2000 Subaru Legacy Owners Manual

B Eject button ( When the “ tape is ejected. Before the ignition switch is turned to the “OFF” position, eject the tape from the player. Always make certain that you remove the cas- sette tape.

B Dolby BNR button (BNR) Press “BNR” button Q when playing tapes recorded using the Dolby NR system*. The “BNR” indicator will light up and high-frequency noise on the tape will be reduced for clearer sound reproduction.

* Noise reduction system manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D Symbol are trade marks of Dolby Laboratories Licensing Corporation.

5-38

Legacy U.S.A. (66L) A2260BE–B

CD player operation (if optional CD player is connected) An optional CD player can be connected to this audio unit. See your SUBARU dealer for more information. For CD player operation proce- dures, refer to “CD player 2” in this chapter.

Audio

CD player 1 (if equipped)

1 Disc slot 2 Disc indicator

3 Eject button

HB5039BB

– CONTINUED –

5-39

Legacy U.S.A. (66L) A2260BE–B

CAUTION

D Use only music CDs identified by D Do not use CDs listed below which could cause damage to the CD player.

mark.

D Any disc with a peel-off or seal on it. D Any disc with scratches and/or dust. D Bent disc. D Cleaning disc. D CD accessory. (E.g., 3-inch (8 cm) disc adapter)

D Do not insert or remove any disc when the automatic transmis- sion selector lever is in the park position; the selector lever in that position can interfere with disc insertion or removal, causing scratches on the disc surface (for AT vehicles).

B To insert a disc Be sure to hold a disc with the label side (the side where titles are printed) up. Push the disc into the slot. The disc will be automatically set in position by the auto-loading mechanism and begin playing. The disc indicator will turn on as the CD begins playing.

n Disc indicator Lit: A disc is in the slot (When the ignition switch is in the “ON” or “ACC” position). OFF: No disc is loaded or the ignition switch is in the “Lock” position.

B To remove disc left in slot Simply press the “Eject button” 3 and the disc will be ejected. This procedures is effective even when the ignition switch is in the “LOCK” position.

n Function control Refer to CD player control operating instructions described in the “Type P119 and P120 audio sets” section.

5-40

Legacy U.S.A. (66L) A2260BE–B

CD player 2 (if equipped)

Compact disc player operation

Audio

HB5044BB

1 Eject button 2 Repeat/random button 3 Scan/top button 4 Disc slot

5 Fast forward and track up

button

6 Play/pause button 7 Fast reverse and track down

button

B To playback a compact disc n When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position. A 8 cm/3 inch CD may also be used without any adapter.

NOTE D DO NOT INSERT TWO DISCS INTO THE DISC INSERTION SLOT AT A TIME. D Be sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the player might shut off. D After the last song finishes, the player will automatically return to track 1 (the first song on the disc).

– CONTINUED –

5-41

Legacy U.S.A. (66L) A2260BE–B

n When CD is in the player When the “"/❚

” button 6 is pressed, the player will start playback.

NOTE After the last song finishes, the player will automatically return to track 1 (the first song on the disc).

B To stop playback of a CD When the “"/❚ ” button 6 is pressed during playback of a CD, the CD stops playing temporarily. To let the CD resume playing, press the button again.

B To select a song from its beginning n Forward direction Briefly press the “""❚ ” button 5 to skip to the beginning of the next track. Each time the button is pressed, the indicated track number will increase.

n Backward direction Briefly press the “❚ AA” button 7 to skip to the beginning of the cur- rent track. Each time the button is pressed, the indicated truck num- ber will decrease.

B Fast forwarding and fast reverse n Fast forward Press the “""❚ ” button 5 continuously for more than 0.5 second to fast forward the disc. Release the button to stop fast forwarding.

n Fast reverse Press the “❚ AA” button 7 continuously for more than 0.5 second to fast reverse the disc. Release the button to stop fast reverse.

B Repeat playback Use this to play a certain track repeatedly. During playback, press the “RPT/RDM” button 2 and release it in less than 2 seconds. The “RPT” indicator will come on and the song will be played continuously. To

5-42

❚ ❚ Legacy U.S.A. (66L) A2260BE–B

Audio

cancel the repeat mode, press the button again. Then the “RPT” indi- cator goes out, and normal playback mode is restored.

B Random playback Use this to play the tracks on the disc in random order. During play- back, press the “RPT/RDM” button 2 and hold it in for more than 2
seconds. The “RDM” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RDM” indicator goes out, and normal playback mode is restored.

B Scan Press the “SCN/TOP” button 3 and release it in less than 2 seconds, and you can hear the first 10 seconds of each track to seach for the desired program. To continue listening to the program, press the “SCAN” button again. After all tracks on the disc has been scanned, normal playback mode is restored.

B Top Use this to return to the first track on the disc during playback. Press the “SCN/TOP” button 3 and hold it in for more than 2 seconds. Play- back returns to the beginning of the first track on the disc.

B To eject a disc from the player When a disc is being played back or when a disc is in the player, press the eject button “ The disc may be removed even when the ignition switch is in the “LOCK” position.

”. The disc will be ejected.

NOTE D Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out. D To protect the disc, the disc is automatically loaded if it is left in the ejected position for more than approximately 15 seconds (Auto Reload). In this case, the disc is not played.

– CONTINUED –

5-43

Legacy U.S.A. (66L) A2260BE–B

In-dash 6 CD auto changer (if equipped)

1 Disc slot 2 Disc indicators (disc No.1 to 6)

3 Disc select buttons

(disc No.1 to 6)

4 Eject button

HB5040BB

CAUTION

D Do not attempt to insert two or more discs into the slot at a time. Doing so can cause mechanical damage to the CD changer. D Use only music CDs identified by a D Do not use CDs listed below which could cause damage to the CD player.

mark.

D 3-inch (8 cm) compact disc. D Any disc with a peel-off or seal on it. D Any disc with scratches and/or dust. D Bent disc. D Cleaning disc. D CD accessory. (E.g., 3-inch (8 cm) disc adapter)

D Do not insert or remove any disc when the automatic transmis- sion selector lever is in the park position; the selector lever in that position can interfere with disc insertion or removal, causing scratches on the disc surface (for AT vehicles).

5-44

Legacy U.S.A. (66L) A2260BE–B

Audio

B To insert a disc 1. Press one of the “Disc select” buttons 3 (numbered from 1 to 6) for which the disc indicator light 2 is “OFF”. The Disc indicator lights are located directly above the corresponding “Disc select” buttons. 2. The indicator will begin blinking. The blinking will last for 15 se- conds. During this period, insert a desired disc, and the disc will begin to play. (If any disc is not inserted during this period, the “Disc slot” 1
door will close. Repeat step 1.) Be sure to hold a disc with the label side (the side where titles are printed) up. 3. To insert another disc, repeat step 1 and 2 choosing a different disc select button.

B To insert six discs at a time 1. Press and hold the “Disc select” button number 1 until all disc indi- cators begin blinking (about 1.5 seconds). 2. The indicators will blink for 15 seconds. During this period, insert desired six discs. 3. When all discs are loaded, the first disc will begin to play. (If no disc is inserted within this 15 seconds, the entire disc load sequence will be canceled.)

B To remove a disc 1. Press the desired one of the “Disc select” buttons 3 (numbered from 1 to 6) for which the disc indicator light is on. 2. Press the “Eject button” 4. The selected disc will be ejected and the indicator light will begin blinking. 3. To remove another disc, repeat step 1 and 2 choosing a different “Disc select” button. (To remove discs when the ignition switch is in the “Lock” position, press the “Eject” button, and the first disc will be ejected. Press the “Eject” button again, and the next disc will be ejected and so on. At this time, the “Disc select” buttons are disabled.)

– CONTINUED –

5-45

Legacy U.S.A. (66L) A2260BE–B

B To remove all discs at one time 1. Press and hold the “Eject” button 4 until all “Disc” indicators begin blinking (about 1.5 seconds), and the first disc will be ejected. 2. When the disc is removed, the next one will be ejected, and so on.

B To replace a playing disc with another Simply press the desired one of “Disc select” buttons 3 (numbered from 1 to 6) or press the “DISC UP” or “DISC DOWN” button on the radio unit to select the desired disc, and the disc will begin to play.

B Disc indicators Lit: when the corresponding storage tray is occupied by a disc. Blinking: Disc player is either in loading, eject or changing mode. OFF: No disc is loaded or the ignition switch is in the “LOCK” position.

B Function control Refer to CD player control operating instructions described in the “Type P119 and P120 audio sets” or “Type P121 audio set” section.

5-46

Legacy U.S.A. (66L) A2260BE–B

Audio

Precautions to observe when handling a compact disc (CD)

D To remove a disc from the case, press the center of the case and hold both edges of the disc. If the disc surface is touched directly, contamina- tion could cause poor tone quality. Do not touch the disc surface. D Use a clean disc whenever possible. If there are deposits, wipe the disc surface from the center outward with a dry, soft cloth. Be sure not to use a hard cloth, thinner, benzene, alcohol, etc. D Never use a badly damaged, deformed or cracked disc. Malfunctions or problems might result. D A disc is vulnerable to heat. Never keep it either in places exposed to direct sunlight, near heaters or in vehicles parked in the sun or hot days.

OM-4747

– CONTINUED –

5-47

Legacy U.S.A. (66L) A2260BE–B

Interior equipment

. . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Interior light Dome/Rear map reading light (if equipped) Spotlight (if equipped) Sun visors

Vanity mirror (if equipped)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage compartment

Glove compartment Center console Coin tray Overhead console (if equipped)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cup holder Cigarette lighter (if equipped) Ashtray Accessory power socket Convenience hook Floor mat (if equipped) Luggage cover (if equipped) Cargo anchorage eyelets (if equipped) Storage tray (if equipped)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-2
6-2
6-4
6-5
6-6
6-6
6-7
6-7
6-8
6-8
6-9
6-11
6-12
6-13
6-15
6-17
6-17
6-19
6-20

Legacy U.S.A. (66L) A2260BE–B

Interior light

Cargo area light

ON

OFF

DOOR

HS6003BC

HB0377

The interior light switch has three positions: ON: The light stays on continuously. DOOR: Dome light — The light comes on only when any door is opened. Cargo area light (if equipped) — The light comes on only when the rear gate is opened. OFF: The light stays off.

When leaving your vehicle, make sure the light is turned off to avoid bat- tery discharge.

Dome/Rear map reading light (if equipped)

CAUTION

D Do not use excessive force or sharp objects to activate the switches. D Do not spray cleaner directly on the dome light lens or the switches. D Remove the lens and use a damp cloth to clean the switch sur- faces.

6-2

Legacy U.S.A. (66L) A2260BE–B

Interior equipment

1 Map light 2 MAP light dimmer switch 3 Main dome light 4 MAP light ON/OFF switch

5 OFF switch 6 DOOR switch 7 ON switch

HB6012BB

B Dome light ON mode: Pressing the “ON” switch 7 will turn on main dome light. DOOR mode: Pressing the “DOOR” switch 6 will allow all three lights to fully illuminate when door is opened and then fade out once door is closed. OFF mode: Pressing the “OFF” switch 5 will prevent all lights from illuminating when the door is opened.

B Rear map reading light n Turn ON or OFF Press the “MAP ON/OFF” switch 4 once to turn on the map light at full intensity. Press a second time to turn it off.

n Map light dimming This area 2 will vary the intensity of the map light depending on which dimming zone area is pressed.

– CONTINUED –

6-3

Legacy U.S.A. (66L) A2260BE–B

NOTE D The switch color will change to indicate position setting. Green indicates current switch while the other switches will be Red. (Map light switches will be Yellow regardless of setting). D Switch indicator lights will shut off when not in use, but will come back on when any switches are touched. D The light assembly is equipped with a time delayed-off feature. The lights will remain on for a few seconds after all vehicle doors are closed. D If a map light is in use and the door is opened, the map light will maintain its current setting even after the door is closed. D The light assembly is equipped with a 1 hour sleep mode timer that will turn off any light that may be accidentally left on. Touch- ing any switch will reactivate the unit and allow for continued op- eration.

Spotlight (if equipped)

HB2034CB

HB2006CB

6-4

Legacy U.S.A. (66L) A2260BE–B

Interior equipment

HB6006BB

To turn on the spotlight, push the switch. To turn it off, push the switch again.

When leaving the vehicle, make sure the light is turned off to avoid bat- tery discharge.

Sun visors

HB7001BA

To block out glare, swing down the visors. To use the sun visor at a side window, swing it down and move it sideways.

– CONTINUED –

6-5

Legacy U.S.A. (66L) A2260BE–B

J Vanity mirror (if equipped)

HB6017AA

To use the vanity mirror, swing down the sunvisor and open the vanity mirror cover.

B Vanity mirror with light (if equipped) The light beside the vanity mirror comes on when the ignition switch is either in the “ACC” or “ON” position and the mirror cover is opened.

Storage compartment

CAUTION

D Always keep the storage compartment closed while driving to reduce the risk of injury in the event of sudden stops or an acci- dent. D Do not store spray cans, containers with flammable or corro- sive liquids or any other dangerous items in the storage compart- ment.

6-6

Legacy U.S.A. (66L) A2260BE–B

J Glove compartment

Interior equipment

Lock

Unlock

HS0090

To open the glove compartment, pull the handle. To close it, push the lid firmly upward. To lock the glove compartment, insert the key and turn it clockwise.

J Center console

To open the lid, pull up the lock release.

HB6010BA

– CONTINUED –

6-7

Legacy U.S.A. (66L) A2260BE–B

J Coin tray

HS0096

To open the coin tray, pull the upper edge of the lid.

J Overhead console (if equipped)

CAUTION

When your vehicle is parked in the sun or a warm day, the inside of the overhead console heats up. Avoid storing plastic or other heat-vulnerable or flammable articles such as a lighter in the overhead console.

To open the console, push on the lid lightly and it will automatically open.

HB0269

6-8

Legacy U.S.A. (66L) A2260BE–B

Cup holder

Interior equipment

CAUTION

D When not in use, always keep the holder stored while driving to reduce the risk of injury in the event of a sudden stop or an accident. D Do not pick up a cup from the cup holder or put a cup in the holder while you are driving, as this may distract you and lead to an accident. D Take care to avoid spills. Beverages, if hot, might burn you or your passengers. Spilled beverages may also damage upholstery, carpets or audio equipment.

B Front cup holder n In instrument panel

HB7003BB

HB7004BA

The cup holder is located beside the climate control panel. To use the cup holder, push on the its front surface and it will automatically pop out. Then pull it out completely.

– CONTINUED –

6-9

Legacy U.S.A. (66L) A2260BE–B

n In center console

HB6009BA

The front passenger’s cup holder is built in the center console, beside the parking brake lever.

B Rear passenger’s cup holder (if equipped)

HB7009CA

HB7011AA

The rear passenger’s cup holder is located on the lower side of the back of the center console. To use the cup holder, open the lid by pulling its upper edge.

6-10

Legacy U.S.A. (66L) A2260BE–B

Interior equipment

Cigarette lighter (if equipped)

CAUTION

The electrical power socket located on the lower part of the instrument panel is designed to use only a SUBARU genuine cig- arette lighter plug. Do not use non-genuine cigarette lighter plugs or any “plug-in” type electrical accessories in the socket. Doing so may cause a short-circuit and overheating, resulting in a fire.

HB6011BA

The electrical power socket located on the lower part of the instrument panel can only be used as cigarette lighter socket. A cigarette lighter plug is an optional accessory. It is available from your SUBARU dealer. If smoking is not desired, always put the cap on the socket to prevent any foreign object from entering it.

B Cigarette lighter (if equipped)

WARNING

To avoid being burned, never grasp the lighter by the end with the heating element. Doing so could result in injury and could also damage the heating element.

CAUTION

Do not hold the lighter pushed in, because it will overheat.

– CONTINUED –

6-11

Legacy U.S.A. (66L) A2260BE–B

HB6011DA

The cigarette lighter operates only when the ignition switch is in the “ON” and “ACC” positions. To use the cigarette lighter, push in the knob and wait a few moments. It will automatically spring up when ready for use.

Ashtray

CAUTION

Do not use ashtrays as waste receptacles or leave a lighted ciga- rette in an ashtray. This could cause a fire.

Fully close the ashtray after using it to help reduce residual smoke.

HB6011CA

HB7009BA

6-12

Legacy U.S.A. (66L) A2260BE–B

Interior equipment

B Front ashtray To open the ashtray, pull the lid out. B Rear ashtray The rear ashtray is located on the upper side of the back of the center console. To open the ashtray, pull the upper edge of the lid.

To remove the ashtray for cleaning, open it and pull it out while pushing the inner plate down.

Accessory power socket

B In the luggage compartment (if equipped) and on the center

console (if equipped)

CAUTION

D Do not attempt to use a cigarette lighter in the accessory power socket. D Do not place any foreign objects, especially metal ones such as coins or aluminum foil, into the accessory power socket. That could cause a short circuit. Always put the cap on the accessory power socket when they are not in use. D Use only electrical appliances which are designed for 12V DC and which consume less than 120W. Overloading the accessory power socket can cause a short circuit. Do not use double adapt- ers or more than one electrical appliance. D If the plug on your electric appliance is either too loose or too tight for the accessory power socket, this can result in a poor contact or cause the plug to get stuck. Only use plugs that fit properly. D Use of an electric appliance in the accessory power socket for a long period of time while the engine is not running can cause battery discharge. D Before driving your vehicle, make sure that the plug and the cord on your electrical appliance will not interfere with your shift- ing gears and operating the accelerator and brake pedals. If they do, do not use the electrical appliance while driving.

– CONTINUED –

6-13

Legacy U.S.A. (66L) A2260BE–B

HB6018BA

HB7008BA

Electrical power (12V DC) from the battery is on tap at the socket when the ignition switch is either in the “ACC” or “ON” position. You can use an in-car use electrical appliance by connecting it to the socket.

B Electrical power socket located on the lower part of the instru-

ment panel

CAUTION

The electrical power socket located on the lower part of the instrument panel is designed to use only a SUBARU genuine cig- arette lighter plug. Do not use non-genuine cigarette lighter plugs or any “plug-in” type electrical accessories in the socket. Doing so may cause a short-circuit and overheating, resulting in a fire. Refer to the “Cigarette lighter” section in this chapter.

6-14

Legacy U.S.A. (66L) A2260BE–B

Convenience hook

B Coat hook

Interior equipment

CAUTION

Never hang anything on the coat hook that might obstruct the driver’s view or that could cause injury in sudden stops or in a collision. And do not hang items on the coat hook that weigh 2.2
lb (1 kg) or more.

HB7012BA

The coat hook is attached to each rear passenger’s hand grip.

B Shopping bag hook

CAUTION

Do not hang items on the shopping bag hook that weigh 2.2 lb (1
kg) or more.

– CONTINUED –

6-15

Legacy U.S.A. (66L) A2260BE–B

Sedan

HBF014CB

HB7014BD

n For sedan models A shopping bag hook is attached to each inner side wall of the trunk near the trunk lid opening.

n For station wagon models A shopping bag hook is attached to each side of the cargo area. To use the hook, push the upper portion and the shopping bag hook will appear.

6-16

Legacy U.S.A. (66L) A2260BE–B

Floor mat (if equipped)

Interior equipment

CAUTION

Make sure the driver’s floor mat is placed back in its proper loca- tion and correctly secured on its retaining pin. If the floor mat slips forward and interferes with the movement of the pedals dur- ing driving, it could cause an accident.

HB6015BA

HB6016BA

A retaining pin is located on the drivers side of the vehicle next to the fuel filler door release. The floor mat is secured using the built-in grom- met, by placing the grommet over the pin and pushing downward.

Luggage cover (if equipped)

WARNING

Do not place anything on the extended cover. Putting excessive weight on the extended cover can break it and an object on the cover could tumble forward in the event of a sudden stop or colli- sion. This could cause serious injury.

The luggage cover is provided for covering the cargo area and to pro- tect its contents from direct sunlight. This cover is detachable to make room for additional cargo.

– CONTINUED –

6-17

Legacy U.S.A. (66L) A2260BE–B

B Using the cover

HB7015BA

To extend the cover, pull the end of the cover out of the housing, then insert its hooks into the catches as shown. To rewind it, unhook it from the catches and it will rewind automatically. You should hold on to the cover and guide it back into the cover housing while it is rewinding.

B To remove the cover

HB7016BA

HB7017BA

1. Rewind the cover. 2. To take it off the cover rails, lift it out while pressing the release knobs located both sides of the cover housing. 3. Store the cover in the cargo area.

6-18

Legacy U.S.A. (66L) A2260BE–B

Interior equipment

To install the cover: Hang the both ends of the cover housing on the cover rails. Make sure that the cover is mounted securely by pulling it up.

Cargo anchorage eyelets (if equipped)

CAUTION

The cargo anchorage eyelets are designed only for securing light cargo. Never try to secure cargo that exceeds the capacity of the hooks. The maximum load capacity is 44 lb (20 kg) per eyelet.

HB7018BA

The cargo area is equipped with four anchorage eyelets so that cargo can be secured with a luggage net or ropes.

When using the anchorage eyelets, turn them down out of the storing recesses. When not in use, put the eyelets up into the storing recesses.

– CONTINUED –

6-19

Legacy U.S.A. (66L) A2260BE–B

Storage tray (if equipped)

CAUTION

D Always keep the lid of the storage tray closed while driving to reduce the risk of injury in the event of sudden stop or an acci- dent. D Do not store spray cans, containers with flammable or corro- sive liquids or any other dangerous items in the storage tray.

Sedan

HB6007BB

HB7019AD

HB6008BA

The storage tray is located under the floor of the trunk or cargo area and can be used to store small items. To open the lid, pull the tab or handle up.

6-20

Legacy U.S.A. (66L) A2260BE–B

Interior equipment

Station wagon: Hang the hook provided on the underside of the lid on the rear edge of the roof to keep the lid open.

NOTE When storing a flat tire, put the storage tray in the trunk or cargo area.

– CONTINUED –

6-21

Legacy U.S.A. (66L) A2260BE–B

Starting and operating

Fuel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel requirements Fuel filler lid and cap

State emission testing (U.S. only) Preparing to drive Starting the engine

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Starting the engine for a manual transmission vehicle Starting the engine for an automatic transmission vehicle Starting the engine during cold weather below –4°F (–20°C) Starting a flooded engine

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Stopping the engine Manual transmission Automatic transmission

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power steering Braking

Selector lever for automatic transmission Shift lock release

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Rear viscous limited slip differential (LSD)

(GT, GT-LTD, OUTBACK-CW and OUTBACK-LTD)

. . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Braking tips Brake system Disc brake pad wear warning indicators

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ABS (Anti-lock Brake System) Parking your vehicle Cruise control (if equipped)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7-2
7-2
7-4
7-6
7-7
7-8
7-8
7-9
7-10
7-10
7-10
7-11
7-14
7-15
7-19

7-20
7-20
7-21
7-21
7-21
7-22
7-23
7-25
7-27

Legacy U.S.A. (66L) A2260BE–B

Fuel

CAUTION

Use of a fuel which is low in quality or use of an inappropriate fuel additive may cause engine damage.

J Fuel requirements B Fuel Octane Rating Your engine is designed to use only unleaded gasoline with an octane rating of 87 AKI or higher. This octane rating is the average of the Re- search Octane and Motor Octane numbers and is commonly referred to as the Anti Knock Index (AKI).

Using a gasoline with a lower octane rating can cause persistent and heavy knocking, which can damage the engine. Do not be concerned if your vehicle sometimes knocks lightly when you drive up a hill or when you accelerate. See your dealer or a qualified service techni- cian if you use a gasoline with the specified octane rating and your vehicle knocks heavily or persistently.

B Unleaded gasoline The neck of the fuel filler pipe is designed to accept only an unleaded gasoline filler nozzle. Under no circumstances should leaded gaso- line be used because it will damage the emission control system and may impair driveability and fuel economy.

B Gasoline for California-certified LEV If your vehicle is a California-certified Low Emission Vehicle (LEV) as indicated on the underhood tune-up label, it is designed to optimize engine and emission control system performance with gasoline that meets California low sulfer specifications. Your vehicle will operate on gasoline meeting Federal specifications.

7-2

Legacy U.S.A. (66L) A2260BE–B

Starting and operating

B Gasoline for cleaner air

CAUTION

Do not let fuel spill on the exterior surfaces of the vehicle. Fuels containing alcohol may cause paint damage, which is not cov- ered under the SUBARU Limited Warranty.

Your use of gasoline with detergent additives will help prevent depos- its from forming in your engine and fuel system. This helps keep your engine in tune and your emission control system working properly, and is a way of doing your part for cleaner air. If you continuously use a high quality fuel with the proper detergent and other additives, you should never need to add any fuel system cleaning agents to your fuel tank.

Many gasolines are now blended with materials called oxygenates. Use of these fuels can also help keep the air cleaner. SUBARU ap- proves the use of oxygenated blend fuels, such as MTBE (Methyl Ter- tiary Butyl Ether) or ethanol (ethyl or grain alcohol). The blended fuels should contain no more than 15% MTBE or 10% ethanol for the proper operation of your SUBARU.

In addition, some gasoline suppliers are now producing reformulated gasolines, which are designed to reduce vehicle emissions. SUBARU approves the use of reformulated gasoline.

If you are not sure what the fuel contains, you should ask your service station operators if their gasolines contain detergents and oxygenates and if they have been reformulated to reduce vehicle emissions.

As additional guidance, only use fuels suited for your vehicle as ex- plained below.

D Fuel should be unleaded and have an octane rating no lower than that specified in this manual. D Methanol (methyl or wood alcohol) is sometimes mixed with un- leaded gasoline. Methanol can be used in your vehicle ONLY if it does not exceed 5% of the fuel mixture AND if it is accompanied by

– CONTINUED –

7-3

Legacy U.S.A. (66L) A2260BE–B

sufficient quantities of the proper cosolvents and corrosion inhibitors required to prevent damage to the fuel system. Do not use fuel con- taining methanol EXCEPT under these conditions. D If undesirable driveability problems are experienced and you sus- pect they may be fuel related, try a different brand of gasoline before seeking service at your SUBARU dealer. D Fuel system damage or driveability problems which result from the use of improper fuel are not covered under the SUBARU Limited War- ranty.

J Fuel filler lid and cap

B Refueling

WARNING

D Gasoline vapor is highly flammable. Before refueling, always first stop the engine and make sure that there are no lighted ciga- rettes, open flames or electrical sparks in the adjacent area. D When opening the cap, do not remove the cap quickly. Fuel may be under pressure and spray out of the fuel filler neck espe- cially in hot weather, which may cause injury.

CAUTION

D Never add any cleaning agents to the fuel tank. The addition of a cleaning agent may cause damage to the fuel system. D Make sure that the cap is tightened until it clicks to prevent fuel spillage in the event of an accident. D Do not let fuel spill on the exterior surfaces of the vehicle. Fuels may cause paint damage, which is not covered under the SUBARU Limited Warranty. D Always use a genuine SUBARU fuel filler cap. If you use the wrong cap, it may not fit or have proper venting, and your fuel tank and emission control system might be damaged.

7-4

Legacy U.S.A. (66L) A2260BE–B

Sedan

Starting and operating

HB3000BB

HBF013DA

HB3001BD

HB3007BA

1. To open the fuel filler lid, pull the lid release lever up.

2. Remove the fuel filler cap by turning it slowly counterclockwise.

HB3008BB

– CONTINUED –

7-5

Legacy U.S.A. (66L) A2260BE–B

3. Stop filling the tank after the fuel filler pump automatically clicks off. Do not add any more fuel. 4. Put the cap back on, turn it clockwise until you hear a clicking noise. Be certain not to catch the tether under the cap while tighten- ing. 5. Close the fuel filler lid completely. If you spill any fuel on the painted surface, rinse it off immediately. Otherwise, the painted surface could be damaged. NOTE If the fuel filler cap is not tightened until it clicks or if the tether is caught under the cap, the CHECK ENGINE warning light may come on. Refer to the “Warning and indicator lights” section lo- cated in chapter 3.

State emission testing (U.S. only)

WARNING

Testing of an All-Wheel Drive vehicle must NEVER be performed on a single two-wheel dynamometer. Attempting to do so will result in uncontrolled vehicle movement and may cause an acci- dent or injuries to persons nearby.

CAUTION

Resultant vehicle damage due to improper testing is not covered under the SUBARU Limited Warranty and is the responsibility of the state inspection program or its contractors or licensees.

At state inspection time, remember to tell your inspection or service station in advance not to place your Subaru AWD vehicle on a two- wheel dynamometer. Otherwise, serious transmission damage will result.

Some states have started using dynamometers in their state inspection programs in order to meet their obligation under federal law to implement

7-6

Legacy U.S.A. (66L) A2260BE–B

Starting and operating

stricter vehicle emission standards to reduce air pollution from cars. A dynamometer is a treadmill or roller-like testing device that allows your car’s wheels to turn while the car remains in one place. Depending on the severity of a state’s air pollution problems, the states must adopt either a “basic” or “enhanced” vehicle emission inspection test. Nor- mally, a portion of the basic emission test consists of an emission inspector inserting an analyzer probe into the exhaust pipe of an idling vehicle for a short period of time. States with more severe air pollution problems are required to adopt an enhanced vehicle emission test. This test simulates actual driving conditions on a dynamometer and permits more accurate measurement of tailpipe emitted pollution than the basic emission test. The U.S. Environmental Protection Agency (EPA) and states using two- wheel dynamometers testing programs have EXEMPTED Subaru AWD vehicles from the portion of the testing pro- gram that involves a two-wheel dynamometer.

their emission

in

There are some states that use four-wheel dynamometers in their testing programs. When properly used, that equipment will not damage an AWD Subaru vehicle.

77

Under no circumstances should the rear wheels be jacked off the ground, nor should the driveshaft be disconnected for state emission testing.

Preparing to drive

You should perform the following checks and adjustments every day be- fore you start driving.

1. Check that all windows, mirrors, and lights are clean and unob- structed. 2. Check the appearance and condition of the tires. Also check tires for proper inflation. 3. Look under the vehicle for any sign of leaks. 4. Check that the hood, trunk and rear gate are fully closed. 5. Check the adjustment of the seat. 6. Check the adjustment of the inside and outside mirrors.

– CONTINUED –

7-7

Legacy U.S.A. (66L) A2260BE–B

7. Fasten your seatbelt. Check that your passengers have fastened their seatbelts. 8. Check the operation of the warning and indicator lights when the igni- tion switch is turned to the “ON” position. 9. Check the gauges, indicator and warning lights after starting the en- gine.

NOTE Engine oil, engine coolant, brake fluid, washer fluid and other fluid levels should be checked daily, weekly or at fuel stops.

Starting the engine

CAUTION

Do not operate the starter motor continuously for more than ten seconds. If the engine fails to start after operating the starter for five to ten seconds, wait for ten seconds or more before trying again.

J Starting the engine for a manual transmission vehicle 1. Apply the parking brake. 2. Turn off unnecessary lights and accessories. 3. Press the clutch pedal to the floor and shift the shift lever into neutral. Hold the clutch pedal to the floor while starting the engine. The starter motor will only operate when the clutch pedal is pressed fully to the floor. 4. Turn the ignition switch to the “ON” position and check the operation of the warning and indicator lights. Refer to the “Warning and indicator light” section (chapter 3). 5. Turn the ignition switch to the “START” position without depressing the accelerator pedal. Release the key immediately after the engine has started.

If the engine does not start within ten seconds, wait a while and then turn the ignition switch to the “START” position again while depressing the ac- celerator pedal half way down.

7-8

Legacy U.S.A. (66L) A2260BE–B

Starting and operating

6. Confirm that all warning and indicator lights have gone off after the engine has started. The fuel injection system automatically lowers the idle speed as the engine warms up.

J Starting the engine for an automatic transmission ve-

hicle

CAUTION

If you restart the engine while the vehicle is moving, shift the se- lector lever into the “N” position. Do not attempt to place the se- lector lever of a moving vehicle into the “P” position.

1. Apply the parking brake. 2. Turn off unnecessary lights and accessories. 3. Shift the selector lever to the “P” or “N” position (preferably “P” posi- tion). The starter will only operate when the select lever is at the “P” or “N” position. 4. Turn the ignition switch to the “ON” position and check the operation of the warning and indicator lights. Refer to the “Warning and indicator lights” section (chapter 3). 5. Turn the ignition switch to the “START” position without depressing the accelerator pedal. Release the key immediately after the engine has started. If the engine does not start within ten seconds, wait a while and then turn the ignition switch to the “START” position again while depressing the ac- celerator pedal half way down. 6. Confirm that all warning and indicator lights have gone out after the engine has started. The fuel injection system automatically lowers the idle speed as the engine warms up.

While the engine is warming up, make sure that the selector lever is at the “P” or “N” position and that the parking brake is applied.

– CONTINUED –

7-9

Legacy U.S.A. (66L) A2260BE–B

J Starting the engine during cold weather below –4°F

(–20°C)

If the engine is difficult to start using the normal method (without de- pressing the accelerator pedal), turn the ignition switch to the “START” position while slightly depressing the accelerator pedal.

J Starting a flooded engine If the engine does not start, it may be flooded (excessive fuel in the en- gine). In case of a flooded engine, turn the starter motor for five seconds with the accelerator pedal fully depressed. Repeat this two or three times until the engine starts. Release the ignition switch and accelerator pedal as soon as the engine starts.

Stopping the engine

WARNING

Do not stop the engine when the vehicle is moving. This will cause loss of power to the power steering and the brake booster, making steering and braking more difficult. It could also result in accidental activation of the “LOCK” position on the ignition switch, causing the steering wheel to lock.

The ignition switch should be turned off only when the engine is idling.

7-10

Legacy U.S.A. (66L) A2260BE–B

Manual transmission

Starting and operating

WARNING

Do not drive the vehicle with the clutch disengaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutral position. Engine braking has no effect in either of these condi- tions and the risk of an accident is consequently increased.

CAUTION

Shift into reverse ONLY when the vehicle has completely stopped. It may cause damage to the transmission to try shifting into reverse when the vehicle is moving.

The manual transmission is a fully synchromeshed 5-forward and 1-re- verse speed transmission.

OM-H2241

The shift pattern is shown on the shift lever knob. When shifting from 5th gear to reverse gear, first return the shift lever to the neutral position then shift into reverse gear.

To change gears, fully depress the clutch pedal, move the shift lever, and gradually let up on the clutch pedal. If it is difficult to shift into gear, put the transmission in neutral, release the clutch pedal momentarily, and then try again.

– CONTINUED –

7-11

Legacy U.S.A. (66L) A2260BE–B

B Shifting speeds n Recommended shifting speeds The best compromise between fuel economy and vehicle perfor- mance during normal driving is ensured by shifting up at the speeds listed in the following table.

Shift up

1st to 2nd

2nd to 3rd

3rd to 4th

4th to 5th

mph (km/h)

15 (24)

25 (40)

40 (65)

45 (73)

n Maximum allowable speeds

WARNING

When shifting down a gear, ensure that the vehicle is not travel- ling at a speed exceeding the Maximum Allowable Speed for the gear which is about to be selected. Failure to observe this pre- caution can lead to engine over-revving and this in turn can result in engine damage. In addition, sudden application of engine brakes when the vehicle is travelling on a slippery surface can lead to wheel locking; as a consequence, control of the vehicle may be lost and the risk of an accident increased.

The following table shows the maximum speeds that are possible with each different gear.

Never exceed the speed limit below for each gear position except for brief acceleration in an emergency. The tachometer’s needle (if so equipped) will enter the red area if these speeds are exceeded. Fail- ure to obseve this precaution can lead to excessive engine wear and poor fuel economy.

7-12

Legacy U.S.A. (66L) A2260BE–B

Vehicle type

Brighton

30 (48)

50 (81)

30 (49)

51 (82)

Starting and operating

mph (km/h)

OUT- BACK

31 (50)

52 (84)

GT

29 (47)

49 (79)

71 (115)

73 (117)

70 (112)

74 (119)

Gear

1st

2nd

3rd

B Driving tips Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill on an upgrade. Either of those actions may cause clutch damage. Do not drive with your hand resting on the shift lever. This may cause wear on the transmission components.

When it is necessary to reduce vehicle speed due to slow traffic, turn- ing corners, or driving up steep hills, downshift to a lower gear before the engine starts to labor.

On steep downgrades, downshift the transmission to 4th, 3rd or 2nd gear as necessary; this helps to maintain a safe speed and to extend brake pad life. In this way, the engine provides a braking effect. Remember, if you “ride” (over use) the brakes while descending a hill, they may over- heat and not work properly.

– CONTINUED –

7-13

Legacy U.S.A. (66L) A2260BE–B

Automatic transmission

WARNING

Do not shift from the “P” or “N” position into the “D”, “3”, “2”, “1” or “R” position while depressing the accelerator pedal. This may cause the vehicle to jump forward or backward.

CAUTION

D Shift into the “P” or “R” position only after the vehicle is com- pletely stopped. Shifting while the vehicle is moving may cause damage to the transmission. D Do not race the engine for more than five seconds in any posi- tion except the “N” or “P” position when the brake is set or the tires are on blocks. This may cause the automatic transmission fluid to overheat. D Avoid shifting from one of the forward driving positions into the “R” position or vice versa until the vehicle has completely stopped. Such shifting may cause damage to the transmission.

The automatic transmission is electronically controlled with 4-forward speeds and 1-reverse speed.

NOTE Immediately after a disconnected battery is reconnected or ATF (au- tomatic transmission fluid) is replaced, you may feel that the auto- matic transmission operation is somewhat unusual. This results from erasure or invalidation of data the on-board com- puter has collected and stored in memory to allow the transmission to shift at the most appropriate times for the current condition of your vehicle. Optimized shifting will be restored as the vehicle con- tinues to be driven for a while.

7-14

Legacy U.S.A. (66L) A2260BE–B

J Selector lever for automatic transmission

Starting and operating

HB7010AA

HB7021BB

The selector lever has seven positions.

B P (Park) This position is for parking the vehicle and starting the engine. In this position, the transmission is mechanically locked to prevent the vehicle from rolling freely. When you park the vehicle, first set the parking brake fully, then shift into the “P” position. Do not hold the vehicle with only the transmis- sion. A shift interlock function is employed in the automatic transmission system to ensure safe starting of the vehicle. To shift the selector lever from the “P” to the any other position, you have to depress the brake pedal fully when the ignition switch is in the “ON” position. This prevents the vehicle from lurching when it is started. If the shift lever does not move from the “P” position with the brake pedal depressed, refer to the “Shift lock release” section in this chap- ter.

B R (Reverse) This position is for backing the vehicle.

To shift from the “N” to “R” position, first stop the vehicle completely then move the lever to the “R” position.

– CONTINUED –

7-15

Legacy U.S.A. (66L) A2260BE–B

B N (Neutral)

WARNING

Do not drive the vehicle with the selector lever in the “N” (neutral) position. Engine braking has no effect in this condition and the risk of an accident is consequently increased.

This position is for restarting a stalled engine. In this position the wheels and transmission are not locked. In this position, the transmission is neutral; the vehicle will roll freely, even on the slightest incline unless the parking brake or foot brake is on.

B D (Drive) This position is for normal driving. The transmission automatically shifts into a suitable gear from 1st to 4th according to the vehicle speed and the acceleration you require.

When more acceleration is required in this position, press the acceler- ator pedal fully to the floor and hold that position. The transmission will automatically downshift to 3rd, 2nd or 1st gear. When you release the pedal, the transmission will return to the original gear position.

n While climbing a grade When driving up a hill, undesired upshift to 4th gear is prevented from taking place when the accelerator is released. This minimizes the chance of subsequent downshifting to a lower gear when accelerat- ing again. This prevents repeated upshifting and downshifting result- ing in a smoother operation of the vehicle.

NOTE The transmission may downshift to 2nd or 1st gear, depending on the way the accelerator pedal is pressed to accelerate the vehicle again.

n While going down a hill When descending a steep hill, depressing the brake pedal will cause the transmission to downshift to 3rd gear, thus applying engine brak- ing. Reacceleration for a short time will cause the transmission to up-

7-16

Legacy U.S.A. (66L) A2260BE–B

Starting and operating

shift normally.

NOTE In some cases, depressing the brake pedal on a downhill grade does not result in an automatic downshift to 3rd gear. This can happen when the automatic transmission fluid temperature is very low, for example, during driving shortly after the vehicle has been parked for an extended period of time. When the ATF tem- perature has risen to a certain level, automatic downshift normal- ly takes place. In the meantime, downshift manually for engine braking as required. Also, downshifting when braking downhill will not occur at speeds above approximately 50 mph (80 km/h).

B 3 (Third) This position is for using engine braking when going down a hill or for climbing a grade. The transmission automatically shifts into a suitable gear from 1st to 3rd according to the vehicle speed and the acceleration you require.

When more acceleration is required in this position, press the acceler- ator pedal fully to the floor and hold that position. The transmission will automatically downshift to 2nd or 1st gear. When you release the pedal, the transmission will return to the original gear position.

B 2 (Second) This position is for using engine braking when going down a hill or for climbing a steep grade. In this position, the transmission holds in the 2nd gear. Use this position when starting off from a standstill on slippery road surfaces such as mud or snow. It will ensure greater traction.

B 1 (First) This position is for driving up or down very steep grades, or driving through mud or sand, or on slippery surfaces. In this position, the transmission holds in the 1st gear.

– CONTINUED –

7-17

Legacy U.S.A. (66L) A2260BE–B

B Maximum speeds

WARNING

When shifting down a gear, ensure that the vehicle is not travel- ling at a speed exceeding the Maximum Allowable Speed for the gear which is about to be selected. Failure to observe this pre- caution can lead to engine over-revving and this in turn can result in engine damage. In addition, sudden application of engine brakes when the vehicle is travelling on a slippery surface can lead to wheel locking; as a consequence, control of the vehicle may be lost and the risk of an accident increased.

The following tables show the maximum speeds that are possible with each different gear. The tachometer’s (if so equipped) needle will enter the red area if these speeds are exceeded.

When shifting down a gear, it is important to confirm that the current vehicle speed is not in excess of the Maximum Allowable Speed of the gear which is about to be selected. Exceeding the Maximum Allowable Speeds will result in over-revving of the engine. In addition a powerful engine brake will engage and control of the vehicle may be lost.

mph (km/h)

Vehicle type

Position

Brighton, L

GT

OUTBACK

33 (53)

64 (103)

102 (164)

27 (43)

57 (92)

97 (156)

29 (47)

62 (100)

104 (167)

NOTE D In order to prevent over-revving during acceleration of the vehicle, the transmission will automatically shift to the next high- est gear if the Maximum Allowable Speed for the current gear is exceeded.

7-18

Legacy U.S.A. (66L) A2260BE–B

Starting and operating

D Similarly, in order to prevent over-revving during deceleration of the vehicle, the transmission will remain in the current gear if the speed of the vehicle is in excess of the Maximum Allowable Speed for the gear to which the selector lever has been moved.

B Driving tips D Always apply the foot or parking brake when the vehicle is stopped in the “D”, “3”, “2”, “1” or “R” position. D Always set the parking brake when parking your vehicle. Do not hold the vehicle with only the transmission. D Do not keep the vehicle in a stationary position on an uphill grade by using the “D”, “3”, “2”, or “1” position. Use the brake instead.

J Shift lock release If the selector lever does not move from the “P” position with the brake pedal depressed and the ignition switch in the “ON” position, perform the following steps: To override the shift lock: 1. Set the parking brake and stop the engine. 2. Take out the screwdriver from the tool bag. 3. Remove the cover by prying on the edge with the regular screwdriver.

HB7010CA

HB7020BA

4. Insert the screwdriver into the hole. 5. Push down on the screwdriver and move the selector lever from the “P” to the “N” position. 6. Remove the screwdriver from the hole. Depress the brake pedal and

– CONTINUED –

7-19

Legacy U.S.A. (66L) A2260BE–B

start the engine. Take your vehicle to the nearest SUBARU dealer immediately to have the system repaired.

Rear viscous limited slip differential (LSD) (GT, GT-LTD, OUTBACK-CW and OUTBACK-LTD)

CAUTION

D Never start the engine while a tire on one side is jacked up, as the vehicle may move. D If one rear tire is spinning in mud, avoid continued spinning at high speed as this could adversely affect the LSD. D If a different size rear tire is temporarily used (as in an emer- gency), it will adversely affect the LSD. Always replace it with a regular size tire as soon as possible.

The LSD provides optimum distribution of power according to the differ- ence in revolutions between the right and left rear wheels that may be caused by certain driving conditions, thereby improving driving stability on snow-covered, muddy or other slippery roads.

Power steering

CAUTION

Do not hold the steering wheel at the fully locked position left or right for more than five seconds. This may damage the power steering pump.

The power steering system operates only when the engine is running. If you lose power steering assist because the engine stops or the system fails to function, you can steer but it will take much more effort.

7-20

Legacy U.S.A. (66L) A2260BE–B

Braking

J Braking tips

Starting and operating

WARNING

Never rest your foot on the brake pedal while driving. This can cause dangerous overheating of the brakes and needless wear on the brake pads and linings.

B When the brakes get wet When driving in rain or after washing the vehicle, the brakes may get wet. As a result, brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly depressing the brake pedal to heat up the brakes.

B Use of engine braking Remember to make use of engine braking in addition to foot braking. When descending a grade, if only the foot brake is used, the brakes may start working improperly because of brake fluid overheating, caused by overheated brake pads. To help prevent this, shift into a lower gear to get stronger engine braking.

B Braking when a tire is punctured Do not depress the brake pedal suddenly when a tire is punctured. This could cause a loss of control of the vehicle. Keep driving straight ahead while gradually reducing speed. Then slowly pull off the road to a safe place.

J Brake system

B Two separate circuits Your vehicle has two separate circuit brake systems. Each circuit works diagonally across the vehicle. If one circuit of the brake system should fail, the other half of the system still works. If one circuit fails, the brake pedal will go down much closer to the floor than usual and you will need to press it down much harder. And a much longer dis- tance will be needed to stop the vehicle.

– CONTINUED –

7-21

77

Legacy U.S.A. (66L) A2260BE–B

B Brake booster The brake booster uses engine manifold vacuum to assist braking force. Do not turn off the engine while driving because that will turn off the brake booster, resulting in poor braking power. The brakes will continue to work even when the brake booster com- pletely stops functioning. If this happens, however, you will have to push the pedal much harder than normal and the braking distance will increase.

J Disc brake pad wear warning indicators

OM-H0163

The disc brake pad wear warning indicators on the disc brakes give a warning noise when the brake pads are worn. If a squeaking or scraping noise is heard from the disc brakes while braking, immediately have your vehicle checked by your SUBARU deal- er.

7-22

Legacy U.S.A. (66L) A2260BE–B

ABS (Anti-lock Brake System)

Starting and operating

WARNING

Always use the utmost care in driving – overconfidence because you are driving with an ABS equipped vehicle could easily lead to a serious accident.

CAUTION

D The ABS system does not always decrease stopping distance. You should always maintain a safe following distance from other vehicles. D When driving on badly surfaced roads, gravel roads, icy road, or over deep newly fallen snow, stopping distances may be long- er for a vehicle with the ABS system than one without. When driv- ing under these conditions, therefore, reduce your speed and leave ample distance from other vehicles. D When you feel the ABS system operating, you should maintain constant brake pedal pressure. Do not pump the brake pedal since doing so may defeat the operation of the ABS system.

The ABS system prevents the lock-up of wheels which may occur during sudden braking or braking on slippery road surfaces. This helps prevent the loss of steering control and directional stability caused by wheel lock-up.

When the ABS system is operating, you may hear a chattering noise or feel a slight vibration in the brake pedal. This is normal when the ABS operates.

The ABS system will not operate when the vehicle speed is below approximately 6 mph (10 km/h).

B ABS system self-check You may feel a slight shock in the brake pedal and hear the operating sound of ABS from the engine compartment just after the vehicle is

– CONTINUED –

7-23

Legacy U.S.A. (66L) A2260BE–B

started. This is caused by an automatic functional test of the ABS sys- tem being carried out and does not indicate any abnormal condition.

B ABS warning light

HB4010GA

The ABS warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds. This is an indication that the ABS system is working properly. If the warning light behaves as follows, the ABS system may not be working properly.

D The warning light does not come on when the ignition switch is turned to the “ON” position. D The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8 mph (12 km/h). D The warning light comes on during driving.

When the warning light is on, the ABS function shuts down; however, the conventional brake system continues to operate normally. If this occurs, have the ABS system repaired at the first available opportuni- ty by your SUBARU dealer.

NOTE If the warning light behavior is as described below, the ABS sys- tem may be considered normal. D The warning light comes on right after the engine is started

7-24

Legacy U.S.A. (66L) A2260BE–B

Starting and operating

but goes out immediately, remaining off. D The warning light remains on after the engine has been started, but it goes out when the vehicle speed reaches about 8
mph (12 km/h). D The warning light comes on during driving, but it goes out immediately and remains off.

When driving with an insufficient battery voltage such as when the en- gine is jump started, the ABS warning light may come on. This is due to the low battery voltage and does not indicate a malfunction. When the battery becomes fully charged, the light will go out.

Parking your vehicle

WARNING

D Never leave unattended children or pets in the vehicle. They could accidentally injure themselves or others through inadver- tent operation of the vehicle. Also, on hot or sunny days, the tem- perature in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to them. D Do not park the vehicle over flammable materials such as dry grass, waste paper or rags, as they may burn easily if they come near hot engine or exhaust system parts. D Be sure to stop the engine if you take a nap in the vehicle. If engine exhaust gas enters the passenger compartment, occu- pants in the vehicle could die from carbon monoxide (CO) con- tained in the exhaust gas.

CAUTION

Never drive while the parking brake is set because this will cause unnecessary wear on the brake linings. Before starting to drive, always make sure that the parking brake has been fully released.

To set the parking brake, press the brake pedal firmly and hold it down

– CONTINUED –

7-25

Legacy U.S.A. (66L) A2260BE–B

while fully pulling up the parking brake lever.

HB4001BA

To release the parking brake, pull the lever up slightly, press the release button, then lower the lever while keeping the button pressed. When the parking brake is set while the engine is running, the parking brake warning light comes on. After starting the vehicle, be sure that the warning light has gone out before the vehicle is driven. Refer to the “Warning and indicator lights” section (chapter 3).

When parking your vehicle, always set the parking brake firmly and put the shift lever in the “1” (1st) for an upgrade or “R” (Reverse) for a down- grade for manual transmission vehicles, or in the “P” (Park) position for automatic transmission vehicles. Always set the parking brake firmly when parking your vehicle. Never rely on the transmission alone to hold the vehicle.

HB4014AA

HB4015AA

7-26

Legacy U.S.A. (66L) A2260BE–B

Starting and operating

When parking on a hill, always turn the steering wheel. When the vehicle is headed up the hill, the front wheels should be turned away from the curb. When facing downhill, the front wheels should be turned into the curb.

Cruise control (if equipped)

WARNING

Do not use the cruise control under any of the following condi- tions. This may cause loss of vehicle control: D driving up or down a steep grade D driving on slippery or winding roads D driving in heavy traffic

Cruise control enables you to maintain a constant vehicle speed without holding your foot on the accelerator pedal and it is operative when the vehicle speed is 25 mph (40 km/h) or more. Make sure the main switch is turned “OFF” when the cruise control is not in use to avoid unintentionally by setting the cruise control.

B To set cruise control

Cruise control lever

HB3002BB

HG0312

1. Push the “CRUISE” main switch. 2. Depress the accelerator pedal until the vehicle reaches to the de- sired speed.

– CONTINUED –

7-27

Legacy U.S.A. (66L) A2260BE–B

3. Push the control lever downward in the “SET, COAST” direction and release it. Then release the accelerator pedal. The vehicle will maintain the desired speed.

Vehicle speed can be temporarily increased while driving with the cruise control activated. Simply depress the accelerator pedal to ac- celerate the vehicle. When the accelerator pedal is released, the ve- hicle will return to and maintain the previous cruising speed.

B To temporarily cancel the cruise control There are four ways to cancel the cruise control temporarily:

D Depress the brake pedal. D Pull the control lever in the “CANCEL” direction. (if so equipped) D Depress the clutch pedal (manual transmission vehicles only). D Shift the selector lever into the “N” position (automatic transmis- sion vehicles only).

To resume the cruise control after it has been temporarily canceled and with vehicle speed of about 20 mph (32 km/h) or more, push the control lever upward in the “ACCEL, RESUME” direction to return to the original cruising speed automatically.

B To turn off the cruise control There are two ways to turn off the cruise control:

D Push the main switch again. D Turn the ignition switch to the “ACC” position (but only when the vehicle is completely stopped).

B To change the cruising speed n To increase the speed 1. Push the control lever upward in the “ACCEL, RESUME” direction and hold it until the vehicle reaches the desired speed.

When the difference between the actual vehicle speed and the set speed is less than 4 mph (6.8 km/h), the set speed can be increased 1 mph (1.6 km/h) each time by pressing the control lever upward in the “ACCEL, RESUME” direction quickly within a half second.

2. Push the control lever downward in the “SET, COAST” direction

7-28

Legacy U.S.A. (66L) A2260BE–B

Starting and operating

once. Now the desired speed is set and the vehicle will keep running at that speed without depressing the accelerator pedal.

n To decrease the speed 1. Push the control lever downward in the “SET, COAST” direction and hold it until the vehicle reaches the desired speed.

When the difference between the actual vehicle speed and the set speed is less than 4 mph (6.8 km/h), the set speed can be lowered 1
mph (1.6 km/h) each time by pressing the control lever downward in the “SET, COAST” direction quickly within a half second.

2. When the speed decreases to the desired speed, press the control lever downward in the “SET, COAST” direction once. Now the desired speed is set and the vehicle will keep running at that speed without depressing the accerelator pedal.

– CONTINUED –

7-29

Legacy U.S.A. (66L) A2260BE–B

Driving tips

New vehicle break-in driving – the first 1,000 miles (1,600 km)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel economy hints Engine exhaust gas (Carbon monoxide) Catalytic converter Periodic inspections Driving in foreign countries Driving tips for AWD vehicles Off road driving Winter driving

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Snow tires Tire chains Rocking the vehicle Loading your vehicle

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vehicle capacity weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GVWR and GAWR (Gross Vehicle Weight Rating and Gross Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Roof rail and crossbar (if equipped)

Weight Rating)

Trailer hitch (if equipped) Trailer towing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8-2
8-3
8-3
8-4
8-5
8-5
8-6
8-7
8-10
8-13
8-14
8-15
8-15
8-16

8-17
8-18
8-22
8-26

Legacy U.S.A. (66L) A2260BE–B

New vehicle break-in driving – the first 1,000 miles (1,600 km)

The performance and long life of your vehicle are dependent on how you handle and care for your vehicle while it is new. Follow these instructions during the first 1,000 miles (1,600 km): D Do not race the engine.

B Break-in engine speed limit D Vehicle with tachometer Never exceed 4,000 rpm engine speed except for brief acceleration in an emergency. D Vehicle without tachometer (for manual transmission) Do not exceed the speed limits below for each gear position except for brief acceleration in an emergency.

1st

22 (35)

2nd

37 (60)

3rd

50 (80)

mph (km/h)

4th

65 (105)

D Vehicles without tachometer (for automatic transmission) Try to drive at moderate speeds while accelerating and braking smoothly. Proper gears are selected automatically according to the driving conditions.

D Do not drive at one constant engine or vehicle speed for a long time, either fast or slow. D Avoid starting suddenly and rapid acceleration, except in an emer- gency. D Avoid hard braking, except in an emergency.

The same break-in procedures should be applied to a newly installed or overhauled engine or when brake pads or brake linings are replaced with new ones.

8-2

Legacy U.S.A. (66L) A2260BE–B

Driving tips

Fuel economy hints

The following suggestions will help to save your fuel.

D Select the proper gear position for the speed and road conditions. D Avoid sudden acceleration or deceleration. Always accelerate gently until you reach the desired speed. Then try to maintain that speed for as long as possible. D Do not pump the accelerator and avoid racing the engine. D Avoid unnecessary engine idling. D Keep the engine properly tuned. D Keep the tires inflated to the correct pressure shown on the tire plac- ard, which is located under the door latch on the driver’s side. Low pres- sure will increase tire wear and fuel consumption. D Use the air conditioner only when necessary. D Keep the front and rear wheels in proper alignment. D Avoid carrying unnecessary luggage or cargo.

Engine exhaust gas (Carbon monoxide)

WARNING

D Never inhale engine exhaust gas. Engine exhaust gas contains carbon monoxide, a colorless and odorless gas which is danger- ous, or even lethal, if inhaled. D Always properly maintain the engine exhaust system to pre-