2011 Acura RDX Owners Manual

U.S. model is shown

To reduce glare at night, the instrument panel illumination dims when you turn the light switch to the

or

position.

The level of brightness is shown on the multi-information display while you adjust it. It goes out 5 seconds after you finish adjusting.

INSTRUMENT PANEL BRIGHTNESS CONTROL KNOB

The knob on the instrument panel controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness. Separate adjustments can be made when the headlights are on and off.

120

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Rear Window Defogger, Hazard Warning Button

In cold weather, the defogger will not automatically shut itself off. You must manually shut off the rear window defogger when it is no longer needed. Make sure the rear window is clear and you have good visibility before starting to drive. The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side. Pushing this button also turns the mirror heaters on or off. For more information, see page 147.

Rear Window Defogger

The rear window defogger clears fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button comes on to show the defogger is on. If you do not turn it off, the defogger will shut itself off within about 5 to 30
minutes according to the outside temperature. It also shuts off when you turn off the ignition switch. You have to turn it on again when you restart the vehicle.

Hazard Warning Button

Push the button between the center vents to turn on the hazard warning lights (four-way flashers). This causes all outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

121

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Steering Wheel Adjustments, Keys and Locks

Keys and Locks

KEY NUMBER TAG

MASTER KEYS WITH REMOTE TRANSMITTER

VALET KEY (Light Gray)

LEVER

3. Push the lever up to lock the

steering wheel in position.

4. Make sure you have securely

locked the steering wheel in place by trying to move it up, down, in, and out.

The master key fits all the locks on your vehicle. The valet key works only in the ignition and the door locks. You can keep the glove box and console compartment locked when you leave your vehicle and the valet key at a parking facility.

Steering Wheel Adjustments Make any steering wheel adjustments before you start driving.

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

1. Push the lever under the steering

column all the way down.

2. Move the steering wheel up or down, and in or out, so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.

122

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Acura-approved key blanks. These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged. ● Protect the keys from direct

sunlight, high temperature, and high humidity.

● Do not drop the keys or set heavy

objects on them.

● Keep the keys away from liquids.

If they get wet, dry them immediately with a soft cloth. The valet key does not contain a battery. Do not try to take it apart.

RetractableMasterKey

RELEASE BUTTON

Push

The master key can be retracted into the remote transmitter. To use the key, push the release button to release the key from the transmitter. The key should be fully extended. To retract the key, push the release button and at the same time push the key into the remote transmitter until it is securely latched.

Keys and Locks

Always use the fully-extended key when you insert it to the ignition switch. If the key does not fully extend, the immobilizer system may not operate properly and may prevent the engine from starting. The key may come in contact with your finger while being retracted or extended. Make sure your fingers do not touch the pivot of the key when retracting or extending the key.

123

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Immobilizer System

The immobilizer system protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine's fuel system is disabled. When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.

The system may not recognize your key's coding if another immobilizer key or other metal object (i.e. key chain) is near the ignition switch when you insert the key. If the system repeatedly does not recognize the coding of your key, contact your dealer. Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle inoperable. If you have lost your key and cannot start the engine, contact your dealer.

Always take the ignition key with you whenever you leave the vehicle alone.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation. Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser's authoritytooperatetheequipment. ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

124

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Ignition Switch

You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver's door. Remove the key to turn off the beeper. You will also see a ‘‘REMOVE KEY’’ message on the multi-information display (see page 80). The shift lever must be in Park before you can remove the key from the ignition switch.

If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key. ACCESSORY (I) － You can operate the audio system and the accessory power sockets in this position. ON (II) － This is the normal key position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position. START (III) － Use this position only to start the engine. The switch returns to the ON (II) position when you let go of the key.

125

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III). LOCK (0) － You can insert or remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly.

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Door Locks

Power Door Locks

Driver's Side

LOCK TAB

To unlock

To lock

MASTER DOOR Passenger's Side LOCK SWITCH Each front door has a master door lock switch. Either switch locks and unlocks all doors and the tailgate. Push the top of the switch to lock all doors and the tailgate; push the bottom to unlock them.

Each door has a lock tab next to the inside door handle. When you pull backward on the lock tab on the driver's door, all the doors and the tailgate lock. Pushing forward on the lock tab on the driver's door unlocks only that door. The lock tab on each passenger's door locks and unlocks only that door.

126

When the door is unlocked, you can see the red indicator on the lock tab next to the inside door handle. All doors and the tailgate can be locked from the outside by using the key in the driver's door lock. To unlock only the driver's door, insert the key, turn the key, and release it. The remaining doors and the tailgate unlock when you turn the key a second time within a few seconds. You can change the ‘‘DOOR LOCK MODE’’ setting on the multi- information display (see page 105).

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

When the vehicle speed reaches about 9 mph (about 15 km/h) or more, all the doors lock automatically. You can change the ‘‘AUTO DOOR LOCK’’ setting on the multi- information display (see page 103). When you shift to P after driving, the driver's door unlocks. You can change the ‘‘AUTO DOOR UNLOCK’’ setting on the multi- information display (see page 111).

To lock any passenger's door when getting out of the vehicle, pull backward on the lock tab and close the door. To lock the driver's door, remove the key from the ignition switch and pull backward on the lock tab. Then close the door. LockoutPrevention With the driver's door open and the key in the ignition, both master door lock switches are disabled. They are not disabled if the driver's door is closed. Pushing the switch down on the open front passenger's door will lock all doors and the tailgate.

Door Locks

Childproof Door Locks

Lock

LEVER

The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position (lever is down), the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, push the lock tab forward and use the outside door handle.

127

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Tailgate

The tailgate will lock when you lock the driver's door, and will unlock when you unlock all doors. You can change the ‘‘DOOR LOCK MODE’’ setting on the multi- information display (see page 105).

128

SWITCH

PULL POCKET

To open the tailgate, press and hold the switch, then lift up.

HANDLE

To close the tailgate, use the tailgate handle or the pull pockets to lower the tailgate, then press down on the back edge. Keep the tailgate closed at all times while driving to avoid damaging the tailgate and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page

57.

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Unlocking the Tailgate

RELEASE LEVER

UNLOCK

Tailgate

If you need to unlock the tailgate manually, it means there is a problem with the tailgate. Have the vehicle checked by your dealer.

COVER

If the power door lock system cannot unlock the tailgate, unlock it manually.

Place a cloth on the top side of the cover to prevent scratches, then use a small flat-tip screwdriver to remove the cover on the back of the tailgate.

Push the release lever to the lower right as shown with the screw driver, then push and open the tailgate.

129

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Remote Transmitter

UNLOCK BUTTON

LOCK BUTTON

PANIC BUTTON

LOCK － Press this button once to lock all doors and the tailgate. Some exterior lights will flash. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors and tailgate are locked and the security system has set. This button does not work if any door or tailgate is not fully closed. To change the ‘‘KEYLESS LOCK ACKNOWLEDGEMENT’’ setting, see page 107.

130

UNLOCK － Press this button once to unlock the driver's door. Push it twice to unlock the other doors. Some exterior lights will flash twice when you push the button. If you do not open any door or the tailgate within 30 seconds, they will automatically relock. To change the ‘‘DOOR LOCK MODE’’ setting, see page 105. To change the ‘‘SECURITY RELOCK TIMER’’ setting, see page 109.

When you press the UNLOCK button, the ceiling lights (if the front and rear ceiling light switches are in the door activated position) will come on. If you do not open any door, the lights stay on for about 30 seconds, then fade out. If you relock the doors with the remote transmitter before 30
seconds have elapsed, the lights go off immediately. To change the ‘‘INTERIOR LIGHT DIMMING TIME’’ setting, see page 98. PANIC － Press this button for about 1 second to attract attention; the horn will sound, and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any button on the remote transmitter, or turn the ignition switch to the ON (II) position.

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Remote Transmitter Care ● Avoid dropping or throwing the

transmitter.

● Protect the transmitter from

extreme temperature.

● Do not immerse the transmitter in

any liquid.

● If you lose a transmitter, the

replacement needs to be reprogrammed by your dealer.

Replacing the Transmitter Battery If it takes several pushes on the button to lock or unlock the doors and the tailgate, replace the battery as soon as possible. Battery type: CR1616

Remote Transmitter

KEYPAD

SCREW

To replace the battery: 1. Remove the screw at the base of

the transmitter with a small Phillips-head screwdriver. NOTE: Be careful when removing this screw as the head of the screw can strip out.

2. Separate the keypad from the

transmitter by pushing any button from outside.

CONTINUED 131

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Remote Transmitter

BATTERY

3. Place a cloth on the edge of the

keypad to prevent scratches, and remove the upper half by carefully prying on the edge with a small flat-tip screwdriver.

132

4. Remove the old battery and note

the polarity. Make sure the polarity of the new battery is the same (－ side facing up), then insert it in the keypad. An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.

5. Snap the two halves of the keypad,

then install the parts in reverse order.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation. Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser's authoritytooperatetheequipment. ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperatingofthedevice.

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Here is the setting activated with the remote; ● Driving position memory

(see page 148).

When you unlock and open the driver's door with the remote transmitter, the driver's seat (except the power lumbar feature) and outside mirrors start to move to the positions stored in memory. The indicator in the related memory button to the remote comes on.

Remote Transmitter

To turn off this feature, press and hold the LOCK and UNLOCK buttons at the same time. Once the remote LED blinks twice, release the buttons. Keyless memory settings for that remote are canceled. To turn the keyless memory settings back on, repeat this procedure. The LED will blink once to indicate the feature has been turned on.

Recalling a Memorized Driving Position

When you unlock the driver's door with your remote, each remote activates the keyless memory settings related to that remote. The driver's ID (MEMORY 1 or MEMORY 2) is shown on the back of

each remote.

133

2011 RDX

10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Seats

Front Seat Power Adjustments Seepages13－14forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs. The controls for the power adjustable front seats are on the outside edge of each seat bottom. You can adjust the seats with the ignition switch in any position. Make all seat adjustments before you start driving. The passenger seat has the same adjustments as the driver's seat but without any height and lumbar adjustments.

134

DRIVER'S SEAT

PASSENGER'S SEAT

Moves the seat forward and backward.

Moves the front of the seat up or down. (Driver's seat only)

Raises or lowers the seat. (Driver's seat only)

Moves the whole seat up and forward, or down and backward. The front of the seat also tilts up or down at the same time. (Driver's seat only)

Adjusts the seat-back angle forward or backward.

Increases or decreases the lumbar support. (Driver's seat only)

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Head Restraints Seepage15forimportantsafety informationandawarningabout improperlypositioningheadrestraints. Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from the likelihood of whiplash and other injuries.

They are most effective when you adjust them so the center of the back of the occupant's head rests against the center of the restraint.

Seats

Front

CUSHION

LEGS

SEAT BACK RELEASE BUTTON

AdjustingtheHeadRestraint The front and rear head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button and push the restraint down.

CONTINUED 135

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

When reinstalling a head restraint, put the legs back in place. Then adjust it to the appropriate height while pressing the release button. Make sure the removed head restraints are securely stored.

Failure to reinstall the head restraints can result in severe injury during a crash.

Always replace the head restraints before driving.

Seats

Rear

CUSHION

LEGS

SEAT BACK RELEASE BUTTON

RemovingtheHeadRestraint To remove a head restraint for cleaning or repair, pull it up as far as it will go. Push the release button, then pull the restraint out of the seat- back.

136

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Seats

This reduces the distance between the restraint and the occupant's head. It also helps protect the occupants against the likelihood of whiplash and injuries to the neck and upper spine. After a collision, the activated restraint should return to its normal position. If the restraints do not return to their normal position, or in the event of a severe collision, have the vehicle inspected by an Acura dealer.

For a head restraint system to work properly: ● Do not hang any items on the head

restraints, or from the restraint legs.

● Do not place any object between

an occupant and the seat-back.

● Install each restraint in its proper

location.

● Only use genuine Acura

replacement head restraints.

ActiveHeadRestraints

The driver's and front passenger's seats have active head restraints. If the vehicle is struck severely from the rear, the occupant properly secured with the seat belt will be pushed against the seat-back and the head restraint will automatically move forward.

137

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Seats

Armrests

Front

Rear

The lid of the console compartment can be used as an armrest.

The rear seat armrest is in the center of the rear seat. Pivot it down to use it. A beverage holder is located in the armrest.

138

Folding the Rear Seats Down The rear seat-backs can be folded down to give more cargo room. Each side folds down separately. So you can still carry a passenger in the rear seat. Remove any items from the seat before folding down the seat-back. Make sure there are no items on the floor before folding down the seats.

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Seats

BUCKLE

1. Move the front seats as far forward

as possible. Make sure the front seat-backs are in the upright positions.

2. Store the center seat belt buckle into the pocket in the rear seat- back.

3. Lower the head restraints to their

lowest positions.

4. Push the armrest back in place. 5. Lift the front edge of the rear seat

cushion, then pull up on the rear of the seat cushion, then fold the cushion forward.

RELEASE LEVER 6. Pull up the release lever on the

outside of the seat-back. Fold the seat-back forward.

7. Move the front seats backward to

the desired position.

CONTINUED 139

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

To return the seat cushion to its original position, lift up the seat cushion, then place the rear of the seat cushion at the base of the seat- back. Use the seat buckles as guides. Lower the front of the seat cushion until it locks into place. Make sure the seat-back and seat cushion are locked securely and all rear shoulder belts are positioned in front of the rear seat-backs.

INDICATOR

RELEASE LEVER

After returning the seat-back to the upright position, tug on the seat-back to make sure it is latched. If the seat- back is not latched fully, the seat belt will not work properly and you will see the red indicator behind the release lever as shown.

Seats

Do not put any heavy items on the seat-back when it is folded down. Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have to brake hard (See Carrying Cargo on page 364). Make sure that the folded down rear seat does not interfere with the front passenger's seat-back. This will cause the front passenger's weight sensors and the front passenger's seat belt reminder indicator to work improperly (see pages 21 and 33). Also check the passenger airbag off indicator to assure proper operation of the passenger's front airbag.

140

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Passenger's Seat

HEATERS

Driver's Seat Both front seats are equipped with seat heaters. The passenger seat is only heated in the seat bottom because of the side airbag cutoff system.

SEAT HEATER SWITCHES The ignition switch must be in the ON (II) position to use seat heaters. Push the top of the switch, HI, to rapidly heat up the seat. After the seat reaches a comfortable temperature, select LO by pushing the bottom of the switch. This will keep the seat warm.

Seat Heaters

In the HI setting, the heater turns off when the seat gets warm, and turns back on after the seat's temperature drops. In the LO setting, the heater runs continuously. It does not cycle with temperature changes. Follow these precautions whenever you use the seat heaters: ● Use the HI setting only to heat the

seats quickly, because it draws large amounts of current from the battery.

● If the engine is left idling for an extended period, do not use the seat heaters, even on the LO setting. It can weaken the battery, causing hard starting.

141

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

The windows will operate for up to 10
minutes after you turn off the ignition switch. Opening either front door cancels this function.

Closing a power window on someone's hands or fingers can cause serious injury.

Make sure your passengers are away from the windows before closing them.

When you push the MAIN switch in, the switch is off, and the passenger windows cannot be raised or lowered. To cancel this feature, push on the switch again to get it to pop out. Keep the MAIN switch off when you have children in the vehicle so they do not injure themselves by operating the windows unintentionally.

Power Windows

DRIVER'S WINDOW SWITCH

MAIN SWITCH Turn the ignition switch to the ON (II) position to raise or lower any window. To open the window, push the switch down and hold it. Release the switch when you want to stop the window. To close the window, pull back on the switch and hold it.

142

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

AUTO － To open or close either front window fully, push or pull the window switch firmly down or up to the second detent, and release it. The window will automatically go up or down all the way. To stop the window, pull or push the window switch briefly. To open or close either front window partially, push down or pull back on the window switch lightly to the first detent and hold it. The window will stop when you release the switch.

AUTO REVERSE － If either front window senses any obstacle while it is closing automatically, it will reverse direction and then stop. To close the window, remove the obstacle, then use the window switch again. Auto reverse stops sensing when the window is almost closed. You should always check that all passengers and objects are away from the window before closing it.

Power Windows

NOTE: The driver's window auto reverse function is disabled when you continuously pull up the switch.

143

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Moonroof

Turn the ignition switch to the ON (II) position before operating the moonroof switch on the ceiling console. To open the moonroof fully, pull back the moonroof switch firmly. The moonroof opens all the way. To stop the moonroof from opening fully, briefly move the switch in either direction. To tilt the moonroof, push the center of the moonroof switch straight up. To stop the moonroof from tilting fully open, push the moonroof switch forward.

MOONROOF SWITCH

Open

Tilt

Close

To open or close the moonroof partially, pull or push the moonroof switch lightly to the first detent and hold it. The moonroof will stop when you release the switch.

To close the moonroof fully, push the moonroof switch forward to the second detent, then release it. The moonroof closes all the way. To stop the moonroof from closing all the way, briefly move the switch in either direction.

144

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Opening or closing the moonroof on someone's hands or fingers can cause serious injury.

Make sure all hands and fingers are clear of the moonroof before opening or closing it.

Moonroof

The moonroof has a key-off delay. You can open and close the moonroof for up to 10 minutes after you turn off the ignition switch. The key-off delay cancels as soon as you open either front door. You must then turn the ignition switch to the ON (II) position for the moonroof to operate.

If you try to open the moonroof in below-freezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or motor.

Auto Reverse If the moonroof runs into any obstacle while it is closing automatically, it will reverse direction, and then stop. To close the moonroof, remove the obstacle, then use the moonroof switch again. Auto reverse stops sensing when the moonroof is almost closed. You should always check that all passengers and objects are away from the moonroof before closing it.

145

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Mirrors

Adjusting the Power Mirrors

SELECTOR SWITCH

1. Turn the ignition switch to the ON

(II) position.

2. Move the selector switch to L

(driver's side) or R (passenger's side).

The inside mirror can automatically darken to reduce glare. To turn on this feature, press the button on the bottom of the mirror. The AUTO indicator comes on as a reminder. When it is on, the mirror darkens when it senses the headlights of a vehicle behind you, then returns to normal visibility when the lights are gone. Press the button again to turn off this feature.

There is also a sensor on the back of the mirror. Items hung on the mirror may block this sensor and affect its performance.

Onmodelswithoutnavigationsystem When you shift to reverse with the ignition switch in the ON (II) position, the rear view is shown on the left side of the inside mirror. For more information, see page 348.

INDICATOR

SENSOR

AUTO BUTTON

Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.

146

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Outside mirror positions can be stored in the driving position memory system (see page 148). Reverse Tilt Door Mirror The passenger's outside mirror has a reverse tilt feature. When in reverse, the mirror will tilt down slightly to improve your view as you parallel park. Shifting out of reverse will return the mirror to its original position. ● To tilt the passenger mirror, place

the selector switch in the right position.

● To turn the feature off, place the

switch in the center or left position.

ADJUSTMENT SWITCH

3. Push the appropriate edge of the

adjustment switch to move the mirror right, left, up, or down.

4. When you finish, move the

selector switch to the center (off) position. This turns the adjustment switch off to keep your setting.

Mirrors

Heated Mirrors

HEATED MIRROR BUTTON

The outside mirrors are heated to remove fog and frost. With the ignition switch in the ON (II) position, turn on the heaters by pressing the button. The indicator in the button comes on as a reminder. Press the button again to turn the heaters off. Pressing this button also turns the rear window defogger on and off.

CONTINUED 147

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Mirrors, Driving Position Memory System

This heated mirror function has a timer (see page 121 ).

Driving Position Memory System Your vehicle has a memory feature for the driver's seat and outside mirror positions. Seat, except for power lumbar, and outside mirror positions, can be stored in separate memories. You select a memorized position by pushing the appropriate button or using the appropriate remote transmitter (Memory 1 or Memory

2).

Storing a Driving Position in Memory Store a driving position only when the vehicle is parked. 1. Turn the ignition switch to the ON (II) position. You cannot add a new driving position to the memory unless the ignition switch is in the ON (II) position. You can recall a memorized position with the ignition switch in any position. 2. Adjust the seat to a comfortable

position (see page 134). Adjust the outside mirrors for best visibility (see page 146).

148

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Driving Position Memory System

To cancel the storing procedure after pressing the SET button, do any of the following: ● Fail to press a memory button

within 5 seconds.

● Readjust the seat position. ● Readjust the outside mirror

position.

Each memory button stores only one driving position. Storing a new position erases the previous setting stored in that button's memory. If you want to add a new position while retaining the current one, use the other memory button.

Selecting a Memorized Position To select a memorized position, do this: 1. Make sure the vehicle is parked. 2. Press the desired memory button (1 or 2) until you hear a beep, then release the button.

The system will move the seat and outside mirrors to the memorized positions. The indicator in the selected memory button will flash during movement. When the adjustments are complete, you will hear two beeps, and the indicator will remain on.

SET BUTTON

MEMORY BUTTONS

3. Press and release the SET button on the driver's door. You will hear a beep. Immediately press and hold one of the memory buttons (1
or 2) until you hear two beeps. The indicator in the memory button will come on. The current positions of the driver's seat and outside mirrors are now stored.

CONTINUED 149

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Driving Position Memory System, Parking Brake

Parking Brake

Push

PARKING BRAKE PEDAL

To apply the parking brake, push the pedal down with your foot. To release it, push on the pedal again. The parking brake indicator on the instrument panel should go out when the parking brake is fully released (see page 67).

To stop the system's automatic adjustment, do any of these actions: ● Press any button on the control

panel: SET, 1, or 2.

● Push any of the adjustment

switches for the seat.

● Shift out of Park. ● Adjust the outside mirrors. If desired, you can use the adjustment switches to change the positions of the seat or outside mirrors after they are in their memorized positions. If you change the memorized position, the indicator in the memory button will go out. To keep this driving position for later use, you must store it in the driving position memory.

150

Driving the vehicle with the parking brake applied can damage the rear brakes and axles. A beeper will sound if the vehicle is driven with the parking brake on.

You will also see a ‘‘RELEASE PARKING BRAKE’’ message on the the page

multi-information display (see 79).

2011 RDX

10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Interior Lights

Ceiling Lights Front

In the ‘‘ ’’ position, both front and rear ceiling lights are off all the time. With the front ceiling lights switch in this position, the rear ceiling light does not work, and both front and rear ceiling lights do not come on when you open any door.

Rear DOOR ACTIVATED

ON

OFF

DOOR ACTIVATED

Each front and rear ceiling light has a three-position switch. Front ceiling lights: In the ‘‘ rear ceiling lights are on all the time except when the rear ceiling light switch is in the OFF position.

’’ position, both front and

Rear ceiling light: You can use the rear ceiling light independently. In the OFF position, the light does not come on even if the front ceiling light switch is in the ’’ position. In the ON position, the ‘‘ light stays on continuously except when the front ceiling light switch is in the ‘‘

’’ position.

CONTINUED 151

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Interior Lights

In the door activated position, both front and rear ceiling lights come on when you: ● Open any door. ● Remove the key from the ignition

switch.

● Unlock the doors with the key,

lock tab on the driver's door, master door lock switch, or remote transmitter.

After all doors are closed tightly, the light(s) dims slightly, then fades out in about 30 seconds.

Individual Map Lights

LENSES

If you do not open any door after unlocking the driver's door or removing the key from the ignition switch, the light(s) fade out in about 30 seconds. If you leave any door open without the key in the ignition switch, the light(s) will go off after 3
minutes. To change the ‘‘INTERIOR LIGHT DIMMING TIME’’ setting, see page

98.

You can use the front ceiling lights whenever the lights are off. To turn a light on or off, push its lens.

152

2011 RDX

10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

The courtesy light in each front door comes on when the door is opened, and goes out when the door is closed. Your vehicle also has a courtesy light in the ignition switch. This light comes on when you: ● Open any door. ● Unlock the driver's door. ● Remove the key from the ignition

switch.

After all doors are closed tightly, the light fades out in about 30 seconds. To change the ‘‘INTERIOR LIGHT DIMMING TIME’’ setting, see page 98.

Interior Lights

Cargo Area Light

ON

OFF

The cargo area light has a two position switch. In the OFF (right) position, the light does not come on. In the ON (left) position, the light comes on when you open the tailgate.

Courtesy Lights

COURTESY LIGHTS

The courtesy lights in the ceiling console come on when the parking lights are turned on. You can adjust their brightness by turning the select/reset knob on the instrument panel. In addition to the courtesy lights on the ceiling, the driver's and front passenger's ambient foot lights come

on.

153

2011 RDX 10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Interior Convenience Items

COAT HOOK

DOOR LINING POCKETS

FRONT DOOR POCKET

BEVERAGE HOLDERS

SUN VISOR/ VANITY

MIRROR

CENTER POCKET

AUXILIARY INPUT JACK

GLOVE BOX

CENTER CONSOLE

USB ADAPTER CABLE

ACCESSORY POWER SOCKETS

CARGO AREA COVER

BEVERAGE HOLDERS in REAR SEAT ARMREST

154

2011 RDX 10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Glove Box

An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.

Lock

Always keep the glove box closed while driving.

The glove box light comes on when the parking lights are on.

Interior Convenience Items

Front Door Pockets

FRONT DOOR POCKET

Open the glove box by pulling the handle to the left. Close it with a firm push. Lock or unlock the glove box with the master key.

The interior of each front door has an extendable pocket for maps and other small, lightweight items. For safety, be sure both front door pockets are closed while driving.

155

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Interior Convenience Items

Beverage Holders Be careful when you are using the beverage holders. A spilled liquid that is very hot can scald you or your passengers. Spilled liquids can damage the upholstery, carpeting, and electrical components in the interior.

Push

To use the front beverage holder, push on the lid. It will swing open. To close the lid, push it down until it latches.

The rear seat also has a beverage holder in the center armrest. To use it, pivot the armrest down.

156

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Accessory Power Sockets Front

Console Compartment

Sun Visor

Interior Convenience Items

COVER

To use the accessory power socket, pull up the cover. The ignition switch must be in the ACCESSORY (I) or ON (II) position. These sockets are intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10 amps).

COVER

None of the sockets will power an automotive type cigarette lighter element. When both sockets are being used, the combined power rating of the accessories should be 120 watts or less (10 amps).

To use the sun visor, pull it down. You can also use the sun visor at the side window. Remove the support rod from the clip and swing the sun visor toward the side window. Make sure you put the sun visor back in place when you are getting into or out of the vehicle.

157

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Console Compartment Your vehicle has a multi-function console compartment. It includes an armrest, a coin holder, a pen holder, a card holder, a removable tray, and a console compartment with two separable shelves.

MASTER KEY

Close

LID

Push

BUTTON

To open the console compartment, push the button and lift the lid. To close, lower the lid, and push it down until it latches. You can lock or unlock the console compartment lid with the master key.

Interior Convenience Items

Vanity Mirror

VANITY MIRROR

To use the vanity mirror on the back of the sun visor, pull up the cover. The light comes on when you pull up the cover.

158

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

LID

PEN HOLDER

REMOVABLE TRAY

COIN HOLDER

CARD HOLDER

You can use the inside of the lid for a pen holder, a coin holder and a card holder. The console compartment light comes on when the parking lights are on.

You can store small items on the removable tray. To remove the tray, pull it out from the console compartment frame to get more space.

Interior Convenience Items

SHELVES

The console compartment has two shelves to divide it into two levels. To store small items, you can use the upper half of the space by putting the shelves down until they latch. The front and rear shelves can be used separately. The items on each shelves should not exceed 11 lbs (5 kg). Heavy items may damage the shelves.

CONTINUED 159

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Interior Convenience Items

Cargo Area Cover

HOOK

TAB

CARGO AREA COVER

When you store a large item like a briefcase, lift the shelves up to create a large space. The maximum dimensions of the item you can store in the console compartment are: Length: 16.9 in (430 mm) Height: 12.2 in (310 mm) Width: 5.5 in (140 mm)

Your vehicle has a cargo area cover to conceal your luggage and protect them from direct sunlight. Do not put any items on top of the cargo area cover. They can block your view and be thrown around the vehicle during a crash. The cargo area cover may be removed to give you more cargo space.

HANGER BAR

To remove it: 1. Open the tailgate. Remove the

hook from the tab on the tailgate. Make sure you use both hands to prevent the cargo area cover from falling accidentally.

2. Lift and pull the rear edge of the

cargo area cover slightly to unlock it from the hanger bars, then remove it straight out.

160

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Interior Convenience Items

Coat Hook

COAT HOOK

3. Place the cargo area cover on the

cargo area floor.

Make sure the cargo area cover is securely placed so it will not move while you are driving. Reverse this procedure to install the cargo area cover.

To use a coat hook, pull it down. Make sure the coat hook is pulled up when you are not using it. This hook is not designed for large or heavy items.

161

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

162

2011 RDX10/06/08 17:42:32 11 ACURA RDX MMC North America Owner's M 50 31STK640 enu

Features

The climate control system in your vehicle provides a comfortable driving environment in all weather conditions. The standard audio system has many features. This section describes those features and how to use them. Your vehicle has an anti-theft audio system that requires a code number to enable it. The security system helps to discourage vandalism and theft of your vehicle. Onmodelswithnavigationsystem Theclimatecontrolsystemandtheaudio systemhaveavoicecontrolfeature.Refer tothenavigationsystemmanualformore information. Climate Control System .................... 164
Dual Temperature Control............. 169
Climate Control Sensors................ 171
Audio System.................................. 172
Playing the FM/AM Radio (Models without navigation system) ........ 174
To Play the Radio......................... 174
Adjusting the Sound..................... 177
without navigation system)............ 179
navigation system)....................... 185

Playing the XM® Radio (Models

Playing Discs (Models without

Disc Changer Error Messages (Models without navigation

Playing an iPod® (Models without

system).................................. 195
navigation system)....................... 197
without navigation system)............ 203

iPod® Error Messages (Models