2011 Subaru Tribeca Owners Manual

” button opens the rear

Pressing the “ gate. An electronic chirp will sound twice and the turn signal lights will flash twice.

& Illuminated entry Interior lights such as the map light, dome light and cargo area light will illuminate when the “ ” button is pressed. These lights remain illuminated for approximately 30 seconds if any of the doors or the rear gate is not opened. If seconds have elapsed, turn off. To activate this function, set the following interior light switches to the indicated

the “ ” button is pressed before 30
these lights will

Black plate (112,1)

positions: Map light: OFF position Dome light: DOOR position Cargo area light: DOOR position

A SUBARU dealer can change the illumi- nation period setting of the interior lights in accordance with your preference. Contact the nearest SUBARU dealer for details.

& Vehicle finder function Use this function to find your vehicle parked among many vehicles in a large parking lot. Provided you are within 30 feet (10 meters) of the vehicle, pressing the “ ” button three times in a 5-second period will cause your vehicle’s horn to sound once and its turn signal lights to flash three times. NOTE If the interval between presses is too short when you press the “ ” button three times, the system may not re- spond to the signals from the remote transmitter.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

& Sounding a panic alarm

To activate the alarm, press the “PANIC” button once. The horn will sound and the turn signal lights will flash. To deactivate the panic alarm, press any button on the remote transmitter. Unless a button on the remote transmitter is pressed, the alarm will be deactivated after approximately 30 seconds.

& Selecting audible signal op-

eration

Using an electronic chirp, the system will give you an audible signal when the doors lock and unlock. If desired, you may turn the audible signal off. Do the following to deactivate the audible

in the driver’s seat and shut all

signal. You can also use the same steps to restore the function. 1. Sit doors and the rear gate. 2. Hold down the UNLOCK side of the power door locking switch. 3. While holding down the “UNLOCK” side of the power door locking switch, pull the key out and re-insert it into the ignition switch at least 6 times within 10 seconds after Step 2. 4. Open and close the driver’s door once within 10 seconds after step 3. 5. The turn signal lights flash 3 times to indicate completion of the setting.

You may have the above settings done by your SUBARU dealer. & Replacing the battery

CAUTION

. Do not let dust, oil or water get on or in the transmitter when repla- cing the battery. . Be careful not

to damage the printed circuit board in the trans- mitter when replacing the battery. . Be careful not to allow children to touch the battery and any re- moved parts; children could

Black plate (113,1)

Keys and doors 2-11

swallow them.

. There is a danger of explosion if an incorrect replacement battery is used. Replace only with the same or equivalent type of bat- tery.

. Batteries should not be exposed to excessive heat such as sun- shine, fire or the like.

When the transmitter battery begins to get weak, range will begin to decrease. Replace the battery as soon as possible.

transmitter

To replace the battery:

1. Remove the screw on the key head.

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

2-12 Keys and doors

2. Open the key head using a flat-head screwdriver.

4. Open the transmitter case by releasing the hooks. 5. Remove the old battery from the holder.

3. Remove the transmitter case from the key head.

1) Negative (−) side facing up

Black plate (114,1)

6. Replace with a new battery (Type CR1620 or equivalent) making sure to install the new battery with the negative (−) side facing up. 7. Put together the transmitter case by fitting the hooks on both sides of the case. 8. Put the transmitter case in the key head and then put together the key head. 9. Reinstall the screw on the key head.

After the battery is replaced, the trans- mitter must be synchronized with the remote keyless entry system’s control unit. Press either the “ ” or “ ” button six times to synchronize the unit. & Replacing lost transmitters to If you lose a transmitter or want purchase additional transmitters (up to four can be programmed), you should re- program all of your transmitters for secur- ity reasons. It is recommended that you have your dealer program all of your transmitters into your system. ! Programming the transmitters The remote keyless entry system is equipped with a special code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

different. Programming transmitter codes into system:

Key tag

remote keyless entry system, it is neces- sary to program the transmitter’s code (identification number) into the system. A tag showing the code is affixed to the key unit, and another is affixed to the circuit board inside the transmitter. If there is no tag, open the transmitter case and make a note of the eight-digit number. Program the number into the system in accordance with the following procedure. 1. Firmly close the doors and the rear gate. 2. Open the driver’s door, sit on the driver’s seat, and close the door. 3. Perform the following steps within 45
seconds.

Transmitter circuit board

To register a new transmitter with the

(1) Open and close the driver’s door once.

Black plate (115,1)

Keys and doors 2-13

LOCK

1) 2) ON

(2) Insert the key into the ignition switch, then turn it from the “LOCK” position to the “ON” position 10 times within 15 seconds.

NOTE . When you complete step (2), an electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered. . If you do not perform steps (1) and (2) within 45 seconds, an error will occur. Neither an electronic tone nor the buzzer will sound, and the interior lamp will not flash. In this event, per-

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

2-14 Keys and doors

form the whole procedure again begin- ning with part 1. 4. Open and close the door once within 15 seconds. NOTE . When part 4 of the procedure is completed, an electronic tone will sound for 30 seconds. . If you do not perform the operations in part 4 within 15 seconds, an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with part 3 of the procedure.

ter code. For example, push the locking switch eight times if the leftmost digit of the code is 8. NOTE . The electronic tone will stop sound- ing when you start entering the num- ber. . If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 of the procedure. . If the interval between one push of the knob and the next exceeds 5
seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.

5. Before the electronic tone stops sounding, push the “ ” side of the power door locking switch the same number of times as the leftmost digit of the transmit-

Black plate (116,1)

6. When you have finished entering the number, push the “ ” side of the locking switch within 5 seconds. NOTE . An electronic tone will sound. . If you push the “ ” side of the locking switch when more than 5
seconds have passed, an error will occur. In this event, perform the proce- dure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3. 7. Perform parts 5 and 6 of the procedure for each of the transmitter code beginning with the sec- ond digit (counting from the left) and finishing with the eighth digit.

the remaining digits of

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

NOTE . When you finish entering the eighth digit, an electronic tone will sound for 30 seconds. . If the interval between one push of the switch and the next exceeds 5
seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3. 8. Before the electronic tone stops sounding, use the power door locking switch to reenter the transmitter code beginning with the leftmost digit. NOTE If you do not start entering the number using the lock knob before the electro- nic tone stops sounding, an error will occur. In this event, perform the proce- dure again beginning with part 3. 9. When you have finished entering the code a second time, an electronic tone will sound for 1 second and automatic door locking and unlocking operation will take place once to indicate completion of registration, provided the code entered the second time is identical to that entered the first time.

NOTE If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3. 10. If you wish to program another trans- mitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure begin- ning with part 4. When you have finished programming all of the necessary trans- mitter codes into the system, remove the key from the ignition switch. 11. Test every registered transmitter confirm correct operation.

to

! Deleting old transmitter codes The control unit of the remote keyless entry system has four memory locations to store transmitter codes, giving it the ability to operate with up to four transmitters. When you lose a transmitter, the lost transmitter’s code remains in the memory. For security reasons, transmitter codes should be deleted from the mem- ory. To delete old transmitter codes, program four transmitter codes into the system. If

lost

Black plate (117,1)

Keys and doors 2-15

four times.

transmitter, you have only one current If you have two program it current transmitters, program each one twice. If you have three current transmit- ters, program two of them once and the third one twice. This process will leave only current transmitter codes in the system’s memory. NOTE Make sure no one else is operating their keyless entry system within range of your vehicle when programming transmitters. If someone else were to operate their remote transmitter while you are programming your transmit- ters, it is possible that their transmitter code will be programmed into your system, allowing them unauthorized access to your vehicle.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Black plate (118,1)

up to 30 seconds. The alarm is triggered by: . Opening any of the doors or the rear gate . Physical impact to the vehicle, such as forced entry (only vehicles with shock sensors (dealer option)) NOTE The alarm system can be set to trigger the illumination of the following interior lights. . Dome light (illuminates only when the dome light switch is in the “DOOR” position) . Map lights

The notifications regarding the dome light and the map lights are deactivated as the factory setting. A SUBARU dealer can activate the system. Contact your SUBARU dealer for details.

& Activating and deactivating

the alarm system

doors and the rear gate. 3. Turn the ignition switch to the “ON” position. 4. Hold down the UNLOCK side of the driver’s power door locking switch, open the driver’s door within the following 1
second, and wait 10 seconds without releasing the switch. The setting will then be changed as follows.

If the system was previously activated: The odometer/trip meter screen displays “AL oF” and the horn sounds twice, indicating that the system is now deacti- vated.

If the system was previously deacti- vated: The odometer/trip meter screen displays “AL on” and the horn sounds once, indicating that the system is now acti- vated. NOTE You may have the above setting change done by your SUBARU dealer.

To change the setting of your vehicle’s alarm system for activation or deactiva- tion, do the following. 1. Disarm the alarm system. Refer “Disarming the system” F2-18. 2. Sit

in the driver’s seat and shut all

to

2-16 Keys and doors

Alarm system

The alarm system helps to protect your vehicle and valuables from theft. The horn sounds and the turn signal lights flash if someone attempts to break into your vehicle.

The system can be armed and disarmed with the remote transmitter. The system does not operate when the key is inserted into the ignition switch. Your vehicle’s alarm system has been set for activation at the time of shipment from the factory. You can set the system for deactivation yourself or have it done by your SUBARU dealer.

& System operation The alarm system will give the following alarms when triggered. . The vehicle’s horn will sound for 30
seconds. . The turn signal seconds.

lights will flash for 30

If any of the doors or the rear gate remains open after the 30-second period, the horn will continue to sound for a maximum of 3
minutes. If any of the doors or the rear gate is closed while the horn is sounding, the horn will stop sounding with a delay of

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

& If you have accidentally trig-

gered the alarm system

! To stop the alarm Do any of the following operations. . Press any button on the remote trans- mitter. . Turn the ignition switch to the “ON” position.

& Arming the system ! To arm the system using remote

transmitter

1. Close all windows and the moonroof. 2. Remove the key from the ignition switch. 3. Open the doors and get out of vehicle. 4. Make sure that locked. 5. Close all doors and the rear gate.

the engine hood is

the

Black plate (119,1)

Keys and doors 2-17

once and the indicator lights will start flashing rapidly. After rapid flashing for 30
seconds (standby time), the indicator lights will then flash slowly (twice approxi- mately every 2 seconds), indicating that the system has been armed for surveil- lance.

If any of the doors or the rear gate is not fully closed, an electronic chirp sounds five times, the turn signal lights flash five times to alert you that the doors or the rear gate are not properly closed. When you close the door, the system will automati- cally arm and doors will automatically lock. ! To arm the system using power

door locking switches

: Press to Arm the system. : Press to Disarm the system.

1. Close all windows. 2. Remove the key from the ignition switch. 3. Open the doors and get out of vehicle. 4. Make sure that locked. 5. Close the doors and the rear gate but leave only the driver’s door or the front passenger’s door open.

the engine hood is

the

6. Briefly press the “ ” button (for less than 2 seconds). All doors and the rear gate will lock, an electronic chirp will sound once, the turn signal lights will flash

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

2-18 Keys and doors

6. Push the front side (“LOCK” side) of the power door locking switch to set the door locks. 7. Close the door. An electronic chirp will sound once, the turn signal lights will flash once and the indicator lights will start flashing rapidly. After rapid flashing for 30
seconds (standby time), the indicator lights will then flash slowly (twice approxi- mately every 2 seconds), indicating that the system has been armed for surveil- lance.

NOTE . The system can be armed even if the engine hood, the windows and/or moonroof are opened. Always make sure that they are fully closed before arming the system.

. The 30-second standby time can be eliminated if you prefer. Have it per- formed by your SUBARU dealer. . The system is in the standby mode for a 30-second period after locking the doors with the remote transmitter. The security indicator light will flash at short intervals during this period. . If any of the following actions is done during the standby period, the system will not switch to the surveil- lance state.

– Doors are unlocked using the remote transmitter. – Any of the doors or the rear gate is opened. – Ignition switch is turned to the “ON” position.

& Disarming the system Briefly press the “ ” button (for less than 2 seconds) on the remote transmitter. The driver’s door will unlock, an electronic chirp will sound twice and the turn signal lights will flash twice. The flashing of the security indicator light will then change slowly (once approximately every 3 sec- onds from twice approximately every 2
seconds), indicating that the alarm system has been disarmed.

To unlock all other doors and the rear gate, briefly press the “ ” button a

Black plate (120,1)

second time within 5 seconds. NOTE If the interval between the first and second presses of the “ ” button (for unlocking of all of the doors and the rear gate) is extremely short, the sys- tem may not respond. ! Emergency disarming If you cannot disarm the system using the transmitter is lost, broken or the transmitter battery is too weak), you can disarm the system without using the transmitter. The system can be disarmed if you turn the ignition switch from the “LOCK” to the “ON” position with a registered key.

the transmitter

(i.e.

& Valet mode When you choose the valet mode, the alarm system does not operate. In valet mode, the remote transmitter is used only for locking and unlocking the doors and rear gate and panic activation.

To enter the valet mode, change the setting of your vehicle’s alarm system for deactivation mode. Refer to “Activating and deactivating the alarm system” F2- 16. The security indicator light will con- tinue to flash once every 3 seconds indicating that the system is in the valet

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

mode.

To exit valet mode, change the setting of your vehicle’s alarm system for activation mode. Refer to “Activating and deactivat- ing the alarm system” F2-16.

& Passive arming When passive arming mode has been programmed by the dealer, arming of the system is automatically accomplished without using the remote transmitter. Note that in this mode, DOORS MUST BE MANUALLY LOCKED. ! To enter the passive mode If you wish to program the passive arming mode, have it done by your SUBARU dealer. ! Arming the system

CAUTION

In passive mode, the system will automatically activate the alarm but WILL NOT automatically lock the doors. In order to lock the doors you must either lock them as in- dicated in step 4 below or with the key once they have been closed. Failure to lock the doors manually will result in a higher security risk.

Black plate (121,1)

1. Turn the ignition switch to the “ON” position.

Keys and doors 2-19

LOCK

1) 2) ON

2. Turn the ignition switch from “ON” to “LOCK” position and remove the key from the ignition switch. 3. Open the doors and get out of vehicle.

the

4. Before closing the doors, lock all doors with the inside door lock levers. 5. Close the doors. The system will automatically arm after 1 minute.

In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door locking switch is used to lock the vehicle, arming will take place immediately regard- less of whether or not the passive mode has been selected. ! Disarming the system To disarm the system, briefly press the “

” button on the transmitter.

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

2-20 Keys and doors

& Tripped sensor identification The security indicator light flashes when the alarm system has been triggered. Also, the number of flashes indicates the location of unauthorized intrusion or the severity of impact on the vehicle.

the indicator

When the ignition switch is turned to the “ON” position, light will illuminate for 1 second and then flash as follows. . When a door or rear gate was opened: 5 times . When the ignition switch was turned to the “ON” position by using a key not registered with your immobilizer system: 3
times . When a strong impact or multiple impacts were sensed: twice (only vehicles with shock sensors (dealer option)) . When a light impact was sensed: once (only vehicles with shock sensors (dealer option)) NOTE Any of the above indicator light flash- ing patterns will recur each time the ignition switch is turned to the “ON” position. Rearming the alarm system cancels the flashing pattern of the security indicator light.

& Shock sensors (dealer op-

tion)

The shock sensors trigger the alarm system when they sense impacts applied to the vehicle and when any of their electric wires is cut. The alarm system causes the horn to sound and the turn signal lights to flash for a short time when the sensed impact is weak, but it warns of a strong impact or multiple impacts by sounding the horn and flashing the turn signal lights, both lasting approximately 30
seconds. If you desire, your SUBARU dealer can connect them and set them for activation or deactivation. NOTE . The shock sensors are not always able to sense impacts caused by break- ing in, and cannot sense an impact that does not cause vibration (such as breaking the glass using a rescue hammer). . The shock sensors may sense vi- bration like those shown in the follow- ing list and trigger the alarm system. Select the settings of the alarm system and shock sensors appropriately de- pending on where you usually park your vehicle.

Black plate (122,1)

Example:

– Vibration from construction site – Vibration in multistory car park – Vibration from trains

. You can have the sensitivity of the shock sensors adjusted to your pre- ference by your SUBARU dealer.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Child safety locks

WARNING

Always use the child safety lock whenever a child rides in the rear. Serious injury could result if a child accidentally opened the door and fell out.

Each rear door has a child safety lock that prevents the door from being opened even if the inside door handle is pulled.

When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever. The door can only be opened from the outside.

Windows & Power windows

WARNING

To avoid serious personal injury caused by entrapment, always con- form to the following instructions without exception. . When operating the power win- dows, be extremely careful to prevent anyone’s fingers, arms, neck or head from being caught in the window.

. Always lock the passengers’ win- dows using the lock switch when children are riding in the vehicle. . Before leaving the vehicle, al- ways remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operat- ing the power window.

The power windows operate only when the ignition switch is in the “ON” position.

Black plate (123,1)

Keys and doors 2-21

! Driver’s side switches

1) 2) 3) 4) 5)

Lock switch For driver’s window For front passenger’s window For rear left window For rear right window

All door windows can be controlled by the power window switch cluster at the driver side door.

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Black plate (124,1)

To open: Push the appropriate switch down and hold it until the window reaches the desired position.

To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held. ! Operating the passengers’ windows

To close: Pull the switch up and hold it until window reaches the desired position.

the

2-22 Keys and doors

! Operating the driver’s window

1) Open 2) Automatically open

To open: Push the switch down lightly and hold it. The window will open as long as the switch is held.

This switch also has a one-touch auto down feature that allows the window to be opened fully without holding the switch. Push the switch down until it clicks and release it, and the window will fully open. To stop the window halfway, pull the switch up lightly.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

! Locking the passengers’ windows

! Passengers’ side switches

Front passenger’s window switch 1) Open 2) Close

Push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ windows cannot be opened or closed. Press the switch again to cancel passengers’ window locking. NOTE When the lock switch is pushed to the “LOCK” position, the indicator lights in the passenger’s window switches (in- cluded in the power window switch cluster on the driver’s door) all turn off.

the

Black plate (125,1)

Keys and doors 2-23

Rear passengers’ window switches 1) Open 2) Close

To open: Push the switch down and hold it until the window reaches the desired position. To close: Pull the switch up and hold it until window reaches the desired position.

the

When the lock switch on the power window switch cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’ windows cannot be operated with the passengers’ switches.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

2-24 Keys and doors

Rear gate

To close: Lower the rear gate slowly and push down firmly until the latch engages. The rear gate can be lowered easily if you pull it down holding the recessed grip.

The rear gate can be locked and unlocked using any of the following systems. . Power door locking switch: Refer to “Power door locking switches” F2-7. . Remote keyless entry system (if equipped): Refer to “Remote keyless entry system” F2-8. To open: First unlock the rear gate lock then push the button.

Black plate (126,1)

WARNING

. To prevent dangerous exhaust gas from entering the vehicle, always keep the rear gate closed while driving.

. Do not attempt to shut the rear gate while holding the recessed grip. Also avoid closing the rear gate by pulling on the recessed grip from inside the cargo space. There is a danger of your hand being caught and injured.

CAUTION

. Do not jam a plastic bag in or place cellophane tape on the rear gate stays or scratch the stays while loading or unloading cargo. That could cause leakage of gas from the stays, which may result in their inability to hold the rear gate open.

. Be careful not to hit your head or face on the rear gate when open- ing or closing the rear gate and when loading or unloading car- go.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

NOTE If the rear gate cannot be unlocked due to a discharged vehicle battery, a malfunction in the door locking/unlock- ing system or other causes, you can unlock it by manually operating the rear gate lock release lever. For the procedure, refer to “Rear gate – if the rear gate cannot be unlocked” F9-18.

Moonroof (if equipped)

WARNING

Never let anyone’s hands, arms, head or any objects protrude from the moonroof. A person could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is involved in an accident. To avoid serious personal injury caused by entrapment, always con- form to the following instructions without exception. . Before closing the moonroof, make sure that no one’s hands, arms, head or other objects will be accidentally caught in the moonroof.

. Before leaving the vehicle, al- ways remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operat- ing the moonroof.

Black plate (127,1)

Keys and doors 2-25

. Never try to check the anti-en- trapment function by deliberately placing part of your body in the moonroof.

CAUTION

. Do not sit on the edge of the open

moonroof.

. Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut.

. The anti-entrapment

function does not operate when the moon- roof is being tilted down. Be sure to confirm that it is safe to do so before tilting the moonroof down.

The moonroof has both tilting and sliding functions.

The moonroof operates only when the ignition switch is in the “ON” position.

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

2-26 Keys and doors

& Tilt function

NOTE One-touch operation does not take place when the moonroof is raised or lowered. Push the switch continuously to raise or lower the moonroof.

& Sliding function

Tilt switch

1) 2) Raise 3) Lower

The tilting function will only operate when the moonroof is fully closed. Push the rear side of the “Tilt” switch to raise the moonroof. Push the front side of the “Tilt” switch to lower the moonroof.

Release the switch after the moonroof has been raised or has been lowered com- pletely. Pushing the switch continuously may cause damage to the moonroof.

1) Open/Close switch 2) Open 3) Close

Push the “Open/Close” switch rearward to open the moonroof. The sun shade will also be opened together with the moon- roof. Push the “Open/Close” switch forward to close the moonroof. The moonroof will stop halfway. Push it again to close the moonroof completely.

Black plate (128,1)

To stop the moonroof at a selected mid- way position while opening or closing it, momentarily push the switch to the “OPEN” or “CLOSE” side. After washing the vehicle or after it rains, wipe away water on the roof prior to opening the moonroof to prevent drops of water from falling into the passenger compartment.

& Anti-entrapment function When the moonroof senses a substantial enough object trapped between its glass and the vehicle’s roof during closure, it automatically moves back to either of the following positions according to the point at which it senses the object. . When the moonroof senses the object at a point between the halfway stop position and fully closed position, it moves back to the halfway stop position and stops there. . When the moonroof senses the object at a point between the halfway stop position and fully open position, it moves back to the fully open position and stops there.

The anti-entrapment function may also be activated by a strong shock on the moon- roof even when there is nothing trapped.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

CAUTION

Never attempt to test this function using fingers, hands or other parts of your body.

NOTE For the sake of safety, it is recom- mended that you avoid driving with the moonroof fully opened.

& Sun shade

The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.

Black plate (129,1)

Keys and doors 2-27

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Black plate (2,1)

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Left Page

Model "ALL_MODEL_MEMO" EDITED: 2007/ 6/ 22

3-3
3-3
3-4
3-4
3-4
3-4
3-4
3-5
3-5
3-5

Ignition switch ..................................................... LOCK.................................................................. Acc..................................................................... ON...................................................................... START ................................................................ Key reminder chime ............................................ Ignition switch light ............................................. Hazard warning flasher....................................... Meters and gauges.............................................. Combination meter illumination ........................... Canceling the function for meter needle/gauge movement and combination meter sequential illumination upon turning on the ignition switch............................................................... Speedometer....................................................... Odometer............................................................ Double trip meter ................................................ Tachometer ......................................................... Fuel gauge.......................................................... Temperature gauge ............................................. Warning and indicator lights ..............................

3-5
3-6
3-6
3-7
3-7
3-8
3-9
3-9
Seatbelt warning light and chime ........................ 3-10
SRS airbag system warning light ........................ 3-11
Front passenger’s frontal airbag ON and OFF indicators......................................................... 3-12

CHECK ENGINE warning light/Malfunction

indicator lamp .................................................. 3-12
Charge warning light .......................................... 3-13
Oil pressure warning light .................................. 3-13
AT OIL TEMP warning light ................................. 3-13

Black plate (5,1)

Instruments and controls

Rear differential oil temperature warning

light ................................................................ Low tire pressure warning light .......................... ABS warning light.............................................. Brake system warning light................................ Low fuel warning light ....................................... Door open warning light .................................... Windshield washer fluid warning light ................ All-Wheel Drive warning light ............................. Vehicle Dynamics Control operation indicator

light ................................................................ Vehicle Dynamics Control warning light/Traction Control system OFF indicator light ................... Security indicator light....................................... SPORT mode indicator light ............................... Select lever/Gear position indicator .................... Turn signal indicator lights................................. High beam indicator light ................................... Cruise control indicator light.............................. Cruise control set indicator light ........................ Headlight indicator light ..................................... Front fog light indicator light.............................. Clock .................................................................. Outside temperature indicator .......................... Low outside temperature warning ......................

Multi function display (vehicles without a

genuine SUBARU navigation system)........... Current fuel consumption .................................. Average fuel consumption ................................. Driving range on remaining fuel ......................... Journey time .....................................................

3-14
3-14
3-15
3-16
3-17
3-17
3-18
3-18

3-18

3-18
3-19
3-20
3-20
3-20
3-20
3-20
3-21
3-21
3-21
3-21
3-22
3-22

3-23
3-23
3-24
3-24
3-25

北米Model "A3160BE-C" EDITED: 2010/ 11/ 17

Black plate (6,1)

Instruments and controls

Light control switch ........................................... 3-26
Headlights.......................................................... 3-26
High/low beam change (dimmer)......................... 3-27
Headlight flasher ................................................ 3-27
Daytime running light system ............................. 3-27
Turn signal lever ................................................ 3-28
Illumination brightness control ......................... 3-28
Headlight beam leveler (if equipped) ................ 3-29
Parking light switch ........................................... 3-31
Front fog light switch......................................... 3-31

Wiper and washer.............................................. Windshield wiper and washer switches .............. Rear window wiper and washer switch ............... Windshield wiper deicer.................................... Rear window defogger button .......................... Mirrors ................................................................ Type A inside mirror (if equipped) ...................... Type B inside mirror (if equipped) ...................... Type C inside mirror (if equipped) ...................... Outside mirrors ................................................. Tilt steering wheel ............................................. Horn....................................................................

3-32
3-33
3-34
3-35
3-36
3-37
3-37
3-37
3-40
3-41
3-43
3-43

北米Model "A3160BE-C" EDITED: 2010/ 11/ 17

Ignition switch

WARNING

. Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.

. Before leaving the vehicle, al- ways remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child or others. Children could operate the power windows, the moon- roof or other controls or even make the vehicle move.

CAUTION

Do not attach a large key holder or key case to either key. If it banged against your knees or hands while you were driving, it could turn the ignition switch from the “ON” posi-

Black plate (133,1)

if

tion to the “Acc” or “LOCK” posi- tion, thereby stopping the engine. Also, the key is attached to a keyholder or to a large bunch of other keys, centrifugal force may act on it as the vehicle moves, resulting in unwanted turning of the ignition switch.

The ignition switch has four positions: LOCK, Acc, ON and START.

Instruments and controls 3-3

. If the ignition switch will not move from the “LOCK” position to the “Acc” position, turn the steering wheel slightly to the left and right as you turn the ignition switch.

& LOCK The key can only be inserted or removed in this position. The ignition switch will lock the steering wheel when you remove the key. If turn the steering wheel slightly to the right and left as you turn the key.

turning the key is difficult,

NOTE . Keep the ignition switch in the “LOCK” position when the engine is not running. . Using electrical accessories for a long time with the ignition switch in the “ON” or “Acc” position can cause the battery to go dead.

The key can be turned from “Acc” to “LOCK” only when the select lever is in the “P” position.

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

3-4 Instruments and controls

& Acc In this position the electrical accessories (radio, accessory power outlet, etc.) can be used.

& ON This is the normal operating position after the engine is started.

& START

CAUTION

Do not turn the ignition switch to the “START” position while the engine is running.

The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position.

If your registered key fails to start the engine, pull out the key once (the security indicator light will blink), and then insert the key in the ignition switch and turn it to the “START” position and again try to start the engine.

Black plate (134,1)

NOTE The engine may not start in the follow- ing cases.

contains an immobilizer transponder. . The key is near or touching another transmitter.

& Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “Acc” positions. The chime stops when the key is removed from the ignition switch.

& Ignition switch light For easy access to the ignition switch in the dark, the ignition switch light illumi- nates when the driver’s door is opened. The light remains on for several seconds and then gradually turns off after driver’s door is closed. Also, turns off immediately if the key is turned to the “ON” position.

the light

. The key grip is touching another key or a metallic key holder.

. The key is near another key that

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Hazard warning flasher

Meters and gauges

NOTE Liquid crystal displays are used in some of the meters and gauges on the combination meter. You will find their indications hard to see if you wear polarized glasses.

& Combination meter illumina-

tion

the various parts of

When the ignition switch is turned to the “ON” position, the combination meter are illuminated in the following sequence. 1. Warning lights, indicator lights, meter rims, meter needles, odometer, trip meter, and gauge back lights illuminate. 2. Meter needles and gauges each show MAX reading. 3. Meter needles and gauges each show MIN reading. 4. Meter and gauge dials illuminate. 5. Regular illumination (for driving) be- gins.

NOTE The above sequence of operations may not take place if you quickly turn the

The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions. The hazard warning flasher works with the ignition switch in any position.

To turn on the hazard warning flasher, push the hazard warning button on the instrument panel. To turn off the flasher, push the button again. NOTE When the hazard warning flasher is on, the turn signals do not work.

Black plate (135,1)

Instruments and controls 3-5

ignition switch to start the engine. This is not a malfunction. & Canceling the function for meter needle/gauge move- ment and combination meter sequential illumination upon turning on the ignition switch

It is possible to activate or deactivate the movement of the meter needles and gauges and sequential illumination of the combination meter that takes place when the ignition switch is turned to the “ON” position. Turn the ignition switch to the “Acc” position. With the A trip meter indication selected, briefly press the trip knob twice. You can now establish the activated/ deactivated setting for movement of the – CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Black plate (136,1)

3-6 Instruments and controls

meter needles and gauges when the ignition switch is turned to the “ON” position. To change the current setting, press the trip knob for at least 2 seconds.

combination meter when the ignition switch is turned to the “ON” position. To change the current setting, press the trip knob for at least 2 seconds.

& Speedometer The speedometer shows the vehicle speed.

: Activated : Deactivated

: Activated : Deactivated

& Odometer

With the function deactivated, the combi- nation meter illuminates as follows. 1. Warning lights, indicator lights, meter rims, meter needles, odometer, trip meter, and gauge back lights illuminate. 2. Meter and gauge dials illuminate. 3. Regular illumination (for driving) be- gins.

Briefly press the trip knob again. You can now establish the activated/deactivated setting for sequential the

illumination of

Briefly press the knob to return to the A trip meter indication.

If you turn the ignition switch to the “LOCK” position, turn the ignition switch to the “ON” position, or open and close the driver’s door during the setting procedure, the new setting will be canceled. Also, if you do not press the trip knob for a period of 10 seconds, the new setting will be canceled. NOTE . It is not possible to cancel sequen- tial the combination meter while sequential illumination is actually taking place. Cancel sequen- tial illumination when regular illumina- tion (for driving) has begun. . When you open the driver’s door with the ignition switch in the “LOCK” position, the meters’ needles and rims are lit. The illumination stops working when you shut the driver’s door or automatically after 30 seconds.

illumination of

This meter displays the odometer when the ignition switch is in the “LOCK”, “Acc” or “ON” position. The odometer shows the total distance that the vehicle has been driven.

If you press the trip knob when the ignition switch is in the “LOCK” or “Acc” position, the odometer/trip meter will light up. If you do not press the trip knob within 10
seconds of illumination of the odometer/ trip meter, the odometer/trip meter will turn off.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

The odometer/trip meter will also turn off if you open and close the driver’s door within 10 seconds of illumination of the odometer/trip meter.

& Double trip meter

This meter displays two trip meters when the ignition switch is in the “LOCK”, “Acc” or “ ON” position. The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the knob. Each press of the knob changes the mode indication alternately.

To set the trip meter to zero, select the A trip or B trip meter by pushing the knob and keep the knob pushed for more than 2
seconds.

It

If you press the trip knob when the ignition switch is in the “LOCK” position, the odometer/trip meter will light up. is possible to switch between the A trip meter and B trip meter indications while the odometer/trip meter is lit up. If you do not press the trip knob within 10 seconds of illumination of the odometer/trip meter, the odometer/trip meter will turn off. Also, if you open and close the driver’s door within 10 seconds of illumination of the odometer/trip meter, the odometer/trip meter will turn off.

CAUTION

To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result.

Black plate (137,1)

Instruments and controls 3-7

NOTE If the connection between the combina- tion meter and battery is broken for any reason such as vehicle maintenance or fuse replacement, the data recorded on the trip meter will be lost. ! Vehicle communication system

malfunction indication

”.

The vehicle communication system car- ries various types of information (vehicle speed, running conditions, etc.) to control modules. In the event of a malfunction in this communication system, the trip meter will show “ If the trip meter shows “ ”, immediately contact the nearest SUBARU dealer and have the vehicle communication system inspected. NOTE If you press the trip knob while the trip meter is showing “ ”, the trip meter indication will appear for 10 seconds.

& Tachometer The tachometer shows the engine speed in thousands of revolutions per minute.

CAUTION

Do not operate the engine with the

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

3-8 Instruments and controls

pointer of the tachometer in the red zone. This may cause severe da- mage to the engine.

NOTE To protect the engine while the select lever is in the “P” or “N” position, the engine is controlled so that the engine speed may not become too high even if the accelerator pedal is depressed hard.

& Fuel gauge

level movement in the tank. If you press the trip knob while the ignition switch is in the “LOCK” or “Acc” position, the fuel gauge will light up and indicate the amount of fuel remaining in the tank. NOTE

” sign in the fuel

You will see the “ gauge meter. This indicates that the fuel filler door (lid) is located on the right side of the vehicle.

The fuel gauge shows the approximate amount of fuel remaining in the tank.

The gauge may move slightly during braking, turning or acceleration due to fuel

Black plate (138,1)

! Low fuel warning light

CAUTION

Promptly put fuel in the tank when- ever the low fuel warning light illuminates. Engine misfires as a result of an empty tank could cause damage to the engine.

The low fuel warning light illuminates when the tank is nearly empty (approxi- mately 2.6 US gal [10 liters, 2.2 Imp gal]).

It only operates when the ignition switch is in the “ON” position. When this light illuminates, fill the fuel tank immediately. NOTE This light does not turn off unless the tank is replenished up to an internal fuel quantity of approximately 4.0 US gal (15 liters, 3.3 Imp gal).

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

Black plate (139,1)

Instruments and controls 3-9

& Temperature gauge

CAUTION

Warning and indicator lights

If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possible. Refer to “Engine overheating” F9- 14.

Several of the warning and indicator lights illuminate momentarily and then turn off when the ignition switch is initially turned to the “ON” position. This permits check- ing the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position. The following lights illuminate.

1) Normal operating range

The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position.

The coolant temperature will vary in accordance with the outside temperature and driving conditions.

We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range. Also, high revving operation while the engine is not sufficiently warmed up should be avoided.

: Driver’s seatbelt warning light (The seatbelt warning light only when the driver seatbelt.) : Front passenger’s seatbelt warning

turns off fastens the

light (The seatbelt warning light turns off only when the front seat passenger fastens the seatbelt.)

: SRS airbag system warning light

: CHECK ENGINE warning light/Mal-

function indicator lamp

: Charge warning light

: Oil pressure warning light

: AT OIL TEMP warning light

: ABS warning light

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

for repair. & Seatbelt warning light

and chime

Your vehicle is equipped with a seatbelt warning device at the driver’s and front passenger’s seat. With the ignition switch turned to the “ON” position, this device reminds the driver and front passenger to fasten their seat- belts by illuminating the warning lights in the locations indicated in the following illustrations and sounding a chime.

3-10 Instruments and controls

: Vehicle Dynamics Control operation

indicator light

: Vehicle Dynamics Control warning light/Traction Control system OFF indicator light

: Brake system warning light

: AWD warning light

: Low tire pressure warning light

: SPORT mode indicator light

: Front passenger’s frontal airbag ON

indicator light

: Front passenger’s frontal airbag OFF

indicator light

: Low fuel warning light

: Cruise control indicator light

: Cruise control set indicator light

: Rear differential oil temperature warn- ing light

: Windshield washer fluid warning light

: Door open warning light

Driver’s warning light

If any lights do not illuminate, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer

Black plate (140,1)

Front passenger’s warning light ! Operation If the driver and/or front passenger have/ has not yet fastened the seatbelt(s) when the ignition switch is turned to the “ON” position, the seatbelt warning light(s) will flash for 6 seconds, the seatbelt(s) is/are unfastened. the dri- ver’s seatbelt is not fastened, a chime will also sound simultaneously. NOTE . If the driver’s and/or front passen- ger’s seatbelt(s) is/are still not fastened 6 seconds later, the seatbelt warning device operates as follows according to the vehicle speed.

to warn that

If

– At speeds lower than approxi- mately 9 mph (15 km/h)

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

The warning light(s) for unfastened seatbelt(s) will alternate between steady illumination and flashing at 15-second intervals. The chime will not sound. – At speeds higher than approxi- mately 9 mph (15 km/h) The warning light(s) for unfastened seatbelt(s) will alternate between flashing and steady illumination at 15-second intervals and the chime will sound while the warning light(s) is/are flashing.

time, however,

. It is possible to cancel the warning operation that follows the 6-second warning after turning ON the ignition switch. When the ignition switch is turned ON next the complete sequence of the warning operation resumes. For further details about canceling the warning operation, please contact your SUBARU dealer. there is no passenger on the front If passenger’s seat, the seatbelt warning device for the front passenger’s seat will be deactivated. The front passenger’s occupant detection system monitors whether or not there is a passenger on the front passenger’s seat. Observe the following precautions. Failure to do so may prevent the device from functioning correctly or cause the device to fail.

. Do not install any accessory such as a table or TV onto the seatback. . Do not store a heavy load in the seatback pocket. . Do not allow the rear seat occupant to place his/her hands or legs on the front passenger’s seatback, or allow him/her to pull the seatback.

If the seatbelt warning device for the front passenger’s seat does not function cor- rectly (e.g., it is activated even when the front passenger’s seat is empty or it is deactivated even when the front passen- ger has not fastened his/her seatbelt), take the following actions. . Ensure that no article is placed on the seat other than a child restraint system and its child occupant. . Ensure that there is no article left in the seatback pocket.

If still the seatbelt warning device for front passenger’s seat does not function cor- rectly after taking relevant corrective ac- tions described above, immediately con- tact your SUBARU dealer for an inspec- tion.

Black plate (141,1)

Instruments and controls 3-11

& SRS airbag system

warning light

When the ignition switch is turned to the “ON” position, the SRS airbag system warning light will illuminate for approxi- mately 6 seconds and turn off. This shows the SRS frontal airbag and SRS side airbag and SRS curtain airbag and seat- belt pretensioners are in normal operation.

WARNING

If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pretensioners and/or SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbags will operate improperly (e.g. SRS airbags may inflate in a very minor collision or not inflate in a severe collision), which may in- crease the risk of injury. . Flashing or flickering of the warn-

ing light

. No illumination of

the warning light when the ignition switch is first turned to the “ON” position

– CONTINUED –

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

3-12 Instruments and controls

. Continuous illumination of

warning light

the

. Illumination of the warning light

while driving

& Front passenger’s frontal

airbag ON and OFF indica- tors

: Front passenger’s frontal airbag ON indicator : Front passenger’s frontal airbag OFF indicator

The front passenger’s frontal airbag ON and OFF indicators show you the status of the front passenger’s SRS frontal airbag. The indicators are located in the center portion of the dashboard.

When the ignition switch is turned to the “ON” position, both the ON and OFF indicators illuminate for 6 seconds during which time the system is checked. Follow- ing the system check, both indicators turn off for 2 seconds. After that, one of the indicators illuminates depending on the status of the front passenger’s SRS frontal airbag determined by the SUBARU ad- vanced frontal airbag system monitoring. If the front passenger’s SRS frontal airbag is activated, the passenger’s frontal airbag ON indicator will illuminate while the OFF indicator will remain off. If the front passenger’s SRS frontal airbag the passenger’s frontal is deactivated, airbag ON indicator will remain off while the OFF indicator will illuminate. If both the ON and OFF indicators remain illuminated or off simultaneously, the system is malfunctioning. Contact your SUBARU dealer immediately for an in- spection.

Black plate (142,1)

& CHECK ENGINE warn- ing light/Malfunction in- dicator lamp

CAUTION

If the CHECK ENGINE light illumi- nates while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possible. Continued vehicle opera- tion without having the emission control system checked and re- paired as necessary could cause serious damage, which may not be covered by your vehicle’s warranty.

If this light illuminates steadily or blinks while the engine is running, it may indicate that there is a problem or potential problem somewhere in the emission con- trol system. ! If the light illuminates steadily If the light illuminates steadily while driving or does not turn off after the engine starts, an emission control system malfunction has been detected. You should have your vehicle checked by an authorized SUBARU dealer immedi- ately.

北米Model "A3160BE-C" EDITED: 2010/ 11/ 19

turn off,

NOTE This light also illuminates when the fuel filler cap is not tightened until it clicks. If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indicator lamp illuminat- ing could be a loose or missing fuel filler cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK ENGINE warning light turn off immediately. It may take several driving trips. If the light does not take your vehicle to your authorized SUBARU dealer immediately. ! If the light is blinking If is blinking while driving, an engine misfire condition has been de- tected which may damage the emission control system. To prevent serious damage to the emis- sion control system, you should do the following. . Reduce vehicle speed. . Avoid hard acceleration. . Avoid steep uphill grades. . Reduce the amount of cargo, if possi- ble. . Stop towing a trailer as soon as possible.

the light

The CHECK ENGINE warning light may stop blinking and illuminate steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately. & Charge warning light If this light illuminates when the engine is running, it may indicate that the charging system is not working properly.

If the light illuminates while driving or does not turn off after the engine starts, stop the the first safe opportunity and engine at check the alternator belt. is the belt loose, broken or if is in good condition but the light remains illuminated, contact your nearest SUBARU dealer immediately. & Oil pressure warning

If the belt

light

CAUTION

Do not operate the engine with the oil pressure warning light illumi- nated. This may cause serious en- gine damage.