2008 Acura RDX Owners Manual

Optional Cargo Net The cargo net can be used to help hold down light items in the cargo area. The cargo net may not prevent heavy items from being thrown forward in a crash or a sudden stop. Heavy items should be secured to the cargo area floor with the hooks or cinch straps attached to the cargo hooks.

287

2008 RDX ０７／０６／０１　１９：０８：５９　３１ＳＴＫ６１０　０２９３　

288

2008 RDX ０７／０６／０１　１９：０９：０３　３１ＳＴＫ６１０　０２９４　

Driving

This section gives you tips on starting the engine under various conditions, and how to operate the automatic transmission. It also includes important information on parking your vehicle, the braking system, the super handling-all wheel drive (SH-AWD) system, the vehicle stability assist (VSA) system, the tire pressure monitoring system (TPMS), and facts you need if you are planning to tow a trailer or drive off- highway.

Driving Guidelines Preparing to Drive Starting the Engine Automatic Transmission Driving with the Paddle

........................ ........................ ....................... ..............

Shifters

(SH-AWD) System

....................................... Super Handling-All Wheel Drive ................... ........................................... ............................. ...............

Parking Braking System Anti-lock Brakes (ABS) Tire Pressure Monitoring

. 290
. 291
. 292
. 293

. 297

. 301
. 303
. 304
. 305

System (TPMS)

........................

. 307

Vehicle Stability Assist

(VSA) System Towing a Trailer Off-Highway Driving

............................ ...........................

. 312
. 314

Guidelines

..................................

. 321

289

2008 RDX ０７／０６／０１　１９：０９：１１　３１ＳＴＫ６１０　０２９５　

Driving Guidelines

Your vehicle has higher ground clearance that allows you to travel over bumps, obstacles, and rough terrain. It also provides good visibility so you can anticipate problems earlier.

Because your vehicle rides higher off the ground, it has a high center of gravity that can cause it to roll over if you make abrupt turns. Utility vehicles have a significantly higher roll over rate than other types of vehicles.

To prevent rollovers or loss of control:

Take corners at slower speeds than you would with a passenger vehicle.

Avoid sharp turns and abrupt maneuvers whenever possible.

Do not modify your vehicle in any way that would raise the center of gravity.

Your vehicle is equipped with a super handling-all wheel drive (SH- AWD) system. When the system senses a loss of one or more wheel traction, it automatically transfers some power to the other wheels. This gives you better traction and mobility.

You still need to exercise the same care when accelerating, steering, and braking that you would in a two- wheel drive vehicle.

Do not carry heavy cargo on the roof.

Seepage foroff-highwaydriving guidelines.

321

290

2008 RDX ０７／０６／０１　１９：０９：２２　３１ＳＴＫ６１０　０２９６　

Preparing to Drive

You should do these checks and adjustments before you drive your vehicle:

1.

Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice.

2.

Check that the hood is fully closed.

3.

4.

Visually check the tires. If a tire looks low, use a gauge to check its pressure.

Check that any items you may be carrying are stored properly or fastened down securely.

5.

6.

Check the seat adjustment (see page

135

).

Check the adjustment of the inside and outside mirrors (see page

144

).

10.

When you start the engine, check the gauges and indicators in the instrument panel, and the messages on the multi-information display (see pages 77

and

61

71

).

7.

Check the steering wheel 119
adjustment (see page

).

8.

9.

Make sure the doors and the tailgate are securely closed and locked.

Fasten your seat belt. Check that your passengers have fastened ). their seat belts (see page

14

291

2008 RDX ０７／０６／０１　１９：０９：３０　３１ＳＴＫ６１０　０２９７　

Starting the Engine

1.

Apply the parking brake.

2.

In cold weather, turn off all electrical accessories to reduce the drain on the battery.

3.

Make sure the shift lever is in Park. Press on the brake pedal.

4.

Without touching the accelerator pedal, turn the ignition key to the START (III) position. Do not hold the key in the START (III) position for more than 15 seconds at a time. If the engine does not start right away, pause for at least 10 seconds before trying again.

292

The immobilizer system protects your vehicle f rom thef t. If an improperly- coded key (or other device) is used, the engine’s f uel system is disabled. For more inf ormation, see page

121

5.

6.

If the engine does not start within 15 seconds, or starts but stalls right away, repeat step 4 with the accelerator pedal pressed halfway down. If the engine starts, release pressure on the accelerator pedal so the engine does not race.

If the engine fails to start, press the accelerator pedal all the way down, and hold it there while starting to clear flooding. If the engine still does not start, return to step 5.

The engine is harder to start in cold weather. Also, the thinner air f ound at altitudes above 8,000 f eet (2,400
meters) adds to this problem.

Your vehicle has an electric vacuum pump located in the engine compartment. When you drive in cold weather or thinner air at high altitude, the electric vacuum pump operates more frequently after the engine is started.

When the electric vacuum pump is in operation, it makes some mechanical noises come from the engine compartment. This is normal.

2008 RDX ０７／０６／０１　１９：０９：３８　３１ＳＴＫ６１０　０２９８　

Shift Lever Position Indicators

These indicators on the instrument panel show which position the shift lever is in.

The ‘‘D’’ indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it flashes while driving (in any shift position), it indicates a possible problem in the transmission.

If the malfunction indicator lamp comes on along with the ‘‘D’’ indicator, there is a problem with the automatic transmission control system. Avoid rapid acceleration, and have the transmission checked by your dealer as soon as possible.

When the ‘‘D’’ indicator warns of a possible problem with the transmission, you will see a ‘‘CHECK TRANSMISSION’’ message on the multi-information display (see page 78

).

Automatic Transmission

Shifting

SHIFT LEVER

RELEASE BUTTON

To shift from Park to any position, press firmly on the brake pedal and press the release button on the front of the shift lever, then pull the lever. You cannot shift out of Park when the ignition switch is in the LOCK (0) or the ACCESSORY (I) position.

CONTINUED

293

2008 RDX ０７／０６／０１　１９：０９：４４　３１ＳＴＫ６１０　０２９９　

Automatic Transmission

To shift from:

Do this:

Press the brake pedal, and press the shift lever release button. Press the shift lever release button.

Move the shift lever.

P to R

R to P N to R D to S S to D D to N N to D R to N

294

−

This position mechani-

Park (P) cally locks the transmission. Use Park whenever you are turning off or starting the engine. To shift out of Park, you must press on the brake pedal and have your foot off the accelerator pedal. Press the release button on the front of the shift lever to move it.

If you have done all of the above and still cannot move the lever out of Park, see on page 296

Shift Lock Release

To avoid transmission damage, come to a complete stop before shifting into Park. You must also press the release button to shift into Park. The shift lever must be in Park before you can remove the key from the ignition switch.

−

Press the brake

Reverse (R) pedal and press the release button on the front of the shift lever to shift from Park to reverse. To shift from reverse to neutral, come to a complete stop, and then shift. Press the release button before shifting into reverse from neutral.

−

Use neutral if you

Neutral (N) need to restart a stalled engine, or if it is necessary to stop briefly with the engine idling. Shift to the Park position if you need to leave your vehicle for any reason. Press on the brake pedal when you are moving the shift lever from neutral to another gear.

2008 RDX ０７／０６／０１　１９：０９：４９　３１ＳＴＫ６１０　０３００　

With the shift lever in D or S, you can also use the paddle shifters to shift the transmission up or down. Once you begin to use the paddle shifters in S, the transmission will no longer upshift or downshift automatically. For more information of driving with the paddle shifters, see page

297

−

Drive (D) Use this position for your normal driving. The transmis- sion automatically adjusts to keep the engine at the best speed for the driving conditions.

−

S position (S) To shift into the S position, press the release button on the front of the shift lever, and move the lever to S. This position is similar to D, except only gears from first to fourth are selected. The S position keeps the transmission from cycling between fourth and fifth gears in stop-and-go driving.

Automatic Transmission

Engine Speed Limiter If you exceed the maximum speed for the gear you are in, the engine speed will enter into the tachometer’s red zone. If this occurs, you may feel the engine cut in and out. This is caused by a limiter in the engine’s computer controls. The engine will run normally when you reduce the rpm below the red zone.

295

2008 RDX ０７／０６／０４　１８：１３：４８　３１ＳＴＫ６１０　０３０１　

Automatic Transmission

Shift Lock Release This allows you to move the shift lever out of Park if the normal method of pushing on the brake pedal and pressing the release button does not work.

1.

Set the parking brake.

2.

Remove the key from the ignition switch.

3.

Put a cloth on the notch of the shift lock release slot cover. Using a small flat-tipped screwdriver or a metal fingernail file, carefully pry on the notch of the cover to remove it.

296

COVER

NOTCH

KEY

4.

Insert the key in the shift lock release slot.

5.

Push down on the key while you press the release button on the shift lever and move the shift lever out of Park to neutral.

RELEASE BUTTON

SHIFT LOCK RELEASE SLOT

6.

Remove the key from the shift lock release slot, then install the cover. Make sure the notch on the cover is on the rear. Return the key to the ignition switch, press the brake pedal, and restart the engine.

If you need to use the shift lock release, it means your vehicle is developing a problem. Have it checked by your dealer.

2008 RDX ０７／０６／０１　１９：１０：０６　３１ＳＴＫ６１０　０３０２　

Driving with the Paddle Shifters

Using the Paddle Shifters in D position (D-Paddle Shift Mode) When you are driving in D position, pulling the either paddle shifter switches from the ordinary automatic transmission [drive mode (D)] to the D-paddle shift mode. You can shift the transmission up or down manually with the paddle shifters.

Downshifting gives you more power when climbing, and provides engine braking when going down a steep hill.

To shift up or down, use the (right) or each side of the steering wheel.

(left) paddle shifter on

＋

−

GEAR POSITION INDICATOR

＋

Each time you pull the (right), the transmission shifts to a higher gear. Pull the (left) to downshift. You will see the selected gear number on the instrument panel.

−

When you pull either paddle shifter, the gear position indicator shows you the selected gear number.

CONTINUED

297

2008 RDX ０７／０６／０１　１９：１０：１４　３１ＳＴＫ６１０　０３０３　

Driving with the Paddle Shifters

The automatic transmission will not allow you to change shift if:

You downshift before the engine speed reaches the upper limit of the lower gear.

If you try to do this, the gear position indicator will flash the number of the lower gear several times, then return to a higher gear.

You upshift before the engine speed reaches the lower limit of the higher gear.

You press both paddle shifters at the same time.

You press one of the two paddle shifters with another paddle shifter being pressed.

The transmission control system monitors the accelerator pedal use and your driving conditions. When you press the accelerator pedal as in normal driving, the system judges that you are driving at a constant cruising speed without using the paddle shifters. Under these conditions, D-paddle shift mode is canceled, and the transmission automatically returns to drive mode(D).

When the transmission returns to drive mode (D), the displayed gear number goes out.

The transmission remains in the selected gear if you do not accelerate.

Each time you pull either paddle shifter, the transmission shifts one gear up or down. If you want to shift up or down more than two gears, pull the paddle shifter twice, pause, and then pull it again.

298

The transmission downshifts to first gear and returns to drive mode (D) when the vehicle comes to a complete stop and the vehicle speed is about 6 mph (10 km/h).

If there is a problem in the transmission while you are driving with the paddle shifters, the D indicator flashes, the D-paddle shift mode is canceled, and the transmission returns to drive mode (D).

2008 RDX ０７／０６／０１　１９：１０：２３　３１ＳＴＫ６１０　０３０４　

Driving with the Paddle Shifters

Using the Paddle Shift in S position (Sequential Shift Mode) With the shift lever in S position, you can select the sequential shift mode to shift gears; much like a manual transmission using the paddle shifters, but without a clutch pedal.

To enter the sequential shift mode, press the release button on the front of the shift lever, move the lever to the S position, then pull either paddle shifter. To cancel the sequential shift mode and return to the ordinary automatic transmission, move the shift lever from S position. When moving the shift lever, be careful not to operate incorrectly. While you are driving in the sequential shift mode, the transmission will not automatically return to ordinary automatic transmission.

GEAR POSITION INDICATOR

‘‘M’’ INDICATOR

When you move the shift lever from ‘‘D’’ to ‘‘S’’ position and pull either paddle shifter, the gear position indicator displays on ‘‘M’’ along with the selected gear number.

To upshift, pull the shifter. To downshift, pull the (left) paddle shifter.

＋

(right) paddle

−

When you accelerate from a stop, the transmission starts in first gear, and you must manually upshift between first and fifth gears. Make sure you upshift before the engine speed reaches the tachometer’s red zone.

The transmission remains in the selected gear (5, 4, 3, 2, or 1). There is no automatic downshift when you push the accelerator pedal to the floor.

When you are driving in 4th or 5th gear, the transmission downshifts to the lower gear under the following conditions:

The vehicle slows down to a certain speed.

You press the brake pedal.

CONTINUED

299

2008 RDX ０７／０６／０１　１９：１０：３２　３１ＳＴＫ６１０　０３０５　

Driving with the Paddle Shifters

Downshifting with the paddle shifter allows you to increase the engine braking when going down steep or long hills, and provides more power when climbing uphills. You can upshift the transmission manually to reduce the rpm. Driving in the higher gear helps fuel economy.

The transmission also shifts automatically as the vehicle comes to a complete stop. It downshifts to first gear when the vehicle speed reaches 6 mph (10 km/h) or less.

The automatic transmission will not allow you to change shift if:

Here are the speed ranges for upshifting and downshifting.

You downshift before the engine speed reaches the upper limit of the lower gear.

If you try to do this, the gear position indicator will flash the number of the lower gear several times, then return to a higher gear.

You upshift before the engine speed reaches the lower limit of the higher gear.

You try to shift to third or a higher gear when the vehicle is stationary.

You press both paddle shifters at the same time.

You press one of the two paddle shifters with another paddle shifter being pressed.

To shift from

→

→

→

→

To shift from

→

→

→

Speed range

over 0 mph (0 km/h)

over 8 mph (13 km/h)

over 17 mph (27 km/h)

over 47 mph (75 km/h)

Speed range

under 29 mph (47 km/h)

under 63 mph (100 km/h)

under 94 mph (150 km/h)

→

under 114 mph (182 km/h)

300

2008 RDX ０７／０６／０１　１９：１０：３９　３１ＳＴＫ６１０　０３０６　

Driving with the Paddle Shifters, Super Handling-All Wheel Drive (SH-AWD) System

StartinginSecondGear When you are in sequential shift mode, and the vehicle is stopped, pull the shift to second gear. You will see ‘‘M 2’’ in the display. Starting in second gear helps to reduce wheelspin in deep snow or on a slippery surface.

(right) paddle shifter to

＋

Super Handling-All Wheel Drive (SH-AWD) system The super handling-all wheel drive (SH-AWD) system is a full time all- wheel-drive system that automatically controls and transfers varying amounts of engine torque to all wheels independently, according to the driving conditions.

While the SH-AWD system helps to enhance the vehicle’s driving stability in all situations, it is still your responsibility to drive and corner at reasonable speeds and to leave a sufficient margin of safety.

SH-AWD Torque Distribution Monitor

TORQUE INDICATOR

TORQUE INDICATOR

The SH-AWD torque distribution monitor on the multi-information display shows you the amount of torque being sent to the wheels. Each wheel: right front (RF), left front (LF), right rear (RR), and left rear (LR), has its own torque indicator.

CONTINUED

301

2008 RDX ０７／０６／０１　１９：１０：４３　３１ＳＴＫ６１０　０３０７　

Super Handling-All Wheel Drive (SH-AWD) System

Each torque indicator is displayed as a bar graph divided into 5 segments. The number of segments represents the amount of torque distributed to each wheel.

When there is only a slight change in torque distribution while driving, such as cruising on level roads at the same speed, the torque distribution monitor may stop displaying the amount of torque. This is not a system problem. The monitor will show the amount if the system senses any change in torque distribution.

If the SH-AWD indicator blinks while driving, it indicates the differential temperature is too high. You will also see an ‘‘SH-AWD DIFF TEMP HIGH’’ message on the multi- information display. If this happens, pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out. If the indicator does not go out, take your vehicle to a dealer to have it checked.

If the SH-AWD indicator on the instrument panel stays on, and the ‘‘CHECK SH-AWD SYSTEM’’ message also appears on the multi- information display, there is problem with the SH-AWD system.

Your vehicle still has normal front- wheel drive with vehicle stability assist (VSA), but does not have the advantages of SH-AWD. Have your vehicle checked by a dealer as soon as possible.

302

2008 RDX ０７／０６／０１　１９：１０：５２　３１ＳＴＫ６１０　０３０８　

Parking

Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly, or your vehicle may roll if it is parked on an incline.

Set the parking brake before you put the transmission in Park. This keeps the vehicle from moving and putting pressure on the parking mechanism in the transmission.

Parking Tips

Make sure the moonroof and the windows are closed.

If the vehicle is facing uphill, turn the front wheels away from the curb.

Turn off the lights.

Place any packages, valuables, etc. in the cargo area or take them with you.

Lock the doors and the tailgate.

Never park over dry leaves, tall grass, or other flammable materials. The hot three way catalytic converter could cause these materials to catch on fire.

If the vehicle is facing downhill, turn the front wheels toward the curb.

Check the indicator on the instrument panel to verify that the security system is set.

Make sure the parking brake is fully released before driving away. Driving with the parking brake partially set can overheat or damage the rear brakes.

303

2008 RDX ０７／０６／０１　１９：１１：０１　３１ＳＴＫ６１０　０３０９　

Braking System

Your vehicle is equipped with disc brakes at all four wheels. A power assist using negative pressure generated by the engine and the electric vacuum pump helps reduce the effort needed on the brake pedal. The anti-lock brake system (ABS) helps you retain steering control when braking very hard.

When the electric vacuum pump is in operation, it makes some mechanical noises come from the engine compartment. This is normal.

When you drive in cold weather or thinner air at high altitude, the electric vacuum pump operates more frequently after the engine is started.

For more information about the electric vacuum pump, see page

384

304

Resting your foot on the pedal keeps the brakes applied lightly, builds up heat, and reduces their effectiveness and reduces brake pad life. In addition, fuel economy can be reduced. It also keeps your brake lights on all the time, confusing drivers behind you.

Constant application of the brakes when going down a long hill builds up heat and reduces their effective- ness. Use the engine to assist the brakes by taking your foot off the accelerator and downshifting to a lower gear.

Check your brakes after driving through deep water. Apply the brakes moderately to see if they feel normal. If not, apply them gently and frequently until they do. Be extra cautious and alert in your driving.

Braking System Design The hydraulic system that operates the brakes has two separate circuits. Each circuit works diagonally across the vehicle (the left-front brake is connected with the right-rear brake, etc.). If one circuit should develop a problem, you will still have braking at two wheels.

Brake Pad Wear Indicators All four brakes have audible brake wear indicators.

If the brake pads need replacing, you will hear a distinctive, metallic screeching sound when you apply the brake pedal. If you do not have the brake pads replaced, they will screech all the time. It is normal for the brakes to occasionally squeal or squeak when you apply them.

2008 RDX ０７／０６／０１　１９：１１：０８　３１ＳＴＫ６１０　０３１０　

The anti-lock brake system (ABS) helps prevent the wheels from locking up, and helps you retain steering control by pumping the brakes rapidly, much faster than a person can do it.

The electronic brake distribution (EBD) system, which is part of the ABS, also balances the front-to-rear braking distribution according to vehicle loading.

Youshouldneverpumpthebrakepedal. Let the ABS work for you by always keeping firm, steady pressure on the brake pedal. This is sometimes referred to as ‘‘stomp and steer.’’

You will feel a pulsation in the brake pedal when the ABS activates, and you may hear some noise. This is normal: it is the ABS rapidly pumping the brakes. On dry pavement, you will need to press on the brake pedal very hard before the ABS activates. However, you may feel the ABS activate immediately if you are trying to stop on snow or ice.

Anti-lock Brakes (ABS)

ABS Indicator

If this indicator comes on, the anti- lock function of the braking system has shut down. The brakes still work like a conventional system, but without anti-lock. You should have your dealer inspect your vehicle as soon as possible.

You will also see a ‘‘CHECK ABS SYSTEM’’ message on the multi- information display (see page 78

).

If the indicator comes on while driving, test the brakes as instructed on page

383

CONTINUED

305

2008 RDX ０７／０６／０１　１９：１１：１５　３１ＳＴＫ６１０　０３１１　

Anti-lock Brakes (ABS)

If the ABS indicator and the brake system indicator come on together, and the parking brake is fully released, the EBD system may also be shut down.

Important Safety Reminders ABS does not reduce the time or distance it takes to stop the vehicle. It only helps with the steering control during braking.

A vehicle with ABS may require a longer distance to stop on loose or uneven surfaces, such as gravel or snow, than a vehicle without anti- lock.

ABS will not prevent a skid that results from changing direction abruptly, such as trying to take a corner too fast or making a sudden lane change. Always drive at a safe speed for the road and weather conditions.

ABS cannot prevent a loss of stability. Always steer moderately when you are braking hard. Severe or sharp steering wheel movement can still cause your vehicle to veer into oncoming traffic or off the road.

383

. If the brakes feel normal,

Test your brakes as instructed on page drive slowly and have your vehicle repaired by your dealer as soon as possible. Avoid sudden hard braking which could cause the rear wheels to lock up and possibly lead to a loss of control.

The VSA indicator will come on along with the ABS indicator.

306

2008 RDX ０７／０６／０１　１９：１１：２４　３１ＳＴＫ６１０　０３１２　

Your vehicle is equipped with a tire pressure monitoring system (TPMS) that turns on every time you start the engine and monitors the pressure in your tires while driving.

Each tire has its own pressure sensor. If the air pressure of a tire becomes significantly low, the sensor in that tire immediately sends a signal that causes the low tire pressure/TPMS indicator in the instrument panel to come on. If this happens, you will see which tire is losing pressure on the multi- information display along with a ‘‘CHECK TIRE PRESSURE’’ message.

Tire Pressure Monitoring System (TPMS)

Low Tire Pressure/ TPMS Indicator

When the low tire pressure/TPMS indicator is on, one or more of your tires is significantly underinflated. You should stop and check your tires as soon as possible, and inflate them to the proper pressure as indicated on the vehicle’s tire information placard.

If you think you can safely drive a short distance to a service station, proceed slowly to the station, then inflate the tire to the recommended pressure.

If the tire is flat, or if the tire pressure is too low to continue driving, replace the tire with the compact spare tire (see page 370

).

It is possible that the pressures shown on the multi-information display and the pressures you manually measure are slightly different.

If the difference is significant or you cannot make the low tire pressure/ TPMS indicator and message on the multi-information display go out after inflating the tires to the specified values, have your dealer check the system as soon as possible.

Driving on a significantly under- inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.

Because tire pressure varies by temperature and other conditions, the low tire pressure/TPMS indicator may come on unexpectedly.

CONTINUED

307

2008 RDX ０７／０６／０１　１９：１１：３２　３１ＳＴＫ６１０　０３１３　

Tire Pressure Monitoring System (TPMS)

Although your tire pressure is monitored, you must manually check the tire pressures monthly.

Each tire, including the spare, should be checked monthly when the vehicle is cold, and set to the recommended inflation pressure as specified on the vehicle placard and in the owner’s manual (see page 361

).

For example, if you check and fill your tires in a warm area, then drive in extremely cold weather, the tire pressure will be lower than measured and could be underinflated and cause the low tire pressure/ TPMS indicator to come on. Or, if you check and adjust your tire pressure in cooler conditions, and drive into extremely hot conditions, the tire may become overinflated. However, the low tire pressure/ TPMS indicator will not come on if the tires are overinflated.

Refer to page guidelines.

360

for tire inflation

If there is a problem with the TPMS, this indicator begins to flash. It stops flashing after approximately 1
minute, then stays on. You will also see a ‘‘CHECK TPMS SYSTEM’’ message on the multi-information display (see page

310

).

308

Tire Pressure Monitor

INFO BUTTON To select the tire pressure monitor, press the INFO button several times with the ignition switch in the ON (II) position.

You will see the above display on the multi-information display when all tire pressures are normal.

2008 RDX ０７／０６／０１　１９：１１：４０　３１ＳＴＫ６１０　０３１４　

Tire Pressure Monitoring System (TPMS)

U.S.

Canada

SEL/RESET BUTTON

This shows that front left tire is losing pressure.

To see the inflation pressures of all four tires, press the SEL/RESET button. The display changes as shown above.

Each tire pressure is shown in PSI (U.S. models) or in kPa (Canadian models).

Each tire has its own pressure sensor. If the air pressure of a tire becomes significantly low, the sensor in that tire immediately sends a signal that causes the low tire pressure/TPMS indicator in the instrument panel to come on. If this happens, you will see which tire is losing pressure on the multi- information display along with a ‘‘CHECK TIRE PRESSURE’’ message.

If any of the tires has low pressure, the tire pressure monitor also shows above message to warn you about the low tire pressure when you select the display by pressing the INFO button several times. Following this display, press the SEL/RESET button to see each tire pressure. When you continue driving after installing the spare tire, you will also see this message on the multi- information display.

CONTINUED

309

2008 RDX ０７／０６／０１　１９：１１：４８　３１ＳＴＫ６１０　０３１５　

Tire Pressure Monitoring System (TPMS)

TPMS System Failure

If the low tire pressure/TPMS indicator comes on, or the multi- information display shows a ‘‘CHECK TPMS SYSTEM’’ message, the VSA system automatically turns on even when the VSA system is turned off by pressing the VSA OFF switch (see page happens, you cannot turn the VSA system off by pressing the VSA OFF switch again.

). If this

313

When you restart the vehicle with the compact spare tire, the TPMS system message will also be displayed on the multi-information display after several miles (kilometers) driving.

If there is a problem with the TPMS, the tire pressure monitor shows a ‘‘SYSTEM FUNCTION ERROR’’ message and the tire pressure readings are not displayed. If this happens, you will first see a system warning message ‘‘CHECK TPMS SYSTEM’’ on the multi-information display.

If there is a problem with the TPMS, you will see the above message on the multi-information display.

If you see this message, the system is off and is not monitoring the tire pressures. Have the system checked by your dealer as soon as possible.

Also, the low tire pressure/TPMS indicator begins to flash (see page 69

).

310

2008 RDX ０７／０６／０１　１９：１１：５５　３１ＳＴＫ６１０　０３１６　

Tire Pressure Monitoring System (TPMS)

Changing a Tire with TPMS If you have a flat tire, the low tire pressure/TPMS and tire monitor indicators will come on. Replace the indicated flat tire with the compact spare tire (see page

370

).

After the flat tire is replaced with the spare tire, the low tire pressure/ TPMS indicator stays on while driving. After several miles (kilometers) driving, this indicator begins to flash, then stays on again. You will also see a ‘‘CHECK TPMS SYSTEM’’ message on the multi- information display. This is normal; the system cannot monitor the spare tire pressure. Manually check the spare tire pressure to be sure it is correct.

This indicator and the warning message on the multi-information display will go off, after several miles (kilometers) driving, when the spare tire is replaced with the specified

regular tire equipped with the tire pressure monitor sensor.

Each wheel is equipped with a tire pressure sensor mounted inside the tire behind the valve stem. You must use TPMS specific wheels. It is recommended that you always have your tires serviced by your dealer or a qualified technician.

Never use a puncture-repairing agent in a flat tire. If used, you will have to replace the tire pressure sensor. Have the flat tire repaired by your dealer as soon as possible.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.

Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.

ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

311

2008 RDX ０７／０６／０１　１９：１２：０４　３１ＳＴＫ６１０　０３１７　

Vehicle Stability Assist (VSA) System

VSA Activation Indicator

When VSA activates, you will see the VSA activation indicator blink (see page

67

).

Vehicle Stability Assist (VSA) System Indicator

If this indicator comes on while driving, pull to the side of the road when it is safe, and turn off the engine. Reset the system by restarting the engine. If the VSA system indicator stays on or comes back on while driving, have the VSA system inspected by your dealer.

If the indicator does not come on when the ignition switch is turned to the ON (II) position, there may be a problem with the VSA system. Have your dealer inspect your vehicle as soon as possible.

You will also see a ‘‘CHECK VSA SYSTEM’’ message on the multi- information display if there is a problem with the VSA system.

),

307

If the low tire pressure/TPMS indicator comes on (see page or the multi-information display shows a ‘‘CHECK TPMS SYSTEM’’ message with the indicator flashing (see page ), the VSA system automatically turns on even when the VSA system is turned off with the VSA OFF switch. In this case, you cannot turn the VSA system off by pressing the VSA OFF switch again.

310

Without VSA, your vehicle will have normal braking and cornering ability, but it will not have VSA traction and stability enhancement.

The vehicle stability assist (VSA) system helps to stabilize the vehicle during cornering if the vehicle turns more or less than desired. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the engine’s output and by selectively applying the brakes.

When VSA activates, you may notice that the engine does not respond to the accelerator in the same way it does at other times. There may also be some noise from the VSA hydraulic system. You will also see the VSA activation indicator blink.

The VSA system cannot enhance the vehicle’s driving stability in all situations and does not control your vehicle’s entire braking system. It is still your responsibility to drive and corner at reasonable speeds and to leave a sufficient margin of safety.

312

2008 RDX ０７／０６／０１　１９：１２：１２　３１ＳＴＫ６１０　０３１８　

Vehicle Stability Assist (VSA) System

VSA Off Switch In certain unusual conditions when your vehicle gets stuck in shallow mud or fresh snow, it may be easier to free it with the VSA temporarily switched off. When the VSA system is off, the traction control system is also off. You should only attempt to free your vehicle with the VSA off if you are not able to free it when the VSA is on.

Immediately after freeing your vehicle, be sure to switch the VSA on again. We do not recommend driving your vehicle with the VSA and traction control systems switched off.

VSA OFF SWITCH

This switch is under the driver’s side vent. To turn the VSA system on and off, press and hold it until you hear a beep.

When VSA is off, the VSA activation indicator comes on as a reminder.

VSA is turned on every time you start the engine, even if you turned it off the last time you drove the vehicle.

VSA and Tire Sizes Driving with varying tire or wheel sizes may cause the VSA to malfunction. When replacing tires, make sure they are the same size and type as your original tires (see page

364

).

If you install winter tires, make sure they are the same size as those that were originally supplied with your vehicle. Exercise the same caution during winter driving as you would if your vehicle was not equipped with VSA.

313

2008 RDX ０７／０６／０１　１９：１２：１９　３１ＳＴＫ６１０　０３１９　

Towing a Trailer

Your vehicle has been designed primarily to carry passengers and their cargo. You can also use it to tow a trailer if you carefully observe the load limits, use the proper equipment, and follow the guidelines in this section.

Load Limits

Be sure to read the Driving Guidelines 321
surfaces.

if you plan to tow off paved

Off-Highway section on page

The

Total Trailer Weight: maximum allowable weight of the trailer and everything in or on it must not exceed 1,500 lbs (680 kg). Towing a load that is too heavy can seriously affect your vehicle’s handling and performance. It can also damage the engine and drivetrain.

Tongue Load: The weight that the tongue of a fully-loaded trailer puts on the hitch should be approximately 10 % of the total trailer weight. Too much tongue load reduces front-tire traction and steering control. Too little tongue load can make the trailer unstable and cause it to sway.

Exceeding any load limit or improperly loading your vehicle and trailer can cause a crash in which you can be seriously hurt or killed.

Check the loading of your vehicle and trailer carefully before starting to drive.

314

2008 RDX ０７／０６／０１　１９：１２：２８　３１ＳＴＫ６１０　０３２０　

To achieve a proper tongue load, start by loading 60 % of the load toward the front of the trailer and 40 % toward the rear, then re-adjust the load as needed.

−

The maximum

Gross Combined Weight Rating (GCWR) allowable weight of the fully loaded vehicle and trailer is 6,394 lbs (2,900
kg)

−

The maximum

Gross Vehicle Weight Rating (GVWR) allowable weight of the vehicle, all occupants, all accessories, all cargo, and the tongue load is 4,894 lbs (2,220 kg).

−

The maximum

Gross Axle Weight Ratings (GAWR) allowable weight of the vehicle, all occupants, all accessories, all cargo, and the tongue load must not exceed 2,546 lbs (1,155 kg) on the front axle, and 2,381 lbs (1,080 kg) on the rear axle.

Checking Loads The best way to confirm that all loads are within limits is to check them at a public scale. For public scales in your area, check your local phone book, or contact your trailer dealer or rental agency for assistance.

If you cannot get to a public scale, you can estimate the total trailer weight by adding the weight of your trailer (as quoted by the manufacturer) with everything in or on the trailer.

Towing a Trailer

If you normally pull the same load each time you tow a trailer, you can use a suitable scale or a special tongue load gauge to check the tongue load the first time you set up a towing combination (a fully loaded vehicle and trailer), then recheck the tongue load whenever the conditions change.

Towing Equipment and Accessories Towing can require a variety of equipment, depending on the size of your trailer, how it will be used, how much load you are towing, and where you tow.

Discuss your needs with your trailer sales or rental agency, and follow the guidelines in this section. Also make sure that all equipment is properly installed and maintained, and that it meets federal, state, province, and local regulations.

CONTINUED

315

2008 RDX ０７／０６／０１　１９：１２：３６　３１ＳＴＫ６１０　０３２１　

Towing a Trailer

Hitches Any hitch used on your vehicle must be properly bolted to the underbody.

SafetyChains Always use safety chains when you tow a trailer. Make sure the chains are secured to the trailer and hitch, and that they cross under the tongue and can catch the trailer if it becomes unhitched. Leave enough slack to allow the trailer to turn corners easily, but do not let the chains drag on the ground.

TrailerBrakes Acura requires that any trailer with a total trailer weight of 1,000 lbs (455
kg) or more have its own brakes.

If you choose electric brakes, be sure they are electronically actuated. Do not attempt to tap into your vehicle’s hydraulic system. No matter how successful it may seem, any attempt to attach trailer brakes to your vehicle’s hydraulic system will lower braking effectiveness and create a potential hazard.

See your trailer dealer or rental agency for more information on installing electric brakes.

TrailerLights Trailer lights and equipment must comply with federal, state/province, and local regulations. Check with your local trailer sales or rental agencies for the requirements in the area where you plan to tow, and use only equipment designed for your vehicle.

316

2008 RDX ０７／０６／０１　１９：１２：４２　３１ＳＴＫ６１０　０３２２　

Since lighting and wiring vary by trailer type and brand, you should have a qualified technician install a suitable connector between the vehicle and the trailer. Improper equipment or installation can cause damage to your vehicle’s electrical system and affect your vehicle warranty.

Towing a Trailer

AdditionalTowingEquipment Many states and Canadian provinces require special outside mirrors when towing a trailer. Even if they don’t, you should install special mirrors if you cannot clearly see behind you, or if the trailer creates a blind spot.

Ask your trailer sales or rental agency if any other items are recommended or required for your towing situation.

GROUND (BLACK)

HAZARD LIGHT (ORANGE)

LEFT TURN SIGNAL (YELLOW)

RIGHT TURN SIGNAL (BROWN)

BRAKE LIGHT (LIGHT GREEN)

TAILLIGHT (RED)

Your vehicle has a trailer lighting connector located under the right side tool case in the cargo area. Refer to the drawing above for the wiring color code and purpose of each pin.

317

2008 RDX ０７／０６／０１　１９：１２：５０　３１ＳＴＫ６１０　０３２３　

Towing a Trailer

Pre-Tow Checklist When preparing to tow, and before driving away, be sure to check the following:

The vehicle has been properly serviced, and the suspension, cooling system, and lights are in good operating condition.

The trailer has been properly serviced and is in good condition.

All weights and loads are within limits.

The hitch, safety chains, and any other attachments are secure.

All items in or on the trailer are properly secured and cannot shift while you drive.

The lights and brakes on your vehicle and the trailer are working properly.

Your vehicle tires and spare are properly inflated, and the trailer tires and spare are inflated as recommended by the trailer maker.

You may want to fill the fuel tank with premium fuel. Premium fuel provides improved performance.

318

2008 RDX ０７／０６／０１　１９：１２：５９　３１ＳＴＫ６１０　０３２４　

Driving Safely With a Trailer The added weight, length, and height of a trailer will affect your vehicle’s handling and performance, so driving with a trailer requires some special driving skills and techniques.

For your safety and the safety of others, take time to practice driving maneuvers before heading for the open road, and follow the guidelines in this section.

TowingSpeedsandGears Drive slower than normal in all driving situations, and obey posted speed limits for vehicles with trailers. Use the D position when towing a trailer on level roads. See ‘‘ Hills additional gear information. Do not exceed 55 mph (88 km/h). At higher speeds, the trailer may sway or affect vehicle handling.

’’ in the next column for

Drivingon

MakingTurnsandBraking Make turns more slowly and wider than normal. The trailer tracks a smaller arc than your vehicle, and it can hit or run over something the vehicle misses. Allow more time and distance for braking. Do not brake or turn suddenly as this could cause the trailer to jackknife or turn over.

Towing a Trailer

DrivingonHills When climbing hills, closely watch your temperature gauge (see page 76
). If it nears the H (Hot) mark, turn the A/C off, reduce speed and, if necessary, pull to the side of the road to let the engine cool.

When driving down hills, reduce your speed, and shift down to S position, or use the paddle shift to the lower gear (3, 2 or 1)in the S position. When towing a trailer, do not ‘‘ride’’ the brakes, and remember, it will take longer to slow down and stop when towing a trailer.

CONTINUED

319

2008 RDX ０７／０６／０１　１９：１３：０５　３１ＳＴＫ６１０　０３２５　

Towing a Trailer

If you must stop when facing uphill, use the foot brake or parking brake. Do not try to hold the vehicle in place by pressing on the accelerator, as this can cause the automatic transmission to overheat.

HandlingCrosswindsandBuffeting Crosswinds and air turbulence caused by passing trucks can disrupt your steering and cause the trailer to sway. When being passed by a large vehicle, keep a constant speed, and steer straight ahead. Do not try to make quick steering or braking corrections.

Parking Follow all normal precautions when parking, including putting the transmission in Park and firmly setting the parking brake. Also, place wheel chocks at each of the trailer’s tires.

BackingUp Always drive slowly and have someone guide you when backing up. Grip the wheel; then turn the wheel to the left to get the trailer to move to the left, and turn the wheel right to move the trailer to the right.

of the steering

bottom

320

2008 RDX ０７／０６／０１　１９：１３：１４　３１ＳＴＫ６１０　０３２６　

Off-Highway Driving Guidelines

Improperly operating this vehicle on or off pavement can cause an accident or rollover in which you and your passengers could be seriously injured or killed.

Follow all instructions and guidelines in this owner’s manual. Keep your speed low, and don’t drive faster than conditions permit.

General Information Your vehicle has been designed primarily for use on pavement. But its higher ground clearance and super handling-all wheel drive (SH- AWD) system allow you to occasionally travel on unpaved roads, to campgrounds, picnic sites, and similar locations. It is not designed for trailblazing, mountain climbing, or other challenging off-road activities.

If you decide to drive on unpaved roads, you will find that it requires somewhat different driving skills. Your vehicle will also handle somewhat differently than it does on pavement. So be sure to read this owner’s manual, pay special attention to the precautions and tips in this section, and get acquainted with your vehicle before you leave the pavement.

Important Safety Precautions To avoid loss of control or rollover, be sure to follow all precautions and recommendations.

Be sure to store cargo properly, and do not exceed your vehicle cargo load limits (see pages 284

and

314

).

Wherever you drive, make sure you and your passengers always wear seat belts.

Keep your speed low, and never go faster than the conditions allow.

It’s up to you to continually assess the situation and drive within the limits.

321

2008 RDX ０７／０６／０１　１９：１３：２４　３１ＳＴＫ６１０　０３２７　

Off-Highway Driving Guidelines

Accelerating and Braking For better traction on all surfaces, accelerate slowly and gradually build up speed. If you try to start too fast on wet soil, mud, snow, or ice, you might not have enough traction to get underway, and you may dig yourself a hole. Starting with the shift lever in D position will help you have a smoother start on snow or ice.

Keep in mind that you will usually need more time and distance to brake to a stop on unpaved surfaces. Avoid hard braking. Do not ‘‘pump’’ the brakes; let the anti-lock braking system pump them for you.

Check Out Your Vehicle Before you leave the pavement, be sure to do all scheduled maintenance and service, and inspect your vehicle for any problems. Pay special attention to the condition of the tires, and check the tire pressures.

After you return to the pavement, carefully inspect your vehicle to make sure there is no damage that could make driving it unsafe. Recheck the condition of the tires and the tire pressures.

Remember The route presents limits (too steep or bumpy roads). You have limits (driving skill and comfort). And your vehicle has limits (traction, stability, and power).

Driving off-highway can be hazardous if you fail to recognize limits and take the proper precautions.

322

Avoiding Obstacles Debris in the road can damage your suspension or other components. Because your vehicle has a high center of gravity, driving over a large obstacle, or allowing a wheel to drop into a deep hole can cause your vehicle to tip or roll over.

Driving on Slopes If you can’t clearly see all conditions or obstacles on a slope, walk the slope before you drive on it. If you have any doubt whether or not you can safely drive on the slope, don’t do it. Find another route.

If you are driving up a hill and find that you cannot continue, turnaround over. Slowly back down the hill, following the same route you took up the hill.

. Your vehicle could roll

donottryto

2008 RDX ０７／０６／０１　１９：１３：３１　３１ＳＴＫ６１０　０３２８　

Off-Highway Driving Guidelines

Crossing a Stream Avoid driving through deep water. If you encounter water in your route (a small stream or large puddle, for example), evaluate it carefully before going ahead. Make sure it is shallow, flowing slowly, and has firm ground underneath. If you are not sure of the depth or the ground, turn around and find another route.

Driving through deep water can also