2010 Toyota Camry Owners Manual

*1: Shifting to the D position allows the system to select a gear suitable

for the driving conditions. Setting the shift lever to the D position is recommended for normal driving.

*2: Selecting shift ranges using S mode restricts the upper limit of the possible gear ranges, controls engine braking force, and prevents unnecessary upshifting.

Changing shift ranges in S mode

When the shift lever is in the S position, the shift lever can be oper- ated as follows:

Upshifting Downshifting

The initial shift range in S mode is set automatically to 5 or 4 accord- ing to vehicle speed. However, the initial shift range may be set to 3 if AI-SHIFT has operated while the shift lever was in the D position. (→P. 141)

139

2-1. Driving procedures

■ Shift ranges and their functions

Shift range

Function

A gear between 1 and 6 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 5 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 4 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 3 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 2 is automatically selected according to vehicle speed and driving conditions. Setting the gear at 1.

A lower shift range will provide greater engine braking force than a higher shift range.

■Downshifting restrictions

To help ensure safety and driving performance, downshifting operation may sometimes be restricted. In some circumstances, downshifting may not be possible even when the shift lever is operated. (The warning buzzer will sound twice.)

■When driving with the cruise control system

Engine braking will not occur during shift range selection in the D position or S mode, even when downshifting to range 5 or 4. (→P. 166)

■If the shift lever cannot be shifted from P

→P. 467

140

2

2-1. Driving procedures

■If the “S” indicator does not come on even after shifting the shift lever

to S This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the vehicle will operate as if the shift lever is in D.)

■S mode

●When the shift range is 5 or lower, holding the shift lever toward “+” sets

the shift range to 6.

●To prevent the engine from over-revving, upshifting may automatically

occur.

●To protect the automatic transmission, a function is adopted that auto-

matically shifts to the top range when the temperature is too hot.

■AI-SHIFT

The AI-SHIFT automatically shifts the gear to the suitable position according to the driver performance and driving conditions. The AI-SHIFT automatically operates when the shift lever is in the D posi- tion. (Shifting the shift lever to the S position cancels the function.)

141

2-1. Driving procedures Manual transmission∗

■ Shifting the shift lever

Fully depress the clutch pedal before operating the shift lever, and then release it slowly. ■ Shifting the shift lever to R

Shift the shift lever to the R position while lifting up the ring section.

142

∗: If equipped

2

2-1. Driving procedures

■Maximum allowable speeds

Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary.

mph (km/h)

Shift position

Maximum speed

32 (52) 56 (91) 83 (135) 118 (191) 130 (210)

NOTICE

■To prevent damage to the transmission

●Do not shift the shift lever to R without

depressing the clutch pedal.

●Do not lift up the ring section except when shifting the lever to R. ●Shift the shift lever to R only when the vehicle is stationary.

143

2-1. Driving procedures Turn signal lever

Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change. The left hand signal will flash until you release the lever.

■Turn signals can be operated when

Vehicles with smart key system

The “ENGINE START STOP” switch is in ON mode.

Vehicles without smart key system

The engine switch is in the “ON” position. ■If the indicators flash faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

144

2-1. Driving procedures Parking brake

Manual transmission

U.S.A. Canada

Sets the parking brake Fully apply the parking brake while depressing the brake pedal. Releases the parking brake Slightly raise the lever and lower it completely while pressing the but- ton. Automatic transmission

Sets the parking brake* (Depressing the pedal again releases the parking brake.)

*: Fully depress

the parking brake pedal with your left foot while depressing the brake pedal with your right foot.

U.S.A. Canada

NOTICE

■Before driving

Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.

145

2-1. Driving procedures Horn

To sound the horn, press on or close to the

mark.

■After adjusting the steering wheel

Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P. 65)

146

2-2. Instrument cluster Gauges and meters

Vehicles with multi-information display

Vehicles with smart key system: The following gauges, meters and displays illuminate when the “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system: The following gauges, meters and displays illuminate when the engine switch is in the “ON” posi- tion.

Engine coolant temperature gauge Displays the engine coolant temperature. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Multi-information display →P. 155
Fuel gauge Displays the quantity of fuel remaining in the tank.

147

2-2. Instrument cluster

Odometer/trip meter/instrument panel light control and trip meter reset button Switches between odometer and trip meter displays. Pressing and holding the button will reset the trip meter when the trip meter is being displayed. To adjust the brightness of the instrument panel light, turn the button. (→P. 150) Automatic transmission shift position indicator lights →P. 138
Automatic transmission shift range display →P. 138

148

Vehicles without multi-information display

2-2. Instrument cluster

The following gauges, meters and displays illuminate when the engine switch is in the “ON” position. Engine coolant temperature gauge Displays the engine coolant temperature. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Odometer/trip meter/instrument panel light control and trip meter reset button Switches between odometer and trip meter displays. Pressing and holding the button will reset the trip meter when the trip meter is being displayed. To adjust the brightness of the instrument panel light, turn the button. (→P. 150)

149

2-2. Instrument cluster

Odometer, trip meter and outside temperature display Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently. Outside temperature: Displays the outside temperature. Automatic transmission shift position indicator lights →P. 138
Automatic transmission shift range display →P. 138

Instrument panel light control

The brightness of the instrument panel lights can be adjusted.

Darker Brighter When the headlight switch is turned to on, the brightness will be reduced slightly unless the control dial is turned fully clockwise.

NOTICE

■To prevent damage to the engine and its components

●Do not let the indicator needle of the tachometer enter the red zone, which

indicates the maximum engine speed.

●The engine may be overheating if the engine coolant temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (→P. 475)

150

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems.

Instrument cluster (vehicles with multi-information display)

Instrument cluster (vehicles without multi-information display)

151

2-2. Instrument cluster

Center panel

152

2-2. Instrument cluster

■ Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

(U.S.A.)

(CANADA)

(if equipped)

Turn signal indicator (→P. 144)

Headlight high beam indicator (→P. 160)

Slip indicator (→P. 170)

VSC OFF indicator (→P. 171)

“TRAC OFF” indicator (→P. 171)

Engine immobilizer/ alarm system indicator (→P. 80, 82)

Headlight indicator (→P. 159)

Tail light indicator (→P. 159)

Front fog light indicator (→P. 163)

SRS airbag on-off indi- cator (→P. 99)

Cruise control indicator (→P. 166)

Cruise control set indi- cator (→P. 166)

153

2-2. Instrument cluster

■ Warning lights

Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 432)

(CANADA)

(U.S.A.)

(CANADA)

(U.S.A.)

(CANADA)

(if equipped)

(U.S.A.)

(U.S.A.)

(U.S.A.)

(if equipped) (if equipped)

(if equipped)

*: These lights turn on when the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with smart key system) or the engine switch is turned to the “ON” position (vehicles without smart key system) to indicate that a system check is being per- formed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.

CAUTION

■If a safety system warning light does not come on

Should a safety system light such as the ABS or the SRS airbag warning light not come on when you start the engine, this could mean that these sys- tems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

154

2-2. Instrument cluster Multi-information display∗

The multi-information display presents the driver with a variety of driving-related data, including the outside temperature.

● Outside

temperature dis- (→P. 156) play Indicates the outside tempera- ture.

● Trip information

(→P. 156) Displays driving range, fuel consumption and other cruis- ing-related information.

● Warning messages

(→P. 444) Automatically displayed when a malfunction occurs in one of the vehicle’s systems.

● Odometer and trip meter

display Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the dis- tance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances indepen- dently.

∗: If equipped 155

2-2. Instrument cluster

Switch the display

Display items can be switched by pressing the “DISP” button.

The display will return to the out- side temperature display when the “DISP” button is pressed and held.

● Outside temperature

● Cruising range

Displays the outside air temperature.

The temperature range that can be displayed is from -40°F (-40°C) to 122°F (50°C).

Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed. • When only a small amount of fuel is added to the

tank, the display may not be updated.

● Average fuel consumption after refueling

Displays the average fuel consumption since the vehicles was last refueled.

156

2-2. Instrument cluster

● Driving distance

Displays the driving distance since the engine was started.

● Average vehicle speed

Displays the average vehicle speed since the engine was started.

● Cruise information off

Displays the odometer and trip meters only.

● Zoom display of odometer and trip meter

Displays the odometer and one of the trip meters simultaneously.

■Outside temperature display

In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change. ●When stopped, or driving at low speeds (less than 12 mph [20 km/h]) ●When the outside temperature has changed suddenly (at the entrance/

exit of a garage, tunnel, etc.)

157

2-2. Instrument cluster

NOTICE

■The multi-information display at low temperatures

Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed.

158

2

2-3. Operating the lights and wipers Headlight switch

The headlights can be operated manually or automatically.

For U.S.A.

The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on. The headlights and parking lights turn on and off automatically. (When the “ENGINE START STOP” switch or the engine switch is in ON) Daytime running light system is off.

159

2-3. Operating the lights and wipers

For Canada

The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on. The headlights and parking lights turn on and off automatically. (When the “ENGINE START STOP” switch or the engine switch is in ON)

Turning on the high beam headlights

With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams. Release the lever to turn them off. You can flash the high beams with the headlights on or off.

160

2

2-3. Operating the lights and wipers

■The headlights can be operated automatically when

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

Vehicles without smart key system

The engine switch is in the “ON” position.

■Daytime running light system

To make your vehicle more visible to other drivers, the headlights turn on automatically (at a reduced intensity) whenever the engine is started and the parking brake is released. Daytime running lights are not designed for use at night. For U.S.A.: Daytime running lights can be turned off by operating the switch.

■Headlight control sensor

The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. Doing so the sensor detecting the level of ambient light and may cause the automatic headlight sys- tem to malfunction.

interferes with

161

2-3. Operating the lights and wipers

■Automatic light off system

Vehicles with smart key system

●When the headlights are on: The headlights and tail lights turn off 30 sec- onds after all doors are closed with the “ENGINE START STOP” switch OFF. (The lights turn off immediately if on the key is pressed after all doors are locked.)

●When only the tail lights are on: The tail lights turn off automatically if the “ENGINE START STOP” switch is turned OFF and the driver’s door is opened.

To turn the lights on again, turn the “ENGINE START STOP” switch to IGNI- or TION ON mode, or turn the headlight switch off and then back to

position.

If any of the doors or trunk lid is kept open, the lights automatically turn off after 20 minutes.

Vehicles without smart key system

●When the headlights are on: The headlights and tail lights turn off 30 sec- onds after all doors are closed with the engine switch OFF. (Vehicles with wireless remote control: The lights turn off immediately if on the key is pressed after all doors are locked.)

●When only the tail lights are on: The tail lights turn off automatically if the

engine switch is turned OFF and the driver’s door is opened.

To turn the lights on again, turn the engine switch to the “ON” position, or turn the headlight switch off and then back to If any of the doors or trunk lid is kept open, the lights automatically turn off after 20 minutes.

position.

or

■Customization that can be configured at Toyota dealer

Settings (e.g. Light sensor sensitivity) can be changed. (Customizable features →P. 510)

NOTICE

■To prevent battery discharge

Do not leave the lights on longer than necessary when the engine is not run- ning.

162

2-3. Operating the lights and wipers Fog light switch∗

The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam.

Off Front fog lights on

∗: If equipped 163

2-3. Operating the lights and wipers Windshield wipers and washer

Wiper intervals can be adjusted for intermittent operation.

windshield

Intermittent wiper operation Low speed windshield wiper operation High wiper operation Temporary operation

speed windshield

the

Increases intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency

164

2-3. Operating the lights and wipers

Wash/wipe operation

Wipers operate automatically.

■The windshield wiper and washers can be operated when

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

Vehicles without smart key system

The engine switch is in the “ON” position.

■If no windshield washer fluid sprays

Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.

NOTICE

■When the windshield is dry

Do not use the wipers, as they may damage the windshield.

■When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.

■When a nozzle becomes blocked

Do not try to clear it with a pin or other object. The nozzle will be damaged.

165

2-4. Using other driving systems Cruise control

Use the cruise control to maintain a set speed without using the accelerator.

Indicators Cruise control switch

Turn the “ON-OFF” button on. At this time, the cruise control indicator will come on. Press the button once more to deactivate the cruise control.

Accelerate or decelerate to the desired speed and push the lever down to set the cruise control speed.

At this time, the cruise control set indicator will come on.

■ Setting the vehicle speed STEP 1

STEP 2

166

2

■ Adjusting the speed setting

2-4. Using other driving systems

Increase speed Decrease speed Hold the lever until the desired speed setting is obtained. Fine adjustment of the set speed (approximately 1.0 mph [1.6 km/h]) can be made by lightly pushing the lever up or down and releasing it.

■ Canceling and resuming regular acceleration

Cancel Pull the lever towards you to cancel cruise control. The speed setting is also can- celed when the brakes are applied or the clutch pedal (manual is depressed. Resume To resume cruise control and return to the set speed, push the lever up.

transmission)

167

2-4. Using other driving systems

■Cruise control can be set when

●Automatic transmission:

The shift lever is in D, 4, 5 or 6 range of S. ●Vehicle speed is above 25 mph (40 km/h).

■Accelerating

The vehicle can be accelerated normally. After acceleration, the set speed resumes.

■Automatic cruise control cancellation

The set speed is automatically canceled in any of the following situations. ●Actual vehicle speed falls more than 10 mph (16 km/h) below the preset

vehicle speed. At this time, the memorized set speed is not retained.

●Actual vehicle speed is below 25 mph (40 km/h). ●VSC is activated.

■If the cruise control indicator light flashes

Press the “ON-OFF” button once to deactivate the system, and then press the button again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Contact your Toyota dealer and have your Toyota inspected.

168

2

2-4. Using other driving systems

CAUTION

■To avoid operating the cruise control by mistake

Keep the “ON-OFF” button off when not in use.

■Situations unsuitable for cruise control

Do not use cruise control in any of the following situations. Doing so may result in control of the vehicle being lost and could cause an accident resulting in death or serious injury. ●In heavy traffic ●On roads with sharp bends ●On winding roads ●On slippery roads, such as those covered with rain, ice or snow ●On steep hills

169

2-4. Using other driving systems Driving assist systems

To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■ ABS (Anti-lock Brake System)

Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.

■ Brake assist

Generates an increased level of braking force after the brake pedal is depressed, when the system detects a panic stop situation.

■ VSC (Vehicle Stability Control)

Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces.

■ TRAC (Traction Control)

Maintains drive power and prevents the front wheels from spinning when starting the vehicle or accelerating on slippery roads.

When VSC and TRAC are operating

If the vehicle is in danger of slip- ping or the front wheels spin, the indicator flashes to indicate that VSC/TRAC have been engaged. A buzzer (intermittent) sounds to indicate that VSC is operating.

170

2-4. Using other driving systems

To disable TRAC and/or VSC

If the vehicle gets stuck in fresh snow or mud, TRAC and VSC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it. ■ Turning off TRAC

Quickly push and release the button to turn off TRAC.

■ Turning off TRAC and VSC

The “TRAC OFF” indicator light should come on. Push the button again to turn the system back on.

Push and hold the button for more than 3 seconds while the vehicle is stopped to turn off TRAC and VSC.

The “TRAC OFF” and VSC OFF indicator lights should come on. Push the button again to turn the system back on.

171

2-4. Using other driving systems

■Automatic reactivation of TRAC and VSC

Vehicles with smart key system

Turning the “ENGINE START STOP” switch OFF after turning off the TRAC and VSC systems will automatically re-enable them.

Vehicles without smart key system

Turning the engine switch OFF after turning off the TRAC and VSC systems will automatically re-enable them.

■Automatic TRAC reactivation

If only the TRAC system is turned off, the TRAC system will turn on when vehicle speed increases.

■Automatic TRAC and VSC reactivation

If the TRAC and VSC systems are turned off, the systems will not turn on even when vehicle speed increases.

■Sounds and vibrations caused by ABS, brake assist, VSC and TRAC ●A sound may be heard from the engine compartment when the engine is started or just after the vehicle begins to move. This sound does not indi- cate that a malfunction has occurred in any of these systems.

●Any of the following conditions may occur when the above systems are

operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop. • The brake pedal may pulsate slightly after ABS is activated. • The brake pedal may move down slightly after ABS is activated.

■If the slip indicator comes on...

It may indicate a malfunction in the VSC and TRAC. Contact your Toyota dealer.

172

2

2-4. Using other driving systems

CAUTION

■ABS does not operate effectively when

●Tires with inadequate gripping ability are used (such as excessively worn

tires on a snow covered road).

●The vehicle hydroplanes while driving at high speed on the wet or slick

road.

■Stopping distance when ABS is operating on the wet or slick roads

ABS is not designed to shorten the vehicle's stopping distance. Always maintain a safe distance from the vehicle in front of you in the following situ- ations. ●When driving on dirt, gravel or snow-covered roads ●When driving with tire chains ●When driving over bumps in the road ●When driving over roads with potholes or uneven roads

■TRAC may not operate effectively when

Directional control and power may not be achievable while driving on slip- pery road surfaces, even if the TRAC system is operating. Do not drive the vehicle in conditions where stability and power may be lost.

173

2-4. Using other driving systems

CAUTION

■When VSC is activated

The slip indicator light flashes and a warning buzzer sounds. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes and a buzzer sounds.

■When TRAC and VSC are off

Be especially careful and drive at a speed appropriate to the road condi- tions. As these are systems to ensure vehicle stability and driving force, do not turn off TRAC and VSC unless necessary.

■Replacing tires

Make sure that all tires are of the same size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the recom- mended tire pressure level. The ABS and VSC system will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.

■Handling of tires and suspension

Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.

174

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load. ● Stow cargo and luggage in the trunk whenever possible. ● Be sure all items are secured in place. ● Be careful to keep the vehicle level. Placing the weight as far for-

ward as possible helps maintain vehicle balance.

● For better fuel economy, do not carry unnecessary weight.

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) - (Total weight of occupants) Steps for Determining Correct Load Limit ⎯ (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehi- cle’s placard.

(2) Determine the combined weight of the driver and passengers

that will be riding in your vehicle.

(3) Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4) The resulting figure equals the available amount of cargo and

luggage load capacity. For example, if the XXX amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of avail- able cargo and luggage load capacity is 650 lbs. (1400 - 750
(150 × 5) = 650 lbs.)

(5) Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

175

2-5. Driving information

(6)

If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (→P. 183)

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 900 lb. (410
kg), the available amount of cargo and luggage load capacity will be as follows: 900 lb. - 366 lb. = 534 lb. (410 kg -166 kg = 244 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

534 lb. - 388 lb. = 146 lb. (244 kg - 176 kg = 68 kg) As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

176

2

2-5. Driving information

CAUTION

■Storage precautions

Observe the following precautions. Failing to do so may result in death or serious injury. ●Vehicles with fold-down type rear seat: To prevent cargo and luggage from sliding forward during braking, do not stack anything in the enlarged trunk. Keep cargo and luggage low, as close to the floor as possible.

●Vehicles with fold-down type rear seat: Never allow anyone to ride in the enlarged trunk. It is not designed for passengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer death or serious bodily injury, in the event of sudden braking, sudden swerving or a collision.

●Do not place cargo or luggage in or on the following locations as the item may get under the clutch, brake or accelerator pedal and prevent the pedals from being depressed properly, block the driver’s vision, or hit the driver or passengers, causing an accident. • Driver’s feet • Front passenger or rear seats (when stacking items) • Package tray • Instrument panel • Dashboard

●Secure all items in the occupant compartment, as they may shift and injure someone during sudden braking, sudden swerving or an acci- dent.

■Capacity and distribution

●Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

●Even if the total load of occupant's weight and the cargo load is less

than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking con- trol which may cause death or serious injury.

177

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. ■ Total load capacity: 900 lb. (410 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

■ Seating capacity: 5 occupants (Front 2, Rear 3)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person.

■ Towing capacity: 1000 lb. (453 kg) ■ Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

■Total load capacity and seating capacity

These details are also described on the tire and loading information label. (→P. 392)

CAUTION

■Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

178

2

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations

● Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

● Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

● Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the front tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires. ■ Before driving the vehicle

Perform the following according to the driving conditions. ● Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. ● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

● Remove any ice that has accumulated on the vehicle chassis. ● Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

179

2-5. Driving information

■ When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

■ When parking the vehicle

Park the vehicle and move the shift lever to P (automatic trans- mission) or R (manual transmission) without setting the parking brake. The parking brake may freeze up, preventing it from being released.

Selecting tire chains

Use the correct tire chain size when mounting the snow chains. Chain size is regulated for each tire size.

Side chain:

0.12 in. (3 mm) in diameter 0.39 in. (10 mm) in width 1.18 in. (30 mm) in length

Cross chain:

0.16 in. (4 mm) in diameter 0.55 in. (14 mm) in width 0.98 in. (25 mm) in length

Regulations on the use of snow chains

● Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains.

● Install the chains on the front tires. ● Retighten the chains after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

180

2-5. Driving information

■Tire chains

Observe the following precautions when installing and removing chains. ●Install and remove tire chains in a safe location. ●Install tire chains on the front tires only. Do not install tire chains on rear

tires.

●Install tire chains following the instructions provided in the accompanying

manual.

CAUTION

■Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. ●Use tires of the size specified for your vehicle. ●Maintain the recommended level of air pressure. ●Do not drive in excess of 75 mph (120 km/h), regardless of the type of

snow tires being used.

●Use snow tires on all, not just some wheels.

■Driving with tire chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. ●Do not drive in excess of the speed limit specified for the tire chains being

used or 30 mph (50 km/h), whichever is lower.

●Avoid driving on bumpy road surfaces or over potholes. ●Avoid sudden turns and braking, as use of chains may adversely affect

vehicle handling.

●Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

181

2-5. Driving information

NOTICE

■Repairing or replacing snow tires

Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

■Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

182

2

2-5. Driving information Trailer towing

Your vehicle is designed primarily as a passenger carrying vehicle. Towing a trailer will have an adverse effect on handling, perfor- mance, braking, durability, and fuel consumption. For your safety and the safety of others, do not overload the vehicle or trailer. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. ■ Weight limits

Confirm that the total trailer weight, gross vehicle weight, gross axle weight and trailer tongue load are all within the limits.

■ Gross vehicle weight

The gross vehicle weight must not exceed the Gross Vehicle Weight Rating (GVWR) indicated on the Certification Label. The gross vehicle weight is the sum weight of the unloaded vehicle, driver, passengers, luggage, hitch and trailer tongue load. Also included is the weight of any special equipment installed on your vehicle.

■ Gross axle weight

The load on either the front or rear axle resulting from distribu- tion of the gross vehicle weight on both axles must not exceed the Gross Axle Weight Rating (GAWR) listed on the Certification Label.

Certification label

183

2-5. Driving information

■ Trailer tongue load

The trailer cargo load should be distributed so that the tongue load is 9 to 11% of the total trailer weight, not exceeding the maximum 100 lb. (45 kg). (Tongue load / Total trailer weight x 100 = 9 to 11%) The total trailer weight and tongue load can be measured with platform scales found at highway weighing stations, building supply companies, trucking companies, junk yards, etc.

Total trailer weight Tongue load

Towing a trailer

Contact your Toyota dealer for further information about additional requirements such as a towing kits, etc.

Hitch

Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Even though the vehicle may be rated for towing a higher weight, the operator must never exceed the maxi- mum weight rating specified for the trailer hitch.

184

2-5. Driving information

■Before towing

●Ensure that your vehicle’s tires are properly inflated. (→P. 392) ●Trailer tires should be inflated according to the trailer manufacturer's rec-

ommendation.

●All trailer lights must work in order to be legal. ●Confirm all lights work each time you connect them. ●Check that your vehicle remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle is not level, and check for improper tongue load, overloading, worn suspension, or other possible causes.

●Make sure the trailer cargo is securely loaded. ●Check that your rear view mirrors conform to any federal, state/provincial or local regulations. If they do not, install rear view mirrors appropriate for towing purposes. ■Break-in schedule

Toyota recommends that you do not use a new vehicle or a vehicle with any new power train components (engine, transmission, differential, wheel bear- ings, etc.) to tow a trailer for the first 500 miles (800 km) of driving.

■Maintenance

●If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Scheduled Maintenance Guide” or “Owner's Manual Supplement”.)

●Retighten the fixing bolts of the towing ball and bracket after approxi-

mately 600 miles (1000 km) of trailer towing.

185

2-5. Driving information

CAUTION

■To avoid accident or injury

●The total trailer weight (trailer weight plus the weight of cargo) must not

exceed 1000 lb. (453 kg).

●Do not exceed the trailer hitch assembly weight, gross vehicle weight,

gross axle weight and trailer tongue load capacities.

●Never load more weight in the back than in the front of the trailer. About 60% of the load should be in the front half of the trailer, and the remaining 40% in the rear.

■Hitches

●If you wish to install a trailer hitch, contact your Toyota dealer. ●Use only a hitch that conforms to the total trailer weight requirement. ●Follow the directions supplied by the hitch manufacturer. ●Lubricate the hitch ball with a light coat of grease. ●Remove the trailer hitch whenever you are not towing a trailer. After removing the hitch, seal any mounting hole in the vehicle body to prevent entry of any substances into the vehicle.

■When towing a trailer

●Never tap into your vehicle's hydraulic system, as this will lower the vehi-

cle's braking effectiveness.

●Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering into another lane.

186

2

2-5. Driving information

NOTICE

■When installing a trailer hitch

●Use only the position recommended by your Toyota dealer. Do not install

the trailer hitch on the bumper; this may cause body damage.

●Do not use axle-mounted hitches, as they can cause damage to the axle

housing, wheel bearings, wheels or tires.

■Brakes

Toyota recommends trailers with brakes that conform to all applicable fed- eral and state/provincial regulations.

■Safety chain

A safety chain must always be used between the towing vehicle and the trailer. Leave sufficient slack in the chain for turns. The chain should cross under the trailer tongue to prevent the tongue from dropping to the ground in the case that it becomes damaged or separated. For the correct safety chain installation procedure, ask your Toyota dealer.

■Do not directly splice trailer lights

Directly splicing trailer lights may damage your vehicle's electrical system and cause a malfunction.

Trailer towing tips

Your vehicle will handle differently when towing a trailer. The 3 main causes of vehicle-trailer accidents are driver error, excessive speed and improper trailer loading. Keep the following in mind when towing. ● Before starting out, check the trailer lights and the vehicle-trailer

connections. Recheck after driving a short distance.

● Practice turning, stopping and reversing with the trailer attached in an area away from traffic until you become accustomed to the feel of the vehicle.

187

2-5. Driving information

● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to right. (This is generally opposite to reversing without a trailer attached.) Avoid sharp or prolonged turning. Have someone guide you when reversing to reduce the risk of an acci- dent.

● As stopping distance is increased when towing a trailer, vehicle-to- vehicle distance should be increased. For each 10 mph (16 km/h) of speed, allow at least one vehicle and trailer length.

● Avoid sudden braking as you may skid, resulting in jackknifing and

loss of control. This is especially true on wet or slippery surfaces.

● Avoid jerky starts or sudden acceleration. ● Avoid jerky steering and sharp turns, and slow down before mak-

ing turns.

● Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a larger than normal turning radius.

● Crosswinds and rough roads will adversely affect handling of your vehicle and trailer, causing sway. Periodically check the rear to prepare for being passed by large trucks or buses, which may cause your vehicle and trailer to sway. If swaying occurs, firmly grip the steering wheel, reduce speed immediately but gradually, and steer straight ahead. Never increase speed. If you make no extreme correction with the steering or brakes, your vehicle and trailer will stabilize.

● Take care when passing other vehicles. Passing requires consider- able distance. After passing a vehicle, do not forget the length of your trailer, and be sure you have plenty of room before changing lanes.

188

2-5. Driving information

● In order to maintain efficient engine braking and electrical charging performance, do not use overdrive (automatic transmission) or the 5th gear (manual transmission).

● Due to the added load of the trailer, your vehicle's engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade. If the engine coolant temperature gauge indicates overheating, immediately turn off the air condition- ing (if in use), pull your vehicle off the road and stop in a safe spot. (→P. 475)

● Always place wheel blocks under both the vehicle and the trailer wheels when parking. Apply the parking brake firmly, and put the transmission in P (automatic transmission) or in first or R (manual transmission). Avoid parking on a slope, but if unavoidable, do so only after performing the following:

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

Apply the brakes and keep them applied. Have someone place wheel blocks under both the vehicle and trailer wheels. When the wheel blocks are in place, release the brakes slowly until the blocks absorb the load. Apply the parking brake firmly. Shift into first or R (manual transmission) or P (automatic transmission) and turn off the engine.

● When restarting after parking on a slope: STEP 1

With the transmission in the P position (automatic transmis- sion) or the clutch pedal (manual transmission) depressed, start the engine. On vehicles with an automatic transmission, be sure to keep the brake pedal pressed. Shift into a forward gear. If reversing, shift into the R position. Release the parking brake (also brake pedal on vehicles with automatic transmission), and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks.

STEP 2

STEP 3

STEP 4

189

2-5. Driving information

CAUTION

■To avoid an accident

●Do not exceed 45 mph (72 km/h) or posted towing speed limit, whichever is lower. As instability (swaying) of the towing vehicle-trailer combination increases as speed increases, exceeding 45 mph (72 km/h) may cause loss of control.

●Slow down and downshift before descending steep or long downhill

grades. Do not make sudden downshifts.

●Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

190

2-5. Driving information Dinghy towing (automatic transmission)

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

■To avoid serious damage to your vehicle

Do not tow your vehicle with four wheels on the ground.

191

2-5. Driving information Dinghy towing (manual transmission)

Your vehicle can be dinghy towed in a forward direction (with 4
wheels on the ground) behind a motor home.

Towing your vehicle with 4 wheels on the ground

To prevent damage to your vehicle, perform the following procedures before towing. STEP 1

Shift the shift lever to neutral. Switch to the “ACC” position. (→P. 135) Ensure that the audio system and other powered devices have been turned off. Release the parking brake. After towing, run the engine in idle for at least 3 minutes before driv- ing the vehicle.

STEP 2

STEP 3

■Necessary equipment and accessories

Specialized equipment and accessories are required for dinghy towing. Con- tact the service branch of the motor home manufacturer regarding recom- mended equipment.

192

NOTICE

■Dinghy towing direction

2-5. Driving information

Do not tow the vehicle backwards. Doing so may cause serious damage.

■To prevent the steering from locking

Ensure the engine switch is in the “ACC” position.

193

3-1. Using the air conditioning system and defogger Automatic air conditioning system∗

Air outlets are automatically selected and fan speed is automatically adjusted according to the temperature setting.

Air outlet display

Fan speed display

Driver’s side temperature setting display Driver’s side temper- ature control

“DUAL” button

Front passenger’s side temperature setting display

Change the air outlets used (air flow selector button)

Front passenger’s side temperature control

Automatic mode

Off

Fan speed (fan speed selector)

Windshield defogger

Air conditioning on/off switch

Outside air or recirculated air mode

196

∗: If equipped

3-1. Using the air conditioning system and defogger

Using the automatic mode

STEP 1

Press The air conditioning system will begin to operate. Air outlets and fan speed are automatically adjusted according to the temperature setting.

STEP 2

Turning

to the right increases the temperature and

to the left decreases the temperature on the

turning driver’s side. The temperature for the driver and passenger seats can be set sep- arately. (→P. 197)

Adjusting the settings

■ Adjusting the temperature setting

Turning

to the right increases the temperature and turning

to the left decreases the temperature on the driver’s side.

to the right (increase) or

Turn to the left (decrease) on the passenger’s side to separately adjust the temperature for the pas-

senger’s and driver’s side (dual mode). Press to return the driver’s and passenger’s side temperatures to the same setting (simulta- neous mode). The air conditioning system switches between dual and simultaneous

mode each time

is pressed.

197

3-1. Using the air conditioning system and defogger

■ Adjusting the fan speed

Press “∧” (increase) or “∨” (decrease) on the fan speed selector. The fan speed is shown on the display. (7 levels) Press

to turn the fan off.

■ Changing the air outlets

Press the air flow selector button. The air outlets switch each time the button is pressed. The air flow shown on the display indicates the following.

Air flows to the upper body.

Air flows to the upper body and feet.

Air flows to the feet.

198

3-1. Using the air conditioning system and defogger

Air flows to the feet and the windshield defogger operates.

Recirculated air mode will auto- matically switch to outside air mode.

■ Switching between outside air and recirculated air modes

Press The mode switches between outside air mode (indicator off) and recircu- lated air mode (indicator on) modes each time

is pressed.