Login- Download PDF Manual
-
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors Back door
The back door can be opened using the back door opener. The back door can be locked and unlocked using the entry function (vehicles with smart key system), wireless remote control or door lock switch. In addition, the power back door (if equipped) can be opened using the power back door switch or wireless remote control. ■ Unlocking and locking the back door
Entry function (vehicles with smart key system) P. 30
Wireless remote control P. 45
Door lock switch P. 50■ Opening the back door from outside the vehicle
Back door opener
Raise the back door while pushing up the back door opener switch.
Wireless remote control (vehicles with power back door) P. 45
56
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
■ Opening the back door from inside the vehicle (vehicles
with power back door)
Push and hold the switch to open/close. Pressing the switch again while the power back door is operating will cause the opera- tion to reverse. However, the reverse opera- tion cannot be performed for the first second after pressing the switch to operate the door.
Lower the back door using the back door handle, and make sure to push the back door down from the outside to close it.
Be careful not to pull the back door sideways when closing the back door with the handle.
57
When closing the back door
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
Power back door switch (vehicles with power back door)
Push the switch to close.
Pressing the switch again while the power back door is closing will cause it to open again. However, the reverse operation cannot be performed for the first second after pressing the switch to close the door.
The back door can be opened even if it is locked. Lock the back door again when you leave the vehicle. The back door will not lock auto- matically after it has been opened and then closed. A buzzer sounds and the emergency flashers flash twice to indicate that the back door has been opened/closed.
58
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
Canceling the power back door system (vehicles with power back door)
Turn the main switch to disable the power back door system.
Inoperative Operative The back door cannot be oper- ated even with the wireless remote control or power back door switch. A buzzer will sound twice if the power back door switch is pressed while the power back door system is inoperative.
59
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
■The power back door can be opened/closed when (vehicles with power
back door)
Vehicles with smart key system ●The “ENGINE START STOP” switch is in IGNITION ON mode, and
the shift lever is in “P”.
●The “ENGINE START STOP” switch is in OFF or ACCESSORY
mode.
Vehicles without smart key system ●The engine switch is in the “ON” position, and the shift lever is in “P”. ●The engine switch is in the “LOCK” or “ACC” position.
■Jam protection function (vehicles with power back door)
If anything obstructs the power back door while it is closing/opening, the back door will automatically operate in the opposite direction.
■If the power back door does not work (vehicles with power back door) The back door must be initialized. To initialize, close the back door com- pletely by hand.
■Back door closer
In the event that the back door is left slightly open, the back door closer will automatically close it to the fully closed position.
60
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
CAUTION
■While driving
●Keep the back door closed while driving.
If the back door is left open, it may hit near-by objects while driving or lug- gage may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard. Make sure to close the back door before driving.
●Before driving the vehicle, make sure that the back door is fully closed. If the back door is not fully closed, it may open unexpectedly while driving, causing an accident.
●Never let anyone sit in the luggage compartment. In the event of sudden
braking or a collision, they are susceptible to death or serious injury.
■When children are in the vehicle Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not allow children to play in the luggage compartment.
If a child is accidentally locked in the luggage compartment, they could have heat exhaustion or other injuries.
●Do not allow a child to open or close the back door.
Doing so may cause the back door to move unexpectedly, or cause the child’s hands, head, or neck to be caught by the closing back door.
61
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
CAUTION
■Operating the back door
Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in death or serious injury. ●Remove any heavy loads, such as snow and ice, from the back door before opening it. Failure to do so may cause the back door to suddenly shut again after it is opened.
●When opening or closing the back door, thoroughly check to make sure
the surrounding area is safe.
●If anyone is in the vicinity, make sure they are safe and let them know that
the back door is about to open or close.
●Use caution when opening or closing the back door in windy weather as it
may move abruptly in strong wind.
●The back door may suddenly shut if it is not opened fully. It is more difficult to open or close the back door on an incline than on a level surface, so beware of the back door unexpectedly opening or closing by itself. Make sure that the back door is fully open and secure before using the luggage com- partment.
62
VENZA_OM_OM73019U_(U)
1
CAUTION
1-2. Opening, closing and locking the doors
●When closing the back door, take extra care to prevent your fingers etc. from being caught.
●When closing the back door, make sure to press it lightly on its outer surface. If the back door handle is used to fully close the back door, it may result in hands or arms being caught.
●Do not pull on the back door damper stay to close the back door, and do
not hang on the back door damper stay. Doing so may cause hands to be caught or the back door damper stay to break, causing an accident.
●If a bicycle carrier or similar heavy object is attached to the back door, it may suddenly shut again after being opened, causing someone’s hands, head or neck to be caught and injured. When installing an accessory part to the back door, using a genuine Toyota part is recommended.
■Back door closer
It
●In the event that the back door is left slightly open, the back door closer will automatically close it to the fully closed position. takes several seconds before the back door closer begins to operate. Be careful not to catch fingers or anything else in the back door, as this may cause bone fractures or other serious injuries.
●Use caution when using the back door closer as it still operates when the
power back door system is cancelled.
63
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
CAUTION
■Power back door (if equipped)
Observe the following precautions when operating the power back door. Failure to do so may cause death or serious injury. ●Check the safety of the surrounding area to make sure there are no obsta-
cles or anything that could cause any of your belongings to get caught.
●If anyone is in the vicinity, make sure they are safe and let them know that
the back door is about to open or close.
●On an incline, the back door may suddenly shut after it opens. Make sure
the back door is fully open and secure.
●In the following situations, the power back door may detect an abnormality and automatic operation may be stopped. In this case, the back door has to be operated manually. Take extra care when on an incline, as the back door may open or close abruptly. • When the back door contacts an obstacle • Vehicles with smart key system:
When the battery voltage suddenly drops, such as when the “ENGINE START STOP” switch is turned to IGNITION ON mode or the engine is started during automatic operation Vehicles without smart key system: When the battery voltage suddenly drops, such as when the engine switch is turned to the “ON” position or the engine is started during automatic operation
●If a bicycle carrier or similar heavy object is attached to the back door, the power back door may not operate, causing itself to malfunction, or the back door may suddenly shut again after being opened, causing some- one’s hands, head or neck to be caught and injured. When installing an accessory part to the back door, using a genuine Toyota part is recom- mended.
64
VENZA_OM_OM73019U_(U)
1
1-2. Opening, closing and locking the doors
CAUTION
■Jam protection function (vehicles with power back door)
Observe the following precautions. Failure to do so may cause death or serious injury. ●Never use any part of your body to intentionally activate the jam protection
function.
●The jam protection function may not work if something gets caught just before the back door fully closes. Be careful not to catch fingers or any- thing else.
●The jam protection function may not work depending on the shape of the
object that is caught. Be careful not to catch fingers or anything else.
NOTICE
■Back door damper stays
The back door is equipped with damper stays that hold the back door in place. Observe the following precautions. Failure to do so may cause damage to the back door damper stay, resulting in malfunction.
Damper stay
●Do not attach any foreign objects, such as stickers, plastic sheets, or adhesives to the damper stay rod.
●Do not touch the damper stay rod with
gloves or other fabric items.
●Do not attach any accessories other than genuine Toyota parts to the back door.
●Do not place your hand on the damper
stay or apply lateral forces to it.
65
VENZA_OM_OM73019U_(U)
1-2. Opening, closing and locking the doors
NOTICE
■To prevent back door closer malfunction
Do not apply excessive force to the back door while the back door closer is operating.
■To prevent damage to the power back door (vehicles with power back
door) ●Make sure that there is no ice between the back door and frame that would prevent movement of the back door. Operating the power back door when excessive load is present on the back door may cause a malfunc- tion.
●Do not apply excessive force to the back door while the power back door
is operating.
●Take care not to damage the sensors (installed on the right and left edges of the power back door) with a knife or other sharp object. If the sensor is disconnected, the power back door will not operate in automatic operation.
66
VENZA_OM_OM73019U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel) Front seats
Power seat
angle
control
Seat position fore/aft control switch Seatback switch Seat cushion (front) angle control switch (driver’s side only) Vertical switch (driver’s side only) Lumbar switch
support
height
control
control
Manual seat
Seat position fore/aft adjust- ment lever Seatback angle adjustment lever
67
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
Active head restraints
When the occupant’s lower back presses against the seatback during a rear-end collision, the head restraint moves slightly for- ward and upward to help reduce the risk of whiplash on the seat occupant.
■Active head restraints
Even small forces applied to the seatback may cause the head restraint to move. Pushing up a locked head restraint forcibly may make the inner struc- ture of the head restraint appear. This does not indicate a problem.
During rear-end collision
Inner structure
68
VENZA_OM_OM73019U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Seat adjustment
●Be careful that the seat does not hit passengers or luggage. ●Do not recline the seat more than necessary when the vehicle is in motion
to reduce the risk of sliding under the lap belt. If the seat is too reclined, during an accident the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury.
●Manual seat only: After adjusting the seat, make sure that the seat is
locked in position.
69
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats
Seatback angle adjustment lever
Pull up the lever until the lock is completely released.
Folding down the rear seatbacks
■ Before folding down the rear seatbacks STEP 1
Stow the seat belt buckles and lower the head restraints to the lowest position.
70
VENZA_OM_OM73019U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
STEP 2
Pass the outer seat belts and plates the seat belt hangers.
through
This prevents the shoulder belt from being damaged. Make sure that the seat belts are removed from the hangers before using them.
■ Folding down the rear seatbacks
From inside
Fold down the seatback while pulling seatback angle adjustment lever.
the
Pull up the lever until the lock is completely released.
Pull the lever.
For left side rear seatback For right side and center rear seatback
71
From outside
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Seat adjustment
Do not recline the seat more than necessary when the vehicle is in motion, to reduce the risk of sliding under the lap belt. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of an accident.
■Before folding down a rear seat
Do not fold down a rear seat when there are passengers sitting in the rear seats or when there is luggage placed on the rear seats.
■When returning the seatbacks to their original position
Observe the following precautions. Failure to do so may result in death or serious injury. ●Be careful not to get your hands pinched in the seat. ●Make sure the seatbacks are securely locked by lightly rocking it back and
forth.
●Check that the seat belts are not twisted or caught under the seat. ●Arrange the seat belts in the proper positions for ready use.
NOTICE
■When folding down the rear seatbacks
The seat belts and buckles must be stowed.
72
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Driving position memory
Your preferred driving position (the position of the driver’s seat and angle of the outside rear view mirrors) can be memorized and recalled by pressing a button. It is also possible to set this function to activate automatically when the doors are unlocked. Two different driving positions can be entered into memory. ■ Entering a position to memory STEP 1
Check that the shift lever is in P. Vehicles with smart key system: Turn the “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system: Turn the engine switch is in the “ON” position. Adjust the driver’s seat and outside rear view mirrors to the desired positions.
STEP 2
STEP 3
STEP 4
While pressing the “SET” but- ton, or within 3 seconds after the “SET” button is pressed, press button “1” or “2” until the signal beeps.
the selected button has If already been preset, the previ- ously recorded position will be overwritten.
: If equipped 73
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
STEP 2
■ Recalling the memorized position Check that the shift lever is in P. STEP 1
Vehicles with smart key system: Turn the “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system: Turn the engine switch is in the “ON” position.STEP 3
Press button “1” or “2” to recall the desired position.
74
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
Power easy access system
The auto away/return function enables easy access by activat- ing when the driver attempts to enter or exit the vehicle.
Auto away function (exiting the vehicle) When all of the following actions have been performed, the seat will move backward: ● The shift lever has been shifted to “P”. ● Vehicles with smart key system: The “ENGINE START STOP”
switch has been turned off. Vehicles without smart key system: The key is removed from the engine switch.
● The driver’s seat belt has been unfastened. Auto return function (entering the vehicle) When either of the following actions has been performed, the seat will move forward: ● Vehicles with smart key system: The “ENGINE START STOP”
switch has been turned to ACCESSORY mode. Vehicles without smart key system: The engine switch has been turned to the “ACC” position.
● The driver’s seat belt has been fastened.
75
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■Operating the driving position memory after turning the “ENGINE START STOP” switch off (vehicles with smart key system) or the key is removed from the engine switch (vehicle without smart key system) Memorized seat positions can be activated up to 180 seconds after the driver’s door is opened and another 60 seconds after it is closed again.
■Stopping seat position recall operation part-way through
Perform any of the following operations: ●Press the “SET” button. ●Press button “1” or “2”. ●Adjust the seat using the switches.
■Correct seat position
When the seat is in the most forward or most backward position, and the seat is being moved in those directions, the system may not correctly recog- nize the current position and the memorized position will not be correctly recalled.
■The auto away function for exiting the driver’s seat
If the seat is already close to the rearmost position, the auto away function may not operate when the driver exits the vehicle.
■If the battery is disconnected
The memorized positions are erased when the battery is disconnected.
■Customization
The auto away function for driver’s seat may be disabled. (Customizable features: P. 519)
76
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Seat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear passenger or squeeze your body against the steering wheel.
77
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints
Head restraints are provided for all seats.
Front and rear outboard seats
Lock release button
Rear center seat (fabric seat)
Lock release button
Rear center seat (leather seat)
Lock release button
Vertical adjustment
Up Pull the head restraint up. Down Push the head restraints down while pressing the lock release button.
Vertical adjustment
Down Up Push the head restraint up or down while pressing the lock release button.
Vertical adjustment
Down Push the head restraint down while pressing the lock release button. Up Pull the head restraint up.
78
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■Adjusting the height of the head restraints
Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.
■Adjusting the rear center seat head restraint
Always raise the head restraint one level from the stowed position when using.
■Removing the head restraints
Pull the head restraint up while pressing the lock release button.
■Installing the head restraints
Align the head restraint with the installa- tion holes and push it down to the lock position. Press and hold the lock release button when lowering the head restraint.
79
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Head restraint precautions
Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. ●Use the head restraints designed for each respective seat. ●Adjust the head restraints to the correct position at all times. ●After adjusting the head restraints, push down on them and make sure
they are locked in position.
●Do not drive with the head restraints removed.
80
VENZA_OM_OM73019U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts
Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts
Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoul- der. Position the lap belt as low as possible over the hips. Adjust the position of the seatback. Sit up straight and well back in the seat. Do not twist the seat belt.
■ Fastening and releasing the seat belt
Fastening the belt Push the tab into the buckle until a clicking sound is heard. Releasing the belt Press the release button.
Release button
81
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■ Adjusting the height of the belt (front seats)
Down Up
Move the height adjuster up and down as needed until you hear a click.
Seat belt pretensioners (front seats)
The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal or side collision.
The pretensioner does not acti- vate in the event of a minor frontal impact, a minor side impact, a rear impact or a vehicle rollover.
82
VENZA_OM_OM73019U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
■Emergency locking retractor (ELR)
The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend, and you can move around fully.
■Automatic locking retractor (ALR)
When a passenger’s shoulder belt is completely extended and then retracted even slightly, the belt is locked in that position and cannot be extended. This feature is used to hold the child restraint system (CRS) firmly. To free the belt again, fully retract the belt and then pull the belt out once more. (P. 145)
■When not using the rear outboard seat belts
Pass the outer seat belts and plates through the seat belt hangers to prevent the shoulder belts from being damaged.
■Child seat belt usage
The seat belts of your vehicle were principally designed for persons of adult size. ●Use a child restraint system appropriately for the child, until the child becomes large enough to properly wear the vehicle’s seat belt. (P. 139) ●When the child becomes large enough to properly wear the vehicle’s
seat belt, follow the instructions on P. 81 regarding seat belt usage.
83
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■Replacing the belt after the pretensioner has been activated
If the vehicle is involved in multiple collisions, the pretensioner will activate for the first collision, but will not activate for the second or subsequent colli- sions.
■Seat belt extender
If your seat belts cannot be fastened securely because long enough, a personalized seat belt extender is available from your Toyota dealer free of charge.
they are not
CAUTION
Observe the following precautions to reduce the risk of injury in the event of sudden braking, sudden swerving or an accident. Failing to do so may cause death or serious injury. ■Wearing a seat belt
●Ensure that all passengers wear a seat belt. ●Always wear a seat belt properly. ●Each seat belt should be used by one person only. Do not use a seat belt
for more than one person at the same time, including children.
●Toyota recommends that children should be seated in the rear seat and
always use a seat belt and/or an appropriate child restraint system.
●Do not recline the seat any more than necessary to achieve a proper seat- ing position. The seat belt is most effective when the occupants are sitting up straight and well back in the seats.
●Do not wear the shoulder belt under your arm. ●Always wear your seat belt low and snug across your hips.
84
VENZA_OM_OM73019U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Pregnant women
Obtain medical advice and wear the seat belt in the proper way. (P. 81) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu- pants. Extend the shoulder belt com- pletely over the shoulder and position the belt across the chest. Avoid belt contact over the rounding of the abdominal area. If the seat belt is not worn properly, not only the pregnant woman, but also the fetus could suffer death or serious injury as a result of sudden braking or a colli- sion.
■People suffering illness
Obtain medical advice and wear the seat belt in the proper way. (P. 81)
■When children are in the vehicle
Do not allow children to play with the seat belt. If the belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.
■Adjustable shoulder anchor
Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injuries in the event of a sudden stop, sudden swerve or an accident. (P. 82)
85
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Seat belt pretensioners
●Do not place anything, such as a cushion, on the front passenger’s seat. Doing so will disperse the passenger’s weight, which prevents the sensor from detecting the passenger’s weight properly. As a result, the seat belt pretensioner for the front passenger’s seat may not activate in the event of a collision.
●If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer.
■Seat belt damage and wear
●Do not damage the seat belts by allowing the belt, plate or buckle to be
jammed in the door.
●Inspect the seat belt system periodically. Check for cuts, fraying, and loose parts. Do not use a damaged seat belt until it is replaced. Damaged seat belts cannot protect an occupant from death or serious injury.
●Ensure that the belt and tab are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer.
●Replace the seat assembly, including the belts, if your vehicle has been
involved in a serious accident, even if there is no obvious damage.
●Do not attempt to install, remove, modify, disassemble or dispose of a seat belt. Have any necessary repairs carried out by your Toyota dealer. Inap- propriate handling of the pretensioner may cause it to activate or operate improperly and may cause death or serious injury.
86
VENZA_OM_OM73019U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Using a seat belt extender
●Do not wear the seat belt extender, if you can fasten the seat belt without
the extender.
●Do not use the seat belt extender when installing a child restraint system, because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of a sudden stop, sudden swerve or an accident.
●The personalized extender may not be safe on another vehicle, when used by another person, or at a different seating position other than the one originally intended.
NOTICE
■When using a seat belt extender
When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.
87
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel
The steering wheel can be adjusted to a comfortable position.
STEP 1
STEP 2
Hold the steering wheel and press the lever down.
Adjust to the ideal position by moving the steering wheel horizontally and vertically.
After adjustment, pull the lever up the steering wheel.
to secure
CAUTION
■While driving
Do not adjust the steering wheel. Doing so may cause the driver to mishandle the vehicle and an accident, resulting in death or serious injury.
■After adjusting the steering wheel
Make sure that the steering wheel is securely locked. Otherwise, the steering wheel may move suddenly, possibly causing an accident and resulting in death or serious injury.
88
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Inside rear view mirror
The rear view mirror’s position can be adjusted to enable sufficient confirmation of the rear view in accordance with the driver’s seating posture.
Adjusting the height of rear view mirror
Adjust the height of the rear view mirror by moving it up and down.
89
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
Automatic anti-glare function
Responding to the level of brightness of the headlights of vehicles behind, the reflected light is automatically reduced.
Changing automatic anti-glare function mode ON/OFF
When the automatic anti-glare function is in ON mode, the indi- cator illuminates.
Vehicles with smart key system The function will set to ON mode each time the “ENGINE START STOP” switch is turned to IGNITION ON mode. Pressing the button turns the function to OFF mode. (The indicator also turns off.) Vehicles without smart key system The function will set to ON mode each time the engine switch is turned to the “ON” position. Pressing the button turns the function to OFF mode. (The indicator also turns off.)
90
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
■To prevent sensor error
To ensure correct functioning of the sen- sors, do not touch or cover the sensors.
CAUTION
■While driving
Do not adjust the position of the mirror. Doing so may lead to mishandling of the vehicle and an accident, or result- ing in death or serious injury.
91
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors
Mirror angle can be adjusted using the switch.
STEP 1
Select a mirror to adjust.
Left Right
STEP 2
Adjust the mirror.
Up Right Down Left
Folding back the mirrors (power type)
Press the switch to fold the mir- rors.
Press it again to extend them to the original position.
92
VENZA_OM_OM73019U_(U)
1-3. Adjustable components (seats, mirrors, steering wheel)
Folding back the mirrors (manual type)
Push backward to fold the mir- rors.
Blind Spot Mirrors
VENZA_OM_OM73019U_(U)
The Blind Spot Mirrors increase the view of surrounding area to assist the driver when checking surrounding area before chang- ing lanes.
Blind Spot Mirror field of view Main mirror field of view
93
1-3. Adjustable components (seats, mirrors, steering wheel)
■Mirror angle can be adjusted when
Vehicles with smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ACC” or “ON” position.
■Linked mirror function when reversing (if equipped)
When the mirror select switch is in the “L” or “R” position, the outside rear view mirrors will automatically angle downwards when the vehicle is revers- ing in order to give a better view of the ground. To disable this function, move the mirror select switch to the neutral position (between “L” and “R”).
■When the mirrors are fogged up
The outside rear view mirrors can be cleared using the mirror defoggers. Turn on the rear window defogger to turn on the outside rear view mirror defoggers. (P. 296)
■Automatic adjustment of the mirror angle (if equipped)
The mirror adjustment can be entered into memory and recalled automati- cally by the driving position memory. (P. 73)
94
VENZA_OM_OM73019U_(U)
1
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■While driving
Observe the following precautions. Failing to do so may result in losing control of the vehicle and cause an acci- dent, resulting in death or serious injury. ●Do not adjust the mirrors. ●Do not drive with the mirrors folded back. ●Before driving, be sure to extend mirrors and make an adjustment prop-
erly.
■When a mirror is moving
To avoid personal injury and mirror malfunction, be careful not to get your hand caught by the moving mirror.
■When the mirror defoggers are operating
Do not touch the rear view mirror surfaces, as they can become very hot and burn you.
NOTICE
■If ice should jam the mirror
Do not operate the control or scrape the mirror face. Use a spray de-icer to free the mirror.
95
VENZA_OM_OM73019U_(U)
1-4. Opening and closing the windows and moon roof Power windows
The power windows can be opened and closed using the following switches.
One-touch closing* Closing One-touch opening* Opening *:To stop the window partway, operate the switch in the opposite direction.
Press the switch down to lock passenger window switches.
Use this switch to prevent chil- dren from accidentally opening or closing a passenger window.
Lock switch
96
VENZA_OM_OM73019U_(U)
1
1-4. Opening and closing the windows and moon roof
■The power windows can be operated when
Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position.
■Operating the power windows after turning the engine off
Vehicles with smart key system The power windows can be operated for approximately 45 seconds even after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. They cannot, however, be operated once either front door is opened. Vehicles without smart key system The power windows can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. They cannot, however, be operated once either front door is opened.
■Jam protection function
If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.
97
VENZA_OM_OM73019U_(U)
1-4. Opening and closing the windows and moon roof
■When the power window does not close normally
If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power window switch on the relevant door. ●After stopping the vehicle, the window can be closed by holding the power window switch in the one-touch closing position while the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehi- cles with smart key system) or the engine switch is turned to the “ON” position (vehicles without smart key system).
●If the window still cannot be closed even by carrying out the operation explained above, initialize the function by performing the following proce- dure. STEP 1
Hold the power window switch in the one-touch closing position. Continue holding the switch for a further 6 seconds after the win- dow has closed. Hold the power window switch in the one-touch opening position. Continue holding the switch for a further 2 seconds after the win- dow has opened completely. Hold the power window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the window has closed.
STEP 2
STEP 3
If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after performing the above procedure correctly, have the vehicle inspected by your Toyota dealer.
■Customization
Settings (e.g. Rear window Auto Up/Down) can be changed. (Customizable features P. 519)
98
VENZA_OM_OM73019U_(U)
1
1-4. Opening and closing the windows and moon roof
CAUTION
■Closing the windows
Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their body
in a position where it could be caught when a window is being operated.
●Do not allow children to operate the power windows.
Closing a power window on someone can cause death or serious injury.
■Jam protection function
●Never try jamming any part of your body to activate the jam protection
function intentionally.
●The jam protection function may not work if something gets caught just
before the window fully closes.
99
VENZA_OM_OM73019U_(U)
1-4. Opening and closing the windows and moon roof Moon roof
Use the overhead switches to open, close, and tilt the moon roof up and down. ■ Opening and closing
Open The moon roof stops slightly before the fully open position to reduce wind noise. Move the switch backward again to fully open. Close (push and hold) The moon roof stops once. Push and hold the switch again to fully close.
Tilt up Tilt down (push and hold)
■ Tilt up and down
100
: If equipped
VENZA_OM_OM73019U_(U)
1
1-4. Opening and closing the windows and moon roof
■The moon roof can be operated when
Vehicles with smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system The engine switch is in the “ON” position.
■Operating the moon roof after turning the engine off
Vehicles with smart key system The moon roof can be operated for approximately 45 seconds even after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. It cannot, however, be operated once either front door is opened. Vehicles without smart key system The moon roof can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. It cannot, however, be operated once either front door is opened.
■To reduce moon roof wind noise
When the moon roof is opened automatically, it will stop slightly before the fully open position. Driving with the moon roof in this position can help reduce wind noise.
■Sunshade
P. 103
■Open moon roof warning buzzer Vehicles with smart key system The buzzer sounds and message is shown on the multi-information dis- play (TFT type only) when the “ENGINE START STOP” switch is turned off and the driver’s door is opened with the moon roof open. Vehicles without smart key system The buzzer sounds and message is shown on the multi-information dis- play (TFT type only) when the engine switch is turned to the “LOCK” posi- tion and the driver’s door is opened with the moon roof open.
101
VENZA_OM_OM73019U_(U)
1-4. Opening and closing the windows and moon roof
■When the moon roof does not close normally
Perform the following procedure: STEP 1
STEP 2
STEP 3
STEP 4
Stop the vehicle. Open the moon roof halfway. Press and hold the open/close switch in the close position. When the moon roof reaches the full close position, maintain the open/close switch in the close position for more than 2 seconds. It will adjust slightly and then stop. To ensure the initialization is complete, make sure opening, closing, tilting up and down functions work properly.
If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer.
CAUTION
■Opening the moon roof
Observe the following precautions. Failing to do so may cause death or serious injury. ●Do not allow any passengers to put their hands or heads outside the vehi-
cle while it is moving.
●Do not sit on top of the moon roof.
■Closing the moon roof
Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their bod- ies in a position where they could be caught when the moon roof is being operated.
●Do not allow children to operate the moon roof.
Closing the moon roof on someone can cause death or serious injury.
102
VENZA_OM_OM73019U_(U)
1
1-4. Opening and closing the windows and moon roof Sunshade
The sunshade can be opened and closed manually.
Front
Rear
Slide the sunshade.
The front sunshade will open automatically when the moon roof is opened. (P. 100)
Slide the sunshade.
: If equipped 103
VENZA_OM_OM73019U_(U)
1-5. Refueling Opening the fuel tank cap
Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle
● Vehicles with smart key system
Turn the “ENGINE START STOP” switch off and ensure that all the doors and windows are closed.
● Vehicles without smart key system
Turn the engine switch to the “LOCK” position and ensure that all the doors and windows are closed.
● Confirm the type of fuel. (P. 105)
■ Opening the fuel tank cap STEP 1
Pull the lever.
STEP 2
Turn the fuel tank cap slowly to open.
104
VENZA_OM_OM73019U_(U)
1-5. Refueling
STEP 3
Hang the fuel tank cap on the back of the fuel filler door.
Closing the fuel tank cap
When replacing the fuel tank cap, turn it until a clicking sound is heard.
After releasing your hand, the cap will turn slightly to the opposite direction.
■Fuel types
Unleaded gasoline (Octane rating 87 [Research Octane Number 91] or higher)
105
VENZA_OM_OM73019U_(U)
1-5. Refueling
CAUTION
■Refueling the vehicle
Observe the following precautions while refueling the vehicle. Failure to do so, may result in death or serious injury. ●Touch the vehicle or some other metal surface to discharge any static
electricity. Sparks resulting from discharging static electricity may cause the fuel vapors to ignite.
●Always hold the grips on the fuel tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out the filler neck and cause injury.
●Do not allow anyone that has not discharged static electricity from their
bodies to come close to an open fuel tank.
●Do not inhale vaporized fuel.
Fuel contains substances that are harmful if inhaled.
●Do not smoke while refueling the vehicle.
Doing so may cause the fuel to ignite and cause a fire.
●Do not return to the vehicle or touch any person or object that is statically
charged. This may cause static electricity to build up, resulting in a possible ignition hazard.
106
VENZA_OM_OM73019U_(U)
1
1-5. Refueling
CAUTION
■When refueling
Observe the following precautions to prevent fuel overflowing from the fuel tank: ●Securely insert the fuel nozzle into the fuel filler neck ●Stop filling the tank after the fuel nozzle automatically clicks off ●Do not top off the fuel tank
■When replacing the fuel tank cap
Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
NOTICE
■Refueling
Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle’s painted surface.
107
VENZA_OM_OM73019U_(U)
1-6. Theft deterrent system Engine immobilizer system
The vehicle’s keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehicle.
Vehicles with smart key sys- tem: The indicator light flashes after the “ENGINE START STOP” switch has been turned off to indicate that the system is operating. The indicator light stops flash- ing after the “ENGINE START STOP” switch has been turned to ACCESSORY or IGNITION ON mode to indicate that the system has been canceled. Vehicles without smart key system: The indicator light flashes after the key has been removed from the engine switch to indi- cate that the system is operat- ing. The indicator light stops flash- ing after the registered key has been inserted into the engine switch to indicate that the system has been can- celed.
108
VENZA_OM_OM73019U_(U)
1
1-6. Theft deterrent system
■System maintenance
The vehicle has a maintenance-free type engine immobilizer system.
■Conditions that may cause the system to malfunction
●If the key is in contact with a metallic object. ●If the key is in close proximity to or touching a key to the security system
(key with a built-in transponder chip) of another vehicle.
■Certifications for the engine immobilizer system
●For vehicles sold in the U.S.A.
Vehicles with smart key system FCC ID: NI4TMIMB-1
Vehicles without smart key system FCC ID: MOZRI-21BTYNOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful inter- ference, and (2) this device must accept any interference received, includ- ing interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
109
VENZA_OM_OM73019U_(U)
1-6. Theft deterrent system
●For vehicles sold in Canada
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
NOTICE
■To ensure the system operates correctly
Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.
110
VENZA_OM_OM73019U_(U)
1
1-6. Theft deterrent system Alarm
The system sounds the alarm and flashes lights when forcible entry is detected. ■ Triggering of the alarm
The alarm is triggered in the following situations when the alarm is set. ● A locked door is unlocked or opened in any way other than by using the entry function (vehicles with smart key system), the wireless remote control door lock function or the mechanical key. (The doors will lock again automatically.)
● The hood is opened. ● The battery is reconnected. ● The side windows are tapped or broken.
■ Setting the alarm system
Close the doors and hood, and lock all doors using the entry function (vehicles with smart key system) or the wire- less remote control. The sys- tem will be set automatically after 30 seconds. indicator
The light changes from being on to flashing when the system is set.
: If equipped 111
VENZA_OM_OM73019U_(U)
1-6. Theft deterrent system
■ Deactivating or stopping the alarm
Do one of the following to deactivate or stop the alarm. ● Unlock the doors using the entry function (vehicles with smart
key system) or the wireless remote control.
● Start the engine. (The alarm will be deactivated or stopped
after a few seconds.)
