2007 Subaru Legacy Owners Manual

Black plate (387,1)

Maintenance and service 11-39

Vehicles equipped with 4 non-unidirec- tional tires 1)

Front

Tire wear varies from wheel to wheel. To maximize the life of each tire and ensure that the tires wear uniformly, it is best to rotate the tires every 7,500 miles (12,500
km). Move the tires to the positions shown in the applicable illustration each time they are rotated. Replace any damaged or unevenly worn tire at tire rotation, adjust the tire pressures and make sure the wheel nuts are correctly tightened.

rotation. After

the time of

After driving approximately 600 miles (1,000 km), check the wheel nuts again and retighten any nut that has become loose.

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

11

Black plate (388,1)

WARNING

WARNING

Use only those wheels that are specified for your vehicle. Wheels not meeting specifications could interfere with brake caliper opera- tion and may cause the tires to rub against the wheel well housing dur- ing turns. The resulting loss of vehicle control could lead to an accident.

. All four tires must be the same in terms of manufacturer, brand (tread pattern), construction, de- gree of wear, speed symbol, load index and size. Mixing tires of different types, sizes or degrees of wear can result in damage to the vehicle’s power train. Use of different types or sizes of tires can also dangerously reduce controllability and braking per- formance and can lead to an accident.

. Use only radial tires. Do not use radial tires together with belted bias tires and/or bias-ply tires. Doing so can dangerously re- duce controllability, resulting in an accident.

& Wheel replacement When replacing wheels due, for example, to damage, make sure the replacement wheels match the specifications of the wheels that are fitted as standard equip- ment. Replacement wheels are available from SUBARU dealers.

11-40 Maintenance and service

& Tire replacement The wheels and tires are important and integral parts of your vehicle’s design; they cannot be changed arbitrarily. The tires fitted as standard equipment are optimally matched to the characteristics of the vehicle and were selected to give the best possible combination of running performance, ride comfort, and service life. It is essential for every tire to have a size and construction matching those shown on the tire placard and to have a speed symbol and load index matching those shown on the tire placard.

Using tires of a non-specified size detracts from controllability, ride comfort, braking performance, speedometer accuracy and odometer accuracy. It also creates incor- rect body-to-tire clearances and inappro- priately changes the vehicle’s ground clearance.

All four tires must be the same in terms of manufacturer, brand (tread pattern), con- struction, and size. You are advised to replace the tires with new ones that are identical to those fitted as standard equip- ment.

For safe vehicle operation, SUBARU recommends replacing all tires at the same time.

four

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Aluminum wheels

Windshield washer fluid

Black plate (389,1)

Maintenance and service 11-41

Aluminum wheels can be scratched and damaged easily. Handle them carefully to maintain their appearance, performance, and safety. . When any of the wheels is removed and replaced for tire rotation or to change a flat, always check the tightness of the wheel nuts after driving approximately 600
miles (1,000 km). is loose, If any nut tighten it to the specified torque. . Never apply oil to the threaded parts, wheel nuts, or the wheel. . Never let the wheel rub against sharp protrusions or curbs. . Be sure to fit tire chains on uniformly and completely around the tire, otherwise the chains may scratch the wheel. . When wheel nuts, balance weights, or the center cap is replaced, be sure to replace them with genuine SUBARU parts designed for aluminum wheels.

tapered surface of

CAUTION

Never use engine coolant as washer fluid because it could cause paint damage.

Washer fluid level gauge

If you spray washer fluid on the windshield but the supply of washer fluid appears to diminish, check the level of washer fluid in the tank.

11

Remove the washer tank filler cap, then check the fluid level indicated by the level gauge (attached to the inside of the cap). is near the “Low” mark, add If the level fluid until it reaches the “Hi” level on the

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

temperature, it may freeze and block the nozzles.

CAUTION

Adjust the washer fluid concentra- tion appropriately for the outside temperature. If the concentration is inappropriate, sprayed washer fluid may freeze on the windshield and obstruct your view, and the fluid may freeze in the reservoir tank.

11-42 Maintenance and service

level gauge or the “Full” mark on the tank. Use windshield washer fluid. If windshield washer fluid is unavailable use clean water. In areas where water freezes in winter, use an anti-freeze type windshield washer fluid. SUBARU Windshield Washer Fluid contains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing tem- perature varies according to how much it is diluted, as indicated in the following table.

Washer Fluid Concentration

30%

50%

100%

Freezing

Temperature 10.48F (−128C) −48F (−208C) −498F (−458C)

In order to prevent freezing of washer fluid, check the freezing temperatures in the table above when adjusting the fluid concentration to the outside temperature. If you fill the reservoir tank with a fluid with a different concentration from the one used previously, purge the old fluid from the piping between the reservoir tank and washer nozzles by operating the washer for a certain period of time. Otherwise, if the concentration of the fluid remaining in the piping is too low for the outside

Black plate (390,1)

Replacement of wiper blades

Grease, wax, insects, or other materials on the windshield or the wiper blade results in jerky wiper operation and streak- ing on the glass. If you cannot remove the streaks after operating the windshield washer or if the wiper operation is jerky, clean the outer surface of the windshield (or rear window) and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the windshield and wiper blades with clean water. The windshield is clean if beads do not form when you rinse the windshield with water.

CAUTION

. Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper blades.

. When you wish to raise the passenger-side wiper arm, first raise the driver-side wiper arm. Otherwise, the passenger-side wiper assembly and driver-side wiper assembly will touch each other, possibly resulting in scratches.

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

. Return the passenger-side wiper arm to its original position before returning the driver-side wiper arm to its original position. Otherwise, the passenger-side wiper assembly and driver-side wiper assembly will touch each other, possibly resulting in scratches.

If you cannot eliminate the streaking even after following this method, replace the wiper blades using the following proce- dures:

& Windshield wiper blade as-

sembly

1. Raise the windshield wiper arm on the driver’s side. 2. Next, raise the windshield wiper arm on the passenger’s side.

Black plate (391,1)

Maintenance and service 11-43

& Windshield wiper blade rub-

ber

1) Stopper

3. Remove the wiper blade assembly by holding its pivot area and pushing it in the direction shown by the arrow while de- pressing the wiper blade stopper. 4. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 5. Lower the windshield wiper arm on the passenger’s side slowly while supporting it by hand. 6. Next, lower the windshield wiper arm on the driver’s side slowly while support- ing it by hand.

1) Metal support

1. Grasp the locked end of the blade rubber assembly and pull it firmly until the stoppers on the rubber are free of the metal support.

11

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Black plate (392,1)

11-44 Maintenance and service

with the grooves in the rubber and slide the blade rubber assembly into the metal support until it locks.

& Rear window wiper blade

assembly

1. Raise the wiper arm off window.

the rear

1) Metal spines

2. If the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber.

1) Stopper

4. Be sure to position the claws at the end of the metal support between the stoppers on the rubber as shown. If the rubber is not retained properly, the wiper blade may scratch the windshield.

2. Turn the wiper blade assembly coun- terclockwise.

3. Align the claws of the metal support

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Black plate (393,1)

& Rear window wiper blade

rubber

2. Pull the blade rubber assembly out of the plastic support.

Maintenance and service 11-45

3. Pull the wiper blade assembly toward you to remove it from the wiper arm.

1. Pull out the end of the blade rubber assembly to unlock it from the plastic support.

1) Metal spines

3. If the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber.

11

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

11-46 Maintenance and service

ends. If the rubber is not retained properly, the wiper may scratch the rear window glass. 5. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 6. Hold the wiper arm by hand and slowly lower it in position.

4. Align the claws of the plastic support with the grooves in the blade rubber assembly, then slide the blade rubber assembly into place.

Securely retain both ends of the rubber with the stoppers on the plastic support

Black plate (394,1)

Battery

WARNING

. Before beginning work on or near any battery, be sure to extinguish all cigarettes, matches, and light- ers. Never expose a battery to an open flame or electric sparks. Batteries give off a gas which is highly flammable and explosive. . For safety, in case an explosion does occur, wear eye protection or shield your eyes when work- ing near any battery. Never lean over a battery.

. Do not let battery fluid contact eyes, skin, fabrics, or paint be- cause battery fluid is a corrosive acid. If battery fluid gets on your skin or in your eyes, immediately flush the area with water thor- oughly. Seek medical help imme- diately if acid has entered the eyes. If battery fluid is accidentally swallowed, immediately drink a large amount of milk or water, and seek medical attention im- mediately.

. To lessen the risk of sparks,

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

remove rings, metal watchbands, and other metal jewelry. Never allow metal tools to contact the positive battery terminal and any- thing connected to it WHILE you are at the same time in contact with any other metallic portion of the vehicle because a short cir- cuit will result.

. Keep everyone including children

away from the battery.

. Charge the battery in a well-

ventilated area.

. Battery posts, terminals, and re- lated accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Batteries also contain other chemicals known to the State of California to cause can- cer. Wash hands after handling.

CAUTION

Never use more than 10 amperes when charging the battery because it will shorten battery life.

It is unnecessary to periodically check the battery fluid level or periodically refill with

Black plate (395,1)

Maintenance and service 11-47

distilled water.

Fuses

CAUTION

Never replace a fuse with one hav- ing a higher rating or with material other than a fuse because serious damage or a fire could result.

The fuses are designed to melt during an overload to prevent damage to the wiring harness and electrical equipment. The fuses are located in two fuse boxes. One is located under the instrument panel behind the fuse box cover on the driver’s seat side.

11

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

11-48 Maintenance and service

Black plate (396,1)

Open the lid that is located above the hood release knob and pull it toward you to remove it.

The spare fuses are stored in the main fuse box cover in the engine compart- ment.

The other one is housed in the engine compartment.

The fuse puller is stored in the main fuse box in the engine compartment.

1) Good 2) Blown

inspect

If any lights, accessories or other electrical controls do not operate, the corresponding fuse. If a fuse has blown, replace it. 1. Turn the ignition switch to the “LOCK” position and turn off all electrical acces- sories. 2. Remove the cover. 3. Determine which fuse may be blown. The back side of each fuse box cover and the “Fuses and circuits” section in chapter 12 in this manual show the circuit for each fuse.

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

If

Inspect

the fuse.

4. Pull out the fuse with the fuse puller. 5. it has blown, replace it with a spare fuse of the same rating. 6. this indicates that its system has a problem. Contact your SUBARU dealer for repairs.

the same fuse blows again,

If

Main fuse

Main fuse box

The main fuses are designed to melt during an overload to prevent damage to the wiring harness and electrical equip- ment. Check the main fuses if any electrical component fails to operate (ex- cept the starter motor) and other fuses are good. A melted main fuse must be replaced. Use only replacements with the same specified rating as the melted main fuse. is replaced, have the electrical system checked by your nearest SUBARU dealer.

If a main fuse blows after

it

Black plate (397,1)

Maintenance and service 11-49

Installation of accessories

Always consult your SUBARU dealer before installing fog lights or any other electrical equipment in your vehicle. Such accessories may cause the electronic system to malfunction if they are incor- rectly installed or if they are not suited for the vehicle.

11

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Black plate (398,1)

11-50 Maintenance and service

Replacing bulbs

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

1) 2) 3) 4) 5) 6) 7)

High beam headlight Low beam headlight Front turn signal/Parking and front side marker light Map light Dome light Door step light Front fog light

Except OUTBACK

OUTBACK

Backup light (Sedan)

8) Trunk room light (Sedan) 9) High mount stop light (Sedan) 10) Rear turn signal light (Sedan) 11) 12) Brake/tail and rear side marker light (Sedan) 13) Cargo area light 14) Brake/tail light (Station wagon) 15) Rear side marker light (Station wagon) 16) Rear turn signal light (Station wagon) 17) Backup light (Station wagon) 18)

Licence plate light

Black plate (399,1)

Maintenance and service 11-51

Wattage

Bulb No.

CAUTION

12V-60W 12V-55W 12V-27/8W 12V-8W 12V-8W 12V-3.5W

12V-55W

12V-51W

12V-5W 12V-21W 12V-21W 12V-16W 12V-21/5W 12V-13W 12V-21/5W 12V-5W 12V-21W 12V-16W 12V-5W

9005 (HB3) H7
3157A –

–

–

H3

9006 (HB4)

–

(W21W) (W21W) 921
(W21/5W) –

(W21/5W) 168
(W21W) 921
168

Replace any bulb only with a new bulb of the specified wattage. Using a bulb of different wattage could result in a fire.

& Headlight

CAUTION

Halogen headlight bulbs become very hot while in use. If you touch the bulb surface with bare hands or greasy gloves, finger prints or grease on the bulb surface develop into hot spots, causing the bulb to break. If there are finger prints or grease on the bulb surface, wipe them away with a soft cloth mois- tened with alcohol.

NOTE . If headlight aiming is required, con- sult your SUBARU dealer for proper adjustment of the headlight aim. . It may be difficult to replace the bulbs. Have your SUBARU dealer re- place the bulbs if necessary.

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

11

11-52 Maintenance and service

! Low beam light bulbs

2. Use a screwdriver to remove the secured clip of the washer tank. To make it easy to access the bulb, move the washer tank to the horizontal direction. (left-hand side)

Right-hand side

1. Use a screwdriver to undo the clips on the air intake duct, then remove the air intake duct. (right-hand side)

3. Remove the bulb cover, by turning it counterclockwise.

Black plate (400,1)

4. Disconnect the electrical connector. 5. Remove the retainer spring. 6. Replace the bulb, then set the retainer spring securely. 7. Reconnect the electrical connector. 8. 9. (right-hand side) 10. Set the washer tank to the original place and secure it by clip. (left-hand side)

Install the bulb cover. Install

the air intake duct with clip.

Left-hand side

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

! High beam light bulbs

2. Use a screwdriver to remove the secured clip of the washer tank. To make it easy to access the bulb, move the washer tank to the horizontal direction. (left-hand side)

Right-hand side

1. Use a screwdriver to undo the clips on the air intake duct, then remove the air intake duct. (right-hand side)

Left-hand side

the electrical connector

3. Disconnect from the bulb. 4. Remove the bulb from the headlight assembly by turning it counterclockwise. 5. Replace the bulb with new one. 6. Reconnect the electrical connector. At this time, use care not to touch the bulb surface. 7. To install assembly, turn it clockwise until it clicks. 8. (right-hand side) 9. Set

the washer tank to the original

the air intake duct with clip.

the bulb to the headlight

Install

Black plate (401,1)

Maintenance and service 11-53

place and secure it by clip. (left-hand side)

& Parking light It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if necessary.

& Front turn signal light It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if necessary.

& Front fog light (if equipped) It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if necessary.

11

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

11-54 Maintenance and service

& Rear combination lights

! Sedan

1. Push the knobs of the cover to open the cover.

Black plate (402,1)

! Station wagon

1) Rear turn signal light 2) Backup light 3) Brake/tail and rear side marker light

2. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise. 3. Pull the bulb out of the bulb holder and replace it with a new one. 4. Set into the rear the bulb holder combination light assembly and turn it clockwise until it locks. 5. Securely lock the cover against the trunk trim by using the screwdriver to turn the top knob clockwise.

1. Using a Phillips screwdriver, remove the upper and lower screws.

2. Wrap tape around a flat-head screw- driver, then insert the screwdriver into the gap A between the side cover and rear

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

combination lamp and use it as a lever to undo the clip. Undo clips C and D in the same way, then remove the side cover.

Black plate (403,1)

Maintenance and service 11-55

& Backup light (Station wagon)

3. Remove the upper and lower screws. Then, slide the rear combination lamp assembly to the rear and remove it from the vehicle.

1) Brake/tail light 2) Rear turn signal light 3) Rear side marker light

4. Remove the bulb holder from the rear combination light assembly by turning it counterclockwise. 5. Pull the bulb out of the bulb holder and replace it with a new one. 6. Set into the rear the bulb holder combination light assembly and turn it clockwise until it locks. 7. Close the cover and latch the lock. 8. Reinstall assembly and its side cover.

the rear combination light

1. Use a flat-head screwdriver to remove the light cover from the top of the left-hand rear gate trim.

11

2. Turn the bulb socket counterclockwise

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

11-56 Maintenance and service

and remove it.

! Station wagon

Black plate (404,1)

new bulb. 4. Reinstall the lens and cover. 5. Tighten the mounting screws.

& Dome light

3. Pull the bulb out of the bulb socket and replace it with a new one. 4. Install clockwise. rear gate.

the bulb socket by turning it Install the light cover on the

& License plate light

! Sedan It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if necessary.

1. Remove the mounting screws using a Phillips screwdriver. 2. Remove the lens.

1. Remove the lens by prying the edge of the lens with a flat-head screwdriver.

3. Pull the bulb out of the socket. Install a

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

& Map light

Black plate (405,1)

Maintenance and service 11-57

straight downward to remove it. 3. Install a new bulb. 4. Reinstall the lens.

& Door step light

2. Turn the bulb until the flat surfaces at its ends are aligned vertically. Pull the bulb straight downward to remove it. Install a new bulb. 3. Reinstall the lens.

1. Remove the lens by prying the edge of the lens with a flat-head screwdriver.

1. Remove the lens by prying the edge of the lens with a flat-head screwdriver.

11

2. Turn the bulb until the flat surfaces at its ends are aligned vertically. Pull the bulb

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Black plate (406,1)

11-58 Maintenance and service

& Cargo area light (Station wa-

gon)

2. Pull the bulb out of the socket. Install a new bulb. 3. Reinstall the lens.

1. Remove the cargo area light assembly by prying the edge of the light with a flat- head screwdriver. 2. Remove the lens from the cargo area light assembly.

3. Pull the bulb out of the socket. Install a new bulb. 4. Reinstall the lens.

& Trunk light (Sedan)

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

1. Remove the cover by pulling it out. 2. Pull the bulb out of the socket. Install a new bulb. 3. Reinstall the cover.

& High mount stop light (Se-

dan)

It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if necessary.

Black plate (407,1)

Maintenance and service 11-59

11

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Black plate (2,1)

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Left Page

Model "ALL_MODEL_MEMO" EDITED: 2006/ 1/ 17

Black plate (23,1)

Specifications

Specifications ..................................................... 12-2
Dimensions........................................................ 12-2
Engine ............................................................... 12-3
Electrical system................................................ 12-3
Capacities .......................................................... 12-4
Tires .................................................................. 12-5
Wheel alignment ................................................ 12-5

Fuses and circuits .............................................

12-6

Fuse panel located in the passenger

compartment ...................................................

Fuse panel located in the engine

compartment ................................................... Bulb chart........................................................... Vehicle identification .......................................

12-6

12-8
12-9
12-11

12

北米Model "A2420BE-B" EDITED: 2006/ 7/ 31

Black plate (410,1)

12-2 Specifications

Specifications

These specifications are subject to change without notice. & Dimensions

Item

Legacy

OUTBACK

Sedan

Station wagon

Sedan

Station wagon

in (mm)

Non- turbo

Turbo

2.5-liter

2.5-liter

3.0-liter

2.5-liter

3.0-liter

Except 2.5GT spec.B

2.5GT spec.B

186.2 (4,730)

68.1 (1,730)

56.1

(1,425)

56.5

(1,435)

105.1 (2,670)

58.9 (1,495)

58.5 (1,485)

Overall length

Overall width

Overall height

Wheel base

Tread

Front

Rear

Ground clearance

188.8 (4,795)

68.1 (1,730)

186.2 (4,730)

69.7 (1,770)

58.1 (1,475)

59.6 (1,515)

105.1 (2,670)

58.9 (1,495)

58.5 (1,485)

105.1 (2,670)

58.9 (1,495)

58.7 (1,490)

8.5 (215)

5.9
(150)

6.3
(160)

5.9
(150)

6.1
(155)

Non- turbo

Turbo

188.8 (4,795)

69.7 (1,770)

63.2 (1,605)

105.1 (2,670)

58.9 (1,495)

58.7 (1,490)

8.5
(215)

8.7
(220)

8.5 (215)

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Black plate (411,1)

Specifications 12-3

& Engine

Engine model

Engine type

Displacement cu-in (cc) Bore 6 Stroke in (mm) Compression ratio

Firing order

& Electrical system

EJ253

(2.5-liter, SOHC, non-turbo)

EJ255

(2.5-liter, DOHC, turbo)

EZ30D

(3.0-liter, DOHC, non-turbo)

Horizontally opposed, liquid cooled 4 cylinder,

4 stroke gasoline engine

Horizontally opposed, liquid cooled 6 cylinder,

4 stroke gasoline engine

150 (2,457)

3.92 6 3.11 (99.5 6 79.0)

10.0 : 1

8.4 : 1

1 – 3 – 2 – 4

183 (3,000)

3.51 6 3.15 (89.2 6 80.0)

10.7 : 1

1 – 6 – 3 – 2 – 5 – 4

Battery type and capacity (5HR)

2.5-liter models

MT

AT

Alternator

Spark plugs

3.0-liter models

2.5-liter non-turbo models

2.5-liter turbo models

3.0-liter models

55D23L (12V-48AH)

75D23L (12V-52AH)

75D23L (12V-52AH)

12V-110A

FR5AP-11 (NGK) SILFR6A (NGK)

ILFR6B (NGK)

12

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

12-4 Specifications

& Capacities

Fuel tank Engine oil

Transmission oil (MT)

2.5-liter models

3.0-liter models

5-speeds

6-speeds

Transmission fluid (AT)

2.5-liter non-turbo models

2.5-liter turbo and 3.0-liter models

AT differential gear oil

2.5-liter non-turbo models

Rear differential gear oil

Turbo 6-speeds MT models

2.5-liter turbo and 3.0-liter models

Power steering fluid Engine coolant

Other models

2.5-liter non-turbo models MT AT

2.5-liter turbo models

3.0-liter models

MT

AT

Black plate (412,1)

16.9 US gal (64 liters, 14.1 Imp gal)

4.2 US qt (4.0 liters, 3.5 Imp qt)

5.8 US qt (5.5 liters, 4.8 Imp qt)

3.7 US qt (3.5 liters, 3.1 Imp qt)

4.3 US qt (4.1 liters, 3.6 Imp qt)

9.8 US qt (9.3 liters, 8.2 Imp qt)

10.4 US qt (9.8 liters, 8.6 Imp qt)

1.3 US qt (1.2 liters, 1.1 Imp qt)

1.5 US qt (1.4 liters, 1.2 Imp qt)

1.0 US qt (1.1 liter, 0.9 Imp qt)

0.8 US qt (0.8 liter, 0.7 Imp qt)

0.7 US qt (0.7 liter, 0.6 Imp qt)

6.8 US qt (6.4 liters, 5.6 Imp qt)

6.7 US qt (6.3 liters, 5.5 Imp qt)

7.7 US qt (7.3 liters, 6.4 Imp qt)

7.6 US qt (7.2 liters, 6.3 Imp qt) 7.6 US qt (7.2 liters, 6.3 Imp qt)

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Black plate (413,1)

Specifications 12-5

& Tires

Tire size

Wheel size Pressure

Temporary spare tire

P205/55R16 89H P225/60R16 97H P205/50R17 88V

16 6 6.5JJ

215/45ZR17
17 6 7 JJ

P225/55R17 95V

215/45R18 89Y

18 6 7 JJ

32 psi (220 kPa,

2.2 kgf/cm2)

32 psi (220 kPa,

2.2 kgf/cm2)

33 psi (230 kPa,

2.3 kgf/cm2)

35 psi (240 kPa,

2.4 kgf/cm2)

32 psi (220 kPa,

2.2 kgf/cm2)

33 psi (230 kPa,

2.3 kgf/cm2)

30 psi (210 kPa,

2.1 kgf/cm2)

30 psi (210 kPa,

2.1 kgf/cm2)

32 psi (220 kPa,

2.2 kgf/cm2)

33 psi (230 kPa,

2.3 kgf/cm2)

30 psi (210 kPa,

2.1 kgf/cm2)

32 psi (220 kPa,

2.2 kgf/cm2)

–

32 psi (220 kPa,

2.2 kgf/cm2)

T135/80R16

T155/70D17

–

T135/80R16
T135/70D17
60 psi (420 kPa, 4.2 kgf/cm2)

32 psi (220 kPa,

2.2 kgf/cm2)

–

T155/70D17

T155/70D17

Front

Rear

Rear at trailer towing

Size

Pressure

& Wheel alignment

Toe

Camber

Item

Front

Rear

Front

Rear

Legacy

OUTBACK

Sedan

Station wagon

Sedan

Station wagon

0 in (0 mm)

0 in (0 mm)

−0815’

−0840’

−0830’

0840’ −0810’

12

北米Model "A2420BE-B" EDITED: 2006/ 7/ 28

Black plate (414,1)

12-6 Specifications

Fuses and circuits & Fuse panel located in the passenger compartment

Fuse panel

10

11

12

Fuse rating 20A

Empty

15A 15A

15A

7.5A

15A

20A

20A

7.5A

7.5A

15A

Circuit

. Cargo fan

Trailer hitch connector

rear

view mirrors

Integrated unit

Front wiper deicer relay

. Door locking . Moonroof . Combination meter . Remote control . Seat heater relay . Vanity mirror light . Combination meter . Stop light . Mirror heater . Power supply (Battery) . Clock . Automatic transmission . SRS airbag . Engine control unit

Front wiper deicer

Turn signal unit

Integrated unit

system

(Sub)

unit

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Black plate (415,1)

Specifications 12-7

Circuit

Fog light

Front wiper Front wiper washer

. Blower fan . Auto air conditioner unit . Headlight left side relay . ABS/Vehicle dynamics

Integrated unit

control unit

Fuse panel

28

29

30

31

32

33

Fuse rating 15A

15A

30A

7.5A

7.5A

7.5A

Circuit

. Cargo socket . Position light . Rear combination light

Tail light

Illumination

. Seat heaters . Backup light . Headlight right side re-

lay

. Cigarette lighter socket . Starter relay . Air conditioner . Rear window defogger

relay coil

Fuse rating 20A

15A

Empty

10A

15A

10A

7.5A

10A

7.5A

15A

15A

15A

15A

Fuse panel

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

. Rear wiper . Rear window washer . Audio unit . Clock . SRS airbag

system

(Main)

7.5A

15A

. Power window relay . Blower fan

12

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

12-8 Specifications

& Fuse panel located in the engine compartment

A) FWD socket (AT vehicles – except Turbo models and 3.0-liter models) B) Main fuse

Fuse panel

10

11

12

13

14

15

16

Black plate (416,1)

Circuit

. ABS unit . Vehicle dynamics control

unit

. Main fan (3.0-liter mod-

els)

. Sub fan (Except 3.0-liter

models) . Main fan . Audio . Headlight (right side) . Headlight (left side) . Backup light . Horn . Rear window defogger Fuel pump . Automatic control unit

transmission

Fuse rating 30A

25A

25A

25A

20A

15A 15A

20A

15A

25A

15A

15A

7.5A . Engine control unit 15A

Turn and hazard warning flasher

. Parking switch

20A 7.5A . Alternator

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Bulb chart

Description Headlight

Low beam High beam Front fog light

Except OUTBACK OUTBACK

Front turn signal/parking and front side marker Rear combination light

Rear turn signal light (Se- dan) Brake/tail and rear side marker (Sedan) Brake/tail (Station wagon) Rear side marker (Station wagon) Rear turn signal light (Station wagon) Backup light

High mount stop light (Sedan) License plate light

Wattage

12V-55W 12V-60W

12V-55W 12V-51W 12V-27/8W

12V-21W

12V-21/5W

12V-21/5W

12V-5W

12V-21W

12V-16W 12V-21W 12V-5W

Bulb No.

H7
9005 (HB3)

H3
9006 (HB4) 3157A

(W21W)

(W21/5W)

(W21/5W)

168

(W21W)

921
(W21W) 168

Black plate (417,1)

Specifications 12-9

12

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Black plate (418,1)

12-10 Specifications

Description Trunk room light Cargo area light Dome light Map light Door step light

Wattage 12V-5W 12V-13W 12V-8W 12V-8W 12V-3.5W

Bulb No. W5W –

–

–

–

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Vehicle identification

Black plate (419,1)

Specifications 12-11

1) Emission control label 2) Vehicle identification number 3) Certification and bar code label 4) 5) Vehicle identification number plate 6) Model number label 7)

Tire inflation pressure label

Fuel label

12

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Black plate (2,1)

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Left Page

Model "ALL_MODEL_MEMO" EDITED: 2006/ 1/ 17

Black plate (25,1)

Consumer information and Reporting safety defects

For U.S.A. ........................................................... 13-2
Tire information.................................................. 13-2
Tire labeling ....................................................... 13-2
Recommended tire inflation pressure.................. 13-5
Glossary of tire terminology ............................... 13-6
Tire care – maintenance and safety practices.......................................................... 13-7
Vehicle load limit – how to determine.................. 13-8

Determining compatibility of tire and vehicle load

capacities ...................................................... Adverse safety consequences of overloading on handling and stopping and on tires ................ Steps for Determining Correct Load Limit......... Uniform tire quality grading standards .......... Treadwear ....................................................... Traction AA, A, B, C......................................... Temperature A, B, C......................................... Reporting safety defects (USA) ......................

13-10

13-11
13-11
13-12
13-12
13-12
13-12
13-13

13

北米Model "A2420BE-B" EDITED: 2006/ 7/ 31

13-2 Consumer information and Reporting safety defects

For U.S.A.

The following information has been compiled according to Code of Fed- eral Regulations “Title 49, Part 575”.

Tire information & Tire labeling Many markings (e.g. Tire size, Tire Identification Number or TIN) are placed on the sidewall of a tire by tire manufacturers. These marking can provide you with useful information on the tire. ! Tire size Your vehicle comes equipped with P- Metric tire size. to understand the sizing system in se- lecting the proper tire for your vehi- cles. Here is a brief review of the tire sizing system with a breakdown of its individual elements. ! P Metric With the P-Metric system, Section Width is measured in millimeters. To convert millimeters into inches, divide by 25.4. The Aspect Ratio (Section Height divided by Section Width) helps provide more dimensional in- formation about the tire size.

is important

It

Black plate (422,1)

Example:

(1) P = Certain tire type used on light duty vehicles such as passenger cars (2) Section Width in millimeters (3) Aspect Ratio (= section height 7
section width). (4) R = Radial Construction (5) Rim diameter in inches (6) ZR = Speed category above 149
mph (240 km/h) ! Load and Speed Rating Descrip-

tions

The load and speed rating descrip- tions will appear following the size designation. facts They provide two important about the number designation is its load index. Second, the letter designation indicates the tire’s speed rating.

the tire. First,

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Black plate (423,1)

Consumer information and Reporting safety defects 13-3

Example:

(6) Load Index: A numerical code which specifies the maximum load a tire can carry at the speed indicated by its speed symbol, at maximum inflation pressure. For example, “88” means 1,234 lbs (560 kg), “87” means 1,201 lbs (545
kg), “86” means 1,168 lbs (530 kg)

WARNING

Load indices apply only to the tire, not to the vehicle. Putting a load rated tire on any vehicle does not mean the vehicle can be loaded up to the tire’s rated load.

(7) Speed Rating: An alphabetical system describing a tire’s capability to travel at established and predeter- mined speeds. For example, “V” means 149 mph (240 km/h)

WARNING

. Speed ratings apply only to the tire, not to the vehicle. Putting a speed rated tire on any vehicle does not mean the vehicle can be operated at the tire’s rated speed.

. The speed rating is void if the tires are worn out, damaged, repaired, retreaded, or other- wise altered from their origi- nal condition. tires are repaired, retreaded, or other- wise altered, they may not be suitable for original equip- ment tire designed loads and speeds.

If

! Tire Identification Number (TIN) Tire Identification Number is marked on the intended outboard sidewall. The TIN is composed of four groups. Here is a brief review of the TIN with a breakdown of its individual elements.

(TIN)

(1) Manufacturer’s Identification Mark (2) Tire Size (3) Tire Type Code (4) Date of Manufacture The first two figures identify the week, starting with “01” to represent the first full week of the calendar year; the second two figures represent the year. For example, 0101 means the 1st week of 2001. ! Other markings The following makings are also placed on the sidewall. ! Maximum permissible inflation

pressure

The maximum cold inflation pressure to which this tire may be inflated. For example, “300 kpa (44 PSI) MAX. PRESS” ! Maximum load rating The load rating at the maximum permissible weight load for this tire. For example, “MAX. LOAD 730 kg (1609 LBS) @ 300 kpa (44 PSI) MAX. PRESS.”

– CONTINUED –

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

13

Black plate (424,1)

13-4 Consumer information and Reporting safety defects

WARNING

Maximum load rating applies only to the tire, not to the vehicle. Putting a load rated tire on any vehicle does not mean the vehicle can be loaded up to the tire’s rated load.

“TUBELESS STEEL

! Construction type Applicable construction of this tire. For example, BELTED RADIAL” ! Construction The generic name of each cord material used in the plies (both side- wall and tread area) of this tire. “PLIES: TREAD 2
For example, STEEL + 2 POLYESTER + 1 NYLON SIDEWALL 2 POLYESTER” ! Uniform Tire Quality Grading

(UTQG) For details, quality grading standards” chapter.

refer

to “Uniform tire in this

北米Model "A2420BE-B" EDITED: 2006/ 7/ 26

Black plate (425,1)

Consumer information and Reporting safety defects 13-5

& Recommended tire inflation pressure ! Recommended cold tire inflation pressure Recommended cold tire inflation pressure for your vehicle’s tires is as follows,

Tire size

Wheel size Pressure