2009 Volvo C30 Owners Manual

when replacing the high/low beam, parking

5. Disconnect the wiring connector by press- ing down the clip with your thumb while at the same time pulling the connector with your other hand.

(cid:96)(cid:96)

213

09 Maintenance and servicing

09

Replacing bulbs

6. Lift out the headlight housing and place it on a soft surface to avoid scratching the lens.

Low beam bulb

CAUTION

When disconnecting the connector, pull on the connector itself and not on the wiring.

After the defective bulb has been replaced, reinsert the housing in the reverse order. Check that the retaining pin is correctly inserted.

WARNING

Bi-Xenon headlights (option) – due to the high voltage used by these headlights, these bulbs should only be replaced by a trained and qualified Volvo service techni- cian.

214

Low beam bulb

Cover with retaining clamps 1. Open the hood and remove the headlight

housing (see page 213 for instructions).

2. Release the retaining clamps on the cover. 3. Release the bulb's retaining spring holding the bulb in place by pressing it first to the left and then moving it outward and down- ward.

4. Pull out the bulb.

Installing a new bulb 1.

Insert the new bulb. It can only be installed in one position.

2. Press the retaining spring inward and upward and slightly to the right until it snaps into place.

3. Press the wiring connector onto the bulb. 4. Put the plastic cover in place. 5. Press the retaining clamps back into place. 6. Reinstall the headlight housing (see

page 213).

High beam bulb

WARNING

Parking light bulb

09 Maintenance and servicing

Replacing bulbs

09

Bi-Xenon(cid:159) headlights (option) – due to the high voltage used by these headlights, the Bi-Xenon(cid:159) bulbs should only be replaced by a trained and qualified Volvo service tech- nician.

3. Driver's side headlight: Turn the bulb

holder counterclockwise. Passenger's side headlight: Turn the bulb holder clockwise.

4. Pull out the bulb holder and replace the

bulb.

5. Reinstall the bulb holder. It can only be

installed in one position.

6. Reinstall the headlight housing (see

page 213).

Halogen high beam bulb 1. Open the hood. 2. Remove the headlight housing (see

page 213).

NOTE

The halogen high beam bulb has a different socket on vehicles equipped with Bi- Xenon(cid:159) headlights. On these models, pull the bulb straight out.

1. Pull out the bulb holder with a pair of pliers.

The bulb holder should not be pulled out by the wire.

2. Replace the bulb. 3. Press the bulb holder back into place. It

can only be installed in one position.

(cid:96)(cid:96)

215

09 Maintenance and servicing

09

Replacing bulbs

Turn signal

Side marker light

Front fog light (option)

1. Turn the bulb holder counterclockwise and

remove it.

2. Remove the bulb from the holder by press-

ing it in and twisting it counterclockwise. Insert a new bulb and reinstall the bulb holder in the headlight housing.

3.

216

1. Turn the bulb holder counterclockwise,

pull it out, and replace the bulb.

2. Reinstall the bulb holder. It can only be

installed in one position.

1. Switch off all lights and turn the key to

position 0.

2. Remove the panel around the fog light

housing.

3. Unscrew both torx screws in the fog light

housing and remove it.

4. Disconnect the connector from the bulb. 5. Turn the bulb counterclockwise and pull it

6.

out. Install the new bulb in its seat and turn it clockwise.

7. Reconnect the connector to the bulb.

09 Maintenance and servicing

Replacing bulbs

09

8. Secure the fog light housing with the screws and press the panel back into place.

Removing the taillight bulb holder

3. Disconnect the wiring connector from the

affected bulb holder.

4. Press the catches together and pull out the

bulb holder.

5. Replace the defective bulb. 6. Press the wiring connector back into posi-

tion.

7. Press the bulb holder into place and rein-

stall the cover.

Location of taillight bulbs

All bulbs in the taillight cluster can be replaced from the cargo area. To access the bulb hold- ers: 1. Switch off all lights and turn the key to

position 0.

2. Remove the covers (A or B) in the left/right

panels to access the bulb holders.

Location of taillight bulbs

1 The wiring to the LED brake lights is permanently connected to the bulb holder. It should not be removed.

Brake light (LED)1

Taillight/parking light/fog light (driver’s side only) Taillight/parking light

Turn signal

Back-up light

Taillight/parking light

NOTE

If the message indicating a burned out bulb remains in the information display after the bulb has been replaced, consult a trained and qualified Volvo service technician.

High-level brake light These bulbs should only be replaced by a trained and qualified Volvo service technician.

(cid:96)(cid:96)

217

09 Maintenance and servicing

09

Replacing bulbs

License plate lighting

Rear grids

Footwell lighting

1. Switch off all lights and turn the key to

position 0.

2. Remove the screws with a screw driver. 3. Detach the lens (bulb housing) carefully. 4. Replace the defective bulb. 5. Reinstall the entire bulb housing and screw

it into place.

The grids are held in place by clips and can be pressed into position. They can only be instal- led one way.

The footwell lighting is located under the dash- board on the driver's and passenger's sides. To replace a bulb: 1.

Insert a screwdriver under the edge of the lens. Turn the screwdriver gently to detach the lens.

2. Remove the defective bulb. 3. 4. Press the lens back into place.

Install a new bulb.

218

Cargo area lighting

Cabin lighting in the cargo area

Vanity mirror lighting

09 Maintenance and servicing

Replacing bulbs

09

1.

Insert a screwdriver and turn it gently to detach the bulb housing.

2. Remove the defective bulb. 3. 4. Press the bulb housing back into place.

Install a new bulb.

The rear cabin lighting consists of a light on the driver’s side of the cargo area 1.

Insert a screwdriver and turn it carefully to release the lens.

2. Remove the connector from the bulb

holder.

3. Replace the defective bulb. 4. Press the lens back into place.

1.

Insert a screwdriver under the center of the lower edge of the mirror, turn it, and care- fully pry up the lugs at the edge.

2. Move the screwdriver under the edge on

the left and right-hand sides (near the black rubber sections) and pry carefully to release the lower edge of the mirror.

3. Pry carefully and lift out the entire mirror

and the cover.

4. Remove the defective bulb and replace it

with a new one.

5. To reinstall the mirror, begin by pressing

the three lugs at the upper edge of the mir- ror back into place.

(cid:96)(cid:96)

219

09 Maintenance and servicing

09

Replacing bulbs

6. Press the three lower lugs back into place.

220

09 Maintenance and servicing

Fuses

09

Replacing fuses There are relay/fuse boxes located in the engine compartment and the passenger com- partment. If an electrical component fails to function, this may be due to a blown fuse. The easiest way to see if a fuse is blown is to remove it. To do so: 1. Pull the fuse straight out. If a fuse is difficult to remove, special fuse removal tools are located on the inside of the fuse box cov- ers.

2. From the side, examine the curved metal

3.

wire in the fuse to see if it is intact. If the wire is broken, insert a new fuse of the same color and amperage (written on the fuse).

If fuses burn out repeatedly, have the electrical system inspected by a trained and qualified Volvo service technician.

WARNING

Never use metal objects or fuses with higher amperage than those stated on the follow- ing pages. Doing so could seriously damage or overload the vehicle's electrical system.

(cid:96)(cid:96)

221

09 Maintenance and servicing

09

Fuses

Fuse box in the engine compartment

The fuse box in the engine compartment has positions for 36 fuses. • Fuses 1–18 are relays/circuit breakers and should only be removed or replaced by an authorized Volvo service technician.

• Fuses 19–36 may be changed at any time

when necessary.

Several extra fuses and a fuse removal tool to assist in removing/replacing fuses can be found on the underside of the fuse box cover in the engine compartment.

222

Fuses in the engine compartment

09 Maintenance and servicing

Fuses

09

1.

2.

3.

4.

5.

6.

7.

8.

Coolant fan (radiator)

Power steering

Feed to passenger com- partment fuse box

Feed to passenger com- partment fuse box

Element, climate unit

Not in use

ABS pump

ABS valves

50A

80A

60A

60A

80A

30A

20A

9.

10.

11.

12.

13.

14.

15.

16.

Engine functions

Climate system blower

Headlight washers

30A

40A

20A

Feed to heated rear window 30A

Starter motor relay

Trailer connector (acces- sory)

30A

40A

Not in use

Feed to audio system

30A

17. Windshield wipers

18.

19.

20.

21.

22.

23.

Feed to passenger com- partment fuse box

Not in use

Horn

Not in use

Not in use

Engine control module (ECM)/transmission control module (TCM)

30A

40A

15A

10A

(cid:96)(cid:96)

223

09 Maintenance and servicing

09

Fuses

24.

25.

26.

27.

28.

29.

30.

31.

32.

33.

34.

35.

Not in use

Not in use

Ignition switch

A/C compressor

Not in use

15A

10A

Front fog lights (option)

15A

Not in use

Not in use

Fuel injectors

Heated oxygen sensor, vac- uum pump

Ignition coils, climate unit pressure sensor

Engine sensor valves, A/C relay, relay coil, PTC ele- ment oil trap, canister, mass air meter

10A

20A

10A

15A

10A

36.

Engine control module (ECM), throttle sensor

224

09 Maintenance and servicing

Fuses

09

Fuse box in the passenger compartment

The fuse box in the passenger compartment is located under the glove compartment. To access the fuses: 1. Remove the upholstery covering the fuse box by first pressing in the center pins in the mounting clips approximately 0.5 in (1 cm) with a small screwdriver and then pulling the pins out.

2. Turn both retaining screws (2) counter-

clockwise until they release.

3. Fold down the fuse box (3) half way. Pull it toward the seat until it stops. Fold it down completely. The fuse box can be unhooked completely.

4. Replace the blown fuse. 5. Close the fuse box in reverse order.

6. Pull the center pins fully out of the mount-

ing clips, secure the upholstery with the mounting clips and press the pins into the mounting clips again. The mounting clips then expand, holding the upholstery in position.

(cid:96)(cid:96)

225

09 Maintenance and servicing

09

Fuses

Fuses in the passenger compartment

44.

45.

46.

47.

48.

Supplemental Restrain Sys- tem (SRS), engine control module

12-volt socket in rear seat

Lighting – glove compart- ment, instrument panel, and footwells

Interior lighting

Rear liftgate wiper/washer

10A

15A

5A

5A

15A

49.

50.

51.

52.

53.

54.

Supplemental Restrain Sys- tem (SRS), Occupant Weight Sensor (OWS)

10A

Not in use

Fuel filter relay

Transmission control mod- ule (TCM), ABS

Power steering

Park assist (option) Bi- Xenon(cid:159) headlights (option)

10A

5A

10A

10A

55.

Not in use

Not in use

Not in use

Not in use

Not in use

Not in use

Not in use

Audio system, Volvo Navi- gation system (option)

15A

37.

38.

39.

40.

41.

42.

43.

226

09 Maintenance and servicing

Fuses

09

84.

85.

86.

Power passenger's seat

Power driver's seat

Interior lighting relay, cargo area light, power seats

25A

25A

5A

56.

Volvo Navigation System remote control module (option), alarm siren control module

57. On-board diagnostic

socket, brake light switch

58.

59.

60.

61.

Right high beam, auxiliary lights relay

Left high beam

Heated driver's seat (option)

Heated passenger's seat (option)

62. Moonroof (option)

63.

64.

65.

66.

67.

68.

Not in use

Audio system, Volvo Navi- gation system (option)

Audio system

Audio system control mod- ule (ICM), climate system

Not in use

Cruise control

10A

15A

7.5A

7.5A

15A

15A

20A

5A

5A

10A

5A

69.

70.

71.

72.

Climate system, rain sensor (option), BLIS button (option)

5A

Not in use

Not in use

Not in use

73. Moonroof, front ceiling

lighting, auto-dim mirror, (option) seat belt reminder

74.

75.

76.

77.

78.

79.

80.

81.

82.

83.

Fuel pump relay

Not in use

Not in use

Not in use

Not in use

Back-up lights

Not in use

Not in use

Power window – front pas- senger's side door

Power window and door lock – front driver's side door

5A

15A

5A

20A

25A

25A

227

Audio functions..................................................................................... 230
Radio functions..................................................................................... 234
CD player/CD changer.......................................................................... 239
Audio menu........................................................................................... 243
Bluetooth(cid:159) hands-free connection....................................................... 244

228

AUDIO

10

10 Audio

Audio functions

Audio system controls

10

VOLUME dial

AM/FM – select a radio band

MODE – select a sound source

TUNING dial

SOUND button

Auxiliary connector

Selecting a sound source • Press AM/FM (2) repeatedly to toggle

between FM1, FM2, and AM.

• Press MODE (3) repeatedly to toggle

between the CD player and the optional external sound source AUX or the optional Sirius satellite radio.

The currently selected sound source will be shown in the display.

AUX The AUX (auxiliary) port, located under the cen- ter armrest, can be used to connect for exam- ple, an mp3 player.

230

If the player is being charged through a 12-volt socket while it is connect to the AUX port, sound quality may be impaired. The volume of the external sound source AUX may be different from the volume of the internal sound sources such as the CD player or the radio. If the external sound source's volume is too high, the quality of the sound may be impaired. This can be prevented by adjusting the external sound source's input volume. 1. While playing the radio or a CD, lower the

audio volume to about one-quarter.

2. Switch to AUX mode on the audio system

by pressing the MODE button.

3. Connect the headphone output from your music player to the AUX input using a cable with a stereo 3.5 mm miniplug at both ends.

4. Set your music player's headphone vol- ume to three-quarters using the player's volume controls.

5. Press MENU on the audio system, and navigate to AUX Volume or AUX Input Volume.

6. Turn the volume knob to raise or lower the AUX Input Volume until you hear music at a comfortable level.

7.

If there is distortion, lower your music play- er's headphone volume until the distortion goes away.

8. Finally, exit the menu and adjust the audio

volume to a comfortable level.

Volume Use the volume dial (1) or the buttons in the steering wheel keypad to adjust the volume level. The volume level is also adjusted auto- matically according to the vehicle's speed, see page 233 for more information on this func- tion.

Steering wheel keypad

The four buttons on the steering wheel keypad can be used to control the audio system. The steering wheel keypad can be used to adjust volume, shift between preset stations and change CD tracks. Press one of the two left- hand buttons briefly to change to the next/ previous preset radio station, or to go to the next/previous track on a CD. Press and hold down these buttons to search within a track on a CD.

Daytime/twilight display In daylight the information is displayed against a light background. In darkness it is displayed against a dark background.

USB/iPod connector (option)

Steering wheel keypad

10 Audio

Audio functions

An auxiliary device, such as an iPod, MP3
player or a USB flash drive can be connected to the audio system via the connector in the center console storage compartment. A stand- ard cable from an iPod or MP3 player can be routed under the cover to the AUX connector in the storage compartment. A sound source must be chosen, depending on the device that has been connected: 1. Use MODE to select iPod or USB. The text

CONNECT DEVICE will be displayed.

2. Connect the device to the connector in the center console storage compartment (see the illustration).

The text LOADING will be displayed while the system loads the files (folder structure) on the device. This may take a short time. When information about the files (the folder structure) on the device has been loaded, the resulting list includes information on the artist, genre and song title. To navigate in the folder structure, press ENTER and scroll up and down the folders using the arrow buttons (on the audio system control panel or on the steering wheel keypad). Press the right arrow button to select a folder. Press the left arrow button to go up a level in the folder structure. Press ENTER to go down a level in the folder structure.

10

(cid:96)(cid:96)

231

10 Audio

Audio functions

Tracks can be selected in two ways: • Turn the Tuning knob (no. 4 in the illustra-

tion on page 234) clockwise or counter- clockwise

• Use the right or left arrow keys on the nav- igation control (no. 5 in the illustration on page 234) to select the desired track. The arrow keys on the steering wheel keypad can also be used in the same way.

NOTE

The system supports playback of files in the most common versions of formats such as mp3, wma, and wav. However, there may be versions of these formats that the system does not support.

USB flash drive To simplify the use of a USB flash drive, it is advisable to only store music files on the drive. It will take considerably longer for the system to index the files on the drive if it contains any- thing other than compatible music files.

MP3 player Many mp3 players have a file indexing system that is not supported by the vehicle's audio system. In order to use an mp3 player, the sys- tem must be set to USB Removable device/ Mass Storage Device.

iPod An iPod receives current and its battery is charged through the connecting cord. How- ever, if the iPod's battery is completely drained, it should be recharged before the iPod is connected to the audio system.

NOTE

When an iPOD is used as a sound source, the vehicle's audio system has a menu structure similar to the one in the iPOD. See the iPOD's manual for detailed information.

For further information, refer to the accessory manual USB/iPod Music Interface.

Sound settings

Optimal sound reproduction The audio system is calibrated for optimal sound reproduction through the use of digital signal processing. This calibration takes into account the speakers, amplifier, cabin acous- tics, the seating position of the listener, etc., for each combination of vehicle and audio system. There is also dynamic calibration that takes into account the setting of the volume control, radio reception, and the vehicle's speed. The sound settings described in this manual, such as BASS, TREBLE, and EQUALIZER are only

10

232

intended to enable the user to adapt sound reproduction to his/her personal preferences. 1. Press SOUND (5). Press this button

repeatedly until you come to the setting that you wish to change.

2. Turn the TUNING dial (4) to make the

desired setting.

The following settings can be made: BASS–set the bass level TREBLE–set the treble level BALANCE–set the left/right sound balance FADER–set the front/rear sound balance CENTER–make settings for the center speaker SURROUND–make settings for surround sound

Surround sound

Surround sound settings are used to balance sound levels throughout the vehicle. Surround settings for the var- ious sound sources are made sepa-

rately.

NOTE

• Dolby Surround Pro Logic II is only

available on the Premium Sound sys- tem.

• When listening to FM radio stations, Dolby Surround Pro Logic II functions best in areas with strong reception. If reception is weak, selecting 2 or 3- channel stereo may provide better sound quality.

The Dolby symbol will be appear in the display when Dolby Pro Logic II is activated. There are three alternative settings: • Pro Logic II • 3-channel • Off (normal 2-channel stereo) Activating/deactivating Surround sound 1. Press MENU followed by ENTER. 2. Select AUDIO SETTINGS in the menu and

press ENTER.

3. Select Surround FM/AM/CD/AUX and

press ENTER.

4. Select Pro logic II, 3-channel stereo or

Off and press ENTER.

1 Default setting.

Equalizer Front/Rear This function is used to fine-tune the sound level for different frequencies separately.

NOTE

This function is only available on certain sound systems.

To adjust the equalizer settings: 1. Press MENU followed by ENTER. 2. Select AUDIO SETTINGS in the menu and

press ENTER.

3. Select Equalizer Front/Rear and press

ENTER.

The column in the display indicates the sound level for the current frequency. • Adjust the level with the TUNING dial (4), or use the Up/Down arrows. Additional fre- quencies can be selected with the Right/ Left arrows.

• Save the settings by pressing ENTER or

exit without saving by pressing EXIT.

Automatic sound control The audio system's volume is adjusted auto- matically according to the speed of the vehicle.

10 Audio

Audio functions

10

There are three settings available, which deter- mine the level of volume compensation: • Low • Medium1
• High To set the automatic sound level: 1. Press MENU followed by ENTER. 2. Select AUDIO SETTINGS in the menu and

press ENTER.

3. Select AUTO. VOLUME CONTROL in the

menu and press ENTER.

4. Select Low, Medium, or High and press

ENTER.

233

10 Audio

Radio functions

Radio function controls

10

Searching for stations There are two ways to manually tune a radio station: 1. Turn the TUNING dial (3) to the desired fre-

quency.

2. Press the left or right arrow key on the MENU NAVIGATION CONTROL and hold it down. The radio scans slowly in the selected direction and will increase the scanning speed after a few seconds. Release the button when the desired fre- quency appears in the display.

The frequency can be fine-tuned by short presses on the left/right arrow keys.

1. AM/FM1/FM2 selection 2. Station preset buttons 3. TUNING dial for selecting radio stations 4. SCAN 5. MENU NAVIGATION CONTROL–press the up or down arrow keys to scroll in a menu, or the keys on the left/right sides of the control to search for or change radio stations/CD tracks

6. EXIT–press to cancel a menu selection or

a selected function

7. AUTO–search for and store the strongest radio stations in the area in which you are driving

Storing preset stations

Manually storing a station 1. Tune to the desired station. 2. Press and hold the preset button under

which the station is to be stored. The audio system sound will be interrupted for a few seconds and STATION STORED will appear in the display.

NOTE

A total of 30 stations can be stored; 10 sta- tions each in AM, FM1 and FM2.

234

Automatically storing a station Pressing AUTO (7) automatically searches for and stores up to ten strong AM or FM stations in a separate memory. If more than ten stations are found, the ten strongest ones are stored. This function is especially useful in areas in which you are not familiar with radio stations or their frequencies. To use the AUTO function: 1. Select a waveband using the AM/FM but-

ton (1).

2. Start the search by pressing AUTO until AUTO STORING appears in the display.

When the search is completed, AUTO STORING will no longer be displayed. If there are no stations with sufficient signal strength, NO AST FOUND is displayed. The auto-stored stations can be selected using the preset buttons (2). Press EXIT (6) to terminate the automatic stor- ing function. When the radio is in auto-store mode, AUTO is shown in the display. AUTO disappears when you return to normal radio mode, which can be done by briefly pressing AM/FM (1), EXIT (6), or AUTO (7).

To return to the Auto-store mode, press the AUTO button briefly and select a stored station by pressing one of the preset buttons (2).

Saving auto-stored stations in the preset memory An auto-stored station can be saved in the memory for manually preset stations. 1. Press AUTO (7) briefly.

> Auto is displayed.

2. Press one of the preset buttons (2) under

which the station is to be stored. Hold down the button until STATION STORED is displayed.

The radio will then exit auto-store mode and the stored station can be selected by pressing the preset button.

Scanning SCAN (4) automatically searches through the selected waveband for strong AM or FM sta- tions. When the radio finds a station, that sta- tion will be played for approximately 8 sec- onds, after which scanning resumes.

Activating/deactivating SCAN 1. Select radio mode using the AM/FM but-

ton (2).

2. Press SCAN to activate the function.

SCAN is shown in the display.

3. Press the SCAN or EXIT button to deacti-

vate the scan function and listen to the selected station.

Storing a station found with SCAN A station can be stored as a preset while the SCAN function is activated. • Press one of the preset buttons (2) under

which the station is to be stored. Hold down the button until STATION STORED is displayed.

The SCAN function will be deactivated and the station can be selected by pressing the preset button.

Radio text Certain stations broadcast program informa- tion, which can be shown in the display. To start this function: 1. Select FM1 or FM2 and press the MENU

button.

2. Press ENTER. 3. Select RADIOTEXT in the menu and press

ENTER.

To deactivate this function, select RADIOTEXT again and press ENTER.

10 Audio

Radio functions

Listening to satellite radio The Sirius satellite system consists of a number of high elevation satellites in geosynchronous orbit.

10

NOTE

• The digital signals from the Sirius satel- lites are line-of-sight, which means that physical obstructions such as bridges, tunnels, etc, may temporarily interfere with signal reception.

• Avoid any obstructions, such as metal- lic objects transported on roof racks or in a ski box, or other antennas that may impede signals from the SIRIUS satel- lites.

Selecting Sirius radio mode 1. Press Power to switch on the audio system (see page 234 for information on the stand- ard radio functions).

2. Press the MODE button repeatedly until

Sirius 1 or 2 is displayed.

Activating Sirius radio 1. Tune to a satellite channel that has no audio, which means that the channel is unsubscribed and the text "Call 888-539- SIRIUS TO SUBSCRIBE" is displayed

(cid:96)(cid:96)

235

10 Audio

Radio functions

(see also "Selecting a channel" in the right column).

5. Use the left or right arrow keys to select a channel in the currently chosen category.

1. Press MENU and scroll to "Direct channel

entry."

2. Call Sirius at 1-888-539-SIRIUS (7474). 3. When asked for the Sirius ID number press

4.

AUTO to display this number. It is also possible to retrieve the Sirius ID from the MENU. "UPDATING SUBSCRIPTION" will be displayed while the subscription is being updated, after which the display will return to the normal view.

SIRUS ID The SIRIUS ID is required when contacting the Sirius Call Center. It is used to activate your account and when making any account trans- actions. The SIRIUS ID is sometimes referred to as the Electronic Serial Number (ESN).

Selecting a channel category 1. Select Sirius radio mode as described

above.

2. Press ENTER. 3. Use the up/down arrow keys to scroll

through the list of categories.

4. Press ENTER or the right arrow key to

select a category.

6. Press ENTER to listen to a channel.

NOTE

• The category "All" is default, which ena- bles you to scroll through the entire list of available satellite channels.

• The channel categories are automati-

cally updated several times a year. This takes approximately two minutes and will interrupt normal broadcasting. A message will be displayed while updat- ing is in progress. Information on chan- nel or feature updates is available at www.sirius.com.

Selecting a channel There are three ways of tuning in a channel: • Using the left and right arrow keys • By turning the tuning control • Through direct channel entry Direct channel entry The Sirius satellite channels are numbered consecutively throughout all of the categories. To access a channel directly:

2. Use the numerical keypad to enter the

channel's number.

3. Press ENTER. The radio will tune to this channel, even if it belongs to a category other than the currently selected one.

NOTE

• The numbers of skipped or locked

channels will not be displayed.

• If a channel is locked, the access code must be entered before the channel can be selected. See "Unlocking a channel" on page 237.

Scanning

NOTE

SCAN automatically searches through the list of satellite channels. see page 235 for more detailed information.

Storing a channel • A long press on one of the number keys stores the currently tuned channel on that key.

• A short press on a number key while the radio is in Sirius 1or 2 mode will tune to the

10

236

preset satellite channel stored on that but- ton, regardless of the currently selected channel category.

Song Seek and Song Memory The Song Seek and Song Memory functions provide both audio and visual notification when Sirius is broadcasting your favorite songs. Song Seek enables you to store the name of the song for future advance notification when that song is being played. The Song Memory feature makes it possible to view all of the cur- rent songs that are stored in memory.

Song memory Up to ten songs can be saved in the system's memory. 1. Press MENU. 2. Scroll to "Add song to song mem." and

follow the instructions shown in the dis- play.

If a new song is selected when the memory is full, you will be prompted to press ENTER to delete the last song on the list.

NOTE

The remaining songs in the list will move down one position, and the newly added song will be placed at the top of the list.

Song seek When a satellite radio channel plays one of the songs stored in the song memory, the listener will be alerted by a text message and an audi- ble signal. • Press ENTER to listen to the song or

EXIT to cancel.

To activate/deactivate the song seek function: 1. Press MENU 2. Scroll to "Song seek" 3. Press ENTER to activate or deactivate the

function.

NOTE

When the song has ended, the radio will remain tuned to the channel on which the song was played.

Radio text The text that is displayed about the song that is currently playing can be changed. Use the AUTO button or the menu to display the Artist, Title, Composer, or switch radio text off.

10 Audio

Radio functions

Advanced settings This menu function enables you to make set- tings on certain Sirius satellite radio functions. To access this menu: 1. Press MENU. 2. Scroll to Sirius menu. 3. Select Advanced Sirius settings.

WARNING

Settings should be made when the vehicle is at a standstill.

The following settings can be made in the Sir- ius menu. • Songs can be added to the song list • Channel skip settings can be made • Channel lock settings can be made • The channel access code can be displayed

or changed

• Your Sirius ID can be displayed Skip options This function is used to remove a channel from the list of available channels. Skip current 1. Select CHANNEL SKIP LIST and press

ENTER.

10

(cid:96)(cid:96)

237

10 Audio

Radio functions

2. Select a category in the list and press

ENTER.

3. Skip channels in the list presented by

pressing ENTER or right arrow key.

Unskip all channels This permanently removes all channels from the skip list and makes them available for selection. Temp. unskip all ch. This function will temporarily unskip all chan- nels and make them available for selection. The channels remain on the skip list and will again be skipped the next time the ignition is switched on. Channel lock Access to specific channels can be restricted (locked). A locked channel will not provide audio, song titles, or artist information.

NOTE

All channels are initially unlocked.

Locking a channel 1. Select "Sirius ID" in the menu and select

LOCK OPTIONS and press ENTER.

2. Select CHANNEL LOCK LIST and press

ENTER

3. Enter the channel access code and press

ENTER.

4. Select a category in the list and press

ENTER.

5. Lock channels in the list presented by

pressing ENTER or right arrow.

The channel is now locked and a checked box will be displayed to indicate this. It will be nec- essary to enter the channel access code1 in order to listen to a locked channel. Unlocking a channel: A channel's access code1 is required to unlock a channel. Unlock all channels This permanently removes all channels from the locked list and makes them available for selection. Temp. unlock all ch. This function will temporarily unlock all chan- nels and make them available for selection. The channels remain on the locked list and will again be locked the next time the ignition is switched on.

CHANGE CODE This function makes it possible to change the channel access code. The default code is 0000. To change the code: 1. Select CHANGE CODE and press

ENTER.

2. Enter the current code and press ENTER. 3. Enter the code and press ENTER. 4. Confirm the new code and press ENTER. If an incorrect code is entered, the text WRONG CODE! is displayed. If you have forgotten the access code: 1. Select "SIRIUS ID" in the Sirius settings

menu and press ENTER.

2. Press and hold the ENTER button for

2 seconds.

3. The current code will be displayed. Your Volvo retailer can also provide you with assistance.

SIRUS ID This function displays the 12-digit Sirius acti- vation ID.

10

238

CD function controls

Playing a CD

Single CD player Start the CD player by pressing the MODE but- ton (5) and inserting a disc in the slot (4). If there is already a disc inserted, it will begin to play.

NOTE

If a CD is in the slot when the audio system is in CD mode, the CD will be played auto- matically.

CD changer (option) The CD changer can hold up to six discs. 1. Start the CD changer by pressing the

MODE button (5).

2. Select an empty position using the 1 – 6

buttons or the up/down keys on the MENU NAVIGATION CONTROL. The display shows which positions are empty. Insert a disc into the slot (4).

3.

MENU NAVIGATION CONTROL–press the up or down arrow keys to scroll in a menu, or the keys on the left/right sides of the control to change CD tracks/fast for- ward/back Buttons for selecting a disc in the optional CD changer CD eject button

CD slot

MODE button

TUNING dial for selecting tracks

10 Audio

CD player/CD changer

NOTE

• Ensure that INSERT DISC is displayed

before inserting a disc.

• If a CD position in the changer contain-

ing a disc is selected, and the audio system is in CD mode when it is switched on, the CD will play automati- cally.

10

CD eject Eject from Single CD player Press the eject button (3) to eject the disc. Eject from CD changer This function makes it possible to eject a single disc, or to eject all of the discs in the changer. • Press the eject button (3) briefly to eject the

disc that is currently playing.

• A longer press (more than two seconds) starts the process of ejecting all of the discs in the changer.

(cid:96)(cid:96)

239

10 Audio

CD player/CD changer

NOTE

• The EJECT ALL function can only be used while the vehicle is at a standstill and will be cancelled if the vehicle begins to move.

• For reasons of traffic safety, the ejected CD must be removed within 12 seconds or it will be automatically drawn back into the slot and the CD player will enter pause mode. Press the CD button to restart the disc.

CD Pause When the audio system volume is turned off completely, the CD player will pause and will resume playing when the volume is turned up again.

Audio files In addition to playing normal music CDs, the CD player/changer can also play discs con- taining files in mp3 or wma format.

NOTE

Certain discs that are copy protected can- not be read by the player.

When a disc with audio files is inserted in the player, the player scans the disc's folders before it begins playing the files. The length of

10

240

time that this takes depends on the quality of the disc.

symbol and folders containing

Navigating the disc and playing tracks If a disc with audio files is in the CD player, press ENTER to display a list of folders on the disc. Use the up and down arrows in the navigation control (see the illustration on page 239) to move among the folders on the disc. Audio files have the these files have the ENTER to play a selected folder or a file. When the music file has been played, the player will continue to play the rest of the files in the current folder. When all of the files in the folder have been played, the player will auto- matically go to the next folder and play the files in it. Press the left or right arrow key on the naviga- tion control if the entire name of the current track does not fit in the display.

symbol. Press

Changing tracks Briefly press the left or right arrow keys on the MENU NAVIGATION CONTROL to skip to the previous or next track/file.

NOTE

The TUNING dial (6) (turn clockwise to go to the next track/file, or counterclockwise to go to the previous track/file) or the steering wheel keypad can also be used for this pur- pose.

Fast forward/back Press and hold down the left or right arrows keys in the MENU NAVIGATION CONTROL (or the corresponding keys on the optional steer- ing wheel keypad) to search within a track/file or the whole disc. The search continues for as long as the buttons are held down.

Random play This function plays the tracks/files on a CD (or on all of the CDs if the vehicle is equipped with the optional CD changer) in random order (shuffle).

Activating/deactivating the random function-CD player If a normal CD is being played: 1. Press MENU followed by ENTER. 2. Select Random and press ENTER. If a CD with audio files is being played: 1. Press MENU followed by ENTER. 2. Select Random and press ENTER.

3. Select Disc or Folder and press ENTER.

Activating/deactivating the random function-CD changer If a normal CD is being played: 1. Press MENU followed by ENTER. 2. Select Random and press ENTER. 3. Select Single disc or All discs and press

ENTER.

If a CD with audio files is being played: 1. Press MENU followed by ENTER. 2. Select Random and press ENTER. 3. Select Single disc or Folder and press

ENTER.

NOTE

CD changer only–you can only select the next random track/file on the current disc.

Press the EXIT button to stop random play. The random function is automatically deacti- vated when another disc is selected.

Disc text (CD changer only) Certain CDs contain information about the disc, such as the titles of the tracks, etc. This information can be shown in the display by activating the DISC TEXT function.

1. Press MENU. Select the menu for relevant

sound source and press ENTER.

2. Select Disc text in the menu and press

ENTER. > If information is stored on the disc, it will

now appear in the display.

To deactivate this function, select Disc text in the menu and press ENTER.

Scan This function plays the first 10 seconds of each track/file on the CD. • Press SCAN. • Press EXIT or SCAN to stop the scan func-

tion and listen to an entire track/file.

CD eject Single CD player Press the eject button (3) to eject the disc. CD changer This function makes it possible to eject a single disc, or to eject all of the discs in the changer. • Press the eject button (3) briefly to eject the

disc that is currently playing.

• A longer press (more than two seconds) starts the process of ejecting all of the discs in the changer.

10 Audio

CD player/CD changer

10

NOTE

• The Eject all function can only be used while the vehicle is at a standstill and will be cancelled if the vehicle begins to move.

• For reasons of traffic safety, the ejected CD must be removed within 12 seconds or it will be automatically drawn back into the slot and the CD player will enter pause mode. Press the CD button to restart the disc.

Compact disc care Keep the following in mind when playing/han- dling compact discs • Do not put tape or labels on the disc itself.

They could become stuck in the player. • CDR discs can cause listening problems due to the quality of the disc or recording equipment used.

• DualDisc: The audio side of a DualDisc (combined CD/DVD) does not meet CD specifications and may not play in your audio system.

• Keep the discs clean. Wipe them with a

soft, clean, lint-free cloth, working from the center outward. If necessary, dampen the cloth with a neutral soap solution. Dry thor- oughly before using.

(cid:96)(cid:96)

241

10 Audio

CD player/CD changer

• Never use cleaning spray or antistatic liq- uid. Use only cleaners specifically made for CDs.

• Use discs of the correct size only (3.5"

discs should never be used).

• Volvo does not recommend the use of

plastic outer rings on the disc.

• Condensation may occur on discs/optical components of the changer in cold winter weather. The disc can be dried with a clean, lint-free cloth. Optical components in the CD changer may, however, take up to one hour to dry off.

• Never attempt to play a damaged CD. • When not in use, the discs should be

stored in their covers. Avoid storing discs in excessive heat, direct sunlight or in dusty locations.

10

242

FM1/FM2 menu 1. RADIOTEXT ON/OFF 2. ADVANCED RADIO SETTINGS 3. AUDIO SETTINGS

AM menu 1. AUDIO SETTINGS

CD menu 1. RANDOM 2. AUDIO SETTINGS

CD changer menu 1. RANDOM