Login- Download PDF Manual
-
SAE 5W-30 is the best choice for good fuel economy and good starting in cold weather. If SAE 5W-30 is not available, SAE 10W-30 oil may be used. However, it should be replaced with SAE 5W-30 at the next oil change.
Outside temperature
The 5W portion of the oil viscosity rating indicates the characteristic of the oil which allows cold startability. Oils with a lower value before the W allow for easier starting of the engine in cold weather. The 30 in 5W-30 indicates the oil viscosity when the oil is at its operating temperature. An oil with a higher viscosity may be better suited if the vehi- cle is operated at high speeds, or under extreme load conditions.
How to read oil container label: The ILSAC (International Lubricant Standardization and Approval Committee) Certification Mark is added to some oil containers to help you select the oil you should use.
523
6-1. Specifications
Cooling system
Capacity
Coolant type
8.8 qt. (8.3 L, 7.3 lmp.qt.) Use either of the following: • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based non- silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technol- ogy Do not use plain water alone.
Ignition system
Spark plug Make Gap
DENSO
FK20HR11
0.043 in. (1.1 mm)NOTICE
■Iridium-tipped spark plugs
Use only iridium-tipped spark plugs. Do not adjust gap when tuning engine.
Electrical system
Battery Open voltage at 68 °F (20 °C):
12.6 ⎯ 12.8 V Fully charged 12.2 ⎯ 12.4 V Half charged 11.8 ⎯ 12.0 V Discharged (Voltage is checked 20 minutes after the engine and all lights are turned off.)
Charging rates
5A max.
524
6-1. Specifications
Automatic transaxle
Fluid capacity* Fluid type *: The fluid capacity is the quantity of reference. If replacement is necessary,
6.9 qt. (6.5 L, 5.7 lmp.qt.) Toyota Genuine ATF WS
contact your Toyota dealer.
NOTICE
■Automatic transmission fluid type
Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the automatic transmis- sion of your vehicle.
Brakes
2.4 in. (61 mm) Min. Less than 0.04 ⎯ 0.24 in. (1.0 ⎯ 6.0 mm) 0.04 in. (1.0 mm)
Pedal clearance*1
Pedal free play Brake pad wear limit Parking brake pedal travel*2
Parking brake lining wear limit Fluid type *1: Minimum pedal clearance when depressed with a force of 110 lbf (490 N, 50SAE J1703 or FMVSS No. 116 DOT 3
0.04 in. (1.0 mm)
9 ⎯ 11 clicks
kgf) while the engine is running.
*2: Parking brake pedal travel when depressed with a force of 66 lbf (294 N, 30
kgf).
525
6-1. Specifications
Steering
Free play
Tires and wheels
Type A
Tire size
Front and rear tire inflation pressure (Recommended cold tire inflation pressure)
Wheel size Wheel nut torque
Type B
Tire size
Front and rear tire inflation pressure (Recommended cold tire inflation pressure)
Wheel size Wheel nut torque
526
Less than 1.2 in. (30 mm)
P215/55R17 93V
Vehicle speed
psi (kPa, kgf/cm2 or bar)
38 (260, 2.6)
32 (220, 2.2)
More than 99 mph (160 km/h) 99 mph (160 km/h) or less 17 × 7J 76 ft•lbf (103 N•m, 10.5 kgf•m)
P215/60R16 94V
Vehicle speed
psi (kPa, kgf/cm2 or bar)
35 (240, 2.4)
29 (200, 2.0)
More than 99 mph (160 km/h) 99 mph (160 km/h) or less 16 × 6 1/2JJ 76 ft•lbf (103 N•m, 10.5 kgf•m)
6-1. Specifications
Light bulbs
Light Bulbs
Bulb No.
35
55
60
55D4S H11
HB3
H11
W5W3457NA
28/8
W5W 7440A 7440
W5W 921
W5W W5W W5W 7065
74
168
282521
21
16
1.4
1.2
4.8Exterior
Headlights Low beam (discharge bulbs) Low beam (halogen bulbs) High beam Fog lights Auxiliary light Front turn signal/parking lights Front side marker lights Rear turn signal lights Stop lights Rear side marker lights Back-up lights License plate lights Interior light Personal lights Vanity lights Glove box light Door courtesy lights Trunk light A: D4S discharge bulbs B: H11 halogen bulbs C: HB3 halogen bulbs D: Wedge base bulbs (amber) E: Wedge base bulbs (clear) F: Double end bulbs
Interior
Type
527
6-1. Specifications Fuel information
Your vehicle must use only unleaded gasoline. Select octane rating 87 (Research Octane Number 91) or higher. Use of unleaded gasoline with an octane rating lower than 87 may result in engine knocking. Persistent knocking can lead to engine damage. At minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada.
■Fuel tank opening for unleaded gasoline
To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps.
■If your engine knocks
●Consult your Toyota dealer. ●You may occasionally notice light knocking for a short time while acceler-
ating or driving uphill. This is normal and there is no need for concern.
■Gasoline quality
In very few cases, driveability problems may be caused by the brand of gas- oline you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer.
528
6-1. Specifications
■Gasoline quality standards
●Automotive manufacturers in the US, Europe and Japan have developed a specification for fuel quality called World-Wide Fuel Charter (WWFC) that is expected to be applied worldwide.
●The WWFC consists of four categories that are based on required emis-
sion levels. In the US, category 4 has been adopted.
●The WWFC improves air quality by lowering emissions in vehicle fleets,
and customer satisfaction through better performance.
■Toyota recommends the use of gasoline containing detergent additives ●Toyota recommends the use of gasoline that contains detergent additives
to avoid build-up of engine deposits.
●All gasoline sold in the US contains detergent additives to clean and/or
keep clean intake systems.
■Toyota recommends the use of cleaner burning gasoline
Cleaner burning gasoline, including reformulated gasoline that contains oxy- genates such as ethanol or MTBE (Methyl Tertiary Butyl Ether) is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gasoline provide excellent vehicle performance, reduce vehicle emissions and improve air quality.
529
6-1. Specifications
■Toyota does not recommend blended gasoline
Do not use gasoline containing more than 10% ethanol.
(15% ethanol)
(50% ethanol)
(85% ethanol)
●Use only gasoline containing a maxi-
mum of 10% ethanol. DO NOT use any flex-fuel or gasoline that could contain more than 10% etha- nol, including from any pump labeled E15, E30, E50 E85 (which are only some examples of fuel containing more than 10% ethanol).
●If you use gasohol in your Toyota, be sure that it has an octane rating no
lower than 87.
●Toyota DOES NOT recommend the use of gasoline containing methanol.
■Toyota does not recommend gasoline containing MMT
Some gasoline contains octane enhancing additive called MMT (Methylcy clopentadienyl Manganese Tricarbonyl). Toyota DOES NOT recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected. The malfunction indicator lamp on the instrument cluster may come on. If this happens, contact your Toyota dealer for service.
530
6-1. Specifications
NOTICE
■Notice on fuel quality
●Do not use improper fuels. If improper fuels are used the engine will be
damaged.
●Do not use leaded gasoline.
Leaded gasoline can cause damage to your vehicle’s three-way catalytic converters causing the emission control system to malfunction.
●Do not use gasohol other than that stated here.
Other gasohol may cause fuel system damage or vehicle performance problems.
●Using unleaded gasoline with an octane number or rating lower than that
stated here will cause persistent heavy knocking. At worst, this will lead to engine damage.
■Fuel-related poor driveability
If after using a different type of fuel, poor driveability is encountered (poor hot starting, vaporization, engine knocking, etc.), discontinue the use of that type of fuel.
■When refueling with gasohole
Take care not to spill gasohol. It can damage your vehicle’s paint.
531
6-1. Specifications Tire information
Typical tire symbols
(→P. 534) (→P. 533) (→P. 421)
Tire size DOT and Tire Identification Number (TIN) Location of treadwear indicators Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire. Radial tires or bias-ply tires A radial tire has RADIAL on the sidewall. A tire not marked RADIAL is a bias-ply tire. TUBELESS or TUBE TYPE A tubeless tire does not have a tube and air is directly filled in the tire. A tube type tire has a tube inside the tire and the tube main- tains the air pressure.
532
6-1. Specifications
Maximum cold tire inflation pressure This means the pressure to which a tire may be inflated. (→P. 538) Load limit at maximum cold tire inflation pressure Summer tire or all season tire (→P. 426) An all season tire has “M+S” on the sidewall. A tire not marked “M+S” is a summer tire.
(→P. 538)
Typical DOT and tire identification number (TIN)
Identification Number
DOT symbol* Tire (TIN) Tire manufacturer’s identifica- tion mark Tire size code Manufacturer’s optional type code (3 or 4 letters) Manufacturing week Manufacturing year *: The DOT symbol certifies that to applicable Federal Motor Vehicle Safety Standards.
tire conforms
the
tire
533
The illustration indicates typical tire size.
Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 or 3 digits) Speed symbol (alphabet with one letter)
Section width Tire height Wheel diameter
6-1. Specifications
Tire size
■ Typical tire size information
■ Tire dimensions
534
6-1. Specifications
Tire section names
Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer
Uniform Tire Quality Grading
This information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading.
Your Toyota dealer will help answer any questions you may have as you read this information.
535
6-1. Specifications
■ DOT quality grades
All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A
■ Treadwear
The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speci- fied government test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.
■ Traction AA, A, B, C
The traction grades, from highest to lowest, are AA, A, B and C, and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on braking (straight ahead) traction tests and does not include cornering (turn- ing) traction.
536
6-1. Specifications
■ Temperature A, B, C
The temperature grades are A (the highest), B, and C, represent- ing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speci- fied indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passen- ger car tires must meet under the Federal Motor Vehicle Safety Stan- dard No. 109. Grades B and A represent higher levels of performance on the labo- ratory test wheel than the minimum required by law. Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either sepa- rately or in combination, can cause heat buildup and possible tire fail- ure.
537
6-1. Specifications
Glossary of tire terminology
Tire related term
Meaning
Tire pressure when the vehicle has been parked for three hours or more, or has not been driven more than 1 mile or 1.5 km under that condition The maximum cold inflated pressure to which a tire may be inflated, shown on the sidewall of the tire Cold tire inflation pressure recommended by a manufacturer. The combined weight (in excess of those stan- dard items which may be replaced) of trans- mission, power steering, power brakes, power windows, power seats, radio and heater, to the extent that these items are available as factory- installed equipment (whether installed or not) The weight of a motor vehicle with standard equipment, including the maximum capacity of fuel, oil and coolant, and if so equipped, air conditioning and additional weight optional engine The sum of: (a) Curb weight (b) Accessory weight (c) Vehicle capacity weight (d) Production options weight 150 lb. (68 kg) times the number of occupants specified in the second column of Table 1* that follows
Cold tire inflation pressure
Maximum inflation pressure
Recommended inflation pressure
Accessory weight
Curb weight
Maximum loaded vehicle weight
Normal occupant weight
538
6-1. Specifications
Tire related term
Occupant distribution
Production options weight
Rim
Rim diameter (Wheel diameter) Rim size designation
Rim type designation
Rim width Vehicle capacity weight (Total load capacity)
Vehicle maximum load on the tire
Vehicle normal load on the tire
Meaning
Distribution of occupants in a vehicle as speci- fied in the third column of Table 1* below The combined weight of installed regular pro- duction options weighing over 5 lb. (2.3 kg) in excess of the standard items which they replace, not previously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim A metal support for a tire or a tire and tube assembly upon which the tire beads are seated
Nominal diameter of the bead seat
Rim diameter and width The industry manufacturer’s designation for a rim by style or code Nominal distance between rim flanges The rated cargo and luggage load plus 150 lb. (68 kg) times the vehicle’s designated seating capacity The load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight, and dividing by two The load on an individual tire that is determined by distributing to each axle its share of curb weight, accessory weight, and normal occu- pant weight (distributed in accordance with Table 1* below), and dividing it by two
539
6-1. Specifications
Tire related term
Weather side
Bead
Bead separation
Bias ply tire
Carcass
Chunking
Cord
Cord separation
Cracking
CT
Extra load tire
540
Meaning
The surface area of the rim not covered by the inflated tire The part of the tire that is made of steel wires, wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components in the bead A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles substantially less than 90 degrees to the cen- terline of the tread The tire structure, except tread and sidewall rubber which, when inflated, bears the load The breaking away of pieces of the tread or sidewall The strands forming the plies in the tire The parting of cords from adjacent rubber com- pounds Any parting within the tread, sidewall, or inner- liner of the tire extending to cord material A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire A tire designed to operate at higher loads and at higher inflation pressures than the corre- sponding standard tire
6-1. Specifications
Tire related term
Meaning
Groove
Innerliner
Innerliner separation
Intended outboard sidewall
Light truck (LT) tire
Load rating
Maximum load rating
Maximum permissible inflation pressure
Measuring rim
Open splice
Outer diameter
The space between two adjacent tread ribs The layer(s) forming the inside surface of a tubeless tire that contains the inflating medium within the tire The parting of the innerliner from cord material in the carcass (a)The sidewall that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (b)The outward facing sidewall of asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle A tire designated by its manufacturer as prima- rily intended for use on lightweight trucks or multipurpose passenger vehicles The maximum load that a tire is rated to carry for a given inflation pressure The load rating for a tire at the maximum per- missible inflation pressure for that tire The maximum cold inflation pressure to which a tire may be inflated The rim on which a tire is fitted for physical dimension requirements Any parting at any junction of tread, sidewall, or innerliner that extends to cord material The overall diameter of an inflated new tire
541
6-1. Specifications
Tire related term
Meaning
Overall width
Passenger car tire
Ply
Ply separation
Pneumatic tire
Radial ply tire
Reinforced tire
Section width
The linear distance between the exteriors of the sidewalls of an inflated tire, including eleva- tions due to labeling, decorations, or protective bands or ribs A tire intended for use on passenger cars, mul- tipurpose passenger vehicles, and trucks, that have a gross vehicle weight rating (GVWR) of 10,000 lb. or less A layer of rubber-coated parallel cords A parting of rubber compound between adja- cent plies A mechanical device made of rubber, chemi- cals, fabric and steel or other materials, that, when mounted on an automotive wheel, pro- vides the traction and contains the gas or fluid that sustains the load A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90 degrees to the centerline of the tread A tire designed to operate at higher loads and at higher inflation pressures than the corre- sponding standard tire The linear distance between the exteriors of the sidewalls of an inflated tire, excluding ele- vations due to labeling, decoration, or protec- tive bands
542
6-1. Specifications
Tire related term
Meaning
Sidewall
Sidewall separation
Snow tire
Test rim
Tread
Tread rib
Tread separation
Treadwear indicators (TWI)
Wheel-holding fixture
) on at
That portion of a tire between the tread and bead The parting of the rubber compound from the cord material in the sidewall A tire that attains a traction index equal to or greater than 110, compared to the ASTM E- 1136 Standard Reference Test Tire, when using the snow traction test as described in ASTM F-1805-00, Standard Test Method for Single Wheel Driving Traction in a Straight Line on Snow-and Ice-Covered Surfaces, and which is marked with an Alpine Symbol ( least one sidewall The rim on which a tire is fitted for testing, and may be any rim listed as appropriate for use with that tire That portion of a tire that comes into contact with the road A tread section running circumferentially around a tire Pulling away of the tread from the tire carcass The projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread The fixture used to hold the wheel and tire assembly securely during testing
*: Table 1 ⎯ Occupant loading and distri bution for vehicle normal load
for various designated seating capacities
543
Vehicle normal load, Number of occupants
Occupant distribution in
a normally loaded
vehicle
2 in front 2 in front, 1 in second seat 2 in front, 1 in second seat, 1 in third seat, 1 in fourth seat 2 in front, 2 in second seat, 2 in third seat, 1 in fourth seat
6-1. Specifications
Designated seating capacity, Number of
occupants 2 through 4
5 through 10
11 through 15
16 through 20
544
6-2. Customization Customizable features
Your vehicle includes a variety of electronic features that can be per- sonalized to your preferences. Programming these preferences requires specialized equipment and may be performed by your Toyota dealer. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer for further details.
Item
Function
Default setting
Smart key system (→P. 30)
Wireless remote control (→P. 42)
Smart key system Operation signal (Emergency flashers) Operation signal (Buzzer)
Unlocking operation
Time elapsed before automatic door lock function is activated if door is not opened after being unlocked
ON
ON
ON
Driver’s door unlocked in 1- step, all doors unlocked in 2-step
Customized
setting OFF
OFF
OFF
All doors unlocked in 1-step
OFF
60 seconds
30 seconds
120 seconds
545
6-2. Customization
Item
Function
Default setting
Customized
setting
OFF
OFF
OFF
ON
ON
ON
Push and hold
Push twice
One short push
ON
ON
OFF
OFF
Wireless remote control (→P. 42)
Operation indicator (Emergency flashers) Operation indicator (Buzzer) Trunk unlocking func- tion
Trunk unlocking opera- tion
Panic function Buzzer sounds when pushing with any door not closed
546
Item
Function
Default setting
Unlocking using a key
Speed-detecting auto- matic door lock function Opening driver’s door unlocks all doors Shift the shift lever to “P” unlocks all doors Shift the shift lever to position other than “P” locks all doors Light sensor sensitivity Time elapsed before headlights automati- cally turn off after doors are closed Daytime running light
Door lock (→P. 47)
Automatic light control system (→P. 178)
*: Vehicles sold outside Canada
6-2. Customization
Customized
setting
All doors unlocked in 1-step
ON
ON
OFF
OFF
Driver’s door unlocked in 1- step, all doors unlocked in 2-step
OFF
OFF
ON
ON
Level 3
60 seconds
ON
Levels 1 to 5
0 seconds 30 seconds 90 secondsOFF*
547
6-2. Customization
Item
Function
Default setting
Customized
setting
Windshield wipers and washer (→P. 189)
Illumination (→P. 346)
Switching operation when the vehicle is sta- tionary
Time elapsed before the drip prevention function operates
Time elapsed before lights turn off
Operation when the doors are unlocked Operation after the “ENGINE START STOP” switch or the engine switch turned OFF Front/rear personal lights turned on when a door is opened Outer foot lights
Rear sunshade (→P. 366)
Time elapsed before the reverse operation feature activates
ON
OFF
Variable depending on the vehicle speed
15 seconds
ON
ON
Corresponding
light only
ON
0.7 seconds
3 seconds
7.5 seconds 30 seconds
OFF
OFF
All lights
OFF
OFF
0 seconds 0.9 seconds 1.2 seconds
548
6-3. Initialization Items to initialize
After reconnecting or performing maintenance on the battery, the fol- lowing items must be initialized for normal system operation.
Item
Power window
Moon roof
Maintenance data
Tire pressure warning system
When to initialize
Reference
• After reconnecting or changing the battery • After changing a fuse
After the maintenance is performed • When rotating the tire on vehicles with differing front and rear tire infla- tion pressures • When changing tire pressure (such as when changing traveling speed) • When changing tire size
P. 86
P. 90
P. 410
P. 423
549
6-3. Initialization
550
Reporting safety defects for U.S. owners
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA can- not become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov ; or write to: Administrator, NHTSA, 1200 New Jersey Ave, S.E., Washington, DC 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
552
Seat belt instructions for Canadian owners (in French)
The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English.
553
554
7
555
SRS airbag instructions for Canadian owners (in French)
556
7
557
558
7
559
560
7
561
562
7
563
564
7
565
566
Abbreviation list Abbreviation/Acronym list
ABBREVIATIONS
MEANING
A/C ABS ACC ALR CRS ECU EDR ELR GAWR
I/M
LATCH LED MMT M + S MTBE OBD SRS TIN TPMS TRAC VIN VSC
Air Conditioning Anti-lock Brake System Accessory Automatic Locking Retractor Child Restraint System Electronic Control Unit Event Data Recorder Emergency Locking Retractor Gross Axle Weight Ratings Emission inspection and maintenance Lower Anchors and Tethers for Children Light Emitting Diode Methylcy clopentadienyl Manganese Tricarbonyl Mud and Snow Methyl Tertiary Butyl Ether On Board Diagnostics Supplemental Restraint System Tire Identification Number Tire Pressure Monitoring (Warning) System Traction Control Vehicle Identification Number Vehicle Stability Control
568
What to do if... What to do if...
A tire punctures
P. 491 If you have a flat tire
The engine does not start
P. 96 Engine immobilizer system P. 501 If the engine will not start P. 508 If the battery is discharged
The shift lever cannot be moved out
P. 503 If the shift lever cannot be shifted
from “P”
The engine coolant temperature gauge enters the red zone
Steam can be seen coming from under the hood
P. 512 If your vehicle overheats
The key is lost
P. 504 If you lose your keys
The battery runs out
P. 508 If the battery is discharged
The doors cannot be locked
P. 47 Doors
The horn begins to sound
P. 99 Alarm
The vehicle is stuck in mud or sand
P. 515 If the vehicle becomes stuck
576
What to do if...
The warning light or indicator light comes on
P. 479 If the warning light turns on
■Warning lights
Brake system warning light
Malfunction indicator lamp
or
or
or
P. 479
P. 480
ABS warning light
P. 481
Low fuel level warning light P. 482
SRS warning light
P. 481
Open door warning light P. 481
Charging system warning light
P. 480
Slip indicator light
P. 481
Driver’s seat belt reminder light P. 482
Front passenger’s seat belt reminder lightP. 482
Tire pressure warning light P. 482
Automatic headlight leveling system warning lightP. 481
Low engine oil pressure warning light P. 480
Maintenance required reminder light P. 483
Low washer fluid warning light
P. 483
577
What to do if...
578
What to do if...
579
GAS STATION INFORMATION
Auxiliary catch lever
Trunk opener
P. 403
P. 54
Fuel filler door
P. 92
Hood lock release
lever P. 403
Fuel filler door opener
Tire inflation pressure
P. 92
P. 526
Fuel tank capacity (Reference) Fuel type Cold tire inflation pressure Engine oil capacity (Drain and refill — reference)
Engine oil type
18.5 gal. (70 L, 15.4 lmp.gal.)
Unleaded gasoline only
P. 92, 522
P. 526With filter Without filter “Toyota Genuine Motor Oil” or equivalent Oil grade: ILSAC multigrade engine oil
qt. (L, Imp.qt.) 6.4 (6.1, 5.4) 6.0 (5.7, 5.0)
P. 522
580
For your information
Main Owner’s Manual
Please note that this manual applies to all models and explains all equip- ment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle. All specifications provided in this manual are current at the time of printing. However, because of the Toyota policy of continual product improvement, we reserve the right to make changes at any time without notice. Depending on specifications, the vehicle shown in the illustration may differ from your vehicle in terms of equipment.
Noise from under vehicle after turning off the engine
Approximately five hours after the engine is turned off, you may hear sound coming from under the vehicle for several minutes. This is the sound of a fuel evaporation leakage check and, it does not indicate a malfunction.
18
Accessories, spare parts and modification of your Toyota
A wide variety of non-genuine spare parts and accessories for Toyota vehi- cles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle. This vehicle should not be modified with non-genuine Toyota products. Mod- ification with non-genuine Toyota products could affect its performance, safety or durability, and may even violate governmental regulations. In addi- tion, damage or performance problems resulting from the modification may not be covered under warranty.
Installation of a mobile two-way radio system
As the installation of a mobile two-way radio system in your vehicle could affect electronic systems such as the multiport fuel injection system/sequen- tial multiport fuel injection system, electronic throttle control system, cruise control system, vehicle stability control system, SRS airbag system and seat belt pretensioner system, be sure to check with your Toyota dealer for pre- cautionary measures or special instructions regarding installation.
19
Scrapping of your Toyota
The SRS airbag and seat belt pretensioner devices in your Toyota contain explosive chemicals. If the vehicle is scrapped with the airbags and seat belt pretensioners left as they are, this may cause an accident such as fire. Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.
Perchlorate Material
Special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate. Your vehicle has components that may contain perchlorate. These compo- nents may include airbag, seat belt pretensioners, and wireless remote con- trol batteries.
20
Vehicle control and operation data recording
Your Toyota is equipped with sophisticated computers that record certain information about your vehicle’s operation, such as: • Engine speed • Accelerator status • Brake status • Vehicle speed • Shift position The data recorded varies according to the grade level and options the vehi- cle is equipped with. The computers do not record conversations, sound or pictures. ● Data usage Toyota may use the data recorded in these computers to diagnose malfunc- tions, conduct research and development, and improve quality. Toyota will not disclose the recorded data to a third party except: • With the consent of the vehicle owner or with the consent of the lessee if
the vehicle is leased In response to an official request by the police, a court of law or a govern- ment agency
• For research purposes where the data is not tied to a specific vehicle or
•
vehicle owner
21
Event data recorder
This vehicle is equipped with an event data recorder (EDR). The main pur- pose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The EDR in this vehicle is designed to record such data as: • How various systems in your vehicle were operating; • Whether or not the driver and passenger safety belts were buckled/fas-
• How far (if at all) the driver was depressing the accelerator and/or brake
tened;
pedal; and,
• How fast the vehicle was traveling. These data can help provide a better understanding of the circumstances in which crashes and injuries occur. NOTE: EDR data are recorded by your vehicle only if a non-trivial crash situ- ation occurs; no data are recorded by the EDR under normal driving condi- tions and no personal data (e.g., name, gender, age, and crash location) are recorded. However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation. To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.
22
● Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except when: • An agreement from the vehicle’s owner (or the lessee for a leased vehicle)
is obtained
• Officially requested by the police or other authorities • For use by Toyota in a lawsuit • Ordered by a court of law However, if necessary, Toyota will: • Use the data for research on vehicle safety performance • Disclose the data to a third party for research purposes without disclosing
information about the specific vehicle or vehicle owner
23
CAUTION
■General precautions while driving
Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that will hurt or kill you, your occupants or others. Defensive driving: Always drive defensively. Anticipate mistakes that other drivers or pedestrians might make and be ready to avoid accidents. Driver distraction: Always give your full attention to driving. Anything that dis- tracts the driver, such as adjusting controls, talking on a cellular phone or reading can result in a collision with resulting death or serious injury to you, your occupants or others.
■General precautions regarding children’s safety
Never leave children unattended in the vehicle, and never allow children to have or use the key. Children may be able to start the vehicle or shift the vehicle into neutral. There is also a danger that children may injure themselves by playing with the cigarette lighter, the windows, the moon roof, or other features of the vehicle. In addition, heat build-up or extremely cold temperatures inside the vehicle can be fatal to children.
24
Symbols used throughout this manual
Cautions & Notices
CAUTION
This is a warning against anything which may cause injury to people if the warning is ignored. You are informed about what you must or must not do in order to reduce the risk of injury to yourself and others.
NOTICE
This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.
25
Symbols used in illustrations
Safety symbol The symbol of a circle with a slash through it means “Do not”, “Do not do this”, or “Do not let this happen”.
Arrows indicating operations
Indicates the action (pushing, turn- ing, etc.) used to operate switches and other devices. Indicates the outcome of an opera- tion (e.g. a lid opens).
26
TABLE OF CONTENTS
1 Before driving
Adjusting and operating features such as door locks, mirrors, and steering column.
2 When driving
Driving, stopping and safe-driving information.
3 Interior features
Air conditioning and audio systems, as well as other interior features for a comfortable driving experience.
4 Maintenance
and care
Cleaning and protecting your vehicle, performing do-it- yourself maintenance, and maintenance information.
5 When trouble
arises
What to do if the vehicle needs to be towed, gets a flat tire, or is involved in an accident.
6 Vehicle
specifications
Detailed vehicle information.
7 For owners
Reporting safety defects for U.S. owners, and seat belt and SRS airbag instructions for Canadian owners.
Index
Alphabetical listing of information contained in this manual.
1-1. Key information Keys
The following keys are provided with the vehicle.
Vehicles with smart key system
Electronic keys • Operating
system (→P. 30)
the smart key
• Operating
the wireless
remote control function (→P. 42)
Mechanical keys Key number plate
Vehicles without smart key system
Master keys Operating the wireless remote control function (→P. 42) Key number plate
