2005 Toyota ECHO Owners Manual

Jumper cable

Discharged battery

Negative terminal (“–” mark)

SY41001

SY41002

SF41001

Positive terminal (“+” mark)

Discharged battery

Booster battery

Positive terminal (“+” mark)

4. Make the cable connections in the or-

der a, b, c, d. a. Connect the clamp of the positive (red) jumper cable to the positive (+) terminal on the discharged battery. b. Connect the clamp at the other end of the positive (red) jumper cable to the positive (+) terminal on the booster battery.

Jumper cable

Booster battery

c. Connect the clamp of the negative (black) jumper cable to the negative (- ) terminal on the booster battery. d. Connect the clamp at the other end of the negative (black) jumper cable to a solid, stationary, unpainted, metallic point of the vehicle with the discharged battery. The recommended connecting point is shown in the following illustration:

Connecting point

Do not connect the cable to or near any part is cranked.

that moves when

the engine

CAUTION

the connections,

to When making avoid serious injury, do not lean over the battery or accidentally the jumper cables or clamps touch any- thing except the correct battery termi- nals or the ground.

let

182

2005 ECHO from Aug. ’04 Prod. (OM52636U)

5. Start your engine in the normal way. After starting, run it at about 2000 rpm for several minutes with the accelerator pedal lightly depressed.

6. Carefully disconnect the cables in the exact reverse order: the negative cable and then the positive cable.

7. Carefully dispose of the battery cover cloths—they may now contain sulfuric acid.

8. If removed, replace all the battery vent

plugs.

If the cause of your battery discharging is not apparent (for example, lights left on), you should have it checked at your Toyota dealer. If the first start attempt is not success- ful... Check jumper cables are tight. Recharge the discharged battery with the jumper cables connected for several minutes and restart your en- gine in the normal way. If another attempt is not successful, the battery may be depleted. Have it checked at your Toyota dealer.

the clamp on

that

the

If your engine stalls while driving If your engine stalls while driving... 1. Reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place.

2. Turn on your emergency flashers. 3. Try starting the engine again. If the engine will not start, see “If your vehicle will not start”.

CAUTION

If the engine is not running, the pow- er assist for the brakes and steering will not work so steering and braking will be much harder than usual.

If your vehicle overheats If your engine coolant temperature gauge indicates overheating, if you ex- perience a loss of power, or if you hear a loud knocking or pinging noise, the engine has probably overheated. You should follow this procedure... 1. Pull safely off the road, stop the ve- turn on your emergency hicle and flashers. Put the transmission in “P” (automatic) or neutral (manual) and ap- ply the parking brake. Turn off the air conditioning if it is being used.

2. If coolant or steam is boiling out of the radiator or reservoir, stop the engine. Wait until the steam subsides before opening the hood. If there is no coolant boiling over or steam, leave the engine running and make sure the electric cooling fan is operating. If it is not, turn the ignition off.

CAUTION

injury, keep To help avoid personal the hood closed until there is no steam. Escaping steam or coolant is a sign of very high pressure.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

183

6. After

the engine coolant

temperature has cooled to normal, again check the coolant level in the reservoir. If neces- sary, bring it up to half full again. Seri- ous coolant loss indicates a leak in the system. You should have it checked as soon as possible at your Toyota dealer.

If you have a flat tire— 1. Reduce your speed gradually, keeping a straight line. Move cau- tiously off the road to a safe place well away from the traffic. Avoid stopping on the center divider of a highway. Park on a level spot with firm ground.

2. Stop the engine and turn on your

emergency flashers.

3. Firmly set the parking brake and put the transmission in “P” (auto- matic) or reverse (manual).

4. Have everyone get out of the ve- hicle on the side away from traffic. 5. Read the following instructions

thoroughly.

3. Look for obvious coolant leaks from the radiator, hoses, and under the vehicle. However, note that water draining from the air conditioning is normal if it has been used.

CAUTION

the engine

When is running, keep hands and clothing away from the moving fan and engine drive belts.

4. If the coolant is leaking, stop the en- gine immediately. Call a Toyota dealer for assistance.

5. If there are no obvious leaks, check the coolant reservoir. If it is dry, add coolant to the reservoir while the en- gine is running. Fill it about half full. For the coolant type see “Coolant type selection” on page 224 in Section 7- 2.

CAUTION

Do not attempt to remove the radiator cap when the engine and radiator are hot. Serious injury could result from scalding hot fluid and steam blown out under pressure.

184

2005 ECHO from Aug. ’04 Prod. (OM52636U)

NOTICE

Do not continue driving with a deflated tire. Driving even a short distance can damage a tire and wheel beyond repair.

CAUTION

When jacking, be sure to observe the following to reduce the possi- bility of personal injury: (cid:1) Follow jacking instructions. (cid:1) Do not put any part of your body under the vehicle sup- ported by the jack. Personal in- jury may occur.

(cid:1) Do not start or run the engine while your vehicle is supported by the jack.

(cid:1) Stop the vehicle on a level firm ground, firmly set the parking brake and put the transmission in “P” (automatic) or reverse (manual). Block the wheel diag- onally opposite to the one be- ing changed if necessary.

(cid:1) Make sure to set the jack prop- erly in the jack point. Raising the vehicle with jack improper- ly positioned will damage the vehicle or may allow the ve- hicle to fall off the jack and cause personal injury.

(cid:1) Never get under the vehicle when the vehicle is supported by the jack alone.

(cid:1) Use the jack only for lifting your vehicle during wheel changing.

(cid:1) Do not raise the vehicle with

someone in the vehicle.

(cid:1) When raising the vehicle, do not put an object on or under the jack.

(cid:1) Raise the vehicle only high enough to remove and change the tire.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

185

SU41031

Compact spare tire The compact spare tire is designed for temporary emergency use only. The compact spare tire is identified by wording “TEMPORARY USE ONLY” molded into the sidewall of the tire. To keep the compact spare tire no- ticeable, do not hide the wheel by a wheel cover or such.

distinctive

the

The compact spare tire saves space in your luggage compartment, and its lighter weight helps to improve fuel economy and permits easier installa- tion in case of a flat tire. The compact spare tire can be used many times, if necessary. It has tread life of up to 4800 km (3000 miles) de- pending on road conditions and your driving habits. When tread wear indi- cators appear on the tire, replace the tire. See also the tire information in Sec- tion 7- 2 for details on the tread wear indicators and other service informa- tion.

CAUTION

(cid:1) The compact spare tire was de- signed especially for your To- yota. Do not use it on any other vehicle.

(cid:1) Do not use more than one com- pact spare tire at the same time.

(cid:1) The pressure for the compact spare tire must be 420 kPa (4.2
kgf/cm2 or bar, 60 psi).

(cid:1) Do not exceed 80 km/h (50
mph) when driving with the compact spare tire.

(cid:1) The standard tire should be re- paired and reinstalled as soon as possible.

(cid:1) Avoid sudden acceleration, sudden deceleration and sharp turns with the compact spare tire.

186

2005 ECHO from Aug. ’04 Prod. (OM52636U)

—Required tools and spare tire

SM41004a

SU41028a

NOTICE

Your ground clearance is re- duced when the compact spare tire is installed so avoid driving over obstacles and drive slowly on rough, unpaved roads and speed bumps. Also, do not at- tempt to go through an auto- matic car wash as the vehicle may get caught, resulting in damage.

1. Get the required

tools and

spare tire. Vehicles with compact spare tire

1. Jack handle 2. Wheel nut wrench 3. Jack 4. Spare tire

To prepare yourself for an emergency, you should familiarize yourself with the use of the jack, each of the tools and their storage locations.

Turn the jack joint by hand. To remove: Turn the joint in direction 1 until the jack is free. To store: Turn the joint in direction 2
until the jack is firmly secured to pre- vent it flying forward during a collision or sudden braking.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

187

—Blocking the wheel

—Removing wheel ornament (steel wheels)

SU41052a

SU41008

SY41010

To remove the spare tire: 1. Remove the spare tire cover. 2. Loosen the bolt and remove it. Then take the spare tire out of the vehicle. When storing the spare tire, put it in place with the outer side of the wheel facing up. Then secure the tire by re- peating the above removal steps in reverse order to prevent it from flying forward during a collision or sudden braking.

2. Block the wheel diagonally op- posite the flat tire to keep the vehicle from rolling when it is jacked up.

When blocking the wheel, place a wheel block in front of one of the front wheels or behind one of the rear wheels.

3. Remove the wheel ornament. Pry off the wheel ornament, using the beveled end of the wheel nut wrench as shown.

CAUTION

Do not try to pull off the orna- ment by hand. Take due care in handling the ornament to avoid unexpected personal injury.

188

2005 ECHO from Aug. ’04 Prod. (OM52636U)

—Loosening wheel nuts

—Positioning the jack

SY41012

CAUTION

Never use oil or grease on the bolts or nuts. The nuts may loos- en and the wheels may fall off, which could cause a serious ac- cident.

SU41012

4. Loosen all the wheel nuts. Always loosen the wheel nuts before raising the vehicle. The nuts turn counterclockwise to loosen. To get maximum leverage, fit the wrench to the nut so that the han- dle is on the right side, as shown above. Grasp the wrench near the end of the handle and pull up on the handle. Be careful that the wrench does not slip off the nut. Do not remove the nuts yet—just un- screw them about one- half turn.

5. Position the jack at the correct

jack point as shown.

Make sure the jack is positioned on a level and solid place.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

189

—Raising your vehicle

—Changing wheels

SY41014a

CAUTION

Never get under the vehicle when the vehicle is supported by the jack alone.

SY41015

6. After making sure that no one is in the vehicle, raise it high enough so that the spare tire can be installed.

Remember you will need more ground clearance when putting on the spare tire than when removing the flat tire. To raise the vehicle, insert the jack handle into the jack (it is a loose fit) and turn it clockwise. As the jack touches the vehicle and begins to lift, double- check that it is properly posi- tioned.

7. Remove the wheel nuts and

change tires.

Lift the flat tire straight off and put it aside. Roll the spare wheel into position and align the holes in the wheel with the bolts. Then lift up the wheel and get at least the top bolt started through its hole. Wiggle the tire and press it back over the other bolts.

190

2005 ECHO from Aug. ’04 Prod. (OM52636U)

—Reinstalling wheel nuts

SY41016

SY41017

CAUTION

Never use oil or grease on the bolts or nuts. Doing so may lead to overtightening the nuts and damaging the bolts. The nuts may loosen and the wheels may fall off, which could cause a seri- ous accident. If there is oil or grease on any bolt or nut, clean it.

Before putting on wheels, remove any corrosion on the mounting surfaces with a wire brush or such. Installation of wheels without good metal- to- met- al contact at the mounting surface can cause wheel nuts to loosen and eventually cause a wheel to come off while driving.

8. Reinstall all the wheel nuts fin-

ger tight.

Reinstall the wheel nuts (tapered end inward) and tighten them as much as you can by hand. Press back on the tire and see if you can tighten them more.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

191

—Lowering your vehicle

—Reinstalling wheel ornament (steel wheel)

SU41127

9. Lower the vehicle completely

and tighten the wheel nuts.

Turn the jack handle counterclock- wise to lower the vehicle. Use only the wheel nut wrench to tighten the nuts. Do not use other tools or any additional leverage other than your hands, such as a hammer, pipe or your foot. Make sure the wrench is securely engaged over the nut. Tighten each nut a little at a time in the order shown. Repeat the process until all the nuts are tight.

192

CAUTION

(cid:1) When

lowering the vehicle, make sure all portions of your body and all other persons around will not be injured as the vehicle is lowered to the ground.

(cid:1) Have the wheel nuts tightened with torque wrench to 103 N·m (10.5 kgf·m, 76 ft·lbf), as soon as possible after changing wheels. Otherwise, the nuts may loosen and the wheels may fall off, which could cause a serious accident.

SY41019

10.Reinstall the wheel ornament. 1. Put the wheel ornament into posi-

tion. On some models, align the cutout of the wheel ornament with the valve stem as shown.

2. Press hand firmly on one side of wheel ornament and then firmly tap the other side around the edge of wheel ornament with the heel of your hand to snap into place.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

CAUTION

Take due care in handling the or- nament to avoid unexpected per- sonal injury.

CAUTION

Before driving, make sure all the tools, jack and flat tire are se- curely in place in their storage location to reduce the possibility of personal injury during a colli- sion or sudden braking.

—After changing wheels 11. Check the air pressure of the re-

placed tire.

Adjust the air pressure to the specifi- cation designed in Section 8. If the pressure is lower, drive slowly to the nearest service station and fill to the correct pressure. Do not forget to reinstall the tire valve cap as dirt and moisture could get into the valve core and possibly cause air leakage. If the cap is missing, have a new one put on as soon as possible. 12.Restow all the tools, jack and

flat tire securely.

As soon after changing wheels as possible, tighten the wheel nuts to the torque specified in Section 8 with a torque wrench and have a technician repair the flat tire.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

193

If your vehicle becomes stuck If your vehicle becomes stuck in snow, mud, sand, etc., then you may attempt to rock the vehicle free by moving it forward and backward.

CAUTION

Do not attempt to rock the vehicle free by moving it forward and back- ward if people or objects are any where near the vehicle. During the rocking operation the vehicle may suddenly move forward or backward as it becomes unstuck, causing injury or damage to nearby people or ob- jects.

NOTICE

If you rock your vehicle, observe the following precautions to prevent dam- age to the transmission and other parts. (cid:1) Do not depress the accelerator ped- al while shifting the selector lever or before the transmission is com- pletely shifted to forward or reverse gear.

(cid:1) Do not race the engine and avoid

spinning the wheels.

(cid:1) If your vehicle remains stuck after rocking the vehicle several times, consider other ways such as tow- ing.

SU41034

Aluminum wheels: Remove the wheel ornament from the flat tire before restowing the flat tire.

194

2005 ECHO from Aug. ’04 Prod. (OM52636U)

If your vehicle needs to be towed—

(a) Towing with wheel lift type truck—

—From front

—From rear

SU41054b

(b) Using flat bed truck

If towing is necessary, we recommend you to have it done by your Toyota dealer or a commercial tow truck ser- vice. In consultation with them, have your vehicle towed using either (a) or (b). Only when you cannot receive a towing service from a Toyota dealer or com- mercial tow truck service, tow your ve- hicle carefully in accordance with the instructions given in “—Emergency towing” in this Section. Proper equipment will help ensure that your vehicle is not damaged while being towed. Commercial operators are generally aware of local laws pertaining to towing. Your vehicle can be damaged is towed incorrectly. Although most operators know the correct procedure, it is possible to make a mistake. To avoid damage to your vehicle, make sure the following few precautions are observed. If necessary, show this page to the tow truck driver. TOWING PRECAUTIONS: Use a safety chain system for all towing, and abide by the state/provincial and local laws. The wheels and axle on the ground must be in good condition. If they are damaged, use a towing dolly.

the state/provincial and

if

it

(a) Towing with wheel lift type truck From front—Release the parking brake.

NOTICE

When lifting wheels, take care to en- sure adequate ground clearance for towing at the opposite end of the raised vehicle. Otherwise, the bumper and/or underbody of the towed vehicle will be damaged during towing.

From rear— (cid:1) Manual transmission:

We recommend using a towing dolly under the front wheels. If you do not use a towing dolly, place the ignition key in the “ACC” position and put the transmission in neutral.

NOTICE

Do not tow with the key removed or in the “LOCK” position when towing from the rear without a towing dolly. The steering lock mechanism is not strong enough to hold the front wheels straight.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

195

(cid:1) Automatic transmission:

Use a wheels.

towing dolly under

the

front

(c) Towing with sliding type

truck

—Emergency towing

NOTICE

Never tow a vehicle with an automatic transmission from the rear with the front wheels on the ground, as this may cause serious damage to the transmission.

(b) Using flat bed truck

SU41022

SU41023b

(c) Towing with sling type truck

Front

NOTICE

Do not tow with sling type truck, ei- ther from the front or rear. This may cause body damage.

196

SU41024a

Rear

2005 ECHO from Aug. ’04 Prod. (OM52636U)

If towing is necessary, we recommend you to have it done by your Toyota dealer or a commercial tow truck ser- vice. If a towing service is not available in an emergency, your vehicle may be temporarily towed by a cable or chain secured to either the emergency towing eyelet on the front of the vehicle or to the left emergency towing eyelet under the rear of the vehicle. Use extreme caution when towing vehicles. Vehicles with an automatic transmis- sion, use only the front towing eyelet when towing your vehicle. To towing eyelet, see “—Installing front towing eyelet” on page 198 in this Section.

install

front

the

NOTICE

(cid:1) Only use specified towing eyelet; otherwise your vehicle may be dam- aged.

(cid:1) Vehicles with an automatic trans- mission, never tow a vehicle from the rear with four wheels on the ground. This may cause serious damage to the transmission.

A driver must be in the vehicle to steer it and operate the brakes. Towing in this manner may be done only on hard- surfaced roads for a short dis- tance and at the wheels, axles, drive train, steering and brakes must all be in good condition.

low speeds. Also,

CAUTION

(cid:1) Use extreme caution when towing vehicles. Avoid sudden starts or er- ratic driving maneuvers which would place excessive stress on the emergency towing eyelets and tow- ing cable or chain. The eyelets and towing cable or chain may break and cause serious injury or dam- age.

(cid:1) In case of installing the front eyelet on the vehicle, be sure to tighten the front eyelet securely. If the eye- let is loose, it may come off when towing and result in death or seri- ous injury to the passenger in the front vehicle or damage to that ve- hicle.

NOTICE

(cid:1) Use only a cable or chain specifi- cally intended for use in towing ve- hicles. Securely fasten the cable or chain to the towing eyelet provided. (cid:1) Do not use the right rear eyelet. It

is not designed for towing.

Before towing, release the parking brake and put the transmission in neutral (manu- al) or “N” (automatic). The key must be in “ACC” (engine off) or “ON” (engine run- ning).

CAUTION

If the engine is not running, the pow- er assist for the brakes and steering will not work so steering and braking will be much harder than usual.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

197

—Installing front towing eyelet

SN41005a

SN41002a

SN41003a

1. Remove

the

front

towing eyelet as

shown in the illustrations.

the

2. Remove the front towing eyelet cover flat- is wrapped

on bladed screwdriver which with a cloth.

front bumper, using a

3. Secure the front towing eyelet to the hole on the bumper by turning clock- wise.

198

2005 ECHO from Aug. ’04 Prod. (OM52636U)

If you cannot shift automatic transmission selector lever

SN41004a

SU41032

SU41053

4. Tighten the front towing eyelet securely

by a wheel nut wrench.

CAUTION

When installing the eyelet on the ve- hicle, be sure to tighten the front eyelet securely. If the eyelet is loose, it may come off when being towed and result in death or serious injury.

though

If you cannot shift the selector lever out of “P” position to other positions even is de- pressed, use the shift lock override but- ton as follows: 1. Turn

the brake pedal

ignition key

the

to “LOCK” the parking

position. Make sure brake is applied.

2. Pry up the cover with a flat- bladed

screwdriver or equivalent.

3. Insert your finger into the hole to push down the shift lock override button. You can shift out of “P” position only while pushing the but- ton.

4. Shift into “N” position. 5. Insert the cover. 6. Start the engine. For your safety,

keep the brake pedal depressed.

Be sure to have the system checked by your Toyota dealer as soon as possible.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

199

in “Keys”

the suggestion given

If you lose your keys You can purchase a new key at your Toyota dealer if you can give them the key number. See Section 1- 2. If your keys are locked in the vehicle and you cannot get a duplicate, many Toyota dealers can still open the door for you, If you must using break a window in, we suggest breaking the smallest side window be- cause it is the least expensive to replace. Be extremely cautious to avoid cuts from the glass.

their special

to get

tools.

in

If you lose your wireless remote control transmitter You can purchase a new wireless re- mote control transmitter at your Toyota dealer. Have the registered identification numbers of your transmitters deleted from your ve- hicle by your Toyota dealer as soon as possible to avoid the possibility of theft or an accident. Then, have the identification number of your new transmitter registered. At the same time, you must bring all of the remaining transmitters to have them registered again as well. You can use the wireless remote control system with the new transmitter. Contact your Toyota dealer for detailed information.

200

2005 ECHO from Aug. ’04 Prod. (OM52636U)

SECTION 5

CORROSION PREVENTION AND APPEARANCE CARE Corrosion prevention and appearance care Protecting your Toyota from corrosion Washing and waxing your Toyota Cleaning the interior

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

202
203
205

2005 ECHO from Aug. ’04 Prod. (OM52636U)

201

Protecting your Toyota from corrosion Toyota, through its diligent research, de- sign and use of the most advanced technology available, helps prevent corro- sion and provides you with the finest qual- ity vehicle construction. Now, it is up to you. Proper care of your Toyota can help ensure long- term corrosion prevention. The most common causes of corrosion to your vehicle are: (cid:1) The accumulation of road salt, dirt and moisture in hard- to- reach areas under the vehicle.

(cid:1) Chipping of paint, or undercoating caused by minor accidents or by stones and gravel.

Care is especially important if you live in particular areas or operate your ve- hicle under certain environmental condi- tions: (cid:1) Road salt or dust control chemicals will accelerate corrosion, as will the pres- ence of salt in the air near the sea- coast or in areas of industrial pollution. (cid:1) High humidity accelerates corrosion es- pecially when temperatures range just above the freezing point.

(cid:1) Wetness or dampness to certain parts of your vehicle for an extended period of time, may cause corrosion even though other parts of the vehicle may be dry.

those components of

(cid:1) High temperatures will cause corrosion to the vehicle which do not dry quickly due to lack of proper ventilation.

The above signifies the necessity to keep your vehicle, particularly the underside, as clean as possible and to repair any dam- age to paint or protective coatings as soon as possible. To help prevent corrosion on your Toyota, follow these guidelines: Wash your vehicle frequently. It is, of course, necessary to keep your vehicle clean by regular washing, but to prevent corrosion, the following points should be observed: (cid:1) If you drive on salted roads

the winter or if you live near the ocean, you should hose off the undercarriage at least once a month to minimize cor- rosion.

in

(cid:1) High pressure water or steam is effec- tive for cleaning the vehicle’s underside and wheel housings. Pay particular attention to these areas as it is difficult to see all the mud and dirt. It will do more harm than good to simply wet the mud and debris without removing. The lower edge of doors, rocker panels and frame members have drain holes which should not be allowed to clog with dirt as trapped water in these areas can cause corrosion.

(cid:1) Wash the underside of the vehicle thor-

oughly when winter is over.

See “Washing and waxing your Toyota” for more tips. Check the condition of your vehicle’s paint and trim. If you find any chips or scratches in the paint, touch them up im- mediately to prevent corrosion from start- ing. If the chips or scratches have gone through the bare metal, have a qualified body shop make the repair.

202

2005 ECHO from Aug. ’04 Prod. (OM52636U)

Check the interior of your vehicle. Wa- ter and dirt can accumulate under the floor mats and could cause corrosion. Oc- casionally check under the mats to make sure the area is dry. Be particularly care- ful when transporting chemicals, cleans- ers, fertilizers, salt, etc.; these should be transported in proper containers. If a spill or leak should occur, immediately clean and dry the area. Use mud shields on your wheels. If you drive on salted or gravel roads, mud shields help protect your vehicle. Full- size shields, which come as near to the ground as possible, are the best. We recommend that the fittings and the area where the shields are installed be treated to resist corrosion. Your Toyota dealer will be happy to assist in supplying and installing the shields if they are recommended for your area. Keep your vehicle in a well ventilated garage or a roofed place. Do not park your vehicle in a damp, poorly venti- lated garage. If you wash your vehicle in the garage, or if you drive it covered with water or snow, your garage may be so damp as to cause corrosion. Even if your garage is heated, a wet vehicle can cor- rode if the ventilation is poor.

Washing and waxing your Toyota Washing your Toyota Keep your vehicle clean by regular washing. The following cases may cause weakness to the paint or corrosion to the body and parts. Wash your vehicle as soon as pos- sible. (cid:1) When driving in a coastal area (cid:1) When driving on a road sprinkled with

antifreeze

(cid:1) When exposed to coal tar, tree sap, bird droppings and carcass of an insect (cid:1) When driving in areas where there is a lot of smoke, soot, dust, iron dust or chemical substances

(cid:1) When the vehicle becomes remarkably

dirty with dust and mud Hand- washing your Toyota Work in the shade and wait until the vehicle body is not hot to the touch.

1. Rinse off loose dirt with a hose. Re- move any mud or road salt from the underside of the wheel wells.

the vehicle or

in

2. Wash with a mild car- wash soap, mixed according to the manufacturer’s instructions. Use a soft cotton mitt and keep it wet by dipping it frequently into the wash water. Do not rub hard—let the soap and water remove the dirt.

Fuel filler door: Do not apply water (high- pressure car wash, for example) at or near the fuel tank inlet with the fuel filler door opened. If the water enters the air vent, you may experience trouble with re- fueling or rough engine idling. Plastic wheel ornaments: The plastic wheel ornaments are damaged easily by organic substances. If any organic sub- stance splashes an ornament, be sure to wash it off with water and check if the ornament is damaged.

CAUTION

CAUTION

When cleaning under floor or chassis, be careful not to injure your hands.

Do not attach the heavily damaged plastic wheel ornament. It may fly off the wheel and cause accidents while the vehicle is moving.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

203

Aluminum wheels: Use only a mild soap or neutral detergent. Plastic bumpers: Wash carefully. Do not scrub with abrasive cleaners. The bumper faces are soft. Road turpentine or cleaners that are marked safe for painted surfaces.

tar: Remove with

NOTICE

Do not use organic substances (gaso- line, kerosene, benzine or strong sol- vents), which may be toxic or cause damage.

3. Rinse

thoroughly—dried

can cause streaking. In hot weather you may need to rinse each section right after you wash it.

soap

4. To prevent water spots, dry the vehicle using a clean soft cotton towel. Do not rub or press hard—you might scratch the paint.

Automatic car wash Your vehicle may be washed in an auto- matic car wash, but remember that the paint can be scratched by some types of brushes, unfiltered washing water, or the washing process itself. Scratching reduces paint durability and gloss, especially on darker colors. The manager of the car wash should be able to advise you wheth- er the process is safe for the paint on your vehicle.

NOTICE

To prevent damage to the antenna, make sure it is retracted before driv- ing your Toyota through an automatic car wash.

Waxing your Toyota Polishing and waxing is recommended to maintain the original beauty of your Toyota’s finish. Apply wax once a month or if the vehicle surface does not repel water well. 1. Always wash and dry the vehicle be- fore you begin waxing, even if you are using a combined cleaner and wax.

2. Use a good quality polish and wax. If the finish has become extremely weath- ered, use a car- cleaning polish, fol- lowed by a separate wax. Carefully fol- low the manufacturer’s instructions and precautions. Be sure to polish and wax the chrome trim as well as the paint. the vehicle again when water does not bead but remains on the sur- face in large patches.

3. Wax

NOTICE

Always remove the plastic bumpers if your vehicle is re-painted and placed in a high heat paint waxing booth. High temperatures could damage the bumpers.

204

2005 ECHO from Aug. ’04 Prod. (OM52636U)

Cleaning the interior

CAUTION

(cid:1) Vehicles with side airbags:

Be careful not to splash water or spill liquid on the floor. This may prevent the side airbags from acti- vating correctly, resulting in serious injury.

(cid:1) Do not wash the vehicle floor with water, or allow water to get onto the floor when cleaning the vehicle interior or exterior. Water may get into audio components or other electrical components above or un- der the floor carpet (or mat) and cause a malfunction; and it may cause body corrosion.

Vinyl interior The vinyl upholstery may be easily cleaned with a mild soap or detergent and water. First vacuum over the upholstery to re- move loose dirt. Then, using a sponge or soft cloth, apply the soap solution to the vinyl. After allowing it to soak in for a few minutes to loosen the dirt, remove the dirt and wipe off the soap with a clean damp cloth. If all the dirt do not come off, re- peat the procedure. Commercial foaming- type vinyl cleaners are also available which work well. Follow the manufacturer’s instructions.

NOTICE

Do not use solvent, thinner, gasoline or window cleaner on the interior.

to

foam- type shampoo

Carpets Use a good clean the carpets. Begin by vacuuming thoroughly to remove as much dirt as possible. Several types of foam cleaners are available; some are in aerosol cans and others are powders or liquids which you mix with water to pro- duce a foam. To shampoo the carpets, use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water—the best results are obtained by keeping the carpet as dry as possible. Read the shampoo instructions and follow them closely. Seat belts The seat belts may be cleaned with mild soap and water or with lukewarm water. Use a cloth or sponge. As you are clean- ing, check the belts for excessive wear, fraying, or cuts.

NOTICE

(cid:1) Do not use dye or bleach on the

belts—it may weaken them.

(cid:1) Do not use the belts until they be-

come dry.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

205

Windows The windows may be cleaned with any household window cleaner.

NOTICE

When cleaning the inside of the win- dows, be careful not to scratch or damage the heater wires on the rear window.

Air conditioning control panel, audio panel, instrument panel, console panel, and switches Use a soft damp cloth for cleaning. Soak a clean soft cloth in water or luke- warm water then lightly wipe off dirt.

NOTICE

(cid:1) Do not use organic substances (sol- vents, kerosene, alcohol, gasoline, etc.) or alkaline or acidic solutions. These chemicals can cause discol- oring, staining or peeling of the surface.

(cid:1) If you use cleaners or polishing agents, make sure their ingredients do not include the substances men- tioned above.

(cid:1) If you use a liquid car freshener, do not spill the liquid onto the ve- hicle’s interior surfaces. It may con- tain the ingredients mentioned above. Immediately clean any spill using the method mentioned above.

If you have any questions about the cleaning of your Toyota, your local Toyota dealer will be pleased to answer them.

206

2005 ECHO from Aug. ’04 Prod. (OM52636U)

SECTION 6

VEHICLE MAINTENANCE AND CARE Vehicle maintenance and care Maintenance requirements General maintenance Does your vehicle need repairing? Emissions inspection and maintenance (I/M) programs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

208
209
211
212

For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

207

Maintenance requirements Your Toyota vehicle has been designed for fewer maintenance requirements with long- er service intervals to save both your time and money. However, each regular mainte- nance, as well as day- to- day care, is more important than ever before to ensure smooth, trouble- free, safe, and economical drivings. It is the owner’s responsibility to make sure the specified maintenance, including general maintenance service, is performed. Note that both the new vehicle and emis- sion control system warranties specify that proper maintenance and care must be per- formed. See “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supple- ment” for complete warranty information. General maintenance General maintenance items are those day- to- day care practices that are important to your vehicle for proper operation. It is the owner’s responsibility to insure that the general maintenance items are performed regularly. These checks or inspections can be done either by yourself or a qualified technician, or if you prefer, your Toyota dealer will be pleased to do them at a nominal cost.

Scheduled maintenance The scheduled maintenance items listed in the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement” are those required to be serviced at regular inter- vals. For details of your maintenance schedule, read the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any replacement parts used for maintenance or for the repair of the emission control system be Toyota supplied. The owner may elect to use non- Toyota supplied parts replacement pur- poses without invalidating the emission control system warranty. However, use of replacement parts which are not of equivalent quality may impair the effec- tiveness of the emission control sys- tems. You may have maintenance, replacement, or repair of the control devices and system performed by any automotive repair individual without invalidating this warranty. See “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement” for complete warranty information.

establishment

emission

elect

also

for

or

to

Where to go for service? Toyota technicians are well- trained spe- cialists and are kept up to date with the latest service information through technical bulletins, service tips, and in- dealership training programs. They learn to work on Toyotas before they work on your vehicle, rather than while they are working on it. You can be confident that your Toyota dealer’s service department performs the best job to meet the maintenance require- ments on your vehicle—reliably and eco- nomically. Your copy of the repair order is proof that all required maintenance has been per- formed for warranty coverage. If any prob- lems should arise with your vehicle while under warranty, your Toyota dealer will promptly take care of it. Again, be sure to keep a copy of the repair order for any service performed on your Toyota. What about do- it- yourself maintenance? Many of the maintenance items are easy to do yourself if you have a little mechani- cal ability and a few basic automotive tools. Simple instructions for how to per- form them are presented in Section 7.

208

2005 ECHO from Aug. ’04 Prod. (OM52636U)

a

you are

If skilled do- it- yourself mechanic, the Toyota service manuals are recommended. Please be aware that do- it- yourself maintenance can affect your warranty coverage. See “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement” for the details.

the

items

listed,

General maintenance Listed below are the general maintenance items that should be performed as fre- quently as specified. In addition to check- ing if you notice any unusual noise, smell or vibration, you should investigate the cause or take your vehicle to your Toyota dealer or a quali- fied service shop immediately. It is recom- mended that any problem you notice be brought to the attention of your dealer or the qualified service shop for their advice.

CAUTION

Make these checks only with ade- quate ventilation if you run the en- gine.

IN THE ENGINE COMPARTMENT Items listed below should be checked from time to time, e.g. each time when refueling. Washer fluid Make sure there is sufficient fluid in the tank. See Section 7- 3 for additional in- formation.

Engine coolant level Make sure the coolant level is between the “FULL” and “LOW” lines on the see- through reservoir when the engine is cold. See Section 7- 2 for additional information. Radiator, condenser, and hoses Check that the front of the radiator and condenser are clean and not blocked with leaves, dirt or insects. See Section 7- 2
for additional information. Battery electrolyte level Make sure the electrolyte level of all bat- tery cells is between upper and lower lev- el lines on the case. Add only distilled water when replenishing. See Section 7- 3
for additional information. Brake fluid level Make sure the brake fluid level is correct. See Section 7- 2 for additional information. Engine oil level Check the level on the dipstick with the engine turned off and the vehicle parked on a level spot. See Section 7- 2 for addi- tional information. Power steering fluid level Check the level through the reservoir. The level should be in the “HOT” or “COLD” range depending on the fluid temperature. See Section 7- 2 for additional information.

2005 ECHO from Aug. ’04 Prod. (OM52636U)

209

Exhaust system If you notice any change in the sound of the exhaust or smell exhaust fumes, have the cause located and corrected immedi- ately. (See “Engine exhaust cautions” in Section 2.) INSIDE THE VEHICLE Items listed below should be checked regularly, e.g. while performing periodic services, cleaning the vehicle, etc. Lights Make sure the headlights, stop lights, tail lights, turn signal lights, and other lights are all working. Check headlight aim. Service reminder indicators and warning buzzers Check that all service reminder indicators and warning buzzers function properly. Steering wheel Be alert for changes in steering condition, such as hard steering or strange noise.

the

that

Seats Check that all front seat controls such as seat adjusters, seatback recliner, etc. op- erate smoothly and that all latches lock securely in any position. Check that the head restraints move up and down smoothly and that the locks hold securely in any latched position. For folding- down rear seatbacks, check latches lock securely. Seat belts Check that the seat belt system such as buckles, retractors and anchors operate properly and smoothly. Make sure that the belt webbings are not cut, frayed, worn or damaged. Accelerator pedal Check the pedal for smooth operation and uneven pedal effort or catching. Clutch pedal Check the pedal for smooth operation. Brake pedal Check the pedal for smooth operation and that the pedal has the proper clearance. Check the brake booster function. Brakes In a safe place, check that the brakes do not pull to one side when applied.

Parking brake Check that the lever has the proper travel and that, on a safe incline, your vehicle is held securely with only the parking brake applied. Automatic transmission “Park” mecha- nism Check the lock release button of the se- lector lever for proper and smooth opera- tion. On a safe incline, check that your vehicle is held securely with the selector lever in “P” position and all brakes re- leased. OUTSIDE THE VEHICLE Items listed below should be performed from time, unless otherwise specified. Fluid leaks Check underneath for leaking fuel, oil, wa- ter or other the vehicle has been parked for a while. If you smell fuel fumes or notice any leak, have the cause found and corrected immediately. Doors and engine hood Check that all doors including trunk lid operate smoothly and all latches lock se- curely. Make sure the engine hood sec- ondary latch secures the hood from open- ing when the primary latch is released.

fluid after

time

to

210

2005 ECHO from Aug. ’04 Prod. (OM52636U)

Tire pressure Check the pressure with a gauge ev- ery two weeks, or at least once a month. See Section 7- 2 for additional information. Tire surface and wheel nuts Check the tires carefully for cuts, damage or excessive wear. See Sec- tion 7- 2 for additional information. When checking the tires, make sure no nuts are missing, and check the nuts for looseness. Tighten them if necessary. Tire rotation Rotate the tries according to the maintenance schedule. (For sched- uled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supple- ment”.)

tip- offs

for changes

Does your vehicle need repairing? Be on the alert in perfor- mance, sounds, and visual that indicate service is needed. Some impor- tant clues are as follows: (cid:1) Engine missing, stumbling, or pinging (cid:1) Appreciable loss of power (cid:1) Strange engine noises (cid:1) A leak under the vehicle (however, wa- ter dripping from the air conditioning after use is normal.)

If you notice any of these clues, take your vehicle to your Toyota dealer as soon as possible. It probably needs adjustment or repair.

CAUTION

Do not continue driving with the ve- hicle unchecked. It could result in se- rious vehicle damage and possibly personal injury.

(cid:1) Change

in exhaust sound (This may indicate a dangerous carbon monoxide leak. Drive with the windows open and have the exhaust system checked im- mediately.)

(cid:1) Flat- looking tire; excessive tire squeal

when cornering; uneven tire wear

(cid:1) Vehicle pulls to one side when driving

straight on a level road

(cid:1) Strange noises related to suspension

movement

(cid:1) Loss of brake effectiveness; spongy feeling brake or clutch pedal; pedal al- most touches floor; vehicle pulls to one side when braking

(cid:1) Engine coolant temperature continually

higher than normal

2005 ECHO from Aug. ’04 Prod. (OM52636U)

211

The malfunction indicator lamp will go off after taking several driving trips, but the error code in the OBD system will not be cleared unless about 40 trips or more are taken. If your vehicle does not pass the I/M test even the malfunction indicator lamp does not come on, contact your Toyota dealer to prepare the vehicle for re- testing.

indicator

the malfunction

in- include OBD

Emissions inspection and maintenance (I/M) programs Some states have vehicle emission spection programs which (On- Board Diagnostics) checks. The OBD system monitors the operation of the emission control system. When the OBD system determines that a problem exists somewhere in the emission control system, lamp comes on. In this case, your vehicle may the I/M test and need to be not pass repaired. Contact your Toyota dealer to service the vehicle. Even lamp does not come on, your vehicle may not pass readiness codes have not been set in the OBD system. Readiness codes are automatically set during ordinary driving. However, when the battery is disconnected or run down, the codes are erased. Also, depending on your driving habits, the codes may not be completely set. Also, if the malfunction indicator lamp had come on recently due to temporary mal- function such as a loose fuel tank cap, your vehicle may not pass the I/M test.

the malfunction

indicator

test as

I/M

the

if

212

2005 ECHO from Aug. ’04 Prod. (OM52636U)

SECTION 7- 1

DO- IT- YOURSELF MAINTENANCE Introduction Engine compartment overview Fuse locations Do- it- yourself service precautions Parts and tools Positioning the jack

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

214
215
215
217
218

2005 ECHO from Aug. ’04 Prod. (OM52636U)

213

Engine compartment overview

SU71011

1. Windshield washer fluid tank

2. Engine oil filler cap

3. Power steering fluid reservoir

4. Brake fluid reservoir

5. Battery

6. Fuse blocks

7. Engine coolant reservoir

8. Radiator

9. Condenser

10. Electric cooling fan

11. Engine oil level dipstick

214

2005 ECHO from Aug. ’04 Prod. (OM52636U)

Fuse locations

SU71002b

Spare fuses

SU71006a

SY71004a

Do- it- yourself service precautions If you perform maintenance by yourself, be sure to follow the correct procedure given in this Section. You should be aware that improper or in- complete servicing may result in operating problems. Performing do- it- yourself maintenance during the warranty period may affect your warranty coverage. Read the separate Toyota Warranty statement for details and suggestions. This Section gives for those items that are relatively easy for an owner to perform. As explained in Section 6, there are still a number of items that must be done by a qualified technician with special tools. For information on tools and parts for do- it- yourself maintenance, see “Parts and tools”. Utmost care should be taken when work- ing on your vehicle to prevent accidental injury. Here are a few precautions that you should be especially careful to ob- serve:

instructions only

2005 ECHO from Aug. ’04 Prod. (OM52636U)

215

CAUTION

(cid:1) When the engine is running, keep hands, clothing, and tools away from the moving fan and engine drive rings, watches, and ties is advisable.)

(Removing

belts.

(cid:1) Right after driving,

the engine compartment—the engine, radiator, exhaust manifold and spark plug boots, etc.—will be hot. So be care- ful not to touch them. Oil, fluids and spark plugs may also be hot.

(cid:1) If the engine is hot, do not remove the radiator cap or loosen the drain plugs to prevent burning yourself.

(cid:1) Do not

leave anything

that may burn easily, such as paper or rags, in the engine compartment.

(cid:1) Do not smoke, cause sparks or al- low open flames around fuel or the battery. Their fumes are flammable. (cid:1) Be extremely cautious when work- ing on the battery. It contains poi- sonous and corrosive sulfuric acid.

(cid:1) Dispose of used oil and filter only in a safe and acceptable manner. Do not dispose of used oil and fil- ter in household trash, in sewers or onto the ground. Call your dealer or a service station information concerning recycling or disposal.

for

fluid

(cid:1) Take care when filling the brake and clutch reservoirs because brake fluid can harm your eyes and damage painted surfaces. fluid gets in your eyes, flush your eyes with clean water immediately. If you still feel uncomfortable with your eyes, go to the doctor.

If

(cid:1) Do not get under your vehicle with just the body jack supporting it. Al- ways use automotive jack stands or other solid supports.

(cid:1) Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on, the electric cooling fans will automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.

(cid:1) Use eye protection whenever you work on or under your vehicle where you may be exposed to flying or falling material, fluid spray, etc. (cid:1) Used engine oil contains potentially harmful contaminants which may cause skin disorders such as in- flammation or skin cancer, so care should be taken to avoid prolonged and repeated contact with it. To re- move used engine oil from your skin, wash thoroughly with soap and water.

(cid:1) Do not

leave used oil within the

reach of children.

216

2005 ECHO from Aug. ’04 Prod. (OM52636U)

(cid:1) Do not overfill automatic transmis- sion fluid, or the transmission could be damaged.

(cid:1) Do not drive with the air cleaner filter removed, or excessive engine wear could result. Also backfiring could cause a fire in the engine compartment.

(cid:1) Be careful not to scratch the glass

surface with the wiper frame.

(cid:1) When closing the engine hood, check to see that you have not for- gotten any tools, rags, etc.

NOTICE

(cid:1) Remember that battery and ignition cables carry high currents or volt- ages. Be careful of accidentally causing a short circuit.

(cid:1) Add only “Toyota Super Long Life Coolant” or similar high quality eth- ylene glycol based non-silicate, non-amine, non-nitrite, and non-bo- rate coolant with long-life hybrid organic acid technology to fill the radiator. “Toyota Super Long Life Coolant” is a mixture of 50% cool- ant and 50% deionized water (for the U.S.A.) or 55% coolant and 45% deionized water (for Canada).

(cid:1) If you spill some of the coolant, be sure to wash it off with water to prevent it from damaging the parts or paint.

(cid:1) Do not allow dirt or anything else to fall through the spark plugholes. (cid:1) Use only spark plugs of the speci- fied type. Using other types will cause engine damage, loss of per- formance or radio noise.

Parts and tools Here is a list of parts and tools you will need to perform do- it- yourself mainte- nance. Remember all Toyota parts are de- signed in metric sizes, so your tools must be metric. CHECKING THE ENGINE OIL LEVEL Parts (if level is low): (cid:1) Engine

SL “Energy- Conserving” ILSAC multigrade having viscosity proper for your climate

grade or

API

oil

Tools: (cid:1) Rag or paper towel (cid:1) Funnel (only for adding oil) CHECKING THE ENGINE COOLANT LEVEL Parts (if level is low): (cid:1) “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non- silicate, non- amine, non- ni- trite, and non- borate coolant with long- life hybrid organic acid technology. “Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deion- ized water (for the U.S.A.) or 55% coolant and 45% deionized water (for Canada).

Tools: (cid:1) Funnel (only for adding coolant)

2005 ECHO from Aug. ’04 Prod. (OM52636U)

217

CHECKING BRAKE FLUID Parts (if level is low): (cid:1) SAE J1703 or FMVSS No.116 DOT 3

brake fluid

Tools: (cid:1) Rag or paper towel (cid:1) Funnel (only for adding fluid) CHECKING POWER STEERING FLUID Parts (if level is low): (cid:1) Automatic

transmission

fluid

DEXRONII or III

Tools: (cid:1) Rag or paper towel (cid:1) Funnel (only for adding fluid) CHECKING BATTERY CONDITION Tools: (cid:1) Warm water (cid:1) Baking soda (cid:1) Grease (cid:1) Conventional wrench

(for

terminal

clamp bolts)

CHECKING AND REPLACING FUSES Parts (if replacement is necessary): (cid:1) Genuine Toyota fuse or equivalent with

same amperage rating as original

ADDING WASHER FLUID Parts: (cid:1) Water (cid:1) Washer fluid containing antifreeze (for

winter use)

Tools: (cid:1) Funnel REPLACING LIGHT BULBS Parts: (cid:1) Bulb with same number and wattage rating as original in “Replacing light bulbs” in Section 7- 3.)

charts

(See

Positioning the jack

Do not jack up

Do not jack up

SU41101a

Lower back outer panel (protrusion) Attachment

When jacking up your vehicle with the jack, position jack correctly as shown in the illustration. Jack position . . . . . . . . . .

the

Front—Front suspension member Rear—Lower back outer panel

Support position for Pantograph jack . . . . . .