Download PDF Manual

“ENGINE START STOP” switch is turned to ACCESSORY mode or turned OFF. They cannot, however, be operated once either front door is opened.


Vehicles without smart key system


The moon roof can be operated for approximately 45 seconds after the engine switch is turned to “ACC” or “LOCK” position. It cannot, however, be operated once either front door is opened.


■Jam protection function


If an object is detected between the moon roof and the frame while closing or tilting down, travel is stopped and the moon roof opens slightly.


■To reduce wind noise


Drive with the moon roof opened to slightly before the fully open position as driving with the moon roof opened fully will cause wind noise.


■Sunshade


The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened.


■Moon roof open reminder function


Vehicles with smart key system


An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the “ENGINE START STOP” switch OFF.


Vehicles without smart key system


An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the engine switch OFF.


72


1


1-4. Opening and closing the windows


CAUTION


■Opening the moon roof


Observe the following precautions. Failing to do so may cause death or serious injury. ●Do not allow any passengers to put their hands or heads outside the vehi-


cle while it is moving.


●Do not sit on top of the moon roof.


■Closing the moon roof


Observe the following precautions. Failing to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their bod- ies in a position where they could be caught when the moon roof is being operated.


●Do not allow children to operate the moon roof.


Closing the moon roof on someone can cause death or serious injury.


■Jam protection function


●Never try jamming any part of your body to activate the jam protection


function intentionally.


●The jam protection function may not work if something gets caught just


before the moon roof fully closes.


73


1-5. Refueling Opening the fuel tank cap


Perform the following steps to open the fuel tank cap. ■ Before refueling the vehicle


Vehicles with smart key system


Turn the “ENGINE START STOP” switch OFF and ensure that all the doors and windows are closed. Vehicles without smart key system


Turn the engine switch OFF and ensure that all the doors and windows are closed.


■ Opening the fuel tank cap STEP 1


Open the fuel filler door.


STEP 2


Turn the fuel tank cap slowly to open.


74


1-5. Refueling


STEP 3


Hang the fuel tank cap on the back of the fuel filler door.


Closing the fuel tank cap


When replacing the fuel tank cap, turn it until a clicking sound is heard.


After releasing your hand, the cap will turn slightly to the opposite direction.


■Fuel type


Unleaded gasoline (87 Octane rating [Research Octane Number 91] or higher)


■Fuel tank capacity


18.5 gal. (70 L, 15.4 Imp. gal.)


75


1-5. Refueling


CAUTION


■Refueling the vehicle


Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. ●Touch the vehicle or some other metal surface to discharge any static


electricity. Sparks resulting from discharging static electricity may cause the fuel vapors to ignite.


●Always hold the grips on the fuel tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out of the filler neck and cause injury.


●Do not allow anyone that has not discharged static electricity from their


bodies to come close to an open fuel tank.


●Do not inhale vaporized fuel.


Fuel contains substances that are harmful if inhaled.


●Do not smoke while refueling the vehicle.


Doing so may cause the fuel to ignite and cause a fire.


●Do not return to the vehicle or touch any person or object that is statically


charged. This may cause static electricity to build up, resulting in a possible ignition hazard.


■When replacing the fuel cap


Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.


76


1-5. Refueling


NOTICE


■Refueling


Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle's painted surface.


77


1-6. Theft deterrent system Engine immobilizer system


The vehicle's keys have built-in transponder chips that prevent the engine from starting if the key has not been previously registered in the vehicle's on-board computer. Never leave the keys inside the vehicle when you leave the vehicle.


Vehicles with smart key sys- tem: The indicator light flashes after the “ENGINE START STOP” switch has been turned OFF to indicate that the sys- tem is operating. Vehicles without smart key system: The light flashes after the key has been removed the engine switch to indicate that the sys- tem is operating.


indicator


from


■System maintenance


The vehicle has a maintenance-free type of engine immobilizer system.


■Conditions that may cause the system to malfunction


●If the key is in contact with a metallic object ●If the key is in close proximity to or touching a key to the security system


(key with a built-in transponder chip) of another vehicle


78


1-6. Theft deterrent system


■Certifications for the engine immobilizer system (for vehicles sold in


U.S.A.)


Vehicles with smart key system


FCC ID: NI4TMIMB-1


Vehicles without smart key system


FCC ID: MOZRI-20BTY (Made in Japan) FCC ID: MOZRI-21BTY (Made in Canada) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.


■Certifications for the engine immobilizer system (for vehicles sold in


Canada) This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.


CAUTION


Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.


NOTICE


■To prevent damage to the key


Do not modify, remove or disable the engine immobilizer system. If any unauthorized changes or modifications are made, the proper operation of the system cannot be guaranteed.


79


1-6. Theft deterrent system Alarm (if equipped)


The system sounds the alarm and flashes lights when forcible entry is detected. ■ Triggering of the alarm


The alarm is triggered in the following situations. ● A locked door or trunk is unlocked or opened without the key, wireless remote control or entry function of the smart key sys- tem.


● The hood is opened while the vehicle is locked. ● The battery is reconnected.


■ Setting the alarm system


Close the doors, trunk and hood, and lock all doors. The system will be set automati- cally after 30 seconds.


indicator


The light changes from being on to flashing when the system is set.


■ Deactivating or stopping the alarm


Do one of the following to deactivate or stop the alarm. ● Unlock the doors or trunk. ● Start the engine.


80


1


1-6. Theft deterrent system


■Items to check before locking the vehicle


To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following. ●Nobody is in the vehicle. ●The windows and moon roof are closed before the alarm is set. ●No valuables or other personal items are left in the vehicle.


■Triggering of the alarm


The alarm may be triggered in the following situations. (Stopping the alarm deactivates the system.) ●A person inside the vehicle opens a door, the trunk or hood. ●The battery is recharged or replaced when the vehicle is locked.


■When the battery is disconnected


Be sure to deactivate the alarm system. If the battery is discharged before deactivating the alarm system, the alarm may be triggered when the battery is reconnected.


81


1-6. Theft deterrent system Theft prevention labels (for U.S.A.)


These labels are attached to the vehicle to reduce vehicle theft by facilitating the tracing and recovery of parts from sto- len vehicles. Do not remove under penalty of law.


82


1-7. Safety information Correct driving posture


Drive in a good posture as follows:


and to


Sit upright and well back in the seat. (→P. 50) Adjust the position of the seat forward or backward to ensure the pedals can be easily reached depressed the extent required. (→P. 50) Adjust the seatback so that the controls are easily oper- able. Adjust the tilt and telescopic positions of the steering wheel downward so the air- bag is facing your chest. (→P. 64) Lock the head restraint in place with the center of the head restraint closest to the top of your ears. (→P. 54) Wear the seat belt correctly. (→P. 56)


83


1-7. Safety information


CAUTION


■While driving


●Do not adjust the position of the driver's seat while driving.


Doing so could cause the driver to lose control of the vehicle.


●Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.


●Do not place anything under the front seats.


Objects placed under the front seats may become jammed in the seat tracks and stop the seat from locking in place. This may lead to an acci- dent. The adjustment mechanism may also be damaged.


■Adjusting the seat position


●Take care when adjusting the seat position to ensure that other passen-


gers are not injured by the moving seat.


●Do not put your hands under the seat or near the moving parts to avoid


injury. Fingers or hands may become jammed in the seat mechanism.


84


1-7. Safety information SRS airbags


The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.


85


Front airbags Driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas- senger from impact with interior components. Driver knee airbag Can help provide driver protection.


Side and curtain shield airbags Side airbags Can help protect the torso of the front seat occupants. Curtain shield airbags Can help protect primarily the head of occupants in the outer seats.


1-7. Safety information


Airbag system components


Front airbag sensors Front passenger occupant classification system (ECU and sensors) Side and curtain shield air- bag sensors Front passenger airbag Side airbags Curtain shield airbags “AIR BAG ON” and “AIR BAG OFF” indicator lights SRS warning light Front passenger’s seat belt buckle switch


Airbag sensor assembly Curtain shield airbag sen- sors Driver airbag Driver’s seat position sen- sor (with power seat) Driver’s seat belt buckle switch Driver’s seat position sen- sor (with manual seat) Driver knee airbag


86


1


1-7. Safety information


Your vehicle is equipped with ADVANCED AIRBAGS designed based on US motor vehicle safety standards (FMVSS208). The airbag sys- tem controls airbag deployment power for the driver and front pas- senger. The driver airbag system consists of the driver seat's position sensor etc. The front passenger's airbag system consists of the front passenger occupant classification sensor etc. The main SRS airbag system components are shown above. The SRS airbag system is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sensor and an airbag sensor. In certain types of severe frontal or side impacts, the SRS airbag sys- tem triggers the airbag inflators. A chemical reaction in the inflators quickly fills the airbags with non-toxic gas to help restrain the motion of the occupants.


87


1-7. Safety information


■SRS warning light


This warning light system monitors the airbag sensor assembly, front airbag sensors, side and curtain shield airbag sensors, curtain shield airbag sen- sors, driver's seat position sensor, driver's seat belt buckle switch, front pas- senger occupant classification system, “AIR BAG ON” indicator light, “AIR BAG OFF” indicator light, front passenger's seat belt buckle switch, seat belt pretensioner assemblies, interconnecting wiring and power sources. (→P. 382)


inflators,


■If the SRS airbags deploy (inflate)


●Bruising and slight abrasions may result from contact with a deploying


(inflating) SRS airbag.


●A loud noise and white powder will be emitted. ●Parts of the airbag module (steering wheel hub, airbag cover and inflator) as well as the front seats, and parts of the front and rear pillars and roof side rail, may be hot for several minutes. The airbag itself may also be hot.


●The front windshield may crack.


■Operating conditions (front airbags)


●The SRS front airbags will deploy if the severity of the frontal impact is above the designed threshold level, comparable to an approximate 15
mph (25 km/h) collision when the vehicle impacts straight into a fixed bar- rier that does not move or deform. However, this threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if the vehicle is involved in an underride collision (e.g. a collision in which the front of the vehicle “underrides”, or goes under, the bed of a truck, etc.).


●It is possible that in some collisions where the forward deceleration of the vehicle is very close to the designed threshold level, the SRS front air- bags and the seat belt pretensioners may not activate together.


●The SRS front passenger airbag will not activate if there is no passenger sitting in the front passenger seat. However, the front passenger airbag may deploy if luggage is put in the seat, or the seat belt is fastened, even if the seat is unoccupied. (→P. 97)


88


1


1-7. Safety information


■Operating conditions (side airbags and curtain shield airbags)


●The SRS side airbags and curtain shield airbags are designed to inflate when the passenger compartment is subjected to a severe impact from the side.


●The SRS side airbag on the passenger seat will not activate if there is no passenger sitting in the front passenger seat. However, the side airbag on the passenger seat may deploy if luggage is put in the seat, even if the seat is unoccupied. (→P. 97)


■Conditions under which the SRS airbags may deploy (inflate), other


than a collision The SRS front airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.


●Hitting a curb, edge of pavement or


hard surface


●Falling into or jumping over a deep hole ●Landing hard or vehicle falling


■Types of collisions that may not deploy the SRS airbag (front airbags) The SRS front airbags are generally not designed to inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low- speed frontal collision. But, whenever a collision of any type causes suffi- cient forward deceleration of the vehicle, deployment of the SRS front air- bags may occur.


●Collision from the side ●Collision from the rear ●Vehicle rollover


89


1-7. Safety information


■Types of collisions that may not deploy the SRS airbag


(side airbags and curtain shield airbags) The SRS side airbags and curtain shield airbag system may not activate if the vehicle is subjected to a collision from the side at certain angles, or a col- lision to the side of the vehicle body other than the passenger compartment.


●Collision from the side to the vehicle body other than the passenger com- partment


●Collision from the side at an angle


The SRS side airbags and curtain shield airbags are not generally designed to inflate if the vehicle is involved in a frontal or rear collision, if it rolls over, or if it is involved in a low-speed side collision.


●Collision from the front ●Collision from the rear ●Vehicle rollover


90


1


1-7. Safety information


■When to contact your Toyota dealer


In the following cases, contact your Toyota dealer as soon as possible. Do not disconnect the battery cables before contacting your Toyota dealer. ●Any of the SRS airbags have been inflated.


●The front of the vehicle is damaged or deformed, or was involved in an acci- dent that was not severe enough to cause the SRS airbags to inflate.


●A portion of a door is damaged or deformed, or the vehicle was involved in an accident that was not severe enough to cause the SRS side airbags and curtain shield airbags to inflate.


●The pad section of the steering wheel or dashboard near the front passenger airbag cover or lower portion of the instrument panel is scratched, cracked, or otherwise damaged.


●The surface of the seats with the side airbag is scratched, cracked, or other- wise damaged.


●The portion of the front pillars, rear pil- lars or roof side rail garnishes (padding) containing the curtain shield airbags inside is scratched, cracked or other- wise damaged.


91


1-7. Safety information


CAUTION


■SRS airbag precautions


Observe the following precautions regarding the airbags. Failure to do so may cause death or serious injury. ●The driver and all passengers in the vehicle must wear their seat belts


properly. The SRS airbags are supplemental devices to be used with the seat belts. ●The SRS driver airbag deploys with considerable force, and can cause


death or serious injury especially if the driver is very close to the airbag. The National Highway Traffic Safety Administration (“NHTSA”) advises: Since the risk zone for the driver’s airbag is the first 2 - 3 in. (50 - 75 mm) of inflation, placing yourself 10 in. (250 mm) from your driver airbag pro- vides you with a clear margin of safety. This distance is measured from the center of the steering wheel to your breastbone. If you sit less than 10 in. (250 mm) away now, you can change your driving position in several ways: • Move your seat to the rear as far as you can while still reaching the


pedals comfortably.


• Slightly recline the back of the seat.


Although vehicle designs vary, many drivers can achieve the 10 in. (250 mm) distance, even with the driver seat all the way forward, sim- ply by reclining the back of the seat somewhat. If reclining the back of your seat makes it hard to see the road, raise yourself by using a firm, non-slippery cushion, or raise the seat if your vehicle has that feature. • If your steering wheel is adjustable, tilt it downward. This points the air-


bag toward your chest instead of your head and neck.


The seat should be adjusted as recommended by NHTSA above, while still maintaining control of the foot pedals, steering wheel, and your view of the instrument panel controls.


92


1


CAUTION


■SRS airbag precautions


1-7. Safety information


●If the seat belt extender has been con- nected to the driver's seat belt buckle but the seat belt extender has not also been fastened to the latch plate of the driver's seat belt, the SRS driver's air- bag system will judge that the driver is wearing the seat belt even though the seat belt has not been connected. In this case, the driver's airbag may not activate correctly in a collision, resulting in death or serious injury in the event of collision. Be sure to wear the seat belt with the seat belt extender.


●The SRS front passenger airbag also deploys with considerable force, and can cause death or serious injury especially if the front passenger is very close to the airbag. The front passenger seat should be as far from the air- bag as possible with the seatback adjusted, so the front passenger sits upright.


●Improperly seated and/or restrained infants and children can be killed or seriously injured by a deploying airbag. An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are the safest for infants and children. (→P. 102)


●Do not sit on the edge of the seat or


lean against the dashboard.


93


1-7. Safety information


CAUTION


■SRS airbag precautions


94


●Do not allow a child to sit on the knees of a front passenger while the vehicle is moving.


●Do not drive the vehicle while the driver or passenger has items resting on their knees.


●Do not lean against the door, the roof side rail or the front, side and rear pil- lars.


●Do not allow anyone to kneel on the passenger seat toward the door or put their head or hands outside the vehicle.


●Do not attach anything to or lean any- thing against areas such as the dash- board, steering wheel pad or lower portion of the instrument panel. These items can become projectiles when SRS driver, front passenger and knee airbags deploy.


1


CAUTION


■SRS airbag precautions


1-7. Safety information


●Do not attach anything to areas such as the door, windshield glass, side door glass, front and rear pillars, roof side rail or assist grip.


●Do not hang coat hangers or other hard objects on the coat hooks. All of these items could become projectiles and seriously injure or kill you, should the SRS curtain shield airbag deploy.


●Vehicles without smart key system: Do not attach any heavy, sharp or hard objects such as keys or accessories to the key. The objects may restrict the SRS knee airbag inflation or be thrust into the driver's seat area by the force of the deploying airbag, thus causing a danger.


●If a vinyl cover is put on the area where the SRS knee airbag will deploy,


be sure to remove it.


●Do not use seat accessories which cover the parts where the SRS side


airbags inflate as they may interfere with inflation of the airbags.


●Do not strike or apply significant levels of force to the area of the SRS air-


bag components (→P. 86). Doing so can cause the SRS airbags to malfunction.


●Do not touch any of the component parts immediately after the SRS air-


bags have deployed (inflated) as they may be hot.


95


1-7. Safety information


CAUTION


■SRS airbag precautions


●If breathing becomes difficult after the SRS airbag has deployed, open a door or window to allow fresh air in, or leave the vehicle if it is safe to do so. Wash off any residue as soon as possible to prevent skin irritation.


●If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillars garnishes, are damaged or cracked, have them replaced by your Toyota dealer.


■Modification and disposal of SRS airbag system components


Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury. ●Installation, removal, disassembly and repair of the SRS airbags. ●Repairs, modifications, removal or replacement of the steering wheel, instrument panel, dashboard, seats or seat upholstery, front, side and rear pillars or roof side rail.


●Repairs or modifications of the front fender, front bumper, or side of the


occupant compartment.


●Installation of snow plows, winches, etc. to the front grille (bull bars, kan-


garoo bar etc.).


●Modifications to the vehicle's suspension system. ●Installation of electronic devices such as mobile two-way radios or CD


players.


●Modifications to your vehicle for a person with a physical disability.


96


1-7. Safety information Front passenger occupant classification system


Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for the front passenger.


SRS warning light “AIR BAG OFF” indicator light “AIR BAG ON” indicator light Front passenger's seat belt reminder light


97


1-7. Safety information


Conditions and operation of the front passenger occupant classification system ■ Adult*1


Indicator/


warning light


“AIR BAG ON” and “AIR BAG OFF” indicator


lights


SRS warning light


“AIR BAG


ON” Off


Front passenger’s seat belt reminder light


Flashing*2


Devices


Front passenger airbag Side airbag on the front


passenger seats


Curtain shield airbag in the front


passenger side


Front passenger’s seat belt pretensioner


■ Child*3 or child restraint system*4


Indicator/


warning light


“AIR BAG ON” and “AIR BAG OFF” indicator


lights


SRS warning light


Front passenger’s seat belt reminder light


Devices


Front passenger airbag Side airbag on the front


passenger seats


Curtain shield airbag in the front


passenger side


Front passenger’s seat belt pretensioner


Activated


“AIR BAG OFF”*5


Off


Flashing*2


Deactivated


Activated


98


1-7. Safety information


■ Unoccupied


Indicator/


warning light


“AIR BAG ON” and “AIR BAG OFF” indicator


lights


Not illuminated


SRS warning light


Front passenger’s seat belt reminder light


Off


Devices


Front passenger airbag Side airbag on the front


passenger seats


Curtain shield airbag in the front


passenger side


Deactivated


Activated


Front passenger’s seat belt pretensioner


Deactivated


■ There is a malfunction in the system


Indicator/


warning light


“AIR BAG ON” and “AIR BAG OFF” indicator


lights


SRS warning light


Front passenger’s seat belt reminder light


Devices


Front passenger airbag Side airbag on the front


passenger seats


Curtain shield airbag in the front


passenger side


Front passenger’s seat belt pretensioner


“AIR BAG


OFF” On Off


Deactivated


Activated


*1: The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may rec- ognize him/her as a child depending on his/her physique and pos- ture. In the event the front passenger does not wear a seat belt.


*2: *3: When a larger child who has outgrown a child restraint system sits in the front passenger seat, the system may recognize him/ her as an adult depending on his/her physique or posture.


99


1-7. Safety information


*4: Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (→P. 102) In case the indicator is not illuminated, consult this manual as for installing the child restraint system properly. (→P. 106)


*5:


CAUTION


■Front passenger occupant classification system precautions


Observe the following precautions regarding the front passenger occupant classification system. Failure to do so may cause death or serious injury. ●Wear the seat belt properly. ●Make sure the front passenger’s seat belt tab has not been left inserted


into the buckle before someone sits in the front passenger seat.


●Make sure the “AIR BAG OFF” indicator light is not illuminated when using the seat belt extender for the front passenger seat. If the “AIR BAG OFF” indicator light is illuminated, disconnect the extender tongue from the seat belt buckle, then reconnect the seat belt. Reconnect the seat belt extender after making sure the “AIR BAG ON” indicator light is illuminated. If you use the seat belt extender while the “AIR BAG OFF” indicator light is illumi- nated, the front passenger airbag, side airbag on the front passenger side airbag may not activate correctly, which could cause death or serious injury in the event of collision.


●Do not apply a heavy load to the front passenger seat or equipment. ●Do not put weight on the front passenger seat by putting your hands or


feet on the front passenger seat seatback from the rear passenger seat.


●Do not let a rear passenger lift the front passenger seat with their feet or


press on the seatback with their legs.


●Do not put objects under the front passenger seat.


100


1


1-7. Safety information


CAUTION


■Front passenger occupant classification system precautions


●Do not recline the front passenger seatback so far that it touches a rear seat. This may cause the “AIR BAG OFF” indicator light to be illuminated, which indicates that the passenger’s airbags will not deploy in the event of a severe accident. If the seatback touches the rear seat, return the seat- back to a position where it does not touch the rear seat. Keep the front passenger seatback as upright as possible when the vehicle is moving. Reclining the seatback excessively may lessen the effectiveness of the seat belt system.


●If an adult sits in the front passenger seat, the “AIR BAG ON” indicator light is illuminated. If the “AIR BAG OFF” indicator is illuminated, ask the passenger to sit up straight, well back in the seat, feet on the floor, and with the seat belt worn correctly. If the “AIR BAG OFF” indicator still remain illuminated, either ask the passenger to move to the rear seat, or if that is not possible, move the front passenger seat fully rearward.


●When it is unavoidable to install the forward-facing child restraint system on the front passenger seat, install the child restraint system on the front passenger seat in the proper order. (→P. 106)


●Do not modify or remove the front seats. ●Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately.


●Child restraint systems installed on the rear seat should not contact the


front seatbacks.


●Do not use a seat accessory, such as a cushion or seat cover, that covers


the seat cushion surface.


●Do not modify or replace the upholstery of the front seat.


101


1-7. Safety information Child restraint systems


A child restraint system for a small child or baby must be properly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of U.S.A. and Canada now require the use of child restraint systems.


Points to remember


Studies have shown that installing a child restraint system on a rear seat is much safer than installing one to the front passenger seat. ● Choose a child restraint system appropriate to the age and size of


the child.


● For installation details, follow the instructions provided with the


child restraint system. General installation instructions are provided in this manual. (→P. 106)


102


1-7. Safety information


Types of child restraints


Child restraint systems are classified into the following 3 types according to the age and size of the child.


Infant seat


Convertible seat


Booster seat


103


1-7. Safety information


■Selecting an appropriate child restraint system


Get an appropriate child restraint system for the child. If a child is too large for a child restraint system, sit the child on a rear seat and use the vehicle's seat belt. (→P. 56)


CAUTION


■Child restraint precautions


●For effective protection in automobile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle's interior. ●Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.


104


1


1-7. Safety information


CAUTION


■Child restraint precautions


●Never install a rear-facing child restraint system on the front passenger seat even if the “AIR BAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child if the rear-facing child restraint system is installed on the front passenger seat.


●A forward-facing child restraint system should be installed on the front passenger seat only when it is unavoidable. Always move the seat as far back as possible even if the “AIR BAG OFF” indicator light is illuminated, because the front passenger airbag could inflate with considerable speed and force. Otherwise, the child may be killed or seriously injured.


●Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of collision.


●Do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front and rear pillars or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side air- bags and curtain shield airbags inflate, and the impact could cause death or serious injury to the child.


●Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly secured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sudden stop or accident.


■When the child restraint system is not in use


●Keep the child restraint system properly secured on the seat even if it is


not in use. Do not store the restraint unsecured in the passenger compartment.


●If it is necessary to detach the child restraint system, remove it from the vehicle or store it securely in the trunk. This will prevent it from injuring passengers in the event of a sudden stop or accident.


105


1-7. Safety information Installing child restraints


Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the rear seats using a seat belt or a child restraint lower anchorage. Attach the top strap when installing a child restraint.


Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt) (→P. 56)


Child restraint ages


lower anchor-


for


the outside


Lower anchorages are pro- vided rear seats. (Buttons displaying the location of the anchorages are attached to the seats.)


Anchor bracket (for top strap) Anchor brackets are provided for all rear seats.


106


1-7. Safety information


Installing child restraints using a seat belt (child restraint lock function belt)


■ Rear facing ⎯ Infant seat/convertible seat STEP 1


Place the child seat on the rear seat facing the rear of the vehi- cle.


STEP 2


STEP 3


Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted.


then allow


Fully extend the shoulder belt and to retract slightly in order to activate the ALR lock mode.


it


Lock mode allows the seat belt to retract only.


107


1-7. Safety information


STEP 4


While pushing the child seat down into the rear seat, allow the shoulder belt to retract until the child seat is securely in place.


After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that in cannot be extended.


■ Forward facing ⎯ Convertible seat STEP 1


Place the child seat on the seat facing the front of the vehicle.


Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted.


it


then allow


Fully extend the shoulder strap and to retract slightly into the ALR lock mode. Lock mode allows the seat belt to retract only.


STEP 2


STEP 3


108


STEP 4


■ Booster seat STEP 1


STEP 2


1-7. Safety information


While pushing the child seat into the rear seat, allow the shoulder belt to retract until the child seat is securely in place.


After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.


Place the booster seat on the seat facing the front of the vehi- cle.


Sit the child in the booster seat. Fit the seat belt to the booster seat according to the manufac- turer's instructions and insert the plate into the buckle. Make sure that the belt is not twisted.


Check that the shoulder belt is correctly positioned over the child's shoulder, and that the lap belt is as low as possible. (→P. 56)


109


1-7. Safety information


Removing a child restraint installed with a seat belt


Push the release button and fully retract the seat belt.


Installation with child restraint lower anchorages


STEP 1


Vehicles with reclining type rear seat: Adjust the seatback to the most upright position.


Type A


STEP 2


STEP 3


Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the anchors. If the child restraint has a top strap, top strap should be latched onto the anchors.


the


For owners in Canada: A symbol on a child restraint sys- tem indicates the presence of a lower connector system.


Canada only


110


1


1-7. Safety information


STEP 2


STEP 3


Widen the gap between the seat cushion and seatback slightly. Latch the buckles onto the anchors. If the child restraint has a top strap, top strap should be latched onto the anchors.


the


For owners in Canada: A symbol on a child restraint sys- tem indicates the presence of a lower connector system.


Type B


Canada only


111


1-7. Safety information


Child restraint systems with a top strap


STEP 1


STEP 2


Secure the child restraint using the seat belt lower anchors, and lock the head restraint in place at the lowest position.


Open the anchor bracket cover, latch the hook onto the anchor bracket and tighten the top strap. is


top strap


Make sure the securely latched.


■Laws and regulations pertaining to anchorages


Anchorages conform to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to confirm to the SAE J1819.


112


1


1-7. Safety information


CAUTION


■When installing a booster seat


Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode: (→P. 59) ●ALR mode causes the belt to tighten only which could cause injury or dis-


comfort to the child.


●Do not allow the child to play with the seat belt or the child could be killed


or seriously injured.


■When installing a child restraint system


Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be seriously injured or even killed in the event of sudden braking or an accident.


●If the driver's seat interferes with the child restraint system and prevents it from being attached correctly, attach the child restraint system to the right- hand rear seat.


●Adjust the front passenger seat so that it does not interfere with the child restraint system.


●Only put a forward-facing or booster child seat on the front seat when unavoidable. When installing a forward- facing or booster child seat on the front passenger seat, move the seat as far back as possible even if the “AIR BAG OFF” indicator light is illuminated. Fail- ing to do so may result in death or seri- ous injury if the airbags deploy (inflate).


113


1-7. Safety information


CAUTION


■When installing a child restraint system


●Vehicles with reclining type rear seat: When installing a child restraint sys- tem in the rear center position, adjust both seatbacks to the most upright position. Otherwise, the child restraint system cannot be securely restrained and this may cause death or serious injuries in a collision.


●When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child's shoulder. The belt should be kept away from the child's neck, but not so that it could fall off the child's shoulder. Failing to do so may result in death or serious injury in the event of an accident or sudden braking.


●Ensure that the belt and tab are securely locked and the seat belt is not


twisted.


●Push and pull the child seat in different directions to be sure it is secure. ●Follow all installation instructions provided by the child restraint system


manufacturer.


■Do not use a seat belt extender


If a seat belt extender is used when installing a child restraint system, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of a colli- sion.


■To correctly attach a child restraint system to the anchorages


When using the lower anchorages, be sure that there are no foreign objects around the anchorages and that the seat belt is not caught behind the child restraint. Make sure the child restraint system is securely attached, or it may cause death or serious injury to the child or other passengers in the event of a sudden stop or accident.


114


2-1. Driving procedures Driving the vehicle


The following procedures should be observed to ensure safe driv- ing. ■ Starting the engine


→P. 126, 130


■ Driving


Automatic transmission


STEP 1


With the brake pedal depressed, shift the shift lever to D.


STEP 2


STEP 3


Release the parking brake.


(→P. 133) (→P. 139) Gradually release the brake pedal and gently depress the accelerator pedal to accelerate the vehicle.


Manual transmission


STEP 1


STEP 2


STEP 3


With the clutch pedal fully depressed, shift the shift lever to 1. (→P. 137) (→P. 139) Release the parking brake. Gradually release the clutch pedal. At the same time, gently depress the accelerator pedal to accelerate the vehicle.


■ Stopping


Automatic transmission


STEP 1


STEP 2


With the shift lever in D, depress the brake pedal. If necessary, set the parking brake. When the vehicle is stopped for an extended period of time, shift the shift lever to P or N. (→P. 133)


Manual transmission


STEP 1


STEP 2


With the clutch pedal fully depressed, depress the brake pedal. If necessary, set the parking brake. When the vehicle is stopped for an extended period of time, shift the shift lever to N. (→P. 137)


116


2


2-1. Driving procedures


■ Parking the vehicle


Automatic transmission


STEP 1


STEP 2


STEP 3


STEP 4


STEP 5


(→P. 139) (→P. 133)


With the shift lever in D, depress the brake pedal. Set the parking brake. Shift the shift lever to P. When parking on a hill, if necessary, block the wheels. Vehicles with smart key system: Turn the “ENGINE START STOP” switch OFF and stop the engine. Vehicles without smart key system: Turn the engine switch to “LOCK” position and stop the engine. Lock the door, making sure that you have the key on your person.


Manual transmission


STEP 1


STEP 2


STEP 3


STEP 4


STEP 5


With the clutch pedal fully depressed, depress the brake pedal. (→P. 139) Set the parking brake. Shift the shift lever to N. (→P. 137) When parking on a hill, shift the shift lever to 1 or R. If necessary, block the wheels. Turn the engine switch to “LOCK” position and stop the engine. Lock the door, making sure that you have the key on your person.


117


2-1. Driving procedures


Starting on a steep uphill


Automatic transmission


STEP 1


STEP 2


STEP 3


Firmly set the parking brake and shift the shift lever to D. Gently depress the accelerator pedal. Release the parking brake.


Manual transmission


STEP 1


STEP 2


STEP 3


With the parking brake firmly set and the clutch pedal fully depressed, shift the shift lever to 1. Lightly depress the accelerator pedal at the same time as gradually releasing the clutch pedal. Release the parking brake.


■Driving in the rain


●Drive carefully when it is raining, because visibility will be reduced, the


windows may become fogged-up, and the road will be slippery.


●Drive carefully when it starts to rain, because the road surface will be


especially slippery.


●Refrain from high speeds when driving on an expressway in the rain, because there may be a layer of water between the tires and the road surface, preventing the steering and brakes from operating properly.


■Breaking in your new Toyota


To extend the life of the vehicle, the following precautions are recommended to observe: ●For the first 186 miles (300 km):


Avoid sudden stops.


●For the first 994 miles (1600 km):


• Do not drive at extremely high speeds. • Avoid sudden acceleration. • Do not drive continuously in the low gears. • Do not drive at a constant speed for extended periods.


118


2-1. Driving procedures


■Drum-in-disc type parking brake system


Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or when- ever the parking brake shoes and/or drum are replaced. Have your Toyota dealer perform the bedding down.


■Operating your vehicle in a foreign country


Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (→P. 430)


■Normal characteristics after turning off the engine


Approximately five hours after the engine is turned off, you may hear sound coming from under the vehicle for several minutes. This is because the fuel evaporation leakage check is performed. It does not indicate a malfunction.


CAUTION


■When starting the vehicle


Vehicles with automatic transmission: Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.


■When driving the vehicle


●Do not drive if you are unfamiliar with the location of the brake and accel-


erator pedals to avoid depressing the wrong pedal. • Accidentally depressing the accelerator pedal instead of the brake pedal will result in sudden acceleration that may lead to an accident that could result in death or serious injury.


• When backing up, you may twist your body around, leading to a diffi- culty in operating the pedals. Make sure to operate the pedals properly. • Make sure to keep a correct driving posture even when moving the vehicle only slightly, allowing you to depress the brake and accelerator pedals properly.


• Depress the brake pedal using your right foot. Depressing the brake pedal using your left foot may delay response in an emergency, result- ing in an accident.


119


2-1. Driving procedures


CAUTION


●Do not drive the vehicle over or stop the vehicle near flammable materials. The exhaust system and exhaust gases can be extremely hot. This may cause a fire if there is any flammable material nearby.


●Vehicles with automatic transmission: Do not let the vehicle roll backwards while the shift lever is in a driving position, or roll forward while the shift lever is in R. Doing so may cause the engine to stall or lead to poor brake and steering performance, resulting in an accident or damage to the vehicle.


●If the smell of exhaust is noticed inside the vehicle, open the windows and check that the trunk is closed. Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immedi- ately.


●Do not under any circumstances shift the shift lever to P or R (automatic transmission vehicles) or R (manual transmission vehicles) while the vehi- cle is moving. Doing so can cause significant damage to the transmission system and may result in a loss of vehicle control.


●Do not shift the shift lever to N while the vehicle is moving.


Doing so may cause insufficient engine braking and lead to an accident.


●Do not turn the engine off while driving.


The power steering and brake booster systems will not operate properly if the engine is not running.


●Use engine braking (downshift) to maintain a safe speed when driving


down a steep hill. Using the brakes continuously may cause the brakes to overheat and lose effectiveness. (→P. 134)


120


2


2-1. Driving procedures


CAUTION


●When stopped on an inclined surface, use the brake pedal and parking brake to prevent the vehicle from rolling backward or forward and causing an accident.


●Do not adjust the position of the steering wheel, the seat, or the inside or


outside rear view mirrors while driving. Doing so may result in a loss of vehicle control that can cause accidents that may result in death or serious injury.


●Always check that all passengers' arms, heads or other parts of their bod- ies are not outside the vehicle, as this may result in death or serious injury. ●Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high- speed capability tires. Driving over 85 mph (140 km/h) may result in tire failure, loss of control and possible injury. Be sure to consult a tire dealer to determine whether the tires on your vehicle are high-speed capability tires or not before driving at such speeds. ■When driving on slippery road surfaces


●Sudden braking, acceleration and steering may cause tire slippage and


reduce your ability to control the vehicle, resulting in an accident.


●Sudden changes in engine speed, such as engine braking caused by up- shifting or down-shifting, may cause the vehicle to skid, resulting in an accident.


●After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly. Wet brake pads may prevent the brakes from functioning properly. If the brakes on only one side are wet and not functioning properly, steering control may be affected, resulting in an accident.


■When shifting the shift lever


Vehicles with an automatic transmission: Be careful not to shift the shift lever with the accelerator pedal depressed. This may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.


121


2-1. Driving procedures


CAUTION


■When the vehicle is stopped


●Do not race the engine.


If the vehicle is in any gear other than P (automatic transmission only) or N the vehicle may accelerate suddenly and unexpectedly, and may cause an accident.


●Do not leave the vehicle with the engine running for a long time.


If such a situation cannot be avoided, park the vehicle in an open space and check that exhaust fumes do not enter the vehicle interior.


●Vehicles with an automatic transmission: Always keep a foot on the brake pedal while the engine is running to prevent an accident caused by the vehicle moving.


■When the vehicle is parked


●Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in


the vehicle when it is in the sun. Doing so may result in the following. • Gas may leak from a cigarette lighter or spray can, and may lead to a


fire.


• The temperature inside the vehicle may cause the plastic lenses and


plastic material of eye glasses to deform or crack.


• Soft drink cans may fracture, causing the contents to spray over the interior of the vehicle, and may also cause a short circuit in the vehi- cle's electrical components.


●Always apply the parking brake, shift the shift lever to P (automatic trans-


mission only), stop the engine and lock the vehicle. Do not leave the vehicle unattended while the engine is running.


●Do not touch the exhaust pipe while the engine is running or immediately


after turning the engine off. Doing so may cause burns.


●Do not leave the engine running in an area with snow build-up, or where it is snowing. If snowbanks build up around the vehicle while the engine is running, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.


122


2


2-1. Driving procedures


CAUTION


■Exhaust gases


Exhaust gases include harmful carbon monoxide (CO) that is colorless and odorless. Inhaling exhaust gases may lead to death or a serious health haz- ard. ●If the vehicle is in a poorly ventilated area, stop the engine. In a closed area, such as a garage, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.


●The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard. ■When taking a nap in the vehicle


Always turn the engine off. Otherwise, you may accidentally move the shift lever or depress the accelerator pedal, which could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly

Loading...
x