2008 Toyota Camry Owners Manual

Rotate the tires in the order shown.

To equalize tire wear and extend tire life, Toyota recom- mends that tire rotation is carried out at the same inter- val as tire inspection.

Front

334

4-3. Do-it-yourself maintenance

Vehicles with a spare tire of the same wheel type as the installed tires

Rotate the tires in the order shown.

To equalize tire wear and extend tire life, Toyota recom- mends that tire rotation is carried out at the same inter- val as tire inspection.

Front

n The tire pressure warning system

Your Toyota is equipped with a tire pressure warning system that uses tire pressure warning valves and transmitters to detect low tire inflation pressure before serious problems arise. (→P. 384) Vehicles with compact spare tire: The compact spare tire is not equipped with the tire pressure warning valve and transmitters.

335

4-3. Do-it-yourself maintenance

Installing tire pressure warning valves and transmitters

When replacing tires or wheels, tire pressure warning valves and transmitters must also be installed. When new tire pressure warning valves and transmitters are installed, new tire pressure warning valve and transmitter ID codes must be registered in the tire pressure warning computer and the tire pressure warning system must be initialized. Have tire pressure warning valve and transmitter ID codes registered by your Toyota dealer. (→P. 337)

Initializing the tire pressure warning system

n The tire pressure warning system must be initialized in the fol-

lowing circumstances:

l When changing the tire inflation pressure by changing traveling

speed or load weight, etc.

l When changing the tire size. When the tire pressure warning system is initialized, the current tire inflation pressure is set as the pressure benchmark. n How to initialize the tire pressure warning system STEP 1

Park the vehicle in a safe place and turn the “ENGINE START STOP” switch or the engine switch OFF. While the vehicle is moving, initialization is not performed. Adjust the tire inflation pressure to the specified cold tire infla- tion pressure level. (→P. 436) Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level. Turn the “ENGINE START STOP” switch to IGNITION ON mode (vehicles with smart key system) or engine switch to “ON” position (vehicles without smart key system).

STEP 2

STEP 3

336

STEP 4

4-3. Do-it-yourself maintenance

Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly 3 times.

STEP 5

Vehicles with smart key system: Wait for a few minutes with the IGNITION ON mode, and then turn the “ENGINE START STOP” switch OFF. Vehicles without smart key system: Wait for a few minutes with the engine switch in “ON” position, and then turn the engine switch to “LOCK” position.

Registering ID codes

The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer.

337

4-3. Do-it-yourself maintenance

n When to replace your vehicle’s tires

Tires should be replaced if: l You have tire damage such as cuts, splits, cracks deep enough to

expose the fabric or bulges indicating internal damage

l A tire goes flat repeatedly or cannot be properly repaired due to the

size or location of a cut or other damage

If you are not sure, consult with your Toyota dealer.

n Replacing tires and wheels

If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After about 20 minutes, the tire pressure warning light comes on after blinking for 1 minute to indicate a system malfunction.

n Tire life

Any tire over 6 years old must be checked by a qualified technician even if it has seldom or never been used or damage is not obvious.

n If the tread wears down 0.16 in. (4 mm) or more on snow tires

The effectiveness of snow tires is lost.

n If you press the tire pressure warning reset switch accidentally

If initialization is performed, adjust the tire inflation pressure to the speci- fied level and initialize the tire pressure warning system again.

338

4-3. Do-it-yourself maintenance

n When the initialization of the tire pressure warning system has

failed Initialization can be completed in a few minutes. However, in the follow- ing cases, the settings has not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. l When operating the tire pressure warning reset switch, the tire pres-

sure warning light does not flash 3 times.

l After driving for a certain period of time since the initialization has been completed, the warning light comes on after blinking for 1
minute.

n Routine tire inflation pressure checks

The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.

n Maximum load of tire

Check that the maximum load of the replaced tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater. For the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire, and for the Gross Axle Weight Ratings (GAWR), see the Certification Label. (→P. 344, 442).

339

4-3. Do-it-yourself maintenance

n Tire types

1 Summer tires

Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads. For driving on snow-covered roads or icy roads, the use of snow tires is recommended. When installing snow tires, be sure to replace all four tires.

2 All season tires

All season tires are designed to provide better traction in snow and to be adequate for driving in most winter conditions, as well as for use year round. All season tires, however, do not have adequate traction performance compared with snow tires in heavy or loose snow. Also, all season tires fall short in acceleration and handling performance compared with summer tires in highway driving.

3 Snow tires

For driving on snow-covered roads or icy roads, we recommend using snow tires. If you need snow tires, select tires of the same size, con- struction and load capacity as the originally installed tires. Since your vehicle has radial tires as original equipment, make sure your snow tires also have radial construction. Do not install studded tires without first checking local regulations for possible restrictions. Snow tires should be installed on all wheels. (→P. 169) n Initializing the tire pressure warning system

Initialize the tires with the tire inflation pressure adjusted to the specified level.

340

4-3. Do-it-yourself maintenance

n Tire pressure warning system certification

For vehicles sold in the U.S.A.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These lim- its are designed to provide reasonable protection against harmful inter- ference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter- mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: l Reorient or relocate the receiving antenna. l Connect the equipment into an outlet on a circuit different from that to

Increase the separation between the equipment and receiver.

which the receiver is connected.

l Consult the dealer or an experienced radio/TV technician for help. FCC WARNING: Changes or modifications not expressly approved by the party responsi- ble for compliance could void the user's authority to operate the equip- ment.

For vehicles sold in Canada

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

341

4-3. Do-it-yourself maintenance

CAUTION

n When inspecting or replacing tires

Observe the following precautions to prevent accidents. Failure to do so may cause damage to parts of the drive train, as well as dangerous handling characteristics, which may lead to fatal accidents or injury. l Do not mix tires of different makes, models, tread patterns or tread-

wear.

l Do not use tire sizes other than those recommended by Toyota. l Do not mix radial, bias-belted, or bias-ply tires. l Do not mix summer, all season and winter tires. l Do not use tires that have been used on another vehicle.

Do not use tires if you do not know how they were used previously.

n When initializing the tire pressure warning system

Do not press the tire pressure warning reset switch without first adjusting the tire inflation pressure to the specified level. Otherwise, the tire pres- sure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually normal.

342

4-3. Do-it-yourself maintenance

NOTICE

n Repairing or replacing tires, wheels and tire pressure warning

valves and transmitters When removing or fitting the wheels, tires or the tire pressure warning valves and transmitters, contact your Toyota dealer as the tire pressure warning valves and transmitters may be damaged if not handled cor- rectly.

n To avoid damaging the tire pressure warning valves and transmit-

ters Do not use liquid sealants on flat tires.

n Driving on rough roads

Take particular care when driving on roads with loose surfaces or pot- holes. These conditions may cause losses in tire air pressure, reducing the cushioning ability of the tires. In addition driving on rough roads may cause damage to the tires themselves, as well as the vehicle’s wheels and body.

n If tire inflation pressures become low while driving

Do not continue driving, or your tires and/or wheels may be ruined.

343

4-3. Do-it-yourself maintenance Tire inflation pressure

n Tire inflation pressure

The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. (→P. 436)

Type A

Type B

344

4-3. Do-it-yourself maintenance

n Inspection and adjustment procedure

Tire valve Tire pressure gauge

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

STEP 6

Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the graduations of the gauge. If the tire inflation pressure is not at the recommended level adjust the pressure. If you add too much air, press the center of the valve to lower. After completing the tire inflation pressure measurement and adjustment, apply soapy water to the valve and check for leakage. Reinstall the tire valve cap.

n Tire inflation pressure check interval

You should check tire inflation pressure every two weeks, or at least once a month. Do not forget to check the spare.

345

4-3. Do-it-yourself maintenance

n Effects of incorrect tire inflation pressure

Driving with incorrect tire inflation pressure may result in the following: l Reduced fuel efficiency l Reduced driving comfort and tire life l Reduced safety l Damage to the drive train If a tire needs frequent refilling, have it checked by your Toyota dealer.

n Instructions for checking tire inflation pressure

When checking tire inflation pressure, observe the following: l Check only when the tires are cold.

If your vehicle has been parked for at least 3 hours and has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.

l Always use a tire pressure gauge.

The appearance of the tire can be misleading. In addition, tire infla- tion pressures that are even just a few pounds off can degrade ride and handling.

l Do not bleed or reduce tire inflation pressure after driving. It is normal

for the tire inflation pressure to be higher after driving.

l Never exceed the vehicle capacity weight.

Passengers and luggage weight should be placed so that the vehicle is balanced.

346

4-3. Do-it-yourself maintenance

CAUTION

n Proper inflation is critical to save tire performance

Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. l Excessive wear l Uneven wear l Poor handling l Possibility of blowouts resulting from overheated tires l Poor sealing of the tire bead l Wheel deformation and/or tire separation l A greater possibility of tire damage from road hazards

NOTICE

n When inspecting and adjusting tire inflation pressure

Be sure to reinstall the tire valve caps. Without the valve caps, dirt or moisture could get into the valve and cause air leakage, which could result in an accident. If the caps have been lost, replace them as soon as possible.

347

4-3. Do-it-yourself maintenance Wheels

If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause loss of handling control. n Wheel selection

When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width, and offset. Replacement wheels are available at your Toyota dealer. Toyota does not recommend using: l Wheels of different sizes or types l Used wheels l Bent wheels that have been straightened

n Aluminum wheel precautions

l Use only Toyota wheel nuts and wrenches designed for use

with your aluminum wheels.

l When rotating, repairing or changing your tires, check that the

wheel nuts are still tight after driving 1000 miles (1600 km).

l Be careful not to damage the aluminum wheels when using

tire chains.

l Use only Toyota genuine balance weights or equivalent and use a plastic or rubber hammer when balancing your wheels.

n When replacing wheels

The wheels of your Toyota are equipped with tire pressure warning valves and transmitters that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure. Whenever wheels are replaced, the tire pressure warning valves and transmitters must be switched over from the old wheels. (→P. 336)

348

4-3. Do-it-yourself maintenance

CAUTION

n When replacing wheels

l Do not use wheels that are a different size from those recommended in

the Owner’s Manual, as this may result in loss of handling control.

l Never use an inner tube in a leaking wheel which is designed for a tubeless tire. Doing so may result in an accident, causing serious injury or death.

NOTICE

n Replacing tire pressure warning valves and transmitters

l Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.

l Ensure that only genuine Toyota wheels are used on your vehicle.

Tire pressure warning valves and transmitters may not work properly with non-genuine wheels.

349

4-3. Do-it-yourself maintenance Air conditioning filter

The air conditioning filter must be cleaned or changed regularly to maintain air conditioning efficiency. n Removal method STEP 1

Vehicles with smart key system: Turn the “ENGINE START STOP” switch OFF. Vehicles without smart key system: Turn the engine switch OFF.

STEP 2

STEP 3

Open the glove box. Slide off the damper.

Apply pressure to the glove box as shown to disconnect the claws.

STEP 4

Remove the filter cover.

350

n Cleaning method

n Replacement method

4-3. Do-it-yourself maintenance

If the filter is dirty, clean by air blowing through the downward side.

compressed from

filter

the

Hold the air gun 2 in. (5 cm) from the filter and blow for approximately 2 minutes at 72
psi (500 kPa, 5.0 kgf/cm2 or bar). If it is not available, have the filter cleaned by your Toyota dealer.

Remove the air conditioning filter and replace it with a new one.

The “↑UP” marks shown on the filter should be pointing up.

n Checking interval

Inspect, clean and replace the air conditioning filter according to the mainte- nance schedule. In dusty areas or areas with heavy traffic flow, more fre- quent cleaning or early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

n If air flow from the vents decreases dramatically

The filter may be clogged. Check the filter and replace if necessary.

351

4-3. Do-it-yourself maintenance

NOTICE

n To prevent damage to the system

l When using the air conditioning system, make sure that a filter is always

installed.

l When cleaning the filter, do not clean the filter with water.

352

4-3. Do-it-yourself maintenance Key battery

Replace the battery with a new one if it is discharged. n You will need the following items:

l Flathead screwdriver (To prevent damage to the key, cover

the tip of the screwdriver with rag.)

l Small Phillips-head screwdriver l Lithium battery CR1632 (vehicles with smart key system), or

CR2016 (vehicles without smart key system)

n Replacing the battery (vehicles with smart key system) STEP 1

Take out the mechanical key.

STEP 2

Remove the cover.

353

4-3. Do-it-yourself maintenance

STEP 3

Remove the depleted battery. Insert a new battery with the “+” terminal facing up.

n Replacing the battery (vehicles without smart key system) STEP 1

Remove the cover.

STEP 2

Remove the module.

354

STEP 3

4-3. Do-it-yourself maintenance

Open the case cover using a coin protected with tape etc. and remove the depleted bat- tery.

Insert a new battery with the “+” terminal facing up.

n If the key battery is discharged

The following symptoms may occur. l The smart key system and wireless remote control will not function prop-

erly.

l The operational range is reduced.

n Use a CR1632 (vehicles with smart key system), or CR2016 (vehicles

without smart key system) lithium battery l Batteries can be purchased at your Toyota dealer, jewelers, or camera

stores.

l Replace only with the same or equivalent type recommended by your

Toyota dealer.

l Dispose of used batteries according to the local laws.

CAUTION

n Removed battery and other parts

Keep away from children. These parts are small and if swallowed by a child they can cause choking.

355

4-3. Do-it-yourself maintenance

NOTICE

n For normal operation after replacing the battery

Observe the following precautions to prevent accidents. l Always work with dry hands.

Moisture may cause the battery to rust.

l Do not touch or move any other components inside the remote control. l Do not bend either of the battery terminals.

356

4-3. Do-it-yourself maintenance Checking and replacing fuses

If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. STEP 1

Vehicles with smart key system: Turn the “ENGINE START STOP” switch OFF. Vehicles without smart key system: Turn the engine switch OFF. Open the fuse box cover.

STEP 2

Engine compartment

Push the tab in and lift the lid off.

Under the driver’s side instrument panel

Remove the lid.

STEP 3

After a system failure, see “Fuse layout and amperage rat- ings” (→P. 360) for details about which fuse to check.

357

4-3. Do-it-yourself maintenance

STEP 4

Remove the fuse with the pull- out tool.

STEP 5

Check if the fuse has blown.

Type A

Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid.

Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid.

Type B

358

Type C

4-3. Do-it-yourself maintenance

Normal fuse Blown fuse Contact your Toyota dealer.

359

4-3. Do-it-yourself maintenance

Fuse layout and amperage ratings

n Engine compartment

Fuse box cover

Fuse block

Fuse SPARE SPARE SPARE

360

Circuit

Ampere

30 A 15 A 10 A

Spare fuse Spare fuse Spare fuse

4-3. Do-it-yourself maintenance

Fuse RR FOG FR DEF AM2
ALT-S

8 MAYDAY/TEL E-ACM 10 ETCS 11 HAZ

12

IG2

13 STR LOCK

14 DOME

15 ECU-B NO.1

16 RADIO NO.1
17 DOOR NO.1
18 AMP

19 EFI MAIN

Ampere

Circuit

10 A 15 A 7.5 A 7.5 A 7.5 A 10 A 10 A 15 A

20 A

20 A

10 A

10 A

15 A 25 A 25 A

30 A

No circuit No circuit Starting system Charging system No circuit No circuit Electronic throttle control system Turn signal lights Multiport fuel injection system/ sequential multiport fuel injection system, starting system, “GAUGE NO.2” and “IGN” fuses Steering lock system Gauges and meters, vanity lights, trunk light, engine switch light, door courtesy lights, interior light, per- sonal lights, clock, smart key sys- tem Wireless remote control system, front passenger occupant classifi- cation system, main body ECU, vehicle stability control system Audio system, navigation system Main body ECU Audio system Multiport fuel injection system/ sequential multiport fuel injection system, electronic throttle control system, “EFI NO.2”, and “EFI NO.3” fuses

361

4-3. Do-it-yourself maintenance

Fuse

Ampere

Circuit

20 EFI NO.3

10 A

21 EFI NO.2

22 S-HORN

23 A/F

24 MPX-B

25 EFI NO.1

26 HORN 27 H-LP(RL) 28 H-LP(LL) 29 H-LP(RH) 30 H-LP(LH) 31 HTR

32 ABS NO.1

33 FAN MAIN

34 ABS NO.2

35 RR DEF

36 RR PWR SEAT

362

15 A

7.5 A

20 A

10 A

10 A

10 A 15 A 15 A 15 A 15 A 50 A

50 A

50 A

30 A

50 A

30 A

Multiport fuel injection system/ sequential multiport fuel injection system Multiport fuel injection system/ sequential multiport fuel injection system Horn Multiport fuel injection system/ sequential multiport fuel injection system Gauges and meters Theft deterrent system, smart key system, multiport fuel injection sys- tem/sequential multiport fuel injec- tion system, electronic throttle control system Horns Right-hand headlight (low beam) Left-hand headlight (low beam) Right-hand headlight (high beam) Left-hand headlight (high beam) Air conditioning system Anti-lock brake system, vehicle sta- bility control system, traction con- trol system, brake assist system Electric cooling fans Anti-lock brake system, vehicle sta- bility control system, traction con- trol system, brake assist system Rear window defogger, “MIR HTR” fuse No circuit

4-3. Do-it-yourself maintenance

Fuse

Ampere

Circuit

37 H-LP CLN 38 CDS FAN 39 RDI FAN 40 MSB

30 A 40 A 40 A 30 A

41 ALT

120 A

42 ST/AM2

30 A

No circuit Electric cooling fans Electric cooling fans No circuit “RR FOG”, “FR DEF”, “HTR”, “ABS NO.1”, “FAN MAIN”, “ABS NO.2”, “RR DEF”, “RR PWR SEAT”, “H- LP CLN”, “CDS FAN”, “RDI FAN” and “MSB” fuses Starting system

363

4-3. Do-it-yourself maintenance

n Under the instrument panel

Fuse

Ampere

Circuit

RR DOOR RH RR DOOR LH FUEL OPN FR FOG

5 OBD

ECU-B NO.2

25 A 25 A 7.5 A 15 A 7.5 A 7.5 A

STOP

10 A

TI&TE

AM1

30 A

7.5 A

364

Rear right power window Rear left power window No circuit Front fog lights On-board diagnosis system No circuit Stop lights, high mounted stop- light, shift lock control system, mul- tiport fuel injection system/ sequential multiport fuel injection system, main body ECU, anti-lock brake system, vehicle stability con- trol system, traction control system, brake assist system, electronic throttle control system No circuit Starting system, multiport fuel injection system/sequential multi- port fuel injection system

4-3. Do-it-yourself maintenance

Fuse

10 A/C 11 PWR 12 DOOR NO.2
13 S/ROOF

Ampere 7.5 A 25 A 25 A 30 A

14 TAIL

15 A

15 PANEL

7.5 A

16 ECU IG NO.1

10 A

17 ECU IG NO.2

7.5 A

18 A/C NO.2

19 WASH 20 S-HTR

21 GAUGE NO.1

22 WIP 23 H-LP LVL

10 A

10 A 20 A

10 A

25 A 7.5 A

Circuit

Air conditioning system Power windows Main body ECU Electric moon roof Front side marker lights, tail lights, rear side marker lights, license plate lights, front turn signal/park- ing lights Navigation system, seat heaters, emergency flashers, air condition- ing system, audio system, clock, glove box light, instrument panel lights, steering switches Main body ECU, electric moon roof, tire pressure warning system, electric cooling fans, auto anti-glare inside rear view mirror Anti-lock brake system, vehicle sta- bility control system, traction con- trol system, brake assist system, shift lock control system, auto- matic transmission, cruise control system Air conditioning system, rear win- dow defogger Windshield wipers and washer Seat heaters Emergency flashers, back-up lights, charging system Windshield wipers and washer No circuit

365

4-3. Do-it-yourself maintenance

Fuse

Ampere

Circuit

24

INJ

15 A

25

IGN

10 A

26 GAUGE NO.2

7.5 A

27 ECU-ACC

28 CIG 29 PWR OUTLET 30 RADIO NO.2
31 MIR HTR 32 POWER 33 P/SEAT

7.5 A

20 A 20 A 7.5 A 10 A 30 A 30 A

Multiport fuel injection system/ sequential multiport fuel injection system, starting system Multiport fuel injection system/ sequential multiport fuel injection system, theft deterrent system, SRS airbag system, steering lock system, front passenger occupant classification system, smart key system, electronic throttle control system Gauges and meters, multi-informa- tion display, clock Clock, main body ECU, shift lock control system, outside rear view mirror, smart key system Power outlet Power outlet Audio system, navigation system Outside rear view mirror defoggers Power windows Power seats

n After a fuse is replaced

If the lights do not turn on even after the fuse has been replaced, a bulb may need replacing. (→P. 368) If the replaced fuse blows again, have the vehicle inspected by your Toyota dealer.

n If there is an overload in the circuits

The fuses are designed to blow before the entire wiring harness is damaged.

366

4-3. Do-it-yourself maintenance

CAUTION

n To prevent system breakdowns and vehicle fire

Observe the following precautions. Failing to do so may cause damage, and possibly a fire or injury. l Never use a fuse of a higher amperage rating than indicated, or use any

other object in place of a fuse.

l Always use a genuine Toyota fuse or equivalent.

Never replace a fuse with a wire, even as a temporary fix. This can cause extensive damage or even fire.

l Do not modify the fuse or the fuse box.

NOTICE

n Before replacing fuses

Have the cause of electrical overload determined and repaired by your Toyota dealer, as soon as possible.

367

4-3. Do-it-yourself maintenance Light bulbs

You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer. n Prepare a replacement light bulb.

Check the wattage of the light bulb being replaced. (→P. 438)

n Remove the engine compartment cover. (3.5 L V6 [2GR-FE]

engine only) →P. 318

n Bulb locations

Headlight high beam

Rear turn signal light

Headlight low beam

Stop/tail and rear side marker light

368

Replacing light bulbs

n Headlight STEP 1

STEP 2

4-3. Do-it-yourself maintenance

Turn the bulb base counterclock- wise.

Headlight (low beam) Headlight (high beam)

Unplug depressing the lock release.

the connector while

Headlight (low beam) Headlight (high beam)

n Rear turn signal, stop/tail and rear side marker lights STEP 1

Open the trunk lid and remove the cover.

369

4-3. Do-it-yourself maintenance

STEP 2

Turn the bulb bases counter- clockwise and remove them.

Rear turn signal light Stop/tail and rear side marker light

n Lights other than the above

If any of the lights listed below has burnt out, have it replaced by your Toyota dealer. l Front fog lights l Front turn signal/parking lights l High mounted stoplight l Front side marker lights l Tail lights l Back-up lights l License plate lights

370

4-3. Do-it-yourself maintenance

n Condensation build-up on the inside of the lens

Contact your Toyota dealer for more information in the following situations. Temporary condensation build-up on the inside of the headlight lens does not indicate a malfunction. l Large drops of water have built up on the inside of the lens. l Water has built up inside the headlight.

n LED high mounted stoplight

The high mounted stoplight consists of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.

CAUTION

n Replacing light bulbs

l Turn off the headlights. Do not attempt to replace the bulb immediately

after turning off the headlights. The bulbs become very hot and may cause burns.

l Do not touch the glass portion of the light bulb with bare hands. Hold the

bulb by the plastic or metal portion. If the bulb is scratched or dropped it may blow out or crack.

l Fully install light bulbs and any parts used to secure them. Failing to do so may result in heat damage, fire, or water entering the headlight unit. This may damage the headlights or cause condensation to build up on the lens.

n To prevent damage or fire

Make sure bulbs are fully seated and locked.

371

4-3. Do-it-yourself maintenance

372

5-1. Essential information If your vehicle needs to be towed

If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws. If towing from the front, the vehicle's rear wheels and axles must be in good condition. (→P. 375) If they are damaged, use a towing dolly or flat bed truck.

Before towing

The following may indicate a problem with your transmission. Contact your Toyota dealer before towing. l The engine is running, but the vehicle will not move. l The vehicle makes an abnormal sound.

374

5-1. Essential information

Towing with a sling-type truck

NOTICE

n To prevent body damage

Do not tow with a sling-type truck, either from the front or rear.

Towing with a wheel-lift type truck from the front

Release the parking brake.

NOTICE

n To prevent damaging the vehicle

When raising the vehicle, ensure adequate ground clearance for towing at the opposite end of the raised vehicle. Without adequate clearance, the vehicle could be damaged while being towed.

375

5-1. Essential information

Towing with a wheel-lift type truck from the rear

the

Automatic transmission: Use a towing dolly under front wheels. Manual transmissions: We rec- ommend to use a towing dolly under the front wheels.

When not using a towing dolly, turn the engine switch to “ACC” position and shift the shift lever to N.

NOTICE

n To prevent causing serious damage to the transmission

(automatic transmission) Never tow this vehicle from the rear with the front wheels on the ground.

n To prevent damaging the vehicle (manual transmission)

Do not tow the vehicle when the engine switch is in “LOCK” position or key removed. The steering lock mechanism is not strong enough to hold the front wheel straight.

Using a flat bed truck

If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45°. Do not overly tighten the tie downs or the vehicle may be damaged.

376

5-1. Essential information If you think something is wrong

If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. n Visible symptoms

l Fluid leaks under the vehicle

(Water dripping from the air conditioning after use is normal.)

l Flat-looking tires or uneven tire wear l Engine coolant temperature gauge needle continually points

higher than normal n Audible symptoms

l Changes in exhaust sound l Excessive tire squeal when cornering l Strange noises related to the suspension system l Pinging or other noises related to the engine

n Operational symptoms

l Engine missing, stumbling or running rough l Appreciable loss of power l Vehicle pulls heavily to one side when braking l Vehicle pulls heavily to one side when driving on a level road l Loss of brake effectiveness, spongy feeling, pedal almost

touches the floor

377

5-1. Essential information Fuel pump shut off system

To minimize the risk of fuel leakage when the engine stalls or an air- bag inflates upon collision, the fuel pump shut off system stops sup- plying fuel to the engine.

Follow the procedure below to restart the engine after the system is activated.

Vehicles with smart key system

STEP 1

STEP 2

Turn the “ENGINE START STOP” switch OFF. Restart the engine.

Vehicles without smart key system

STEP 1

STEP 2

Turn the engine switch to “ACC” or “LOCK” position. Restart the engine.

NOTICE

n Before starting the engine

Inspect the ground under the vehicle. If you find that fuel has leaked on to the ground, the fuel system has been damaged and is in need of repair. Do not restart the engine.

378

5-1. Essential information Event data recorder

Your vehicle has computers that monitor and control certain aspects of your vehicle. These computers assist in driving and maintaining optimal vehicle performance. Besides storing data useful for troubleshooting, there is an event data recorder (EDR) that records data in a crash or a near car crash event.

In a crash or a near car crash event

The SRS airbag sensor assembly contains the EDR. In a crash or a near car crash event, this device may record some or all of the follow- ing information: l Engine speed l Whether the brake pedal was applied or not l Vehicle speed l To what extent the accelerator pedal was depressed l Position of the transmission shift lever l Whether the driver and front passenger wore seat belts or not l Driver's seat position l SRS airbag deployment data l SRS airbag system diagnostic data l Front passenger's occupant classification The information above is intended to be used for the purpose of improving vehicle safety performance. Unlike general data recorders, the EDR does not record sound data such as conversation between passengers.

379

5-1. Essential information

Disclosure of the data

Toyota will not disclose the data recorded in an EDR to a third party except when: l An agreement from the vehicle's owner (or the leasing company for

a leased vehicle) is obtained

l Officially requested by the police or other authorities l Used as a defense for Toyota in a law suit l Ordered by a court law However, if necessary Toyota will: l Use the data for research on Toyota vehicle safety performance l Disclose the data to a third party for research purposes without dis- closing details of the vehicle owner, and only when it is deemed necessary

l Disclose summarized data cleared of vehicle identification informa-

tion to a non-Toyota organization for research purposes

380

5-2. Steps to take in an emergency If a warning light turns on or a warning buzzer sounds...

Calmly perform the following actions if any of the warning lights turn on or flash. If a light turns on or flashes, but then turns off, this does not necessarily indicate a malfunction in the system.

Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous.

The following warning indicates a possible problem in the brake sys- tem. Immediately stop the vehicle in a safe place and contact your Toyota dealer.

Warning light

Warning light/Details

Brake system warning light (warning buzzer)* • Low brake fluid • Malfunction in the brake system This light also comes on when the parking brake is not released. If the light turns off after the parking brake is fully released the system is operating normally.

(U.S.A.)

(Canada)

*: Parking brake engaged warning buzzer: The buzzer sounds to indicate that the parking brake is still engaged (with the vehicle having reached a speed of 3 mph [5 km/h]).

381

5-2. Steps to take in an emergency

Stop the vehicle immediately.

The following warning indicates the possibility of damage to the vehi- cle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer.

Warning light

Warning light/Details

Charging system warning light Indicates a malfunction in the vehicle’s charging system.

Low engine oil pressure warning light (vehicles without multi-information display) Indicates that the engine oil pressure is too low.

Have the vehicle inspected immediately.

Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately.

Warning light

Warning light/Details

(U.S.A.)

(Canada)

Malfunction indicator lamp Indicates a malfunction in: • The electronic engine control system; • The electronic throttle control system; or • The electronic automatic transmission control system.

SRS warning light Indicates a malfunction in: • The SRS airbag system; • The front passenger occupant classification system; or • The seat belt pretensioner system.

382

5-2. Steps to take in an emergency

Warning light

Warning light/Details

ABS warning light Indicates a malfunction in: • ABS; or • The brake assist system.

(U.S.A.)

(Canada)

Vehicle stability control system and traction control system warning light (if equipped) Indicates a malfunction in the VSC system or TRAC sys- tem.

n If the malfunction indicator lamp comes on while driving

First check the following: Is the fuel tank empty? If it is, fill the fuel tank immediately. Is the fuel tank cap loose? If it is, tighten it securely.

The malfunction indicator lamp will go off after taking several driving trips. If the malfunction indicator lamp does not go off even after several trips, con- tact your Toyota dealer as soon as possible.

383

5-2. Steps to take in an emergency

Follow the correction procedures.

After taking the specified steps to correct the suspected problem, check that the warning light turns off.

Warning light

Warning light/Details

Correction procedure

Open door warning light (warning buzzer)*1
Indicates that a door or the trunk is not fully closed. Low fuel level warning light Indicates that remaining fuel is about 2.8 gal. (10.5 L, 2.3 lmp. gal.) or less Driver’s seat belt reminder light (warning buzzer)*2
Warns the driver to fasten his/her seat belt. Front passenger’s seat belt reminder light (warning buzzer)*2
Warns the front passen- ger to fasten his or her seat belt. Low windshield washer fluid warning light (vehi- cles without multi-infor- mation display) Low level of washer fluid

Check that all doors and the trunk are closed.

Refuel the vehicle.

Fasten the seat belt.

Fasten the seat belt.

Fill the tank.

(On the center

panel)

384

Warning light

(U.S.A.)

(U.S.A.)

5-2. Steps to take in an emergency

Correction procedure

Check the engine oil, and change if necessary.

Check and change the engine oil.

Warning light/Details Engine oil replacement reminder light (vehicles without multi-information display) Illuminates for about 3 sec- onds and then flashes for about 15 seconds approxi- mately 4500 miles (7200 km) after the engine oil is changed: Indicates that the engine oil is scheduled to be changed. Comes on and remains on if the distance driven exceeds 5000 miles (8000 km): Indi- cates that the engine oil should be changed. Tire pressure warning light

When the light comes on: Low tire inflation pressure.

Adjust the tire inflation pressure.

When the light comes on after blinking for 1 minute: Malfunction in the tire pressure warning system. Master warning light (vehicles with multi-infor- mation display) A buzzer sounds and the warning light comes on and flashes to indicate that the master warning system has detected a malfunc- tion.

Have the system checked by your Toyota dealer.

→P. 391

385