2013 Volvo C30 Owners Manual

Download PDF Manual
Open Closed Horizontal air flow Vertical air flow Direct the outer air vents toward the side win- dows to defrost. 03 94 03 Climate Manual climate control Climate system control panel Blower speed Recirculation Defroster Airflow controls A/C – ON/OFF Heated driver's seat Heated front passenger's seat Rear window and door mirror defrosters Temperature selector Manual climate system functions 2. Recirculation 1. Blower The blower speed can be increased or decreased by turning the knob. If the knob is turned counterclockwise and the indicator light in the dis- play goes out, the blower and the air conditioning are switched off. The display shows the blower symbol and OFF This function can be used to shut out exhaust fumes, smoke, etc from the passen- ger compartment. The air in the passenger compartment is then recirculated, i.e. no air from outside the car is taken into the car when this function is activated. Recirculation (together with the air condition- ing system) cools the passenger compartment more quickly in very warm weather. If the air in the car recirculates for too long, there is a risk of condensation forming on the insides of the windows, especially in winter. 03 `` 95 03 Climate Manual climate control Timer The timer function minimizes the risk of mist- ing, or stale air when the recirculation function is selected, see page 84 for information on set- ting the recirculation timer. Recirculation is always disengaged when you select Defroster (3). 03 3. Defroster Directs airflow to the wind- shield and side windows and increases blower speed. 4. Airflow controls Press one of the three buttons in the illustration to activate the selected airflow. A symbol in the display above the cli- mate control panel and a lit LED in the selected button indicate that the manual func- tion has been selected. With manually selected airflow both warm and cool air can be selected. The desired temperature is selected using con- trol 9. When the defroster is activated: • Air flows to the windows at high blower speed. • The LED in the defroster button lights up when this function is activated. The air con- ditioning system is controlled to provide maximum air dehumidification. • The air conditioning is automatically switched on (can be switched off by press- ing button 5). 5. A/C – On or Off ON: The air conditioning sys- tem is engaged when the ON light is lit. OFF: The system is disen- gaged when the OFF lights up. If Defroster (3) is activated the air conditioning is always engaged. 6/7. Heated front seats* Maximum heating: 96 * Option/accessory, for more information, see Introduction. – Press the button once – both LEDs light up. Reduced heating: – Press the button a second time – one LED lights up. Seat heating off: – Press the button a third time – no LEDs are lit. 8. Heated rear window and door mirrors Press to defrost the rear win- dow and door mirrors. The rear window and door mirrors are defrosted simulta- neously if the switch is pressed once. The defrost function is active if the LED in the switch is illu- minated. • The function can be switched off manually by pressing the button, • The defrost function switches off automat- ically after 12–20 minutes, depending on the outside temperature. NOTE On certain markets, the defrost function may remain on longer than 20 minutes in cold weather to help keep the rear window free from ice or condensation. 03 Climate Manual climate control 9. Temperature selector The knob with the thermome- ter symbol is used to select cooling or heating for both the driver's and passenger's sides of the car. 03 97 03 Climate Electronic Climate Control (ECC)* 03 Auto – On/Off Blower speed Recirculation Defroster Airflow controls A/C – ON/OFF Heated driver's seat Heated front passenger's seat Rear window and door mirror defrosters Temperature selector NOTE • The sunlight sensor on the upper side of the dashboard and the passenger com- partment temperature sensor, located behind the climate system control panel, should not be obstructed. • The air conditioning system is tempo- rarily switched off during full throttle acceleration. 98 * Option/accessory, for more information, see Introduction. ECC functions 1. Auto – On/Off The AUTO function automat- ically regulates climate con- trol to maintain the desired temperature. The automatic function controls heating, air conditioning, blower speed, recirculation, and air distribu- tion. If you select one or more manual functions, the remaining functions continue to be controlled automatically. All manual settings are switched off when AUTO is switched on. AUTO CLIMATE is shown in the display. 2. Blower speed The blower speed can be increased or decreased by turning the knob. The blower speed is regulated automati- cally if AUTO is selected. The previously set blower speed is disconnected. NOTE If the knob is turned counterclockwise and the blower indication in the display goes out, the blower and the air conditioning are switched off. The display shows the blower symbol and OFF. 3. Recirculation This function is used to recir- culate the air in the passenger compartment, which means that when the function is active, no outside air enters the compartment. This is par- ticularly useful in hot or cold weather to cool or heat the passenger com- partment faster, or to help shut out exhaust fumes, etc. Press the button repeatedly to close out out- side air (recirculation) or to let outside air flow into the passenger compartment. • If the green indicator light to the left is on, recirculation is on and no outside air flows into the passenger compartment. • If the green indicator light to the right is on, outside air flows into the passenger com- partment. While the indicator light on the right side is on, the ECC system automatically controls the flow of air into the passenger compartment and the air intake is opened or closed depending on the outside temperature, the need to heat or cool the compartment, etc. If the air in the car recirculates for too long, there is a risk of condensation forming on the insides of the windows, especially in winter. Recirculation timer The timer function minimizes the risk of fogging or stale air when the recirculation function is selected, see page 84 for information on set- ting the recirculation timer. NOTE If the defroster function is switched on (by pressing button 4), recirculation is always disengaged. 03 03 Climate Electronic Climate Control (ECC)* Interior Air Quality System (IAQS)* This system consists of a mul- tifilter that helps reduce gases and particles in the incoming air and an air quality sensor that detects increased levels of contaminants in the outside air. When the air quality sen- sor detects contaminated outside air, the air intake closes and the air inside the passenger compartment is recirculated. The filter also cleans recirculated passenger compartment air. When IAQS is engaged, the green indicator light above A is illuminated. To activate IAQS: – Press AUTO (1). Or: Toggle between the system's three modes by pressing the button the recirculation button repeatedly. • The green indicator light above A is on: IAQS is engaged. Outside air flows into the passenger compartment and is filtered. While this light is on, the ECC system auto- matically controls the flow of air into the passenger compartment and the air intake is opened or closed depending on the out- side temperature, the need to heat or cool * Option/accessory, for more information, see Introduction. 99 03 03 Climate Electronic Climate Control (ECC)* the compartment or if the IAQS sensor has detected contaminants in the incoming air. • The green indicator light above M is on: recirculation is engaged and no outside air flows into the passenger compartment. • Both indicator lights are off. Recirculation is switched off (unless ECC activates it to help cool the passenger compartment faster in hot weather). Outside air flows into the passenger compartment and is filtered. However, when both indicator lights are off, the IAQS sensor is deactivated and will not monitor the outside air for contami- nants. Keep the following in mind: • As a rule, IAQS should always be engaged. • In cold weather, the recirculation function is limited to help avoid condensation on the windows. • If condensation forms, using the defroster functions for the windshield/front side win- dows and the rear window will help clear the condensation. 4. Defroster Directs airflow to the wind- shield and side windows and increases blower speed. When the defroster is acti- vated: • Air flows to the windows at high blower speed. • The LED in the defroster button lights up when this function is activated. The air con- ditioning system is controlled to provide maximum air dehumidification. • The air conditioning is automatically switched on (can be switched off by press- ing button 6). The air is not recirculated. 5. Airflow controls Press one of the three buttons in the illustration to activate the selected airflow. A symbol in the display above the cli- mate control panel and a lit LED in the selected button indicate that the manual func- tion has been selected. With manually selected airflow both warm and cool air can be selected. See also the table on page 100. 6. Air conditioning On/Off ON: The air conditioning sys- tem is engaged when the ON light is lit and is controlled automatically by the system to maintain the selected tem- perature. OFF: The system is disengaged when the OFF lights up When OFF is selected and the OFF LED is lit, the air conditioning system is deactivated. Other functions are still controlled automati- cally. When Defroster (4) is selected, the air condi- tioning system is activated for maximum dehu- midifying. 7 and 8. Heated front seats* Maximum heating: – Press the button once – both LEDs light up. Reduced heating: – Press the button a second time – one LED lights up. Seat heating off: – Press the button a third time – no LEDs are lit. 100 * Option/accessory, for more information, see Introduction. 9. Rear window and door mirror defrosters – Press to defrost the rear window and door mirrors. The rear window and door mirrors are defros- ted simultaneously if the switch is pressed once. The defrost function is active if the LED in the switch is illuminated. • The function can be switched off manually by pressing the button. • The defrost function switches off automat- ically after 12–20 minutes, depending on the outside temperature. NOTE • On certain markets, the defrost function may remain on longer than 20 minutes in cold weather to help keep the rear window free from ice or condensation. 03 Climate Electronic Climate Control (ECC)* 03 10. Temperature selector The temperatures on the driv- er's and passenger's sides can be set separately using the knob (with the thermome- ter in it). The temperature can be set for both sides of the car when the ignition is switched on (both LEDs will be on), which means that a temperature setting will apply to both sides of the car. To set the temperature on one side of the car: 1. Press the knob once. The LED for one side of the car will light up. Turn the knob to adjust the temperature. 2. Press the knob a second time to set the temperature on the opposite side of the car. 3. Press the knob a third time to set the tem- perature on both sides of the car at the same time. NOTE Selecting a temperature that is higher or lower than necessary will not heat or cool the passenger compartment faster. * Option/accessory, for more information, see Introduction. 101 03 Climate Air distribution Air distribution Use: Air distribution Use: Defrost/de-fog the wind- shield and front side win- dows. Air to the floor and win- dows. There is also a certain amount of airflow to the dashboard air vents. For comfortable condi- tions and good defrosting in cold weather. Medium to high blower speed. Defroster. Air is not recirculated in this mode. Air conditioning is always engaged. There is also a certain amount of airflow to the panel air vents. Air to windshield and front side windows. There is also a certain amount of airflow to the dashboard air vents. Air to the windows and from the dashboard air vents. Prevents fogging in cold or humid weather (blower speed should be moder- ate to high). For good comfort in warm, dry weather. Airflow directed to the head and chest from the dashboard air vents. To ensure efficient cooling in a warm weather. Air to the floor and from the dashboard air vents. For sunny weather with cool ambient tempera- tures. Air to the floor. There is a certain amount of airflow to the dash- board and window air vents. Airflow to the windows, dashboard air vents, and floor. To warm the feet. For cooler air toward the feet, or for warmer air toward the head and chest. 03 102 03 Climate 03 103 Front seats............................................................................................ 106 Interior lighting...................................................................................... 113 Storage compartments......................................................................... 114 Rear seat............................................................................................... 117 Cargo area............................................................................................ 120 104 INTERIOR 04 Interior Front seats Manual seat adjustment Turn this knob to adjust the backrest tilt. Accessing the rear seat Control panel for the optional power seats. NOTE Both front seats are equipped with head restraints that can be adjusted vertically to suit the height of the passenger. The upper edge of the head restraint should be at least on a level with the upper-most point of the seat occupant's ear (see the section "Adjusting the front seat head restraints" on page 111). WARNING • Do not adjust the seat while driving. • Adjust the driver’s seat and seat belt (see page 20) before driving. The seat should be adjusted so that the brake pedal can be depressed fully. • Position the seat as far rearward as comfort and control allow. Seat access buttons (power seat shown) Seat adjustment handle Seat adjustment button 04 106 The driver's and passenger's seats can be adjusted in a number of ways to provide a comfortable driving and sitting position. Forward-rearward: Pull the lever up and slide the seat to the position of your choice. Use this control to raise or lower (pump up or down) the front edge of the seat cushion. Use this control to raise or lower (pump up or down) the rear edge of the seat cushion. Turn this knob (optional on some passeng- er's seats) to adjust the firmness of the lumbar support1. 1 Also applies to the optional power seat. Manual seat Moving the seat forward: Moving the seat rearward: 04 Interior Front seats Remove the seat belt from its guide (see page 21). Pull up the handle. Fold down the backrest and move the seat forward. Push the seat rearward to the desired posi- tion. 2. Fold up the backrest. 3. Put the seat belt back in its guide. When the seat has been pushed rearward, if it doesn't return to the position it was in before it was moved forward, do as follows: 1. Sit in the seat. 2. Lift handle 1 (see the illustration on page 106) and move the seat as far back as pos- sible. 04 `` 107 04 Interior Front seats 3. While holding the handle up, move the seat forward to the desired position and release the handle. Power seat Moving the seat forward: Pull up the handle. Fold down the backrest until it locks in position. Hold down the front section of the button. If the seat is in a high position, it will be lowered automatically so that the head restraint does not come in contact with the sun visor. Remove the seat belt from its guide (see page 21). 04 108 Moving the seat rearward: NOTE Adjusting the seat The seat can only be moved as far forward as possible (approx. 2.5 in./6 cm) to allow access to the rear seat with the backrest folded down. If the backrest is folded up when the seat is in the forward position, the seat will automatically move rearward (approx. 2.5 in./6 cm) after several seconds. WARNING After the seat has been returned to its orig- inal position, be sure that the backrest is securely locked in the upright position. 04 Interior Front seats 04 Lift the handle and fold up the backrest. Hold down the rear section of the button. 3. Return the seat belt to its guide. The front passenger's seat belt should be in its guide while the vehicle is being driven, even if the seat is not occupied. Power seats* The power driver's seat can be adjusted: • If the ignition key is in position I or II. • During a 10 minute period after the doors have been unlocked if the door remains open. • If the door is closed and the ignition key is not yet in the ignition, or if the key is in position 0, the seat can be adjusted or dur- ing a period of 40 seconds. The power passenger's seat can only be adjusted if the ignition key is in position I or II, or if the engine is running. Seat adjustment controls Seat adjustment controls 1, 2, 3, and 4 on the side of the seat can be used to move the seat to the position of your choice. Move this section of the control up or down to raise/lower the front section of the seat cushion. Move the control forward/rearward to move the seat forward or rearward. Move this section of the control up or down to raise/lower the rear section of the seat cushion. Backrest tilt. * Option/accessory, for more information, see Introduction. 109 04 Interior Front seats NOTE Both front seats are equipped with head restraints that can be adjusted vertically to suit the height of the passenger. The upper edge of the head restraint should be at least on a level with the upper-most point of the seat occupant's ear (see the section "Adjusting the front seat head restraints" on page 111). 04 NOTE The power seats have an overload protector that activates if a seat is blocked by any object. If this occurs, switch off the ignition (key in position 0) and wait for approxi- mately 20 seconds before operating the seat again. Emergency stop If the seat inadvertently begins to move, press any of the buttons to stop the seat. Programming the seat memory, driver's seat only* Power seat memory buttons Three different seating positions can be stored in the seat's memory. The memory buttons are located on the outboard side of the driver's seat (see the illustration above). The following example explains how memory button 1 can be programmed. Buttons 2 and 3 can be pro- grammed in the same way. To program (store) a seat position in memory button 1: 1. Adjust the seat to the desired position. 2. Press and hold down the "M" (Memory) button. 3. With the "M" button depressed, press memory button 1 to store the seat's current position. To move the seat to the position that it was in when memory button 1 was programmed, press and hold down button 1 until the seat stops moving. As a safety precaution, the seat will stop auto- matically if the button is released before the seat has reached the preset position. Central locking system remote key and driver's seat memory The remote key transmitter can also be equip- ped with an optional function that controls the electrically operated driver's seat in the follow- ing way: 1. Adjust the seat to the desired position. 2. When you leave the car, lock it using the remote key. 3. The next time the driver's door is unlocked with the same remote key and that door is opened within 2 minutes, the driver's seat and side door mirrors will automatically move to the position that they were in when the doors were most recently locked with the same remote key. 110 * Option/accessory, for more information, see Introduction. NOTE The memory function in the remote key operates independently the memory func- tion in the seat. WARNING • Because the driver's seat can be adjusted with the ignition off, children should never be left unattended in the car. • Movement of the seat can be STOPPED at any time by pressing any button on the power seat control panel. • Do not adjust the seat while driving. The seat should be adjusted so that the brake pedal can be depressed fully. In addition, position the seat as far rear- ward as comfort and control allow. • The seat rails on the floor must not be obstructed in any way when the seat is in motion. 04 Interior Front seats Adjusting the front seat head restraints The head restraints should be put in the upper or lower position according to the height of the occupant of the seat. The front seat head restraints are designed so that they can be adjusted to two different height positions. NOTE • When the vehicle leaves the factory, the front seat head restraints will be in the lower position. • It is advisable to have the front seat head restraints in the lower position if you wish to fold down the seat's back- rest. The upper edge of the head restraint should be at least on a level with the upper-most point of the seat occupant's ear (see illustration). To raise or lower a head restraint: Raising or lowering a head restraint 1. Release the head restraint by pressing the button underneath its left side, at the base of the support (see the illustration). 2. Move the head restraint until it clicks (locks) into the upper or lower position. 04 111 04 Interior Front seats WARNING After adjusting the head restraint, be sure that it is securely locked in the new position by pressing and/or pulling it. Removing a head restraint The front seat head restraints can be removed, for example, when cleaning the upholstery or if the front passenger's seat backrest is folded down to accommodate a long load. To do so: 1. Release the head restraint by pressing the release button underneath its left side, at the base of the support. 2. While holding in the release button, press the locking button at the base of the head restraint's right support with a screw driver, etc., and lift the head restraint until it can be removed completely. WARNING • If a front seat head restraint has been removed, it must be put properly back in place and it must lock (click) into one of the available adjustment positions before the seat is occupied. • The front seat head restraints must be in position and properly adjusted to the height of the person sitting in the seat when the vehicle is driven and when the front passenger's seat is occupied. 04 112 04 Interior Interior lighting Interior lighting – Neutral position: the interior courtesy light- ing comes on when a door is opened, and is switched off 10 seconds after the door is closed. – Press the right side of the button: the inte- rior courtesy lighting stays off. 5 minutes after the engine has been switched off. Footwell lighting The footwell (and courtesy lighting) comes on or goes off when one of the side doors is opened or closed. Front courtesy lights and reading lights Front driver's side reading light, on/off Courtesy lighting Front passenger's side reading light, on/off The front seat reading lights can be switched on and off by pressing buttons (1) or (3) when the ignition key is in position I or II, or when the engine is running. The courtesy lighting (2) can be set to three positions: – Press the left side of the button: the interior courtesy lighting turns on. Courtesy lighting – automatic function The interior lighting has a built-in automatic function that switches on the courtesy lighting for 30 seconds when: • the car is unlocked from the outside using the key blade or remote key • the engine is switched off and the ignition key is turned to the 0 position. The courtesy lighting lights up or remains on for 5 minutes when: • one of the doors is opened and left open. • the courtesy lighting has not been switched off (the right side of button 2 depressed). The automatic lighting goes out when: • the engine is started • the car is locked from the outside using the key blade or remote key. If the courtesy lighting is not switched off man- ually, it will be turned off automatically Vanity mirror Raise the cover to switch on the light. 04 113 04 Interior Storage compartments 04 114 Compartment on rear side of front seat backrests Compartment in door panel Storage pocket (on the front side of the front seat cushion, depending on choice of upholstery) Glove compartment Storage compartment for e.g., CDs and cup holders Compartment in rear side panels, with space for up to three beverage cans WARNING • Anchor any heavy objects to prevent them from moving during sudden stops. 04 Interior Storage compartments Glove compartment Storage under the front, center armrest 04 The owners manual and maps can be stored here. There are also holders for coins, pens and fuel cards. The glove compartment can only be locked and unlocked using the detachable key blade from the central locking system's remote key. See page 128 for information on removing the key blade from the remote key, and page 136 for information about locking the glove compartment. There are two storage compartments under the front, center armrest. • Press the smaller button on the front edge of the armrest and lift the armrest cover to access a shallow storage compartment. • Press the larger button and lift the entire armrest to access a deeper compartment. 115 04 Interior Storage compartments CD storage Cup holders in the center console Storage compartment behind the gear lever 04 116 The deep storage compartment has room for 10 CD jewel cases. These cases must be inserted with their spines upward in order to allow space for 10 cases in the storage com- partment Two cup holders are located under the sliding cover in the center console. The cup holders can be lifted out if necessary. To do so, grasp the indentation on the rear edge of the cup holder and lift. To put the cup holder back in place: 1. Slide the two locating tabs in the front side of the cup holder into the two correspond- ing recesses in the center console storage space. 2. Press down the rear edge of the cup holder. To close the sliding cover, grasp the underside of the front edge and pull. If the buttons for optional equipment are not installed, the recess behind the gear lever can be used as a storage compartment for coins, etc. Rear seat head restraints – – Adjust the head restraint vertically Both of the rear seating positions are equipped with a head restraint that can be adjusted ver- tically to two different positions to help suit the height of the passenger. The upper edge of the head restraint should be at least on a level with the upper-most point of the seat occupant's ear (see illustration). – To raise: Slide the head restraint up to the desired height. To lower: Press the catch at the base of the right support and press the head restraint down. To remove: Pull the head restraint up far as possible. Press the catch at the base of the right support and pull the head restraint out of the its holders. WARNING If a head restraint has been removed, it must be put properly back in place and it must lock (click) into one of the available adjust- ment positions before the seat is occupied. 04 Interior Rear seat Folding down the rear seat backrests 04 CAUTION • When the backrests are folded down, the head restraints may be damaged if they are not removed. • To help prevent damage to the uphols- tery when the backrest is folded down, be sure that there are no objects on the seat and that the seat belt is not buck- led. Both sections of the rear seat backrest can be folded down, together or separately, to enable you to transport long objects. 117 04 Interior Rear seat To fold down one or both sections: 1. Pull the catch on the upper outboard edge of the backrest upward and forward to release the backrest lock. A red lock indi- cator (A) is visible when the backrest is not locked in the upright position. 2. Fold the backrest down. WARNING • The red lock indicator is VISIBLE when the backrest is NOT locked in position and hidden when the backrest is cor- rectly locked in place. When the back- rest is in the upright position, push and pull it to make sure that it is correctly locked in place. • When the rear seat is folded down, do not place heavy objects against the backs of the front seats. This places a severe strain on the folded down back- rest of the rear seat. Be sure to secure cargo. • Cargo must not be stacked higher than the top of seat backs. This will reduce the possibility of luggage, etc. becom- ing projectiles during sudden maneu- vers, rapid braking or an accident. Rear seat armrest The space between the rear seats can be used for transporting long objects. WARNING • The center of the rear seat is not a seat- ing position. This space is not equipped with a seat belt or ISOFIX anchors. No one should attempt to sit in this position and child seats should never be placed in the center of the rear seat. • The rear seat center armrest is fixed in the folded down position and cannot be folded up. 04 118 WARNING Long loads should be securely anchored. 04 Interior Rear seat 04 119 04 Interior Cargo area Load anchoring eyelets Hard cargo area cover* 04 The eyelets in the cargo area can be used to fasten accessory load nets and lashing straps, load nets, and other load anchors. Installing the cargo area cover 1. Before lifting cover into the vehicle, retract all four lock pins by pulling back the lock buttons as far as possible. The pins will remain retracted. 2. Lift the cover into the vehicle at an angle, turn it back and raise the front edge slightly. 3. Place the front section of the cover on the two support pins behind the locking points (A) on both sides of the vehicle. 4. Place one of the rear locks at (B) and slide the lock pin into position by moving the lock button forward. 5. Put the other rear lock into position in the same way and slide the lock pin into posi- tion by moving the lock button forward. 6. Slide the front lock buttons forward, one at a time, so that the lock pins move into position (A). NOTE The rear section of the cover can be folded up when loading items into the cargo area. 120 * Option/accessory, for more information, see Introduction. WARNING The cargo area cover does not have a load anchoring function. No item should be place on top of the cargo area cover. These items could move forward and cause injury during braking. Removing the cover 1. Retract the front lock pins at (A) by pulling back the lock buttons on both sides as far as possible. 2. Retract the rear lock pins at (B) by pulling back the lock buttons on both sides as far as possible. 3. Lift up and turn the cover before lifting it out of the vehicle. Soft cargo area cover* 04 Interior Cargo area 4. Attach the rear lower hooks on the cover to the lower eyelets (D) on opposite sides of the vehicle. Hanging the cover when it is not in use 1. Remove the rear hooks (D) from the eye- lets. 2. Press together the rear rails (C) and remove them from their attachments. Place them at the front of the cargo area floor. 3. Attach the hooks in the rail next to the attachments (B). 04 The cargo area cover is now hanging near the rear seat backrests until it is needed again. The cargo area cover is pulled over the cargo area and fastened to the eyelets with the hooks on the corners of the cover. 2. Installing the cover 1. Attach the front lower hooks on the cover to the lower eyelets (A) on opposite sides of the vehicle. Insert the front upper attachments (B) by pressing together the spring-loaded rails and pressing them into place on opposite sides of the vehicle. Insert the upper rear rails (C) in the same way. 3. Removing the cargo area cover 1. Remove the hooks and remove the rails one at a time by pressing them together and removing them from their attach- ments. 2. When all attachments have been removed, the cover can be rolled up and placed on the rear part of the cargo area floor to make room for cargo. * Option/accessory, for more information, see Introduction. 121 04 Interior Cargo area WARNING The cargo area cover does not have a load anchoring function. No item should be place on top of the cargo area cover. These items could move forward and cause injury during braking. Cargo area net* 04 Installing the net 1. Fold down the rear seat backrests (see page 117). 2. Attach the cargo net to the upper mounting brackets near the ceiling. 3. Attach the cargo net’s hooks in the eyelets near the seat belts floor anchorages on opposite sides of the vehicle. 4. Pull the cargo net’s bands taut if neces- sary. WARNING • Be sure that the net is securely attached in the mounting brackets and eyelets. • Cargo should be properly secured even when the net is in use. Removing the cargo net 1. Release the pressure on the bands. 2. Remove the hooks from the eyelets near the floor. The cargo area net can be placed behind the front seat backrests.This net is only intended to be used when the rear seat backrests are folded down. 3. Remove the net from the ceiling mounting brackets. 4. Fold the net and keep it in its storage bag. 122 * Option/accessory, for more information, see Introduction. Folding up the cargo area floor hatch Without the cargo area cover Fold up the hatch and attach it to the latches on both sides of the cargo area. With the hard cover in place 1. Fold up the hatch on the cargo area cover. 2. Fold up the floor hatch and fasten it to the hook on the underside of the cargo area cover. 04 Interior 04 123 Remote key and key blade................................................................... 126 Keyless drive*........................................................................................ 131 Locking and unlocking.......................................................................... 135 Alarm..................................................................................................... 137 124 * Option/accessory, for more information, see Introduction. LOCKS AND ALARM 05 Locks and alarm Remote key and key blade Remote keys Two remote keys that also function as ignition keys are provided with your car. The remote keys contain detachable metal key blades for manually locking or unlocking the driver's door and the glove compartment. USA – FCC ID: LTQVO315TX This device complies with part 15 of the FCC rules. Operation is subject to the following con- ditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interfer- ence that may cause undesired operation. Canada – IC: 3659AVO315TX Operation is subject to the following condi- tions: (1) this device may not cause interfer- ence, and (2) this device must accept any inter- ference, including interference that may cause undesired operation of the device. Loss of a remote key If either of the remote keys is lost, the other should be taken with the car to a Volvo retailer. As an anti-theft measure, the code of the lost remote key must be erased from the system. 05 126 NOTE Additional or duplicate remote control keys can be obtained from any Authorized Volvo Retailer. You can also obtain additional or duplicate remote control keys from certain independ- ent repair facilities and locksmiths that are qualified to make remote control keys. Each key must be programmed to work with your vehicle. California Only: A list of independent repair facilities and/or locksmiths known to Volvo that can cut and code replacement keys can be found: • on the Volvo website at http://www.volvocars.com/us/keys • by calling Volvo Customer Care at 1-800-458-1552 Each key blade has a unique code, which is used if new key blades are required. A maxi- mum of six remote keys/key blades can be programmed and used for one car. Immobilizer (start inhibitor) Each of the keys supplied with your car con- tains a coded transponder. The code in the key is transmitted to an antenna in the ignition switch where it is compared to the code stored in the start inhibitor module. The car will start only with a properly coded key. If you misplace a key, take the other keys to an authorized Volvo retailer for reprogramming as an antitheft measure. CAUTION Never use force on the narrow section of the remote key – this is where the transponder is located. The car cannot be started if the transponder is damaged. USA – FCC ID: LTQWFS 125VO This device complies with part 15 of the FCC rules. Operation is subject to the following con- dition: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interfer- ence that may cause undesired operation. Canada – IC: 3659A-WFS125VO Operation is subject to the following condi- tions: (1) this device may not cause interfer- ence, and (2) this device must accept any inter- ference, including interference that may cause undesired operation of the device. Remote key functions Lock – Press the Lock button on the remote once to lock all doors and the lift- gate. The turn signals will flash once to confirm locking. NOTE The car can also be locked if a door is open (does not apply to vehicles with the optional keyless drive). 05 Locks and alarm Remote key and key blade Unlock – Press the Unlock button on the remote once to unlock the driver's door. After a short pause, press the Unlock but- ton a second time within 10 seconds to unlock the other doors and the liftgate. A long press (at least several seconds) opens all side windows. 2 minutes unless a door or the liftgate has been opened. • Automatic locking: When the car starts to move, the doors and liftgate can be locked automatically. This feature can be turned on or off, see Personal settings on page 84 for more information. NOTE • The turn signals flash to confirm that the vehicle has been correctly locked/ unlocked with the remote key or the optional keyless drive. When locking the vehicle, the turn signals will flash a con- firmation only if all the doors are securely closed and locked. Flashing confirmation for locking and unlocking may be customized in the vehicle's Per- sonal settings menu, see page 84 for more information. • The two-step unlocking function can be changed so that one press of the Unlock button unlocks both doors and the liftgate. See Personal settings page 84 for more information. • Automatic relocking: If the doors are unlocked, the locks will automatically reen- gage (re-lock) and the alarm will rearm after • Airbag deployment will automatically attempt to unlock the doors. Approach lighting – As you approach the car: Press the button on the remote key to illuminate the area around the car in dark conditions. Pressing the button once lights up the interior lighting, parking lights, and license plate lighting. These lights will switch off automatically after 30, 60 or 90 seconds. See the Personal settings page 84 for information about adjusting the time setting. Unlock liftgate – Press the button once to disarm the alarm system and unlock only the liftgate. After closing, the liftgate will not automatically relock. Press Lock to relock it and rearm the alarm. NOTE This function will not open the liftgate. 05 127 05 Locks and alarm Remote key and key blade Panic alarm – This button can be used to attract attention during emergency situa- tions. To activate the panic alarm, press and hold the red button for at least 3 sec- onds or press it twice within 3 seconds. The turn signals and horn will be activated. The panic alarm will stop automatically after 30 seconds. To deactivate, wait approximately 5 seconds and press the red button again. NOTE This button will NOT unlock the car. 05 Weak battery in the remote key When the battery begins to lose its charge, the Information symbol in the instrument panel (see page 56) lights up and KEY BATTERY LOW VOLTAGE is shown in the information display. Replacing the battery in the remote key If the range of the transmitter is noticeably reduced, this indicates that the battery (type CR 2450, 3V) is weak and should be replaced. To replace the battery: 1. Place the remote key with the keypad downward. Pry open the cover with a small slotted screwdriver. 2. Remove the cover. CAUTION When replacing the battery, avoid touching the electrical circuitry in the other half of the remote key. 3. Note how the + and – sides of the battery are positioned on the inside of the cover (see the underside of the cover). 4. Pry out and replace the battery. Avoid touching the battery and its contact surfa- ces with your fingers. 5. Press the cover back into place. 128 The old battery should be disposed of properly at a recycling center or by a trained and quali- fied Volvo service technician. Key blade Removing the key blade The key blade can be removed from the remote key. When removed, it can be used as follows: • To lock/unlock the driver’s door • To lock/unlock the glove compartment, see page 136. Removing the key blade Slide the spring loaded catch to the side. Locking the doors with the detached key blade 1. Lock the other door(s) by pressing the lock button on each door. Please note that this does not arm the alarm or lock the liftgate. 2. Turn the key blade one-quarter turn coun- ter-clockwise to lock the driver's door. Locking points By utilizing the remote key with the key blade removed, you can block access to the glove compartment for e.g. valet parking or when the car is brought to the retailer for service. While holding the catch, pull the key blade out of the remote key. Reinserting the key blade in the remote key 1. Hold the remote key with the pointed end down. 2. Carefully slide the key blade into its groove. 3. Gently press the key blade in the groove until it clicks into place. Unlocking the doors with the detached key blade 1. Insert the key blade as far as possible in the driver's door lock. 2. Turn the key blade clockwise approxi- mately one-quarter turn to unlock the driv- er's door only. NOTE After unlocking the driver's door with the key blade, opening the door will trigger the alarm. To disable the alarm Press the Unlock button on the remote key, or insert the key in the ignition switch. 05 Locks and alarm Remote key and key blade 05 129 05 Locks and alarm Remote key and key blade 05 Locking/unlocking points for the remote key with the key blade Locking/unlocking points for the remote key without the key blade 130 Keyless locking and unlocking Range of the keyless drive remote key–5 ft (1.5 meters) This system makes it possible to unlock and lock the vehicle without having to use the remote key. It is only necessary to have a key- less drive remote key in your possession to operate the central locking system. NOTE The buttons on the keyless drive remote key can also be used to lock and unlock the vehicle, see page 127 for more information. Both of the remote keys provided with the vehi- cle have the keyless function, and additional remotes can be ordered. The system can accommodate up to six keyless drive remote keys. NOTE The number of doors that are unlocked at the same time can be set in the Personal settings menu, see page 84 for additional information. Unlocking the vehicle • A keyless drive remote key must be on the same side of the vehicle as the door to be opened, and be within 5 feet (1.5 meters) of the lock or the liftgate opening control (see the shaded areas in the illustration). • Pull a door handle to unlock and open the door or press the liftgate opening control on the liftgate. • See page 152 for information on starting a vehicle equipped with keyless drive. 05 Locks and alarm Keyless drive* Locking the vehicle Keyless drive lock button The doors and the liftgate can be locked by pressing the lock button in any of the outside door handles. 05 NOTE • If one or more doors and/or the liftgate is not fully closed when the lock button is pressed, the door(s) or liftgate will not be locked. • On keyless drive vehicles with an auto- matic transmission, the gear selector must be in the Park (P) position and the ignition must be switched off before the doors/liftgate can be locked. * Option/accessory, for more information, see Introduction. 131 05 Locks and alarm Keyless drive* Locking or unlocking the vehicle with the key blade 05 Keyless drive keyhole cover The driver's door on vehicles equipped with keyless drive can be locked or unlocked with the remote key's detachable key blade if nec- essary, see page 128 for information on remov- ing the key blade from the remote key. To access the keyhole in the driver's door: • Pry off the keyhole cover by inserting the key blade or a small screwdriver in the hole on the underside of the cover (indicated by the arrow in the inset illustration). • Insert the key blade as far as possible in the driver's door lock. Turn the key blade clockwise approximately one-quarter turn to unlock the driver's door only. This will trigger the alarm. • To disable the alarm: Press the Unlock button on the keyless drive remote key. If the batteries in the remote are weak, remove the keyless drive start control from the ignition switch by pressing the catch (see the illustration on page 152) and pull- ing the control out of the ignition switch. Insert the ignition key section of a keyless drive remote key in the ignition switch. Keyless drive remote key and driver's seat memory This function is only available on vehicles equipped with the optional power driver's seat. • When you leave the car with a keyless drive remote key in your possession and lock any door, the position of the driver's seat will be stored in the seat's memory. • The next time a door is opened by a person with the same remote key in his/her pos- session, the driver's seat will automatically move to the position that it was in when the door was most recently locked. NOTE If several people carrying keyless drive remote keys approach the vehicle at the same time, the driver's seat will assume the position it was in for the person who opens a door first. Keyless drive information messages If anyone leaves the vehicle with the only key- less drive remote key in his or her possession while the ignition is switched on, a message will be shown in the information display and an audible signal will sound. NOTE This message will only be displayed if the start control is in position I or II. The message will be erased from the display and the audible signal will stop when the remote key has been returned to the vehicle and one of the following has occurred: • A door has been opened and closed • The start control has been turned to posi- tion 0 • The READ button (see page 61 for the location of this button) has been pressed. 132 * Option/accessory, for more information, see Introduction. KR55WK48964 NOTE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including inter- ference that may cause undesired operation. CAUTION Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Siemens VDO 5WK48891 Tested To Comply With FCC Standards For Automobile Use Location of the keyless drive antennas The keyless drive system has a number of antennas located at various points in the vehi- cle. CAUTION • Keyless drive remote keys should never be left in the vehicle. In the event of a break-in, a remote found in the vehicle could make it possible to start the engine. • Electromagnetic fields or metal obstructions can interfere with the key- less drive system. The remote key should never be placed closer than approximately 4-6 in. (10-15 cm) to cell phones, metallic objects or e.g., stored in a metal briefcase. Canada – IC:267T- 5WK48952, 267T- 5WK48964, 267T-5WK48891 NOTE This device complies with RSS -210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including inter- ference that may cause undesired operation. CAUTION Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. USA – FCC ID:KR55WK48952, 05 Locks and alarm Keyless drive* On the inside center of the rear bumper 05 Under the floor of the cargo area, near the rear seat Left door handle Under the rear section of the center con- sole Right door handle Under the front section of the center con- sole * Option/accessory, for more information, see Introduction. 133 05 Locks and alarm Keyless drive* WARNING People with implanted pacemakers should not allow the pacemaker to come closer than 9 inches (22 cm) to any of the keyless drive system's antennas. This is to help pre- vent interference between the pacemaker and the keylesss drive system. 05 134 * Option/accessory, for more information, see Introduction. Locking/unlocking the vehicle from the inside The switch near the door opening handle on the driver's door can be used to lock or unlock both doors and the liftgate, open the windows in the doors1, and to set the alarm. – Unlocking: Press the upper section of the switch. A long press (for several seconds) also opens the windows in the doors. Locking: Press the lower section of the switch. – Alternative locking when parking The central locking button on the driver's door can also be used to lock the vehicle when you leave it. To do so: 1. Open the door. 2. Press the lock section of the button. 3. Close the door. This will lock the vehicle completely and arm the alarm. NOTE Please be aware that locking the vehicle in this way makes it possible to lock the remote key in the passenger compartment. To help avoid this, lock the vehicle from the outside by pressing the lock button on the remote key. If the vehicle is locked using the central locking button, be sure that the remote key is in your possession before closing the door. 1 This function must be set to On in the Personal settings menu (see page 85) 05 Locks and alarm Locking and unlocking NOTE • The ignition key must be in position I or higher (see page 149) before the win- dows in the doors can be opened using the switches in the front doors. • The doors cannot be opened by pulling up the lock buttons. • If both doors are closed when a lock button is pressed, the alarm will not be armed. • Each door can also be locked manually using the lock button on that particular door. This applies only if the car has not been locked from the outside. • The doors can also be unlocked (and the door opened) by pulling the handle in the door twice. 05 135 05 Locks and alarm Locking and unlocking Locking the glove compartment The glove compartment can only be locked and unlocked using the detachable key blade on the remote key, see page 128 for informa- tion on removing the key blade from the remote key. Insert the key blade in the glove compart- ment lock. Turn the key blade 90 degrees clockwise.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2013 Volvo C30 Owners Manual