●Do not apply a heavy load to the front passenger seat or equipment (e.g.
seatback pocket).
●Do not put weight on the front passenger seat by putting your hands or
feet on the front passenger seat seatback from the rear passenger seat.
●Do not let a rear passenger lift the front passenger seat with their feet or
press on the seatback with their legs.
●Do not put objects under the front passenger seat. ●Do not recline the front passenger seatback so far that it touches a rear seat. This may cause the “AIR BAG OFF” indicator light to be illuminated, which indicates that the passenger’s airbags will not deploy in the event of a severe accident. If the seatback touches the rear seat, return the seat- back to a position where it does not touch the rear seat. Keep the front passenger seatback as upright as possible when the vehicle is moving. Reclining the seatback excessively may lessen the effectiveness of the seat belt system.
1-1. For safe use
51
WARNING
■Front passenger occupant classification system precautions
●If an adult sits in the front passenger seat, the “AIR BAG ON” indicator light is illuminated. If the “AIR BAG OFF” indicator is illuminated, ask the passenger to sit up straight, well back in the seat, feet on the floor, and with the seat belt worn correctly. If the “AIR BAG OFF” indicator still remains illuminated, either ask the passenger to move to the rear seat, or if that is not possible, move the front passenger seat fully rearward.
●When it is unavoidable to install a forward-facing child restraint system on the front passenger seat, install the child restraint system on the front pas- senger seat in the proper order. (P. 57) ●Do not modify or remove the front seats. ●Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately.
●Child restraint systems installed on the rear seat should not contact the
front seatbacks.
●Do not use a seat accessory, such as a cushion and seat cover, that cov-
ers the seat cushion surface.
●Do not modify or replace the upholstery of the front seat.
52
1-1. For safe use
Safety information for children
Observe the following precautions when children are in the vehi- cle. Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle’s seat belt.
● It is recommended that children sit in the rear seats to avoid acci-
dental contact with the shift lever, wiper switch, etc.
● Use the rear door child-protector lock or the window lock switch to avoid children opening the door while driving or operating the power window accidentally.
● Do not let small children operate equipment which may catch or pinch body parts, such as the power window, hood, back door, seats, etc.
WARNING
Never leave children unattended in the vehicle, and never allow children to have or use the key. Children may be able to start the vehicle or shift the vehicle into neutral. There is also a danger that children may injure themselves by playing with the cigarette lighter, the windows or other features of the vehicle. In addi- tion, heat build-up or extremely cold temperatures inside the vehicle can be fatal to children.
1-1. For safe use
53
Child restraint systems
A child restraint system for a small child or baby must itself be properly restrained on the seat with the lap portion of the lap/ shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.
Points to remember Studies have shown that installing a child restraint on a rear seat is much safer than installing one on the front passenger seat. ● Choose a child restraint system that suits your vehicle and is appro-
priate to the age and size of the child.
● For installation details, follow the instructions provided with the child
restraint system. General installation instructions are provided in this manual. (P. 57)
54
1-1. For safe use
Types of child restraints Child restraint systems are classified into the following 3 types according to the age and size of the child: Rear facing — Infant seat/
Forward facing — Convertible
convertible seat
seat
Booster seat
■Selecting an appropriate child restraint system
●Use a child restraint system appropriate for the child until the child becomes
large enough to properly wear the vehicle’s seat belt.
●If the child is too large for a child restraint system, sit the child on a rear seat
and use the vehicle’s seat belt. (P. 26)
1-1. For safe use
55
WARNING
■Child restraint precautions
●For effective protection in automobile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle’s interior. ●Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.
●Never install a rear-facing child restraint system on the front passenger seat even if the “AIR BAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child if the rear-facing child restraint system is installed on the front passenger seat.
●A forward-facing child restraint system may be installed on the front pas- senger seat only when it is unavoidable. A child restraint system that requires a top tether strap should not be used in the front passenger seat since there is no top tether strap anchor for the front passenger seat. Adjust the seatback as upright as possible and always move the seat as far back as possible even if the “AIR BAG OFF” indicator light is illumi- nated, because the front passenger airbag could inflate with considerable speed and force. Otherwise, the child may be killed or seriously injured.
●Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of sudden braking, sudden swerving or an accident.
56
1-1. For safe use
WARNING
■Child restraint precautions
●Do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front and rear pillars or roof side rails from which the SRS side airbags or SRS curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the SRS side airbags and curtain shield airbags inflate, and the impact could cause death or serious injury to the child.
●Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly secured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sudden stop, sudden swerve or an accident.
■When children are in the vehicle
Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.
■When the child restraint system is not in use
●Keep the child restraint system properly secured on the seat even if it is not in use. Do not store the child restraint system unsecured in the pas- senger compartment.
●If it is necessary to detach the child restraint system, remove it from the vehicle or store it securely in the luggage compartment. This will prevent it from injuring passengers in the event of a sudden stop, sudden swerve or an accident.
1
1-1. For safe use
57
Installing child restraints
Follow the child restraint system manufacturer’s instructions. Firmly secure child restraints to the rear seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Children) system.
Child restraint LATCH anchors
LATCH anchors are provided for the rear outer seats. (Buttons dis- playing the location of the anchors are attached to the seats.)
Seat belts equipped with a child restraint locking mechanism (ALR/ELR belts except driver’s seat belt) (P. 26)
Anchor brackets (for top tether strap)
An anchor bracket is provided for the each rear seats.
58
1-1. For safe use
Installation with LATCH system Type A
strap
Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the LATCH anchors. If the child restraint has a top tether strap, the top tether should be latched onto the top tether strap anchor. For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connec- tor system.
Canada only
Type B
Widen the gap between the seat cushion and seatback slightly. Latch the buckles onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connec- tor system.
Canada only
1-1. For safe use
59
Installing child restraints using a seat belt (child restraint lock function belt) ■ Rear-facing Infant seat/convertible seat
Place the child restraint sys- tem on the rear seat facing the rear of the vehicle.
Run the seat belt through the child restraint system and insert the buckle. Make sure that the belt is not twisted.
the plate
into
Fully extend the shoulder belt and allow it to retract to put it in lock mode. In lock mode, the belt cannot be extended.
60
1-1. For safe use
rear seat, allow
While pushing the child restraint system down into the the shoulder belt to retract until the child restraint system is securely in place. After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
■ Forward-facing Convertible seat
Remove the head restraint. (P. 104) Place the child restraint sys- tem on the seat facing the front of the vehicle.
Run the seat belt through the child restraint system and insert the buckle. Make sure that the belt is not twisted.
the plate
into
1-1. For safe use
61
Fully extend the shoulder belt and allow it to retract to put it in lock mode. In lock mode, the belt cannot be extended.
retract until
While pushing the child restraint system into the rear seat, allow the shoulder belt to the child restraint system is securely in place. After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. (P. 63)
62
1-1. For safe use
■ Booster seat
Place the child restraint sys- tem on the seat facing the front of the vehicle.
Sit the child in the child restraint system. Fit the seat belt to the child restraint sys- tem according to the manu- instructions and facturer’s insert the buckle. Make sure that the belt is not twisted. Check that the shoulder belt is correctly positioned over the child’s shoulder and that the lap belt is as low as possible. (P. 26)
the plate
into
Removing a child restraint installed with a seat belt Push the buckle release button and fully retract the seat belt.
1-1. For safe use
63
Child restraint systems with a top tether strap
Remove the luggage cover. (P. 188) Remove the head restraint. (P. 104) Secure the child restraint system using the LATCH anchors or a seat belt. Open the anchor bracket cover, latch the hook onto the anchor bracket and tighten the top tether strap. Make sure the top tether strap is securely latched.
Reinstall the luggage cover.
■Laws and regulations pertaining to anchorages
The LATCH system conforms to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to conform to the SAE J1819.
64
1-1. For safe use
WARNING
■When installing a booster seat
To prevent the belt from going into ALR lock mode, do not fully extend the shoulder belt. ALR mode causes the belt to tighten only. This could cause injury or discomfort to the child. (P. 29)
■When installing a child restraint system
Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be seriously injured or even killed in the event of a sudden braking, sudden swerving or an accident. ●If the driver’s seat interferes with the child restraint system and prevents it from being attached correctly, attach the child restraint system to the rear right seat.
●Adjust the front passenger seat so that it does not interfere with the child restraint system.
●Only put a forward-facing child restraint system on the front passenger seat when unavoidable. When installing a forward-facing child restraint system on the front passenger seat, move the seat as far back as pos- sible even if the “AIR BAG OFF” indica- tor light is illuminated. Failure to do so may result in death or serious injury if the airbags deploy (inflate).
●When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child’s shoulder. The belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder. Failure to do so may result in death or serious injury in the event of a sudden braking, sudden swerving or an accident.
1-1. For safe use
65
WARNING
■When installing a child restraint system
●Ensure that the belt and plate are securely locked and the seat belt is not
twisted.
●Shake the child restraint system left and right, and forward and backward
to ensure that it has been securely installed.
●After securing a child restraint system, never adjust the seat. ●Follow all installation instructions provided by the child restraint system
manufacturer.
●When a child restraint system with a top tether strap is installed, do not install the head restraint. The head restraint may interfere with the top tether strap preventing secure installation of the child restraint system.
●Make sure to properly store the removed head restraint in a secure place
when you use the child restraint system on the rear seat.
●When using the rear right seat for the child restraint system, do not sit in the rear center seat. Seat belt function may be impaired, such as being positioned overly high or loose-fitting, which may result in death or serious injury in the event of sudden braking or an accident.
■Do not use a seat belt extender
If a seat belt extender is used when installing a child restraint system, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of sud- den braking, sudden swerving or an accident.
■To correctly attach a child restraint system to the anchors
When using the LATCH anchors, be sure that there are no foreign objects around the anchors and that the seat belt is not caught behind the child restraint system. Make sure the child restraint system is securely attached, or it may cause death or serious injury to the child or other passengers in the event of a sudden braking, sudden swerve or an accident.
66
1-1. For safe use
Exhaust gas precautions
Harmful substances to the human body are included in exhaust gases if inhale.
WARNING
Exhaust gases contain harmful carbon monoxide (CO), which is colorless and odorless. Observe the following precautions. Failure to do so may cause exhaust gases enter the vehicle and may lead to an accident caused by light-headedness, or may lead to death or a serious health hazard. ■Important points while driving
●Keep the back door closed. ●If you smell exhaust gases in the vehicle even when the back door is closed, open the windows and have the vehicle inspected at your Toyota dealer as soon as possible.
■When parking
●If the vehicle is in a poorly ventilated area or a closed area, such as a
garage, stop the engine.
●Do not leave the vehicle with the engine running for a long time.
If such a situation cannot be avoided, park the vehicle in an open space and ensure that exhaust fumes do not enter the vehicle interior.
●Do not leave the engine running in an area with snow build-up, or where it is snowing. If snowbanks build up around the vehicle while the engine is running, exhaust gases may collect and enter the vehicle.
■Exhaust pipe
The exhaust system needs to be checked periodically. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer.
1-2. Theft deterrent system
67
Engine immobilizer system
The vehicle’s keys have built-in transponder chips that prevent the engine from starting if a key has not been previously regis- tered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehi- cle. This system is designed to help prevent vehicle theft but does not guarantee absolute security against all vehicle thefts.
The system begins operating after the key has been removed from the engine switch. The system is canceled after the registered key has been inserted into the engine switch.
■System maintenance
The vehicle has a maintenance-free type engine immobilizer system.
■Conditions that may cause the system to malfunction
●If the grip portion of the key is in contact with a metallic object ●If the key is in close proximity to or touching a key to the security system
(key with a built-in transponder chip) of another vehicle
: If equipped
68
1-2. Theft deterrent system
■Certifications for the engine immobilizer system
U.S.A. FCC ID: PSIRI-43BTY This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.
NOTICE
■To ensure the system operates correctly
Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.
1-2. Theft deterrent system
69
Theft prevention labels (except Canada)
These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recov- ery of parts from stolen vehicles. Do not remove under penalty of law.
70
1-2. Theft deterrent system
71
Instrument cluster
2.
Instrument cluster
Warning lights and
indicators .......................... 72
Gauges and meters ............ 76
Multi-information display ..... 78
72
2. Instrument cluster
Warning lights and indicators
The warning lights and indicators on the instrument cluster, cen- ter panel and dashboard inform the driver of the status of the vehicle’s various systems. For the purpose of explanation, the following illustration dis- plays all warning lights and indicators illuminated.
This illustration represents a meter with a tachometer and may differ from the look of the meter without a tachometer.
2. Instrument cluster
73
Warning lights Warning lights inform the driver of malfunctions in the indicated vehi- cle’s systems.
*1
(Except Canada)
*1
(Canada)
*1
*1
*1
*1
(Red)
(Except Canada)
*1
(Canada)
*1
*1
(Except Canada)
*1
(Canada)
Brake system warning light (P. 272)
Brake system warning light (P. 272)
Charging system warn- ing light (P. 272)
*1
*1, 3
*2
(Yellow)
Electric power steering system warning light (P. 273)
Slip indicator light (P. 273)
Cruise control indicator light (P. 274)
Low engine oil pressure warning light (P. 272)
Open door warning light (P. 274)
High engine temperature light (P. 272)
coolant warning
Malfunction lamp (P. 273)
indicator
Malfunction lamp (P. 273)
indicator
SRS warning light (P. 273)
ABS warning light (P. 273)
ABS warning light (P. 273)
*1
(Except Canada)
*1
(If equipped)
*1
(Except Canada)
Low fuel level warning light (P. 274)
Driver’s and front pas- senger’s belt reminder light (P. 274)
seat
Tire pressure warning light (P. 274)
Low windshield washer fluid warning light (P. 275)
Maintenance required reminder light (P. 275)
74
2. Instrument cluster
*1: These lights turn on when the engine switch is turned to the “ON” position to indicate that a system check is being performed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.
*2: If equipped *3: The light flashes to indicate that the system is operating and come on to
indicate a malfunction.
Indicators The indicators inform the driver of the operating state of the vehicle’s various systems.
Turn signal indicator (P. 142)
Headlight high beam indicator (P. 146)
Front fog light indicator (P. 147)
Low engine coolant tem- perature indicator
Eco Driving Light (P. 120)
Indicator
Cruise control indicator (P. 158)
*2
*3
(Blue)
*1, 4
*2
(Green)
*2
*1, 5
*1
*1
*1, 6
*1, 6
Cruise indicator (P. 158)
control
“SET”
Slip indicator (P. 163)
“TRAC OFF” indicator (P. 163)
VSC OFF indicator (P. 164)
“AIR BAG ON” indicator (P. 46)
“AIR BAG OFF” indicator (P. 46)
2. Instrument cluster
75
*1: These lights turn on when the engine switch is turned to the “ON” position
to indicate that a system check is being performed. They will turn off after
the engine is started, or after a few seconds. There may be a malfunction
in a system if a light does not come on, or if the lights do not turn off. Have
the vehicle inspected by your Toyota dealer.
*2: If equipped *3: The light turns on to indicate the engine coolant temperature is low. *4: Vehicles with an automatic transmission *5: The light flashes to indicate that the system is operating. *6: This light illuminates on the center panel.
WARNING
■If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not come on when you start the engine, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immedi- ately if this occurs.
NOTICE
■To prevent damage to the engine and its components
The engine may be overheating if the high engine coolant temperature warning light flashes or turns on. In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (P. 300)
76
2. Instrument cluster
Gauges and meters
Tachometer (if equipped)
Displays the engine speed in revolutions per minute.
Speedometer
Displays the vehicle speed.
Fuel gauge (if equipped)
Displays the quantity of fuel remaining in the tank.
Display change button
P. 79
Multi-information display
Presents the driver with a variety of driving-related data. (P. 78)
Clock adjusting buttons
P. 80
2. Instrument cluster
77
Instrument panel light control The brightness of the instrument panel lights can be adjusted.
Brighter Darker
■The meters and display illuminate when The engine switch is in the “ON” position.
NOTICE
■To prevent damage to the engine and its components
On vehicles with a tachometer, do not let the indicator needle of the tachom- eter enter the red zone, which indicates the maximum engine speed.
78
2. Instrument cluster
Multi-information display
The multi-information display presents the driver with a variety of driving-related data including the clock.
Display contents
Type A
Type B
Type C
Clock (P. 80) Outside temperature display (P. 81) Shift position and gear step position indicator (P. 139) Drive information (P. 79) Fuel gauge
2. Instrument cluster
79
Changing the display Items displayed can be switched by pressing the display change button.
Drive information ■ Odometer
Displays the total distance the vehicle has been driven.
■ Trip meters
Displays the distance the vehicle has been driven since the meter was last reset. Trip meters “A” and “B” can be used to record and display different distances independently. Pressing and holding the display change button while the trip meter is displayed will reset the trip meter to “0”.
■ Driving range
Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that dis- played.
• When only a small amount of fuel is added to the tank, the display may
not be updated.
When refueling, turn the engine switch to the “LOCK” position. If the vehi- cle is refueled without turning the engine switch to the “LOCK” position, the display may not be updated.
80
2. Instrument cluster
■ Average fuel consumption
Displays the average fuel consumption since the function was reset. • The function can be reset by pressing and holding the display change
button when the average fuel consumption is displayed.
• Use the displayed average fuel consumption as a reference.
■ Instantaneous fuel consumption
Displays the instantaneous of fuel consumption.
■ Average vehicle speed
Displays the average vehicle speed since the engine was last started.
Eco Driving Indicator Light customization (Vehicles with an auto- matic transmission) Eco Driving Indicator Light can be activated or deactivated by press- ing the display change button when the Eco Driving Indicator Light customization display is displayed.
To change the Eco Driving Indicator Light customization display, display the odometer and press and hold the display change button until the display changes. After customization, press the display change button for more than 2 sec- onds to return to the odometer.
Clock The clock can be adjusted by pressing the buttons.
Adjust the hours Adjust the minutes
2. Instrument cluster
81
Outside temperature display The temperature display shows temperatures within the range of -40°F (-40°C) and 122°F (50°C). ■ Display
In the following situations, the correct outside temperature may not be displayed, or the display may take longer than normal to change: ● When the vehicle is stopped, or moving at low speeds (less than
16 mph [25 km/h])
● When the outside temperature has changed suddenly (at the
entrance/exit of a garage, tunnel, etc.)
■ When “” or “E” is displayed
The system may be malfunctioning. Take your vehicle to your Toy- ota dealer.
■When disconnecting and reconnecting battery terminals
The following information data will be reset. ●Driving range ●Average fuel consumption ●Average vehicle speed ●Clock data
■Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is characteristic of liquid crystal display, and there is no problem continuing to use the display.
NOTICE
■The multi-information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the display monitor may respond slowly, and display changes may be delayed.
82
2. Instrument cluster
83
Operation of each component
3-1. Key information
Keys .................................... 84
3-2. Opening, closing
and locking the doors
Side doors........................... 89
Back door............................ 94
3-3. Adjusting the seats
Front seats .......................... 98
Rear seats......................... 101
Head restraints.................. 104
3-4. Adjusting the steering
wheel and mirrors
Steering wheel .................. 107
Inside rear view mirror ...... 109
Outside rear view
mirrors............................. 111
3-5. Opening and closing
the windows
Power windows ................. 113
84
3-1. Key information
Keys
The keys The following keys are provided with the vehicle. Vehicles without an engine immobilizer system (type A)
Master keys Key number plate
Vehicles without an engine immobilizer system (type B)
Master key (with a wireless remote control function) Operating the wireless remote con- trol function (P. 89) Master keys (without a wireless remote control function) Key number plate
Vehicles with an engine immobilizer system (type A)
Master keys Key number plate
3-1. Key information
85
Vehicles with an engine immobilizer system (type B)
Master keys Operating the wireless remote con- trol function (P. 89) Key number plate
Vehicles with an engine immobilizer system (type C)
Master keys Operating the wireless remote con- trol function (P. 89) Key number plate
Wireless remote control (if equipped) Type A
Locks all the doors (P. 89) Sounds the alarm (press and hold) Unlocks all the doors (P. 89) Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors.
86
3-1. Key information
Type B
Locks all the doors (P. 89) Unlocks all the doors (P. 89) Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors. Sounds the alarm (press and hold)
■If you lose your keys
New genuine keys can be made by your Toyota dealer using the other key and the key number stamped on your key number plate. Keep the plate in a safe place such as your wallet, not in the vehicle.
■When riding in an aircraft
When bringing a key with wireless remote control function onto an aircraft, make sure you do not press any buttons on the key while inside the aircraft cabin. If you are carrying a key in your bag etc., ensure that the buttons are not likely to be pressed accidentally. Pressing a button may cause the key to emit radio waves that could interfere with the operation of the aircraft.
■Panic mode
When is pressed for longer than about 1 second, an alarm will sound intermit- tently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, press any button on the wireless remote control.
3-1. Key information
87
■Conditions affecting operation (wireless remote control)
The wireless remote control function may not operate normally in the follow- ing situations: ●When the wireless key battery is depleted ●Near a TV tower, electric power plant, gas station, radio station, large dis- play, airport or other facility that generates strong radio waves or electrical noise
●When carrying a portable radio, cellular phone or other wireless communi-
cation devices
●When the wireless key is in contact with, or is covered by a metallic object ●When other wireless keys (that emit radio waves) are being used nearby ●If window tint with a metallic content or metallic objects are attached to the
rear window
■Key battery depletion
If the wireless remote control function does not operate, the battery may be depleted. Replace the battery when necessary.
■Customization that can be configured at your Toyota dealer Settings (e.g. wireless remote control system) can be changed. (Customizable features: P. 333)
■Certification for the wireless remote control
U.S.A. FCC ID: HYQ23AAA FCC ID: HYQ12BBY NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Canada NOTE: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.
88
3-1. Key information
NOTICE
■To prevent key damage
Observe the following: ●Do not subject the keys to strong shocks, expose them to high tempera-
tures by placing them in direct sunlight, or get them wet.
●Do not expose the keys to electromagnetic materials or attach any mate-
rial that blocks electromagnetic waves to the key surface.
●Do not disassemble the wireless remote control key.
3-2. Opening, closing and locking the doors
89
Side doors
Unlocking and locking the doors from the outside The vehicle can be locked and unlocked using the keys, wireless remote control or door lock switches. ◆ Wireless remote control (if equipped) Type A
Locks all the doors Sounds the alarm (press and hold) Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors.
Type B
Locks all the doors Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the button again within 3 seconds unlocks the other doors. Sounds the alarm (press and hold)
90
3-2. Opening, closing and locking the doors
◆ Keys
Turning the key operates the doors as follows:
■ Driver’s door
Locks all the doors Unlocks all the doors Turning the key unlocks the driver’s door. Turning the key again unlocks the other doors.
■ Front passenger’s door
Locks all the doors Unlocks all the doors
■Operation signals (vehicles with a wireless remote control)
The emergency flashers flash to indicate that the doors have been locked/ unlocked. (Locked: once; Unlocked: twice)
■Security feature (vehicles with a wireless remote control)
If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again.
3-2. Opening, closing and locking the doors
91
Unlocking and locking the doors from the inside ◆ Door lock switch
Unlocks all the doors Locks all the doors
◆ Inside door lock buttons
Locks the doors Unlocks the doors The front doors can be opened by pulling inside handle even if the inside door lock but- ton is in the lock position.
the
Locking the front door from the outside without a key
Move the inside door lock button to the lock position. Close the door.
The door cannot be locked if either of the front doors is open and the key is in the engine switch.
92
3-2. Opening, closing and locking the doors
Rear door child-protector lock (5-door models only) The door cannot be opened from inside the vehicle when the lock is set.
Unlock Lock These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.
■Conditions affecting the operation of the wireless remote control
P. 87
■Customization
Settings (e.g. unlocking function using a key) can be changed. (Customizable features P. 333)
3-2. Opening, closing and locking the doors
93
WARNING
■To prevent an accident
Observe the following precautions while driving the vehicle. Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ●Always use a seat belt. ●Always lock all the doors. ●Ensure that all the doors are properly closed. ●Do not pull the inside handle of the doors while driving.
The doors may be opened and the passengers are thrown out of the vehi- cle and it may result in serious injury or death. Be especially careful for the front doors, as the doors may be opened even if the inside lock buttons are in locked position.
●Set the rear door child-protector locks when children are seated in the rear
seats.
94
3-2. Opening, closing and locking the doors
Back door
The back door can be locked/unlocked and opened by the fol- lowing procedures.
Unlocking and locking the back door ◆ Door lock switch
P. 91
◆ Wireless remote control (if equipped)
P. 89
◆ Keys
From the back door (vehicles with a back door key cylinder):
Unlocks all the doors Locks all the doors
From the driver’s door: P. 90
When closing the back door Lower the back door using the back door handle, and make sure to push the back door down from the outside to close it.
3-2. Opening, closing and locking the doors
95
■Operation signals (vehicles with a wireless remote control)
P. 90
■Security feature (vehicles with a wireless remote control)
P. 90
■Luggage compartment light
The luggage compartment lights turn on when the back door is opened.
WARNING
Observe the following precautions. Failure to do so may result in death or serious injury. ■Before driving
●Make sure that the back door is fully closed. If the back door is not fully closed, it may open unexpectedly while driving and hit near-by objects or luggage in the luggage compartment may be thrown out, causing an acci- dent.
●Do not allow children to play in the luggage compartment.
If a child is accidentally locked in the luggage compartment, they could have heat exhaustion or other injuries.
●Do not allow a child to open or close the back door.
Doing so may cause the back door to open unexpectedly, or cause the child’s hands, head, or neck to be caught by the closing back door.
■Important points while driving
●Keep the back door closed while driving.
If the back door is left open, it may hit near-by objects or luggage in the luggage compartment may be thrown out, causing an accident.
●Never let anyone sit in the luggage compartment. In the event of sudden
braking or a collision, they are susceptible to death or serious injury.
96
3-2. Opening, closing and locking the doors
WARNING
■Operating the back door
Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in death or serious injury. ●Remove any heavy loads, such as snow and ice, from the back door before opening it. Failure to do so may cause the back door to suddenly shut again after it is opened.
●When opening or closing the back door, thoroughly check to make sure
the surrounding area is safe.
●If anyone is in the vicinity, make sure they are safe and let them know that
the back door is about to open or close.
●Use caution when opening or closing the back door in windy weather as it
may move abruptly in strong wind.
●The back door may suddenly shut if it is not opened fully. It is more difficult to open or close the back door on an incline than on a level surface, so beware of the back door unexpectedly opening or closing by itself. Make sure that the back door is fully open and secure before using the luggage com- partment.
●When closing the back door, take extra care to prevent your fingers, etc., from being caught.
●When closing the back door, make sure to press it lightly on its outer surface. If the back door handle is used to fully close the back door, it may result in hands or arms being caught.
●Do not pull on the back door damper stay to close the back door, and do
not hang on the back door damper stay. Doing so may cause hands to be caught or the back door damper stay to break, causing an accident.
●If a bicycle carrier or similar heavy object is attached to the back door, it may suddenly shut again after being opened, causing someone’s hands, head or neck to be caught and injured. When installing an accessory part to the back door, using a genuine Toyota part is recommended.
3-2. Opening, closing and locking the doors
97
NOTICE
■Back door damper stays
The back door is equipped with damper stays that hold the back door in place. Observe the following precautions. Failure to do so may cause damage to the back door damper stay, resulting in malfunction. ●Do not attach any foreign objects, such as stickers, plastic sheets, or adhesives to the damper stay rod.
●Do not touch the damper stay rod with
gloves or other fabric items.
●Do not attach any accessories other than genuine Toyota parts to the back door.
●Do not place your hand on the damper
stay or apply lateral forces to it.
98
3-3. Adjusting the seats
Front seats
Adjustment procedure Driver’s seat
Seat position adjustment lever Seatback angle adjustment lever Vertical height adjustment lever (if equipped)
Front passenger’s seat