2004 Toyota RAV4 Owners Manual

low tire pressure warning light may not come on even if the tire inflation pres- sure is low, or it may come on when the tire is actually normal. (cid:1) A compact spare tire, snow tires, or

inflation pressure

tire chains are used.

(cid:1) The tire inflation pressure is excessive- ly higher than specified, or tire inflation pressure suddenly drops due to burst- ing or other causes.

(cid:1) The vehicle

is driven on a slippery road surface such as rough or frozen roads.

(cid:1) The vehicle speed is less than 30 km/h (19 mph) or more than 100 km/h (62
mph), and the driving duration is less than 5 minutes.

(cid:1) The

tires differ

in

tread pattern or

manufacturer.

(cid:1) The tires are not the specified size. (cid:1) The tread wear is very different among

the installed tires.

(cid:1) Rapid

acceleration/deceleration

or

sharp turns is continued.

(cid:1) Towing a trailer.

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

LOW TIRE PRESSURE WARNING LIGHT This light comes on when the ignition key is turned to the “ON” position. It goes off after a few seconds. This indicates that the tire pressure warning system is func- tioning properly. If the low tire pressure warning light comes on or blinks while driving, do the following.

132

’04 Rav4_U (L/O 0403)

(cid:1) The loading is over the limit or imbal-

anced.

(cid:1) Initialization was not performed correct- ly after replacing or rotating tires or wheels.

(cid:1) The outside temperature is below 0(cid:2)C

(32(cid:2)F) or above 40(cid:2)C (104(cid:2)F).

CAUTION

When the tire pressure warning light comes on, observe the following in- structions: (cid:1) Adjust the tire inflation pressure to the specified level as soon as pos- sible.

(cid:1) Avoid abrupt steering wheel maneu- vering and braking. If the vehicle tires deteriorate, you could lose control of the steering wheel or the brakes, causing death or serious in- jury.

tires

Note: The tire pressure monitoring system on your vehicle will warn you when one of your tires is significantly under- inflated and when some com- binations of your tires are significant- ly under- inflated. However, there are other combinations of significantly under- inflated for which your tire pressure monitoring system may not warn you. These other combina- tions are relatively common, account- ing the instances in which vehicles have sig- nificantly under- inflated tires. For ex- ample, your system may not warn you when both tires on the same side or on the same axle of your vehicle are significantly under- inflated. It is par- ticularly important, therefore, for you to check the tire pressure in all of your regularly and maintain proper pressure.

approximately

tires

half

for

Type A

Type B

133

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

TIRE PRESSURE WARNING SYSTEM RESET SWITCH The tire pressure warning system need to be initialized in the following condi- tions: (cid:1) When the low tire pressure warning

light blinks every 0.25 seconds

(cid:1) After replacing or rotating tires or

wheels

When initializing the system, the pres- ent tire condition is stored as a stan- dard.

To initialize the system, perform the fol- lowing: 1. Park the vehicle at a safe place and apply the parking brake. Stop the en- gine.

2. Adjust the pressure of all the installed tires to the specified level. (See “Tires” on page 316 in Section 8.)

3. Turn the ignition key to “ON”.

If the low tire pressure warning light comes on, push the reset switch for a few seconds and make sure the warn- ing light goes off.

4. Push and hold the reset switch until light

tire pressure warning

low

the blinks three times.

Initialization is completed after driving at the speeds of 30 km/h (19 mph) or over for more than one hour. If the following driving conditions are satisfied, initializa- tion will be completed in about one hour. (cid:1) The vehicle speed is between 50 km/h

(31 mph) and 100 km/h (62 mph).

(cid:1) The roads are dry, smooth and straight. (cid:1) The number of passengers is 1 or 2

(including driver).

When initializing the system, make sure the low tire pressure warning light blinks three times. If the warning light does not blink three times, initializing will be failed and the tire pressure warning system will not function properly. Do not push the reset switch without ad- justing the tire inflation pressure to the specified tire pressure warning light may not come on even if the tire pressure is low, or it may come on when the tire inflation pressure is actually normal. If you push the reset switch while the vehicle is moving, initialization is not per- formed.

level. Otherwise,

low

the

134

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

Parking brake

If the low tire pressure warning light does not blink when you push and hold the reset switch, have the low pressure warn- ing system checked at your Toyota dealer. When the warning light blinks every 0.25
seconds while driving, you may be unable to reset the system. In this case, set the system again according to the above pro- cedure.

Type A

Type B

’04 Rav4_U (L/O 0403)

it while setting

When parking, firmly apply the parking brake to avoid inadvertent creeping. To set: Pull up the lever. For better hold- ing power, first depress the brake pedal and hold the parking brake. To release: Pull up the lever slightly (1), press the lock release button (2), and low- er (3). To remind you that the parking brake is set, the parking brake reminder light in the instrument panel remains on until you release the parking brake.

CAUTION

Before driving, be sure the parking brake is fully released and the park- ing brake reminder light is off.

135

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

Cruise control The cruise control allows you to cruise the vehicle at a desired speed over 40
km/h (25 mph) even with your foot off the accelerator pedal. Your cruising speed can be maintained up or down grades within the limits of engine performance, although a slight speed change may occur when driving up or down the grades. On steeper hills, a greater speed change will occur so it is better to drive without the cruise control.

CAUTION

(cid:1) To help maintain maximum control of your vehicle, do not use the cruise control when driving in heavy or varying traffic, or on slip- pery (rainy, icy or snow- covered) or winding roads.

If

(cid:1) Avoid vehicle speed increases when driving downhill. the vehicle speed is too fast in relation to the cruise control set speed, cancel the cruise control then downshift the transmission to use engine braking to slow down.

136

TURNING THE SYSTEM ON To operate the cruise control, push the “ON- OFF” switch. This turns the system on. The indicator light in the instrument panel shows that you can now set the vehicle at a desired cruising speed. Anoth- er push will turn the system completely off.

CAUTION

To avoid accidental cruise control en- gagement, keep the “ON- OFF” switch off when not using the cruise control.

SETTING AT A DESIRED SPEED On vehicles with automatic transmission, the transmission must be in “D” before you set the cruise control speed. Bring your vehicle to the desired speed, push the lever down in the “- SET” direc- tion and release it. This sets the vehicle at that speed. If the speed is not satisfac- tory, tap the lever up for a faster speed, or tap it down for a slower speed. Each tap changes the set speed by 1.6 km/h (1.0 mph). You can now take your foot off the accelerator pedal.

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

If you need acceleration—for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the set speed. When you release it, the vehicle will return to the speed set prior to the acceleration.

CAUTION

For manual transmission: While driving with the cruise control on, do not shift to neutral without depressing the clutch pedal, as this may cause engine racing or overrev- ving.

CANCELLING THE PRESET SPEED You can cancel the preset speed by: a. Pulling

lever

the

the

in

“CANCEL”

direction and releasing it.

b. Depressing the brake pedal. c. Depressing

the clutch pedal (manual

transmission).

d. Pushing “ON- OFF” switch. If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will auto- matically cancel out.

’04 Rav4_U (L/O 0403)

If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the preset speed will also automatically cancel out. If the preset speed automatically cancels out other than for the above cases, have your vehicle checked by your Toyota deal- er at the earliest opportunity. RESETTING TO A FASTER SPEED Push the lever up in the “+ RES” direction and hold it. Release the lever when the desired speed is attained. While the lever is held up, the vehicle will gradually gain speed. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “- SET” direction. RESETTING TO A SLOWER SPEED Push the lever down in the “- SET” direc- tion and hold it. Release the lever when the desired speed is attained. While the lever is held down, the vehicle speed will gradually decrease. However, a faster way to reset is to de- press the brake pedal and then push the lever down in the “- SET” direction.

If you use

On vehicles with automatic transmission, even if you turn off the overdrive switch with the cruise control on, engine braking will not be enabled because the cruise control is not cancelled. To decrease the vehicle speed, reset to a slower speed with the cruise control lever or depress the brake pedal. the brake pedal, cruise control is cancelled. RESUMING THE PRESET SPEED If the preset speed is cancelled by pulling the control the brake pedal or clutch pedal, pushing the lever up in the “+ RES” direction will re- store the speed set prior to cancellation. However, once the vehicle speed falls be- low about 40 km/h (25 mph), the preset speed will not be resumed. CRUISE CONTROL FAILURE WARNING If the instrument cluster flashes when using the cruise control, push the “ON- OFF” switch to turn the system off and then push it again to turn it on.

lever or by depressing

“CRUISE”

indicator

light

the

in

137

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

If any of the following conditions then oc- curs, there is some trouble in the cruise control system. (cid:1) The indicator light does not come on. (cid:1) The indicator light flashes again. (cid:1) The

light goes out after

indicator

it

comes on.

If this is the case, contact your Toyota dealer and have your vehicle inspected.

138

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

SECTION 1- 8

OPERATION OF INSTRUMENTS AND CONTROLS Car audio system Reference Using your audio system Audio remote controls Car audio system operating hints

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

140
141
161
162

139

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

Reference

Type 1: AM·FM radio/compact disc player (with compact disc changer controller)

Type 2: AM·FM radio/cassette player/com- pact disc player (with compact disc changer controller)

Type 3: AM·FM radio/cassette player/com- pact disc player with changer

140

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

to turn on that

Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR·VOL” to turn the audio system on and off. Push “AM”, “FM”, “FM1”, “FM2”, “TAPE” or “DISC” function without pushing “PWR·VOL”. To turn on the cas- sette or compact disc player, a cassette or compact disc must be loaded in the player. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or com- pact disc. If the another function was pre- viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “AM”, “FM”, “FM1”, “FM2”, “TAPE” or “DISC” if the system is already on but you want to switch from one function to anoth- er.

’04 Rav4_U (L/O 0403)

TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange and bass levels. In fact, different kinds of music and vocal programs usually sound better with differ- ent mixes of treble, midrange and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.

YOUR RADIO ANTENNA Your vehicle has a mast type antenna. To remove the antenna, carefully turn it counterclockwise.

NOTICE

To prevent damage to the antenna, make sure it is removed before driv- ing your Toyota through an automatic car wash.

YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should face to the right.

NOTICE

Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.

141

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

YOUR COMPACT DISC PLAYER When you insert a disc, gently push it in with the label side up. (The player will automatically eject a disc if the label side is down.) The player will play from track 1 through the end of the disc. Then it will play from track 1 again.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.

The player is intended for use with 12 cm (4.7 in.) discs only.

YOUR COMPACT DISC PLAYER WITH CHANGER (type 3) When you insert a disc, push the “LOAD” button and gently push the disc in with the label side up. (The player will auto- matically eject a disc if the label side is down.) This compact disc player can store up to six discs. The player will play from track 1 through the end of the disc. Then it will play from track 1 of the next disc.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.

The player is intended for use with 12 cm (4.7 in.) discs only.

142

NOTICE

(cid:1) Do not stack up two discs for in- sertion, or it will cause damage to the compact disc changer. Insert only one compact disc into slot at a time.

(cid:1) Never try to disassemble or oil any part of the compact disc player. Do not insert anything except a com- pact disc into the slot.

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

—Controls and features (cid:1)Type 1

Details of specific buttons, controls and features are described in the alphabetical list that follows.

143

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

(See

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The preset button number will appear on the display. To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. This radio can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM”, “FM1” or “FM2” button.)

(Eject button)

the compact disc eject button

Push eject a compact disc.

to

144

(Reverse/Fast- forward button)

time

Push and hold “ ” (preset button 6) or “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CONTROL (Tone and sound bal- ance adjustment function) Each “AUDIO push CONTROL” knob, the mode changes. To adjust the knob. BAS: Adjusts low- pitched tones. The dis- play ranges from -5 to 5. TRE: Adjusts high- pitched tones. The dis- play ranges from -5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7. BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7.

tone and balance,

turn

you

the

the

DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played. Error messages If the player malfunctions, your audio sys- tem will display one of the following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up- side down). Clean the disc and re- insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over- current. Ask your Toyota dealer to inspect.

incorrectly

inserted

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

“CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If the malfunction still exists, take your vehicle to your Toyota dealer. (cid:2) DISC (cid:1) With compact disc changer only— Use these buttons to select a disc you want to listen to. Push “(cid:2)” (preset button 3) or “(cid:1)” (preset button 4) until the number of the disc you want to listen appears on the display. FM1 FM2
Push the “FM1” or “FM2” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM sta- tions, two for each of the preset button. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume.

in random order, or

the player will perform

RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc the listen tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display and the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. With compact disc changer only— To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will ap- until you hear a beep. “ pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again.

feature, push

random

the

track

RPT (Repeat) There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again. With compact disc changer only— Repeating a disc: Push and hold “RPT” (preset button 2) ” will ap- until you hear a beep. “ pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again.

145

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold the “SCAN” button until you hear a beep. The radio will tune in the next preset station up the band, stay there for 5 seconds, and then move to the next preset station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release the “SCAN” but- ton. The radio will find the next station up the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.

listening

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release the “SCAN” but- ton. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. With compact disc changer only— Scanning the first tracks of all the discs in the magazine: Push the “SCAN” button until you hear a ·SCAN” will appear on the dis- beep. “ play and the player will scan the first track of the next disc. To stop scanning, push this button again. If the player has scanned all the discs, it will stop scan- ning.

146

the seek mode,

the radio finds and the next station up or down the

SEEK/TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release “(cid:1)” or “(cid:2)” side of the “SEEK/ TRACK” button. Do this again to find the station after that. Compact disc player Use this button to skip up or down to a different track. the “SEEK/ Push “(cid:1)” or “(cid:2)” side of TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the begin- ning of the current track, quickly push the down side of the button one time. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion.

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

to

to

title,

track

then back

TEXT This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency.

’04 Rav4_U (L/O 0403)

147

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

(cid:1)Type 2

148

’04 Rav4_U (L/O 0403)

Details of specific buttons, controls and features are described in the alphabetical list that follows.

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

(See

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The preset button number will appear on the display. To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. This radio can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM” or “FM” button.)

(Eject button) the cassette

Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc.

’04 Rav4_U (L/O 0403)

(Program)

Compact disc player

” indicates the top side, “

Push “ ” (preset button 4) to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates the bottom side). Auto- reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

feature: After

(Reverse/Fast- forward button)

Cassette player

Push “ ” (preset button 6) to fast- for- ward a cassette tape. “FF” will appear on the display. Push “ ” (preset button 5) to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast- forward- ” or “TAPE” button. To stop ing, push “ the tape while it is rewinding, push “ ” or “TAPE” button. If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast- forwards completely, the cassette will play the other side of the tape using the auto- reverse feature.

time

” (preset button 6) or Push and hold “ “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CONTROL (Tone and sound bal- ance adjustment function) Each “AUDIO push CONTROL” knob, the mode changes. To adjust the knob. BAS: Adjusts low- pitched tones. The dis- play ranges from -5 to 5. MID (on some models): Adjusts mid- pitched tones. The display ranges from -5
to 5. TRE: Adjusts high- pitched tones. The dis- play ranges from -5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7.

tone and balance,

turn

you

the

the

149

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

“CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If the malfunction still exists, take your vehicle to your Toyota dealer. (cid:2) DISC (cid:1) With compact disc changer only— Use these buttons to select the disc you want to listen to. Push “(cid:2)” (preset button 3) or “(cid:1)” (preset button 4) until the number of the disc you want to listen appears on the display. Dolby(cid:3) If you are listening to a tape that was recorded with Dolby(cid:3) B Noise Reduction, ” will push “ appear on the display. Push the button again to turn off Dolby(cid:3) B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used to re- cord the tape. : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation.

” (preset button 3). “

B NR*

FM Push the “FM” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each of the preset button. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc listen the tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display and the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again.

the player will perform

in random order, or

BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7. DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played. Error messages If the player malfunctions, your audio sys- tem will display one of the six following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up- side down). Clean the disc and re- insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over- current. Ask your Toyota dealer to inspect.

incorrectly

inserted

150

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

random

feature, push

With compact disc changer only— To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will ap- until you hear a beep. “ pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again. RPT (Repeat) Cassette player Push “RPT” (preset button 2) while the ” will appear on track is playing. “ the display. When the track ends, it will automatically rewind and replay. To turn off feature, push this button again. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.

the repeat

the

track

Compact disc player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again. With compact disc changer only— Repeating a disc: Push and hold “RPT” (preset button 2) until you hear a beep. “ ” will ap- pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again.

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold the “SCAN” button until you hear a beep. The radio will tune in the next preset station up the band, stay there for 5 seconds, and then move to the next preset station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release the “SCAN” but- ton. The radio will find the next station up the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.

151

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

listening

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release the “SCAN” but- ton. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. With compact disc changer only— Scanning the first tracks of all the discs in the magazine: Push the “SCAN” button until you hear a ·SCAN” will appear on the dis- beep. “ play and the player will scan the first track of the next disc. To stop scanning, push this button again. If the player has scanned all the discs, it will stop scan- ning.

152

the seek mode,

the radio finds and the next station up or down the

SEEK/TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release “(cid:1)” or “(cid:2)” side of the “SEEK/ TRACK” button. Do this again to find the station after that. Cassette Player Use this button to skip up or down to locate a song or recording. You can select up to nine recordings (in- cluding current one). A blank space of at least 3 seconds is considered to be a start of a recording. When the beginning of a tape is reached, the player automatically resumes play. When the end of the tape is reached, the player automatically reverses sides and resumes normal play. In addition, the feature may not work well with some spoken word, live, or classical recordings.

Compact disc player Use this button to skip up or down to a different track. the “SEEK/ Push “(cid:1)” or “(cid:2)” side of TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the begin- ning of the current track, quickly push the down side of the button one time. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push the “TAPE” button to play a cassette tape.

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

to

to

title,

track

then back

TEXT This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency.

’04 Rav4_U (L/O 0403)

153

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

(cid:1)Type 3

154

’04 Rav4_U (L/O 0403)

Details of specific buttons, controls and features are described in the alphabetical list that follows.

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

(See

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The preset button number will appear on the display. To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. This radio can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM” or “FM” button.)

(Eject button)

Cassette player This button is used to eject a cassette. Compact disc player This button is used to eject one or all compact discs. To eject the current compact disc, push and release the compact disc eject button.

’04 Rav4_U (L/O 0403)

To eject a specific disc, push “(cid:2)” (preset button 3) or “(cid:1)” (preset button 4) until the number of the disc you want to eject is displayed. Push and release the eject but- ton. To eject all discs at a time, press and hold the eject button until you hear a beep. The last compact disc played before pushing the button will be ejected first. If the ejected disc is not removed for a long time, the eject function will be cancelled.

(Program)

” indicates the top side, “

Push “ ” (preset button 4) to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates the bottom side). Auto- reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

feature: After

(Reverse/Fast- forward button)

Cassette player

” (preset button 6) to fast- for- Push “ ward a cassette tape. “FF” will appear on the display. Push “ ” (preset button 5) to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast- forward- ” or “TAPE” button. To stop ing, push “ the tape while it is rewinding, push “ ” or “TAPE” button. If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast- forwards completely, the cassette will play the other side of the tape using the auto- reverse feature. Compact disc player

” (preset button 6) or Push and hold “ “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display.

155

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

the

the

you

turn

time

tone and balance,

AUDIO CONTROL (Tone and sound bal- ance adjustment function) “AUDIO Each push CONTROL” knob, the mode changes. To adjust the knob. BAS: Adjusts low- pitched tones. The dis- play ranges from -5 to 5. MID: Adjusts mid- pitched tones. The dis- play ranges from -5 to 5. TRE: Adjusts high- pitched tones. The dis- play ranges from -5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7. BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7. DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played.

inserted

incorrectly

Error messages If the player malfunctions, your audio sys- tem will display one of the six following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up- side down). Clean the disc and re- insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over- current. Ask your Toyota dealer to inspect. “CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If the malfunction still exists, take your vehicle to your Toyota dealer. (cid:2) DISC (cid:1) Use these buttons to select a disc you want to listen to. Push “(cid:2)” (preset button 3) or “(cid:1)” (preset button 4) until the number of the disc you want to listen appears on the display.

B NR*

” (preset button 3). “

Dolby(cid:3) If you are listening to a tape that was recorded with Dolby(cid:3) B Noise Reduction, ” will push “ appear on the display. Push the button again to turn off Dolby(cid:3) B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used to re- cord the tape. : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FM Push the “FM” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each of the preset button. LOAD This button is used to load the compact discs the compact disc player. This player can store up to six discs. To load one compact disc only, quickly push and release the button, then insert a compact disc. After the disc is loaded, the shutter of the slot will close.

in

156

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

If no compact disc is inserted, the shutter will close after 15 seconds. To load multiple compact discs, push and hold the button (until you hear a beep when the audio system is on), then insert the first compact disc. After the disc is loaded, the shutter of the slot will close. After a few seconds, the shutter will auto- matically open again so the next disc can be inserted. The same process can be applied for loading the rest of the discs. If the player is full of discs, “DISC FULL” will appear on the display. If no compact disc is inserted, the shutter will close after 15 seconds. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume.

in random order, or

the player will perform

RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc the listen tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display and the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will ap- until you hear a beep. “ pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again. RDS (Radio Data System) display The radio will automatically switch to the RDS mode to receive an RDS station while tuned to FM broadcasts. “RDS” will appear on the display.

feature, push

random

the repeat

RPT (Repeat) Cassette player Push “RPT” (preset button 2) while the ” will appear on track is playing. “ the display. When the track ends, it will automatically rewind and replay. To turn off feature, push this button again. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly. Compact disc player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again.

track

the

157

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release the “SCAN” but- ton. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. Scanning the first tracks of all the discs in the magazine: Push the “SCAN” button until you hear a ·SCAN” will appear on the dis- beep. “ play and the first the player will scan track of the next disc. To stop scanning, push this button again. If the player has scanned all the discs, it will stop scan- ning.

listening

Repeating a disc: Push and hold “RPT” (preset button 2) ” will ap- until you hear a beep. “ pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again. SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold the “SCAN” button until you hear a beep. The radio will tune in the next preset station up the band, stay there for 5 seconds, and then move to the next preset station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release the “SCAN” but- ton. The radio will find the next station up the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.

158

the seek mode,

the radio finds and the next station up or down the

SEEK/TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release “(cid:1)” or “(cid:2)” side of the “SEEK/ TRACK” button. Do this again to find the station after that. Cassette Player Use this button to skip up or down to locate a song or recording. You can select up to nine recordings (in- cluding current one). A blank space of at least 3 seconds is considered to be a start of a recording. When the beginning of a tape is reached, the player automatically resumes play. When the end of the tape is reached, the player automatically reverses sides and resumes normal play. In addition, the feature may not work well with some spoken word, live, or classical recordings.

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

Compact disc player Use this button to skip up or down to a different track. the “SEEK/ Push “(cid:1)” or “(cid:2)” side of TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the begin- ning of the current track, quickly push the down side of the button one time. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push the “TAPE” button to play a cassette tape.

in RDS

to change

transmits a

is operational only

TEXT Radio This button mode. When an RDS station text message, “MSG” will appear on the dis- played. To display the text message, first push the “TEXT” button the radio station display. Then push the “TEXT” but- ton once more to display, and the mes- sage will appear on the display. If the entire the message is not displayed, ” will appear on the display. To display “ the rest of the message, push and hold the “TEXT” button until you hear a beep. After the entire message has been dis- played, the message will disappear. The message display will be canceled if any button is pushed. If no messages are “NO MESSAGE” will appear on the display, and the display returns to the previous mode. The message display will be canceled if you activate any function that affects the display.

that affects

the display

received,

to

Compact disc player This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear.

then back

track

title,

to

159

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

the

“TRAF” button,

TRAF (Traffic) This button turns the traffic announcement (TA) feature on and off. This button is operational only in FM mode. By pushing “TRAF SEEK” will flash on the display and the radio will seek a traffic program station. After the traffic announcement program is over, the display returns to the previous mode. If no traffic program station is found, “NO TRAFINFO” appears on the display, and the display returns to the previous mode and a beep sounds. To cancel the traffic announcement, push this button again. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency.

’04 Rav4_U (L/O 0403)

If no program is found, “NOTHING” will appear on the display. The previous pro- gram information will resume. When the system is left untouched for 6
seconds, type display will change to the frequency display.

the program

TYPE (Program Types) When you push “(cid:1)” or “(cid:2)” of the “TYPE” button while receiving an RDS station, the current program type will appear on the display. If the system is receiving a sta- tion that is not RDS, “NO PTY” will ap- pear. Repeat this operation within 6 seconds to display the program types in the following order: (cid:2) ROCK (cid:2) EASY LIS (Easy listening) (cid:2) CLS/JAZZ (Classical music and Jazz) (cid:2) R&B (Rhythm and Blues) (cid:2) INFORM (Information) (cid:2) RELIGION (cid:2) MISC (Miscellaneous) (cid:2) ALERT (Emergency message) To seek or scan for the same type of program, push “SEEK/TRACK” or “SCAN” button while the program type is displayed.

the

160

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

Audio remote controls (steering switches)

Some parts of the audio system can be adjusted using the switches on the steer- ing wheel. Details of the specific switches, controls, and features are described below. +” switch 1. “- 2. “(cid:2) (cid:1)” switch 3. “MODE” switch

to

+” switch

increase while

“- Push “+” side to increase the volume. The volume continues the switch is being pushed. Push “- ” side to decrease the volume. The volume continues to decrease while the switch is being pushed. “(cid:2) (cid:1)” switch Radio This switch has the following features— To select a preset station: Quickly push and release the “(cid:1)” or “(cid:2)” side of the switch. Do this again to select the next preset station. To seek a station: Push and hold the “(cid:1)” or “(cid:2)” side of the switch until you hear a beep. Do this again to find the next station. If you push the switch on either side during the seek mode, seeking will be cancelled. To step up or down the frequency, push and hold the switch even after you hear a beep. When you the switch, the radio will begin seeking up or down for a station. Do this again to find the next station.

release

from

Cassette player This switch has the following features— To skip to a different track in either direc- tion: Quickly push and release the “(cid:1)” or “(cid:2)” side of the switch. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track switch until the track you want to listen to is set. If you push the switch ten times, the skip function will turn off. (You can skip up to nine tracks at a time.) When counting the number of the tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two tracks before the song you are listening to, push the “(cid:2)” side of the switch three times. If you push the track switch further than you wanted to, push the other side of the switch. The in- creased or reduced.

track number will be

161

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

it

than

is higher

the number of

The track number you select is not valid if the tracks remaining on the current side of the cassette. (cid:2) When the tape reaches to the begin- ning, the player will automatically start playing that side.

(cid:2) After the tape reaches to the end, the reverse and

player will automatically start playing the other side.

There must be at least 3 seconds of blank space between tracks for the track switch to work correctly. In addition, the feature may not work well with some spoken, live, or classical recordings. To fast forward or reverse: Push and hold the “(cid:1)” side of the switch to fast forward a cassette tape. “FF” will appear on the display. Push and hold the “(cid:2)” side of the switch to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push the “(cid:1)” side of the switch. To stop the tape while it is rewinding, push the “(cid:2)” side of the switch. If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast forwards completely, the cassette will play the other side of the tape using the auto- reverse feature. 162

’04 Rav4_U (L/O 0403)

Compact disc player Use this switch to skip up or down to a different track in either direction. Quickly push and release the “(cid:1)” or “(cid:2)” side of the switch until the track you want to listen to is set. If you want to return to the beginning of the current track, push the “(cid:2)” side of the switch once, quickly. “MODE” switch Push “MODE” switch to select an audio mode. Each push changes the mode se- quentially if the desired mode is ready to use. To turn the audio system on, push the “MODE” switch. To turn the audio system off, push and hold the “MODE” switch until the system turns off.

Car audio system operating hints

NOTICE

To ensure correct audio system op- erations: (cid:1) Be careful not to spill beverages

over the audio system.

(cid:1) Do not put anything other than a cassette tape or Compact Disc into the slot.

(cid:1) The use of a cellular phone inside or near the vehicle may cause a noise from the speakers of the au- dio system which you are listening to. However, this does not indicate a malfunction.

RADIO RECEPTION Usually, a problem with radio reception does not mean there is a problem with your radio—it is just the normal result of conditions outside the vehicle. For example, nearby buildings and terrain can interfere with FM reception. Power lines or telephone wires can interfere with AM signals. And of course, radio signals have a limited range. The farther you are from a station, the weaker its signal will be. conditions change constantly as your vehicle moves.

In addition,

reception

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

signals are

Here are some common reception prob- lems that probably do not indicate a prob- lem with your radio: FM Fading and drifting stations—Generally, the effective range of FM is about 40 km (25
miles). Once outside this range, you may notice fading and drifting, which increase with the distance from the radio transmit- ter. They are often accompanied by distor- tion. Multi- path—FM reflective, making it possible for two signals to reach your antenna at the same time. If this happens, the signals will cancel each oth- er out, causing a momentary flutter or loss of reception. Static and fluttering—These occur when signals are blocked by buildings, trees, or other large objects. Increasing the bass level may reduce static and fluttering. the FM signal you Station swapping—If are interrupted or weak- is ened, and there is another strong station nearby on the FM band, your radio may tune in the second station until the origi- nal signal can be picked up again.

listening to

they can

AM Fading—AM broadcasts are reflected by the upper atmosphere–especially at night. These reflected signals can interfere with those received directly from the radio sta- tion, causing the radio station to sound alternately strong and weak. Station interference—When a reflected sig- nal and a signal received directly from a radio station are very nearly the same frequency, interfere with each other, making it difficult to hear the broad- cast. Static—AM is easily affected by external sources of electrical noise, such as high tension power lines, lightening, or electri- cal motors. This results in static. CARING FOR YOUR CASSETTE PLAYER AND TAPES For the best performance for your cas- sette player and tapes: Clean the tape head and other parts regu- larly. (cid:2) A dirty

tape head or tape path can decrease sound quality and tangle your cassette to clean them is by using a cleaning tape. (A wet type is recommended.)

tapes. The easiest way

Use high- quality cassettes. (cid:2) Low- quality cassette tapes can cause many problems, including poor sound, inconsistent and constant auto- reversing. They can also get stuck or tangled in the cassette player.

playing

speed,

(cid:2) Do not use a cassette if it has been damaged or tangled or if its label is peeling off.

(cid:2) Do not leave a cassette in the player if you are not listening to it, especially if it is hot outside.

(cid:2) Store cassettes in their cases and out

of direct sunlight.

(cid:2) Avoid using cassettes with a total play- ing time longer than 100 minutes (50
minutes per side). The tape used in these cassettes is thin and could get stuck or tangled in the cassette player.

163

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

CARING FOR YOUR COMPACT DISC PLAYER AND DISCS (cid:2) Your compact disc player is intended for use with 12 cm (4.7 in.) discs only. (cid:2) Extremely high temperatures can keep your compact disc player from working. On hot days, use the air conditioning to cool the vehicle interior before you listen to a disc.

(cid:2) Bumpy roads or other vibrations may

make your compact disc player skip.

(cid:2) If moisture gets into your compact disc player, you may not hear any sound even though your compact disc player appears the disc from the player and wait until it dries.

to be working. Remove

CAUTION

Compact disc players use an invisible laser beam which could cause hazard- ous if directed outside the unit. Be sure to operate the player correctly.

radiation exposure

164

Special shaped discs

(cid:2) Use only compact discs marked as shown above. The following products may not be playable on your compact disc player. Copy- protected CD CD- R (CD- Recordable) CD- RW (CD- Re- writable) CD- ROM

Low quality discs

2004 RAV4 from Mar. ’04 Prod. (OM42568U)

’04 Rav4_U (L/O 0403)

Labeled discs

NOTICE

To prevent damage to the player or changer, do not use special shaped, low quality or labeled discs such as those shown in the illustrations.

Correct

Wrong

inserting