2000 Toyota Camry Owners Manual

2. Use a good quality polish and wax. If the finish has become extremely weath- ered, use a car−cleaning polish, fol- lowed by a separate wax. Carefully fol- low the manufacturer’s instructions and precautions. Be sure to polish and wax the chrome trim as well as the paint. the vehicle again when water does not bead but remains on the sur- face in large patches.

3. Wax

NOTICE

Always remove the plastic bumpers if your vehicle is re−painted and placed in a high heat paint waxing booth. High temperatures could damage the bumpers.

Cleaning the interior

CAUTION

D Vehicles with side airbags:

Be careful not to splash water or spill liquid on the floor. This may prevent the side airbags from acti- vating correctly, resulting in serious injury.

D Do not wash the vehicle floor with water, or allow water to get onto the floor when cleaning the vehicle interior or exterior. Water may get into audio components or other electrical components above or un- der the floor carpet (or mat) and cause a malfunction; and it may cause body corrosion.

Vinyl interior The vinyl upholstery may be easily cleaned with a mild soap or detergent and water.

tar: Remove with

Road turpentine or cleaners that are marked safe for painted surfaces.

NOTICE

Do not use organic substances (gaso- line, kerosene, benzine or strong sol- vents), which may be toxic or cause damage.

3. Rinse

thoroughly—dried

can cause streaking. In hot weather you may need to rinse each part right after you wash it.

soap

4. To prevent water spots, dry the vehicle using a clean soft cotton towel. Do not rub or press hard—you might scratch the paint.

Automatic car wash Your vehicle may be washed in an auto- matic car wash, but remember that the paint can be scratched by some type of brushes, unfiltered washing water, or the washing process itself. Scratching reduces paint durability and gloss, especially on darker colors. The manager of the car wash should be able to advise you wheth- er the process is safe for the paint on your vehicle.

208

First vacuum over the upholstery to re- move loose dirt. Then, using a sponge or soft cloth, apply the soap solution to the vinyl. After allowing it to soak in for a few minutes to loosen the dirt, remove the dirt and wipe off the soap with a clean damp cloth. If all the dirt do not come off, re- peat the procedure. Commercial foaming− type vinyl cleaners are also available which work well. Follow the manufacturer’s instructions.

NOTICE

Do not use solvent, thinner, gasoline or window cleaner on the interior.

to

foam−type shampoo

Carpets Use a good clean the carpets. Begin by vacuuming thoroughly to remove as much dirt as possible. Several types of foam cleaners are available; some are in aerosol can sand others are powders or liquids which you mix with water to pro- duce a foam. To shampoo the carpets, use a sponge or brush to apply the foam. Rub in overlapping circles.

’00camry U

Do not apply water—the best results are obtained by keeping the carpet as dry as possible. Read the shampoo instructions and follow them closely. Seat belts The seat belts may be cleaned with mild soap and water or with lukewarm water. Use a cloth or sponge. As you are clean- ing, check the belts for excessive wear, fraying, or cuts.

NOTICE

z Do not use dye or bleach on the

belts—it may weaken them.

z Do not use the belts until they be-

come dry.

Windows The windows may be cleaned with any household window cleaner.

NOTICE

When cleaning the inside of the win- dows, be careful not to scratch or damage the heater wires on the rear window.

Air conditioning control panel, car au- instrument panel, c onsole panel, dio, and switches Use a soft damp cloth for cleaning. Soak a clean soft cloth in water or luke- warm water then lightly w ipe off dirt.

NOTICE

z Do not use organic substances (sol- vents, kerosene, alcohol, g asoline, etc.) or alkaline or acidic solutions. These chemicals can cause discol- oring, staining or peeling of the surface.

z If you use cleaners or polishing agents, make sure their ingredients do not include the substances men- tioned above.

z If you use a liquid car freshener, do not spill the liquid onto the ve- hicle’s interior surfaces. It may con- ingredients mentioned a - tain bove. Immediately clean any spill using the method mentioned above.

the

209

’00camry U

z Mildew may develop on soiled leath- er upholstery. Be especially careful to avoid oil spots. Try to keep your upholstery always clean.

to direct sunlight z Long exposure may cause the leather surface to harden and shrink. Keep your ve- hicle in a shaded area, especially in the summer.

z The interior of your vehicle is apt to heat up on hot summer days, so avoid placing on the upholstery items made of vinyl or plastic or containing wax as these tend to stick to leather when warm.

z Improper cleaning of the leather up- in discolor-

holstery could result ation or staining.

If you have any questions about the cleaning of your Toyota, your local Toyota dealer will be pleased to answer them.

Leather Interior The leather upholstery may be cleaned with neutral detergent for wool. Remove dirt using a soft cloth dampened with 5% solution of neutral detergent for wool. Then thoroughly wipe off all traces of detergent with a clean damp cloth. After cleaning or whenever any part of the leather gets wet, dry with a soft clean cloth. Allow the leather to dry in a venti- lated shaded area.

NOTICE

z If a stain should fail to come out with a neutral detergent, apply a cleaner that does not contain an organic solvent.

z Never use organic substances such as benzine, alcohol or gasoline, o r alkaline or acid solutions for clean- ing these could c ause discoloring.

leather

the

as

z Use of a nylon brush or synthetic fiber cloth, etc. may scratch the fine grained surface of the leather.

210

’00camry U

SECTION 6

VEHICLE MAINTENANCE AND CARE

Maintenance requirements

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

212

General maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

213

Does your vehicle need repairing?

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

215

For scheduled maintenance information, please refer to the separate “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

211

’00camry U

Maintenance requirements Your Toyota vehicle has been designed to for fewer maintenance requirements with longer service intervals to save both your time and money. However, each regular maintenance, as well as day−to−day care, is more important than ever before to en- sure smooth, trouble−free, safe, and eco- nomical drivings. It is the owner’s responsibility to make sure the specified maintenance, including general maintenance service, is performed. Note that both the new vehicle and emis- sion control system warranties specify that proper maintenance and care must be per- formed. See “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supple- ment” for complete warranty information. General maintenance General maintenance items are those day− to−day care practices that are important to your vehicle for proper operation. It is the owner’s responsibility to insure that the general maintenance items are performed regularly. These checks or inspections can be done either by yourself or a qualified technician, or if you prefer, your Toyota dealer will be pleased to do them at a nominal cost.

212

Scheduled maintenance The scheduled maintenance items listed in the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement” are those required to be serviced at regular inter- vals. For details of your maintenance schedule, read the separate “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any replacement parts used for maintenance or for the repair of the emission control system be Toyota supplied. The owner may elect to use non−Toyota supplied parts replacement pur- poses without invalidating the emission control system warranty. However, use of replacement parts which are not of equivalent quality may impair the effec- tiveness of the emission control sys- tems. You may also elect to have mainte- nance, replacement, or repair of the emission control devices and system performed by any automotive repair es- tablishment or individual without invali- dating this warranty. See “Owner’s War- ranty Information Booklet” or “Owner’s Manual Supplement” for complete war- ranty information.

for

Where to go for service? Toyota technicians are well−trained spe- cialists and are kept up to date with the latest service information through technical bulletins, service tips, and in−dealership training programs. They learn to work on Toyotas before they work on your vehicle, rather than while they are working on it. You can be confident that your Toyota dealer’s service department performs the best job to meet the maintenance require- ments on your vehicle—reliably and eco- nomically. Your copy of the repair order is proof that all required maintenance has been per- formed for warranty coverage. And if any problems should arise with your vehicle while under warranty, your Toyota dealer will promptly take care of it. Again, be sure to keep a copy of the repair order for any service performed on your Toyota. What about do−it−yourself maintenance? Many of the maintenance items are easy to do yourself if you have a little mechani- cal ability and a few basic automotive tools. Simple instructions for how to per- form them are presented in Section 7.

If you are a skilled do−it−yourself mechan- ic, the Toyota service manuals are recom- mended. Please be aware that do−it−your- self maintenance can affect your warranty coverage. See “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supple- ment” for the details.

’00camry U

the

items

listed,

General maintenance Listed below are the general maintenance items that should be performed as fre- quently as specified. In addition to check- ing if you notice any unusual noise, smell or vibration, you should investigate the cause or take your vehicle to your Toyota dealer or a quali- fied service shop immediately. It is recom- mended that any problem you notice be brought to the attention of your dealer or the qualified service shop for their advice.

CAUTION

Make these checks only where ade- quate ventilation can be obtained if you run the engine.

to

time

OUTSIDE THE VEHICLE Items listed below should be performed from time, unless otherwise specified. Tire pressure Check the pressure with a gauge every two weeks, or at least once a month. See Section 7−2 for additional information.

for

the nuts

Tire surface and wheel nuts Check the tires carefully for cuts, damage or excessive wear. See Section 7−2 for additional information. When checking the tires, make sure no nuts are missing, and check looseness. Tighten them if necessary. Tire rotation Rotate the tires every 12000 km (7500
miles). See Section 7−2 for additional in- formation. Fluid leaks Check underneath for leaking fuel, oil, wa- ter or other the vehicle has been parked for a while. If you smell fuel fumes or notice any leak, have the cause found and corrected immediately. Doors and engine hood Check that all doors including trunk lid operate smoothly and all latches lock se- curely. Make sure the engine hood sec- ondary latch secures the hood from open- ing when the primary latch is released. INSIDE THE VEHICLE Items listed below should be checked regularly, e.g. while performing periodic services, cleaning the vehicle, etc.

fluid after

213

’00camry U

Accelerator pedal Check the pedal for smooth operation and uneven pedal effort or catching. Clutch pedal Check the pedal for smooth operation. Brake pedal Check the pedal for smooth operation and that the pedal has the proper clearance. Check the brake booster function. Brakes At a safe place, check that the brakes do not pull to one side when applied. Parking brake Check that the lever has the proper travel and that, on a safe incline, your vehicle is held securely with only the parking brake applied. Automatic transmission “Park” mecha- nism Check the lock release button of the se- lector lever for proper and smooth opera- tion. On a safe incline, check that your vehicle is held securely with the selector lever in “P” position and all brakes re- leased.

IN THE ENGINE COMPARTMENT Items listed below should be checked from time to time, e.g. each time when refueling. Washer fluid Make sure there is sufficient fluid in the tank. See Section 7−3 for additional in- formation. Engine coolant level Make sure the coolant level is between the “FULL” and “LOW” lines on the see− through reservoir when the engine is cold. See Section 7−2 for additional information. Battery electrolyte level Make sure the electrolyte level of all bat- tery cells is between upper and lower lev- el lines on the case. Add only distilled water when replenishing. See Section 7−3
for additional information. Brake fluid level Make sure the brake fluid level is correct. See Section 7−2 for additional information. Engine oil level Check the level on the dipstick with the engine turned off and the vehicle parked on a level spot. See Section 7−2 for addi- tional information.

Lights Make sure the headlights, stop lights, tail lights, turn signal lights, and other lights are all working. Check headlight aim. Service reminder indicators and warning buzzers Check that all service reminder indicators and warning buzzers function properly. Steering wheel Be alert for changes in steering condition, such as hard steering or strange noise. Seats Check that all front seat controls such as seat adjusters, seatback recliner, etc. op- erate smoothly and that all latches lock securely in any position. Check that the head restraints move up and down smoothly and that the locks hold securely in any latched position. For folding−down rear seatbacks, check latches lock securely. Seat belts Check that the seat belt system such as buckles, retractors and anchors operate properly and smoothly. Make sure that the belt webbings not cut, frayed, worn or damaged.

that

the

214

Power steering fluid level Check the level through the reservoir. The level should be in the “HOT” or “COLD” range depending on the fluid temperature. See Section 7−2 for additional information. Exhaust system If you notice any change in the sound of the exhaust or smell exhaust fumes, have the cause located and corrected immedi- ately. (See “Engine exhaust cautions” in Section 2.)

’00camry U

tip−offs

for changes

Does your vehicle need repairing? Be on the alert in perfor- mance, sounds, and visual that indicate service is needed. Some impor- tant clues are as follows: D Engine missing, stumbling, or pinging D Appreciable loss of power D Strange engine noises D A leak under the vehicle (however, wa- ter dripping from the air conditioning after use is normal.)

D Change

in exhaust sound (This may indicate a dangerous carbon monoxide leak. Drive with the windows open and have the exhaust system checked im- mediately.)

D Flat−looking tire; excessive tire squeal

when cornering; uneven tire wear

D Vehicle pulls to one side when driving

straight on a level road

D Strange noises related to suspension

movement

D Loss of brake effectiveness; spongy feeling brake or clutch pedal;pedal al- most touches floor; vehicle pulls to one side when braking

D Engine coolant temperature continually

higher than normal

If you notice any of these clues, take your vehicle to your Toyota dealer as soon as possible. It probably needs adjustment or repair.

CAUTION

Do not continue driving with the ve- hicle unchecked. It could result in se- rious vehicle damage and possibly personal injury.

215

’00camry U

216

’00camry U

SECTION 7− 1

DO−IT−YOURSELF MAINTENANCE Introduction Engine compartment overview Fuse locations Do−it−yourself service precautions Parts and tools

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

218
220
221
223

217

’00camry U

Engine compartment overview "5S−FE engine

1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Engine oil filler cap 4. Engine oil level dipstick 5. Brake fluid reservoir 6. Fuse blocks 7. Battery 8. Electric cooling fans 9. Windshield washer fluid tank

218

’00camry U

"1MZ−FE engine

1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Engine oil level dipstick 4. Engine oil filler cap 5. Brake fluid reservoir 6. Fuse blocks 7. Battery 8. Electric cooling fans 9. Windshield washer fluid tank

219

Fuse locations

’00camry U

Spare fuses

Type A

220

With daytime running light system only

Type B

’00camry U

Do−it−yourself service precautions If you perform maintenance by yourself, be sure to follow the correct procedure given in this section. You should be aware that improper or in- complete servicing may result in operating problems. Performing do−it−yourself maintenance during the warranty period may affect your warranty coverage. Read the separate Toyota Warranty statement for details and suggestions. This part gives instructions only for those items that are relatively easy for an owner to perform. As explained in Section 6, there are still a number of items that must be done by a qualified technician with special tools. For information on tools and parts for do− it−yourself maintenance, see “Parts and tools”. Utmost care should be taken when work- ing on your vehicle to prevent accidental injury. Here are a few precautions that you should be especially careful to ob- serve:

CAUTION

D When the engine is running, keep hands, clothing, and tools away from the moving fan and engine drive rings, watches, and ties is advisable.)

(Removing

belts.

D Right after driving,

the engine compartment—the engine, radiator, exhaust manifold and spark plug boots, etc.—will be hot. So be care- ful not to touch them. Oil, fluids and spark plugs may also be hot. D If the engine is hot, do not remove the radiator cap or loosen the drain plugs to prevent burning yourself. D Do not smoke, cause sparks or al- low open flames around fuel or the battery. Their fumes are flammable. D Be extremely cautious when work- ing on the battery. It contains poi- sonous and corrosive sulfuric acid. D Do not get under your vehicle with just the body jack supporting it. Al- ways use automotive jack stands or other solid supports.

221

’00camry U

D Dispose of used oil and filter only in a safe and acceptable manner. Do not dispose of used oil and fil- ter in household trash, in sewers or onto the ground. Call your dealer or a service station information concerning recycling or disposal.

for

NOTICE

z Remember that battery and ignition cables carry high currents or volt- ages. Be careful of accidentally causing a short circuit.

z Add only demineralized or distilled water to fill the radiator. And if you spill some of the coolant, be sure to wash off with water to prevent it from damaging the parts or paint.

z Do not allow dirt or anything else to fall through the spark plugholes. z Use only spark plugs of the speci- fied type. Using other types will cause engine damage, loss of per- formance or radio noise.

z Do not reuse platinum−tipped spark

plugs by cleaning or regapping.

z Do not overfill automatic transmis- transmission

fluid, or

the

sion could be damaged.

z Do not drive with the air cleaner filter removed, or excessive engine wear could result. Also backfiring could cause a fire in the engine compartment.

z Be careful not to scratch the glass

surface with the wiper frame.

z When closing

the engine hood, check to see that you have not for- gotten any tools, rags, etc.

D Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on, the electric cooling fans will automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.

D Use eye protection whenever you work on or under your vehicle where you may be exposed to flying or falling material, fluid spray, etc. D Used engine oil contains potentially harmful contaminants which may cause skin disorders such as in- flammation or skin cancer, so care should be taken to avoid prolonged and repeated contact with it. To re- move used engine oil from your skin, wash thoroughly with soap and water.

D Do not

leave used oil within the

reach of children.

222

Parts and tools Here is a list of parts and tools you will need on performing do−it−yourself mainte- nance. Remember all Toyota parts are de- signed in metric sizes, so your tools must be metric. Checking the engine oil level Parts (if level is low): D Engine API

SJ, “Energy−Conserving” ILSAC multigrade having viscosity proper for your climate

grade or

oil

Tools: D Rag or paper towel D Funnel (only for adding oil) Checking the engine coolant level Parts (if level is low): D “TOYOTA Long Life Coolant” or equiva-

lent See Section 7−2 for details about cool- ant type selection.

D Demineralized or distilled water Tools: D Funnel (only for adding coolant)

’00camry U

Checking brake fluid Parts (if level is low): D SAE J1703 or FMVSS No.116 DOT 3

brake fluid

Tools: D Rag or paper towel D Funnel (only for adding fluid) Checking power steering fluid Parts (if level is low): D Automatic

transmission

DEXRONrII or III

Tools: D Rag or paper towel D Funnel (only for adding fluid) Checking battery condition Tools: D Warm water D Baking soda D Grease D Conventional wrench

(for

clamp bolts)

Checking and replacing fuses Parts (if replacement is necessary): D Genuine Toyota fuse or equivalent with

same amperage rating as original

Adding washer fluid Parts: D Water D Washer fluid containing antifreeze (for

winter use)

Tools: D Funnel Replacing light bulbs Parts: D Bulb with same number and wattage rating as original (See charts in “Re- placing light bulbs” in Section 7−3.)

fluid

Tools: D Screwdriver D Flat−bladed screwdriver

terminal

223

’00camry U

224

’00camry U

SECTION 7− 2

DO−IT−YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level Checking the engine coolant level Checking brake fluid Checking power steering fluid Checking tire pressure Checking and replacing tires Rotating tires Installing snow tires and chains Replacing wheels Aluminum wheel precautions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

226
227
228
229
230
231
232
232
233
234

225

’00camry U

Checking the engine oil level

Low level

Full level

CAUTION

Type A

Type B

Add oil

O.K.

Too full

With the engine at operating tempera- ture and turned off, check the oil level on the dipstick. 1. To get a

the vehicle should be on a level spot. After turning off the engine, wait a few minutes for the oil to drain back into the bottom of the engine.

reading,

true

2. Pull out the dipstick, and wipe it clean

with a rag.

3. Reinsert the dipstick—push it in as far as it will go, or the reading will not be correct.

4. Pull the dipstick out and look at the oil

level on the end.

226

Be careful not to touch the hot ex- haust manifold.

If the oil level is below or only slightly above the low level line, add engine oil of the same type as already in the en- gine. Remove the oil filler cap and add engine oil in small quantities at a time, checking the dipstick. The approximate quantity of oil needed to fill between the low level and the full level on the dipstick is indicated below for ref- erence. When the level reaches within the correct range, install the filler cap hand−tight. Oil quantity, L (qt., lmp. qt.):

5S−FE engine 1MZ−FE engine

0.7 (0.7, 0.6) 1.5 (1.6, 1.3)

NOTICE

z Avoid overfilling, or

the engine

could be damaged.

z Check the oil level on the dipstick

once again after adding the oil.

Engine oil selection Use API grade SJ, “Energy−Conserving” or ILSAC multigrade engine oil. Recommended viscosity (SAE):

for good

SAE 5W−30 is the best choice for your vehicle, fuel economy, and good starting in cold weather. If you use SAE 10W−30 engine oil in extremely low temperatures, the engine may become difficult to start, so SAE 5W−30engine oil is recommended.

’00camry U

Oil identification marks Either or both API registered marks are added to some oil containers to help you select the oil you should use. The API Service Symbol is located any- where on the outside of the container. The top portion of the label shows the oil quality by API (American Petroleum Insti- tute) designations such as SJ. The center portion of the label shows the SAE viscos- ity grade such as SAE 5W−30. “Energy− Conserving” shown in the lower portion, indicates that the oil has fuel−saving ca- pabilities. The ILSAC (International Lubricant Stan- dardization and Approval Committee) Certi- fication Mark is displayed on the front of the container.

API service symbol

ILSAC certification mark

Checking the engine coolant level Look at the see−through coolant reser- voir when the engine is cold. The cool- ant level is satisfactory if it is between the “FULL” and “LOW” lines on the reservoir. If the level is low, add ethyl- ene−glycol type coolant for a proper corrosion protection of aluminum com- ponents. The coolant level in the reservoir will vary with engine temperature. However, if the level is on or below the “LOW” line, add coolant. Bring the level up to the “FULL” line. Always use ethylene−glycol type coolant for a proper corrosion protection of alumi- num components. See information in the next column. If the coolant level drops within a short time after replenishing, there may be a leak the radiator, hoses, engine coolant filler cap, radiator cap and drain cock and water pump. If you can find no leak, have your Toyota dealer test the cap pressure and check for leaks in the cooling system.

the system. Visually check

in

227

’00camry U

We recommend to use 50% solution for your Toyota, to provide protection down to about −35_C (−31_F). When it is extreme- ly cold, to about −50_C (−58_F), 60% solution is rec- ommended. Do not use more than 70% solution for better coolant performance.

to provide protection down

NOTICE

Do not use alcohol type antifreeze or plain water alone.

Checking brake fluid

reservoir. The

To check the fluid level, simply look at the see−through level should be between the “MAX” and “MIN” lines on the reservoir. It is normal for the brake fluid level to go down slightly as the brake pads wear. So be sure to keep the reservoir filled. If the reservoir needs frequent refilling, it may indicate a serious mechanical prob- lem.

CAUTION

To prevent burning yourself, do not remove the radiator cap when the en- gine is hot.

that

to preventing

Coolant type selection Use of improper coolants may damage your engine cooling system. Your coolant must contain ethylene−glycol type coolant for a proper corrosion protection of your engine aluminum contains components. Use “TOYOTA Long Life Coolant” or equivalent. freezing and In addition subsequent damage this type of coolant will also prevent corrosion. Further supplemental inhibitors or additives are neither needed nor recommended. Read the coolant container for information on freeze protection. Follow the manufac- turer’s directions to mix with plain water (preferably demineralized water or distilled water). The total capacity of the cooling system is given in Section 8.

for how much

the engine,

to

228

’00camry U

Checking power steering fluid

Open

If cold O.K.

If cold add

If hot O.K.

Close

If hot add

III.

Check the fluid level through the reser- voir. If necessary, add automatic trans- mission fluid DEXRONrII or If the vehicle has been driven around 80
km/h (50 mph) for 20 minutes (a little more in frigid temperatures), the fluid is hot (60_C—80_C or 140_F—175_F). You may also check the level when the fluid is temperature, 10_C—30_C or 50_F—85_F) if the engine has not been run for about five hours.

(about

room

cold

If the level is low, add SAE J1703 or FMVSS No.116 DOT 3 brake fluid to the brake reservoir. Remove and replace the reservoir cap by hand. Fill the brake fluid to the dotted line. This brings the fluid to the correct level when you put the cap back on. Use only newly opened brake fluid. Once opened, brake fluid absorbs moisture from the air, and excess moisture can cause a dangerous loss of braking.

CAUTION

Take care when filling the reservoir because brake fluid can harm your eyes and damage painted surfaces. If fluid gets in your eyes, flush your eyes with clean water.

NOTICE

If you spill some of the fluid, be sure to wash it off with water to prevent it from damaging the parts or paint.

Clean all dirt from outside of the reservoir tank and look at the fluid level. If the fluid is cold, the level should be in the “COLD” range. Similarly, if it is hot, the fluid level should be in the “HOT” range. If the level is at the low side of either range, add automatic fluid DEXRONrII or III to bring the level within the range. To remove the reservoir cap, turn it coun- terclockwise and it, turn it clockwise. After replacing the reser- voir cap, visually check the steering box case, vane pump and hose connections for leaks or damage.

lift up. To reinstall

transmission

CAUTION

The reservoir tank may be hot so be careful not to burn yourself.

NOTICE

Avoid overfilling, or the power steer- ing could be damaged.

229

’00camry U

Checking tire pressure

Keep your tire pressures at the proper level. The recommended cold tire pressures, tire size and the vehicle capacity weight are given in Section 8. They are also on the tire pressure label as shown. You should check the tire pressures every two weeks, or at least once a month. And don’t forget the spare! Incorrect tire pressure can reduce tire life and make your vehicle less safe to drive.

230

the

results

tire pressure

tire pressure

is excessively

Low in excessive wear, poor handling, reduced fuel econo- my, and the possibility of blowouts from overheated tires. Also, low tire pressure can cause poor sealing of the tire bead. If low, there is the possibility of wheel deforma- tion and/or tire separation. High tire pressure produces a harsh ride, handling problems, excessive wear at the center of the tire tread, and a greater possibility of tire damage from road haz- ards. If a tire frequently needs refilling, have it checked by your Toyota dealer. The following instructions for checking tire pressure should be observed: D The pressure should be checked only when the tires are cold. If your ve- hicle has been parked for at least 3
hours and has not been driven for more than 1.5 km or 1 mile since, you will get an accurate cold tire pressure reading.

D Always use a tire pressure gauge. The appearance of a tire can be mis- leading. Besides, that are even just a few pounds off can degrade handling and ride.

tire pressures

D Do not bleed or reduce tire pressure after driving. It is normal for the tire pressure to be higher after driving.

D Never exceed

the vehicle capacity weight. The passenger and luggage weight should be located so that the vehicle is balanced.

D Be sure to reinstall the tire inflation valve caps. Without the valve caps, dirt or moisture could get into the valve core and cause air leakage. If the caps have been lost, have new ones put on as soon as possible.

’00camry U

Checking and replacing tires

Tread wear indicator

CHECKING YOUR TIRES Check the tires tread for the tread wear indicators. If the indicators show, re- place the tires. The tires on your Toyota have built−in tread wear indicators to help you know when the tires need replacement. When the tread depth wears to 1.6 mm (0.06
in.) or less, the indicators will appear. If you can see the indicators in two or more adjacent grooves, the tire should be re- placed. The lower the tread, the higher the risk of skidding. The effectiveness of snow tires is lost if the tread wears down below 4 mm (0.16 in.).

Check the tires regularly for damage such as cuts, splits and cracks. If any damage is found, consult with a techni- cian and have the tire repaired or re- placed. Even if the damage does not appear seri- ous, a qualified technician should examine the damage. Objects which have pene- trated the tire may have caused internal damage. Any tires which are over 6 years old must be checked by a qualified techni- cian even if damage is not obvious. Tires deteriorate with age even have never or seldom been used. This applies also to the spare tire and tires stored for future use. REPLACING YOUR TIRES When replacing a tire, use only the same size and construction as original- ly installed and with the same or great- er load capacity. Using any other size or type of tire may seriously affect handling, ride, speedome- ter/odometer calibration, ground clearance, and clearance between the body and tires or snow chains.

they

if

CAUTION

D Do not mix radial, bias belted, or bias−ply tires on your vehicle. It can cause dangerous handling char- acteristics, resulting in loss of con- trol.

D Do not use tires or wheels other recom-

the manufacturer’s

than mended size.

tire

Toyota recommends all four tires, or at least both front or rear tires be re- placed as a set. See “If you have a flat tire” in Section 4
for tire change procedure. When a is replaced, should always be balanced. An unbalanced wheel may affect vehicle handling and tire life. Wheels can get out of balance with regular use and should therefore be balanced occasionally. When replacing a tubeless tire, the air valve should also be replaced with a new one.

the wheel

231

’00camry U

To equalize the wear and help extend tire life, Toyota recommends that you rotate your tires approximately every 12000 km (7500 miles). However, the most appropriate timing for tire rotation may vary according to your driving hab- its and road surface conditions. See “If you have a flat tire” in Section 4
for tire change procedure. When for uneven wear and damage. Abnormal wear is usu- ally caused by incorrect tire pressure, im- proper wheel alignment, out−of−balance wheels, or severe braking.

tires, check

rotating

Installing snow tires and chains WHEN TO USE SNOW TIRES OR CHAINS Snow tires or chains are recommended when driving on snow or ice. On wet or dry roads, conventional tires provide better traction than snow tires. SNOW TIRE SELECTION If you need snow tires, select the same size, construction and load capacity as the original tires on your Toyota. Do not use tires other than those men- tioned above. Do not install studded tires without first checking local regulations for possible restrictions. SNOW TIRE INSTALLATION Snow tires should be installed on all wheels. Installing snow tires on the front wheels only can lead to an excessive difference in road grip capability between the front and rear tires which could cause loss of vehicle control. When storing removed tires you should store them in a cool dry place. Mark the direction of rotation and be sure to install them in the same direction when replac- ing.

Rotating tires

With a spare tire of the same wheel type as the installed tires

With a spare tire of different wheel type from the installed tires

232

’00camry U

If wheel covers are used, they will be scratched by the chain band,so remove the covers before putting on the chains.

CAUTION

D Do not exceed 50 km/h (30 mph) or recom- is

the chain manufacturer’s mended speed lower.

limit, whichever

D Drive carefully avoiding bumps, holes, and sharp turns, which may cause the vehicle to bounce.

D Avoid sharp turns or locked−wheel braking, as use of chains may ad- versely affect vehicle handling.

Replacing wheels WHEN TO REPLACE YOUR WHEELS If you have wheel damage such as bending, cracks or heavy corrosion, the wheel should be replaced. If you fail to replace damaged wheels, the tire may slip off the wheel or cause loss of handling control. WHEEL SELECTION When replacing wheels, care should be taken to ensure that the wheels are re- placed by ones with the same load ca- pacity, diameter, rim width, and offset. Correct replacement wheels are available at your Toyota dealer. A wheel of a different size or type may adversely affect handling, wheel and bear- ing life, brake cooling, speedometer/odom- eter calibration, stopping ability, headlight aim, bumper height, vehicle ground clear- ance, and tire or snow chain clearance to the body and chassis.

233

CAUTION

D Do not drive with the snow tires

incorrectly inflated.

D Never drive over 120 km/h (75 mph)

with any type of snow tires.

TIRE CHAIN SELECTION Use the tire chains of correct size and type. Use SAE Class “S” type radial tire chains except radial cable chains or V−bar type chains. Regulations regarding the use of tire chains vary according to location or type of road, so always check them before installing chains. CHAIN INSTALLATION Install the chains on the front tires as tightly as possible. Do not use tire tires. Retighten chains on chains after km (1/4—1/2 mile). When installing chains on your tires, care- fully follow the instructions of the chain manufacturer.

rear driving

0.5—1.0

the

’00camry U

Aluminum wheel precautions D After driving your vehicle the first 1600
km (1000 miles), check that the wheel nuts are tight. repaired, or D If you have changed your the wheel nuts are still tight after driving 1600 km (1000 miles).

rotated, tires, check

that

D When using tire chains, be careful not

to damage the aluminum wheels.

D Use only the Toyota wheel nuts and for your aluminum

wrench designed wheels.

D When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer.

D As with any wheel, periodically check your aluminum wheels for damage. If damaged, replace immediately.

Replacement with used wheels is not rec- ommended as they may have been sub- jected to rough treatment or high mileage and could fail without warning. Also, bent wheels which have been straightened may have structural damage and therefore should not be used. Never use an inner tube in a leaking wheel which is designed for a tubeless tire.

234

’00camry U

SECTION 7− 3

DO−IT−YOURSELF MAINTENANCE Electrical components Checking battery condition Battery recharging precautions Checking and replacing fuses Adding washer fluid Replacing light bulbs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

236
237
238
239
239

235

’00camry U

D If electrolyte gets on your skin, thoroughly wash the contact area. If you feel pain or burning, get medi- cal attention immediately.

D If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediate- ly take off the exposed clothing and follow the procedure above, if nec- essary.

D If you accidentally swallow electro- lyte, drink a large quantity of water or milk. Follow with milk of magne- sia, beaten raw egg or vegetable oil. Then go immediately for emer- gency help.

Checking battery condition— —Precautions

CAUTION

BATTERY PRECAUTIONS The battery produces flammable and explosive hydrogen gas. D Do not cause a spark from the bat-

tery with tools.

D Do not smoke or light a match near

the battery.

The electrolyte contains poisonous and corrosive sulfuric acid. D Avoid contact with eyes, skin or

clothes.

D Never ingest electrolyte. D Wear protective safety glasses when

working near the battery.

D Keep children away from the bat-

tery.

EMERGENCY MEASURES D If electrolyte gets

in your eyes, flush your eyes with clean water immediately immediate medical attention. If possible, con- tinue to apply water with a sponge or cloth while en route to the medi- cal office.

and get

236

—Checking battery exterior

Terminals

Ground cable

Hold−down clamp

Check the battery for corroded or loose terminal connections, cracks, or loose hold−down clamp. a. If the battery is corroded, wash it off with a solution of warm water and bak- ing soda. Coat the outside of the termi- nals with grease to prevent further cor- rosion.

b. If the terminal connections are loose, their clamp nuts—but do not

tighten overtighten.

c. Tighten

the hold−down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.

’00camry U

—Checking battery fluid

NOTICE

Type A

z Be sure the engine and all accesso- ries are off before performing main- tenance.

z When checking the battery, remove the ground cable from the negative terminal (“−” mark) first and rein- stall it last.

z Be careful not to cause a short cir-

cuit with tools.

z Take care no solution gets into the

battery when washing it.

Green

Dark

Clear or light yellow

Type B

Blue

White

Red

CHECKING BY HYDROMETER Check hydrometer color.

the battery condition by

the

Hydrometer color

Type A

Type B

GREEN

BLUE

DARK

WHITE

Condition

Good

Charging necessary. Have battery checked by your Toyota dealer.

CLEAR or LIGHT YELLOW

RED

Have battery checked by your Toyota dealer.

Battery recharging precautions During recharging, the battery is pro- ducing hydrogen gas. Therefore, before recharging: 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.

2. Be sure the power switch on the re- charger the charger cables to the battery and when disconnecting them.

is off when connecting

CAUTION

D Always charge the battery in an un- confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventila- tion.

D Only do a slow charge (5 A or less). Charging at a quicker rate is dangerous. The battery may ex- plode, causing personal injuries.

NOTICE

Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.

237

’00camry U

If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced. See “Fuse locations” in Section 7−1 for locations of the fuses. Turn the ignition switch and inoperative component off. Pull a suspected fuse straight out and check it. Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse. See Section 8 of this manual for the functions controlled by each circuit.

Checking and replacing fuses

Type A

Good

Blown

Type B

Good

Blown

Type C

Good

Blown

238

can

you

Type A fuses can be pulled out by the pull−out tool. The location of the pull−out tool is shown in the illustration. If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good. If the fuse has blown, push a new fuse into the clip. Only install a fuse with the amperage rat- ing designated on the fuse box lid. If you do not have a spare fuse, in an emergency the “A/C” “MIRROR−HEATER”, fuse, which may be dispensable for normal driving, and use it if its amperage rating is the same. If you cannot use one of the same amper- age, use one that is lower,but as close as possible to, the rating. If the amperage is lower than that specified, the fuse might blow out again but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clip. It is a good idea to purchase a set of spare fuses and keep them in your ve- hicle for emergencies.

“DOME” or

pull

out

the new

If fuse immediately blows out, there is a problem with the electrical sys- tem. Have your Toyota dealer correct it as soon as possible.

CAUTION

Never use a fuse with a higher am- perage rating, or any other object, in place of a fuse. This may cause ex- tensive damage and possibly a fire.

’00camry U

Adding washer fluid If any washer does not work or low windshield washer fluid level warning light comes on, the washer tank may be empty. Add washer fluid. You may use plain water as washer fluid. in cold areas where tempera- However, tures freezing point, use fluid containing antifreeze. This washer product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

range below

NOTICE

Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.

following

illustrations show how

Replacing light bulbs— The to gain access to the bulbs. When replacing a bulb, make sure the ignition switch and light switch are off. Use bulbs with the wattage ratings given in the table.

CAUTION

Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.

NOTICE

Only use a bulb of the listed type.

239

’00camry U

A: HB3 halogen bulbs B: HB4 halogen bulbs C: Single end bulbs D: Wedge base bulbs E: Wedge base bulbs (amber) F: Double end bulbs

—Headlights

Low beam

Hi beam

1. Open the hood. Turn the bulb base counterclockwise to the front of the vehicle as shown.

W Type

Light bulbs

Headlights (high)

Headlights (low)

Parking, front side marker and front turn signal lights

Rear side marker lights

Bulb No. 9005

9006

3157
NA

60

51

27/8

194

3.8

3156

or

Rear turn signal lights

3157
Stop and tail lights 3157

Back−up lights

921

License plate lights —

High mounted stoplight Personal light

Interior light

Vanity lights

Glove box light

Trunk light

21CP

—

—

—

—

—

240

27

27/8

18

18

10

10

1.2

3.8

’00camry U

—Parking, front side marker and front turn signal lights

2. Unplug the connector while depress-

ing the lock release.

If the connector is tight, wiggle it.

3. Install a new bulb and connector

into the mounting hole.

Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.

Use a flat−bladed screwdriver. Remove and install the cover clips as shown in the following illustrations.

241

’00camry U

Removing the cover clips

Use a flat−bladed screw driver. To protect the surface, place several sheets of paper over the surface.

Installing the cover clips

242

’00camry U

—Rear side maker, rear turn signal, stop and tail lights

Use a Phillips−head screwdriver. Remove and install the cover clips as shown in the following illustrations.

Removing the cover clips

Installing the cover clips

243

’00camry U

—Stop and tail lights (type A)

a: Rear side marker light b: Rear turn signal light c: Stop and tail light

244

’00camry U

—Back−up lights (type A)

—Stop and tail, and back−up lights (type B)

Use a flat−bladed screwdriver.

Use a Phillips−head screwdriver. Remove and install the cover clips as shown in the following illustrations.

245

’00camry U

—License plate lights

Removing the cover clips

Remove and shown in the following illustrations. Type B—Use a Phillips−head screwdriver.

install the cover clips as

Installing the cover clips

a: Stop and tail light b: Back−up light

246

’00camry U

Removing the cover clips (Type A)

Removing the cover clips (Type B)

Installing the cover clips (Type A)

Installing the cover clips (Type B)

247

’00camry U

—High mounted stoplight

248

’00camry U

SECTION 8

SPECIFICATIONS Dimensions and weight Engine Fuel Service specifications Tires Fuses

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

250
251
251
251
254
255

249

’00camry U

P195/70R14 tire

4790 (188.6)

1780

1416

(70.1) (55.7)∗2

2670 (105.1)

1547

(61.0)

1520

(59.8)

380

(837)

P205/65R15 tire