2004 Toyota Camry Owners Manual

’04Camry_U (L/O 0307)

Fuse locations

Spare fuses

276

Do−it−yourself service precautions If you perform maintenance by yourself, be sure to follow the correct procedure given in this Section. You should be aware that improper or in- complete servicing may result in operating problems. Performing do−it−yourself maintenance during the warranty period may affect your warranty coverage. Read the separate Toyota Warranty statement for details and suggestions. This Section gives for those items that are relatively easy for an owner to perform. As explained in Section 6, there are still a number of items that must be done by a qualified technician with special tools. For information on tools and parts for do− it−yourself maintenance, see “Parts and tools” on page 279 in this Section. Utmost care should be taken when work- ing on your vehicle to prevent accidental injury. Here are a few precautions that you should be especially careful to ob- serve:

instructions only

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

CAUTION

D When the engine is running, keep hands, clothing, and tools away from the moving fan and engine drive rings, watches, and ties is advisable.)

(Removing

belts.

D Right after driving,

the engine compartment—the engine, radiator, exhaust manifold and spark plug boots, etc.—will be hot. So be care- ful not to touch them. Oil, fluids and spark plugs may also be hot. D If the engine is hot, do not remove the radiator cap or loosen the drain plugs to prevent burning yourself.

D Do not

leave anything

that may burn easily, such as paper or rags, in the engine compartment.

D Do not smoke, cause sparks or al- low open flames around fuel or the battery. Their fumes are flammable. D Do not get under your vehicle with just the body jack supporting it. Al- ways use automotive jack stands or other solid supports.

’04Camry_U (L/O 0307)

D Dispose of used oil and filter only in a safe and acceptable manner. Do not dispose of used oil and fil- ter in household trash, in sewers or onto the ground. Call your dealer or a service station information concerning recycling or disposal.

for

D Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on, the electric cooling fans will automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.

D Use eye protection whenever you work on or under your vehicle where you may be exposed to flying or falling material, fluid spray, etc. D Used engine oil contains potentially harmful contaminants which may cause skin disorders such as in- flammation or skin cancer, so care should be taken to avoid prolonged and repeated contact with it. To re- move used engine oil from your skin, wash thoroughly with soap and water.

D Do not

leave used oil within the

reach of children.

D Be extremely cautious when work- ing on the battery. It contains poi- sonous and corrosive sulfuric acid.

277

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Positioning the jack

z Do not drive with the air cleaner filter removed, or excessive engine wear could result. Also backfiring could cause a fire in the engine compartment.

z Be careful not to scratch the glass

surface with the wiper frame.

z When closing

the engine hood, check to see that you have not for- gotten any tools, rags, etc.

Front

Rear

NOTICE

z Remember that battery and ignition cables carry high currents or volt- ages. Be careful of accidentally causing a short circuit.

z Add only “Toyota Super Long Life Coolant” or similar high quality eth- ylene glycol based non−silicate, non−amine, non−nitrite, and non−bo- rate coolant with long−life hybrid organic acid technology to fill the radiator. And if you spill some of the coolant, be sure to wash it off with water to prevent it from dam- aging the parts or paint.

z Do not allow dirt or anything else to fall through the spark plugholes. z Use only spark plugs of the speci- fied type. Using other types will cause engine damage, loss of per- formance or radio noise.

z Do not reuse iridium−tipped spark

plugs by cleaning or regapping.

z Do not overfill automatic transmis- transmission

fluid, or

the

sion could be damaged.

278

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

When jacking up your vehicle with the jack, position jack correctly as shown in the illustrations.

the

CAUTION

When jacking, be sure to observe the following to reduce the possibility of personal injury: D Follow jacking instructions. D Do not put any part of your body under the vehicle supported by the jack. Personal injury may occur.

D Do not start or run the engine while is supported by the

your vehicle jack.

D Never get under the vehicle when the vehicle is supported by the jack alone; use vehicle support stands. D Do not raise the vehicle with some-

one in the vehicle.

D When raising the vehicle, do not place any objects on top of or un- derneath the jack.

NOTICE

Make sure to place the jack correctly, or your vehicle may be damaged.

D Stop the vehicle on a

the transmission

level firm ground, firmly set the parking brake in “P” and put (automatic) or (manual). Block the wheels on the opposite side of the jack up point if neces- sary.

reverse

D Make sure to set the jack properly in the jack point. Raising the ve- hicle with improperly posi- tioned will damage the vehicle or may allow the vehicle to fall off the jack and cause personal injury.

jack

Parts and tools Here is a list of parts and tools you will need to perform do−it−yourself mainte- nance. Remember all Toyota parts are de- signed in metric sizes, so your tools must be metric. CHECKING THE ENGINE OIL LEVEL Parts (if level is low): D “Toyota Genuine Motor Oil” or equiva-

lent See page 282 in Section 7−2 for de- tails about engine oil selection.

Tools: D Rag or paper towel D Funnel (only for adding oil) CHECKING THE ENGINE COOLANT LEVEL Parts (if level is low): D “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−ni- trite, and non−borate coolant with long− life hybrid organic acid technology. “Toyota Super Long Life Coolant” is pre−mixed with 50% coolant and 50% deionized water.

Tools: D Funnel (only for adding coolant)

279

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

CHECKING AND REPLACING FUSES Parts (if replacement is necessary): D Genuine Toyota fuse or equivalent with

same amperage rating as original

ADDING WASHER FLUID Parts: D Water D Washer fluid containing antifreeze (for

winter use)

Tools: D Funnel REPLACING LIGHT BULBS Parts: D Bulb with same number and wattage rating as original (See charts in “Re- placing in Section 7−3.)

light bulbs” on page 301

CHECKING BRAKE FLUID Parts (if level is low): D SAE J1703 or FMVSS No.116 DOT 3

brake fluid

Tools: D Rag or paper towel D Funnel (only for adding fluid) CHECKING POWER STEERING FLUID Parts (if level is low): D Automatic NrII or III

transmission

fluid DEXRO-

Tools: D Rag or paper towel D Funnel (only for adding fluid) CHECKING BATTERY CONDITION Tools: D Warm water D Baking soda D Grease D Conventional wrench

(for

terminal

clamp bolts)

280

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

SECTION 7− 2

DO−IT−YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level Checking the engine coolant level Checking the radiator and condenser Checking brake fluid Checking power steering fluid Checking tire inflation pressure Checking and replacing tires Rotating tires Installing snow tires and chains Replacing wheels Aluminum wheel precautions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

282
284
285
286
286
287
290
292
293
295
295

281

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Checking the engine oil level

Low level

Full level

Low level

Full level

Add oil

O.K.

Too full

Add oil

O.K.

Too full

Type A

Type C

Low level

Full level

With the engine at operating tempera- ture and turned off, check the oil level on the dipstick. 1. To get a

the vehicle should be on a level ground. After turn- ing off the engine, wait a few minutes for the oil to drain back into the bottom of the engine.

reading,

true

Add oil

O.K.

Too full

Type B

282

2. Pull the dipstick out, hold a rag under

the end and wipe it clean.

3. Reinsert the dipstick—push it in as far as it will go, or the reading will not be correct.

4. Pull the dipstick out and look at the oil the

level while holding a rag under end.

CAUTION

Be careful not to touch the hot ex- haust manifold.

NOTICE

Be careful not to drop the engine oil on the vehicle components.

If the oil level is below or only slightly above the low level line, add engine oil of the same type as already in the en- gine. Remove the oil filler cap and add engine oil in small quantities at a time, checking the dipstick. We recommend that you use a funnel when adding oil. The approximate quantity of oil needed to fill between the low level and the full level on the dipstick is indicated below for ref- erence.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Outside temperature

SAE 5W−30 is the best choice for good fuel economy and good starting in cold weather. is not available, SAE If SAE 5W−30 10W−30 may be used. However, it should be replaced with SAE 5W−30 at the next oil change.

API service symbol

When the level reaches within the correct range, install the filler cap hand−tight. Oil quantity, L (qt., lmp. qt.):

2AZ−FE engine 1MZ−FE and 3MZ−FE engines

1.0 (1.1, 0.9)

1.5 (1.6, 1.3)

NOTICE

z Be careful not to spill the engine

oil on the vehicle components.

z Avoid overfilling, or

could be damaged.

the engine

z Check the oil level on the dipstick

once again after adding the oil.

ENGINE OIL SELECTION “Toyota Genuine Motor Oil” in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to grade and viscosity. Oil grade:

following

satisfy

filled

the

is

API grade SL “Energy−Conserving” or ILSAC multigrade engine oil

Recommended viscosity:

SAE 5W−30

ILSAC certification mark

283

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Oil identification marks Either or both API registered marks are added to some oil containers to help you select the oil you should use. The API Service Symbol is located any- where on the outside of the container. The top portion of the label shows the oil quality by API (American Petroleum Insti- tute) designations such as SL. The center portion of the label shows the SAE viscos- ity grade such as SAE 5W−30. “Energy− Conserving” shown in the lower portion, indicates that the oil has fuel−saving ca- pabilities. The ILSAC (International Lubricant Stan- dardization and Approval Committee) Certi- fication Mark is displayed on the front of the container.

284

To ensure excellent lubrication perfor- mance for your engine, “Toyota Genuine Motor Oil” is available, which has been specifically for all Toyota engines. Please contact your Toyota dealer for fur- ther details about “Toyota Genuine Motor Oil”.

tested and approved

type, see “Coolant

Checking the engine coolant level Look at the see−through coolant reser- voir when the engine is cold. The cool- ant level is satisfactory if it is between the “F” and “L” lines on the reservoir. If the level is low, add the coolant. (For the coolant type selection” described below.) The coolant level in the reservoir will vary with engine temperature. However, if the level line, add coolant. Bring the level up to the “F” line. If the coolant level drops within a short time after replenishing, there may be a leak the radiator, hoses, engine coolant filler cap, radiator cap and drain cock and water pump. If you can find no leak, have your Toyota dealer test the cap pressure and check for leaks in the cooling system.

the system. Visually check

is on or below

the “L”

in

CAUTION

To prevent burning yourself, do not remove the radiator cap when the en- gine is hot.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

improper coolants may damage

Coolant type selection Use of your engine cooling system. Only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−nitrite, and non−borate coolant with long−life technology. (Coolant hybrid organic acid with acid technology consists of the combination of low phosphates and organic acids.) “Toyota Super Long Life Coolant” is pre− mixed with 50% coolant and 50% deion- ized water. This coolant provides protec- tion down to about −35_C (−31_F).

long−life

organic

hybrid

NOTICE

Do not use plain water alone.

Toyota recommends “Toyota Super Long Life Coolant” which has been tested to ensure that it will not cause corrosion nor result in malfunction of your engine coolant system with proper usage. “Toyota formulated Super Long Life Coolant” with acid technology and has been specifically designed to avoid engine cooling system malfunction on Toyota vehicles. Please contact your Toyota dealer further details.

is organic

long−life

hybrid

for

Checking the radiator and condenser If any of the above parts are extremely dirty or you are not sure of their condi- tion, take your vehicle to a Toyota dealer.

CAUTION

To prevent burning yourself, be care- ful not to touch the radiator or con- denser when the engine is hot.

NOTICE

To prevent damage to the radiator and condenser, do not perform the work by yourself.

285

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Checking brake fluid

Checking power steering fluid

If the level is low, add SAE J1703 or FMVSS No.116 DOT 3 brake fluid to the brake reservoir. Remove and replace the reservoir cap by hand. Fill the brake fluid to the dotted line. This brings the fluid to the correct level when you put the cap back on. Use only newly opened brake fluid. Once opened, brake fluid absorbs moisture from the air, and excess moisture can cause a dangerous loss of braking.

CAUTION

Take care when filling the reservoir because brake fluid can harm your eyes and damage painted surfaces. If fluid gets in your eyes, flush your eyes with clean water immediately. If you still feel uncomfortable with your eyes, go to the doctor.

NOTICE

If you spill some of the fluid, be sure to wash it off with water to prevent it from damaging the parts or paint.

reservoir. The

To check the fluid level, simply look at the see−through level should be between the “MAX” and “MIN” lines on the reservoir. It is normal for the brake fluid level to go down slightly as the brake pads wear. So be sure to keep the reservoir filled. If the reservoir needs frequent refilling, it may indicate a serious mechanical prob- lem.

286

Close

Open

If hot O.K.

If hot add

If cold O.K.

If cold add

III.

Check the fluid level through the reser- voir. If necessary, add automatic trans- mission fluid DEXRONrII or If the vehicle has been driven around 80
km/h (50 mph) for 20 minutes (a little more in frigid temperatures), the fluid is hot (60_C—80_C or 140_F—175_F). You may also check the level when the fluid is temperature, 10_C—30_C or 50_F—85_F) if the engine has not been run for about five hours.

(about

room

cold

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

Clean all dirt from outside of the reservoir tank and look at the fluid level. If the fluid is cold, the level should be in the “COLD” range. Similarly, if it is hot, the fluid level should be in the “HOT” range. If the level is at the low side of either range, add automatic fluid DEXRONrII or III to bring the level within the range. To remove the reservoir cap, turn it coun- terclockwise and it, turn it clockwise. After replacing the reser- voir cap, visually check the steering box case, vane pump and hose connections for leaks or damage.

lift up. To reinstall

transmission

CAUTION

The reservoir tank may be hot so be careful not to burn yourself.

NOTICE

Avoid overfilling, or the power steer- ing could be damaged.

’04Camry_U (L/O 0307)

Checking tire inflation pressure

Keep your tire inflation pressures at the proper level. The recommended cold tire inflation pressures, tire sizes and the com- bined weight of occupants and cargo (vehicle capacity weight) are de- scribed on page 308 and 312. They are also on the tire and loading infor- mation label. You should check the tire inflation pressure every two weeks, or at least once a month. And do not forget the spare!

287

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

should

pressure

following

instructions

The for checking tire inflation pressure should be observed: D The

be checked only when the tires are cold. If your vehicle has been parked for at least 3 hours and has not been driven for more than 1.5
km or 1 mile since, you will get an accurate cold tire inflation pres- sure reading.

D Always use a tire pressure gauge. The appearance of a tire can be misleading. Besides, tire inflation pressures that are even just a few pounds off can degrade ride and handling.

D Take special care when adding air to the compact spare tire. The smaller tire size can gain pressure very quickly. Add com- pressed air in small quantities and check the pressure often until it reaches the specified pressure.

288

’04Camry_U (L/O 0307)

D Do not bleed or reduce tire inflation pressure after driving. It is normal for the tire inflation pressure to be higher after driving. D Never exceed the vehicle capac- ity weight. The passenger and luggage weight should be located so that the vehicle is balanced.

Tire pressure gauge

INSPECTION AND ADJUSTMENT PROCEDURE 1. Remove the tire valve cap. 2. Press the tip of the tire pressure

gauge to the tire valve.

3. Read the pressure using a gradua-

tion of the gauge.

4. In case that the tire inflation pres- sure is not within the prescribed range, insert the compressed air from the valve. In case of applying too much air, press the center of the valve and release the air to ad- just.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

5. After completing the tire inflation pressure measurement and ad- justment, apply soap water to the valve and check the leakage.

6. Install the tire valve cap. If the gauge and the air pump are not available, have your vehicle checked by your Toyota dealer.

CAUTION

Be sure to reinstall the tire valve caps. Without the valve caps, dirt or moisture could get into the valve core and cause air leakage. If the caps have been lost, have new ones put on as soon as pos- sible.

Incorrect tire inflation pressure may waste fuel, reduce the comfort of driv- ing, reduce tire life and make your ve- hicle less safe to drive. If a tire frequently needs refilling, have it checked by your Toyota deal- er.

CAUTION

Keep your tires properly inflated. Otherwise, the following condi- tions may occur and cause an ac- cident resulting in death or seri- ous injuries. Low tire pressure (underinfla- tion)— D Excessive wear D Uneven wear D Poor handling D Possibility of blowouts from

overheated tire.

D Poor sealing of the tire bead D Wheel deformation and/or tire

separation

D A greater possibility of tire

damage from road hazards

High tire pressure (overinfla- tion)— D Poor handling D Excessive wear D Uneven wear D A greater possibility of tire

damage from road hazards

289

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Checking and replacing tires

Tread wear indicator

CHECKING YOUR TIRES Check the tires tread for the tread wear indicators. If the indicators show, replace the tires. The loca- tion of the tread wear indicators is shown by the “TWI” or “Δ” marks, etc., molded on the sidewall of each tire.

290

The tires on your Toyota have built−in tread wear indicators to help you know when the tires need replace- ment. When the tread depth wears to 1.6 mm (0.06 in.) or less, the indica- tors will appear. If you can see the indicators in two or more adjacent grooves, the tire should be replaced. The lower the tread, the higher the risk of skidding. The effectiveness of snow tires is lost if the tread wears down below 4 mm (0.16 in.). If you have tire damage such as cuts, splits, cracks deep enough to expose the fabric, or bulges indi- cating internal damage, the tire should be replaced. If a tire often goes flat or cannot be properly repaired due to the size or location of a cut or other damage, it should be replaced. If you are not sure, consult with your Toyota dealer.

If an air loss occurs while driving, do not continue driving with a deflated tire. Driving even a short distance can damage a tire beyond repair. Any tires which are over 6 years old must be checked by a qualified technician even if damage is not obvious. Tires deteriorate with age even if they have never or seldom been used. This applies also to the spare tire and tires stored for future use.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

REPLACING YOUR TIRES When replacing a tire, use a tire of the same size and construction, and the same or greater maximum load as the originally installed tires. Using any other size or type of tire may seriously affect handling, ride, speedometer/odometer calibration, ground clearance, and clearance be- tween the body and tires or snow chains. Check that the maximum load of the replaced tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever greater. As for the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire, and as for the Gross Axle Weight Ratings (GAWR), see the Cer- tification Label. For details about the side wall of the tire and the Certification Label, see pages 211 and 208.

’04Camry_U (L/O 0307)

CAUTION

Observe the following instruc- tions. Otherwise, an accident may occur resulting in death or serious injuries. D Do not mix radial, bias belted, or bias−ply tires on your ve- hicle, as this may cause dan- gerous handling characteris- tics resulting in loss of control. D Do not use tires other than the manufacturer’s recommended size, as this may cause danger- ous handling characteristics resulting in loss of control.

Toyota recommends all four tires, or at least both of the front or rear tires be replaced at a time as a set. See “If you have a flat tire” on page 243 for tire change procedure. When a tire is replaced, the wheel should always be balanced. An unbalanced wheel may affect ve- hicle handling and tire life. Wheels can get out of balance with regular use and should therefore be balanced occasionally. When replacing a tubeless tire, the air valve should also be replaced with a new one.

291

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Rotating tires

With a spare tire of the same wheel type as the installed tires

With a spare tire of different wheel type from the installed tires

292

Manual

To equalize the wear and help ex- tend tire life, Toyota recommends that you rotate your tires accord- ing to the maintenance schedule. (For scheduled maintenance infor- mation, please refer to the “Sched- uled Maintenance Guide” or “Own- er’s Supplement”.) However, the most appropriate tim- ing for tire rotation may vary ac- cording to your driving habits and road surface conditions. See “If you have a flat tire” on page 243 in Section 4 for tire change proce- dure. When rotating tires, check for uneven wear and damage. Abnormal wear is usually caused by incorrect tire pres- sure, improper wheel alignment, out− of−balance wheels, or severe braking.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

CAUTION

Do not include a compact spare tire when rotating the tires. It is designed for temporary use only.

’04Camry_U (L/O 0307)

Installing snow tires and chains WHEN TO USE SNOW TIRES OR CHAINS Snow tires or chains are recommended when driving on snow or ice. On wet or dry roads, conventional tires provide better traction than snow tires. SNOW TIRE SELECTION If you need snow tires, select tires of the same size, construction and load capacity as the originally installed tires. Do not use tires other than those men- tioned above. Do not install studded tires without first checking local regulations for possible restrictions.

CAUTION

Do not use snow tires other than the manufacturer’s recommended size, as this may cause dangerous handling characteristics resulting loss of control. Otherwise, an accident may occur resulting in death or serious injuries.

in

SNOW TIRE INSTALLATION Snow tires should be installed on all wheels. Installing snow tires on the front wheels only can lead to an excessive difference in road grip capability between the front and rear tires which could cause loss of vehicle control. When storing removed tires you should store them in a cool dry place. Mark the direction of rotation and be sure to install them in the same direction when replac- ing.

CAUTION

D Do not drive with the snow tires

incorrectly inflated.

D Never drive over 120 km/h (75 mph)

with any type of snow tires.

TIRE CHAIN SELECTION Use the tire chains of correct size. For P205/65R15 tires, use SAE Class “S” type radial tire chains except radial cable chains or V−bar type chains.

293

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Regulations regarding the use of tire chains vary according to location or type of road, so always check the local regulations before installing chains. CHAIN INSTALLATION Install the chains on the front tires as tightly as possible. Do not use tire chains on tires. Retighten chains km after (1/4—1/2 mile). When installing chains on your tires, care- fully follow the instructions of the chain manufacturer. If wheel covers are used, they will be scratched by the chain band, so remove the covers before putting on the chains.

rear driving

0.5—1.0

the

Side chain

Cross chain

For P215/60R16 tires, use the following type chains.

A Diameter of side chain B Width of side chain C Length of side chain D Diameter of cross chain E Width of cross chain F Length of cross chain

mm (in.) 3 (0.12) 10 (0.39) 30 (1.18) 4 (0.16) 14 (0.55) 25 (0.98)

294

CAUTION

D Do not exceed 50 km/h (30 mph) or recom- is

the chain manufacturer’s mended speed lower.

limit, whichever

D Drive carefully avoiding bumps, holes, and sharp turns, which may cause the vehicle to bounce.

D Avoid sharp turns or locked−wheel braking, as use of chains may ad- versely affect vehicle handling.

D When driving with chains installed, to drive carefully. Slow be sure down before entering curves to avoid losing control of the vehicle. Otherwise an accident may occur.

NOTICE

Do not attempt to use a tire chain on the compact spare tire, as it may re- sult in damage to the vehicle as well as the tire.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Replacing wheels WHEN TO REPLACE YOUR WHEELS If you have wheel damage such as bending, cracks or heavy corrosion, the wheel should be replaced. If you fail to replace a damaged wheel, the tire may slip off the wheel or cause loss of handling control. WHEEL SELECTION When replacing wheels, care should be taken to ensure that the wheels are re- placed by ones with the same load ca- pacity, diameter, rim width, and offset. Correct replacement wheels are available at your Toyota dealer. A wheel of a different size or type may adversely affect handling, wheel and bear- ing life, brake cooling, speedometer/odom- eter calibration, stopping ability, headlight aim, bumper height, vehicle ground clear- ance, and tire or snow chain clearance to the body and chassis.

Replacement with used wheels is not rec- ommended as they may have been sub- jected to rough treatment or high mileage and could fail without warning. Also, bent wheels which have been straightened may have structural damage and therefore should not be used. Never use an inner tube in a leaking wheel which is designed for a tubeless tire.

CAUTION

Do not use wheels other than the manufacturer’s recommended size, as this may cause dangerous handling characteristics resulting loss of control. Otherwise, an accident may occur resulting in death or serious injuries.

in

Aluminum wheel precautions D When aluminum wheels, check tight after driving your vehicle the first 1600
km (1000 miles).

the wheel nuts are

installing that

repaired, or D If you have changed your the wheel nuts are still tight after driving 1600 km (1000 miles).

rotated, tires, check

that

D When using tire chains, be careful not

to damage the aluminum wheels.

D Use only the Toyota wheel nuts and for your aluminum

wrench designed wheels.

D When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer.

D As with any wheel, periodically check your aluminum wheels for damage. If damaged, replace immediately.

295

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

296

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

SECTION 7− 3

DO−IT−YOURSELF MAINTENANCE Electrical components Checking battery condition Battery recharging precautions Checking and replacing fuses Adding washer fluid Replacing light bulbs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

298
299
300
301
301

297

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Checking battery condition— —Precautions

CAUTION

BATTERY PRECAUTIONS The battery produces flammable and explosive hydrogen gas. D Do not cause a spark from the bat-

tery with tools.

D Do not smoke or light a match near

the battery.

The electrolyte contains poisonous and corrosive sulfuric acid. D Avoid contact with eyes, skin or

clothes.

D Never ingest electrolyte. D Wear protective safety glasses when

working near the battery.

D Keep children away from the bat-

tery.

D If electrolyte gets on your skin, thoroughly wash the contact area. If you feel pain or burning, get medi- cal attention immediately.

D If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediate- ly take off the exposed clothing and follow the procedure above, if nec- essary.

D If you accidentally swallow electro- lyte, drink a large quantity of water or milk. Follow with milk of magne- sia, beaten raw egg or vegetable oil. Then go immediately for emer- gency help.

EMERGENCY MEASURES D If electrolyte gets

in your eyes, flush your eyes with clean water immediately immediate medical attention. If possible, con- tinue to apply water with a sponge or cloth while en route to the medi- cal office.

and get

298

—Checking battery exterior

Terminals

Ground cable

Hold−down clamp

Check the battery for corroded or loose terminal connections, cracks, or loose hold−down clamp. a. If the battery is corroded, wash it off with a solution of warm water and bak- ing soda. Coat the outside of the termi- nals with grease to prevent further cor- rosion.

b. If the terminal connections are loose, their clamp nuts—but do not

tighten overtighten.

c. Tighten

the hold−down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

—Checking battery condition

NOTICE

Type A

z Be sure the engine and all accesso- ries are off before performing main- tenance.

z When checking the battery, remove the ground cable from the negative terminal (“−” mark) first and rein- stall it last.

z Be careful not to cause a short cir-

cuit with tools.

z Take care no solution gets into the

battery when washing it.

If the battery is disconnected or run down, the moon roof may not operate automatically and the jam protection func- tion will not function correctly after you reconnect, replace or recharge the battery. In any of these cases, you should normal- ize the moon roof. To normalize the moon roof, see “Electric moon roof” on page 34
in Section 1−2.

Green

Dark

Clear or light yellow

Type B

Blue

White

Red

CHECKING BY INDICATOR Check the battery condition by the indi- cator color.

Indicator color

Type A

Type B

Green

Blue

Dark

White

Clear or

light yellow

Red

Condition

Good

Charging necessary. Have battery checked by your Toyota dealer. Have battery checked by your Toyota dealer.

Battery recharging precautions During recharging, the battery is pro- ducing hydrogen gas. Therefore, before recharging: 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.

2. Be sure the power switch on the re- charger the charger cables to the battery and when disconnecting them.

is off when connecting

CAUTION

D Always charge the battery in an un- confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventila- tion.

D Only do a slow charge (5 A or less). Charging at a quicker rate is dangerous. The battery may ex- plode, causing personal injuries.

NOTICE

Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.

299

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Checking and replacing fuses

Type A

Good

Blown

Type B

Good

Blown

Type C

Good

Blown

300

If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced. See “Fuse locations” on page 276 in Sec- tion 7−1 for locations of the fuses. Turn the ignition switch and inoperative component off. Pull a suspected fuse straight out and check it. Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse. See page 313 in Section 8 of this manual for the functions controlled by each circuit.

Type A fuses can be pulled out by the pull−out tool. The location of the pull−out tool is shown in the illustration. If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good. If the fuse has blown, push a new fuse into the clip. Only install a fuse with the amperage rat- ing designated on the fuse box lid. If you do not have a spare fuse, in an emergency you can pull out the “MIR fuse, HTR”, “CIG” or “POWER POINT” which may be dispensable for normal driving, and use it if its amperage rating is the same. If you cannot use one of the same amper- age, use one that is lower, but as close as possible to, the rating. If the amperage is fuse might blow out again but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clip. It is a good idea to purchase a set of spare fuses and keep them in your ve- hicle for emergencies.

that specified,

lower

than

the

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

the new

If fuse immediately blows out, there is a problem with the electrical sys- tem. Have your Toyota dealer correct it as soon as possible.

CAUTION

Never use a fuse with a higher am- perage rating, or any other object, in place of a fuse. This may cause ex- tensive damage and possibly a fire.

Adding washer fluid If any washer does not work or low windshield washer fluid level warning light comes on, the washer tank may be empty. Add washer fluid. You may use plain water as washer fluid. in cold areas where tempera- However, tures freezing point, use fluid containing antifreeze. This washer product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

range below

NOTICE

Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.

following

illustrations show how

Replacing light bulbs— The to gain access to the bulbs. When replacing a bulb, make sure the ignition switch and light switch are off. Use bulbs with the wattage ratings given in the table.

CAUTION

D To prevent burning yourself, do not replace the light bulbs while they are hot.

D Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.

NOTICE

Only use a bulb of the listed type.

301

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

W Type

Light bulbs

Bulb No. —

W Type

Trunk light (type A)

Trunk light (type B)

—

A: HB3 halogen bulbs B: HB4 halogen bulbs C: Wedge base bulbs D: Double end bulbs

the

The inside of the lens of exterior lights such as headlights may temporarily fog up when the lens becomes wet in the rain or in a car wash. This is not a problem because the is caused by fogging temperature difference between the outside and the windshield fogged up in the rain. However, if there is a large drop of water on the inside of the lens, or if there is water pooled light, contact your Toyota dealer.

inside of

inside

lens,

just

like

the

the

Light bulbs

Headlights (high)

Headlights (low)

Front fog lights

Parking, front side marker and front turn signal lights Tail and rear side marker lights Rear turn signal lights Stop/tail lights

Back−up lights

License plate lights

High mounted stoplight Personal lights

Interior light (type A) Interior light (type B) Vanity lights

Glove box light

Bulb No. 9005

9006

9006

60

51

51

3457

30/8

194

3.8

921

18

3057

27/8

921

—

921

—

—

—

—

—

18

18

4.9

1.4

302

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

—Headlights

High beam (inside)

Low beam (outside)

1. Open the hood. Turn the bulb base counterclockwise to the front of the vehicle as shown.

The above illustration indicates left−hand headlight.

2. Unplug the connector while depress-

ing the lock release.

If the connector is tight, wiggle it.

3. Plug in a new bulb into the connec- tor and install it into the mounting hole. is not necessary after replacing Aiming the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.

303

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

—Parking, front side marker and front turn signal lights

—Tail and rear side marker, rear turn signal, back−up and stop/tail lights (type A)

a: Tail and rear side marker light b: Rear turn signal light c: Back−up light d: Stop/tail light

304

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

—Tail and rear side marker, rear turn signal, back−up and stop/tail lights (type B)

—High mounted stoplight

a: Tail and rear side marker light b: Rear turn signal light c: Back−up light d: Stop/tail light

305

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

—Front fog and license plate lights If either the left or right front fog or license plate lights burns out, contact your Toyota dealer.

NOTICE

Do not try to replace the front fog or license plate light bulbs by yourself. You may damage the vehicle.

306

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

SECTION 8

SPECIFICATIONS Specifications Dimensions and weights Engine Fuel Service specifications Tires Fuses

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

308
308
309
309
312
313

307

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Dimensions and weights

Overall length

Overall width

Overall height∗1

Wheelbase

Front tread

Rear tread

Vehicle capacity weight (occupants + luggage)

Towing capacity (trailer weight + cargo weight) ∗1: Unladen vehicle ∗2: With 205/65R15 tires ∗3: With 215/60R16 tires

mm (in.)

mm (in.)

mm (in.)

mm (in.)

mm (in.)

mm (in.)

kg (lb.)

kg (lb.)

4805 (189.2)

1795

1490
1500

(70.7) (58.7)∗2
(59.1)∗3

2720 (107.1)

1545

(60.8)

1535

(60.4)

410

(900)

907 (2000)

Engine Model:

2AZ−FE, 1MZ−FE and 3MZ−FE

Type:

2AZ−FE engine

4 cylinder in line, 4 cycle, gasoline

1MZ−FE and 3MZ−FE engines

6 cylinder V type 4 cycle, gasoline

Bore and stroke, mm (in.):

2AZ−FE engine

88.5 96.0 (3.48 3.78)

1MZ−FE engine

87.5 83.0 (3.44 3.27)

3MZ−FE engine

92.0 83.0 (3.62 3.27)

Displacement, cm3 (cu. in.):

2AZ−FE engine 1MZ−FE engine 3MZ−FE engine

2362 (144.1) 2995 (182.8) 3311 (202.1)

308

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Fuel Fuel type:

2AZ−FE engine

Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher

1MZ−FE and 3MZ−FE engines

Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher. For improved vehicle perfor- mance, the use of premium unleaded gasoline with an Octane Rating of 91
(Research Octane Number 96) or higher is recommended.

Fuel tank capacity, L (gal., Imp. gal.):

70 (18.5, 15.4)

Service specifications ENGINE Valve clearance (engine cold), mm (in.):

2AZ−FE engine

Intake Exhaust

0.19—0.29 (0.007—0.011) 0.30—0.40 (0.012—0.016)

1MZ−FE and 3MZ−FE engines

Intake Exhaust

0.15—0.25 (0.006—0.010) 0.25—0.35 (0.010—0.014)

Spark plug type:

DENSO NGK

SK20R11
IFR6A11

Spark plug gap, mm(in.):

1.1 (0.043)

1MZ−FE and 3MZ−FE engines— Drive Borroughs No.BT−33−73F (used belt), Ibf:

tension measured with gauge

tension

drive

belt

belt

125"10

ENGINE LUBRICATION Oil capacity (drain and refill), L (qt., Imp. qt.):

2AZ−FE engine

With filter Without filter

3.8 (4.0, 3.3) 3.6 (3.8, 3.2)

1MZ−FE and 3MZ−FE engines

With filter Without filter

4.7 (5.0, 4.1) 4.5 (4.8, 4.0) “Toyota Genuine Motor Oil” in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to grade and viscosity. Oil grade:

following

satisfy

filled

the

is

API grade SL “Energy−Conserving” or ILSAC multigrade engine oil

309

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Recommended oil viscosity:

SAE 5W−30

Outside temperature

Please contact your Toyota dealer for fur- ther details.

COOLING SYSTEM Total capacity, L (qt., Imp. qt.):

2AZ−FE engine 1MZ−FE and 3MZ−FE engines

6.2 (6.6, 5.4)

9.2 (9.8, 8.1)

Coolant type:

“Toyota Super Long Life Coolant” is filled in your Toyota vehicle at factory fill. In order to avoid technical problems, only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−nitrite, and non−borate coolant with long−life hybrid organic acid technology. Do not use plain water alone. Please contact your Toyota dealer for further details.

310

BATTERY Open voltage∗ at 20_C (68_F):

12.6—12.8 V 12.2—12.4 V 11.8—12.0 V

Fully charged Half charged Discharged

∗: Voltage that is checked 20 minutes af- ter the key is removed with all the lights turned off Charging rates:

5 A max.

Note: If replacement is necessary, make sure to do so with a battery that meets the same standard as the original. CLUTCH Pedal free play, mm (in.):

5—15 (0.2—0.6)

Fluid type: