2013 Volvo C30 Owners Manual

Download PDF Manual
warranties. Periodic maintenance helps minimize emissions Periodic maintenance will help keep your vehi- cle running well. Your Warranty and Service Records Information booklet provides a com- prehensive periodic maintenance schedule up to 150,000 miles (240,000 km) of vehicle main- tenance. The schedule includes components that affect vehicle emissions. This page describes some of the emission-related com- ponents. 09 Maintenance and servicing Maintaining your car 09 As needed: • Wash the car, including the undercarriage, to reduce wear that can be caused by a buildup of dirt, and corrosion that can be caused by salt residues. • Clean leaves and twigs from air intake vents at the base of the windshield, and from other places where they may collect. NOTE Complete service information for qualified technicians is available online for purchase or subscription at www.volvotechinfo.com. Hoisting the vehicle Owner maintenance Periodic maintenance requirements and inter- vals are described in your vehicle's Warranty and Service Records Information booklet. The following points can be carried out between the normally scheduled maintenance services. Each time the car is refueled: • Check the engine oil level. • Clean the windshield, windshield wipers, headlights, and taillights. Monthly: • Check cold tire pressure in all tires. Inspect the tires for wear. • Check that engine coolant and other fluid levels are between the indicated "min" and "max" markings. • Clean interior glass surfaces with a glass cleaner and soft paper towels. • Wipe driver information displays with a soft cloth. • Visually inspect battery terminals for cor- rosion. Corrosion may indicate a loose ter- minal connector, or a battery near the end of its useful service life. Consult a trained and qualified Volvo service technician for additional information. If a garage jack is used to lift the vehicle, the two jack attachments points should be used. They are specially reinforced to bear the weight of the vehicle. A garage jack can also be placed under the front of the engine support frame. Take care not to damage the splash guard under the engine. Ensure that the jack is posi- tioned so that the vehicle cannot slide off it. Always use axle stands or similar structures. If a two-post hoist is used to lift the vehicle, the front and rear lift arm pads should be centered under the reinforced lift plates on the inboard edge of the sill rail (see illustration). Emission inspection readiness What is an Onboard Diagnostic System (OBD II)? OBD II is part of your vehicle's computerized engine management system. It stores diagnos- tic information about your vehicle's emission controls. It can light the Check Engine light (MIL) if it detects an emission control "fault." A "fault" is a component or system that is not performing within an expected range. A fault may be permanent or temporary. OBD II will store a message about any fault. 217 09 Maintenance and servicing 09 Maintaining your car your vehicle diagnosed and, if necessary, serviced by a qualified Volvo technician. • If you recently had service for a lit Check Engine light, or if you had service that required disconnecting the battery, a period of driving is necessary to bring the OBD II system to "ready" for inspection. A half-hour trip of mixed stop-and-go/high- way driving is typically needed to allow OBD II to reach readiness. Your Volvo retailer can provide you with more infor- mation on planning a trip. • Maintain your vehicle in accordance with your vehicle's maintenance schedule. How Do States Use OBD II for Emission Inspections? Many states connect a computer directly to a vehicle's OBD II system. The inspector can then read "faults." In some states, this type of inspection has replaced the tailpipe emission test. How Can My Vehicle Fail OBD II Emission Inspection? Your vehicle can fail OBD II emission inspec- tion for any of the following reasons. • If your Check Engine (MIL) light is lit, your vehicle may fail inspection. • If your vehicle's Check Engine light was lit, but went out without any action on your part, OBD II will still have a recorded fault. Your vehicle may pass or fail, depending on the inspection practices in your area. • If you had recent service that required dis- connecting the battery, OBD II diagnostic information may be incomplete and "not ready" for inspection. A vehicle that is not ready may fail inspection. How Can I Prepare for My Next OBD II Emission Inspection? • If your Check Engine (MIL) light is lit – or was lit but went out without service, have 218 Opening the hood To open the hood: 1. Pull the lever located under the left side of the dash to release the hood lock. 2. Lift the hood slightly. 3. Press up the release control located under the front edge of the hood (at the center) up to the right, and lift the hood. WARNING Check that the hood locks engage properly when closed. 09 Maintenance and servicing Hood 09 219 09 Maintenance and servicing 09 Engine compartment WARNING The cooling fan (located at the front of the engine compartment, behind the radiator) may start or continue to operate (for up to 6 minutes) after the engine has been switched off. Cooling system expansion tank Power steering fluid reservoir (concealed behind the headlight) Dipstick – engine oil Washer fluid reservoir Engine oil filler cap Brake/clutch fluid reservoir Battery Relay/fuse box 220 Changing engine oil and oil filter See page 279 for oil specifications. Refer to the Warranty and Service Records Information booklet for information on the oil change inter- vals. NOTE • Volvo does not recommend the use of oil additives. • Synthetic oil is not used when the oil is changed at the normal maintenance intervals except at owner request and at additional charge. Please consult a trained and qualified Volvo service tech- nician. Checking and adding oil The oil level should be checked at regular inter- vals, particularly during the period up to the first scheduled maintenance service. • The car should be parked on a level surface when the oil is checked. • If the engine is warm, wait for at least 10–15 minutes after the engine has been switched off before checking the oil. 09 Maintenance and servicing Engine oil 09 Checking the oil 1. Pull out the dipstick and wipe it with a lint- free rag. 2. Reinsert the dipstick, pull it out, and check the oil level. 3. Add oil if necessary. If the level is close to the MIN mark, add approximately 0.5 US quarts (0.5 liters) of oil. 4. Recheck the level and add more oil if nec- essary until the level is near the MAX mark. Location of dipstick and oil filler cap Volvo recommends Castrol oil products 221 09 Maintenance and servicing 09 Engine oil CAUTION NOTE Volvo uses different systems to indicate a low oil level or pressure. Some models have an oil pressure sensor, in which case a warning symbol (see page 58) is used to indicate low oil pressure. Other models have an oil level sensor, in which case the driver is alerted by the warning symbol in the cen- ter of the instrument panel and a text in the information display. Some models use both systems. Contact an authorized Volvo retailer for more information. • Not checking the oil level regularly can result in serious engine damage if the oil level becomes too low. • Oil that is lower than the specified qual- ity can damage the engine. • Always add oil of the same type and viscosity as already used. • Never fill oil above the MAX mark. This could cause an increase in oil consump- tion. • Oil changes should be carried out by a trained and qualified Volvo service tech- nician. WARNING Do not allow oil to spill onto or come into contact with hot exhaust pipe surfaces 222 09 Maintenance and servicing Fluids 09 Washer fluid Coolant Washer fluid reservoir The washer fluid reservoir is located in the engine compartment and holds approximately 4.2 US qts (4 liters). During cold weather, the reservoir should be filled with windshield washer solvent containing antifreeze. Coolant reservoir Normally, the coolant does not need to be changed. If the system must be drained, con- sult a trained and qualified Volvo service tech- nician. CAUTION • If necessary, top up the cooling system with Volvo Genuine Coolant/Antifreeze only (a 50/50 mix of water and anti- freeze). • Different types of antifreeze/coolant may not be mixed. • If the cooling system is drained, it should be flushed with clean water or premixed anti-freeze before it is refilled with the correct mixture of water/anti- freeze. • The cooling system must always be kept filled to the correct level, and the level must be between the MIN and MAX marks. If it is not kept filled, there can be high local temperatures in the engine which could result in damage. Check coolant regularly! • Do not top up with water only. This reduces the rust-protective and anti- freeze qualities of the coolant and has a lower boiling point. It can also cause damage to the cooling system if it should freeze. • Do not use chlorinated tap water in the vehicle's cooling system. 223 09 Maintenance and servicing 09 Fluids WARNING • Never remove the expansion tank cap while the engine is warm. Wait until the engine cools. • If it is necessary to top off the coolant when the engine is warm, unscrew the expansion tank cap slowly so that the overpressure dissipates. Brake fluid Power steering fluid The fluid level is checked at each service inter- val. Fluid type: Volvo power steering fluid or equiv- alent. Replace: No fluid change required. WARNING If a problem should occur in the power steering system or if the vehicle has no elec- trical current and must be towed, it is still possible to steer the vehicle. However, keep in mind that greater effort will be required to turn the steering wheel. Fluid type: DOT 4+ boiling point >536 °F (>280 °C), P/N 9437433 Replace: The fluid should be replaced accord- ing to the intervals specified in the Warranty and Service Records Information booklet. When driving under extremely hard conditions (mountain driving, etc), it may be necessary to replace the fluid more often. Consult your Volvo retailer. Always entrust brake fluid changing to a trained and qualified Volvo serv- ice technician. WARNING • If the fluid level is below the MIN mark in the reservoir or if a brake-related message is shown in the information display: DO NOT DRIVE. Have the car towed to a trained and qualified Volvo service technician and have the brake system inspected. • Dot 4+ should never be mixed with any other type of brake fluid. Brake fluid reservoir The brake fluid should always be between the MIN and MAX marks on the side of the reser- voir. Check, without removing the cap, that there is sufficient fluid in the reservoir. 224 Replacing windshield wiper blades Liftgate wiper blade 09 Maintenance and servicing Wiper blades 09 1. Fold out the wiper arm. 2. Press the button on the wiper blade attach- ment and pull straight out (1), parallel with the wiper arm. 3. Press a new wiper blade (2) until it clicks into place. 4. Ensure the blade is securely attached (3). 5. Fold in the wiper arm. The wiper blades are different lengths. The blade on the driver's side is longer than the one on the passenger's side. 1. Fold out the wiper arm. 2. Remove the wiper blade by pulling it straight out from the wiper arm. 3. Press the new wiper blade securely into place. Fold in the wiper arm. Keeping the windshield/liftgate window and wiper blades clean helps improve visibility and prolongs the service life of the wiper blades. See page 208 for washing instructions. 225 09 Maintenance and servicing 09 Battery • To help keep the battery in good condition, the vehicle should be driven for at least 15 minutes a week or connected to a charger with an automatic charging function. • If the battery is fully discharged a number of times, this may shorten its service life. Keeping the battery fully charged helps prolong its service life. • The service life of a battery is affected by factors such as driving conditions and cli- mate. Extreme cold may also further decrease the battery’s starting capacity. • Because the battery’s starting capacity decreases with time, it may be necessary to recharge it if the vehicle is not driven for an extended period of time or if the vehicle is usually only driven short distances. • WARNING PROPOSITION 65 WARNING! Battery posts, terminals, and related acces- sories contain lead and lead compounds, chemicals known to the state of California to cause cancer and reproductive harm. Wash hands after handling. Battery symbols Wear protection goggles See owner’s manual for details Keep away from children Corrosive Battery maintenance Driving habits and conditions, climate, the number of starts, etc., all affect the service life and function of the battery. In order for your battery to perform satisfactorily, keep the fol- lowing in mind: Check the fluid level in each cell in the battery every 24 months or every 15,0001 miles (24,000 km), whichever is sooner. • Use a screw driver to open the caps or cover and a flashlight to inspect the level. • If necessary, add distilled water. The level should never be above the indicator. • The fluid level should be checked if the battery has been recharged. • After inspection, be sure the cap over each battery cell or the cover is securely in place. • Check that the battery cables are correctly connected and properly tightened. • Never disconnect the battery when the engine is running, or when the key is in the ignition. This could damage the vehicle's electrical system. • The battery should be disconnected from the vehicle when a battery charger is used directly on the battery. 1 More frequently in warm climates. 226 09 Maintenance and servicing Battery 09 No smoking, no open flames, no sparks Explosion Recycle properly 4. Disconnect the battery negative (ground) cable. 5. Disconnect the positive cable. 6. Remove the front side of the battery box with a screwdriver. 7. Release the clamp holding the battery. 8. Lift out the battery. Installing a new battery 1. Put the battery in place in the engine com- partment. Install the battery's retaining clamp. 2. 3. Reinstall the front side of the battery box. 4. Connect the positive cable. 5. Connect the ground cable. 6. Reinstall the cover over the battery. WARNING • Never expose the battery to open flame or electric spark. • Do not smoke near the battery. • Battery fluid contains sulfuric acid. Do not allow battery fluid to contact eyes, skin, fabrics or painted surfaces. If con- tact occurs, flush the affected area immediately with water. Obtain medical help immediately if eyes are affected. Battery replacement NOTE Used batteries should be properly disposed of at a recycling station or similar facility, or taken to your Volvo retailer. Removing the battery 1. Switch off the ignition and remove the key. 2. Wait at least 5 minutes after switching off the ignition before disconnecting the bat- tery so that all information in the vehicle's electrical system can be stored in the con- trol modules. 3. Remove the cover over the battery. 227 09 Maintenance and servicing 09 Replacing bulbs Removing the headlight housing WARNING • The engine should not be running when changing bulbs. • If the engine has been running just prior to replacing bulbs in the headlight hous- ing, please keep in mind that compo- nents in the engine compartment will be hot. WARNING Active Bending Lights* – due to the high voltage used by these headlights, these bulbs should only be replaced by a trained and qualified Volvo service technician. Introduction Before replacing bulbs in your vehicle, please keep the following points in mind: NOTE Never touch the glass of bulbs with your fin- gers. Grease and oils from your fingers vaporize in the heat and will leave a deposit on the reflector, which will damage it. The optional Active Bending Light bulbs contain trace amounts of mercury. These bulbs should always be disposed of by a trained and qualified Volvo service techni- cian. Certain bulbs should only be replaced by a trained and qualified Volvo service techni- cian: • Courtesy lighting • Reading lights • Glove compartment lights • Turn signals and courtesy lights in the side door mirrors • High-mounted brake lights • Active Bending Lights, Brake lights See page 234 for a list of bulb specifications. 228 * Option/accessory, for more information, see Introduction. The entire headlight housing must be lifted out when replacing the high/low beam, parking light, turn signal, and side marker bulbs. To lift out the housing: 1. Remove the key from the ignition and turn the headlight switch to position 2. Open the hood. 3. Pull up the headlight housing's retaining pin. 4. Pull out the headlight housing. 09 Maintenance and servicing Replacing bulbs 09 Low beam bulb 5. Disconnect the wiring connector by press- ing down the clip with your thumb while at the same time pulling the connector with your other hand. 6. Lift out the headlight housing and place it on a soft surface to avoid scratching the lens. CAUTION When disconnecting the connector, pull on the connector itself and not on the wiring. After the defective bulb has been replaced, reinsert the housing in the reverse order. Check that the retaining pin is correctly inserted. Cover with retaining clamps 1. Open the hood and remove the headlight housing (see page 228 for instructions). 2. Release the retaining clamps on the cover and remove it. 3. Release the bulb's retaining spring holding the bulb in place by pressing it first to the left to release it and then moving it outward and downward. 4. Pull out the bulb. Low beam bulb Installing a new bulb 1. Insert the new bulb. It can only be installed in one position. 2. Press the retaining spring inward and upward and slightly to the right until it snaps into place. 3. Press the wiring connector onto the bulb. 4. Put the plastic cover in place. 5. Press the retaining clamps back into place. 6. Reinstall the headlight housing (see page 228). 229 09 Maintenance and servicing 09 Replacing bulbs High beam bulb Halogen high beam bulb 1. Open the hood. 2. Remove the headlight housing (see page 228). NOTE The halogen high beam bulb has a different socket on vehicles equipped with the optional Active Bending Lights. On these models, pull the bulb straight out. WARNING Active Bending Lights* – due to the high voltage used by these headlights, the Active Bending Light bulbs should only be replaced by a trained and qualified Volvo service technician. 3. Driver's side headlight: Turn the bulb holder counterclockwise. Passenger's side headlight: Turn the bulb holder clockwise. 4. Pull out the bulb holder and replace the bulb. 5. Reinstall the bulb holder. It can only be installed in one position. 6. Reinstall the headlight housing (see page 228). Parking light bulb 1. Turn the bulb holder counterclockwise, pull it out and replace the bulb. 2. Press the bulb holder back into place. It can only be installed in one position. NOTE Vehicles equipped with the optional Active Bending Lights (headlights) have LED park- ing lights that cannot be replaced. 230 * Option/accessory, for more information, see Introduction. Turn signal Side marker light Front fog lights* 09 Maintenance and servicing Replacing bulbs 09 1. Turn the bulb holder counterclockwise and remove it. 2. Remove the bulb from the holder by press- 3. ing it in and twisting it counterclockwise. Insert a new bulb and reinstall the bulb holder in the headlight housing. 1. Turn the bulb holder counterclockwise, pull it out, and replace the bulb. 2. Reinstall the bulb holder. It can only be installed in one position. 1. Switch off all lights and turn the key to position 0. 2. Using a screwdriver or other suitable tool, pry out the fog light cover and pull it straight out as shown in the illustration. > (Release the clips (1) and then pull straight out (2).) 3. Unscrew the lamp housing's retaining screw and remove the housing. 4. Disconnect the connector from the bulb. 5. Turn the bulb counterclockwise and pull it out. * Option/accessory, for more information, see Introduction. 231 `` 09 Maintenance and servicing 09 Replacing bulbs 6. Press a new bulb into place and turn it clockwise. 7. Reinsert the bulb holder. The mark TOP should be upward. 8. Secure the fog light housing with the retaining screw and press the panel back into place. Removing the taillight bulb holder 2. Remove the covers (A or B) in the left/right panels to access the bulb holders. 3. Disconnect the wiring connector from the affected bulb holder. 4. Press the catches together and pull out the bulb holder. 5. Replace the defective bulb. 6. Press the wiring connector back into posi- tion. 7. Press the bulb holder into place and rein- stall the cover. Location of taillight bulbs Brake light Taillight/parking light/fog light Turn signal Back-up light Taillight/parking light Taillight/parking light NOTE If the message indicating a burned out bulb remains in the information display after the bulb has been replaced, consult a trained and qualified Volvo service technician. High-level brake light These bulbs should only be replaced by a trained and qualified Volvo service technician. All bulbs in the taillight cluster can be replaced from the cargo area. To access the bulb hold- ers: 1. Switch off all lights and turn the key to position 0. Location of taillight bulbs 232 License plate lighting Footwell lighting Cargo area lighting 09 Maintenance and servicing Replacing bulbs 09 1. Switch off all lights and turn the key to position 0. 2. Remove the screws with a screw driver. 3. Detach the lens (bulb housing) carefully. 4. Replace the defective bulb. 5. Reinstall the entire bulb housing and screw it into place. The footwell lighting is located under the dash- board on the driver's and passenger's sides. To replace a bulb: 1. Insert a screwdriver under the edge of the lens. Turn the screwdriver gently to detach the lens. 1. Insert a screwdriver and turn it gently to detach the bulb housing. 2. Remove the defective bulb. 3. 4. Press the bulb housing back into place. Install a new bulb. 2. Remove the defective bulb. 3. 4. Press the lens back into place. Install a new bulb. `` 233 09 Maintenance and servicing 09 Replacing bulbs Cabin lighting in the cargo area Vanity mirror lighting The rear cabin lighting consists of a light on the driver’s side of the cargo area 1. Insert a screwdriver and turn it carefully to release the lens. 2. Remove the connector from the bulb holder. 3. Replace the defective bulb. 4. Press the lens back into place. Removing the lens 1. Insert a flat screwdriver under the lens and carefully exert upward pressure to release the retaining clips. 2. Snap out the lens. 3. Use needle nose pliers to pull the bulb straight to the side. Replace the bulb. Do not exert too much pressure on the bulb with the pliers to help avoid damaging it. Reinserting the lens 1. Put the lens back into position. 2. Press it into place. 234 * Option/accessory, for more information, see Introduction. NOTE For information regarding any other bulbs not mentioned in this section, please con- tact your Volvo retailer or a trained and authorized Volvo service technician. Bulb specifications Lighting function Wattage Low beam headlights (halogen) High beam headlights (halogen) High beam headlights (models with Active Bending Lights*) Back-up lights Rear fog light 55 60 55 21 21 Bulb H11 LL HB3 H7 LL P21W LL P21/4W LL 09 Maintenance and servicing Replacing bulbs 09 Wattage Bulb W2.1x9.5d type T10 SV8.5 (length 38mm) Lighting function Footwell lighting Cargo compart- ment light NOTE Please consult a Volvo retailer’s Parts department for the most up-to-date speci- fications. Lighting function Taillights Rear turn signals Brake lights Front turn signals License plate light- ing Vanity mir- ror Front park- ing lights Front side marker lights Front fog lights* Glove com- partment light Wattage Bulb 21 21 24 35 P21/4W LL PY21W LL P21W LL PY24W SV C5W LL W2x4.6d type T5 W5W LL BV W5W LL H8 W2.1x9.5d type T10 * Option/accessory, for more information, see Introduction. 235 09 Maintenance and servicing 09 Fuses Replacing fuses There are relay/fuse boxes located in the engine compartment and the passenger com- partment. If an electrical component fails to function, this may be due to a blown fuse. The easiest way to see if a fuse is blown is to remove it. To do so: 1. Pull the fuse straight out. If a fuse is difficult to remove, special fuse removal tools are located on the inside of the fuse box cov- ers. 2. From the side, examine the curved metal 3. wire in the fuse to see if it is intact. If the wire is broken, insert a new fuse of the same color and amperage (written on the fuse). If fuses burn out repeatedly, have the electrical system inspected by a trained and qualified Volvo service technician. WARNING Never use metal objects or fuses with higher amperage than those stated on the follow- ing pages. Doing so could seriously damage or overload the vehicle's electrical system. 236 Fuse box in the engine compartment The fuse box in the engine compartment has positions for 36 fuses. • Fuses 1–18 are relays/circuit breakers and should only be removed or replaced by an authorized Volvo service technician. • Fuses 19–36 may be changed at any time when necessary. Several extra fuses and a fuse removal tool to assist in removing/replacing fuses can be found on the underside of the fuse box cover in the engine compartment. 09 Maintenance and servicing Fuses 09 `` 237 09 Maintenance and servicing 09 Fuses Fuses in the engine compartment 1. 2. 3. 4. 5. 6. 7. 8. Coolant fan (radiator) Power steering Feed to passenger com- partment fuse box Feed to passenger com- partment fuse box Element, climate unit Not in use ABS pump ABS valves 50A 80A 60A 60A 80A 30A 20A 9. 10. 11. 12. 13. 14. 15. 16. Engine functions Climate system blower Headlight washers 30A 40A 20A Feed to heated rear window 30A Starter motor relay Trailer connector (acces- sory) 30A 40A Not in use Feed to audio system 30A 17. Windshield wipers 18. 19. 20. 21. 22. 23. Feed to passenger com- partment fuse box Not in use Horn Not in use Not in use Engine control module (ECM)/transmission control module (TCM) 30A 40A 15A 10A 238 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. Not in use Not in use Ignition switch A/C compressor Not in use Front fog lights* Not in use Not in use Fuel injectors Heated oxygen sensor, vac- uum pump Ignition coils, climate unit pressure sensor Engine sensor valves, A/C relay, relay coil, PTC ele- ment oil trap, canister, mass air meter 36. Engine control module (ECM), throttle sensor 15A 10A 15A 10A 20A 10A 15A 10A 09 Maintenance and servicing Fuses 09 * Option/accessory, for more information, see Introduction. 239 `` 09 Maintenance and servicing 09 Fuses Fuse box in the passenger compartment 6. Pull the center pins fully out of the mount- ing clips, secure the upholstery with the mounting clips and press the pins into the mounting clips again. The mounting clips then expand, holding the upholstery in position. The fuse box in the passenger compartment is located under the glove compartment. To access the fuses: 1. Remove the upholstery covering the fuse box by first pressing in the center pins in the mounting clips approximately 0.5 in (1 cm) with a small screwdriver and then pulling the clips out. 2. Turn both retaining screws (2) counter- clockwise until they release. 3. Fold down the fuse box (3) half way. Pull it toward the seat until it stops. Fold it down completely. The fuse box can be unhooked completely. 4. Replace the blown fuse. 5. Close the fuse box in reverse order. 240 Fuses in the passenger compartment 09 Maintenance and servicing Fuses 09 43. 44. 45. 46. Fuse 37-42, not in use Audio system, Blue- tooth,Volvo Navigation sys- tem* Supplemental Restrain Sys- tem (SRS), engine control module 12-volt sockets Lighting – glove compart- ment, instrument panel, and footwells 15A 10A 15A 5A 47. 48. 49. 50. 51. 52. Interior lighting Rear liftgate wiper/washer Supplemental Restrain Sys- tem (SRS), Occupant Weight Sensor (OWS) Not in use Fuel filter relay Transmission control mod- ule (TCM), ABS 53. Power steering 5A 15A 10A 10A 5A 10A 54. 55. 56. Park assist*, Active Bending Lights* 10A Not in use Volvo Navigation System remote key module, alarm siren control module 57. On-board diagnostic socket, brake light switch 58. Right high beam, auxiliary lights relay 59. Left high beam 10A 15A 7.5A 7.5A * Option/accessory, for more information, see Introduction. 241 `` 09 Maintenance and servicing 09 Fuses 76. 77. 78. 79. 80. 81. 82. 83. 84. 85. 86. Not in use Not in use Not in use Back-up lights 5A Not in use Not in use Power window – front pas- senger's side door Power window and door lock – front driver's side door Power passenger's seat Power driver's seat Interior lighting relay, cargo area light, power seats 25A 25A 25A 25A 5A 60. 61. Heated driver's seat* Heated passenger's seat* 62. Moonroof* 63. 64. 65. 66. 67. 68. 69. 70. 71. 72. Not in use SiriusXM(cid:3397) satellite radio* Audio system Audio system control mod- ule (ICM), climate system Not in use Cruise control Climate system, rain sen- sor*, BLIS button* Not in use Not in use Not in use 73. Moonroof, front ceiling lighting, auto-dim mirror*, seat belt reminder 74. 75. Fuel pump relay Not in use 15A 15A 20A 5A 5A 10A 5A 5A 5A 15A 242 * Option/accessory, for more information, see Introduction. 09 Maintenance and servicing 09 243 Introduction .......................................................................................... 246 Audio functions..................................................................................... 247 Radio functions..................................................................................... 252 CD player.............................................................................................. 260 Audio menu........................................................................................... 263 Bluetooth® hands-free connection....................................................... 264 244 AUDIO 10 Audio Introduction Controls 10 POWER: press for on/off. If the audio sys- tem is on when the remote key is turned to position 0, it will continue to play until the key is removed from the ignition slot (or the driver's door is opened on vehicles with the optional keyless drive). The system will start automatically the next time the key is turned to position I. See page 149 for infor- mation about the ignition switch positions. Display Keypad MENU: opens the menu system Navigation control: Use the up/down arrows to navigate among menu alterna- tives. EXIT: press to exit the menu system ENTER: press to confirm a selection or activate/deactivate a function The audio system's functions can also be con- trolled from the steering wheel keypad. The menu alternatives are numbered and can be selected directly from the keypad. Press MENU and then the number(s) of the desired menu alternative. Audio levels The audio systems is available in three levels: • Performance1 • High Performance • Premium Sound* NOTE The audio system features and equipment described in this chapter may not be avail- able on all audio levels. 1 Certain Canadian models 246 * Option/accessory, for more information, see Introduction. matically according to the vehicle's speed, see page 251 for more information on this func- tion. Selecting a sound source – Press AM/FM (2) repeatedly to toggle between FM1, FM2, and AM. – Press MODE (3) repeatedly to toggle between the CD player and the external sound source AUX, USB, the optional Sir- iusXM(cid:3397) satellite radio or BT1. The currently selected sound source will be shown in the display. Daytime/twilight display In daylight the information in the center console screen is displayed against a light background. In darkness it is displayed against a dark back- ground. Audio system controls VOLUME dial AM/FM – select a radio band MODE – select a sound source TUNING dial SOUND button Navigation controls/menu selections Volume Use the volume dial (1) or the buttons in the steering wheel keypad to adjust the volume level. The volume level is also adjusted auto- 1 Bluetooth(cid:159) streaming audio 10 Audio Audio functions Steering wheel keypad 10 Steering wheel keypad The four buttons on the steering wheel keypad can also be used to control the audio system. These buttons can be used to adjust volume, shift between preset stations and change CD tracks. Press one of the two left-hand buttons briefly to change to the next/previous preset radio station, or to go to the next/previous track on a CD. Press and hold down these buttons to search within a track on a CD. `` 247 10 Audio Audio functions USB/AUX connector 10 Connectors in the center console AUX socket USB connector An auxiliary device, such as an iPod(cid:159)2, MP3 player or a USB flash drive can be connected to the audio system via the connectors in the center console storage compartment. A stand- ard cable from an iPod(cid:159) or MP3 player can be routed under the cover to the connector(s) in the storage compartment. 2 Registered trademark of Apple Computer Inc. 248 If the device is being charged through a 12-volt socket while it is connected to the AUX or port, sound quality may be impaired. A sound source must be chosen, depending on the device that has been connected: 1. Use MODE to select iPod or USB. The text Connect device will be displayed. 2. Connect the device to the connector in the center console storage compartment (see the illustration). The text LOADING will be displayed while the system loads the files (folder structure) on the device. This may take a short time. When information about the files (the folder structure) on the device has been loaded, the resulting list includes information on the artist, genre and song title. To navigate in the folder structure, press ENTER and scroll up and down the folders using the arrow buttons (on the audio system control panel or on the steering wheel keypad). Press the right arrow button to select a folder. Press the left arrow button to go up a level in the folder structure. Press ENTER to go down a level in the folder structure. Tracks can be selected in two ways: – Turn the Tuning knob (no. 4 in the illustra- tion on page 252) clockwise or counter- clockwise. – Use the right or left arrow keys on the nav- igation control (no. 5 in the illustration on page 252) to select the desired track. The arrow keys on the steering wheel keypad can also be used in the same way. NOTE • The system supports a number of iPod(cid:159) models produced in 2005 or later. • In order to help avoid damage to the USB socket, it will be switched off if there is a short circuit or if the con- nected device uses too much current (which can happen if the device does not comply with the USB standard). The USB socket will reactivate the next time the ignition is switched on if the problem no longer exists. If the problem persists, contact a trained and authorized Volvo service technician. USB flash drive To simplify the use of a USB flash drive, it is advisable to only store music files on the drive. It will take considerably longer for the system to index the files on the drive if it contains any- thing other than compatible music files. NOTE • The system supports removable media that uses the USB 2.0 standard and the FAT32 file system. It can index up to 1,000 folders and a maximum of 254 sub-folders/files for each folder. How- ever, the highest folder level can sup- port up to 1,000 sub-folders/files. • When using a longer type of USB device, connecting it with a USB adapter cable will help reduce mechan- ical wear on the USB socket and on the device. MP3 player Many MP3 players have a file indexing system that is not supported by the vehicle's audio system. In order to use an MP3 player, the sys- tem must be set to USB Removable device/ Mass Storage Device. iPod(cid:159) An iPod(cid:159) receives current and its battery is charged through the connecting cord. How- ever, if the iPod's battery is completely drained, it should be recharged before the iPod(cid:159) is connected to the audio system. NOTE When an iPod(cid:159) is used as a sound source, the vehicle's audio system has a menu structure similar to the one in the iPod(cid:159). See the iPod's manual for detailed information. For further information, refer to the accessory manual USB/iPod(cid:159) Music Interface. Adjusting volume for an external device The volume of an external device may be dif- ferent from the volume of the internal sound sources such as the CD player or the radio. It the external device's volume is too high, the quality of the sound may be impaired. To help prevent this, adjust the external device's input volume as follows: 1. While playing the radio or a CD, lower the audio volume to about one-quarter. 2. Switch to AUX mode on the audio system by pressing the MODE button. 3. Connect the headphone output from your music player to the AUX input using a cable with a stereo 3.5 mm miniplug at both ends. 4. Set your music player's headphone vol- ume to three-quarters using the player's volume controls. 10 Audio Audio functions 5. Press MENU on the audio system, and navigate to AUX input volume. 6. Turn the volume knob to raise or lower the AUX input volume until you hear music at a comfortable level. If there is distortion, lower your music play- er's headphone volume until the distortion goes away. 7. 8. Finally, exit the menu and adjust the audio volume to a comfortable level. Bluetooth(cid:159) streaming audio (BT) The vehicle's audio system is equipped with Bluetooth(cid:159), which makes it possible to play streaming audio files from a Bluetooth(cid:159)con- nected cell phone. Navigation and control of the phone can be done through the vehicle's center console control panel or the steering wheel keypad. On certain cell phones, it is also possible to change tracks from the phone itself. In order to listen streaming audio, BT must be selected as a sound source (see page 247) and a Bluetooth(cid:159) cell phone must be connected (paired) with the audio system. See page 264 for more information. 10 249 10 Audio Audio functions NOTE 10 Any Bluetooth cell phones used must sup- port Audio/Video Remote Control Profile (AVRCP) and Advanced Audio Distribution Profile (A2DP). The phone must use AVRCP version 1.3 and A2DP 1.2. If older versions of these standards are used, certain fea- tures (e.g., scan or random) may not func- tion. Not all cell phones are fully compatible with the vehicle's Bluetooth system. A list of compatible phones is available at you Volvo retailer or at www.volvocars.us. Listening to streaming audio Press MODE several times to select BT as a sound source. Audio files on the connected device can be selected in three ways: • Turn the TUNING dial (4) in either direction. • Use the navigation buttons (6) to select an audio file. • Use the buttons on the steering wheel keypads. 250 Sound settings Optimal sound reproduction The audio system is calibrated for optimal sound reproduction through the use of digital signal processing. This calibration takes into account the speakers, amplifier, cabin acous- tics, the seating position of the listener, etc., for each combination of vehicle and audio system. There is also dynamic calibration that takes into account the setting of the volume control, radio reception, and the vehicle's speed. The sound settings described in this manual, such as BASS, TREBLE, and Equalizer front…/ Equalizer rear… are only intended to enable the user to adapt sound reproduction to his/her personal preferences. 1. Press SOUND (5). Press this button repeatedly until you come to the setting that you wish to change. 2. Turn the TUNING dial (4) to make the desired setting. The following settings can be made: BASS–set the bass level TREBLE–set the treble level BALANCE–set the left/right sound balance FADER–set the front/rear sound balance CENTER–make settings for the center speaker SURROUND–make settings for surround sound Surround sound Surround sound settings are used to balance sound levels throughout the vehicle. Surround settings for the var- ious sound sources are made sepa- rately. NOTE • Dolby Surround Pro Logic II is only available on the Premium Sound sys- tem. • When listening to FM radio stations, Dolby Surround Pro Logic II functions best in areas with strong reception. If reception is weak, selecting 2 or 3- channel stereo may provide better sound quality. The Dolby symbol will appear in the display when Dolby Pro Logic II is activated. There are three alternative settings: • Pro Logic II • 3-channel • Off (normal 2-channel stereo) Dolby Surround Pro Logic II(cid:159) distributes the stereo sound's two channels to the left, center, right and rear speakers, making sound repro- duction more authentic than ordinary two- channel stereo. Dolby Surround Pro Logic II(cid:159) and the Dolby symbol are trademarks of Dolby Laboratories Licensing Corporation. The Dolby Surround Pro Logic II System(cid:159) is manufactured under licence from Dolby Laboratories Licensing Corporation. Activating/deactivating Surround sound 1. Press MENU followed by ENTER. 2. Select SUBWOOFER in the menu and press ENTER. 3. Select Surround SURROUND AM/ SURROUND FM/SURROUND CD/ SURROUND AUX and press ENTER.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2013 Volvo C30 Owners Manual