is started and begins to move. The systems may be heard or felt while they are operating or while performing diagnostic checks. This is normal and does not mean there is a problem with the vehicle. It is recommended to leave both systems on for normal driving conditions, but it may be necessary to turn TCS off if the vehicle gets stuck in sand, mud, ice, or snow. See If the Vehicle Is Stuck on page 9-10 and “Turning the Systems Off and On” later in this section.

The indicator light for both systems is in the instrument cluster. This light will:

Flash when TCS is limiting wheel spin. Flash when StabiliTrak is activated. Turn on and stay on when either system is not working.

If either system fails to turn on or to activate, a message displays in the Driver Information Center (DIC), and d comes on and stays on to indicate that the system is inactive and is not assisting the driver in maintaining control. The vehicle is safe to drive, but driving should be adjusted accordingly.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (37,1)

If d comes on and stays on: 1. Stop the vehicle. 2. Turn the engine off and wait

15 seconds.

3. Start the engine. Drive the vehicle. If d comes on and stays on, the vehicle may need more time to diagnose the problem. If the condition persists, see your dealer. Turning the Systems Off and On

To turn the system off, press the TCS/StabiliTrak button on the center stack.

{ Caution

Do not repeatedly brake or accelerate heavily when TCS is off. The vehicle driveline could be damaged.

To turn off only TCS, press and release the TCS/StabiliTrak g button. The traction off light i displays in the instrument cluster. The appropriate message displays in the DIC. See Ride Control System Messages on page 5-45. To turn TCS on again, press and release the TCS/StabiliTrak g button. The traction off light i displayed in the instrument cluster will turn off. If TCS is limiting wheel spin when the TCS/StabiliTrak button is pressed, the system will not turn off until the wheels stop spinning.

Driving and Operating

9-37

To turn off both TCS and StabiliTrak, press and hold the TCS/StabiliTrak g button until the traction off light i and StabiliTrak OFF Light g come on and stay on in the instrument cluster. The appropriate message displays in the DIC. See Ride Control System Messages on page 5-45. To turn TCS and StabiliTrak on again, press and release the TCS/ StabiliTrak button. The traction off light i and StabiliTrak OFF Light g in the instrument cluster turn off. Adding accessories can affect the vehicle performance. See Accessories and Modifications on page 10-3.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (38,1)

. Power steering assistance is

normal. GS Mode . Additional stiffness in the shock

absorbers for increased body control. The powertrain reacts more quickly to the accelerator pedal.

. Power steering assistance is

reduced.

9-38

Driving and Operating

Selective Ride Control The vehicle may have Selective Ride Control. The SPORT and GS buttons are on top of the center stack. Selective Ride Control adapts to the preference of the driver within one of three driving modes: Standard: Default mode used for normal and long-distance highway driving. This setting provides a smooth soft ride. Sport: Use for normal city and long-distance highway driving. This setting provides precise, comfortable handling. Press and release the SPORT button on top of the center stack and the light on the button comes on. Press the button again and the system returns to the Standard mode. GS: Use where personal preference or road conditions demand more control. This setting provides responsive, controlled steering and handling and also modifies the All-Wheel Drive (AWD). Press and release the GS button on

top of the center stack. The light on the button comes on, and the appropriate message displays on the DIC. Press the button again. The system returns to the Standard mode and the appropriate message displays on the DIC. Selective Ride Control automatically comes on in the Standard mode when the vehicle is started. When the Sport and GS modes are turned off, the system returns to the Standard mode. Standard Mode

The powertrain reacts normally to the accelerator pedal.

. Power steering assistance is

normal.

Sport Mode

The shock absorbers stiffen to provide better contact with the road surface. The powertrain reacts normally to the accelerator pedal.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (39,1)

Cruise Control With cruise control the vehicle can maintain a speed of about 40 km/h (25 mph) or more without keeping your foot on the accelerator. Cruise control does not work at speeds below 40 km/h (25 mph). { Warning

Cruise control can be dangerous where you cannot drive safely at a steady speed. Do not use the cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads.

If equipped with the Traction Control System (TCS), the system may begin to limit wheel spin while you are using cruise control. If this

happens, the cruise control will automatically disengage. See Traction Control/Electronic Stability Control on page 9-36. If a collision alert occurs when cruise control is activated, cruise control is disengaged. See Forward Collision Alert (FCA) System on page 9-52. When road conditions allow you to safely use it again, the cruise control can be turned back on. If the brakes are applied, the cruise control disengages.

Driving and Operating

9-39

5 (On/Off): Press to turn cruise control on or off. A white indicator comes on in the instrument cluster. RES/+ (Resume/Accelerate): Press the control up briefly to make the vehicle resume to a previously set speed, or hold upwards to accelerate. If cruise control is already active, use to increase vehicle speed. SET/− (Set/Coast): Press the control down briefly to set the speed and activate cruise control. If cruise control is already active, use to decrease vehicle speed. * (Cancel): Press to disengage cruise control without erasing the selected set speed.

Setting Cruise Control If the cruise button is on when not in use, it could get bumped and go into cruise when not desired. Keep the cruise control switch off when cruise is not being used.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (40,1)

9-40

Driving and Operating

1. Press the 5 button to turn the

cruise system on.

2. Get to the speed desired. 3. Press and release the SET/−

control on the steering wheel . The desired set speed briefly appears in the instrument panel cluster.

4. Remove foot from the

accelerator.

The cruise control indicator on the instrument cluster turns green after cruise control has been set to the desired speed. See Instrument Cluster (Base Cluster) on page 5-9
or Instrument Cluster (Uplevel Cluster) on page 5-13.

Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied or the * is pressed, the cruise control is disengaged without erasing the set speed from memory.

Once the vehicle reaches about 40 km/h (25 mph) or more, press RES/+ up briefly. The vehicle returns to the previous set speed.

Increasing Speed While Using Cruise Control If the cruise control system is already activated: . Press and hold RES/+ up until the vehicle accelerates to the desired speed, then release it. To increase the speed in small increments, press RES/+ up briefly. Each time this is done, the vehicle goes about 1.6 km/h (1 mph) faster.

Reducing Speed While Using Cruise Control If the cruise control system is already activated: . Press and hold SET/− down until

the desired lower speed is reached, then release it.

To slow down in small increments, press SET/− down briefly. Each time this is done, the vehicle goes about 1.6 km/h (1 mph) slower.

Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase vehicle speed. When you take your foot off the pedal, the vehicle will slow down to the cruise speed you set earlier. While pressing the accelerator pedal or shortly following the release to override cruise control, briefly pressing SET− will result in cruise set to the current vehicle speed.

Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain your speed. When going downhill, you might have to brake or shift to a

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (41,1)

lower gear to keep your speed down. If the brakes are applied the cruise control will disengage.

Ending Cruise Control There are three ways to end cruise control:

To disengage cruise control, step lightly on the brake pedal or clutch.

. Press * on the steering wheel.

To turn off the cruise control, press 5 on the steering wheel.

Erasing Speed Memory The cruise control set speed is erased from memory by pressing 5
or if the ignition is turned off.

Adaptive Cruise Control If equipped with Adaptive Cruise Control (ACC), it allows the driver to select the cruise control set speed and following gap. Read this entire section before using this system. The following gap is the following

Driving and Operating

9-41

time between your vehicle and a vehicle detected directly ahead in your path, moving in the same direction. If no vehicle is detected in your path, ACC works like regular cruise control. ACC uses a radar sensor . See Radio Frequency Statement on page 13-15. If a vehicle is detected in your path, ACC can apply acceleration or limited, moderate braking to maintain the selected following gap. To disengage ACC, apply the brake. If ACC is controlling your vehicle speed when the traction control system (TCS) or electronic stability control system activates, the ACC may automatically disengage. See Traction Control/Electronic Stability Control on page 9-36. When road conditions allow ACC to be safely used, the ACC can be turned back on. ACC will not engage if the TCS or electronic stability control system is disabled.

{ Warning

ACC has limited braking ability and may not have time to slow the vehicle down enough to avoid a collision with another vehicle you are following. This can occur when vehicles suddenly slow or stop ahead, or enter your lane. Also see “Alerting the Driver” in this section. Complete attention is always required while driving and you should be ready to take action and apply the brakes. See Defensive Driving on page 9-3.

{ Warning

Adaptive Cruise Control will not detect or brake for children, pedestrians, animals, or other objects.

(Continued)

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (42,1)

9-42

Driving and Operating

Warning (Continued)

Do not use Adaptive Cruise Control when:

. On winding and hilly roads or

when the sensors are blocked by snow, ice, or dirt. The system may not detect a vehicle ahead. Keep the entire front of the vehicle clean.

. Visibility is low, such as in

fog, rain, or snow conditions. Adaptive Cruise Control performance is limited under these conditions.

. On slippery roads where fast

changes in tire traction can cause excessive wheel slip.

] (On/Off): Press to turn the system on or off. The indicator turns white on the instrument cluster when ACC is turned on. +RES (Resume/Accelerate): Press the control up briefly to make the vehicle resume to a previously set speed, or hold upwards to accelerate. If cruise control is already active, use to increase vehicle speed.

SET– (Set/Coast): Press the control down briefly to set the speed and activate ACC. If cruise control is already active, use to decrease vehicle speed. * (Cancel): Press to disengage ACC without erasing the selected set speed. 3 (Follow Distance Gap): Press to select a following gap time (or distance) setting for ACC of Far, Medium, or Near.

Setting Adaptive Cruise Control If the cruise button is on when not in use, it could get pressed and go into cruise when not desired. Keep the cruise control button off when cruise is not being used. Select the set speed desired for cruise. This is the vehicle speed when no vehicle is detected in its path. ACC will not set at a speed less than 25 km/h (16 mph), although it can be resumed when driving at lower speeds.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (43,1)

Driving and Operating

9-43

To set ACC:

1. Press ].

2. Get up to the desired speed. 3. Press and release the SET–

control on the steering wheel.

4. Remove foot from the

accelerator.

After ACC is set, it may immediately apply the brakes if a vehicle ahead is detected closer than the selected following gap.

The ACC indicator displays on the instrument cluster. When ACC is active, the indicator turns green. Be mindful of speed limits, surrounding traffic speeds, and weather conditions when selecting the set speed.

Resuming a Set Speed If the ACC is set at a desired speed and then the brakes are applied, ACC is disengaged without erasing the set speed from memory. To begin using ACC again, press +RES up briefly on the steering wheel. The vehicle returns to the previous set speed.

Increasing Speed While ACC is at a Set Speed If ACC is already activated, do one of the following: . Use the accelerator to get to the higher speed. Press SET– down. Release the control and the accelerator pedal. The vehicle will now cruise at the higher speed. When the accelerator pedal is pressed, ACC will not brake because it is overridden. A warning message will appear on the Driver Information Center (DIC). See Cruise Control Messages on page 5-40.

. Press and hold +RES up until the desired set speed appears on the display, then release it. To increase vehicle speed in small increments, briefly press +RES. For each press, the vehicle goes to the next 5 km/h (1 mph) faster mark on the speedometer.

When it is determined that there is no vehicle ahead or the vehicle ahead is beyond the selected following gap, then the vehicle speed will increase to the set speed. The speedometer reading can be displayed in either English or metric units. See Instrument Cluster (Base Cluster) on page 5-9 or Instrument Cluster (Uplevel Cluster) on page 5-13. The increment value used depends on the units displayed.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (44,1)

9-44

Driving and Operating

Reducing Speed While ACC is at a Set Speed If ACC is already activated, do one of the following: . Use the brake to get to the desired lower speed. Press SET– down and release the accelerator pedal. The vehicle will now cruise at the lower speed.

. Press and hold SET– down until

the desired lower speed is reached, then release it. To decrease the vehicle speed in small increments, briefly press SET−. For each press, the vehicle goes to the next 5 km/h (1 mph) slower mark on the speedometer.

The speedometer reading can be displayed in either English or metric units. See Instrument Cluster (Base Cluster) on page 5-9 or Instrument Cluster (Uplevel Cluster) on page 5-13. The increment value used depends on the units displayed.

Selecting the Follow Distance Gap When a slower moving vehicle is detected ahead within the selected following gap, ACC will adjust the vehicle's speed and attempt to maintain the follow distance gap selected. Press 3 on the steering wheel to adjust the following gap. When pressed, the current gap setting displays briefly on the instrument cluster. Subsequent presses cycle the gap button through three settings: Far, Medium, or Near. Since each gap setting corresponds to a following time (Far, Medium, or Near), the following distance will vary based on vehicle speed. The

faster the vehicle speed, the further back your vehicle will follow a vehicle detected ahead. Consider traffic and weather conditions when selecting the following gap. The range of selectable gaps may not be appropriate for all drivers and driving conditions. Changing the gap setting automatically changes the alert timing sensitivity (Far, Medium, or Near) for the Forward Collision Alert (FCA) feature. See Forward Collision Alert (FCA) System on page 9-52.

Alerting the Driver

If ACC is engaged, driver action may be required when ACC cannot apply sufficient braking because of approaching a vehicle too rapidly.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (45,1)

When this condition occurs, the collision alert will display on the instrument cluster and eight beeps will sound from the front. See Defensive Driving on page 9-3.

Approaching and Following a Vehicle

The vehicle ahead symbol is in the instrument cluster. The vehicle ahead symbol only displays when a vehicle is detected in your vehicle’s path moving in the same direction. If this symbol is not displaying, ACC will not respond to or brake to vehicles ahead. ACC automatically slows the vehicle down and adjusts vehicle speed to follow the vehicle in front at the

Driving and Operating

9-45

selected follow gap. The vehicle speed increases or decreases to follow the vehicle in front of you, but will not exceed the set speed. It may apply limited braking, if necessary. When braking is active, the brake lights will come on. The automatic braking may feel or sound different than if the brakes were applied manually. This is normal.

Stationary or Very Slow-Moving Objects

{ Warning

Adaptive Cruise Control (ACC) may not detect and react to stopped or slow-moving vehicles ahead of you. For example, the system may not brake for a vehicle that it has never detected moving. This can occur in stop-and-go traffic or when a vehicle suddenly appears due to a vehicle ahead changing lanes. Your vehicle may not stop and

(Continued)

Warning (Continued)

could cause a crash. Use caution when using ACC. Your complete attention is always required while driving and you should be ready to take action and apply the brakes.

ACC Automatically Disengages ACC may automatically disengage and the driver will need to manually apply the brakes to slow the vehicle when:

The sensors are blocked. The traction control system (TCS) or electronic stability control system has activated or been disabled.

. No traffic or other objects are

being detected. There is a fault in the system.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (46,1)

9-46

Driving and Operating

hold the vehicle. The electric parking brake status light will turn on. See Parking Brake on page 9-33. To resume ACC and release the electric parking brake, press the accelerator pedal. A DIC warning message may display indicating to shift to P (Park) before exiting the vehicle. See Vehicle Messages on page 5-39.

{ Warning

If ACC has stopped the vehicle, and if ACC is disengaged, turned off, or canceled, the vehicle will no longer be held at a stop. The vehicle can move. When ACC is holding the vehicle at a stop, always be prepared to manually apply the brakes.

{ Warning

Leaving the vehicle without placing it in P (Park) can be dangerous. Do not leave the vehicle while it is being held at a stop by ACC. Always place the vehicle in P (Park) and turn off the ignition before leaving the vehicle.

ACC Override If using the accelerator pedal while ACC is active, a warning message on the DIC will indicate that automatic braking will not occur. See Vehicle Messages on page 5-39. ACC will resume operation when the accelerator pedal is not being pressed.

A message indicating that cruise is disengaging will appear on the DIC and the ACC active symbol will not be displayed when ACC is no longer active.

Notification to Resume ACC ACC will maintain a follow gap behind a detected vehicle and slow your vehicle to a stop behind that vehicle. If the stopped vehicle ahead has driven away and ACC has not resumed, the vehicle ahead symbol will flash as a reminder to check traffic ahead before proceeding. In addition, three beeps will sound. See “Go Notifier” in “Collision/ Detection Systems” under Vehicle Personalization on page 5-48. When the vehicle ahead drives away, press RES+ or the accelerator pedal to resume cruise control. If stopped for more than two minutes or if the driver door is opened and the driver safety belt is unbuckled, the ACC automatically applies the electric parking brake to

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (47,1)

{ Warning

{ Warning

On curves, ACC may respond to a vehicle in another lane, or may not have time to react to a vehicle in your lane. You could crash into a vehicle ahead of you, or lose control of your vehicle. Give extra attention in curves and be ready to use the brakes if necessary. Select an appropriate speed while driving in curves.

ACC may operate differently in a sharp curve. It may reduce the vehicle speed if the curve is too sharp.

The ACC will not automatically apply the brakes if your foot is resting on the accelerator pedal. You could crash into a vehicle ahead of you.

Curves in the Road

{ Warning

On curves, ACC may not detect a vehicle ahead in your lane. You could be startled if the vehicle accelerates up to the set speed, especially when following a vehicle exiting or entering exit ramps. You could lose control of the vehicle or crash. Do not use ACC while driving on an entrance or exit ramp. Always be ready to use the brakes if necessary.

Driving and Operating

9-47

When following a vehicle and entering a curve, ACC may not detect the vehicle ahead and accelerate to the set speed. When this happens, the vehicle ahead symbol will not appear.

ACC may detect a vehicle that is not in your lane and apply the brakes. ACC may occasionally provide an alert and/or braking that is considered unnecessary. It could respond to vehicles in different lanes, signs, guardrails, and other stationary objects when entering or exiting a curve. This is normal operation. The vehicle does not need service.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (48,1)

9-48

Driving and Operating

Cleaning the Sensing System The radar sensor on the front of the vehicle can become blocked by snow, ice, dirt, or mud. This area needs to be cleaned for ACC to operate properly. For cleaning instructions, see “Washing the Vehicle” under Exterior Care on page 10-86. System operation may also be limited under snow, heavy rain, or road spray conditions.

Other Vehicle Lane Changes

ACC will not detect a vehicle ahead until it is completely in the lane. The brakes may need to be manually applied.

Do Not Use ACC on Hills and When Towing a Trailer

Do not use ACC when driving on steep hills or when towing a trailer. ACC will not detect a vehicle in the lane while driving on steep hills. The driver will often need to take over acceleration and braking on steep hills, especially when towing a trailer. If the brakes are applied, the ACC disengages.

Disengaging ACC There are three ways to disengage ACC: . Step lightly on the brake pedal. . Press *.

. Press ].

Erasing Speed Memory The cruise control set speed is erased from memory if ] is pressed or if the ignition is turned off.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (49,1)

Driver Assistance Systems This vehicle may have features that work together to help avoid crashes or reduce crash damage while driving, backing, and parking. Read this entire section before using these systems.

{ Warning Do not rely on the Driver Assistance Systems. These systems do not replace the need for paying attention and driving safely. You may not hear or see alerts or warnings provided by these systems. Failure to use proper care when driving may result in injury, death, or vehicle damage. See Defensive Driving on page 9-3. Under many conditions, these systems will not:

(Continued)

Warning (Continued)

. Detect children, pedestrians,

bicyclists, or animals.

. Detect vehicles or objects

outside the area monitored by the system.

. Work at all driving speeds. . Warn you or provide you with enough time to avoid a crash.

. Work under poor visibility or

bad weather conditions.

. Work if the detection sensor is not cleaned or is covered by ice, snow, mud, or dirt. Complete attention is always required while driving, and you should be ready to take action and apply the brakes and/or steer the vehicle to avoid crashes.

Driving and Operating

9-49

Assistance Systems for Parking or Backing When the vehicle is in R (Reverse), the Rear Vision Camera (RVC), Rear Parking Assist, and Rear Cross Traffic Alert (RCTA), if equipped, may help the driver to avoid a crash or to reduce crash damage. Some models may also have Front Parking Assist. When the vehicle is shifted into R (Reverse), the RVC displays an image of the area behind the vehicle in the center stack display. { Warning

The RVC system does not display children, pedestrians, bicyclists, animals, or any other object located outside the camera's field of view, below the bumper, or under the vehicle. Perceived distances may be different from actual distances. Do not back the (Continued)

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (50,1)

9-50

Driving and Operating

Warning (Continued)

vehicle using only the RVC screen, during longer, higher speed backing maneuvers, or where there could be cross traffic. Failure to use proper care before backing may result in injury, death, or vehicle damage. Always check behind and around the vehicle before backing.

1. View Displayed by the Camera

1. View Displayed by the Camera 2. Corners of the Rear Bumper Displayed images may be farther or closer than they appear. The area displayed is limited and objects that are close to either corner of the bumper or under the bumper do not display. A warning triangle may display on the RVC screen to show where the Ultrasonic Rear Parking Assist (URPA) has detected an object. This triangle changes from amber to red and increases in size the closer the object. On vehicles with the Rear Cross Traffic Alert (RCTA), a red warning triangle with an arrow may also

display on the RVC screen to warn of traffic coming from either direction. This system detects objects coming from up to 20 m (65 ft) from the left or right side of the vehicle. When an object is detected, three beeps sound from the left or right side, depending on the direction of the detected vehicle. With URPA, as the vehicle backs up at speeds of less than 8 km/h (5 mph), the system detects objects up to 2.5 m (8 ft) behind the vehicle that are within a zone 25 cm (10 in) high off the ground and below bumper level. If the vehicle has the Front Parking Assist, it also detects objects 1.2 m (4 ft) in front of the vehicle. These detection distances may be less during warmer or humid weather.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (51,1)

Driving and Operating

9-51

{ Warning

The parking assist system does not detect children, pedestrians, bicyclists, animals, or objects located below the bumper or that are too close or too far from the vehicle. It is not available at speeds greater than 8 km/h (5 mph). To prevent injury, death, or vehicle damage, even with parking assist, always check the area around the vehicle and check all mirrors before moving forward or backing.

The instrument cluster may have a parking assist display with bars that show “distance to object” and object location information for URPA, and on some vehicles, for the Front Parking Assist system. As the object gets closer, more bars light up. When an object is first detected in the rear, one beep will be heard from the rear. When an object is very close (<0.6 m (2 ft) in the vehicle rear, or <0.3 m (1 ft) in the vehicle front), five beeps will sound from the rear or front depending on object location. Beeps for Front Parking Assist are higher pitched than for Rear Parking Assist.

Turning the Features On or Off

The X button on the center stack is used to turn on or off Parking Assist. The indicator light next to the button comes on when the features are on and turns off when the features have been disabled. The RVC, the RCTA system, parking assist symbols, and guidance lines can be turned on or off through the infotainment system: 1. On the infotainment system,

press the Settings screen button, or turn the MENU knob to highlight Settings and press MENU.

2. Select Rear Camera.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (52,1)

9-52

Driving and Operating

3. Press Rear Camera Display (if equipped), Rear Cross Traffic Alert, Park Assist Symbols, or Guidance Lines and then select OFF or ON.

Assistance Systems for Driving If equipped, when driving the vehicle forward, Forward Collision Alert (FCA), Lane Departure Warning (LDW), Side Blind Zone Alert (SBZA), Lane Change Alert (LCA), and/or the Active Emergency Braking System can help to avoid a crash or reduce crash damage.

Forward Collision Alert (FCA) System The Forward Collision Alert (FCA) system may help to avoid or reduce the harm caused by front-end crashes. FCA provides a visual alert and beeps when approaching a vehicle directly ahead too quickly.

The forward-looking FCA camera sensor is on the windshield ahead of the rearview mirror. FCA detects vehicles within a distance of approximately 60 m (197 ft) and operates at speeds above 40 km/h (25 mph). If the vehicle has Adaptive Cruise Control (ACC), it can detect vehicles to distances of approximately 110 m (360 ft) and operates at all speeds. See Adaptive Cruise Control on page 9-41.

{ Warning

FCA is a warning system and does not apply the brakes. When approaching a slower-moving or stopped vehicle ahead too rapidly, or when following a vehicle too closely, FCA may not provide a warning with enough time to help avoid a crash. FCA does not warn of pedestrians, animals, signs, guardrails, bridges, construction

(Continued)

Warning (Continued)

barrels, or other objects. Be ready to take action and apply the brakes. For more information, see Defensive Driving on page 9-3.

Detecting the Vehicle Ahead

FCA warnings will not occur unless the FCA system detects a vehicle ahead. The vehicle ahead indicator will display green when a vehicle is detected in front. Vehicles may not be detected on curves, highway exit ramps, or hills; or due to poor visibility. FCA will not detect another vehicle ahead until it is completely in the driving lane.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (53,1)

{ Warning

FCA does not provide a warning to help avoid a crash, unless it detects a vehicle. FCA may not detect a vehicle ahead if the FCA sensor is blocked by dirt, snow, or ice, or if the windshield is damaged. It may also not detect a vehicle on winding or hilly roads, or in conditions that can limit visibility such as fog, rain, or snow, or if the headlamps or windshield are not cleaned or in proper condition. Keep the windshield, headlamps, and FCA sensors clean and in good repair.

Collision Alert

When your vehicle approaches another vehicle too rapidly, the FCA display will come on and several beeps will sound from the front. When this occurs, the brake system prepares for driver braking to occur more rapidly, if needed. Selecting the Alert Timing

The Collision Alert control is on the steering wheel. Press 3 to set the alert timing. The first button press shows the current control setting on

Driving and Operating

9-53

the DIC. Additional button presses will change this setting and turn the system off. Unnecessary Alerts FCA may provide unnecessary alerts to turning vehicles, vehicles in other lanes, objects that are not vehicles, or shadows. These alerts are normal operation and the vehicle does not need service. Other Messages There are messages that may appear on the Driver Information Center (DIC) in the instrument cluster to provide information about FCA. See Object Detection System Messages on page 5-43. Cleaning the System If the FCA system does not seem to operate properly, clean the outside of the windshield area in front of the camera sensor before considering taking the vehicle in for service.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (54,1)

9-54

Driving and Operating

Active Emergency Braking System If the vehicle has Adaptive Cruise Control (ACC) it also has the Active Emergency Braking System, which includes Intelligent Brake Assist (IBA) and the Automatic Collision Preparation (ACP) System. These systems can provide a boost to braking or automatically brake the vehicle to help avoid or lessen the severity of crashes. Intelligent Brake Assist (IBA) IBA may activate when the brake pedal is applied quickly by providing a boost to braking based on the speed of approach and distance to a vehicle ahead. Minor brake pedal pulsations or pedal movement during this time is normal and the brake pedal should continue to be applied as needed. IBA will automatically disengage only when the brake pedal is released

{ Warning

{ Warning

IBA may increase vehicle braking in situations when it may not be necessary. You could block the flow of traffic. If this occurs, take your foot off the brake pedal and then apply the brakes as needed.

ACP is an emergency crash preparation feature and is not designed to avoid crashes. Do not rely on ACP to brake the vehicle. ACP may not:

Automatic Collision Preparation (ACP) System ACP may help reduce crash damage by applying the vehicle’s brake system and has a detection range of approximately 60 m (197 ft). Braking can only occur if a vehicle is detected ahead. This is shown by the FCA vehicle-ahead indicator being lit. See Forward Collision Alert (FCA) System on page 9-52.

. Respond to stopped vehicles,

pedestrians, or animals.

. Detect a vehicle ahead on

winding or hilly roads.

. Detect a stopped or

slow-moving vehicle or other object ahead.

. Detect a vehicle when

weather limits visibility, such as in fog, rain, or snow. In these situations, ACP sensor performance is limited.

(Continued)

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (55,1)

Driving and Operating

9-55

Warning (Continued)

Complete attention is always required while driving, and you should be ready to take action and apply the brakes and/or steer the vehicle to avoid crashes.

Brake Preparation When quickly approaching a vehicle ahead, Brake Preparation reduces brake response time by having the brake system prepared for driver braking to occur more rapidly.

Automatic Braking In some imminent front-end crash situations, if the driver has not applied the brakes, Automatic Braking applies the brakes to help reduce crash damage. It may even help avoid some very low speed crashes. Automatic Braking may slow the vehicle to a complete stop to try to avoid a potential crash. The vehicle

will only hold at a stop briefly. A firm press of the accelerator pedal will also release Automatic Braking.

{ Warning Automatic Braking may automatically brake the vehicle in situations where it may be unnecessary. It could respond to a turning vehicle ahead, guardrails, signs, and other non-moving objects. This could be uncomfortable and startling. To override Automatic Braking, firmly press the accelerator pedal, if it is safe to do so.

Automatic Braking can be disabled or reduced through vehicle personalization. See the “Auto Collision Preparation” portion of “Collision/Detection Systems” under Vehicle Personalization on page 5-48.

{ Warning

Using the Automatic Collision Preparation System while towing a trailer could cause you to lose control of the vehicle and crash. Turn the system off when towing a trailer.

Side Blind Zone Alert (SBZA) If equipped, the SBZA system is a lane-changing aid that assists drivers with avoiding crashes that occur with vehicles in the side blind zone (or spot) areas. When the vehicle is moving forward, the left- or right-side mirror display will light up if a vehicle is detected in that blind zone. If the turn signal is activated and a vehicle is also detected on the same side, the display will flash as an extra warning not to change lanes. Since this system is part of the Lane

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (56,1)

Warning (Continued)

changing lanes may result in injury, death, or vehicle damage. Before making a lane change, always check mirrors, glance over your shoulder, and use the turn signals.

9-56

Driving and Operating

Change Alert system, please read the entire Lane Change Alert section before using this feature.

Lane Change Alert If equipped, the Lane Change Alert (LCA) system is a lane-changing aid that assists drivers with avoiding lane change crashes that occur with vehicles in the side blind zone (or spot) areas or with vehicles rapidly approaching these areas from behind. The LCA warning display will light up in the corresponding outside side mirror and will flash if the turn signal is on.

{ Warning

LCA does not alert the driver to vehicles outside of the system detection zones, pedestrians, bicyclists, or animals. It may not provide alerts when changing lanes under all driving conditions. Failure to use proper care when

(Continued)

1. SBZA Detection Zone 2. LCA Detection Zone

LCA Detection Zones The LCA sensor covers a zone of approximately one lane over from both sides of the vehicle, or 3.5 m (11 ft). The height of the zone is

approximately between 0.5 m (1.5 ft) and 2 m (6 ft) off the ground. The side blind zone warning area starts at approximately the middle of the vehicle and goes back 5 m (16 ft). Drivers are also warned of vehicles rapidly approaching from up to 70 m (230 ft) behind the vehicle. How the System Works The LCA symbol lights up in the side mirrors when the system detects a vehicle in the next lane over that is in the side blind zone or rapidly approaching from behind. A lit LCA symbol indicates it may be unsafe to change lanes. Before making a lane change, check the LCA display, check mirrors, glance over your shoulder, and use the turn signals.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (57,1)

Left Side Mirror

Right Side Mirror

Display

Display

When the vehicle is started, both outside mirror LCA displays will briefly come on to indicate the system is operating. When the vehicle is moving forward, the left- or right-side mirror display will light up if a vehicle is detected in the next lane over in that blind zone or rapidly approaching that zone. If the turn signal is activated in the same direction as a detected vehicle, this display will flash as an extra warning not to change lanes.

Driving and Operating

9-57

LCA can be disabled through vehicle personalization. See “Collision/Detection Systems” under Vehicle Personalization on page 5-48. If LCA is disabled by the driver, the LCA mirror displays will not light up. When the System Does Not Seem to Work Properly The LCA system requires some driving for the system to calibrate to maximum performance. This calibration may occur more quickly if the vehicle is driving on a straight highway road with traffic and roadside objects (e.g., guardrails, barriers). LCA displays may not come on when passing a vehicle quickly. LCA may alert to objects attached to the vehicle, such as a trailer, bicycle, or object extending out to either side of the vehicle. Attached objects may also interfere with the detection of vehicles. This is normal system operation; the vehicle does not need service.

LCA may not always alert the driver to vehicles in the next lane over, especially in wet conditions or when driving on sharp curves. The system does not need to be serviced. The system may light up due to guardrails, signs, trees, shrubs, and other non-moving objects. This is normal system operation; the vehicle does not need service. LCA may not operate when the LCA sensors in the left or right corners of the rear bumper are covered with mud, dirt, snow, ice, or slush, or in heavy rainstorms. For cleaning instructions, see "Washing the Vehicle" under Exterior Care on page 10-86. If the DIC still displays the system unavailable message after cleaning both sides of the vehicle toward the rear corners of the vehicle, see your dealer. If the LCA displays do not light up when vehicles are in the side blind zone or rapidly approaching this zone and the system is clean, the system may need service. Take the vehicle to your dealer.

Buick Regal Owner Manual 6081497) - 2014 - CRC 2nd Edition - 11/22/13

(GMNA-Localizing-U.S./Canada/Mexico-

Black plate (58,1)

9-58

Driving and Operating

When LCA is disabled for any reason other than the driver turning it off, the Side Blind Zone Alert On option will not be available on the personalization menu. FCC Information See Radio Frequency Statement on page 13-15.

Lane Departure Warning (LDW) If equipped, LDW may help avoid crashes due to unintentional lane departures. It may provide a warning if the vehicle is crossing a detected lane without using a turn signal in the lane departure direction. LDW uses a camera sensor to detect the lane markings. It only operates at speeds of 56 km/h (35 mph) or greater. When the vehicle crosses a detected lane marking, the LDW indicator will flash and three beeps will be sounded from the left or right side, depending on the lane

departure direction. LDW will not warn if the turn signal is on in the departure direction, or if a sharp maneuver is made.

{ Warning

The LDW system is an aid to help the vehicle stay in the driving lane. It does not steer the vehicle.