2000 Toyota Celica Owners Manual

D Do not get under your vehicle with just the body jack supporting it. Al- ways use automotive jack stands or other solid supports.

loosen

D Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on, the electric cooling fans will automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.

D Use eye protection whenever you work on or under your vehicle where you may be exposed to flying or falling material, fluid spray, etc. D Used engine oil contains potentially harmful contaminants which may cause skin disorders such as in- flammation or skin cancer, so care should be taken to avoid prolonged and repeated contact with it. To re- move used engine oil from your skin, wash thoroughly with soap and water.

D Do not

leave used oil within the

reach of children.

D Dispose of used oil and filter only in a safe and acceptable manner. Do not dispose of used oil and fil- ter in household trash, in sewers or onto the ground. Call your dealer or a service station information concerning recycling or disposal.

for

2000 CELICA (OM20735U)

207

Celica_U

z Do not drive with the air cleaner filter removed, or excessive engine wear could result. Also backfiring could cause a fire in the engine compartment.

z Be careful not to scratch the glass

surface with the wiper frame.

z When closing

the engine hood, check to see that you have not for- gotten any tools, rags, etc.

NOTICE

z Remember that battery and ignition cables carry high currents or volt- ages. Be careful of accidentally causing a short circuit.

z Add only demineralized or distilled water to fill the radiator. And if you spill some of the coolant, be sure to wash it off with water to prevent it from damaging the parts or paint. z Do not allow dirt or anything else to fall through the spark plug holes. z Do not pry the outer electrode of a spark plug against the center elec- trode.

z Use only spark plugs of the speci- fied type. Using other types will cause engine damage, loss of per- formance or radio noise.

z Do not reuse iridium−tipped spark

plugs by cleaning or regapping.

z Do not overfill automatic transmis- transmission

fluid, or

the

sion could be damaged.

208

2000 CELICA (OM20735U)

Parts and tools Here is a list of parts and tools you will need on performing do−it−yourself mainte- nance. Remember all Toyota parts are de- signed in metric sizes, so your tools must be metric. Checking the engine oil level Parts (if level is low): D Engine API

SJ, “Energy−Conserving” ILSAC multigrade having viscosity proper for your climate

grade or

oil

Tools: D Rag or paper towel D Funnel (only for adding oil) Checking the engine coolant level Parts (if level is low): D “TOYOTA Long Life Coolant” or equiva-

lent See Section 7−2 for details about cool- ant type selection.

D Demineralized or distilled water Tools: D Funnel (only for adding coolant) Checking brake fluid Parts (if level is low): D SAE J1703 or FMVSS No.116 DOT 3

brake fluid

Celica_U

Tools: D Funnel Replacing light bulbs Parts: D Bulb with same number and wattage charts in in Section

(See light bulbs—”

rating as original “Replacing 7−3.)

Tools: D Screwdriver

fluid

terminal

Tools: D Rag or paper towel D Funnel (only for adding fluid) Checking power steering fluid Parts (if level is low): D Automatic

transmission

DEXRONrII or III

Tools: D Rag or paper towel D Funnel (only for adding fluid) Checking battery condition Tools: D Warm water D Baking soda D Grease D Conventional wrench

(for

clamp bolts)

Checking and replacing fuses Parts (if replacement is necessary): D Fuse with same amperage rating as

original

Adding washer fluid Parts: D Water D Washer fluid containing antifreeze

(for winter use)

2000 CELICA (OM20735U)

209

Celica_U

210

2000 CELICA (OM20735U)

Celica_U

SECTION 7− 2

DO−IT−YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level Checking the engine coolant level Checking brake fluid Checking power steering fluid Checking tire pressure Checking and replacing tires Rotating tires Installing snow tires and chains Replacing wheels Aluminum wheel precautions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

212
213
214
215
216
217
218
220
221
221

2000 CELICA (OM20735U)

211

Celica_U

CAUTION

Be careful not to touch the hot ex- haust manifold.

If the oil level is below or only slightly above the low level, add engine oil of the same type as already in the engine. Remove the oil filler cap and add engine oil in small quantities at a time, checking the dipstick. The approximate quantity of oil needed to fill between the low level and the full level on the dipstick is indicated below for ref- erence. When the level reaches within the correct range, install the filler cap hand−tight. Oil quantity, L (qt., lmp. qt.):

2.7 (3.0, 2.4)

NOTICE

z Avoid overfilling, or

the engine

could be damaged.

z Check the oil level on the dipstick

once again after adding the oil.

ENGINE OIL SELECTION Use API grade SJ, “Energy−Conserving” or ILSAC multigrade engine oil. Recommended viscosity (SAE):

for good

SAE 5W−30 is the best choice for your vehicle, fuel economy, and good starting in cold weather. If you use SAE 10W−30 engine oil in extremely low temperatures, the engine may become difficult to start, so SAE 5W−30 engine oil is recommended.

Checking the engine oil level

Low level

Full level

Add oil

O.K.

Too full

With the engine at operating tempera- ture and turned off, check the oil level on the dipstick. 1. To get a

the vehicle should be on a level spot. After turning off the engine, wait a few minutes for the oil to drain back into the bottom of the engine.

reading,

true

2. Pull out the dipstick, and wipe it clean

with a rag.

3. Reinsert the dipstick—push it in as far as it will go, or the reading will not be correct.

4. Pull the dipstick out and look at the oil

level on the end.

212

2000 CELICA (OM20735U)

Celica_U

Oil identification marks Either or both API registered marks are added to some oil containers to help you select the oil you should use. The API Service Symbol is located any- where on the outside of the container. The top portion of the label shows the oil quality by API (American Petroleum Institute) designations such as SJ. The center portion of the label shows the SAE viscosity grade such as SAE 5W−30. “Energy−Conserving” shown in the lower portion, has fuel−saving capabilities. The ILSAC (International Lubricant Stan- dardization and Approval Committee) Certi- fication Mark is displayed on the front of the container.

indicates

that

the

oil

“Replacing

Checking the engine coolant level Look at the see−through coolant reser- voir when the engine is cold. The cool- ant level is satisfactory if it is between the “FULL” and “LOW” lines on the reservoir. If the level is low, add ethyl- ene−glycol type coolant for a proper corrosion protection of aluminum com- ponents. Before adding coolant, remove the cover. For instructions, see light bulbs—” in Section 7−3. The coolant level in the reservoir will vary with engine temperature. However, if the level is on or below the “LOW” line, add coolant. Bring the level up to the “FULL” line. type coolant Always use ethylene−glycol for a proper corrosion protection of alumi- num components. See information in the next column. If the coolant level drops within a short time after replenishing, there may be a leak the radiator, hoses, drain cock and water pump. If you can find no leak, have your Toyota dealer test the cap pressure and check for leaks in the cooling system.

the system. Visually check

in

2000 CELICA (OM20735U)

213

API service symbol

ILSAC certification mark

Celica_U

We recommend to use 50% solution for your Toyota, to provide protection down to about −35_C (−31_F). When it is extreme- ly cold, to about −50_C (−58_F), 60% solution is rec- ommended. Do not use more than 70% solution for better coolant performance.

to provide protection down

NOTICE

Do not use alcohol type antifreeze or plain water alone.

Checking brake fluid

reservoir. The

To check the fluid level, simply look at the see−through level should be between the “MAX” and “MIN” lines on the reservoir. It is normal for the brake fluid level to go down slightly as the brake pads wear. So be sure to keep the reservoir filled. If the reservoir needs frequent refilling, it may indicate a serious mechanical prob- lem.

CAUTION

To prevent burning yourself, do not remove the coolant reservoir cap or air release valve when the engine is hot.

Coolant type selection Use of improper coolants may damage your engine cooling system. Your coolant must contain ethylene−glycol type coolant for a proper corrosion protection of your engine that contains aluminum compo- nents. Use “TOYOTA Long Life Coolant” or equivalent. In addition to preventing freezing and sub- sequent damage to the engine, this type of coolant will also prevent corrosion. Fur- ther supplemental inhibitors or additives are neither needed nor recommended. Read the coolant container for information on freeze protection. Follow the manufac- turer’s directions to mix with plain water (preferably demineralized water or distilled water). The total capacity of the cooling system is given in Section 8.

for how much

214

2000 CELICA (OM20735U)

If the level is low, add SAE J1703 or FMVSS No.116 DOT 3 brake fluid to the brake reservoir. Remove and replace the reservoir cap by hand. Fill the brake fluid to the dotted line. This brings the fluid to the correct level when you put the cap back on. Use only newly opened brake fluid. Once opened, brake fluid absorbs moisture from the air, and excess moisture can cause a dangerous loss of braking.

CAUTION

Take care when filling the reservoir because brake fluid can harm your eyes and damage painted surfaces. If fluid gets in your eyes, flush your eyes with clean water.

NOTICE

If you spill the fluid, be sure to wash it off with water to prevent it from damaging the parts or paint.

Celica_U

Checking power steering fluid

If hot O.K.

Close

If hot add

Open

If cold O.K.

If cold add

Check the fluid level through the reser- voir. If necessary, add automatic trans- mission fluid DEXRONRII or III. If the vehicle has been driven around 80
km/h (50 mph) for 20 minutes (a little more in frigid temperatures), the fluid is hot (60°C—80°C or 140°F—175°F). You may also check the level when the fluid is temperature, 10°C—30°C or 50°F—85°F) if the engine has not been run for about five hours.

(about

room

cold

Clean all dirt from outside of the reservoir tank and look at the fluid level. If the fluid is cold, the level should be in the “COLD” range. Similarly, if it is hot, the fluid level should be in the “HOT” range. If the level is at the low side of either range, add fluid DEXRONRII automatic or III to bring the level within the range. To remove the reservoir cap, turn it coun- terclockwise and it, turn it clockwise. After replacing the reser- voir cap, visually check the steering box case, vane pump and hose connections for leaks or damage.

lift up. To reinstall

transmission

CAUTION

The reservoir tank may be hot so be careful not to burn yourself.

NOTICE

Avoid overfilling, or the power steer- ing could be damaged.

2000 CELICA (OM20735U)

215

Celica_U

Checking tire pressure

Keep your tire pressures at the proper level. The recommended cold tire pressures, tire size and the vehicle capacity weight are given in Section 8. They are also on the tire pressure label as shown. You should check the tire pressures every two weeks, or at least once a month. And do not forget the spare!

the

results

tire pressure

tire pressure

is excessively

Incorrect tire pressure can reduce tire life and make your vehicle less safe to drive. Low in excessive wear, poor handling, reduced fuel econo- my, and the possibility of blowouts from overheated tires. Also, low tire pressure can cause poor sealing of the tire bead. If low, there is the possibility of wheel deforma- tion and/or tire separation. High tire pressure produces a harsh ride, handling problems, excessive wear at the center of the tire tread, and a greater possibility of tire damage from road haz- ards. If a tire frequently needs refilling, have it checked by your Toyota dealer. The following instructions for checking tire pressure should be observed: D The pressure should be checked only when the tires are cold. If your ve- hicle has been packed for at least 3
hours and has not been driven for more than 1.5 km or 1 mile since, you will get an accurate cold tire pressure reading.

D Always use a tire pressure gauge. The appearance of a tire can be mis- leading. Besides, that are even just a few pounds off can degrade handling and ride.

tire pressures

D Take special care when adding air to the compact spare tire. The smaller tire size can gain pressure very quick- ly. Add compressed air in small quanti- ties and check the pressure often until it reaches the specified pressure.

D Do not bleed or reduce tire pressure after driving. It is normal for the tire pressure to be higher after driving.

D Never exceed

the vehicle capacity weight. The passenger and luggage weight should be located so that the vehicle is balanced.

D Be sure to reinstall the tire inflation valve caps. Without the valve caps, dirt or moisture could get into the valve core and cause air leakage. If the caps have been lost, have new ones put on as soon as possible.

216

2000 CELICA (OM20735U)

Celica_U

Checking and replacing tires

Tread wear indicator

CHECKING YOUR TIRES Check the tire tread for the tread wear indicators. If the indicators show, re- place the tires. The tires on your Toyota have built−in tread wear indicators to help you know when the tires need replacement. When the tread depth wears to 1.6 mm (0.06
in.) or less, the indicators will appear. If you can see the indicators in two or more adjacent grooves, the tire should be re- placed. The lower the tread, the higher the risk of skidding. The effectiveness of snow tires is lost if the tread wears down below 4 mm (0.16 in.).

Check the tires regularly for damage such as cuts, splits and cracks. If any damage is found, consult with a techni- cian and have the tire repaired or re- placed. Even if the damage does not appear seri- ous, a qualified technician should examine the damage. Objects which have pene- trated the tire may have caused internal damage. Any tires which are over 6 years old must be checked by a qualified techni- cian even if damage is not obvious. Tires deteriorate with age even have never or seldom been used. This also applies to the spare tire and tires stored for future use. REPLACING YOUR TIRES When replacing a tire, use only the same size and construction as original- ly installed and with the same or great- er load capacity. Using any other size or type of tire may seriously affect handling, ride, speedome- ter/odometer calibration, ground clearance, and clearance between the body and tires or snow chains.

they

if

CAUTION

D Do not mix radial, bias belted, or bias−ply tires on your vehicle. It can cause dangerous handling char- acteristics, resulting in loss of con- trol.

D Do not use tires or wheels other recom-

the manufacturer’s

than mended size.

tire

Toyota recommends all four tires, or at least both front or rear tires be re- placed as a set. See “If you have a flat tire—” in Section 4 for tire change procedure. When a is replaced, should always be balanced. An unbalanced wheel may affect vehicle handling and tire life. Wheels can get out of balance with regular use and should therefore be balanced occasionally. When replacing a tubeless tire, the air valve should also be replaced with a new one.

the wheel

2000 CELICA (OM20735U)

217

Celica_U

Rotating tires

Turning direction

If a turning indicator is marked on your tires, you have uni−directional tires. Be- fore rotating, check whether your tires are uni−directional before rotating them. Using tires on the wrong side of the vehicle will impair tire performance. See the following instructions for how to rotate your tires correctly.

Turning direction indicator (type A)

With uni−directional tires

Turning direction

Turning direction indicator (type B)

218

2000 CELICA (OM20735U)

Celica_U

CAUTION

Do not include a compact spare tire when rotating the tires. It is designed for temporary use only.

Without uni−directional tires (with a spare tire of the same wheel type as the installed tires)

Without uni−directional tires (with a spare tire of different wheel type from the installed tires)

To equalize tire wear and help extend tire life, Toyota recommends that you rotate your tires approximately every 12000 km (7500 miles). However, the most appropriate timing for tire rotation may vary according to your driving hab- its and road surface conditions. See “If you have a flat tire—” in Section 4 for tire change procedure. When for uneven tires, check wear and damage. Abnormal wear is usu- ally caused by incorrect tire pressure, im- proper wheel alignment, out−of−balance wheels, or severe braking.

rotating

2000 CELICA (OM20735U)

219

Celica_U

CAUTION

D Do not drive with the snow tires

incorrectly inflated.

D Never drive over 120 km/h (75 mph)

with any type of snow tires.

TIRE CHAIN SELECTION Use the tire chains of correct size and type. Use SAE Class “S” type radial tire chains except radial cable chains or V−bar type chains. Regulations regarding the use of tire chains vary according to location or type of road, so always check them before installing chains. CHAIN INSTALLATION Install the chains on the front tires as tightly as possible. Do not use tire tires. Retighten chains on chains after km (1/4—1/2 mile). When installing chains on your tires, care- fully follow the instructions of the chain manufacturer.

rear driving

0.5—1.0

the

Installing snow tires and chains WHEN TO USE SNOW TIRES OR CHAINS Snow tires or chains are recommended when driving on snow or ice. On wet or dry roads, conventional tires provide better traction than snow tires. SNOW TIRE SELECTION If you need snow tires, select the same size, construction and load capacity as the original tires on your Toyota. Do not use tires other than those men- tioned above. Do not install studded tires without first checking local regulations for possible restrictions. SNOW TIRE INSTALLATION Snow tires should be installed on all wheels. Installing snow tires on the front wheels only can lead to an excessive difference in road grip capability between the front and rear tires which could cause loss of vehicle control. When storing removed tires, you should store them in a cool dry place. Mark the direction of rotation and be sure to install them in the same direction when replacing.

220

2000 CELICA (OM20735U)

If wheel covers are used, they will be scratched by the chain band, so remove the covers before putting on the chains.

CAUTION

D Do not exceed 50 km/h (30 mph) or recom- is

the chain manufacturer’s mended speed lower.

limit, whichever

D Drive carefully avoiding bumps, holes, and sharp turns, which may cause the vehicle to bounce.

D Avoid sharp turns or locked−wheel braking, as use of chains may ad- versely affect vehicle handling.

NOTICE

Do not attempt to use a tire chain on the compact spare tire, as it may re- sult in damage to the vehicle as well as the tire.

Celica_U

Replacement with used wheels is not rec- ommended as they may have been sub- jected to rough treatment or high mileage and could fail without warning. Also, bent wheels which have been straightened may have structural damage and therefore should not be used. Never use an inner tube in a leaking wheel which is designed for a tubeless tire.

Replacing wheels WHEN TO REPLACE YOUR WHEELS If you have wheel damage such as bending, cracks or heavy corrosion, the wheel should be replaced. If you fail to replace damaged wheels, the tire may slip off the wheel or cause loss of handling control. WHEEL SELECTION When replacing wheels, care should be taken to ensure that the wheels are re- placed by ones with the same load ca- pacity, diameter, rim width, and offset. This must be observed on compact spare tires, too. Correct replacement wheels are available at your Toyota dealer. A wheel of a different size or type may adversely affect handling, wheel and bear- ing life, brake cooling, speedometer/odom- eter calibration, stopping ability, headlight aim, bumper height, vehicle ground clear- ance, and tire or snow chain clearance to the body and chassis.

Aluminum wheel precautions D After driving your vehicle the first 1600
km (1000 miles), check that the wheel nuts are tight. repaired, or D If you have changed your the wheel nuts are still tight after driving 1600 km (1000 miles).

rotated, tires, check

that

D When using tire chains, be careful not

to damage the aluminum wheels.

D Use only the Toyota wheel nuts and for your aluminum

wrench designed wheels.

D When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer.

D As with any wheel, periodically check your aluminum wheels for damage. If damaged, replace immediately.

2000 CELICA (OM20735U)

221

Celica_U

222

2000 CELICA (OM20735U)

Celica_U

SECTION 7− 3

DO−IT−YOURSELF MAINTENANCE Electrical components

2000 CELICA (OM20735U)

223

Celica_U

Checking battery condition

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

229

224

2000 CELICA (OM20735U)

Celica_U

Battery recharging precautions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

230

2000 CELICA (OM20735U)

225

Celica_U

Checking and replacing fuses

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

231

226

2000 CELICA (OM20735U)

Celica_U

Adding washer fluid

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

232

2000 CELICA (OM20735U)

227

Celica_U

Replacing light bulbs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

233

228

2000 CELICA (OM20735U)

Celica_U

D If electrolyte gets on your skin, thoroughly wash the contact area. If you feel pain or burning, get medi- cal attention immediately.

D If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediate- ly take off the exposed clothing and follow the procedure above, if nec- essary.

D If you accidentally swallow electro- lyte, drink a large quantity of water or milk. Follow with milk of magne- sia, beaten raw egg or vegetable oil. Then go immediately for emer- gency help.

Checking battery condition— —Precautions

CAUTION

BATTERY PRECAUTIONS The battery produces flammable and explosive hydrogen gas. D Do not cause a spark from the bat-

tery with tools.

D Do not smoke or light a match near

the battery.

The electrolyte contains poisonous and corrosive sulfuric acid. D Avoid contact with eyes, skin or

clothes.

D Never ingest electrolyte. D Wear protective safety glasses when

working near the battery.

D Keep children away from the bat-

tery.

EMERGENCY MEASURES D If electrolyte gets

in your eyes, flush your eyes with clean water immediately immediate medical attention. If possible, con- tinue to apply water with a sponge or cloth while en route to the medi- cal office.

and get

—Checking battery exterior

Terminals

Ground cable

Hold−down clamp

Check the battery for corroded or loose terminal connections, cracks, or loose hold−down clamp. a. If the battery is corroded, wash it off with a solution of warm water and bak- ing soda. Coat the outside of the termi- nals with grease to prevent further cor- rosion.

b. If the terminal connections are loose, their clamp nuts—but do not

tighten overtighten.

c. Tighten

the hold−down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.

2000 CELICA (OM20735U)

229

Celica_U

—Checking battery fluid

NOTICE

Type A

z Be sure the engine and all accesso- ries are off before performing main- tenance.

z When checking the battery, remove the ground cable from the negative terminal (“−” mark) first and rein- stall it last.

z Be careful not to cause a short cir-

cuit with tools.

z Take care no solution gets into the

battery when washing it.

Green

Dark

Clear or light yellow

Type B

Blue

White

Red

CHECKING BY HYDROMETER Check hydrometer color.

the battery condition by

the

Hydrometer color

Type A

GREEN

Type B

BLUE

DARK

WHITE

CLEAR or

LIGHT

YELLOW

RED

Condition

Good

Charging necessary. Have battery checked by your Toyota dealer. Have battery checked by your Toyota dealer.

230

2000 CELICA (OM20735U)

Battery recharging precautions During recharging, the battery is pro- ducing hydrogen gas. Therefore, before recharging: 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.

2. Be sure the power switch on the re- charger the charger cables to the battery and when disconnecting them.

is off when connecting

CAUTION

D Always charge the battery in an un- confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventila- tion.

D Only do a slow charge (5 A or less). Charging at a quicker rate is dangerous. The battery may ex- plode, causing personal injuries.

NOTICE

Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.

Celica_U

Checking and replacing fuses

Good

Blown

Good

Blown

Type A

Type C

Good

Blown

Good

Blown

Type B

Type D

2000 CELICA (OM20735U)

If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced. See “Fuse locations” in Section 7−1 for locations of the fuses. Turn the ignition switch and inoperative component off. Pull a suspected fuse straight out and check it. Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse. See Section 8 of this manual for the functions controlled by each circuit. Type A fuses can be pulled out by the pull−out tool. The location of the pull−out tool is shown in the illustration.

231

Celica_U

Adding washer fluid

CAUTION

Never use a fuse with a higher am- perage rating, or any other object, in place of a fuse. This may cause ex- tensive damage and possibly a fire.

If any washer does not work, the wash- er tank may be empty. Check the wash- er fluid level on the level gauge. If the washer fluid level is below “LOW”, add washer fluid. You may use plain water as washer fluid. in cold areas where tempera- However, tures freezing point, use fluid containing antifreeze. This washer product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

range below

If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good. If the fuse has blown, push a new fuse into the clip. Only install a fuse with the amperage rat- ing designated on the fuse box lid. If you do not have a spare fuse, in an emergency you can pull out the “RADIO”, “CIG” or “HTR” fuse, which may be dis- pensable for normal driving, and use it if its amperage rating is the same. If you cannot use one of the same amper- age, use one that is lower, but as close as possible to the rating. If the amperage is fuse might blow out again but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clip. It is a good idea to purchase a set of spare fuses and keep them in your ve- hicle for emergencies. If fuse immediately blows out, there is a problem with the electrical sys- tem. Have your Toyota dealer correct it as soon as possible.

that specified,

the new

lower

than

the

232

2000 CELICA (OM20735U)

NOTICE

Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.

Celica_U

following

illustrations show how

Replacing light bulbs— The to gain access to the bulbs. When replacing a bulb, make sure the ignition switch and light switch are off. Use bulbs with the wattage ratings given in the table.

CAUTION

Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.

NOTICE

Only use a bulb of the listed type.

Light bulbs

Bulb No.

W Type

Front turn signal lights

Front side marker lights

Rear turn signal lights

Stop and tail lights

Back−up lights

License plate lights

Interior light (with moon roof)

— 21

— 5

— 21

— 21/5
— 18
— 5

— 10

Interior lights (without moon roof) — 8
— 1.2
Glove box light

Light bulbs

Bulb No.

W Type

Luggage compartment light

— 5

Headlights

(low beam)

Headlights

(high beam)

Front fog light

Parking lights

— 55

9005

65

— 55
— 5

A: H7 halogen bulbs B: HB3 halogen bulbs C: H3 halogen bulbs D: Wedge base bulbs E: Single end bulbs F: Double end bulbs

2000 CELICA (OM20735U)

233

—Headlights (low beam)

Celica_U

1. Open the hood. RIGHT SIDE HEADLIGHT: Remove the clips and take out the cover. In doing so, remove the washer hose from the notch on the cover. Remove and install shown in the following illustrations.

the cover clips as

Removing clip

Installing clip

234

2000 CELICA (OM20735U)

Celica_U

2. Unplug the connector. Remove the

rubber cover.

If the connector is tight, wiggle it.

3. Release

the bulb retaining spring and remove the bulb along with the socket. Install a new bulb into the socket and return the bulb retaining spring to its original position.

To install a bulb, align the tabs of the bulb with the cutout of the mounting hole.

4. Install

the rubber cover with

the “TOP” mark upward, and snuggle on the boss. Insert the connector.

Make sure the rubber cover fits snugly on the connector and the headlight body. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.

2000 CELICA (OM20735U)

235

Celica_U

—Headlights (high beam)

1. Open the hood. RIGHT SIDE HEADLIGHT: Remove the clips and take out the cover. In doing so, remove the washer hose from the notch on the cover. Remove and install shown in the following illustrations.

the cover clips as

5. RIGHT SIDE HEADLIGHT: Install the

cover.

NOTICE

Always notch the washer hose before fastening it when installing the cover. This prevents washer hose damage.

236

2000 CELICA (OM20735U)

Celica_U

Removing clip

2. Turn the bulb base counterclockwise

and remove it.

3. Pull the bulb out of the bulb base

and install a new bulb.

If the connector is tight, wiggle it.

Installing clip

2000 CELICA (OM20735U)

237

Celica_U

—Front fog and front side marker lights If either the left or right front fog or front side marker lights burns out, con- tact your Toyota dealer.

NOTICE

Do not try to replace the front fog or front side marker light bulbs by your- self. You may damage the vehicle.

4. Insert the bulb base into the mount-

ing hole by turning it clockwise.

Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.

5. RIGHT SIDE HEADLIGHT: Install the

cover.

NOTICE

Always notch the washer hose before fastening it when installing the cover. This prevents washer hose damage.

238

2000 CELICA (OM20735U)

—Parking lights

Celica_U

RIGHT SIDE PARKING LIGHT: Remove and install the clips as shown in the following illustrations.

NOTICE

Always notch the washer hose before fastening it when installing the cover. This prevents washer hose damage.

Removing clip

Installing clip

2000 CELICA (OM20735U)

239

Celica_U

—Front turn signal lights

RIGHT SIDE FRONT TURN SIGNAL LIGHT: Remove and install the clips as shown in the following illustrations.

NOTICE

Always notch the washer hose before fastening it when installing the cover. This prevents washer hose damage.

240

2000 CELICA (OM20735U)

Celica_U

—Rear turn signal, stop and tail, and back−up lights

Removing clip

Remove the cover.

Installing clip

2000 CELICA (OM20735U)

241

Celica_U

—License plate lights

a: Stop and tail light b: Back−up light c: Rear turn signal light

Use a Phillips−head screwdriver.

242

2000 CELICA (OM20735U)

Remove the cover.

Celica_U

2000 CELICA (OM20735U)

243

Celica_U

SECTION 8

SPECIFICATIONS Dimensions and weight Engine Fuel Service specifications Tires Fuses

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

245
245
245
246
248
249

244

2000 CELICA (OM20735U)

Dimensions and weight Overall length mm (in.) Overall width mm (in.) Overall height mm (in.) mm (in.) Wheelbase mm (in.) Front tread Rear tread mm (in.) Vehicle capacity weight (occupants + luggage) kg (lb.)

∗:Unladen vehicle

4330 (170.5) 1735
(68.3) (51.8)∗ 1305
2600 (102.4) (58.7) 1490
1480
(58.3)

329

(725)

Celica_U

Engine Model:

1ZZ−FE and 2ZZ−GE

Type:

4 cylinder in line, 4 cycle, gasoline

Bore and stroke, mm (in.):

1ZZ−FE engine

79.0 91.5 (3.11 3.60)

2ZZ−GE engine

82.0 85.0 (3.23 3.35)

Displacement, cm3 (cu. in.):

1ZZ−FE engine 2ZZ−GE engine

1794 (109.5) 1796 (109.6)

Fuel Fuel type:

1ZZ−FE engine

Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher

2ZZ−GE engine

Select premium unleaded gasoline with an Octane Rating of 95 (Research Oc- tane Number 96) or higher for opti- mum engine performance

Fuel tank capacity, L (gal., Imp. gal.):

55 (14.5, 12.1)

2000 CELICA (OM20735U)

245

Service specifications ENGINE Valve clearance (engine cold), mm (in.):

1ZZ−FE engine

Intake Exhaust

0.15—0.25 (0.006—0.010) 0.25—0.35 (0.010—0.014)

2ZZ−GE engine (on a roller side)

Intake Exhaust

0.10—0.16 (0.004—0.006) 0.24—0.30 (0.010—0.012)

Spark plug type: 1ZZ−FE engine

DENSO NGK

SK16R11
IFR5A11

2ZZ−GE engine

DENSO NGK

SK20R11
IFR6A11
Spark plug gap, mm (in.):

1.1 (0.043)

Celica_U

ENGINE LUBRICATION Oil capacity (drain and refill), L (qt., Imp. qt.): 1ZZ−FE engine

With filter Without filter 2ZZ−GE engine

With filter Without filter

3.7 (3.9, 3.3) 3.5 (3.7, 3.1)

4.4 (4.8, 4.0) 4.2 (4.6, 3.8)

Oil grade:

API grade SJ, “Energy−Conserving” or ILSAC multigrade engine oil is recom- mended.

Recommended oil viscosity (SAE):

COOLING SYSTEM Total capacity, L (qt., Imp. qt.):

1ZZ−FE engine

Manual transaxle Automatic transaxle

2ZZ−GE engine

Manual transaxle Automatic transaxle

Coolant type:

5.7 (6.0, 5.0) 5.6 (5.9, 4.9)

5.9 (6.2, 5.2) 5.8 (6.1, 5.1)

“TOYOTA Long Life Coolant” or equiva- lent With ethylene−glycol type coolant for a proper corrosion protection of aluminum components Do not use alcohol type antifreeze or plain water alone.

BATTERY Open voltage∗ at 20°C (68°F):

12.6—12.8 V 12.2—12.4 V 11.8—12.0 V

Fully charged Half charged Discharged

∗: Voltage that is checked 20 minutes af- ter the key is removed with all the lights turned off Charging rates:

246

2000 CELICA (OM20735U)

5 A max.

Celica_U

CLUTCH Pedal free play, mm (in.):

5—15 (0.2—0.6)

Fluid type:

SAE J1703 or FMVSS No.116 DOT 3

MANUAL TRANSAXLE Oil capacity, L (qt., Imp. qt.):

1ZZ−FE engine 1.9 (2.0, 1.7) 2ZZ−GE engine 2.3 (2.4 2.0)

Oil type:

Gear oil API GL−4 or GL−5

Recommended oil viscosity:

SAE 75W−90

AUTOMATIC TRANSAXLE Fluid capacity (drain and refill), L (qt., Imp. qt.): 1ZZ−FE engine

Up to 2.1 (2.2, 1.8)

2ZZ−GE engine

Up to 4.0 (4.2, 3.5)

Fluid type:

Automatic transmission fluid Type T−IV Change automatic transmission fluid only as necessary.

in

listed

Generally, it is necessary to change auto- matic transmission fluid only if your ve- hicle is driven under one of the Special Operating Conditions your “Scheduled Maintenance Guide” or “Own- er’s Manual Supplement”. When changing the automatic transmission fluid, use only Toyota Genuine ATF Type T−IV (ATF in assuring optimum JWS3309) transaxle performance. Notice: Using automatic transmission fluid other than Toyota Genuine ATF Type T−IV may cause deterioration in shift quality, locking up of your trans- mission accompanied by vibration, and ultimately damage the automatic trans- mission of your vehicle.

to aid

BRAKES Minimum pedal clearance when depressed with the pressure of 490 N (50 kgf, 110
lbf) with the engine running, mm (in.):

85 (3.4)

Pedal free play, mm (in.):

1—6 (0.04—0.24)

Pad wear limit, mm (in.):

1.0 (0.04)

Lining wear limit, mm (in.):

1.0 (0.04)

Parking brake adjustment when pulled with the force of 196 N (20 kgf, 44 lbf):

5—8 clicks

Fluid type:

SAE J1703 or FMVSS No.116 DOT 3

STEERING Wheel free play:

Less than 30 mm (1.2 in.)

Power steering fluid type:

Automatic transmission fluid DEXRON®II or III

2000 CELICA (OM20735U)

247

Celica_U

Tires Tire size and pressure: Except spare tire

Model

Tire size

1ZZ−FE engine

195/60R15 88H

P195/60R15 87H

205/55R15 87V

2ZZ−GE engine

P205/55R15 87V

205/50R16 87V

Tire pressure

kPa (kgf/cm2 or bar, psi)

Front

210 (2.1, 29)

210 (2.1, 29)

220 (2.2, 32)

220 (2.2, 32)

220 (2.2, 32)

Rear

210 (2.1, 29)

210 (2.1, 29)

220 (2.2, 32)

220 (2.2, 32)

220 (2.2, 32)

Spare tire

U.S.A

Canada

Tire size

T125/70D16

Tire pressure kPa (kgf/cm2 or bar, psi)

420 (4.2, 60)

Same as original tire

Wheel nut torque, N·m (kgf·m, ft·Ibf):

103 (10.5, 76)

Wheel size

15 6 1/2JJ

15 6 1/2JJ

15 6 1/2JJ

15 6 1/2JJ

16 6 1/2JJ

Wheel size

16 4T

NOTE: For a complete information on tires (e.g. replacing tires or replacing wheels), see “Checking tire pressure” through “Aluminum

wheel precautions” in Section 7−2.

248

2000 CELICA (OM20735U)

Celica_U

Fuses

Engine compartment

Engine compartment

Instrument panel

Fuses (type A) 1. HEAD LH LWR 10 A: Left−hand head-

light (low beam)

2. ABS NO.2 25 A: Anti−lock brake sys-

tem

3. HEAD RH UPR 20 A: Right−hand

headlight (high beam)

4. DRL NO.3 7.5 A: Daytime running light

system

5. HEAD RH LWR 10 A: Right−hand

headlight (low beam)

6. HEAD LH UPR 10 A: Left−hand head-

light (high beam)

7. IG2 15 A: Starting system, multiport injection system/sequential multi-

fuel port fuel injection system

8. HAZ 10 A: Emergency flashers, turn

signal lights, theft deterrent system

9. ST 7.5 A: Starting system, multiport injection system/sequential multi-

fuel port fuel injection system

10. AM2 7.5 A: Starting system 11. SPARE 10 A: Spare fuse 12. EFI NO.2 7.5 A: Multiport fuel injection injec-

system/sequential multiport tion system, emission control system

fuel

13. EFI 15 A: Multiport fuel injection sys- tem/sequential multiport injection system, “EFI NO.1” and “EFI NO.2” fuses

fuel

14. SPARE 15 A: Spare fuse 15. EFI NO.1 7.5 A: Multiport fuel injection injec-

system/sequential multiport tion system

fuel

16. DCC 25 A: “RADIO”, “DOME”, “MPX−

B” and “ECU−B” fuses

17. SPARE 30 A: Spare fuse 18. HORN 10 A: Horn 19. ALT−S 7.5 A: Charging system

2000 CELICA (OM20735U)

249

Celica_U

32. RADIO 15 A: Car audio system 33. WIPER 25 A: Windshield wipers and

washer

34. TURN 7.5 A: Turn signal lights 35. MIR HTR 10 A: No circuit 36. HTR 10 A: Air conditioning system 37. RR WIPER 15 A: Rear window wiper

and washer

38. TAIL 10 A: Tail lights, instrument panel front side

license plate lights,

lights, maker lights

39. FR P/W 20 A: Power windows Fuses (type B) 40. SPARE 7.5 A: Spare fuse 41. a. MPX−B 7.5 A: Wireless remote con-

trol system

b. RR FOG 7.5 A: No circuit c. DOME 7.5 A: Clock, interior lights d. ECU−B 7.5 A: Air conditioning sys-

tem, gauges and meters

42. a. WARNING 5 A: Charging system,

gauges and meters

b. ECU−IG 5 A: Cruise control system c. ABS−IG 5 A: Anti−lock brake sys-

tem d. fans

FAN RLY 5 A: Electric cooling

2000 CELICA (OM20735U)

43. a. PANEL1 7.5 A: Gauges and meters, air conditioning system, electronical- ly controlled automatic transmission system, headlight beam level control system, front fog lights, emergency flasher, turn signal lights

b. PANEL2 7.5 A: Car audio system,

cigarette lighter, glove box light

c. ECU−ACC 7.5 A: Clock, car audio system, power rear view mirror con- trols

44. a. BK/UP LP 5 A: Back−up lights

b. DEF RLY 5 A: Power windows, rear

window defogger

c. BODY ECU−IG 5 A: Theft deterrent

system

d. TENS RDC 5 A: Electronically con- transmission sys- trolled automatic tem, shift lock control system, elec- tric moon roof

Fuses (type C) 45. ABS NO.1 40 A: Anti−lock brake sys-

tem

46. MAIN 40 A: Starting system, daytime

running light system

47. HTR 50 A: Air conditioning system 48. DEF 30 A: Rear window defogger

20. HEAD RH UPR 10 A: Right−hand headlight (high beam), daytime running light system

21. HEAD LH UPR 10 A: Left−hand head-

light (high beam)

22. S/ROOF 15 A: Electric moon roof 23. CIG 15 A: Cigarette lighter 24. FL P/W 20 A: Power windows