this:
1.
Make sure the shift lever is in Park.
2.
Press the desired memory button (1 or 2) until you hear a beep, then release the button.
CONTINUED
165
2009 TL 08/12/23 18:08:31 31TK4600 0171
Driving Position Memory System
The system will move the seat and outside mirrors to the memorized positions. The indicator in the selected memory button will flash during movement. When the adjustments are complete, you will hear two beeps, and the indicator will remain on.
To change the ‘‘MEMORY
POSITION LINK’’ setting, see page
108
To stop the system’s automatic adjustment, do any of these actions:
Press any button on the driver’s door: SET, memory button 1 or 2.
Push any of the adjustment switches for the seat.
Shift out of Park.
Adjust the outside mirrors.
If desired, you can use the adjustment switches to change the positions of the seat or outside mirrors after they are in their memorized positions. If you change the memorized position, the indicator in the memory button will go out. To keep this driving position for later use, you must store it in the driving position memory.
166
2009 TL 08/07/29 17:48:09 31TK4600 0172
Onmodelswithnavigationsystem Your vehicle has a keyless access system. This system allows you to operate the vehicle without an ignition key. When you carry the remote with you, you can lock/ unlock the door(s), unlock the trunk, and start the engine.
The system may not work if:
The battery of the remote is weak. There is strong electrical current nearby. You carry a cell phone, a laptop computer, or other electrical device near the remote. The remote is covered by metal. A vehicle is being operated with a transmitter nearby. When the remote battery is dead. When the vehicle battery is dead.
Each keyless access remote has the built-in key. This key is used to lock/ unlock the doors when the remote battery becomes weak and the power door lock/unlock operation is disabled. You cannot start the engine with this key.
Make sure the driver always carries the remote/built-in key set.
Protect the remote and the built-in key from direct sunlight, high temperature, and high humidity.
Do not drop the remote or the built-in key, and do not set heavy objects on them.
Keep the remote and the built-in key away from liquids. If they get wet, dry them immediately with a soft cloth.
The built-in keys do not contain batteries.
Keyless Access System
Always keep the remote and the built-in key away from any magnetic material.
You should have received a key number tag with your built-in key. You will need this key number if you ever have to get a lost key replaced. Use only Acura-approved key blanks.
167
2009 TL 08/07/29 17:48:18 31TK4600 0173
Keyless Access System
Keys
BUILT-IN KEYS
KEYLESS ACCESS REMOTES
KEY NUMBER TAG
The following keys come with your vehicle. Refer to page separate the keys.
for how to
191
Built-inKey This key is used to lock/unlock the doors, glove box, and trunk pass- through cover.
168
OPERATING RANGE
KeylessAccessRemote This remote is used to lock/unlock the doors and unlock the trunk. When you carry the remote, you can lock/unlock the doors, unlock the trunk, and start the engine.
You can lock/unlock the doors within about a 32 inch (about 80 cm) radius from the outside door handle. You can open the trunk within about a 32 inch (about 80 cm) radius from the trunk release switch.
Anyone can lock/unlock a door or open the trunk if the remote is within the operating range of the door or the trunk.
2009 TL 08/07/29 17:48:29 31TK4600 0174
Unlocking the Door(s)
The remote may not work if: It is too close to the vehicle. It is above or below the vehicle, even when it is within its operating range.
Each front door has a LOCK/ UNLOCK feature.
The handle of each front door has a sensor. That sensor works with the remote so you can automatically unlock the door(s).
By default, only the driver’s door unlocks when you grab its handle.
To unlock the remaining doors and the trunk, press the remote or the rear of the master door lock switch on the driver’s door.
Keyless Access System
To change the ‘‘DOOR UNLOCK MODE’’ setting, see page
111
All the doors unlock when you grab the handle of the front passenger’s door.
When you unlock the door(s), some exterior lights blink twice and the system beeps twice.
To change the ‘‘KEYLESS ACCESS
LIGHT FLASH’’ setting, see page
112
To change the ‘‘KEYLESS ACCESS BEEP’’ setting, see page
113
If you wear a glove while grabbing a front door handle, the door sensor may be slow to respond or may not respond by unlocking the doors.
CONTINUED
169
2009 TL 08/12/23 18:08:43 31TK4600 0175
Keyless Access System
If you do not open any of the doors within 30 seconds, they will automatically relock.
If a remote is within operating range while you wash your vehicle or when it is raining heavily, the door sensors may respond by unlocking the doors.
170
Each unlock sensor does not operate when:
Locking the Doors
The remote is not within the operating range.
The remote is too close to the vehicle.
When the doors are unlocked.
The remote battery is dead.
The vehicle battery is dead.
DOOR LOCK BUTTON
When you press the door lock button on the front door, all the doors and the trunk will lock.
Before locking the doors, make sure the remote is not inside the vehicle.
2009 TL 08/07/29 17:48:49 31TK4600 0176
When you lock the doors, some exterior lights blink and the system beeps once. If no exterior lights blink and/or no beeper sounds, check to see if the trunk or hood is open.
To change the ‘‘KEYLESS ACCESS
LIGHT FLASH’’ setting, see page
112
To change the ‘‘KEYLESS ACCESS BEEP’’ setting, see page
113
Within 2 seconds of pressing the
door lock button to lock the doors or
locking the doors with remote, pull
the handle to make sure the doors
are actually locked. The door unlock
sensors will not operate for about 2
seconds after the doors are locked.
Keyless Access System
DoorLockPrevention If you open the driver’s door, pull its lock tab rearward on the door, and shut it when the remote is inside the vehicle, the driver’s door will unlock. Make sure you carry the remote with you when you lock the doors.
This function is also activated on the front passenger’s door. If you open the front passenger’s door, and shut it after pulling its lock tab rearward when the remote is inside the vehicle, all doors will unlock.
The door lock button does not work if:
The remote is not within the operating range.
Any door is open.
The power mode is not set to VEHICLE OFF (LOCK).
The remote is in the keyless access slot.
The remote is too close to the vehicle.
The remote battery is dead.
The vehicle battery is dead.
171
2009 TL 08/07/29 17:49:00 31TK4600 0177
Keyless Access System
Locking and Unlocking the Trunk Opening and Closing the Trunk When you close the trunk with all doors locked, the trunk will lock.
TRUNK RELEASE SWITCH
When you unlock all the doors with the remote, built-in key or power door lock master switch, the trunk will unlock.
The trunk cannot be locked if:
The remote is too close to the trunk lid.
The remote is on the interior rear panel.
When the trunk is locked, you can open it in any of these ways:
The remote is too close to the seat-back of the rear seat or the seat cushion.
Press the trunk release button inside the vehicle.
Press the trunk button on the remote.
Push the trunk release switch when carrying the remote (if the doors are locked).
172
INNER HANDLE
To close the trunk, use the inner handle to lower the lid, then press down on the back edge.
2009 TL 08/07/29 17:49:08 31TK4600 0178
Before closing the trunk, make sure the remote is not in the trunk.
If you close the trunk when the remote is in it, the system beeps, and the trunk reopens.
Keep the trunk lid closed at all times
while driving to avoid damaging the
lid, and to prevent exhaust gas from
Carbon
getting into the interior. See
Monoxide Hazard
on page
57
Keyless Access Remote
LED
UNLOCK BUTTON
LOCK BUTTON
TRUNK RELEASE BUTTON
PANIC BUTTON
−
LOCK Press this button once to lock all doors. Some exterior lights will flash. When you push the LOCK button twice within 5 seconds, you will hear a beep to verify that the doors are locked and the security system is set.
Keyless Access System
You cannot lock the doors if any door is not fully closed, if the remote is in the keyless access remote slot, or if the power mode is in any position except the VEHICLE OFF (LOCK).
When you cannot set the security system because the trunk or hood is open, no exterior light blinks and/or no beeper sounds.
CONTINUED
173
2009 TL 08/12/24 10:25:37 31TK4600 0179
Keyless Access System
−
Press this button once
UNLOCK
to unlock the driver’s door. Press it
twice to unlock the other doors.
Some exterior lights will flash twice
each time you press the button. The
door activated map lights (if the door
activated light switch is set) will
come on when you press the
UNLOCK button. If you do not open
any door within 30 seconds, the map
lights fade out. If you relock the
doors with the remote before 30
seconds have elapsed, the lights will
go off immediately.
To change the ‘‘KEY AND REMOTE
UNLOCK MODE’’ setting, see page
125
To change the ‘‘INTERIOR LIGHT DIMMING TIME,’’ see page
116
If you unlock the doors with the remote, but do not open any doors within 30 seconds, the doors automatically relock and the security system sets.
To change the ‘‘SECURITY
RELOCK TIMER’’ setting, see page
127
To change the ‘‘KEYLESS LOCK ACKNOWLEDGMENT’’ setting, see page
126
−
TRUNK Press this button for about 1 second to open the trunk. You cannot open the trunk with the exterior trunk release switch if the remote is in the keyless access remote slot, or the power mode is in any position except VEHICLE OFF (LOCK). You cannot open the trunk with the remote if the trunk main switch in the glove box is turned off.
−
Press this button for
PANIC about 2 seconds to attract attention: the horn will sound and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote.
174
2009 TL 08/07/29 17:49:25 31TK4600 0180
Replacing the Remote Battery
Replace the battery if necessary.
Battery type: CR2032
To replace the battery: 1.
Remove the built-in key (see page
192
).
2.
Remove the upper half by carefully prying on the edge with a coin.
Keyless Access System
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
175
3.
Replace the old battery with new battery. Place the battery so the side is facing up. Snap the two halves of the remote case back together.
+
An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.
2009 TL 08/12/24 10:25:50 31TK4600 0181
Here are the settings activated with the remote:
Driving position memory (see page
164
).
Keyless memory settings (see page
96
).
Audio system settings (see page
223
).
Climate control settings (see page
214
).
Navigation system preferences (see the navigation system manual).
RemoteCare
Avoid dropping or throwing the transmitter.
Protect the transmitter from extreme temperature.
Do not immerse the transmitter in any liquid.
If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
Keyless Access System
Keyless Memory Settings
TM
DRIVER’S ID
When you unlock the door with your remote, each remote activates the keyless memory settings related to that remote. The driver’s ID (Driver 1 or Driver 2) is shown on the back of each remote.
176
2009 TL 08/07/29 17:49:41 31TK4600 0182
Engine Start/Stop Button Operating Range
The engine may not run, and some malfunctions may occur, if the remote is outside the vehicle.
The engine may not start if the remote is subjected to strong radio waves.
Also, the engine may not start if the remote is too close to the windows.
Keyless Access System
Make sure you know where the remote is when you are inside the vehicle.
Remember that you can start the engine when the remote is inside the vehicle.
Make sure you always carry the remote with you.
177
2009 TL ChangingthePowerModewithout StartingtheEngine To change the power mode without turning on the engine, press the engine start/stop button without pressing the brake pedal. The power mode will be changed as shown on the next page.
08/12/24 10:26:00 31TK4600 0183
Keyless Access System
Engine Start/Stop Button Operation This system uses the engine start/ stop button instead of an ignition switch to start and stop the engine. If you are carrying the keyless access remote, you can start the engine by pressing the engine start/stop button with the brake pedal depressed. You can also stop the engine by pushing this button when the vehicle is stopped.
SwitchingthePowerModes The keyless access system has four power modes: VEHICLE OFF (LOCK), ACCESSORY, ON, and START.
Each time you press the engine start/stop button without pressing the brake pedal while carrying the keyless access remote, the power mode switches between VEHICLE OFF (LOCK), ACCESSORY, and ON.
You can start the engine at any time by pressing the engine start/stop button, while pressing the brake pedal, with the shift lever in Park or neutral position.
178
2009 TL 08/12/24 10:26:09 31TK4600 0184
VEHICLE OFF (LOCK) Indicator in the button is off.
ACCESSORY Indicator in the button comes on green. Some electrical components such as the audio system and accessory power sockets can be operated.
ON Indicator in the button remains green when the engine is not running. (If the engine is running,this indicator is off.) All electrical components can be used.
Do the following without pressing the brake pedal.
: Press the engine start/stop button. : Press the engine start/stop button without the shift lever in P. : Shift to Park, then press the engine start/stop button.
Keyless Access System
How the mode is switched depends on the shift lever position (with or without the shift lever in Park).
With the shift lever in Park, the power mode changes from ON to VEHICLE OFF (LOCK) when you push the engine start/stop button.
To change the mode from ON to ACCESSORY with the shift lever position in Park, press the engine start/stop button twice.
To change the mode from ACCESSORY to OFF, shift to Park, then press the engine start/stop button twice.
If the keyless access system NOTE: main switch in the glove box is off, make sure to insert the keyless access remote into the keyless access slot to turn on your vehicle’s power mode. For more information, refer to page
187
179
2009 TL 08/12/24 10:26:24 31TK4600 0185
Keyless Access System
Ignition Switch and Power Mode Comparison
Ignition Switch Position
Without Keyless Access System
LOCK (0)
ACCESSORY (I)
ON (II)
START (III)
Engine is turned off and power is shut down. The steering wheel is locked. No electrical components can be used.
Engine is turned off. Some electrical components such as the audio system and accessory power sockets can be operated.
Normal key position while driving. All electrical components can be used.
Use this position to start the engine. The ignition switch returns to the ON (II) position when you release the key.
Power Mode
VEHICLE OFF (LOCK)
ACCESSORY
ON
START
Green
OFF
Indicator- Green (engine is turned off) Off (engine is running)
All electrical components can be used.
Indicator-Off The mode automatically returns to ON after the engine starts.
Indicator-Off
Indicator-Green
With Keyless Access System and Engine Start/Stop Button
Engine is turned off and power is shut down. The steering wheel is locked. No electrical components can be used.
Engine is turned off. Some electrical components such as the audio system and accessory power sockets can be operated.
180
2009 TL 08/12/24 10:26:35 31TK4600 0186
Starting the Engine
StartingGuidance
ENGINE START/STOP BUTTON
TO START ENGINE
TO TURN ACCESSORY ON
BRAKE PEDAL
You can start the engine in any power mode.
To start the engine: 1.
Move the shift lever to Park (P).
2.
Depress the brake pedal and press the engine start/stop button.
After you unlock and open the driver’s door, you will see the ‘‘TO START ENGINE:’’ message on the multi-information display. The ‘‘TO TURN ACCESSORY ON:’’ message will be shown after three seconds. The display switches between the ‘‘TO START ENGINE:’’ and ‘‘TO TURN ACCESSORY ON:’’ messages every three seconds.
Keyless Access System
Whenthekeylessaccesssystemmain the multi- switchinthegloveboxisoff, information display shows the ‘‘INSERT KEYLESS REMOTE INTO SLOT’’ message, then the ‘‘TO START ENGINE:’’ message will be shown after you insert the remote into the slot. Each time you press the engine start/stop button, the ‘‘INSERT KEYLESS REMOTE INTO SLOT’’ message is shown on the multi-information display if the remote is not in the slot.
CONTINUED
181
2009 TL 08/12/24 10:26:42 31TK4600 0187
NOTE:
If the keyless access remote battery
dies, you may have to use the built-in
key to unlock/lock the vehicle. The
built-in key is stored inside the
keyless access remote (see page
191
).
After entering the vehicle, insert the keyless access remote into the slot to start the engine (see page ).
189
Keyless Access System
TO UNLOCK WHEEL
If the steering wheel is locked, the engine cannot start. The multi- information display shows you the above message and the indicator in the engine start/stop button blinks. To unlock the steering wheel, apply force by turning it left and right while pressing the engine start/stop button at the same time.
182
2009 TL 08/12/24 10:26:52 31TK4600 0188
Stopping the Engine
OperationGuidance
SHIFT TO PARK
TO TURN VEHICLE OFF
Keyless Access System
To turn the vehicle off when the vehicle is completely stopped, shift to Park (P), then press the engine start/stop button. The engine stops and the power mode switches from ON to VEHICLE OFF (LOCK).
You can only place the vehicle in the VEHICLE OFF (LOCK) mode if the transmission is in Park. You will see the ‘‘SHIFT TO PARK’’ message on the multi-information display with the power mode in ACCESSORY if you open the driver’s door with the shift lever in a position other than P (Park).
After shifting into Park, you will see the ‘‘TO TURN VEHICLE OFF:’’ message on the multi-information display. Press the engine start/stop button twice with your foot off the brake pedal to change the power mode from ACCESSORY to VEHICLE OFF (LOCK).
CONTINUED
183
2009 TL 08/12/24 10:27:02 31TK4600 0189
EmergencyEngineStop The engine start/stop button may be used to stop the engine due to an emergency situation even while driving. If you must stop the engine, do either of the following operations:
If you are driving, the power mode switches from ON to ACCESSORY or VEHICLE OFF (LOCK) whenever you perform either procedure. However, the steering wheel will NOT lock.
Press and hold the engine start/ stop button for three seconds. Firmly press the engine start/stop button three times.
Do not press the button while driving unless it is absolutely necessary for the engine to be switched off.
If you cannot stop the engine by pressing the engine start/stop button once when the vehicle is stopped and the shift lever is in Park, do either emergency engine stop procedure. In this case, the power mode will change to VEHICLE OFF (LOCK), however, the steering wheel may NOT lock.
Keyless Access System
Before leaving the vehicle, make sure it is off. You can verify if the power is off by checking the engine start/stop button LED indicator.
If you open the driver’s door in the ACCESSORY mode, a beeper will sound. You will also see a ‘‘TO TURN VEHICLE OFF:’’ message on the multi-information display.
Press the engine start/stop button twice with your foot off the brake pedal to change the power mode to VEHICLE OFF (LOCK).
Before leaving the vehicle, make sure it is in VEHICLE OFF (LOCK).
184
2009 TL 08/12/24 10:27:11 31TK4600 0190
The displayed message goes away when you bring the remote back inside the vehicle.
If the engine is running and you take the remote out of the vehicle, it will continue to run. Once the power mode is changed to VEHICLE OFF (LOCK), the engine will not restart until you bring back a remote into the vehicle.
Keyless Access System
The engine does not start if you push the engine start/stop button when the remote is outside the vehicle. Check where the remote is. Make sure that you carry the remote with you when you operate the engine start/stop button.
Even when the remote is inside the vehicle, the beeper may sound when the location of the remote is not detected due to surrounding conditions. It is not a failure. Make sure that you carry the remote with you.
Beeper and Message KeylessRemoteNotDetected
If you take the keyless access remote out of the vehicle and close the door with the power mode ON, the inside and outside beepers sound and a ‘‘KEYLESS REMOTE NOT DETECTED’’ message will be displayed on the multi-information display.
CONTINUED
185
2009 TL 08/07/29 17:50:54 31TK4600 0191
Keyless Access System
The outside beeper sounds when the power mode is in ACCESSORY, and a door is opened, then closed.
KeylessRemoteLowBattery
The battery in the remote normally last about 2 years. To ensure maximum battery life, do not store the remote close to electrical devices such as computers or TVs. When the multi-information display shows ‘‘CHANGE KEYLESS REMOTE BATTERY,’’ replace the battery as soon as possible (see page
175
).
186
If the remote battery becomes weak
and the power door lock/unlock
operation is disabled, you should
insert the remote into the keyless
access remote slot to set the power
mode and start the engine. After
inserting the remote to the slot,
operate the engine start/stop button
as previously described (see pages
). For more information
178
on the keyless access slot, see page
189
and
181
Inserting the remote does not charge the remote battery. You should replace the battery as soon as possible.
2009 TL 08/09/04 17:24:32 31TK4600 0192
Keyless Access Remote System Main Switch
Turning off the keyless
NOTE: access system will disable lockout prevention.
With the keyless access remote system main switch off, you should insert the keyless access remote into the keyless remote slot to start the engine. For more information, see page
189
OFF
MAIN SWITCH
This switch is in the glove box. You can cancel the keyless access system features, which are locking/ unlocking the doors, unlocking the trunk, and starting the engine while carrying the keyless access remote. To cancel the system, turn the keyless access system main switch off by pushing it down.
Keyless Access System
Keyless Access System Indicator
According to the message on the multi-information display, this indicator has two indications. A ‘‘CHECK KEYLESS ACCESS SYSTEM’’ message indicates a problem with the keyless access system. A ‘‘CHECK KEYLESS STARTING SYSTEM’’ message indicates a problem with the keyless starting system.
This indicator normally comes on for several seconds when you change the power mode to ON.
CONTINUED
187
2009 TL 08/12/24 10:27:22 31TK4600 0193
Keyless Access System
CheckKeylessAccessSystem
KEYLESS ACCESS SYSTEM INDICATOR
The multi-information display shows ‘‘CHECK KEYLESS ACCESS SYSTEM.’’
CheckKeylessStartingSystem
KEYLESS ACCESS SYSTEM INDICATOR
In this case, use the built-in key to lock/unlock the doors and insert the keyless access remote into the slot to start the engine (see page ).
189
Have your vehicle checked by your dealer if:
The keyless access system indicator comes on and stays on while you are driving.
The indicator comes on after the engine has started.
188
Have your vehicle checked by your dealer if:
The keyless access system indicator comes on and stays on while you are driving.
The indicator comes on and stays on in any power mode.
2009 TL 08/07/29 17:51:20 31TK4600 0194
The multi-information display shows ‘‘CHECK KEYLESS STARTING SYSTEM.’’
In this case, you should not shut off your engine until you are in a safe location or at your dealer, as your vehicle may not restart.
Keyless Access Remote Slot
SLOT
KEYLESS ACCESS REMOTE
In either case, you have to insert the keyless access remote into the keyless access remote slot to set the power mode and start the engine.
If the remote battery becomes weak and the power door lock/ unlock operation is disabled.
When the keyless access remote system main switch in the glove box is set to off.
Keyless Access System
Always insert the keyless access remote fully into the slot. To remove it, place the vehicle in the VEHICLE OFF (LOCK) mode, then pull out the keyless access remote.
If the keyless access remote has been inserted into the slot, it will lock into place when the power is on. The slot will unlock when the power is turned off.
If the keyless access remote NOTE: does not come out of the slot easily, try to push it in before pulling it out. Make sure the vehicle is in VEHICLE OFF (LOCK) mode.
CONTINUED
189
2009 TL 08/12/24 10:27:31 31TK4600 0195
Keyless Access System
To avoid damaging the slot, do not insert any other objects into the slot or put a sticker on the keyless access remote.
Inserting the remote does not charge the remote battery. If necessary, you should replace the battery as soon as possible.
OperationGuidance
When the keyless access remote is not in the vehicle.
If you turn off the vehicle and leave the remote in the keyless access remote slot, you will hear a reminder beeper, and one of the following messages will appear on the multi- information display.
When you open the driver’s door, and each time you press the engine start/stop button, you will see the ‘‘INSERT KEYLESS REMOTE INTO SLOT’’ message on the multi- information display in the following situations:
When the keyless access system main switch (see page ) is off.
187
190
2009 TL 08/12/24 10:27:38 31TK4600 0196
Keyless Access System
The shift lever must be in Park before you can press the engine start/stop button twice without pressing the brake pedal to set the vehicle into the VEHICLE OFF (LOCK) mode.
Built-in key and Remote The built-in key can be used to lock/ unlock the doors and the trunk when the remote battery becomes weak and the power door lock/unlock operation is disabled.
CONTINUED
191
If the vehicle is left in the ACCESSORY mode, the ‘‘TO TURN VEHICLE OFF’’ message is shown on the multi-information display when you open the driver’s door. If the vehicle is left in the VEHICLE OFF (LOCK) mode with the keyless access remote in the slot, the ‘‘REMOVE KEYLESS REMOTE FROM SLOT’’ message is shown on the multi-information display.
2009 TL 08/07/29 17:51:40 31TK4600 0197
Keyless Access System
BUILT-IN KEY
The keyless access system uses an electric field to identify the remote.
If you use medical equipment such as a cardiac pacemaker, ask your doctor if the electric field used by the remote will affect it.
RELEASE BUTTON
To remove the built-in key, pull it out while pressing the release button. To reinstall the built-in key, push the key into the remote until it clicks.
To avoid damaging the remote and the built-in key, never pull on the built-in key unless you are pressing the release button.
192
Valet Function The trunk and glove box cannot be opened when you turn the trunk main switch off and lock the glove box and trunk pass-through cover with the built-in key. Then, the trunk cannot be opened by using the remote or the exterior trunk release switch.
Remove the built-in key from the remote by pressing the button, then give that remote to someone else as a valet key.
2009 TL 08/12/24 10:27:45 31TK4600 0198
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more information, see pages
178
and
180
Passenger’s Seat
*
HEATERS
Driver’s Seat
Both front seats are equipped with seat heaters. Because of the sensors for the side airbag cutoff system, there is no heater in the passenger’s seat-back. The ignition switch must be in the ON (II) position to use the heaters.
*
Seat Heaters
SEAT HEATER SWITCHES
Push the right side of the switch, HI, to rapidly heat up the seat. After the seat reaches a comfortable temperature, select LO by pushing the left side of the switch. This will keep the seat warm.
CONTINUED
193
2009 TL 08/07/29 17:51:52 31TK4600 0199
Seat Heaters
In the HI setting, the heater turns off when the seat gets warm, and turns back on after the seat’s temperature drops.
In the LO setting, the heater runs continuously. It does not cycle with temperature changes.
Follow these precautions whenever you use the seat heaters:
Use the HI setting only to heat the seats quickly, because it draws large amounts of current from the battery.
If the engine is left idling for an extended period, do not use the seat heaters even on the LO setting. It can weaken the battery, causing hard starting.
194
2009 TL 08/12/24 09:25:37 31TK4600 0200
DRIVER’S WINDOW SWITCH
*
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more information, see pages
178
and
180
*
MAIN SWITCH
FRONT PASSENGER’S WINDOW SWITCH Turn the ignition switch to the ON (II) position to raise or lower any window. To open a window, push the switch down and hold it. Release the switch when you want the window to stop. Pull back on the switch and hold it to close the window.
Closing a power window on someone’s hands or fingers can cause serious injury.
Make sure your passengers are away from the windows before closing them.
Power Windows
−
AUTO To open either front window fully, push the window switch firmly down to the second detent, then release it. The window automatically goes down all the way. To stop the window from going all the way down, pull back on the window switch briefly.
To close either front window fully, pull back the window switch firmly to the second detent, then release it. The window automatically goes all the way up. To stop the window from going all the way up, push down on the window switch briefly.
CONTINUED
195
2009 TL 08/07/29 18:06:35 31TK4600 0201
Power Windows
When you push the main switch in, the indicator comes on and the passengers’ windows cannot be raised or lowered. Use the main switch when you have children in the vehicle so they do not injure themselves by operating the windows unintentionally. To cancel this feature, push on the switch again. The switch will pop out and the indicator will go off.
The windows and the main switch will operate for up to 10 minutes after you turn off the ignition switch (set VEHICLE OFF mode on models with keyless access system). Opening either front door cancels this function.
Auto Reverse If either front window runs into any obstacle while it is closing automatically, it will reverse direction, and then stop. To close the window, remove the obstacle, then use the window switch again.
Auto reverse stops sensing when the window is almost closed. You should always check that all passengers and objects are away from the window before closing it.
Only on the driver’s window, NOTE: the auto reverse function is disabled when you continuously pull up the switch.
196
2009 TL 08/12/24 09:25:51 31TK4600 0202
Opening the Windows and Moonroof with the Remote Transmitter/Keyless Access Remote
Vehicle without keyless access system
Open
Close
Open
Close
BUILT-IN KEY
Vehicle with keyless access system
You can open all of the windows and the moonroof from outside with the remote transmitter.
1.
Press the UNLOCK button once to unlock the driver’s door.
2.
3.
Press the UNLOCK button a second time, and hold it. The remaining doors unlock, and all four windows and the moonroof start to open. To stop the windows and moonroof, release the button.
To open the windows and
moonroof further, press the
button again (within 10 seconds of
step 1) and hold it. If the windows
and the moonroof stop before the
desired position, repeat steps 1
and 2.
You cannot close the windows or the moonroof with the remote transmitter.
Power Windows
Opening/Closing the Windows and Moonroof with the Key or the Built-in key
Vehicle without keyless access system
Vehicle with keyless access system
UNLOCK BUTTON
UNLOCK BUTTON
You can open and close the windows and moonroof with the key in the driver’s door lock.
To open: 1.
Insert the key in the driver’s door lock.
CONTINUED
197
2009 TL 08/07/29 18:06:54 31TK4600 0203
Power Windows
2.
Turn the key clockwise, then release it.
3.
Turn the key clockwise again, and hold it. All four windows and the moonroof start to open. To stop the windows and the moonroof, release the key.
4.
To open the windows and the moonroof further, turn and hold the key again (within 10 seconds of step 2).
To close: 1.
Insert the key in the driver’s door lock.
2.
Turn the key counterclockwise, then release it.
3.
Turn the key counterclockwise again, and hold it. All four windows and the moonroof start to close. To stop the windows and the moonroof, release the key.
4.
To close the windows and the moonroof further, turn and hold the key again (within 10 seconds of step 2).
If the windows and the
NOTE: moonroof stop before the desired position, repeat steps 2 and 3.
198
2009 TL 08/12/24 09:26:01 31TK4600 0204
MOONROOF SWITCH
*
Open
Close
Tilt
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more information, see pages
179
and
180
To tilt up the moonroof, push on the center of the moonroof switch. To stop the moonroof from tilting up fully, push the switch briefly.
The moonroof can be tilted up in the back for ventilation, or it can be slid back into the roof. Use the switch on the front ceiling to operate the moonroof. You must turn the ignition switch to the ON (II) position to operate the moonroof.
*
To open the moonroof, pull back on the switch and hold it. Release the switch when the moonroof reaches the desired position. To close the moonroof, push the switch forward and hold it. Release the switch to stop the operation.
Moonroof
Opening or closing the moonroof on someone’s hands or fingers can cause serious injury.
Make sure all hands and fingers are clear of the moonroof before opening or closing it.
−
To open the moonroof
AUTO fully, pull back the moonroof switch firmly, then release it. The moonroof automatically opens all the way. To stop the moonroof from opening, push the switch briefly.
To close the moonroof fully, firmly push the moonroof switch forward, then release it. The moonroof automatically closes all the way. To stop the moonroof from closing, push the switch briefly.
CONTINUED
199
2009 TL 08/07/29 18:07:08 31TK4600 0205
You can use the remote transmitter/
keyless access remote or the key/
built-in key to operate the moonroof
from the outside. Refer to page
197
for details.
You can open and close the moonroof for up to 10 minutes after you turn off the ignition switch, on models with keyless access system, set the power mode to VEHICLE OFF (LOCK). Opening either front door cancels this function.
If you try to open the moonroof in below-f reezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or its motor.
Moonroof
To open or close the moonroof partially, lightly pull the switch back or push it forward and hold it. The moonroof will stop when you release the switch.
Auto Reverse If the moonroof runs into any obstacle while it is closing automatically, it will reverse direction, and then stop. To close the moonroof, remove the obstacle, then use the moonroof switch again.
Auto reverse stops sensing when the moonroof is almost closed. You should always check that all passengers and objects are away from the moonroof before closing it.
200
2009 TL 08/07/29 18:07:13 31TK4600 0206
PARKING BRAKE LEVER
To apply the parking brake, pull the lever up fully. To release it, pull up slightly, push the button, and lower the lever. The parking brake indicator on the instrument panel should go out when the parking brake is fully released (see page
65
).
If you drive without releasing the
parking brake, a beeper will sound,
and you will also see a ‘‘RELEASE
PARKING BRAKE’’ message on the
multi-information display (see page
65
).
Driving the vehicle with the parking brake applied can damage the rear brakes and hubs. A beeper will sound if the vehicle is driven with the parking brake on.
Parking Brake
201
2009 TL 08/09/04 17:35:59 31TK4600 0207
Interior Convenience Items
CONSOLE COMPARTMENT
FRONT DOOR POCKET with BEVERAGE HOLDER
COAT HOOK
USB ADAPTER CABLE
ACCESSORY POWER SOCKET
REAR DOOR POCKET
VANITY MIRROR
SUNGLASSES HOLDER
SUN VISOR
CENTER POCKET
GLOVE BOX
AUXILIARY INPUT JACK
SIDE POCKET
ACCESSORY POWER SOCKET
BEVERAGE HOLDER in REAR SEAT ARMREST
BEVERAGE HOLDER
CARGO HOOKS
202
2009 TL 08/09/04 17:36:07 31TK4600 0208
Interior Convenience Items
Beverage Holders
Front
Rear
Be careful when you are using the beverage holders. A spilled liquid that is very hot can scald you or your passengers. Liquid can also spill from the door pocket beverage holders (if equipped) when you open or close the doors. Use only resealable containers in the door pockets.