Download PDF Manual

●When your vehicle is pointing upwards (caused by a heavy load in the lug-


gage compartment etc.)


●When the road curves or when the lanes are narrow ●When steering wheel operation or your position in the lane is unstable ●When the vehicle ahead of you decelerates suddenly


326


PRIUS PHV_OM_OM47818U_(U)


2


2-4. Using other driving systems


CAUTION


■Handling the radar sensor


Observe the following to ensure the cruise control system can function effec- tively. Otherwise, the system may not function correctly and could result in an acci- dent. ●Keep the sensor and grille cover clean at all times.


Clean the sensor and grille cover with a soft cloth so you do not mark or damage them.


●Do not subject the sensor or surrounding area to a strong impact.


If the sensor moves even slightly off position, the system may become inaccurate or malfunction. If the sensor or surrounding area is subject to a strong impact, always have the area inspected and adjusted by your Toy- ota dealer.


●Do not disassemble the sensor. ●Do not attach accessories or stickers to the sensor, grille cover or sur-


rounding area.


●Do not modify or paint the sensor and grille cover. ●Do not replace them with non-genuine parts.


327


PRIUS PHV_OM_OM47818U_(U)


2-4. Using other driving systems Driving assist systems


To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■ ABS (Anti-lock Brake System)


Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface


■ Brake assist


Generates an increased level of braking force after the brake pedal is depressed when the system detects a panic stop situation


■ VSC (Vehicle Stability Control)


Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces


■ TRAC (Traction Control)


Helps to maintain drive power and prevent the drive wheels from spin- ning when starting the vehicle or accelerating on slippery roads


■ EPS (Electric Power Steering)


Employs an electric motor to reduce the amount of effort needed to turn the steering wheel


■ Enhanced VSC (Enhanced Vehicle Stability Control)


Provides cooperative control of the ABS, TRAC, VSC and EPS. Helps to maintain directional stability when swerving on slippery road surfaces by controlling steering performance.


328


PRIUS PHV_OM_OM47818U_(U)


2-4. Using other driving systems


■ Hill-start assist control


→P. 333


■ PCS (Pre-Collision System) (if equipped)


→P. 335


When the TRAC/VSC/ABS systems are operating


The slip indicator light will flash while the TRAC/VSC/ABS sys- tems are operating.


329


PRIUS PHV_OM_OM47818U_(U)


2-4. Using other driving systems


■Sounds and vibrations caused by the ABS, brake assist, VSC and


TRAC ●A sound may be heard from the engine compartment when the hybrid system is started, just after the vehicle begins to move, if the brake pedal is depressed forcefully or repeatedly, or 1-2 minutes after the hybrid sys- tem is stopped. This sound does not indicate that a malfunction has occurred in any of these systems.


●Any of the following conditions may occur when the above systems are


operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop. • The brake pedal may pulsate slightly after the ABS is activated. • The brake pedal may move down slightly after the ABS is activated.


■EPS operation sound


When the steering wheel is operated, a motor sound (whirring sound) may be heard. This does not indicate a malfunction.


■Reduced effectiveness of the EPS system


The effectiveness of the EPS system is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time. The steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn the hybrid system off. The EPS system should return to normal within 10 minutes.


■Electric power steering system warning light


→P. 540


330


PRIUS PHV_OM_OM47818U_(U)


2


2-4. Using other driving systems


CAUTION


■The ABS does not operate effectively when


●The limits of tire gripping performance have been exceeded (such as


excessively worn tires on a snow covered road).


●The vehicle hydroplanes while driving at high speed on wet or slick road. ■Stopping distance when the ABS is operating may exceed that of nor-


mal conditions The ABS is not designed to shorten the vehicle’s stopping distance. Always maintain a safe distance from the vehicle in front of you, especially in the fol- lowing situations: ●When driving on dirt, gravel or snow-covered roads ●When driving with tire chains ●When driving over bumps in the road ●When driving over roads with potholes or uneven surfaces


■TRAC may not operate effectively when


Directional control and power may not be achievable while driving on slip- pery road surfaces, even if the TRAC system is operating. Do not drive the vehicle in conditions where stability and power may be lost.


■When the VSC is activated


The slip indicator light flashes. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes.


331


PRIUS PHV_OM_OM47818U_(U)


2-4. Using other driving systems


CAUTION


■Replacing tires


Make sure that all tires are of the specified size and of the same brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the recommended tire inflation pressure level. The ABS and VSC systems will not function correctly if different tires are installed on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.


■Handling of tires and the suspension


Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause a system to malfunction.


332


PRIUS PHV_OM_OM47818U_(U)


2


2-4. Using other driving systems Hill-start assist control


Hill-start assist control helps to prevent the vehicle from rolling backwards when starting on an incline or slippery slope.


To engage hill-start assist con- trol, further depress the brake pedal when is stopped completely.


the vehicle


A buzzer will sound once to indicate the system is acti- vated. The slip indicator will also start flashing.


■Hill-start assist control can be operated when ●The shift position is in a position other than P. ●The parking brake is not applied. ●The accelerator pedal is not depressed.


■Hill-start assist control


●While hill-start assist control is operating, the brakes remain automati- cally applied after the driver releases the brake pedal. The stop lights and the high mounted stoplight turn on.


●Hill-start assist control operates for about 2 seconds after the brake pedal


is released.


●If the slip indicator does not flash and the buzzer does not sound when the brake pedal is further depressed, slightly reduce the pressure on the brake pedal (do not allow the vehicle to roll backward) and then firmly depress it again. If the system still does not operate, check if the operat- ing conditions explained above have been met.


333


PRIUS PHV_OM_OM47818U_(U)


2-4. Using other driving systems


■Hill-start assist control buzzer


●When hill-start assist control is activated, the buzzer will sound once. ●In the following situations, hill-start assist control will be canceled and the


buzzer will sound twice. • No attempt is made to drive the vehicle within approximately 2 seconds


of releasing the brake pedal.


• Push the P position switch. • The parking brake is applied. • The brake pedal is depressed again. • The brake pedal has been depressed for more than approximately 3


minutes.


■If the slip indicator light comes on


It may indicate a malfunction in the system. Contact your Toyota dealer.


CAUTION


■Hill-start assist control


●Do not overly rely on the hill-start assist control. Hill-start assist control may not operate effectively on extremely steep inclines or roads covered in ice.


●Unlike the parking brake, hill-start assist control is not intended to hold the vehicle stationary for an extended period of time. Do not attempt to use hill-start assist control to hold the vehicle on an incline for an extended period of time, as doing so may lead to an accident.


334


PRIUS PHV_OM_OM47818U_(U)


2


2-4. Using other driving systems PCS (Pre-Collision System)∗


When the radar sensor detects possibility of a frontal collision, the pre-collision systems such as the brakes and seat belts are automat- ically engaged to lessen impact as well as vehicle damage. ■ Pre-collision seat belts (front seat belts only)


If the pre-collision sensor detects that a collision is unavoidable, the pre-collision system will retract the seat belt before the collision occurs. The same will happen if the driver makes an emergency braking or loses control of the vehicle. (→P. 158) However, when the VSC system is disabled, the system will not oper- ate in the event of skidding.


■ Pre-collision brake assist


When there is a high possibility of a frontal collision, the system applies greater braking force in relation to how strongly the brake pedal is depressed.


■ Pre-collision braking


When there is a high possibility of a frontal collision, the system warns the driver using a warning light, warning display and buzzer. If the sys- tem determines that a collision is unavoidable, the brakes are automat- ically applied to reduce the collision speed. Pre-collision braking can be disabled using the pre-collision braking off switch.


∗: If equipped 335


PRIUS PHV_OM_OM47818U_(U)


2-4. Using other driving systems


Disabling pre-collision braking


Radar sensor


Pre-collision braking enabled Pre-collision braking disabled The “PCS” warning light will turn on when pre-collision braking is disabled.


The radar sensor detects vehi- cles or other obstacles on or near the road ahead and deter- mines whether a collision is imminent based on the position, speed, and heading of the obsta- cles.


336


PRIUS PHV_OM_OM47818U_(U)


2


2-4. Using other driving systems


■The pre-collision system is operational when


●Pre-collision seat belts (type A)


• Vehicle speed is greater than about 19 mph (30 km/h). • The system detects sudden braking or skidding. • The front occupants are wearing a seat belt.


●Pre-collision seat belts (type B)


• Vehicle speed is greater than about 4 mph (5 km/h). • The speed at which your vehicle is approaching the obstacle or the vehicle running ahead of you is greater than about 19 mph (30 km/h).


• The front occupants are wearing a seat belt.


●Pre-collision brake assist:


• Vehicle speed is greater than about 19 mph (30 km/h). • The speed at which your vehicle is approaching the obstacle or the vehicle running ahead of you is greater than about 19 mph (30 km/h).


• The brake pedal is depressed.


●Pre-collision braking:


• Vehicle speed is greater than about 10 mph (15 km/h). • The speed at which your vehicle is approaching the obstacle or the vehicle running ahead of you is greater than about 10 mph (15 km/h).


• The pre-collision braking off switch is not pressed.


337


PRIUS PHV_OM_OM47818U_(U)


2-4. Using other driving systems


■Conditions that may trigger the system even if there is no possibility of


a collision ●When there is an object by the roadside at the entrance to a curve ●When passing an oncoming vehicle on a curve ●When driving over a narrow iron bridge ●When there is a metal object on the road surface ●When driving on an uneven road surface (nose up, nose down) ●When passing an oncoming vehicle on a left-turn ●When your vehicle rapidly closes on the vehicle in front ●When a grade separation/interchange, sign, billboard, or other structure


appears to be directly in the vehicle’s line of travel


●When the steep angle of the road causes a metal object located beneath


the road surface to be seen ahead of the vehicle


●When an extreme change in vehicle height occurs ●When the axis of the radar is out of adjustment ●When passing through certain toll gates ●When passing through an overpass When the system is activated in the situations described above, there is also a possibility that the seat belts will retract quickly and the brakes will be applied with a force greater than normal. When the seat belt is locked in the retracted position, stop the vehicle in a safe place, release the seat belt and refasten it.


338


PRIUS PHV_OM_OM47818U_(U)


2


2-4. Using other driving systems


■Obstacles not detected


The sensor cannot detect plastic obstacles such as traffic cones. There may also be occasions when the sensor cannot detect pedestrians, animals, bicycles, motorcycles, trees, or snowdrifts.


■Situations in which the pre-collision system does not function properly


The system may not function effectively in situations such as the following: ●On roads with sharp bends or uneven surfaces ●If a vehicle suddenly moves in front of vehicle, such as at an intersection ●If a vehicle suddenly cuts in front of vehicle, such as when overtaking ●In inclement weather such as heavy rain, fog, snow or sand storms ●When your vehicle is skidding with the VSC system off ●When an extreme change in vehicle height occurs ●When the axis of the radar is out of adjustment


■Automatic cancelation of the pre-collision system


When a malfunction occurs due to sensor contamination, etc. that results in the sensors being unable to detect obstacles, the pre-collision system will be automatically disabled. In this case, the system will not activate even if there is a collision possibility.


■When there is a malfunction in the system


Warning lights and/or warning messages will turn on or flash. (→P. 536, 548)


339


PRIUS PHV_OM_OM47818U_(U)


2-4. Using other driving systems


■Certification


For vehicles sold in the U.S.A. FCC ID: HYQDNMWR004
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Radiofrequency radiation exposure Information: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator (antenna) and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For vehicles sold in Canada Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.


340


PRIUS PHV_OM_OM47818U_(U)


2


2-4. Using other driving systems


CAUTION


■Limitations of the pre-collision system


Do not overly rely on the pre-collision system. Always drive safely, taking care to observe your surroundings and checking for any obstacles or other road hazards. Failure to do so may cause an accident resulting in death or serious injury.


■Cautions regarding the assist contents of the system


By means of alarms and brake control, the pre-collision system is intended to assist the driver in avoiding collisions through the process of LOOK- JUDGE-ACT. There are limits to the degree of assistance the system can provide, so please keep in mind the following important points. ●Assisting the driver in watching the road


The pre-collision system is only able to detect obstacles directly in front of the vehicle, and only within a limited range. It is not a mechanism that allows careless or inattentive driving, and it is not a system that can assist the driver in low-visibility conditions. It is still necessary for the driver to pay close attention to the vehicle’s surroundings. ●Assisting the driver in making correct judgement


When attempting to estimate the possibility of a collision, the only data available to the pre-collision system is that from obstacles it has detected directly in front of the vehicle. Therefore, it is absolutely necessary for the driver to remain vigilant and to determine whether or not there is a possi- bility of collision in any given situation.


●Assisting the driver in taking action


The pre-collision system’s braking assist feature is designed to help reduce the severity of a collision, and so only acts when the system has judged that a collision is unavoidable. This system by itself is not capable of automatically avoiding a collision or bringing the vehicle to a stop safely. For this reason, when encountering a dangerous situation the driver must take direct and immediate action in order to ensure the safety of all involved.


341


PRIUS PHV_OM_OM47818U_(U)


2-4. Using other driving systems


CAUTION


■When the sensor may not be correctly detecting the vehicle ahead


Apply the brakes as necessary in any of the following situations. ●When water or snow thrown up by the surrounding vehicles hinders the


functioning of the sensor


●When your vehicle is pointing upwards (caused by a heavy load in the lug-


gage compartment etc.)


●Vehicles that cut in suddenly ●Vehicles with small rear ends (trailers with no load on board etc.) ●Motorcycles traveling in the same lane


■Handling the radar sensor


Observe the following to ensure the pre-collision system can function effec- tively: ●Keep the sensor and grille cover clean at all times.


Clean the sensor and grille cover with a soft cloth so you do not mark or damage them.


●Do not subject the sensor or surrounding area to a strong impact.


If the sensor moves even slightly off position, the system may become inaccurate or malfunction. If the sensor or surrounding area is subject to a strong impact, always have the area inspected and adjusted by your Toy- ota dealer.


●Do not disassemble the sensor. ●Do not attach accessories or stickers to the sensor, grille cover or sur-


rounding area.


●Do not modify or paint the sensor and grille cover.


342


PRIUS PHV_OM_OM47818U_(U)


2-5. Driving information Cargo and luggage


Take notice of the following information about storage precau- tions, cargo capacity and load: ● Stow cargo and luggage in the luggage compartment whenever


possible.


● Be sure all items are secured in place. ● To maintain vehicle balance while driving, position luggage


evenly within the luggage compartment.


● For better fuel economy, do not carry unnecessary weight.


343


PRIUS PHV_OM_OM47818U_(U)


2-5. Driving information


Capacity and distribution


Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) — (Total weight of occupants) Steps for Determining Correct Load Limit ⎯ (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard.


(2) Determine the combined weight of the driver and passengers that


will be riding in your vehicle.


(3) Subtract the combined weight of the driver and passengers from


XXX kg or XXX lbs.


(4) The resulting figure equals the available amount of cargo and lug-


gage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400 − 750 (5 × 150) = 650 lbs.)


(5) Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.


(6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (→P. 348) Toyota does not recommend towing a trailer with your vehicle. Your vehicle is not designed for trailer towing.


344


PRIUS PHV_OM_OM47818U_(U)


Calculation formula for your vehicle


2-5. Driving information


Cargo capacity Total load capacity (vehicle capacity weight) (→P. 610)


When 2 people with the combined weight of A lb. (kg) are riding in your vehicle, which has a total load capacity (vehicle capacity weight) of B lb. (kg), the available amount of cargo and luggage load capacity will be C lb. (kg) as follows: B*2 lb. (kg) – A*1 lb. (kg) = C*3 lb. (kg) *1: A = Weight of people *2: B = Total load capacity *3: C = Available cargo and luggage load


In this condition, if 3 more passengers with the combined weight of D lb. (kg) get on, the available cargo and luggage load will be reduced E lb. (kg) as follows:


C lb. (kg) – D*4 lb. (kg) = E*5 lb. (kg) *4: D = Additional weight of people *5: E = Available cargo and luggage load As shown in the example above, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.


345


PRIUS PHV_OM_OM47818U_(U)


2-5. Driving information


CAUTION


■Things that must not be carried in the luggage compartment


The following things may cause a fire if loaded in the luggage compart- ment: ●Receptacles containing gasoline ●Aerosol cans


■Storage precautions


Observe the following precautions. Failure to do so may result in death or serious injury. ●Stow cargo and luggage in the luggage compartment whenever possi-


ble.


●Do not stack cargo and luggage in the luggage compartment higher


than the seatbacks. Such items may be thrown about and possibly injure people in the vehicle in the event of sudden braking or in an accident.


●Do not place cargo or luggage in or on the following locations as the item may get under the brake or accelerator pedal and prevent the pedals from being depressed properly, block the driver’s vision, or hit the driver or passengers, causing an accident: • At the feet of the driver • On the front passenger or rear seats (when stacking items) • On the luggage cover • On the instrument panel • On the dashboard


346


PRIUS PHV_OM_OM47818U_(U)


2-5. Driving information


CAUTION


●Secure all items in the occupant compartment, as they may shift and


injure someone in the event of an accident or sudden braking.


●When you fold down the rear seats, long items should not be place


directly behind the front seats.


●Never allow anyone to ride in the luggage compartment. It is not designed for passengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer death or serious bodily injury, in the event of sudden braking or an accident.


■Capacity and distribution


●Do not exceed the maximum axle weight rating or the total vehicle


weight rating.


●Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.


347


PRIUS PHV_OM_OM47818U_(U)


2-5. Driving information Vehicle load limits


Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. ■ Total load capacity (vehicle capacity weight): →P. 610


Total load capacity means the combined weight of occupants, cargo and luggage.


■ Seating capacity: 5 occupants (Front 2, Rear 3)


Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person.


■ Towing capacity


Toyota does not recommend towing a trailer with your vehicle.


■ Cargo capacity


Cargo capacity may increase or decrease depending on the weight and the number of occupants.


■Total load capacity and seating capacity


These details are also described on the tire and loading information label. (→P. 486)


CAUTION


■Overloading the vehicle


Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.


348


PRIUS PHV_OM_OM47818U_(U)


2


2-5. Driving information Winter driving tips


Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations


● Use fluids that are appropriate to the prevailing outside tem-


peratures. • Engine oil • Engine/power control unit coolant • Washer fluid


● Have a service technician inspect the condition of the 12-volt


battery.


● Have the vehicle fitted with four snow tires or purchase a set


of tire chains for the front tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires.


349


PRIUS PHV_OM_OM47818U_(U)


2-5. Driving information


■ Before driving the vehicle


Perform the following according to the driving conditions: ● Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. ● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.


● Check for and remove any excess ice or snow that may have accumulated on the exterior lights, vehicle’s roof, chassis, around the tires or on the brakes.


● Remove snow or mud from the bottom of your shoes before


getting in the vehicle.


■ When driving the vehicle


Accelerate the vehicle slowly, keep a safe distance between you and the vehicle ahead, and drive at a reduced speed suitable to road conditions.


■ When parking the vehicle


Park the vehicle and shift the shift position to P and block the wheel under the vehicle without setting the parking brake. The parking brake may freeze up, preventing it from being released. If necessary, block the wheels to prevent inadvertent sliding or creeping.


350


PRIUS PHV_OM_OM47818U_(U)


2


2-5. Driving information


Selecting tire chains


Use the tire chains of correct size and type. Use SAE Class “S” type radial tire chains except radial cable chains or V-bar type chains.


Regulations on the use of tire chains


Regulations regarding the use of tire chains vary depending on loca- tion and type of road. Always check local regulations before installing chains.


■Tire chain installation


Observe the following precautions when installing and removing chains: ●Install and remove tire chains in a safe location. ●Install tire chains on the front tires only. Do not install tire chains on the


rear tires.


●Install tire chains on front tires as tightly as possible. Retighten chains


after driving 1/4 - 1/2 mile (0.5 - 1.0 km).


●Install tire chains following the instructions provided with the tire chains.


351


PRIUS PHV_OM_OM47818U_(U)


2-5. Driving information


CAUTION


■Driving with snow tires


Observe the following precautions to reduce the risk of accidents. Failure to do so may result in a loss of vehicle control and cause death or serious injury. ●Use tires of the size specified. ●Maintain the recommended level of air pressure. ●Do not drive in excess of 75 mph (120 km/h), regardless of the type of


snow tires being used.


●Use snow tires on all, not just some wheels.


■Driving with tire chains


Observe the following precautions to reduce the risk of accidents. Failure to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. ●Do not drive in excess of the speed limit specified for the tire chains being


used, or 30 mph (50 km/h), whichever is lower.


●Avoid driving on bumpy road surfaces or over potholes. ●Avoid sudden acceleration, abrupt steering, sudden braking and shifting


operations that cause sudden engine braking.


●Slow down sufficiently before entering a curve to ensure that vehicle con-


trol is maintained.


352


PRIUS PHV_OM_OM47818U_(U)


2-5. Driving information


NOTICE


■Repairing or replacing snow tires


Request repairs or replacement of snow tires from Toyota dealers or legiti- mate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.


■Fitting tire chains


The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.


353


PRIUS PHV_OM_OM47818U_(U)


2-5. Driving information Trailer towing


Toyota does not recommend towing a trailer with your vehicle. Toyota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicycle, etc. Your vehicle is not designed for trailer towing or for the use of tow hitch mounted carriers.


354


PRIUS PHV_OM_OM47818U_(U)


2-5. Driving information Dinghy towing


Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.


NOTICE


■To avoid serious damage to your vehicle


Do not tow your vehicle with the four wheels on the ground.


355


PRIUS PHV_OM_OM47818U_(U)


2-5. Driving information


356


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger Air conditioning system


Airflow and outlets are automatically adjusted according to the tem- perature setting.


Outside temperature display (→P. 394) Temperature control button


Air outlet display


Fan speed control button


Windshield defogger button


Temperature setting display


Fan speed display


Off


Automatic mode


Outside air or recirculated air mode


Changes the air outlets used


Micro dust and pollen filter


Cooling and dehumidification function ON/OFF switch


358


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


Using the automatic mode


STEP 1


STEP 2


Press The air conditioning system will begin to operate. Air outlets and fan speed are automatically adjusted according to the temperature set- ting. Press “▲” to increase the temperature and “▼” to decrease the temperature on the


Adjusting the settings


■ Changing the cooling and dehumidification function


Press


The cooling and dehumidification function switches between on and off each time the button is pressed.


■ Adjusting the temperature setting


Press “▲” to increases the temperature and “▼” to decreases the temperature on the


■ Adjusting the fan speed


Press ∧ (increase) or ∨ (decrease) on The fan speed is shown on the display. (7 levels)


Press


to turn the fan off.


359


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


■ Changing the air outlets


Press


The air outlets switch each time the button is pressed.


Air flows to the upper body.


ITO31P105


Air flows to the upper body and feet.


360


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


Mainly air flows to the feet.


Air flows to the feet and the windshield defogger operates.


■ Switching between outside air and recirculated air modes


Press


The modes switches between


(recycles air inside the vehicle)


and the button is pressed.


(introduces air from outside the vehicle) modes each time


361


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


Defogging the windshield


Press


The air conditioning system con- trol operates automatically. (The gasoline engine may oper- ate during EV mode driving, depending on vehicle conditions.) Recirculated air mode will auto- matically switch to outside air mode.


Micro dust and pollen filter


Press


Outside air mode switches to recirculated air mode. Pollen is removed from the air and the air flows to the upper part of the body. Usually the system will turn off automatically approximately 3 minutes later.


To stop the operation, press


again.


362


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


Adjusting the position of and opening and closing the air outlets


■ Adjusting the air outlets Center outlets


Direct air flow to the left or right, up or down.


Right and left side outlets


Direct air flow to the left or right, up or down.


363


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


■ Opening and closing the air outlets Center outlets


Open the vent. Close the vent. Move the knob in the direction of the printed arrow until a click is heard.


Open the vent. Close the vent. Move the knob in the direction of the printed arrow until a click is heard.


Right and left side outlets


364


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


■Using the automatic mode


Fan speed is adjusted automatically in accordance with the temperature set- ting and ambient conditions, etc. As a result, the following may occur.


●Immediately after


is pressed, the fan may stop for a while until


warm or cool air is ready to flow.


●Cool air may flow to the area around the upper body when the heater is


on.


■Switching between outside air and recirculated air modes


Recirculated air mode or outside air mode may be automatically switched to in accordance with under these condition, such as temperature setting and inside temperature. Also, outside air mode may be automatically switched to when the outside temperature is low.


■When the outside temperature exceeds 75 °F (24 °C) and the air condi-


tioning system is on ●In order to reduce the air conditioning power consumption, the air condi- tioning system may switch to recirculated air mode automatically. This may also reduce fuel consumption.


●Recirculated air mode is selected as a default mode when the “POWER”


switch is turned to ON mode.


●It is possible to switch to outside air mode at any time by pressing


■Using the system in recirculated air mode


The windows will fog up more easily if the recirculated air mode is used.


365


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


■Window defogger feature


●Recirculated air mode may automatically switch to outside air mode in


situations where the windows need to be defogged.


●When the outside air temperature is low, it may take a while for the con-


densation to clear from the windshield.


●When


is turned ON, the gasoline engine may operate depending


on driving conditions. After that, even if is turned OFF, the fan does not stop and a state in which it is easy for the gasoline engine to operate continues. After defogging the windows, press as neces- sary to turn off the fan.


■When


is selected for the air outlets used


For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the temperature setting.


■Micro dust and pollen filter


●In order to prevent the windows from fogging up when the outside air is


cold, the following may occur. • Outside air mode does not switch to recirculated air mode. • The air conditioning system operates automatically. • The operation cancels after 1 minute.


●In rainy weather, the windows may fog up. Press ●Condensation may appear on the windows if this mode is used in abnor-


mally high levels of humidity.


●Pollen will be collected by the filter even when micro dust and pollen filter


mode is OFF.


■Maintenance of the air conditioning filter


The air conditioning filter must be cleaned or changed regularly to maintain air conditioning efficiency according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required. (For scheduled maintenance information, refer to the “Owner’s Manual Sup- plement/ Scheduled Maintenance Guide”.) When inspecting, cleaning and replacing the air conditioning filter, contact your Toyota dealer.


366


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


■If air flow from the vents decreases dramatically


The filter may be clogged. Contact your Toyota dealer.


■Operation of the air conditioning system in Eco drive mode


In the Eco drive mode, the air conditioning system is controlled as follows to prioritize fuel efficiency: ●Engine speed and compressor operation controlled to restrict heating/


cooling capacity


●Fan speed restricted when automatic mode is selected To improve air conditioning performance, perform the following operations: ●Adjust the fan speed ●Turn off Eco drive mode (→P. 247) ●Customize the air conditioning control of Eco drive mode. (→P. 639)


■When outside air temperature is below 32 °F (0 °C)


The cooling and dehumidification function may not operate even when


is pressed.


■Air conditioning odors


●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.


●To reduce potential odors from occurring:


• It is recommended that the air conditioning system be set to outside air


mode prior to turning the vehicle off.


• The start timing of the blower may be delayed for a short period of time immediately after the air conditioning system is started in automatic mode.


■Customization


Settings (e.g. enable/disable automatic operation of the air conditioning compressor when the “AUTO” switch ON) can be changed. (Customizable features →P. 639)


367


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


CAUTION


■To prevent the windshield from fogging up


Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.


NOTICE


■To prevent 12-volt battery discharge


Do not leave the air conditioning system on longer than necessary when the hybrid system is not operating.


368


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger Using the steering wheel climate remote control switches


Some air conditioning features can be controlled using the switches on the steering wheel.


Temperature control Outside air or recirculated air mode


Adjusting the temperature setting


Press “∧” on


to increase the temperature and “∨” to decrease


the temperature.


Changing the outside air or recirculated air modes


Press


The mode switches between outside air mode and recirculated air mode each time the switch is pressed.


369


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


■When operating the steering switches (vehicles with touch tracer dis-


play) ●The steering switches operation status is displayed on the instrument


cluster for confirmation purposes. (→P. 258)


●Settings are shown on the multi-infor- mation display when the steering switch is operated.


CAUTION


■To reduce the risk of an accident


Exercise care when operating the air conditioning switches on the steering wheel.


370


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger Remote Air Conditioning System


The Remote Air Conditioning System uses electrical energy stored in the hybrid battery (traction battery) and allows the air conditioning to be operated by remote control. If the Remote Air Conditioning System is used while the charging cable is connected to the vehicle, the reduction of charge in the hybrid battery (traction battery) will be suppressed to allow you to use electricity from an external power source.


Charging will be conducted automatically after the Remote Air Condi- tioning System is stopped.


■ Before leaving the vehicle


Check the temperature setting of the air conditioning system. The Remote Air Conditioning System will operate in accordance with the temperature settings of the air conditioning system. ■ Activating the Remote Air Conditioning System


Press and hold the to operate the Remote Air Condi- tioning System.


The system will shut off if a door is opened. The system can be stopped by pressing the


twice.


371


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


■Operating conditions


The system will only operate if all of the following conditions are met: ●The shift position is in P. ●The “POWER” switch is OFF. ●All doors are closed. ●The hood is closed. ●The brake pedal is not being depressed.


■When leaving the vehicle


●Check that the headlights are switched to either off or “AUTO”. ●Check that the wiper switch is turned off. ●Check that all windows are closed.


■Remote Air Conditioning System automatic shut-off


The system will automatically shut off under the following conditions: ●About 10 minutes have passed since operation began ●Any one of the operating conditions is not met ●There is only a slight difference between the air conditioning set temper-


ature and the inside temperature.


The system may also shut off if the charge level of the hybrid battery (trac- tion battery) drops to low. (→P. 60)


■Conditions affecting operation


The system may not start in the following situations: ●The charge level of the hybrid battery (traction battery) is low (→P. 60) ●The air conditioning temperature is set at a high level or outside tempera-


ture is low


●When the hybrid system is cool (for example, after being left for a long


time in low temperatures)


372


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


■Security feature


Any unlocked doors will be automatically locked when the system is operat- ing. The buzzer will beep and the emergency flashers flash when the doors have been locked or the system has been turned off. (The doors locked: Once; The system turned off: Twice)


■Conditions affecting operation


→P. 119


■When using the Remote Air Conditioning System


A charging message will be displayed on the multi-information display. Dif- ferent messages will be displayed depending on when the Remote Air Con- ditioning System was started (after charging or during charging). (→P. 562)


■While the Remote Air Conditioning System is operating


●Depending on the operating condition of the Remote Air Conditioning System, the electric fan may spin and an operating noise may be heard. However, this does not indicate a malfunction.


●The Remote Air Conditioning System may stop operating temporarily if other features that use electricity (for example, the seat heater, lights, windshield wipers) are in operation or if the charge level of the 12-volt battery becomes low.


■Electronic key battery depletion


→P. 123


■When the electronic key battery is fully depleted


→P. 123


■Customization


Setting (e.g. Operation using the be changed. (Customizable features →P. 645)


on the wireless remote control) can


373


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger


CAUTION


■Precautions for the Remote Air Conditioning System


●Do not use the system if people are in the vehicle.


• Even when the system is in use, the internal temperature may still reach a high level due to features such as the automatic shut-off. Chil- dren and pets left inside the vehicle may suffer heatstroke or dehydra- tion, or could result in death or serious injury.


• The wipers can be operated during system operation. Children or pets left inside the vehicle may mistakenly operate these and cause an acci- dent.


●Depending on the surrounding environment, signals from the wireless switch may transmit further than expected. Pay appropriate attention to the vehicle’s surroundings and use the switch only when necessary.


●Turn the wipers off. If the Remote Air Conditioning System operates while the wiper switch is in the on position, the wipers may operate and objects may get caught in the wiper blades.


●Do not operate the


if the hood is open. The air conditioning may operate unintentionally and objects may be drawn into the electrical cool- ing fan.


NOTICE


■To prevent the hybrid battery (traction battery) from being discharged


through incorrect operation


Use the


only when necessary.


374


PRIUS PHV_OM_OM47818U_(U)


3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers switch


Defoggers are used to defog the rear window, and to remove rain- drops, dew and frost from the outside rear view mirrors (if equipped).


Turns the rear window and outside rear view mirror defog- gers on/off


The defoggers will automati- cally turn off after approxi- mately 15 minutes.


■Operating conditions


The “POWER” switch is in ON mode.


■The outside rear view mirror defoggers (if equipped)


Turning the rear window defogger on will turn the outside rear view mirror defoggers on.


CAUTION


■When the outside rear view mirror defoggers are on (if equipped)


Do not touch the outside surface of the rear view mirrors, as they can become very hot and burn you.


NOTICE


■To prevent 12-volt battery discharge


Do not leave the rear window defogger on longer than necessary when the hybrid system is off.


375


PRIUS PHV_OM_OM47818U_(U)


3-2. Using the audio system Audio system types


Vehicles with Display Audio system Type A


Type B


Refer to the “Display Audio System Owner’s Manual”.


376


PRIUS PHV_OM_OM47818U_(U)


3-2. Using the audio system


Vehicles with a navigation system


Canada


Refer to the “Navigation System Owner’s Manual”.


Steering wheel audio switches


Some audio features can be controlled using the switches on the steering wheel. For details, refer to the “Display Audio System Owner’s Manual” or “Navigation System Owner’s Manual”. Operation may differ and usage may not be possible with audio/navi- gation systems that are not compatible with the steering switches in this vehicle.


377


PRIUS PHV_OM_OM47818U_(U)


3-2. Using the audio system


■About Bluetooth® (vehicles with Display Audio system)


Bluetooth is a registered trade mark of Bluetooth SIG. Inc. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Panasonic Corpo- ration is under license. Other trademarks and trade names are those of their respective owners.


CAUTION


■Certification for the Display Audio system


FCC ID: ACJ932CQ-US70G0
●Part 15 of the FCC Rules


FCC Warning: Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.


●Laser products


• Do not take this unit apart or attempt to make any changes by yourself. This is an intricate unit that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet. Therefore, never try to disas- semble the player or alter any of its parts since you may be exposed to laser rays and dangerous voltages.


• This product utilizes a laser.


Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation expo- sure.


378


PRIUS PHV_OM_OM47818U_(U)


3-2. Using the audio system


CAUTION


Properly shielded a grounded cables and connectors must be used for con- nection to host computer and / or peripherals in order to meet FCC emission limits. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undes- ired operation of this device. Le présent appareil est conforme aux la partie 15 des règles de la FCC et CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Expo- sure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio fre- quency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radia- tor at least 20 cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles). Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directices d’exposition dans le Sup- plément C à OET65 et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant, cet équipement doit être installé et utilisé en gardant une dis- tance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chivilles).


379


PRIUS PHV_OM_OM47818U_(U)


3-2. Using the audio system


CAUTION


Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that neces- sary for successful communication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utili- sateurs, il faut choisir le type d’antenne et son gain de sorte que la puis- sance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.


380


PRIUS PHV_OM_OM47818U_(U)


3-2. Using the audio system Using the AUX port/USB port


This port can be used to connect a portable audio device and listen to it through the vehicle’s speakers.


STEP 1


Open the console box lid. (→P. 387)


STEP 2


Connect the portable audio device.


■Operating portable audio devices connected to the audio system


The volume can be adjusted using the vehicle’s audio controls. All other adjustments must be made on the portable audio device itself.


■When using a portable audio device connected to the power outlet


Noise may occur during playback. Use the power source of the portable audio device.


381


PRIUS PHV_OM_OM47818U_(U)


3-3. Using the interior lights Interior lights list


Rear interior light (→P. 384) Front interior/personal lights (→P. 383) Shift lever lighting “POWER” switch lighting Foot lights (if equipped) Front door courtesy lights


382


PRIUS PHV_OM_OM47818U_(U)


Front interior lights


3-3. Using the interior lights


Front interior lights and personal lights


Turns the lights off Turns the door position on Turns the lights on


Personal lights


Type A


Turns the lights on/off


Type B


Turns the lights on/off


383


PRIUS PHV_OM_OM47818U_(U)


3-3. Using the interior lights


Rear interior light


Rear interior light


The light will turn on/off in con- junction with the front interior lights Turns the light on


ITI34P133a


■Illuminated entry system


The lights automatically turn on/off according to “POWER” switch mode, the presence of the electronic key, whether the doors are locked/unlocked, and whether the doors are opened/closed. ■To prevent 12-volt battery discharge


If the interior lights remain on when the door is not fully closed and the inte- rior light switch (door position on/off) is on, the lights will go off automatically after 20 minutes. ■Customization


Setting (e.g. The time elapsed before lights turn off) can be changed. (Customizable features →P. 643)


NOTICE

Loading...
x