CAUTION
the
injured by
D The SRS airbag system is designed only as a supplement to the prima- ry protection of the driver and pas- senger seat belt systems. The driv- er and passenger can be killed or seriously inflating airbags if they do not wear the available seat belts properly. During sudden braking just before a colli- sion, an unrestrained driver or pas- senger can move forward into direct contact with or close proximity to the airbag which may then deploy during the collision. To ensure max- imum protection in an accident, the driver and passenger in the vehicle must wear their seat belts properly. Wearing a seat belt properly during an accident reduces the chances of death or serious injury or being thrown out of the vehicle. For in- structions and precautions concern- ing the seat belt system, see “Seat belts—” on page 31.
38
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
Indicator light
SB13106a
airbag
system
passenger
The is equipped with a manual on−off switch and indicator light. Turning the passen- ger airbag manual on−off switch clock- wise to the “ON” position makes the passenger airbag system operational. Turning the passenger airbag manual on−off switch counterclockwise to the “OFF” position disables the passenger airbag system. The indicator light on the passenger airbag manual on−off switch will come on when the passen- ger airbag system has been disabled. See “Passenger airbag manual on−off switch” on page 45 in this Section for detail.
CAUTION
D Make sure that the indicator light is
off.
D Do not turn off the passenger air- bag manual on−off switch except when a member of a passenger risk group identified in TABLE 1 is oc- cupying the passenger seating posi- tion.
D When the passenger airbag manual on−off switch is turned off, the pas- senger airbag will not inflate in a collision and turning off the pas- senger airbag can reduce the occu- pant protection which your vehicle safety systems can provide to you in certain accidents and increase the likelihood of serious personal injuries.
2005 MR2 from Aug. ’04Prod. (OM17527U)
39
04 09.01
TABLE 1: A PASSENGER RISK GROUP
Infant. An infant (less than 1 year old) who must ride in the front seat because: D Vehicle has no rear seat; D Vehicle has a rear seat too small to accommodate a rear−facing infant seat; or D The infant has a medical condition which, according to the infant’s physician, makes it necessary for the infant to ride in the front seat so that the driver can constantly monitor the child’s condition.
Child age 1 to 12. A child age 1 to 12 must ride in the front seat because: D Vehicle has no rear seat: D Although children ages 1 to 12 ride in the rear seat(s) whenever possible, children ages 1 to 12 sometimes must ride in the front because no space is available in the rear seat(s) of vehicle; or
D The child has a medical condition which, according to the child’s physician, makes it necessary for the child to ride in the front seat so that the driver can constantly monitor the child’s condition.
Medical condition. A passenger has a medical condition which according to his or her physician: D Causes the passenger airbag to pose a special risk for the passenger: and D Makes the potential harm from the passenger airbag in a crash greater than the potential harm from turning off the airbag and allowing the passenger, even if belted, to hit the dashboard, or windshield in a crash.
For more detailed information concerning about the passenger risk group, please contact NHTSA at 1−800−424−9393.
this
(usually
The SRS airbags are designed to deploy in severe frontal) collisions where the magnitude and duration of the forward deceleration of the vehicle exceeds the designed threshold level. The SRS airbags will deploy if the severi- ty of the impact is above the designed threshold level, comparable to an approxi- mate 25 km/h (15 mph) collision when the vehicle has the impact straight into a fixed barrier that does not move or deform. However, threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if the vehicle is involved in an underride collision in which the front of the vehicle “underrides”, or goes under, the bed of a truck, etc.). It in some collisions where the forward deceleration of the ve- hicle is very close to the designed thresh- old level, the SRS airbags and the seat belt pretensioners may not activate togeth- er. Always wear your seat belts properly.
(e.g. a collision
is possible
that
40
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
Collision from the rear
SC13014a
Hitting a curb, edge of pavement or hard surface
SB13077
Falling into or jumping over a deep hole
Collision from the side
Vehicle rollover
Landing hard or vehicle falling
The SRS airbags are not generally de- signed to inflate if the vehicle is in- volved in a side or rear collision, if it rolls over, or if it is involved in a low− speed frontal collision. But, whenever a collision of any type causes sufficient forward deceleration of the vehicle, de- ployment of the SRS airbags may oc- cur.
The SRS airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.
SB13094a
The SRS airbag system consists mainly of the following components, and their loca- tions are shown in the illustration. 1. Front airbag sensor 2. SRS warning light 3. Airbag module for passenger
(airbag and inflator)
4. Airbag sensor assembly 5. Airbag module for driver
(airbag and inflator)
The airbag sensor assembly consists of a safing sensor and airbag sensor.
2005 MR2 from Aug. ’04Prod. (OM17527U)
41
04 09.01
The airbag sensors constantly monitor the forward deceleration of the vehicle. If an impact results in a forward deceleration beyond the designed threshold level, the system triggers the airbag inflators. At this time a chemical reaction in the inflators very quickly fills the airbags with non−tox- ic gas to help restrain the forward motion of the occupants. The airbags then quickly deflate, so that there is no obstruction of the driver’s vision should it be necessary to continue driving. When the airbags inflate, they produce a loud noise and release some smoke and residue along with non−toxic gas. This does not indicate a fire. This smoke may remain inside the vehicle for some time, and may cause some minor irritation to the eyes, skin or breathing. Be sure to wash off any residue as soon as possible to prevent any potential skin irritation with soap and water. If you can safely exit from the vehicle, you should do so imme- diately.
CAUTION
The driver or passenger who is too close to the steering wheel or dash- board during airbag deployment can be killed or seriously injured. Toyota strongly recommends that: D The driver sit as far back as pos- sible from the steering wheel while still maintaining control of the ve- hicle.
D The passenger sit as far back as
possible from the dashboard.
D All vehicle occupants be properly restrained using the available seat belts.
For instructions and precautions con- cerning the seating position, see “—Seat precautions” on page 28.
injuries, especially
Deployment of the airbags happens in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, primarily to the head and chest, it may also cause other, less severe injuries to the face, chest, arms and hands. These are usually in the nature of minor burns or abrasions and swelling, but the force of a deploying airbag can cause more seri- ous if an occupant’s hands, arms, chest or head is in close proximity to the airbag module at the time of deployment. This is why it is important for to: avoid placing any object or part of the body between the occupant and the airbag module; sit straight and well back into the seat; wear the available seat belt properly; and sit as far as possible from the airbag module, while still maintaining control of the ve- hicle. Parts of the airbag module (steering wheel hub, airbag cover and inflator) may be hot for several minutes after deployment, so do not inflate only once. The windshield may be damaged by absorbing some of the force of the inflat- ing airbag.
touch! The airbags
the occupant
42
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
SB13053
SB13054
SB13055
D Do not sit on the edge of the seat or lean against the dashboard when the vehicle is in use, since the pas- senger airbag could inflate with considerable speed and force. Any- one who is up against, or very close to, an airbag when it inflates, can be killed or seriously injured. Sit up straight and well back in the seat, and always use your seat belt properly.
D Do not allow a child to stand up or kneel on the passenger seat, since the passenger airbag could inflate with considerable speed and force. Otherwise, the child may be killed or seriously injured.
D Do not hold a child on your lap or in your arms. Use a child restraint system in the seat. For instructions concerning installation of a child restraint system, see “Child restraint—” on page 46.
the
restrict
D Do not put anything or any part of your body on or in front of the dashboard or steering wheel pad that houses the airbag system. They might inflation or cause death or serious injury as they are projected rearward by the force of deploying airbags. Likewise, the driver and passenger should not hold objects in their arms or on their knees.
2005 MR2 from Aug. ’04Prod. (OM17527U)
43
04 09.01
D Do not modify or remove any wir- ing. Do not modify, remove, strike or open any components such as the steering wheel pad, steering wheel, column cover, dashboard near the passenger airbag, passen- ger airbag cover, passenger airbag or airbag sensor assembly. Doing so may prevent the airbag system from activating correctly, cause sud- den activation of the system or dis- able the system, which could result in death or serious injury.
Failure to follow these instructions can result in death or serious injury. Consult your Toyota dealer about any repair and modification.
NOTICE
consulting
Do not perform any of the following changes without your Toyota dealer. Such changes can in- terfere with proper operation of the SRS airbag system in some cases. z Installation of electronic devices such as a mobile two−way radio, cassette tape player or compact disc player
z Modification of the suspension sys-
tem
z Modification of the front end struc-
ture
z Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end
z Repairs made on or near the front fenders, front end structure, con- sole, steering wheel or dashboard near the pas- senger airbag
steering
column,
SB13102a
light system monitors
This indicator comes on when the igni- tion key is turned to the “ON” position. It goes off after about 6 seconds. This means the SRS airbags are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, seat belt pretensioner assemblies, inflators, warning light, interconnecting wir- ing and power sources. (For details, see “Service reminder indicators and warning buzzers” on page 77.) If any of the following conditions occurs, this indicates a malfunction of the airbags or seat belt pretensioners. Contact your Toyota dealer as soon as possible.
44
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
D The light does not come on when the
ignition key is turned to the “ON” posi-
tion or remains on for more than 6
seconds or flashes.
D The light comes on or flashes while
driving.
Passenger airbag manual on−off switch
Indicator light
SB13067a
SB13106a
In the following cases, contact your Toyota dealer as soon as possible: D The SRS airbags have been inflated. D The front of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS airbags to inflate.
D The pad section of the steering wheel or passenger airbag cover (shaded in the illustration) is scratched, cracked, or otherwise damaged.
NOTICE
Do not disconnect the battery cables before contacting your Toyota dealer.
This on−off switch is designed to dis- able the passenger airbag in order to allow usage, if necessary, of a member of a passenger risk group identified in TABLE 1 (on page 40) is occupying the passenger seating position (For details, see “SRS driver airbag and passenger airbag” on page 37 in this Section.) Operate on−off switch as follows: Insert key into the keyhole and turn it in the glove box. To turn passenger airbag on: Turn the key clockwise to the “ON” position. To turn passenger airbag off: Turn the key counterclockwise to the “OFF” position.
2005 MR2 from Aug. ’04Prod. (OM17527U)
45
04 09.01
The indicator comes on when the passen- ger airbag system is off. To check the airbag cut−off system status, turn the ignition switch to the “ON” posi- tion. The “AIRBAG” warning light and the “OFF” for approximately 4 seconds. the airbag switch is turned off, the “OFF” indicator will continue to illuminate, and if the air- bag switch is turned on, the “OFF” indica- tor will not illuminate.
light should go on
indicator
If
CAUTION
D Make sure that the indicator light is
off.
D Do not turn off the passenger air- bag manual on−off switch except when a member of a passenger risk group (on page 40) is occupying the passen- ger seating position.
in TABLE 1
identified
D When the passenger airbag manual on−off switch is turned off, the pas- senger airbag will not inflate in a collision and turning off the pas- senger airbag can reduce the occu- pant protection which your vehicle safety systems can provide to you in certain accidents and increase the likelihood of serious personal injuries.
For details, see “SRS driver airbag and passenger airbag” on page 37 in this Section.
Child restraint— —Child restraint precautions Toyota strongly urges the use of ap- propriate child restraint systems for children. The laws of all 50 states in the U.S.A. now require the use of a child restraint system. Your vehicle conforms to SAEJ1819.
CAUTION
D For effective protection in automo- bile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an acci- dent, the child can be crushed against the windshield, or between you and the vehicle’s interior.
D Toyota strongly urges use of a proper child restraint system that conforms to the size of the child.
46
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
D Never install infant or child age 1
to 12 in a passenger risk group on
the passenger seat with the passen-
ger airbag manual on−off switch in
the “ON” position. In the event of
an accident, the force of the rapid
inflation of
the passenger airbag
can cause death or serious injury
to the child.
If you must install infant or child
age 1 to 12
in a passenger risk
group on the passenger seat, make
sure the passenger airbag manual
on−off switch
the “OFF”
position and that the indicator light
is on. (For details, see “SRS driver
airbag and passenger airbag” on
page 37 in this Section.
in
is
installing a child
D Do not use the seat belt extender when restraint system on the passenger seat. If installing a child restraint system with the seat belt extender con- nected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passenger in the event of collision.
D Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly se- cured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sud- den stop or accident.
—Child restraint system A child restraint system for a small child or baby must be properly re- strained on the seat with the lap por- tion of the lap/shoulder belt. You must carefully consult the manufacturer’s in- structions which accompany the child restraint system. To provide proper restraint, use a child restraint system following the manufactur- er’s instructions about the appropriate age and size of the child for the child restraint system. Install the child restraint system correctly following the instructions provided by its manufacturer. General directions are also provided under the following illustrations. When not using the child restraint system, keep it secured with the seat belt or place it in somewhere other than the passenger compartment. This will prevent it from in- juring passenger in the event of a sudden stop or accident.
2005 MR2 from Aug. ’04Prod. (OM17527U)
47
04 09.01
to
following 3
types according
—Types of child restraint system Child restraint systems are divided into the the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer. Your vehicle has anchor brackets for se- curing the top strap of a child restraint system. For instructions about how to use the an- chor bracket, see “—Using a top strap” on page 58. The approved used. See restraint lower anchorages” on page 59.
lower anchorages for your vehicle may also be child
“—Installation with
restraint
child
SB13056
SB13048a
(A) Infant seat
(C) Booster seat
SB13080a
(B) Convertible seat
48
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
—Installation with seat belt
SB13081
SB13101
SB13107a
(A) INFANT SEAT INSTALLATION An infant seat must be used in rear− facing position only.
CAUTION
Never install a rear−facing child re- straint system on the passenger seat with the passenger airbag manual on− off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the passenger airbag can cause death or serious in- jury to the child.
When you put a rear−facing child re- straint system which belongs to a pas- senger risk group on the passenger seat, turn the passenger airbag manual on−off switch counterclockwise to the “OFF” position. (For details, see “SRS driver airbag and passenger airbag” on page 37 in this Section.) The indicator comes on when the system is off.
2005 MR2 from Aug. ’04Prod. (OM17527U)
49
04 09.01
CAUTION
If you must install a rear−facing child restraint system on the passenger seat, make sure the passenger airbag manual on−off switch is in the “OFF” position and that the indicator light is on.
SB13057
1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.
CAUTION
D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.
D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.
D If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.
install
50
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
SB13058
SB13059
SB13060
2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.
the
To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.
3. While pressing the infant seat
firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.
CAUTION
Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.
2005 MR2 from Aug. ’04Prod. (OM17527U)
51
04 09.01
SB13095
SB13062
SB13101
4. To remove the infant seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.
freely again and be ready
(B) CONVERTIBLE SEAT INSTALLATION A convertible seat must be used in for- ward−facing or rear−facing position de- pending on the age and size of the child. When the manufacturer’s instruction about the ap- plicable age and size of the child as well as directions the child restraint system.
installing,
installing
follow
for
CAUTION
Rear−facing child restraint system: Never install a rear−facing child re- straint system on the passenger seat with the passenger airbag manual on− off switch in the “ON” position. In the event of an accident, the force of the rapid inflation of the passenger airbag can cause death or serious in- jury to the child.
52
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
SB13107a
CAUTION
D If you must
install a rear−facing child restraint system on the pas- senger seat, make sure the passen- ger airbag manual on−off switch is in the “OFF” position and that the indicator light is on.
SB13083a
When you put a forward−facing or a rear−facing child restraint system which belongs to a passenger risk group on the passenger seat, turn the passenger airbag manual on−off switch counter- clockwise to the “OFF” position. (For details, see “SRS driver airbag and pas- senger airbag” on page 37 in this Sec- tion.) The indicator comes on when the system is off.
forward−facing child
D Forward−facing child restraint sys- tem: A re- straint system which belongs to a passenger risk group should never be installed on the passenger seat with the passenger airbag manual on−off switch in the “ON” position, because the passenger airbag could inflate with considerable speed and force. Otherwise the child may be killed or seriously in for- ward seating position. (For details, see “SRS driver airbag and passen- ger airbag” on page 37 in this Sec- tion.)
injured
1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.
provided insert the
by tab
2005 MR2 from Aug. ’04Prod. (OM17527U)
53
04 09.01
CAUTION
D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt is not twisted.
D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.
D If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.
install
SB13084a
SB13085a
2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted slightly, it cannot be ex- tended. To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.
3. While pressing
the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.
54
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
SB13086a
SB13096
SB13108
CAUTION
Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.
4. To remove the convertible seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.
freely again and be ready
(C) BOOSTER SEAT INSTALLATION A booster seat must be used in for- ward−facing position only.
2005 MR2 from Aug. ’04Prod. (OM17527U)
55
04 09.01
CAUTION
child
forward−facing
airbag manual
the passenger seat with
restraint system which belongs to a passenger risk group should never be installed the on passenger on−off switch in the “ON” position, because the passenger airbag could inflate with considerable speed and force. Otherwise the child may be killed or seriously injured in forward seating position. (For details, see “SRS driver airbag and passenger airbag” on page 37 in this Section.)
SB13107a
SB13064
When you put a forward−facing child restraint system which belongs to pas- senger risk group on the passenger seat, turn the passenger airbag manual on−off switch counterclockwise to the “OFF” position. (For details, see “SRS driver airbag and passenger airbag” on page 37 in this Section.) The indicator comes on when the system is off.
1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and across the child following the instructions provided by its manufacturer and insert the tab into the buckle, taking care not to twist the belt.
Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on the child’s hips. See “Seat belts—” on page 31 in this Section for details.
56
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
CAUTION
D Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Otherwise, the child may be killed or seriously injured in case of sud- den braking or a collision.
D If the seat belt does not function normally, it cannot protect your child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.
install
SB13097
could
D Both high−positioned lap belts and cause loose−fitting belts death or serious to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on a child’s hips as possible.
injuries due
D For child’s safety, do not place the
shoulder belt under child’s arm.
D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.
D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.
2. To remove the child restraint system, the buckle release button and
press allow the belt to retract.
2005 MR2 from Aug. ’04Prod. (OM17527U)
57
04 09.01
—Using a top strap
SB13110
SB13111
SB13112a
Follow the procedure below for a child restraint system that requires the use of a top strap.
Use the anchor bracket on the luggage trim to attach the top strap. Anchor brackets are installed for a pas- senger seating position. This symbol indicates the location of the anchor bracket.
TO USE THE ANCHOR BRACKET 1. Lightly push up the anchor bracket it forward to re-
cover, then pull move.
58
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
SB13113
2. Fix the child restraint system with
the seat belt. Latch bracket and tighten the top strap.
the hook onto
the anchor
instructions
For child restraint system, see “—Types of child restraint system” on page 48.
install
the
to
CAUTION
D Do not slide the seat after securing
the child restraint system.
D Make sure the top strap is securely latched, and check that the child restraint system is secure by push- ing and pulling it in different direc- tions.
Follow all the installation instructions provided by its manufacturer.
Store a removed cover in a safe place such as the glove box. Be sure to replace a cover when the an- chor bracket is not in use.
—Installation with child restraint lower anchorages
SB13116
interfaced with
The lower anchorages for the child re- straint system the FMVSS225 specification are installed in the passenger seat. The anchorages are installed in the gap between the seat cushion and seatback of passenger seat. Child restraint system interfaced with the FMVSS213 specification can be fixed with these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.
2005 MR2 from Aug. ’04Prod. (OM17527U)
59
04 09.01
9th lock position
1st lock position
SB13118b
SB13117a
Rearmost position
More than 3 notches
SYSTEM
RESTRAINT
CHILD INSTALLATION 1. Fold down the seatback and slide the seat backward into the rearmost position. Then slide it forward by more than 3 notches.
2. Raise the seatback back to the 1st lock position (most upright position) until it locks into place. Adjust the seatback to the 9th lock position. Make sure the seatback is locked se- curely.
SB13115a
60
Type A
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
3. Type A—Latch the hooks of
lower straps onto the lower anchorages lo- cated between the seat cushion and seatback, and lower straps. Type B—Latch the buckles onto the lower anchorages located between the seat cushion and seatback.
tighten
the
it should be anchored. (For
If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 58.) For installation details, refer to the instruc- tion manual equipped with each product.
SB13114a
CAUTION
D When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.
D Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.
it
D After securing
system, never slide change the seatback angle.
the child restraint the seat or
Type B
2005 MR2 from Aug. ’04Prod. (OM17527U)
61
04 09.01
62
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
SECTION 1− 4
OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Tilt steering wheel Outside rear view mirrors Anti−glare inside rear view mirror
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
64
64
66
2005 MR2 from Aug. ’04Prod. (OM17527U)
63
04 09.01
Tilt steering wheel
Outside rear view mirrors—
CAUTION
D Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- dle the vehicle and an accident may occur resulting in death or serious injuries.
D After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.
SB13049
To change the steering wheel angle, hold the steering wheel, push the lock release lever, tilt the steering wheel to the desired angle and return the lever to its original position.
SB13050
Adjust the mirror so that you can see the side of your vehicle in the mirror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side because it is a convex mirror. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.
64
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
—Power rear view mirror control
CAUTION
Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.
SB13099a
NOTICE
If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror.
To adjust a mirror, use the switches. 1. Master switch—To select the mirror to
be adjusted Push (right).
the switch to “L” (left) or “R”
2. Control switch—To move the mirror
Push the switch in the desired direc- tion.
Mirrors can be adjusted when the key is in the “ACC” or “ON” position.
2005 MR2 from Aug. ’04Prod. (OM17527U)
65
04 09.01
—Folding rear view mirrors
Anti−glare inside rear view mirror
SB13051
SB13088
CAUTION
Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in personal death or injuries.
The rear view mirrors can be folded backward for parking in compact areas. To fold the rear view mirror, push back- ward.
CAUTION
Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.
Adjust the mirror so that you can just
see the rear of your vehicle in the mir-
ror.
To reduce glare from the headlights of
the vehicle behind you during night
driving, operate the lever on the lower
edge of the mirror.
Daylight driving—Lever at position 1
The reflection in the mirror has greater
clarity at this position.
Night driving—Lever at position 2
Remember that by reducing glare you also
lose some rear view clarity.
66
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
SECTION 1− 5
OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals Emergency flashers Front fog lights Instrument panel light control Interior light Windshield wipers and washer Rear window defogger
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
69
70
70
70
71
71
2005 MR2 from Aug. ’04Prod. (OM17527U)
67
04 09.01
Headlights and turn signals
SB14009a
tail,
license plate,
HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above Light reminder buzzer A buzzer will act as a reminder to turn the lights off when the driver’s door is opened if you remove the key with the headlights left on.
the
NOTICE
To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.
running
Daytime running light system The daytime light system can make it easier for others to see the front of your vehicle during the day. This sys- tem can be helpful in many different driv- ing conditions, but they can be especially helpful in the short periods after dawn and before sunset. This system will make your headlights come on at a reduced brightness when: D The engine is running. D The parking brake is released. D The headlight/turn signal lever knob is
in the “OFF” position or position 1.
To turn on the other exterior lights and instrument panel lights, twist the knob to position 1. Twist the knob to position 2 to turn the headlights to full intensity for night driving.
SB14019
High−low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.
the lever all
68
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
Emergency flashers
SB14011
SB14012
NOTICE
To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.
TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. See “Replacing light bulbs—” on page 228 in Section 7−3.
flashers,
turn on
the emergency
To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.
2005 MR2 from Aug. ’04Prod. (OM17527U)
69
04 09.01
Front fog lights
Instrument panel light control
Interior light
SB12093
SB14015a
SB14022
To turn on the front fog lights, push the switch. they will come on when the headlights and/or tail lights are turned on.
To adjust the brightness of the instru- ment panel lights, turn the switch.
To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—The light stays on all the time. “DOOR”—Turns the light on when either side door is opened. The light goes off when both the doors are closed. “OFF”—Turns the light off.
70
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
Windshield wipers and washer
Rear window defogger
SB14020
To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.
Lever position
Speed setting
Position 1
Position 2
Position 3
Intermittent
Slow
Fast
For a single sweep of push the lever up and release it.
the windshield,
the band upward to
The “INT TIME” band lets you adjust the wiping time interval when the wiper lever is in the intermittent position (position 1). Twist increase the time between sweeps, and downward to decrease it. To squirt washer fluid, pull the lever toward you. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” on page 227 in Section 7−3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on the windshield, which can block your vision.
the washer
NOTICE
Do not operate the wipers if the wind- shield the glass.
It may scratch
is dry.
SB14023
To defog or defrost the rear window,
push the switch.
The key must be in the “ON” position.
The thin heater wires on the inside of the
rear window will quickly clear the surface.
An indicator light will illuminate to indicate
the defogger is operating.
Push the switch once again to turn the
defogger off.
The system will automatically shut off af-
ter the defogger has operated about 15
minutes.
2005 MR2 from Aug. ’04Prod. (OM17527U)
71
04 09.01
Make sure you turn the defogger off when the window is clear. Leaving the defogger on for a long time could cause the battery to discharge, especially during stop−and− go driving. The defogger is not designed for drying rain water or for melting snow.
NOTICE
turn
z To prevent the battery from being the switch off
discharged, when the engine is not running. inside of the rear window, be careful not to scratch or damage the heater wires or connectors.
z When cleaning
the
z When
the soft top
is completely lowered, keep the rear window de- fogger turned off to avoid damage to the top.
72
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
SECTION 1− 6
OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge Engine coolant temperature gauge Tachometer Odometer and two trip meters Service reminder indicators and warning buzzers
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
74
74
75
75
77
2005 MR2 from Aug. ’04Prod. (OM17527U)
73
04 09.01
Fuel gauge
SB15009a
Low fuel level warning light
indicates
The gauge the approximate quantity of fuel remaining in the tank when the ignition switch is on. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. The needle moves when braking, acceler- ating or making turns. This is cause by the movement of the fuel in the tank. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible.
On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual. If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.
Engine coolant temperature gauge
SB15007a
The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves to the “H” position, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool. Your vehicle may overheat during severe operating conditions, such as: D Driving up a long hill on a hot day. D Reducing speed or stopping after high
speed driving.
D Idling for a long period with the air conditioning on in stop−and−go traffic.
74
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
If the engine coolant temperature gauge needle is not displayed, there may be a problem in the system. In this case, con- tact your Toyota dealer as soon as pos- sible.
NOTICE
z Do not remove the thermostat
in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to con- trol the flow of coolant to keep the temperature of the engine within the specified operating range.
z Do not continue driving with an overheated engine. See “If your vehicle overheats” on page 166 in Section 4.
Tachometer
Odometer and two trip meters
SB15008
SB15005
The tachometer indicates engine speed in thousands of rpm (revolutions per minute). Use it while driving to select correct shift points and to prevent en- gine lugging and over−revving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy. Remember, in most cases the slower the engine speed, the greater the fuel economy.
NOTICE
Do not let the indicator needle get into the red zone. This may cause severe engine damage.
This meter displays the odometer and two trip meters. 1. Odometer—Shows
total distance
the
the vehicle has been driven.
2. Two
trip meters—Show
two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.
fuel economy and
the other
2005 MR2 from Aug. ’04Prod. (OM17527U)
75
04 09.01
3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter then back B, the odometer each time you push. To reset the trip meter A to zero, dis- play then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.
trip meter A reading,
the
to
76
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
Service reminder indicators and warning buzzers
If the indicator or buzzer comes on...
Do this.
(a)
(b)
(c)
(d)
(e)
(f)
(g)
If parking brake is off, stop immediately and contact Toyota dealer.
(Indicator and buzzer)
Fasten driver’s seat belt.
Fasten passenger’s seat belt.
Stop and check.
Stop and check.
Take vehicle to Toyota dealer.
Low fuel level warning light
Fill up tank. (See “Fuel gauge” on page 74 in this Section.)
2005 MR2 from Aug. ’04Prod. (OM17527U)
77
04 09.01
If the indicator or buzzer comes on...
Do this.
(h)
(i)
(j)
(k)
(l)
(m)
(n)
(o)
78
Take vehicle to Toyota dealer immediately. If the vehicle cannot be driven, contact your Toyota dealer.
Take vehicle to Toyota dealer.
Close both the doors.
Take vehicle to Toyota dealer immediately.
Take vehicle to Toyota dealer.
Key reminder buzzer
Remove key.
Light reminder buzzer
Turn off lights.
Warning sequential manual transmission
function of
the
See “Sequential manual transmission” on page 85 in Section 1−6.
2005 MR2 from Aug. ’04Prod. (OM17527U)
04 09.01
(a) Brake System Warning Light This light comes on in the following cases when the ignition key is in the “ON” posi- tion. D When the parking brake is applied... This light comes on for a few seconds when to the “ON” position even after the parking brake is released. D When the brake fluid level is low...
ignition key
turned
the
is
CAUTION
It is dangerous to continue driving normally when the brake fluid level is low.
Have your vehicle checked at your Toyota dealer in the following case: D The light does not come on even if the parking brake is applied when the igni- tion key is in the “ON” position.
D The light does not come on even if the ignition key is turned on with the park- ing brake released.
A warning light turning on briefly during operation does not indicate a problem.
CAUTION
If either of the following conditions occurs, immediately stop your vehicle at a safe place and contact your Toyota dealer. D The
light does not turn off even after the parking brake is released while the engine is running. In this case, the brakes may not work properly and your stopping distance will become longer. De- press the brake pedal firmly and bring the vehicle to an immediate stop.
D The brake system warning light re- mains on together with the “ABS” warning light. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely un- stable during braking.
(b) Driver’s Seat Belt Reminder Light
and Buzzer
The light and buzzer act as a reminder to buckle up the driver’s seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes and buzzer sounds if the driver’s seat belt is not fastened. Unless the driver fastens the belt, the light continues flashing and the buzzer stops after about 4 to 8 seconds. (c) Passenger’s Seat Belt Reminder
Light
The light acts as a reminder to have the passenger buckle up the seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a passenger sits in the passenger seat and does not fasten the seat belt. Unless the passenger fastens the belt, the light stays flashing. However, if a passenger uses an additional seat cushion, the light may not flash even when is not buckled up. If luggage or other load is placed on the passenger seat, depending on its weight and how it is placed on the seat, built−in sensors in the seat cushion may detect the pressure, causing the reminder light to flash.
the seat belt
2005 MR2 from Aug. ’04Prod. (OM17527U)
79
04 09.01
(d) Discharge Warning Light This light warns that the battery is being discharged. If it comes on while you are driving, there is a problem somewhere in the charging system. The engine ignition will continue to oper- the battery ate, however, until is dis- charged. Turn off the air conditioning, blower, radio, etc., and drive directly to the nearest Toyota dealer or repair shop.
NOTICE
Do not continue driving if the engine drive belt is broken or loose.
(e) Low Engine Oil Pressure Warning
Light
This light warns that the engine oil pres-
sure is too low.
If it flickers or stays on while you are
driving, pull off the road to a safe place
and stop the engine immediately. Call a
Toyota dealer or qualified repair shop for
assistance.
flicker when
The
the engine is idling or it may come on
briefly after a hard stop. There
is no
cause for concern if it then goes out when
the engine is accelerated slightly.
80
light may occasionally
The light may come on when the oil level is extremely is not designed to indicate low oil level, and the oil level must be checked using the level dipstick.
low. It
NOTICE
Do not drive the warning light on—even for one block. It may ruin the engine.
the vehicle with
(f) Malfunction Indicator Lamp This lamp comes on when the ignition key is turned to the “ON” position and goes off after the engine starts. This means that the warning light system is operation properly. If the lamp remains on, or the lamp comes on while driving, first check the following. D Empty fuel tank
If the fuel tank is empty, refuel immedi- ately.
D Loose fuel tank cap
If the fuel tank cap is loose, securely tighten it.
These cases are temporary malfunctions. The malfunction indicator lamp will go off after taking several driving trips.
If the lamp does not go off even after several trips, contact your Toyota dealer as soon as possible. If the fuel tank is not empty or the fuel tank cap is not loose... D There is a problem somewhere in the engine, emission control system, elec- tronic throttle control system, automatic transmission electrical system or warn- ing light system itself.
Contact your Toyota dealer as soon as possible to service the vehicle. If engine speed does not increase when the accelerator pedal is depressed, there may be a problem somewhere in the elec- tronic throttle control system. At this time, vibration may occur. Howev- er, if you depress the accelerator pedal more firmly and slowly, you can drive your vehicle at low speeds. Have your vehicle checked by your Toyota dealer as soon as possible. Even if the abnormality of the electronic throttle control system is corrected during low speed driving, the system may not be recovered until the engine is stopped and the to “ACC” or ignition key