86
86
106
2000 ECHO (OM52411U)
85
ECHO_U
Reference
SU17001
SU17003
Type 1: AM·FM ETR radio/cassette·com- pact disc auto changer controller
Type 3: AM·FM ETR radio/cassette player/ compact disc player/compact disc auto changer controller
SU17002
Type 2: AM·FM ETR radio/cassette player/ compact disc auto changer controller
86
2000 ECHO (OM52411U)
“TAPE”,
turn on
“FM1·2”,
“AM”, to
Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR/VOL” or “PWR·VOL” to turn the audio system on and off. Push “AUX” pushing “PWR/VOL” or “PWR·VOL”. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or com- pact disc. function was pre- viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “CD” or “AUX” if the system is already on but you want to switch from one function to anoth- er.
“CD” or function without
If another
“FM1·2”,
“TAPE”,
“AM”,
that
ECHO_U
TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange, and bass levels. In fact, different kinds of music and vocal programs usually sound better with differ- ent mixes of treble, midrange and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.
YOUR RADIO ANTENNA To remove the antenna, carefully turn it counterclockwise. To lower the power antenna, turn off the audio system by pushing “PWR/VOL” or “PWR·VOL”, or to “LOCK”. YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should be to the right.
turn the ignition key
NOTICE
Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.
YOUR COMPACT DISC PLAYER When you insert a disc, gently push it in with the label side up. (The player will automatically eject a disc if the label side is down.) The compact disc player will play from track 1 through the end of the disc. Then it will play from track 1 again.
NOTICE
Never try to disassemble or oil any part of the compact disc player. Do not insert anything except a compact disc into the slot.
2000 ECHO (OM52411U)
87
ECHO_U
—Controls and features
(cid:1)Type 1
Details of specific buttons, controls, and features are described in the alphabetical listing that follows.
SU17004
88
2000 ECHO (OM52411U)
ECHO_U
(Reverse/Fast forward buttons)
the
the
fast
Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”. If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto- re- verse feature. Compact Disc Player If you want forward or reverse to fast through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing.
AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation. CTRL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. For “CTRL appears on knob to suit your preference. The display will show the “BAS -5” to “BAS 5”. For high- pitch “CTRL appears on knob to suit your preference. The display will show the “TRE -5” to “TRE 5”.
tone adjustment, push / MODE” repeatedly until “TRE” the
tone adjustment, push / MODE” repeatedly until “BAS” the
the display. Then
the display. Then
to adjust
low- pitch
is used
range
range
turn
turn
from
from
tone
2000 ECHO (OM52411U)
89
to preset and
1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).
(Program)
Push “ ” to select the other side of a cassette tape. The display indicates which ” indicates side is currently selected (“ top side, “ Auto- reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.
” indicates bottom side). feature: After
ECHO_U
the
from
range
to adjust
is also used
left/right adjustment, push “CTRL
Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers. For front/rear adjustment, push “CTRL / MODE” repeatedly until “FAd” appears on the display. Then turn the knob to adjust the front/rear balance. The display will show “FAd- F7” to “FAd- R7”. For MODE” repeatedly until “BAL” appears on the display. Then turn the knob to adjust the left/right balance. The display will show “BAL- L7” to “BAL- R7”. AUX (Auxiliary button) This button is used to operate each player when a cassette tape player, compact disc player or compact disc auto changer is equipped with this radio player. With cassette tape player Push ”AUX” to switch from radio to cas- sette operation. If the audio system is off, you can turn on the cassette player by pushing ”AUX”. In both cases, a cassette must already be loaded in the player.
range
from
the
in
loaded
With compact disc player or compact disc auto changer Push “AUX” to switch from radio to com- pact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “AUX”. In both cases, a disc must already be the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each time you push “AUX”, the system changes to the automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages. If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc.
inserted up- side down. Clean
loaded
inside
it the
is
90
2000 ECHO (OM52411U)
If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer. DISC (cid:2)(cid:1) Compact disc auto changer only— By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display. Dolby(cid:3) If you are listening to a tape that was recorded with Dolby(cid:3) B Noise Reduction, push the button marked with the double- D symbol. The double- D symbol will appear on the display. Push the button again to turn off Dolby(cid:3) B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape.
B NR*
: Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation. “DOLBY” and the
double D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
FM1·2
Push “FM1·2” to turn on the radio and
select the FM band. “FM1” or “FM2” will
appear on the display. This system allows
you to set twelve FM stations, two for
each button.
If the audio system is off, you can turn
on the radio by pushing “FM1·2”. Also,
push “FM1·2” to switch from cassette or
compact disc operation to radio operation.
PWR/VOL (Power/Volume)
Push “PWR/VOL” to turn the audio system
on and off. Turn “PWR/VOL” to adjust the
volume.
RAND (Random)
There are two random features—you can
either listen to the tracks on all the com-
pact discs in the magazine in random or-
der, or only
tracks on a
specific compact disc in random order.
listen
the
to
ECHO_U
the
random
turn off
Random playing for the tracks on a disc: Quickly push and release “RAND”. “RAND” will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To feature, push “RAND” again. Compact disc auto changer only— Random playing for all the tracks in the magazine: Push and hold “RAND” until you hear a beep. “ ·RAND” will appear on the dis- play and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the random fea- ture, push “RAND” again. RPT (Repeat) Cassette Player is playing. Push “RPT” while “RPT” will appear on the display. When the it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.
track ends,
track
the
Compact Disc Player There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” while the track is playing. “RPT” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Compact disc auto changer only— Repeating a disc: Push and hold “RPT” until you hear a beep. “ ·RPT” will appear on the dis- play. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back the disc and replay. This process will be continued until you push the button again to turn off the repeat feature.
to the top track of
2000 ECHO (OM52411U)
91
ECHO_U
SCAN
Radio
You can either scan all the frequencies on
a band or scan only the preset stations
for that band.
To scan the preset stations:
Push and hold “SCAN” until you hear a
beep. The radio will tune in the next pres-
et station up the band, stay there for 5
seconds, and then move to the next pre-
set station. To select a station, push
“SCAN” again.
To scan all the frequencies:
Quickly push and release “SCAN”. If you
hear a beep, you held the button too long,
and the radio will scan the preset sta-
tions. The radio will find the next station
up the station band, stay there for 5 se-
conds, and then scan again. To select a
station, push “SCAN” again.
Compact disc player
There are two scan features—you can ei-
ther scan the tracks on a specific disc or
scan the first tracks of all the discs in the
magazine.
Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning. Compact disc auto changer only— Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push “ the display and the player will perform the first track of the next disc. To select a disc, push the the player has scanned all the discs, it will stop scan- ning. SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “(cid:1)” or “(cid:2)” under the “SEEK”. Do this again to find another station.
the radio finds and the next station up or down the
·SCAN” will appear on
the seek mode,
“SCAN” again.
If
92
2000 ECHO (OM52411U)
Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display. If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. (cid:2) After tape
the beginning of
is the player will automatically
reached, start playing the same side.
the
ECHO_U
TUNE (Tuning) Your Toyota has an electronic tuning radio (ETR). Turn the knob clockwise to step up the frequency. Turn the knob counterclock- wise to step down the frequency.
2000 ECHO (OM52411U)
93
(cid:2) After the end of the tape is reached, the player will automatically reverse sides and start playing the other side. There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly.
the beginning of
to
ECHO_U
(cid:1)Type 2
Details of specific buttons, controls, and features are described in the alphabetical listing that follows.
SU17005
94
2000 ECHO (OM52411U)
to preset and
1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).
(Eject button) the cassette
Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a cassette or disc but you will not be able to reinsert it.
ECHO_U
(Program)
Push “ ” to select the other side of a cassette tape. The display indicates which ” indicates side is currently selected (“ top side, “ Auto- reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.
” indicates bottom side). feature: After
(Reverse/Fast forward buttons)
Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”. If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto- re- verse feature.
fast
the
the
Compact Disc Player If you want forward or reverse to fast through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation. CTRL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. For “CTRL appears on knob to suit your preference. The display will show the “BAS -5” to “BAS 5”.
tone adjustment, push / MODE” repeatedly until “BAS” the
the display. Then
to adjust
low- pitch
is used
range
turn
from
tone
2000 ECHO (OM52411U)
95
from
turn
range
to adjust
is also used
the display. Then
tone adjustment, push / MODE” repeatedly until “TRE” the
For high- pitch “CTRL appears on knob to suit your preference. The display will show the “TRE -5” to “TRE 5”. Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers. For front/rear adjustment, push “CTRL / MODE” repeatedly until “FAd” appears on the display. Then turn the knob to adjust the front/rear balance. The display will show “FAd- F7” to “FAd- R7”. For MODE” repeatedly until “BAL” appears on the display. Then turn the knob to adjust the left/right balance. The display will show “BAL- L7” to “BAL- R7”.
left/right adjustment, push “CTRL
range
range
from
from
the
the
ECHO_U
time you push “CD”,
CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each the system changes to the automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages. If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc.
inserted up- side down. Clean
loaded
inside
it the
is
96
2000 ECHO (OM52411U)
If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer. DISC (cid:2)(cid:1) Compact disc auto changer only— By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display. Dolby(cid:3) If you are listening to a tape that was recorded with Dolby(cid:3) B Noise Reduction, push the button marked with the double- D symbol. The double- D symbol will appear on the display. Push the button again to turn off Dolby(cid:3) B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape.
B NR*
: Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation. “DOLBY” and the
double D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
FM1·2
Push “FM1·2” to turn on the radio and
select the FM band. “FM1” or “FM2” will
appear on the display. This system allows
you to set twelve FM stations, two for
each button.
If the audio system is off, you can turn
on the radio by pushing “FM1·2”. Also,
push “FM1·2” to switch from cassette or
compact disc operation to radio operation.
PWR/VOL (Power/Volume)
Push “PWR/VOL” to turn the audio system
on and off. Turn “PWR/VOL” to adjust the
volume.
RAND (Random)
There are two random features—you can
either listen to the tracks on all the com-
pact discs in the magazine in random or-
der, or only
tracks on a
specific compact disc in random order.
listen
the
to
ECHO_U
the
random
turn off
Random playing for the tracks on a disc: Quickly push and release “RAND”. “RAND” will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To feature, push “RAND” again. Compact disc auto changer only— Random playing for all the tracks in the magazine: Push and hold “RAND” until you hear a beep. “ ·RAND” will appear on the dis- play and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the random fea- ture, push “RAND” again. RPT (Repeat) Cassette Player is playing. Push “RPT” while “RPT” will appear on the display. When the it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.
track ends,
track
the
Compact Disc Player There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” while the track is playing. “RPT” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Compact disc auto changer only— Repeating a disc: Push and hold “RPT” until you hear a beep. “ ·RPT” will appear on the dis- play. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back the disc and replay. This process will be continued until you push the button again to turn off the repeat feature.
to the top track of
2000 ECHO (OM52411U)
97
ECHO_U
SCAN
Radio
You can either scan all the frequencies on
a band or scan only the preset stations
for that band.
To scan the preset stations:
Push and hold “SCAN” until you hear a
beep. The radio will tune in the next pres-
et station up the band, stay there for 5
seconds, and then move to the next pre-
set station. To select a station, push
“SCAN” again.
To scan all the frequencies:
Quickly push and release “SCAN”. If you
hear a beep, you held the button too long,
and the radio will scan the preset sta-
tions. The radio will find the next station
up the station band, stay there for 5 se-
conds, and then scan again. To select a
station, push “SCAN” again.
Compact disc player
There are two scan features—you can ei-
ther scan the tracks on a specific disc or
scan the first tracks of all the discs in the
magazine.
Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning. Compact disc auto changer only— Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push “ the display and the player will perform the first track of the next disc. To select a disc, push the the player has scanned all the discs, it will stop scan- ning. SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “(cid:1)” or “(cid:2)” under the “SEEK”. Do this again to find another station.
the radio finds and the next station up or down the
·SCAN” will appear on
the seek mode,
“SCAN” again.
If
98
2000 ECHO (OM52411U)
Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display. If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. (cid:2) After tape
the beginning of
is the player will automatically
reached, start playing the same side.
the
ECHO_U
TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly. TUNE (Tuning) Your Toyota has an electronic tuning radio (ETR). Turn the knob clockwise to step up the frequency. Turn the knob counterclock- wise to step down the frequency.
the beginning of
to
(cid:2) After the end of the tape is reached, the player will automatically reverse sides and start playing the other side. There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player.
2000 ECHO (OM52411U)
99
ECHO_U
(cid:1)Type 3
Details of specific buttons, controls, and features are described in the alphabetical listing that follows.
SU17006
100
2000 ECHO (OM52411U)
ECHO_U
(Program)
Push “ ” to select the other side of a cassette tape. The display indicates which ” indicates side is currently selected (“ top side, “ Auto- reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.
” indicates bottom side). feature: After
(Reverse/Fast forward buttons)
Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”.
fast
the
the
to preset and
1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).
(Eject button) the cassette
Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a cassette or disc but you will not be able to reinsert it.
If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto- re- verse feature. Compact Disc Player If you want to fast forward or reverse through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation.
2000 ECHO (OM52411U)
101
ECHO_U
the
from
from
range
range
the knob
the knob
the display. Then
the display. Then
For front/rear adjustment, push “CONTROL / MODE” repeatedly until “FAd” appears on turn to adjust the front/rear balance. The display will show the “FAd- F7” to “FAd- R7”. For left/right adjustment, push “CONTROL / MODE” repeatedly until “BAL” appears on to turn adjust the left/right balance. The display will show “BAL- L7” to “BAL- R7”. CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each the system changes to the automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages.
time you push “CD”,
inserted up- side down. Clean
If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc. If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer.
loaded
inside
it the
is
the
tone
from
range
is used
low- pitch
to adjust
/ MODE”
CONTROL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. tone adjustment, push For “CONTROL repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show “BAS -5” to “BAS 5”. For middle- pitch tone adjustment, push “CONTROL / MODE” repeatedly until “MId” appears on the knob to suit your preference. The display will show the range from “MId - 5” to “MId 5”. tone adjustment, push For high- pitch “CONTROL repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show “TRE -5” to “TRE 5”. Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers.
the display. Then
is also used
/ MODE”
to adjust
range
turn
from
the
102
2000 ECHO (OM52411U)
ECHO_U
B NR*
DISC (cid:2)(cid:1)
Compact disc auto changer only—
By using this button, you can select a
disc you wish to listen to.
Push either side of the button until the
number of the disc you want to listen to
appears on the display.
Dolby(cid:3)
If you are listening to a tape that was
recorded with Dolby(cid:3) B Noise Reduction,
push the button marked with the double- D
symbol. The double- D symbol will appear
on the display. Push the button again to
turn off Dolby(cid:3) B NR.
The Dolby NR mode reduces tape noise
by about 10 dB. For best sound reproduc-
tion, play your tapes with this button on
or off according to the mode used for
recording the tape.
: Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation. “DOLBY” and the
double D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
FM1·2
Push “FM1·2” to turn on the radio and
select the FM band. “FM1” or “FM2” will
appear on the display. This system allows
you to set twelve FM stations, two for
each button.
If the audio system is off, you can turn on the radio by pushing “FM1·2”. Also, push “FM1·2” to switch from cassette or compact disc operation to radio operation. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order. Random playing for the tracks on a disc: Quickly push and release “ ” will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To turn off the random feature, push this button again.
listen
the
”. “
to
Compact disc auto changer only— Random playing for all the tracks in the magazine: Push and hold “ ” until you hear a ” will appear on the dis- beep. “ play and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the random fea- ture, push this button again. RPT (Repeat) Cassette Player Push “ ” while the track is playing. ” will appear on the display. When “ the track ends, it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.
2000 ECHO (OM52411U)
103
ECHO_U
Compact Disc Player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “ ” while the track is playing. “ ” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Compact disc auto changer only— Repeating a disc: Push and hold “ ” until you hear a ” will appear on the display. beep. “ The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. This process will be continued until you push the button again to turn off the re- peat feature.
SCAN
Radio
You can either scan all the frequencies on
a band or scan only the preset stations
for that band.
To scan the preset stations:
Push and hold “SCAN” until you hear a
beep. The radio will tune in the next pres-
et station up the band, stay there for 5
seconds, and then move to the next pre-
set station. To select a station, push
“SCAN” again.
To scan all the frequencies:
Quickly push and release “SCAN”. If you
hear a beep, you held the button too long,
and the radio will scan the preset sta-
tions. The radio will find the next station
up the station band, stay there for 5 se-
conds, and then scan again. To select a
station, push “SCAN” again.
104
2000 ECHO (OM52411U)
Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning. Compact disc auto changer only— Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push “ the display and the player will perform the first track of the next disc. To select a disc, push the the player has scanned all the discs, it will stop scan- ning.
·SCAN” will appear on
“SCAN” again.
If
ECHO_U
the seek mode,
the radio finds and the next station up or down the
SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “(cid:1)” or “(cid:2)” under the “SEEK”. Do this again to find another station. Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display.
If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. (cid:2) After tape
the beginning of
is the player will automatically
reached, start playing the same side.
the
(cid:2) After the end of the tape is reached, the player will automatically reverse sides and start playing the other side. There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion.
TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player. TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly. TUNE (Tuning) Your Toyota has an electronic tuning radio (ETR). Turn the knob clockwise to step up the frequency. Turn the knob counterclock- wise to step down the frequency.
the beginning of
to
2000 ECHO (OM52411U)
105
ECHO_U
Car audio system operating hints
NOTICE
To ensure the correct audio system operation: (cid:1) Be careful not to spill beverages
over the audio system.
(cid:1) Do not put anything other than a cassette tape or Compact Disc into the slot.
(cid:1) The use of cellular phone inside or near the vehicle may cause a noise from the speakers of the audio sys- tem which you are listening to. However, this does not indicate a malfunction.
RADIO RECEPTION Usually, a problem with radio reception does not mean there is a problem with your radio—it is just the normal result of conditions outside the vehicle. For example, nearby buildings and terrain can interfere with FM reception. Power lines or telephone wires can interfere with AM signals. And of course, radio signals have a limited range, and the farther you are from a station, the weaker its signal will be. In addition, reception conditions change constantly as your vehicle moves.
signals are
Here are some common reception prob-
lems that probably do not indicate a prob-
lem with your radio:
FM
Fading and drifting stations—Generally, the
effective range of FM is about 40 km (25
miles). Once outside this range, you may
notice fading and drifting, which increase
with the distance from the radio transmit-
ter. They are often accompanied by distor-
tion.
Multi- path—FM
reflective,
making it possible for two signals to reach
your antenna at the same time.
If this
happens, the signals will cancel each oth-
er out, causing a momentary
flutter or
loss of reception.
Static and
fluttering—These occur when
signals are blocked by buildings, trees, or
other large objects. Increasing the bass
level may reduce static and fluttering.
the FM signal you
Station swapping—If
are
interrupted or weak-
is
ened, and there is another strong station
nearby on the FM band, your radio may
tune in the second station until the origi-
nal signal can be picked up again.
listening to
they can
AM Fading—AM broadcasts are reflected by the upper atmosphere—especially at night. These reflected signals can interfere with those received directly from the radio sta- tion, causing the radio station to sound alternately strong and weak. Station interference—When a reflected sig- nal and a signal received directly from a radio station are very nearly the same frequency, interfere with each other, making it difficult to hear the broad- cast. Static—AM is easily affected by external sources of electrical noise, such as high tension power lines, lightening, or electri- cal motors. This results in static. CARING FOR YOUR CASSETTE PLAYER AND TAPES For high performance from your cassette player and tapes: Clean the tape head and other parts regu- larly. (cid:2) A dirty
tape head or tape path can decrease sound quality and tangle your cassette to clean them is by using a cleaning tape. (A wet type is recommended.)
tapes. The easiest way
106
2000 ECHO (OM52411U)
ECHO_U
(cid:2) If moisture gets into your compact disc player, you may not hear any sound even though your compact disc player appears the disc from the player and wait until it dries.
to be working. Remove
Use high- quality cassettes. (cid:2) Low- quality cassette tapes can cause many problems, including poor sound, inconsistent and constant auto- reversing. They can also get stuck or tangled in the cassette player.
playing
speed,
(cid:2) Do not use a cassette if it has been damaged or tangled or if its label is peeling off.
(cid:2) Do not leave a cassette in the player if you are not listening to it, especially if it is hot outside.
(cid:2) Store cassettes in their cases and out
of direct sunlight.
(cid:2) Avoid using cassettes with a total play-
ing time longer than 100 minutes (50
minutes per side). The tape used in
these cassettes is thin and could get
stuck or tangled in the cassette player.
CARING FOR YOUR COMPACT DISC PLAYER AND DISCS (cid:2) Use only compact discs
labeled as
shown.
(cid:2) Extremely high temperatures can keep your compact disc player from working. On hot days, use the air conditioning to cool the vehicle interior before you listen to a disc.
(cid:2) Bumpy roads or other vibrations may
make your compact disc player skip.
2000 ECHO (OM52411U)
107
ECHO_U
(cid:2) Your automatic changer or compact disc player cannot play special shaped compact discs as shown. Do not use them as the changer or player could be damaged.
(cid:2) Your automatic changer or compact disc player cannot play special shaped or low- quality compact discs such as shown here. Do not use them as the changer or player could be damaged. (cid:2) Handle compact discs carefully, espe- them. cially when you are them on the edge and do not Hold bend fingerprints them. Avoid getting on them, particularly on the shiny side. (cid:2) Dirt, scrapes, warping, pin holes, or the other disc damage could cause player to skip or to repeat a section of a track. (To see a pin hole, hold the disc up to the light.)
inserting
(cid:2) Remove discs from the compact disc
To clean a compact disc: Wipe it with a soft, lint- free cloth that has been damp- ened with water. Wipe in a straight line from the center to the edge of the disc (not in circles). Dry it with another soft, lint- free cloth. Do not use a conventional record cleaner or anti- static device.
CAUTION
Compact disc players use an invisible laser beam which could cause hazard- ous if directed outside the unit. Be sure to operate the player correctly as instructed.
radiation exposure
Z17035
them. Store
player when you are not listening to their plastic cases away from moisture, heat, and direct sunlight.
them
in
108
2000 ECHO (OM52411U)
ECHO_U
SECTION 1- 8
OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Controls Air flow selector settings Operating tips Instrument panel vents
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110
113
113
115
2000 ECHO (OM52411U)
109
ECHO_U
1. ”A/C” Button
2. Air Intake Selector
3. Air Flow Selector
4. Fan Speed Selector
5. Temperature Selector
Controls
SP18001
110
2000 ECHO (OM52411U)
ECHO_U
Fan speed selector Turn the knob to adjust the fan speed—to the right to increase, to the left to de- crease. Temperature selector Turn the knob to adjust the temperature— to the right to warm, to the left to cool.
Air flow selector Turn the knob to select the vents used for air flow. 1. Panel—Air
flows mainly
from
the
5. Windshield—Air flows mainly from the
windshield vents. Use with the air intake selector posi- tioned in Fresh.
For details about air flow selector settings, see the illustration after ”A/C” button. Turning the air flow control knob to wind- shield or floor/windshield position turns on the defroster- linked air conditioning. This is to clean up the front view more quickly. When the ”A/C” button is not pressed in, turning the air flow control knob to anoth- er position turns off the air conditioning.
instrument panel vents.
2. Bi- level—Air flows from both the floor vents and the instrument panel vents. 3. Floor—Air flows mainly from the floor
vents.
the
4. Floor/Windshield—Air
flows mainly floor vents and windshield
from vents. Use with the air intake selector posi- tioned in Fresh.
2000 ECHO (OM52411U)
111
ECHO_U
”A/C” button To turn on the air conditioning, press the ”A/C” button. The ”A/C” button indicator will come on. To turn the air conditioning off, press the button again.
Air intake selector Move the lever to select the air source. 1. Recirculate—Recirculates the air inside
the vehicle.
2. Fresh—Draws outside air into the sys-
tem.
112
2000 ECHO (OM52411U)
ECHO_U
Air flow selector settings
SU18004
Operating tips (cid:1) To cool off your Toyota after
it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.
(cid:1) Make sure the air intake grilles in front of the windshield are not blocked (by leaves or snow, for example).
(cid:1) On humid days, do not blow cold air on the windshield. The windshield could fog up because of the difference in air temperature on the inside and outside of the windshield.
(cid:1) Keep the area under the front seats clear to allow air to circulate through- out the vehicle.
(cid:1) On cold days, move the fan speed to ”HI” for a minute to help clear the in- take ducts of snow or moisture. This can reduce the amount of fogging on the windows.
2000 ECHO (OM52411U)
113
(cid:1) When driving on dusty roads, close all windows. If dust thrown up by the ve- hicle is still drawn into the vehicle after closing the windows, it is recommended that the air intake selector be set to FRESH and the fan speed selector to any setting except ”OFF”.
(cid:1) If following another vehicle on a dusty road, or driving in windy and dusty conditions, it is recommended that the air intake selector be temporarily set to RECIRCULATE, which will close off the outside passage and prevent outside air and dust from entering the vehicle interior.
ECHO_U
Heating For best results, set controls to:
Air conditioning For best results, set controls to:
Fan speed—Any setting except ”OFF” Temperature—Towards red zone Air intake—FRESH (outside air) Air flow—FLOOR Air conditioning—OFF
Fan speed—Any setting except ”OFF” Temperature—Towards blue zone Air intake—FRESH (outside air) Air flow—PANEL Air conditioning—ON
for a
few minutes. To keep
(cid:1) For quick heating, select recirculated air the windows from fogging, select fresh af- ter interior has been warmed.
the vehicle
(cid:1) Press the ”A/C” button on for dehumidi-
fied heating.
(cid:1) Choose floor/windshield air flow to heat the vehicle interior while defrosting or defogging the windshield.
(cid:1) For quick cooling, move the air intake selector to recirculate for a few min- utes.
Ventilation For best results, set controls to:
Fan speed—Any setting except ”OFF” Temperature—Towards blue zone Air intake—FRESH (outside air) Air flow—PANEL Air conditioning—OFF
114
2000 ECHO (OM52411U)
ECHO_U
Defogging The inside of the windshield For best results, set controls to:
Defrosting The outside of the windshield For best results, set controls to:
Instrument panel vents
Fan speed—Any setting except ”OFF” Temperature—Towards red zone to heat;
blue zone to cool Air intake—FRESH (outside air) Air flow—WINDSHIELD
turns on
Turning the air flow control knob to wind- shield position the defroster- linked air conditioning. This is to clean up the front view more quickly. When the ”A/C” button is not pressed in, turning the air flow control knob to a posi- tion other than windshield or floor/wind- shield turns off the air conditioning. (cid:1) On humid days, do not blow cold air on the windshield—the difference be- tween the outside and inside tempera- tures could make the fogging worse.
Fan speed—Any setting except ”OFF” Temperature—Towards red zone Air intake—FRESH (outside air) Air flow—WINDSHIELD
SY18004
turns on
Turning the air flow control knob to wind- shield position the defroster- linked air conditioning. This is to clean up the front view more quickly. When the ”A/C” button is not pressed in, turning the air flow control knob to a posi- tion other than windshield or floor/wind- shield turns off the air conditioning. (cid:1) To heat the vehicle interior while de- choose
windshield,
frosting floor/windshield air flow.
the
If air flow control is not satisfactory, check the instrument panel vents. The instrument panel vents may be opened or closed as shown.
2000 ECHO (OM52411U)
115
ECHO_U
116
2000 ECHO (OM52411U)
ECHO_U
SECTION 1- 8
OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Controls Air flow selector settings Operating tips Instrument panel vents
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
118
121
121
123
2000 ECHO (OM52411U)
117
ECHO_U
1. ”A/C” Button
2. Air Intake Selector
3. Air Flow Selector
4. Fan Speed Selector
5. Temperature Selector
Controls
SP18001
118
2000 ECHO (OM52411U)