Instrument Panel Indicators
Charging System Indicator
If this indicator comes on when the engine is running, the battery is not being charged, and you will also see a ‘‘CHECK CHARGING SYSTEM’’ message on the multi-information display. For more information, see page
470
Immobilizer System Indicator
This indicator comes on briefly when you turn the ignition switch to the ON (II) position. It will then go off if you have inserted a properly-coded ignition key. If it is not a properly- coded key, the indicator will blink, and the engine’s fuel system will be disabled (see page
).
121
U.S.
Canada
Parking Brake and Brake System Indicator
This indicator has two functions:
1.
It comes on when you turn the ignition switch to the ON (II) position. It is a reminder to check the parking brake. Driving with the parking brake not fully released can damage the rear brakes, axles, and tires.
If you drive without releasing the parking brake, a beeper will sound, and you will also see a ‘‘RELEASE PARKING BRAKE’’ message on the multi-information display (see page
153
).
2.
If it stays on after you have fully released the parking brake while the engine is running, or if it comes on while driving, it can indicate a problem in the brake system. You will also see a ‘‘BRAKE FLUID LOW’’ or ‘‘CHECK BRAKE SYSTEM’’ message on the multi-information display. For more information, see page
472
61
2009 TSX 08/02/06 20:34:55 31TL1600 0067
Instrument Panel Indicators
Supplemental Restraint System Indicator
This indicator comes on briefly when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates a potential problem with your front airbags. This indicator will also alert you to a potential problem with your side airbags, passenger’s side airbag cutoff system, side curtain airbags, automatic seat belt tensioners, driver’s seat position sensor, or the front passenger’s weight sensors. You will also see a ‘‘CHECK AIRBAG SYSTEM’’ message on the multi-information display. For more information, see page
31
Anti-lock Brake System (ABS) Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position. If this indicator comes on at any other time, there is a problem in the ABS. If this happens, take the vehicle to your dealer to have it checked. With this indicator on, your vehicle still has normal braking ability but no anti-lock function. You will also see a ‘‘CHECK ABS SYSTEM’’ message on the multi- information display. For more information, see page
390
62
U.S.
Canada
Side Airbag Off Indicator
This indicator comes on briefly when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates that the passenger’s side airbag has automatically shut off. You will also see a ‘‘PASSENGER SIDE AIRBAG OFF’’ message on the multi- information display. For more information, see page
32
2009 TSX 08/02/06 20:35:06 31TL1600 0068
Instrument Panel Indicators
Vehicle Stability Assist (VSA) System Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position.
If it comes on and stays on at any other time, or it does not come on when you turn the ignition switch to the ON (II) position, there is a problem with the VSA system. You will also see a ‘‘CHECK VSA SYSTEM’’ message on the multi- information display. Take your vehicle to a dealer to have it checked. Without VSA, your vehicle still has normal driving ability, but will not have VSA traction and stability enhancement. For more information, see page
398
VSA Activation Indicator
This indicator has three functions:
It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system.
It flashes when VSA is active (see page
398
).
1.
2.
3.
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position, and when the ignition switch is turned to the START (III) position. For more information, see page
398
It comes on along with the VSA system indicator if there is a problem with the VSA system. You will also see a ‘‘CHECK VSA SYSTEM’’ message on the multi- information display.
63
2009 TSX 08/02/06 20:35:18 31TL1600 0069
Instrument Panel Indicators
Low Tire Pressure/ TPMS Indicator
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II) position.
This indicator has two functions:
1.
If it comes on while driving, it indicates that one or more of your vehicle’s tires are significantly low on pressure.
You will also see a ‘‘CHECK TIRE PRESSURE’’ message on the multi- information display (see page ).
394
Check the tire pressure monitor on
the multi-information display and
determine the cause (see page
394
).
64
If this happens, pull to the side of the
road when it is safe, check which tire
has lost pressure on the multi-
information display, and determine
the cause. If it is because of a flat tire,
have the flat tire repaired as soon as
possible. If two or more tires are
underinflated, call a professional
towing service. For more
information, see page
481
2.
If this indicator begins to flash,
there is a problem with the tire
pressure monitoring system
(TPMS). You will also see a
‘‘CHECK TPMS SYSTEM’’
message on the multi-information
display. The indicator continues to
flash for a while (approximately 1
minute), then stays on. If this
happens, have your dealer check
the system as soon as possible.
For more information, see page
395
Turn Signal and Hazard Warning Indicators
The left or right turn signal indicator blinks when you signal a lane change or turn. If an indicator does not blink or blinks rapidly, it usually means one of the turn signal bulbs is burned out (see pages and ). Replace the bulb as soon as possible, since other drivers cannot see that you are signaling.
434
436
When you press the hazard warning button, both turn signal indicators and all turn signals on the outside of the vehicle flash.
2009 TSX 08/02/06 20:35:28 31TL1600 0070
If you turn the steering wheel to the full left or right position repeatedly while stopping or driving at very low speed, you may feel slightly harder steering in order to prevent damage to the steering box caused by overheating.
You will also see a ‘‘CHECK POWER STEERING SYSTEM’’ message on the multi-information display.
Electric Power Steering (EPS) Indicator
This indicator normally comes on when you turn the ignition switch to the ON (II) position and goes off after the engine starts. If it comes on at any other time, there is a problem in the electric power steering system.
If this happens, stop the vehicle in a safe place and turn off the engine. Reset the system by restarting the engine. The indicator will stay on, but should go off after driving a short distance. If it does not go off, or comes back on again while driving, take the vehicle to your dealer to have it checked. With the indicator on, the EPS may be turned off, making the vehicle harder to steer.
Instrument Panel Indicators
Door/Trunk Open Indicator
This indicator comes on red if any door or the trunk lid is not closed tightly.
You will also see a corresponding indicator(s) on the multi-information display to indicate which door and/ or the trunk is not closed tightly (see page
11
).
65
2009 TSX 08/02/06 20:35:41 31TL1600 0071
Instrument Panel Indicators
Lights On Indicator
High Beam Indicator
Cruise Main Indicator
This indicator comes on with the high beam headlights. For more information, see page
111
This indicator also comes on with reduced brightness when the daytime running lights (DRL) are on (see page
114
).
Fog Light Indicator
Ifequipped This indicator comes on when you turn on the fog lights. For more information, see page
115
This indicator comes on when you turn on the cruise control system by pressing the CRUISE button on the steering wheel (see page
299
).
Cruise Control Indicator
This indicator comes on when you
set the cruise control. See page
299
cruise control.
for information on operating the
or
This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the position. If you turn the
ignition switch to the ACCESSORY (I) or the LOCK (0) position without turning off the light switch, this indicator will remain on. A reminder chime will also sound when you open the driver’s door.
U.S.TSXandCanadianTSXPremium This indicator will also come on when the light switch is in AUTO and the lights turn on automatically.
66
2009 TSX 08/02/06 20:35:53 31TL1600 0072
Low Fuel Indicator
System Message Indicator
This indicator comes on when there is a system message on the multi- information display. Press the INFO button on the steering wheel (see ) to see the message (see page page ).
71
79
Most of the time, this indicator comes on along with other indicators in the instrument panel such as the seat belt reminder indicator, SRS indicator, VSA system indicator, etc.
LOW FUEL INDICATOR
This indicator is in the fuel gauge. It comes on as a reminder that you must refuel soon. You will also see a ‘‘FUEL LOW’’ message on the multi- information display.
When the indicator comes on, there are about 2.8 U.S. gal (10.5 ) of fuel remaining in the tank. When the needle reaches E, there is a very small amount of fuel in the tank.
Instrument Panel Indicators
Security System Indicator
SECURITY SYSTEM INDICATOR
This indicator comes on when the security system is set. For more information, see page
293
67
2009 TSX 08/02/06 20:36:01 31TL1600 0073
Gauges
TACHOMETER
SPEEDOMETER
TEMPERATURE GAUGE
FUEL GAUGE
Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition.
Avoid driving with an extremely low f uel level. Running out of f uel could cause the engine to misf ire, damaging the catalytic converter.
MULTI-INFORMATION DISPLAY
U.S. model is shown.
68
2009 TSX 08/02/06 20:36:07 31TL1600 0074
Temperature Gauge This shows the temperature of the engine’s coolant. During normal operation, the pointer should rise from the bottom mark to about the middle of the gauge. In severe driving conditions, such as very hot weather or a long period of uphill driving, the pointer may rise to the upper zone. If it reaches the red (hot) mark, pull safely to the side of the road. Turn to page for instructions and precautions on checking the engine cooling system.
468
If the pointer of the temperature gauge reaches to or above the red mark, you will also see the ‘‘WATER TEMP HOT’’ message on the multi- information display. This will alert you that the engine should be cooled down.
Gauges
69
2009 TSX 08/02/06 20:36:16 31TL1600 0075
Multi-Information Display
The multi-information display in the instrument panel displays various information and messages when the ignition switch is in the ON (II) position. Some of the messages help you operate your vehicle more comfortably. Others help to keep you aware of the periodic maintenance your vehicle needs for continued trouble-free driving.
There are three types of messages; normal display messages, engine oil life and maintenance messages, and system messages.
You can select the displayed language and also customize some vehicle control settings to your liking with the multi-information display and the three buttons on the steering wheel (see page
71
).
70
Normal Display Messages
Remote transmitter 1 is used.
Remote transmitter 2 is used.
When you unlock and open the
driver’s door, the display shows
‘‘DRIVER 1’’ or ‘‘DRIVER 2’’
depending on which remote
transmitter you use, and the driver’s
seat moves to the position stored in
that remote transmitter (see page
142
).
If you do not fasten your seat belt, you will also see a ‘‘FASTEN SEAT BELT’’ message on the multi- information display when you turn the ignition switch to the ON (II) position.
These messages go off in about several seconds after you insert the ignition key.
2009 TSX 08/02/06 20:36:26 31TL1600 0076
SEL/RESET BUTTON
In the multi-information display, the system message is also displayed (see page customize your vehicle control settings (see page
) and you can
78
81
).
MIDDLE SEGMENT
UPPER SEGMENT
INFO BUTTONS (
▲ ▼
With the ignition switch in the ON (II) position, the multi-information display changes as shown in the next page each time you press the INFO ( / ) button or SEL/RESET ▲ ▼ button.
When you turn the ignition switch to the ON (II) position, what you last selected is displayed.
U.S. model is shown.
LOWER SEGMENT
The multi-information display consists of an upper segment, a middle segment and a lower segment.
Multi-Information Display
In the normal display mode, the upper and middle segments display trip computer information, such as fuel economy or average speed. The lower segment displays the odometer/trip meter (A/B), outside temperature, and engine oil life and maintenance item code(s).
CONTINUED
71
2009 TSX 08/02/06 20:36:32 31TL1600 0077
Multi-Information Display
Trip Computer (See page 74.)
Outside Temperature (See page 74.)
Engine Oil Life (See page 76.)
*
HFL (See page 77.)
Tire Pressure for each tire (See page 76.)
: Press the INFO button (
). ▲ ▼
U.S. model is shown.
72
*
This display will be shown when the Bluetooth HandsFreeLink is activated.
: Press the SEL/RESET button.
2009 TSX 08/02/06 20:36:43 31TL1600 0078
Odometer
Trip Meter
U.S.
Canada
TRIP METER A
TRIP METER B
ODOMETER
U.S. model is shown.
The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.
This meter shows the number of miles (U.S.) or kilometers (Canada) driven since you last reset it. There are two trip meters: Trip A and Trip B. Each trip meter works independently, so you can keep track of two different distances.
To reset a trip meter, display it, and then press and hold the SEL/RESET button until the number resets to ‘‘0.0.’’
Multi-Information Display
When you reset Trip A, average fuel economy A is reset at the same time. When you reset Trip B, average fuel economy B is reset.
In the customizing mode, you can set Trip A and average fuel economy A to reset at the same time when you refuel your vehicle (see page ).
89
73
2009 TSX 08/02/06 20:36:54 31TL1600 0079
Multi-Information Display
Outside Temperature
U.S.
CANADA
OUTSIDE TEMPERATURE
The temperature sensor is in the front bumper. The temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your vehicle speed is under 19 mph (30 km/h). When you start your trip, the sensor is not fully acclimatized, therefore it may take several minutes until the proper temperature is displayed.
Trip Computer
U.S.
CANADA
This shows the outside Fahrenheit temperature in U.S. models, and Centigrade temperature in Canadian models.
In certain weather conditions, temperature readings near freezing (32°F, 0°C) could mean that ice is forming on the road surface.
INST.MPG(U.S.models)/INST.L/ 100km(Canadianmodels) This shows your current fuel mileage.
You can adjust the outside temperature display (see page
88
).
When you turn off the engine, INST. MPG or INST. L/100 km is also reset.
74
2009 TSX 08/02/06 20:37:04 31TL1600 0080
AVERAGEFUELA/B This shows your vehicle’s average fuel economy in mpg (U.S. models) or liter/100 km (Canadian models) since you last reset the Trip A or Trip B.
You can customize the Trip A and AVERAGE FUEL A reset condition on the multi-information display (see page
89
).
RANGE This shows the estimated distance you can travel on the fuel remaining in the fuel tank. This distance is estimated from the fuel economy you received over the last several miles(U.S.) or kilometers (Canada), so it will vary with changes in speed, traffic, etc.
Multi-Information Display
ELAPSEDTIME This shows the time passed traveled since you last reset it. When you turn the ignition switch to the ON (II) position, ELAPSED TIME is reset.
AVERAGESPEED This shows the average speed you are traveling in miles per hour (mph) for U.S. models or kilometers per hour (km/h) for Canadian models.
If you want to reset the ELAPSED TIME manually, go to the trip computer’s ELAPSED TIME display, and press and hold the SEL/RESET button until the number resets.
You can customize the ELAPSED TIME reset condition on the multi- information display (see page ).
90
To reset the AVERAGE SPEED you have traveled, press and hold the SEL/RESET button until the number resets.
75
2009 TSX 08/02/06 20:37:13 31TL1600 0081
Multi-Information Display
Engine Oil Life
ENGINE OIL LIFE
Tire Pressure Monitor
U.S.
Canada
This shows the remaining life of the engine oil. It shows 100% after the engine oil is replaced and the display is reset. The engine oil life is calculated based on engine operating conditions. For more information, see page
409
76
When the tire pressure monitor is shown on the multi-information display, press the SEL/RESET button. The display changes as shown. You can see the pressure of each tire in this monitor. If one or more tires are low, inflate them to the correct pressure. For more information, see page
394
2009 TSX 08/02/06 20:37:19 31TL1600 0082
Multi-Information Display
Bluetooth HandsFreeLink
To use the system, your cell phone
and the HFL system must be linked.
Not all cell phones are compatible
with this system. Refer to page
for instructions on how to link
307
your cell phone to the HFL and how
to receive or make phone calls, or
visit the acura.com/handsfreelink
website.
You can receive or make phone calls from your cell phone through your vehicle’s Bluetooth HandsFreeLink (HFL) system without touching your cell phone.
77
2009 TSX 08/02/06 20:37:28 31TL1600 0083
The system message(s) triggers the appropriate indicator(s) on the instrument panel, including the system message indicator, to come on. The system message indicator does not go off until the problem(s) is corrected.
You will also hear a beep when the system message comes on for the first time.
Most of the messages are displayed for about 5 seconds, and then the normal display returns. If there are several system messages to be shown, the display switches these messages every 5 seconds.
To switch the message(s) before 5
seconds have elapsed, press the
INFO ( / ) button on the steering
wheel.
▲ ▼
Even if you press the INFO ( / ) ▲ ▼ button, some messages stay on or come on again at regular intervals until the problem is corrected.
If the system message indicator remains lit on the instrument panel, you can see the corresponding message(s) again by pressing the INFO ( / ) button repeatedly.
▲ ▼
Here is a list of all messages:
Multi-Information Display
System Messages
SYSTEM MESSAGE INDICATOR
If there is a problem with your vehicle, for example, the engine oil level is low or a door is not fully closed, the multi-information display will show you the problem. It does this by interrupting the current display with one or more messages.
78
2009 TSX 08/02/06 20:37:46 31TL1600 0084
Multi-Information Display
See page
11
See page
19
See page
19
See page
32
See page
32
U.S.
Canada
U.S.
Canada
U.S.
Canada
See page
153
See page
428
See page
472
U.S.
Canada
See page
470
See page
471
See page
470
See page
390
See page
398
See page
69
CONTINUED
79
2009 TSX 08/02/08 14:17:37 31TL1600 0085
Multi-Information Display
See page
394
See page
395
See page
395
See page
395
See page
379
See page
67
Canada only
See page
65
See page
122
See page
122
See page
123
See page
425
See page
114
See page
410
See page
411
See page
413
See page
358
80
2009 TSX 08/02/06 20:38:13 31TL1600 0086
Customized Settings
DRIVER’S ID
▲ ▼
You can customize some vehicle control settings. To enter the customizing mode, press and hold either INFO button ( / ) for more than 3 seconds. To change the settings, the ignition switch must be in the ON (II) position, and the vehicle must be stopped with the transmission in Park (automatic) or with the parking brake set (manual).
If you turn the ignition switch to the
ACCESSORY (I) or the LOCK (0) position, move the shift lever out of Park (automatic) or release the parking brake (manual), the display will change to the normal screen.
If you try to enter the customizing mode while the vehicle is moving, you will see a ‘‘MUST STOP AND SHIFT TO PARK TO CHANGE SETTINGS’’ (automatic) or ‘‘MUST STOP AND SET PARK BRAKE TO CHANGE SETTINGS’’ (manual) message and you cannot change the settings.
You can customize some vehicle control settings for ‘‘DRIVER 1’’ and ‘‘DRIVER 2’’ separately. If ‘‘DRIVER 1’’ or ‘‘DRIVER 2’’ is not displayed, customizing is not possible.
To have the driver’s ID detected, make sure your remote transmitter is linked to the system and the driver’s door is unlocked with a
Multi-Information Display
corresponding remote transmitter.
See page transmitter to your vehicle.
to link your remote
127
If the remote transmitter is not linked, ‘‘DRIVER UNKNOWN CUSTOMIZE IMPOSSIBLE’’ will be displayed, and you cannot customize the settings.
If you use the key to unlock the driver’s door, the system cannot recognize either ‘‘DRIVER 1’’ or ‘‘DRIVER 2.’’
If you want to change any vehicle control settings, select CHG SETTING, then press the SEL/ RESET button.
Refer to the table on the following pages about the settings you want to customize.
CONTINUED
81
2009 TSX 08/02/06 20:38:21 31TL1600 0087
Multi-Information Display
Group Setup METER SETUP (P.86)
POSITION SETUP (P.92) LIGHTING SETUP (P.94)
Menu Item
Description
Setting Option
Page
LANGUAGE SELECTION
Changes the language used in the display.
ADJUST OUTSIDE TEMP. DISPLAY
Changes the outside temperature reading above or below its current reading.
TRIP A RESET with REFUEL
ELAPSED TIME RESET
MEMORY POSITION LINK
INTERIOR LIGHT DIMMING TIME HEADLIGHT AUTO OFF TIMER
AUTO LIGHT SENSITIVITY
*
Causes trip meter A and the average fuel economy to reset when you refuel. Resets the elapsed time of your current trip.
Changes the driver’s seat position to a stored setting. Changes how long (in seconds) the interior lights stay on after you close the doors. Changes how long (in seconds) the exterior lights stay on after you close the driver’s door.
Changes the timing of when the headlights come on. The headlight switch needs to be in the AUTO position.
*
*
*
ENGLISH FRENCH SPANISH 5°F − 〜 ± (U.S.) 3°C − 〜 ± (Canada) ON OFF IGN OFF TRIP A ON OFF 60 sec 30 sec 60 sec 30 sec 15 sec MAX HIGH MID
*
*
*
*
0°F
*
〜
5°F
0°C
*
〜
3°C
TRIP B
15 sec
0 sec
LOW MIN
87
88
89
90
93
95
96
97
* *
Default setting
1 : 2 : U.S. TSX and Canadian TSX Premium
82
2009 TSX 08/02/06 20:38:28 31TL1600 0088
Multi-Information Display
Description
Setting Option
Page
Group Setup
DOOR SETUP (P.99)
Menu Item AUTO DOOR LOCK
Changes when the doors automatically lock.
DOOR LOCK MODE
KEYLESS LOCK ACKNOWLEDGMENT
SECURITY RELOCK TIMER
AUTO DOOR UNLOCK
Changes which doors unlock with the remote transmitter in a first push. The exterior lights flash each time you press the LOCK or UNLOCK button. A beeper will also sound when you press the LOCK button twice. Changes how long it takes (in seconds) for the doors to relock and the security system to set after you unlock but do not open the door. Changes when the doors automatically unlock.
DEFAULT ALL (P.108)
* * *
1: 2 : 3 :
Default setting Default setting for automatic transmission Default setting for manual transmission
Set/Cancel all the customized settings as default.
*
SHIFT FROM P (A/T only) WITH VEH SPD OFF DRIVER DOOR ALL DOORS ON OFF
*
*
*
90 sec 60 sec 30 sec SHIFT TO P IGN OFF OFF SET CANCEL
*
*
*
DRIVER DOOR / ALL DOORS
100
101
103
104
106
108
83
2009 TSX 08/02/06 20:38:40 31TL1600 0089
Multi-Information Display
Customize Settings You can customize some of the vehicle control settings to your preference. Here are the settings you can customize:
METER SETUP POSITION SETUP LIGHTING SETUP DOOR SETUP
When you want to change the vehicle control settings, press the INFO ( / ) button to select CHG SETTING, then press the SEL/ RESET button.
▲ ▼
84
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown on the next page. Press the INFO ( / ) button, until you see the setup you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
If you do not make any changes, select ‘‘EXIT,’’ the display returns to normal display.
You can also use the select/reset knob in the instrument panel. Turn the knob to select a setting and press it to enter your selection.
If you want the settings as they were when the vehicle left the factory, select DEFAULT ALL, as described on page
108
2009 TSX 08/02/06 20:38:46 31TL1600 0090
Any of the normal displays
Press and hold.
: Press the SEL/ RESET button. : Press the INFO button ( ). ▲ ▼
Multi-Information Display
METER SETUP See page86.
POSITION SETUP See page92.
LIGHTING SETUP See page94.
DOOR SETUP See page99.
85
2009 TSX 08/02/06 20:38:56 31TL1600 0091
Multi-Information Display
Meter Setup Here are the four custom settings for the meter setup:
LANGUAGE SELECTION ADJUST OUTSIDE TEMP. DISPLAY TRIP A RESET with REFUEL ELAPSED TIME RESET
While ‘‘METER SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
86
: Press the SEL/RESET button. ). : Press the INFO button ( ▲ ▼
2009 TSX 08/02/06 20:39:07 31TL1600 0092
LanguageSelection
Multi-Information Display
There are three language selections you can make: English, French, and Spanish. To choose the language you want, follow these instructions:
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select the desired language by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘LANGUAGE SELECTION’’ and repeat the procedure again.
CONTINUED
87
2009 TSX 08/02/06 20:39:16 31TL1600 0093
Multi-Information Display
AdjustOutsideTemp.Display
U.S. models
Canadian models
U.S. models
Canadian models
If you sometimes find that the temperature reading is a few degrees above or below the actual temperature, you can adjust it by following these instructions:
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly. Press the SEL/RESET button to enter the setting.
▲ ▼
88
Adjust the outside temperature value by pressing the INFO ( / ) button repeatedly. Press the SEL/RESET button to set the desired value.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ADJUST OUTSIDE TEMP. DISPLAY’’ and repeat the procedure again.
2009 TSX 08/02/06 20:39:26 31TL1600 0094
TripAResetWithRefuel
Multi-Information Display
To cause Trip A and average fuel for trip A to reset every time you refuel your vehicle, follow these instructions:
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘TRIP A RESET with REFUEL’’ and repeat the procedure again.
CONTINUED
89
2009 TSX 08/02/06 20:39:36 31TL1600 0095
Multi-Information Display
ElapsedTimeReset There are three elapsed time reset choices you can make:
−
IGN OFF The elapsed time is reset when you turn the ignition switch to the LOCK (0) position.
TRIP A when the Trip A is reset.
The elapsed time is reset
−
TRIP B when the Trip B is reset.
The elapsed time is reset
−
You can choose this item to customize from ‘‘METER SETUP’’ by pressing the INFO ( / ) button repeatedly.
▲ ▼
Press the SEL/RESET button to see the selections.
Select the desired setting by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/RESET button.
▲ ▼
90
2009 TSX 08/02/06 20:39:42 31TL1600 0096
Multi-Information Display
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘ELAPSED TIME RESET’’ and repeat the procedure again.
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
91
2009 TSX 08/02/06 20:39:48 31TL1600 0097
Multi-Information Display
Position Setup You can customize the MEMORY POSITION LINK setting in position setup.
While ‘‘POSITION SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the custom setting then press the SEL/RESET button to enter your selection.
▲ ▼
92
: Press the SEL/RESET button.
: Press the INFO button (
). ▲ ▼
2009 TSX 08/02/06 20:39:58 31TL1600 0098
MemoryPositionLink
Multi-Information Display
If ‘‘MEMORY POSITION LINK’’ is set to ‘‘ON,’’ the driver’s seat moves to the position stored in the memory (see page driver’s door, using the remote transmitter.
) when you open the
142
You can choose this item to customize from ‘‘POSITION SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
Press the SEL/RESET button to see the selections.
Select ON or OFF by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘MEMORY POSITION LINK’’ and repeat the procedure again.
93
2009 TSX 08/02/06 20:40:07 31TL1600 0099
Multi-Information Display
Lighting Setup Here are the three custom settings for the lighting setup:
INTERIOR LIGHT DIMMING TIME HEADLIGHT AUTO OFF TIMER AUTO LIGHT SENSITIVITY
*
While ‘‘LIGHTING SETUP’’ is shown, press the SEL/RESET button to enter the customize mode.
Each time you press the INFO ( / ▲ ) button, the screen changes as ▼ shown in the illustration. Press the INFO ( / ) button until you see the setting you want to customize, then press the SEL/RESET button to enter your selection.
▲ ▼
94
: Press the SEL/ RESET button. : Press the INFO button ( ). ▲ ▼
*
: U.S. TSX, Canadian TSX Premium
2009 TSX 08/02/06 20:40:17 31TL1600 0100
InteriorLightDimmingTime
Multi-Information Display
The interior lights fade out when you close all doors. To change how long the lights stay on before they fade out, follow these instructions:
You can choose this item to customize from ‘‘LIGHTING SETUP’’ by pressing the INFO ( / ▲ ▼
) button repeatedly.
Press the SEL/RESET button to see the selections.
Select the desired setting (15 SEC, 30 SEC, or 60 SEC) by pressing the INFO ( / ) button, then enter your selection by pressing the SEL/ RESET button.
▲ ▼
When your selection is successfully completed, the display changes as shown above, and then goes back to the customize item screen.
If the ‘‘SETTING INCOMPLETE’’ message appears, go back to ‘‘INTERIOR LIGHT DIMMING TIME’’ and repeat the procedure again.
CONTINUED
95
2009 TSX 08/02/06 20:40:24 31TL1600 0101
Multi-Information Display
HeadlightAutoOffTimer The headlights, parking lights, side marker lights, taillights, and license plate lights go off after the selected time when you remove the key from the ignition switch and close the