Login- Download PDF Manual
-
2-1. Driving procedures
CAUTION
■When starting the vehicle
Always keep your foot on the brake pedal while stopped with the engine run- ning. This prevents the vehicle from creeping.
■When driving the vehicle
●Do not drive if you are unfamiliar with the location of the brake and accel-
erator pedals to avoid depressing the wrong pedal. • Accidentally depressing the accelerator pedal instead of the brake pedal will result in sudden acceleration that may lead to an accident that could result in death or serious injury.
• When backing up, you may twist your body around, leading to a diffi- culty in operating the pedals. Make sure to operate the pedals properly. • Make sure to keep a correct driving posture even when moving the vehicle only slightly, allowing you to depress the brake and accelerator pedals properly.
• Depress the brake pedal using your right foot. Depressing the brake pedal using your left foot may delay response in an emergency, result- ing in an accident.
●Do not drive the vehicle over or stop the vehicle near flammable materials. The exhaust system and exhaust gases can be extremely hot. This may cause a fire if there is any flammable material nearby.
●Do not let the vehicle roll backwards while the shift lever is in a driving
position, or roll forward while the shift lever is in “R”. Doing so may cause the engine not to operate or lead to poor brake and steering performance, resulting in an accident or damage to the vehicle.
145
2-1. Driving procedures
CAUTION
■When driving the vehicle
●If the smell of exhaust is noticed inside the vehicle, open the windows and
check that the trunk is closed. Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the cause of the problem inspected immediately.
●Do not shift the shift lever to P while the vehicle is moving.
Doing so can damage the transmission and may result in a loss of vehicle control.
●Do not shift the shift lever to R while the vehicle is moving forward.
Doing so can damage the transmission and may result in a loss of vehicle control.
●Do not shift the shift lever to D while the vehicle is moving backward.
Doing so can damage the transmission and may result in a loss of vehicle control.
●Moving the shift lever to N while the vehicle is moving will disengage the engine from the transmission. Engine braking is not available when N is selected.
●During normal driving, do not turn off the engine. Turning the engine off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so. However, in the event of an emergency, such as if it becomes impossible to stop the vehicle in the normal way: →P. 516
●Use engine braking (downshift) to maintain a safe speed when driving
down a steep hill. Using the brakes continuously may cause the brakes to overheat and lose effectiveness. (→P. 163)
●Be careful when driving on slippery surfaces, as the vehicle may spin or
skid when downshifting, rapidly accelerating, braking or turning.
146
2
2-1. Driving procedures
CAUTION
■When driving the vehicle
●Do not adjust the position of the steering wheel, the seat, or the inside or
outside rear view mirrors while driving. Doing so may result in a loss of vehicle control that can cause accidents that may result in death or serious injury.
●Always check that all passengers’ arms, heads or other parts of their bod- ies are not outside the vehicle, as this may result in death or serious injury. ●Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high speed capability tires. Driving over 85 mph (140 km/h) may result in tire failure, loss of control and possible injury. Be sure to consult a tire dealer to determine whether the tires on your vehicle are high-speed capability tires or not before driving at such speeds. ■When driving on slippery road surfaces
●Sudden braking, acceleration and steering may cause tire slippage and
reduce your ability to control the vehicle, resulting in an accident.
●Sudden changes in engine speed, such as engine braking caused by up- shifting or down-shifting, may cause the vehicle to skid, resulting in an accident.
●After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly. Wet brake pads may prevent the brakes from functioning properly. If the brakes on only one side are wet and not functioning properly, steering control may be affected, resulting in an accident.
147
2-1. Driving procedures
CAUTION
■When shifting the shift lever
Be careful not to shift the shift lever with the accelerator pedal depressed. This may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.
■When the vehicle is stopped
●Do not race the engine.
If the vehicle is in any gear other than “P” or “N” the vehicle may acceler- ate suddenly and unexpectedly, and may cause an accident. ●Do not leave the vehicle with the engine on for a long time.
If such a situation cannot be avoided, park the vehicle in an open space and check that exhaust fumes do not enter the vehicle interior.
●In order to prevent accidents due to the vehicle rolling away, always keep depressing the brake pedal while the engine is running, and apply the parking brake as necessary.
●If the vehicle stopped on an incline, in order to prevent accidents caused by the vehicle rolling forward or backward, always depress the brake pedal and securely apply the parking brake as needed.
●Avoid revving or racing the engine.
Running the engine at high speed while the vehicle is stopped may cause the exhaust system to overheat, which could result in a fire if combustible material is nearby.
148
2
2-1. Driving procedures
CAUTION
■When the vehicle is parked
●Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in
the vehicle when it is in the sun. Failure to do so may result in the following: • Gas may leak from a cigarette lighter or spray can, and may lead to a
fire.
• The temperature inside the vehicle may cause the plastic lenses and
plastic material of eye glasses to deform or crack.
• Soft drink cans may fracture, causing the contents to spray over the interior of the vehicle, and may also cause a short circuit in the vehi- cle’s electrical components.
●Always apply the parking brake, shift the shift lever to “P”, stop the engine
and lock the vehicle. Do not leave the vehicle unattended while the engine is running.
●Do not touch the exhaust pipe while the engine is running or immediately
after turning the engine off. Doing so may cause burns.
●Do not leave the engine running in an area with snow build up, or where it
is snowing, or snow is expected to fall. Exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.
149
2-1. Driving procedures
CAUTION
■Exhaust gases
Exhaust gases include harmful carbon monoxide (CO) that is colorless and odorless. Inhaling exhaust gases may lead to death or a serious health haz- ard. ●If the vehicle is in a poorly ventilated area, stop the engine. In a closed area, such as a garage, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.
●The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard. ■When taking a nap in the vehicle
Always turn the engine off. Otherwise, you may accidentally move the shift lever or press the accelera- tor pedal, which could cause an accident or fire due to abnormal engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a seri- ous health hazard.
150
2-1. Driving procedures
CAUTION
■When braking the vehicle
●When the brakes are wet, drive more cautiously.
Braking distance increases when the brakes are wet, and may cause one side of the vehicle to brake differently than the other side. Also the parking brake may not securely hold the vehicle.
●If the power brake assist function does not operate, do not follow other
vehicles closely and avoid downhill or sharp turns that require making. In this case, braking is still possible, but it will require more force on the pedal than usual. Braking distance may also increase.
●Do not pump the brake pedal if the engine stalls.
Each push on the pedal uses up the reserve for the power-assisted brakes.
●The brake system consists of 2 individual hydraulic systems: if one of the systems fails, the other will still operate. In this case, the brake pedal should be depressed more firmly than usual and braking distance becomes longer. Do not drive your vehicle with only a single brake system. Have your brakes fixed immediately.
NOTICE
■While driving the vehicle
●Do not depress the accelerator and brake pedals at the same time during driving. If the brake pedal is depressed while driving with the accelerator pedal depressed, driving torque may be restrained.
●Do not use the accelerator pedal or depress accelerator and brake pedals
at the same time to hold the vehicle on a hill.
151
2-1. Driving procedures
NOTICE
■When parking the vehicle
Always put the shift lever in “P”. Failure to do so may cause the vehicle to move or the vehicle may accelerate suddenly if the accelerator pedal is acci- dentally depressed.
■Avoiding damage to vehicle parts
●Do not turn the steering wheel fully in either direction and hold it there for a
long time. Doing so may damage the power steering pump.
●When driving over bumps in the road, drive as slowly as possible to avoid
damaging the wheels, underside of the vehicle, etc.
■If you hear a squealing or scraping noise (brake pad wear limit indica-
tors) Have your Toyota dealer check and replace the brake pads as soon as pos- sible. The rotor damage can result if the pads are not replaced when needed.
■If you get a flat tire while driving
A flat or damaged tire may cause the following situations. Hold the steering wheel firmly and gradually press the brake pedal to slow down the vehicle. ●It may be difficult to control your vehicle. ●The vehicle will make abnormal sounds. ●The vehicle will behave abnormally. Replace a flat tire with a new one. (→P. 493)
■If the vehicle becomes stuck or bogged
Do not spin the wheels recklessly when any of the tires is up in the air, or stuck in sand or mud, etc. This may damage the drive system components or propel the vehicle forward (or in another direction) and cause an accident.
152
2
2-1. Driving procedures
NOTICE
■When encountering flooded roads
Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehicle. ●Engine stalling ●Short in electrical components ●Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. ●Brake function ●Changes in quantity and quality of oil and fluid used for the engine, trans-
mission, differentials, etc.
●Lubricant condition for the bearings and suspension joints (where possi-
ble) and the function of all joints, bearings, etc.
153
2-1. Driving procedures Engine (ignition) switch (with smart key system)
Performing the following operations when carrying the electronic key on your person starts the engine or changes “ENGINE START STOP” switch modes. ■ Starting the engine STEP 1
Check that the parking brake is set. Check that the shift lever is set in “P”. Sit in the driver’s seat and firmly depress the brake pedal. The “ENGINE START STOP” switch indicator turns green.
Press the “ENGINE START STOP” switch.
The engine can be started from any “ENGINE START STOP” switch mode.
STEP 2
STEP 3
STEP 4
154
2
2-1. Driving procedures
■ Changing engine (ignition) switch mode
Modes can be changed by pressing the “ENGINE START STOP” switch with the brake pedal released. (The mode changes each time the switch is pressed.) OFF* Emergency flashers can be used. ACCESSORY mode Some electrical components such as the audio system can be used. The “ENGINE START STOP” switch indicator turns amber. IGNITION ON mode All electrical components can be used. The “ENGINE START STOP” switch indicator turns amber.
*:If the shift lever is in a position other than “P” when turning off the engine, “ENGINE START STOP” switch will be turned to ACCESSORY mode, not to OFF.
the
155
2-1. Driving procedures
■When the steering lock cannot be released
The green indicator light on the “ENGINE START STOP” switch will flash. Press the “ENGINE START STOP” switch again while turning the steering wheel slightly in either direction.
■If the engine does not start
The engine immobilizer system may not have been deactivated. (→P. 96) ■When the “ENGINE START STOP” switch indicator flashes in amber
The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately. ■Auto power OFF function
The “ENGINE START STOP” switch will automatically turn OFF when left in ACCESSORY mode for 1 hour or more.
■Electronic key battery depletion
→P. 36
■When the electronic key battery is discharged
→P. 440
■Conditions affecting operation
→P. 34
156
2
2-1. Driving procedures
CAUTION
■When starting the engine
Always start the engine while sitting in the driver’s seat. Do not press the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.
■Stopping the engine in an emergency
If you want to stop the engine in an emergency while driving the vehicle, press and hold the “ENGINE START STOP” switch for more than 3 seconds, or press it briefly 3 times or more in succession. However, do not touch the “ENGINE START STOP” switch while driving except in an emergency. Turning the engine off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so.
NOTICE
■To prevent battery discharge
Do not leave the “ENGINE START STOP” switch in ACCESSORY or IGNI- TION ON mode for long periods if the engine is not running.
■When starting the engine
●Do not race the engine. ●If the engine becomes difficult to start or stalls frequently, have the engine
checked immediately.
157
2-1. Driving procedures Engine (ignition) switch (without smart key system)
■ Starting the engine STEP 1
STEP 2
STEP 3
STEP 4
Check that the parking brake is set. Check that the shift lever is set in “P”. Sit in the driver’s seat and firmly depress the brake pedal. Turn the engine switch to the “START” position and start the engine.
■ Engine (ignition) switch
“LOCK” The steering wheel is locked and the key can be removed. (The key can be removed only when the shift lever is in “P”.) “ACC” Some electrical components such as the audio system can be used. “ON” All electrical components can be used. “START” For starting the engine.
158
2-1. Driving procedures
■Turning the key from “ACC” to “LOCK”
STEP 1
Shift the shift lever to “P”.
STEP 2
Push in the key and turn to the “LOCK” position.
■When the steering lock cannot be released
When starting the engine, the engine switch may seem stuck in the “LOCK” position. To free it, turn the key while turn- ing the steering wheel slightly in either direction.
■If the engine does not start
The engine immobilizer system may not have been deactivated. (→P. 96)
■Key reminder function
A buzzer sounds if the driver’s door is opened, while the engine switch is in the “ACC” or “LOCK” position to remind you to remove the key.
159
2-1. Driving procedures
CAUTION
■When starting the engine
Always start the engine while sitting in the driver’s seat. Do not press the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.
■While driving
Do not turn the engine switch to the “LOCK” position. If in an emergency, you must turn the engine off while the vehicle is moving, turn the key only to the “ACC” position.
NOTICE
■To prevent battery discharge
Do not leave the key in the “ACC” or “ON” position for long periods without the engine running.
■When starting the engine
●Do not crank for more than 30 seconds at a time. This may overheat the
starter and wiring systems. ●Do not race the cold engine. ●If the engine becomes difficult to start or stalls frequently, have the engine
checked immediately.
160
2-1. Driving procedures Automatic transmission
Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever
S mode driving position
Vehicles with smart key system: While the “ENGINE START STOP” switch is in IGNITION ON mode, depress the brake pedal and move the shift lever. Vehicles without smart key system: While the engine switch is in the “ON” position, depress the brake pedal and move the shift lever.
161
2-1. Driving procedures
■ Shift position uses
Shift position
Function
Parking the vehicle or starting the engine
Reversing Neutral
Normal driving*1
S mode driving *2*1: Shifting to the D position allows the system to select a gear suitable for
the driving conditions. Setting the shift lever to the D position is recommended for normal driv- ing.
*2: Selecting shift ranges using S mode restricts the upper limit of the pos- sible gear ranges, controls engine braking forces, and prevents unnec- essary upshifting.
162
2-1. Driving procedures
Changing shift ranges in S mode
Shift the shift lever to the S mode driving position and operate the shift lever.
Upshifting Downshifting
The initial shift range in S mode is set automatically to 5 or 4 accord- ing to vehicle speed. However, the initial shift range may be set to 3 if AI-SHIFT has operated while the shift lever was in the D position. (→P. 164)
163
2-1. Driving procedures
■ Shift ranges and their functions
● Automatically selecting gears between 1 and 6 according to vehicle speed and driving condition. (However the gear is limited according to selected shift range.)
● You can choose from 6 levels of engine braking force. ● A lower shift range will provide greater engine braking force than
a higher shift range, and the engine speed will also increase.
■S mode
●When the shift range is 5 or lower, holding the shift lever toward “+” sets
the shift range to 6.
●To prevent excessive engine speed, a function was adopted that auto- matically selects a higher shift range before engine speed becomes too high.
●To protect the automatic transmission, a function is adopted that auto- matically selects a higher shift range when the fluid temperature is high.
■Down shifting restrictions warning buzzer (in the S mode)
To help ensure safety and driving performance, downshifting operation may sometimes be restricted. In some circumstances, downshifting may not be possible even when the shift lever is operated. (The warning buzzer will sound twice.)
■When driving with the cruise control system
Engine braking will not occur in the S mode, even when downshifting to 5 or 4. (→P. 194)
■If the shift lever cannot be shifted from P
→P. 503
164
2-1. Driving procedures
■If the S indicator does not come on even after shifting the shift lever to
S mode driving position This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the transmission will operate in the same manner as when the shift lever is in D.)
■AI-SHIFT
AI-SHIFT automatically selects the suitable gear according to driver perfor- mance and driving conditions. AI-SHIFT automatically operates when the shift lever is in the D position. (Shifting the shift lever to the S mode driving position cancels the function.)
165
2-1. Driving procedures Turn signal lever
Right turn Left turn Move and hold the lever partway to signal a lane change The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change The left hand signal will flash until you release the lever.
■Turn signals can be operated when
Vehicles with smart key system
The “ENGINE START STOP” switch is in IGNITION ON mode.
Vehicles without smart key system
The engine switch is in the “ON” position. ■If the indicators flash faster than usual
Check that a light bulb in the front or rear turn signal lights has not burned out.
166
2-1. Driving procedures Parking brake
U.S.A.
Canada
Sets the parking brake* (Depressing the pedal again releases the parking brake.)
*: Fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot.
■Usage in winter time
See “Winter driving tips” for parking brake usage in winter time. (→P. 219)
NOTICE
■Before driving
Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.
167
2-1. Driving procedures Horn
To sound the horn, press on or close to the
mark.
168
2-2. Instrument cluster Gauges and meters
The units used on the speedometer may differ depending on the target region.
Engine coolant temperature gauge Displays the engine coolant temperature. Tachometer Displays the engine speed in revolutions per minute. Shift position indicator Displays the shift position Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Low fuel level warning light →P. 482
Odometer/trip meter and trip meter reset button →P. 170169
2-2. Instrument cluster
Odometer/Trip meter display
Odometer Displays the total distance the vehicle has been driven. Trip meter Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and dis- play different distances independently.
Multi-information display →P. 175
Odometer and trip meter display button
Vehicles with smart key system
Pressing this button switches among odometer and trip meter when the “ENGINE START STOP” switch is IGNITION ON mode.
Vehicles without smart key system
Pressing this button switches among odometer and trip meter when the engine switch is in the “ON” position.
Odometer Trip meter A Trip meter B Pushing and holding the button will reset the trip meter.
170
2-2. Instrument cluster
Instrument panel light control
The brightness of the instrument panel lights can be adjusted.
Darker Brighter
NOTICE
■To prevent damage to the engine and its components
●Do not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
●The engine may be overheating if the temperature gauge is in the red zone (“H”). In this case, immediately stop the vehicle in a safe place. Check the engine after it has cooled completely. (→P. 512)
171
2-2. Instrument cluster Indicators and warning lights
The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems.
Instrument cluster
The units used on the speedometer and some indicators may differ depending on the target region. Center panel
172
2-2. Instrument cluster
■ Indicators
The indicators inform the driver of the operating state of the vehicle’s various systems.
(U.S.A.)
(Canada)
Turn signal indicator (→P. 166)
Headlight high beam indicator (→P. 180)
Headlight indicator (→P. 178)
Tail light indicator (→P. 178)
Security indicator (→P. 96, 99)
Shift position and shift range indicators (→P. 161) “SET” indicator (→P. 194)
*1, 2
*1
(U.S.A.)
(Canada) *1
Cruise control indicator (→P. 194)
Slip indicator (→P. 207)
VSC OFF indicator (→P. 207)
TRAC OFF indicator (→P. 208)
TRC OFF indicator (→P. 208)
SRS airbag on-off indicator (→P. 119)
*1: These lights turn on when the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with smart key system) or the engine switch is turned to the “ON” position (vehicles without smart key system) to indicate that a system check is being per- formed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if the lights do not come on, or turn off. Have the vehicle inspected by your Toyota dealer.
*2: The light flashes to indicate that the system is operating.
173
2-2. Instrument cluster
■ Warning lights
Warning lights inform the driver of malfunctions in the indicated vehicle’s systems. (→P. 479)
*1
*1
*1
*1
*1
(U.S.A.) *1
(Canada) *1
(U.S.A.) *1
(Canada) *1, 2
(if equipped) *1
(Canada)
(U.S.A.) *1
(U.S.A.)
*1
*1
*1
*1
(if equipped)
*1: These lights turn on when the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with smart key system) or the engine switch is turned to the “ON” position (vehicles without smart key system) to indicate that a system check is being per- formed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if the lights do not come on, or turn off. Have the vehicle inspected by your Toyota dealer.
*2: The light flashes to indicate that the system is operating.
CAUTION
■If a safety system warning light does not come on
Should a safety system light such as ABS and the SRS airbag warning light not come on when you start the engine, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.
174
2-2. Instrument cluster Multi-information display
The multi-information display presents the driver with a variety of driving-related data including the current outside air temperature.
● Outside
temperature dis-
play
● Trip information
Displays driving range, fuel consumption and other cruis- ing related information
Switching the display
Items displayed can be switched by pressing the “DISP” button.
175
2-2. Instrument cluster
Display items
■ Outside temperature
Displays the outside air temperature
The temperature range that can be displayed is from -40 °F (-40 °C) up to 122 °F (50 °C).
■ Driving range
Displays the estimated maximum distance that can be driven with the quantity of fuel remaining • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed.
• When only a small amount of fuel is added to the
tank, the display may not be updated.
■ Average fuel consumption
Displays the average fuel consumption since the function was reset
The function can be reset by pressing the “DISP” but- ton for longer than 1 second when the average fuel consumption is displayed.
■ Current fuel consumption
Displays the current rate of fuel consumption
176
2
2-2. Instrument cluster
■ Average vehicle speed
Displays the average vehicle speed since the engine was started or the function was reset
The function can be reset by pressing the “DISP” but- ton for longer than 1 second when the average vehi- cle speed is displayed.
■Outside temperature display
In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change. ●When stopped, or driving at low speeds (less than 12 mph [20 km/h]) ●When the outside temperature has changed suddenly (at the entrance/
exit of a garage, tunnel, etc.)
■When disconnecting and reconnecting battery terminals
The following information data will be reset: ●Average fuel consumption ●Driving range ●Average vehicle speed
NOTICE
■The multi-information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed.
177
2-3. Operating the lights and windshield wipers Headlight switch
The headlights can be operated manually or automatically.
Type A
(When
The headlights, parking lights, day- time running lights and so on turn on and off automati- cally. the “ENGINE START STOP” switch is in IGNITION ON mode [vehicles with smart key system] or the engine switch is in the “ON” position [vehicles without smart key system].) The side marker, parking, tail, license plate daytime run- ning lights and instru- ment panel lights turn on. The headlights and all lights listed above (except daytime run- ning lights) turn on. The daytime run- ning lights turn off.
178
2
2-3. Operating the lights and windshield wipers
Type B
run-
The daytime ning lights turn on. The side marker, parking, tail, license plate daytime run- ning lights and instru- ment panel lights turn on. The headlights and all lights listed above (except daytime run- ning lights) turn on. The headlights, parking lights, day- time running lights and so on turn on and off automati- the cally. “ENGINE START STOP” switch is in IGNITION ON mode [vehicles with smart key system] or the engine switch is in “ON” position the [vehicles without smart key system].)
(When
179
2-3. Operating the lights and windshield wipers
Turning on the high beam headlights
With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams. Release to turn them off. You can flash the high beams with the headlights on or off.
■Daytime running light system
●To make your vehicle more visible to other drivers, the headlights turn on automatically (at a reduced intensity) whenever the engine is started and the parking brake is released. Daytime running lights are not designed for use at night.
●Compared to turning on the headlights, the daytime running light system offers greater durability and consumes less electricity, so it can help improve fuel economy.
■Headlight control sensor
The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. Doing so the sensor detecting the level of ambient light and may cause the automatic headlight con- trol system to malfunction.
interferes with
180
2
2-3. Operating the lights and windshield wipers
■Automatic light off system
Vehicles with smart key system
The headlights and tail lights turn off 30 seconds after a door is opened or closed if the “ENGINE START STOP” switch has been turned to ACCES- SORY or turned OFF while the headlights are turned on. (The lights turn off immediately if the button on the key is pressed after all doors are locked.) To turn the lights on again, turn the “ENGINE START STOP” switch to IGNI- TION ON mode, or turn the light switch OFF once and then back to the
or
position.
Vehicles without smart key system
The headlights and tail lights turn off 30 seconds after a door is opened or closed if the engine switch has been turned to the “ACC” or “LOCK” position while the headlights are turned on. (The lights turn off immediately if the button on the key is pressed after all doors are locked.) To turn the lights on again, turn the engine switch to the “ON” position, or turn the light switch OFF once and then back to the position.
or
■Automatic headlight leveling system
The level of the headlights is automatically adjusted according to the number of passengers and the loading condition of the vehicle to ensure that the headlights do not interfere with other road users.
■Customization that can be configured at Toyota dealer
Settings (e.g. light sensor sensitivity) can be changed. (Customizable features →P. 545)
NOTICE
■To prevent battery discharge
Do not leave the lights on longer than necessary if the engine is not running.
181
2-3. Operating the lights and windshield wipers Fog light switch
The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam.
Type A
OFF ON
182
2-3. Operating the lights and windshield wipers
Type B
OFF ON
183
2-3. Operating the lights and windshield wipers Windshield wipers and washer (Type A)
■ Intermittent wiper with interval adjuster (if equipped)
Wiper intervals can be adjusted for intermittent operation (when
is selected).
wiper
Intermittent operation Low speed wiper operation High speed wiper operation Temporary operation
the
Increases intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency
184
2-3. Operating the lights and windshield wipers
Wash/wipe operation Wipers will automatically oper- ate a couple of times after the washer squirts.
■ Raindrop detection windshield wipers (if equipped)
With “AUTO” selected, the wipers will operate automatically when the sensor detects falling rain. The system automatically adjusts wiper timing in accordance with rain volume and vehicle speed.
Raindrop detection wiper operation Low speed wiper operation High speed wiper operation Temporary operation
185
2-3. Operating the lights and windshield wipers
Sensor sensitivity (high) Sensor sensitivity (low)
Wash/wipe operation Wipers will automatically oper- ate a couple of times after the washer squirts.
■The windshield wiper and washer can be operated when
Vehicles with smart key system
The “ENGINE START STOP” switch is in IGNITION ON mode.
Vehicles without smart key system
The engine switch is in the “ON” position.
186
2-3. Operating the lights and windshield wipers
■Effects of vehicle speed on wiper operation
Vehicle speed affects the following even when the wipers are not in “AUTO” mode. ●Intermittent wiper interval ( ●Wiper operation when the washer is being used With low speed mode, wiper operation will be switched from low speed to intermittent wiper operation only when the vehicle is stationary.
mode)
■Rain drop sensor (vehicles equipped with the raindrop detection wind-
shield wipers)
●The sensor judges the amount of rain-
drops. An optical sensor is adopted. It may not operate properly when sunlight from the rising or setting of the sun intermittently strikes the windshield, or if bugs etc. are present on the windshield.
●If the wiper switch is turned to the “AUTO” position while the “ENGINE START STOP” switch is in ON mode, the wipers will operate once to show that “AUTO” mode is activated.
●If the temperature of the raindrop sensor is 194 °F (90 °C) or higher, or 14 °F (-10 °C) or lower, automatic operation may not occur. In this case, operate the wipers in any mode other than “AUTO”.
■If no windshield washer fluid sprays
Check that the washer nozzles are not blocked if there is washer fluid in the windshield washer fluid reservoir.
■Customization that can be configured at Toyota dealer
Settings (e.g. switching operation when the vehicle is stationary) can be changed. (Customizable features →P. 545)
187
2-3. Operating the lights and windshield wipers
CAUTION
■Caution regarding the use of windshield wipers in “AUTO” mode
The windshield wipers may operate unexpectedly if the sensor is touched or the windshield is subject to vibration in “AUTO” mode. Take care that your fingers or anything else do not become caught in the windshield wipers.
NOTICE
■When the windshield is dry
Do not use the wipers, as they may damage the windshield.
■When there is no washer fluid spray from the nozzle
Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.
■When a nozzle becomes blocked
In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged.
188
2
2-3. Operating the lights and windshield wipers Windshield wipers and washer (Type B)
■ Intermittent wiper with interval adjuster (if equipped)
Wiper intervals can be adjusted for intermittent operation (when
is selected).
wiper
Intermittent operation Low speed wiper operation High speed wiper operation Temporary operation
the
Increases intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency
189
2-3. Operating the lights and windshield wipers
Wash/wipe operation Wipers will automatically oper- ate a couple of times after the washer squirts.
■ Raindrop detection windshield wipers (if equipped)
With “AUTO” selected, the wipers will operate automatically when the sensor detects falling rain. The system automatically adjusts wiper timing in accordance with rain volume and vehicle speed.
Raindrop detection wiper operation Low speed wiper operation High speed wiper operation Temporary operation
190
2-3. Operating the lights and windshield wipers
Sensor sensitivity (high) Sensor sensitivity (low)
Wash/wipe operation Wipers will automatically oper- ate a couple of times after the washer squirts.
■The windshield wiper and washer can be operated when
Vehicles with smart key system
The “ENGINE START STOP” switch is in IGNITION ON mode.
Vehicles without smart key system
The engine switch is in the “ON” position.
191
2-3. Operating the lights and windshield wipers
■Effects of vehicle speed on wiper operation
Vehicle speed affects the following even when the wipers are not in “AUTO” mode. ●Intermittent wiper interval ( ●Wiper operation when the washer is being used With low speed mode, wiper operation will be switched from low speed to intermittent wiper operation only when the vehicle is stationary.
mode)
■Rain drop sensor (vehicles equipped with the raindrop detection wind-
shield wipers)
●The sensor judges the amount of rain-
drops. An optical sensor is adopted. It may not operate properly when sunlight from the rising or setting of the sun intermittently strikes the windshield, or if bugs etc. are present on the windshield.
●If the wiper switch is turned to the “AUTO” position while the “ENGINE START STOP” switch is in ON mode, the wipers will operate once to show that “AUTO” mode is activated.
●If the temperature of the raindrop sensor is 194 °F (90 °C) or higher, or 14 °F (-10 °C) or lower, automatic operation may not occur. In this case, operate the wipers in any mode other than “AUTO”.
■If no windshield washer fluid sprays
Check that the washer nozzles are not blocked if there is washer fluid in the windshield washer fluid reservoir.
■Customization that can be configured at Toyota dealer
Settings (e.g. switching operation when the vehicle is stationary) can be changed. (Customizable features →P. 545)
192
2-3. Operating the lights and windshield wipers
CAUTION
■Caution regarding the use of windshield wipers in “AUTO” mode
The windshield wipers may operate unexpectedly if the sensor is touched or the windshield is subject to vibration in “AUTO” mode. Take care that your fingers or anything else do not become caught in the windshield wipers.
NOTICE
■When the windshield is dry
Do not use the wipers, as they may damage the windshield.
■When there is no washer fluid spray from the nozzle
Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.
■When a nozzle becomes blocked
In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged.
193
2-4. Using other driving systems Cruise control
Use the cruise control to maintain a set speed without using the accelerator.
Indicator Cruise control switch
Press the “ON-OFF” button to activate the cruise control.
Press the button once more to deactivate the cruise control.
Accelerate or decelerate the vehicle to the desired speed, and push the lever down to set the speed.
“SET” indicator will come on.
■ Set the vehicle speed STEP 1
STEP 2
194
2
2-4. Using other driving systems
■ Adjusting the speed setting To change the set speed, operate the lever until the desired set speed is obtained.
Increase speed Decrease speed Fine adjustment. Momentarily move the lever in the desired direction. Large adjustment. Hold lever in the desired direction.
the
The set speed will be increased or decreased as follows: Fine adjustment: By approximately 1 mph (1.6 km/h) each time the lever is operated. Large adjustment: The set speed can be increased or decreased continually until the lever is released.
195
2-4. Using other driving systems
■ Canceling and resuming regular acceleration
Pulling the lever toward you cancels the constant speed control. The speed setting is also can- celed when the brakes are applied. Pushing resumes speed control. Resuming is available when the vehicle speed is more than approximately 25 mph (40
km/h).lever up constant
the the
■Cruise control can be set when
●The shift lever is in the “D” or range “4” or higher of “S” has been
selected.
●Vehicle speed is above approximately 25 mph (40 km/h).
■Accelerating
●The vehicle can be accelerated normally. After acceleration, the set
speed resumes.
●Even without canceling the cruise control, the set speed can be increased by first accelerating the vehicle to the desired speed and then pushing the lever down to set the new speed.
196
2
2-4. Using other driving systems
■Automatic cruise control cancelation
The set speed is automatically canceled in any of the following situations. ●Actual vehicle speed falls more than 10 mph (16 km/h) below the preset
vehicle speed. At this time, the memorized set speed is not retained.
●Actual vehicle speed is below approximately 25 mph (40 km/h). ●VSC is activated.
■If the cruise control indicator light flashes
Press the “ON-OFF” button once to deactivate the system, and than press the button again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.
CAUTION
■To avoid operating the cruise control by mistake
Switch the cruise control off using the “ON-OFF” button when not in use.
■Situations unsuitable for cruise control
Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury. ●In heavy traffic ●On roads with sharp bends ●On winding roads ●On slippery roads, such as those covered with rain, ice or snow ●On steep hills
Vehicle speed may exceed the set speed when driving down a steep hill.
197
2-4. Using other driving systems Rear view monitor system∗
The rear view monitor system assists the driver by displaying an image of the view behind the vehicle while reversing. The image is displayed in reverse on the screen. This allows the image to appear in the same manner as that of the rear view mirror.
With navigation system
Refer to the “Navigation System Owner’s Manual”.
Without navigation system
Vehicles with smart key sys- tem: To display the rear view image on the inside rear view mirror, the shift lever is in the “R” position when the “ENGINE START STOP” switch is in the IGNITION ON mode. Vehicles without smart key system: To display the rear view image on the inside rear view mirror, the shift lever is in the “R” position when the engine switch is in the “ON” position. This reversed image is a simi- lar image to the one on the inside rear view mirror. If you move the lever out of “R”, the screen is turned off.
198
∗: If equipped
■Switching the screen
2-4. Using other driving systems
On Green indicator comes on. Off Orange indicator comes on.
■When using the rear view monitor system
The anti-glare function of the inside rear view mirror will be canceled.
■Automatic shut off
The display will be turned off automatically after 5 minutes.
■Display mode
The rear view monitor display mode can be adjusted when the engine switch is in the ON and the shift lever is in R.
Push the
button.
199
2-4. Using other driving systems
●To temporarily turn off the monitor when it is on.
button. The indicator should turn orange.
Push the The monitor will automatically turn on again after the engine switch is turned OFF and ON.
●To manually turn on the monitor when it is turned off.
Push the
button. The indicator should turn green.
●To select a display language (English, French or Spanish). STEP 1
button for 6 to 12 seconds.button.
Push and hold the The monitor should turn on and the indicator should turn green. Push the Each time the will change. The warning message should flash 5 seconds after the button is released, indicating that the change has been completed.
button is pushed and released, the language
STEP 2
STEP 3
●To permanently disable the monitor.
button for 12 to 15 seconds.
Push and hold the The monitor will turn off and on after 6 seconds. Continue holding the button down until the display turns back off. The indicator should flash orange. The monitor will not automatically turn on again after the engine switch is turned OFF and ON.
200
■Displayed area
2-4. Using other driving systems
the bumper or under
The area covered by the camera is lim- ited. Objects which are close to either corner of the bumper cannot be seen on the screen. The area displayed on the screen may vary according to vehicle orientation or road conditions.
Corners of bumper
■Driving precautions
the grade behind
When the vehicle slopes up sharply, objects appear to be farther away than they actually are.
201
2-4. Using other driving systems
the grade behind
When the vehicle slopes down sharply, objects appear to be closer than they actually are.
The distance that appears on the screen between three-dimensional objects (such as vehicles) and flat surfaces (such as the road) and the actual distance differ as follows. In reality, C = A < B (C and A are equally far away; B is farther than C and A). How- ever, on the screen, the situation appears to be A < B < C. On the screen, it appears that a truck is parking about 0.5 m (1.5 ft.) away. How- ever, in reality if you back up to point A, you will hit the truck.
202
2-4. Using other driving systems
■Rear view monitor guide lines
Guide lines are displayed on the screen.
Guide lines shown differ from those shown on the actual screen. Vehicle width extension guide lines (blue) These lines indicate the estimated vehicle width extension. Distance guide line (blue) This line indicates a position on the ground about 3 ft. (1 m) behind on the ground of the rear bumper of your vehicle. Distance guide line (red) This line indicates a position on the ground about 1.5 ft. (0.5 m) behind on the ground of the rear bumper of your vehicle. Vehicle center guide lines (blue) These lines indicate the estimated vehicle center on the ground.
203
2-4. Using other driving systems
■Rear view monitor system camera
In the following cases, it may be difficult to see the images on the screen, even when the system is functioning correctly. • In the dark (e.g. at night). • If the temperature near the lens is
extremely high or low.
• If water droplets get on the camera, or when humidity is high (e.g. when it rains).
• If foreign matter (e.g. snow or mud)
get on the camera lens.
• If the sun or headlights are shining
directly into the camera lens.
• When the camera has scratches or
