2012 Subaru Impreza Owners Manual

is below the “MIN” mark in the level reservoir, do not drive the vehicle. Have the vehicle towed to the nearest SUBARU dealer for repair.

this occurs,

If

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

3-18 Instruments and controls

! Electronic Brake Force Distribution

(EBD) system warning

The brake system warning light also illuminates if a malfunction occurs in the EBD system. In that event, it illuminates together with the ABS warning light. The EBD system may be malfunctioning if the brake system warning light and ABS warning light illuminate simultaneously during driving. Even if the EBD system fails, the conven- tional braking system will still function. However, the rear wheels will be more prone to locking when the brakes are applied harder than usual and the vehi- cle’s motion may therefore become some- what harder to control. If the brake system warning light and ABS warning light illuminate simultaneously, take the following steps. 1. Stop the vehicle in the nearest safe, flat place. 2. Shut down the engine, apply the parking brake and then restart it. 3. Release the parking brake. If both warning lights turn off, the EBD system may be malfunctioning. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights illuminate again and remain illuminated after the engine

If

the brake fluid level

has been restarted, shut down the engine again, apply the parking brake, and check the brake fluid level. If the brake fluid level is not below the 5. “MIN” mark, the EBD system may be malfunctioning. Drive carefully to the nearest SUBARU dealer and have the system inspected. 6. is below the “MIN” mark, DO NOT drive the vehicle. Instead, have the vehicle towed to the nearest SUBARU dealer for repair. & Low fuel warning light The low fuel warning light illuminates when the tank is nearly empty, at approxi- mately 2.6 US gal (10.0 liters, 2.2 Imp gal). It only operates when the ignition switch is in the “ON” position.

CAUTION

Promptly put fuel in the tank when- ever the low fuel warning light illuminates. Engine misfires as a result of an empty tank could cause damage to the engine.

NOTE This light does not turn off unless the tank is replenished up to an internal

Black plate (140,1)

fuel quantity of approximately 3.5 US gal (13 liters, 2.9 Imp gal).

& Hill start assist warning

light (MT models)/Hill start assist OFF indica- tor light (MT models)

! Hill start assist warning light While the engine is running, if there are any malfunctions in the Hill start assist system, the warning light will illuminate.

WARNING

When the Hill start assist warning light illuminates, have the vehicle inspected at an authorized SUBARU dealer.

! Hill start assist OFF indicator light While the Hill start assist system is deactivated, the Hill start assist OFF indicator light illuminates continuously to inform the driver that the Hill start assist system is not operational.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

& Door open warning

light

The warning light illuminates if any door, the rear gate (5-door models) or trunk lid (4-door models) is not fully closed. This function is effective even if the ignition switch is in the “LOCK” or “ACC” position, or the key is removed from the ignition switch.

Always make sure this light is not illumi- nated before you start to drive. & All-Wheel Drive warn- ing light (CVT models)

This light illuminates when All-Wheel Drive is disengaged and the drive me- chanism is switched to Front Wheel Drive for maintenance or similar purposes. It flashes if the vehicle is driven with tires of differing diameters fitted on the wheels or with an excessively low air pressure in any of the tires.

CAUTION

whether any of excessively low inflation pressure.

the tires has an

& Power steering warn-

ing light

This warning light illuminates when the ignition switch is turned to the “ON” position and turns off after the engine has started. This indicates that the warn- ing system is working properly.

While the engine is running, this warning light illuminates when a malfunction has been detected in the electric power steer- ing system.

CAUTION

When the power steering warning light is illuminated, there may be more resistance when the steering wheel is operated. Drive carefully to the nearest SUBARU dealer and have the vehicle inspected immedi- ately.

Continuing to drive with the AWD warning light flashing can damage the powertrain. If the AWD warning light starts to flash, promptly park in a safe place and check whether the tires have differing diameters and

NOTE If the steering wheel is operated in the following ways, the power steering control system may temporarily limit the power assist in order to prevent the

Black plate (141,1)

Instruments and controls 3-19

system components, such as the con- trol computer and drive motor, from overheating. . The steering wheel is operated fre- quently and turned sharply while the vehicle is maneuvered at extremely low speeds, such as while frequently turn- ing the steering wheel during parallel parking. . The steering wheel remains in the fully turned position for a long period of time.

At this time, there will be more resis- tance when steering. However this is not a malfunction. Normal steering force will be restored after the steering wheel is not operated for a while and the power steering control system has an opportunity to cool down. However, if the power steering is operated in a non-standard way which causes power assist limitation to occur too fre- quently, that may result in a malfunc- tion of the power steering control system.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (142,1)

3-20 Instruments and controls

& Vehicle Dynamics

Control warning light/ Vehicle Dynamics Con- trol operation indicator light

! Vehicle Dynamics Control warning

light

CAUTION

The Vehicle Dynamics Control sys- tem provides its ABS control through the electrical circuit of the ABS system. Accordingly, if the ABS is inoperative, the Vehicle Dynamics Control system becomes unable to provide ABS control. As a result, the Vehicle Dynamics Control system also becomes inoperative, causing the warning light to illuminate. Though both the Vehicle Dynamics Control and ABS systems are inop- erative in this case, the ordinary functions of the brake system are still available. You will be safe while driving with this condition, but drive carefully and have your vehicle checked at a SUBARU dealer as soon as possible.

NOTE . If the electrical circuit of the Vehicle Dynamics Control system itself mal- functions, the warning light only illumi- nates. At this time, the ABS (Anti-lock Brake System) remains fully opera- tional. . The warning light illuminates when the electronic control system of the ABS/Vehicle Dynamics Control system malfunctions. The Vehicle Dynamics Control system is probably inoperative under any of the following conditions. Have your vehicle checked at a SUBARU dealer immedi- ately. . The warning light does not illuminate when the ignition switch is turned to the “ON” position. . The warning light illuminates while the vehicle is running. NOTE If the warning light behavior is as described in the following examples, the Vehicle Dynamics Control system may be considered normal. . The warning light illuminates when the ignition switch is turned to the “ON” position and turns off approxi- mately 2 seconds after the engine has started.

. The warning light illuminates right after the engine is started but turns off immediately, remaining off. . The warning light illuminates after the engine has started and turns off while the vehicle is subsequently being driven. . The warning light illuminates during driving, but it turns off immediately and remains off. . The warning light illuminates when the engine has stalled and continues to illuminate after the engine has been restarted. However, it will turn off once the vehicle starts moving. ! Vehicle Dynamics Control opera-

tion indicator light

The indicator light flashes during activa- tion of the skid suppression function and during activation of the traction control function. NOTE . The light may remain illuminated for a short period of time after the engine has been started, especially in cold weather. This does not indicate the existence of a problem. The light should turn off as soon as the engine has warmed up. . The indicator light illuminates when the engine has developed a problem

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

and the CHECK ENGINE warning light/ malfunction indicator light is on. The Vehicle Dynamics Control system is probably malfunctioning under the follow- ing condition. Have your vehicle checked at a SUBARU dealer as soon as possible. . The light does not turn off even after the lapse of several minutes (the engine has warmed up) after the engine has started. & Vehicle Dynamics

Control OFF indicator light The light illuminates when the Vehicle Dynamics Control OFF switch is pressed to deactivate the Vehicle Dynamics Con- trol system.

The Vehicle Dynamics Control system is probably malfunctioning under any of the following conditions. Have your vehicle checked at a SUBARU dealer immedi- ately. . The light does not illuminate when the ignition switch is turned to the “ON” position. . The light does not turn off even once several seconds have elapsed after the ignition switch has been turned to the “ON” position.

& Security indicator light This indicator light shows the status of the alarm system. It also indicates operation of the immobilizer system. ! Alarm system It blinks to show the driver the operational status of the alarm system. For detailed information, refer to “Alarm system” F2- 12. ! Immobilizer system The security indicator light starts blinking in the following conditions. . approximately 60 seconds after the ignition switch is turned from the “ON” position to the “ACC” or “LOCK” position . immediately after the ignition key is pulled out

If the indicator light does not blink in the above conditions, it may indicate that immobilizer system may be malfunction- ing. Contact your nearest SUBARU dealer immediately.

In the event that an unauthorized key (for is example, an unauthorized duplicate) used, illumi- nates. For details about the immobilizer system, refer to “Immobilizer” F2-2.

the security indicator light

Black plate (143,1)

Instruments and controls 3-21

NOTE . The security indicator light remains off in the following conditions. This is normal and does not indicate a mal- function.

– while the engine is running – for approximately 60 seconds after the ignition switch is turned from the “ON” position to the “ACC” or “LOCK” position

. Even if the security indicator light flashes irregularly or its fuse blows (the light does not flash if its fuse is blown), the immobilizer system will function normally.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

3-22 Instruments and controls

& Shift-up indicator light

(MT models)

While driving, nates and informs the driver about upshift timing for fuel-efficient driving.

this indicator light

illumi- the

The shift-up indicator can be activated or deactivated by performing the following procedure. 1. Turn the ignition switch to the “LOCK” or “ACC” position. 2. Press the trip knob to show “ “

” on the trip meter display.

” or

The display can be switched as shown in the following sequence by pressing the trip knob.

Black plate (144,1)

& Select lever/gear position in-

dicator (CVT models)

1) Upshift indicator 2) Downshift indicator

This indicator shows the position of the select lever.

For models with manual mode, when the manual mode is selected, the gear posi- tion indicator (which shows the current gear selection) and the upshift/downshift indicator light up. Refer to “Continuously variable transmission” F7-18. & Turn signal indicator

lights

These lights show the operation of the turn signal or lane change signal.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

*1: They cannot be displayed when the ignition switch is in the “ON” position.

*2: MT models only

3. To change the current setting, press the trip knob for at least 2 seconds.

: Activated : Deactivated

NOTE . The initial setting for the shift-up indicator has been set for activation “ ” at the time of shipment from the factory. . It is not possible to change the setting of the shift-up indicator when the ignition switch is in the “ON” position. Change the setting when the ignition switch is in the “LOCK” or “ACC” position.

If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to “Replacing bulbs” F11-37. & High beam indicator

light

This light shows that the headlights are in the high beam mode. This indicator light also illuminates when the headlight flasher is operated. & Cruise control indica- tor light (if equipped)

This light illuminates when the “CRUISE” main switch is pressed to activate the cruise control function. For details, refer to “To set cruise control” F7-37. NOTE If this indicator light and the CHECK ENGINE warning light/malfunction in- dicator light flash simultaneously dur- ing driving, have the vehicle checked by your nearest SUBARU dealer.

& Cruise control set in-

dicator light (if equipped)

This light illuminates when vehicle speed has been set to use the cruise control function. Refer to “To set cruise control” F7-37. & Automatic headlight beam leveler warning light (models with HID headlights)

This light illuminates when the automatic headlight beam leveler does not operate normally. If this light illuminates while driving or does not turn off approximately 3 seconds after turning the ignition switch to the “ON” position, have your vehicle inspected at your SUBARU dealer. & Front fog light indicator

light (if equipped)

This indicator light front fog lights are illuminated.

illuminates while the

Black plate (145,1)

Instruments and controls 3-23

& Headlight indicator light (if equipped)

This indicator light illuminates under the following conditions. . when the light switch is turned to the “ . when the light control switch is in the “AUTO” position and the headlights illumi- nate automatically

” position

” or “

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (146,1)

3-24 Instruments and controls

Information display (if equipped)

& Outside temperature indica-

tor

! Road surface freeze warning indi-

cation

1) Outside temperature indicator 2) Driving information display 3) Clock

With the ignition switch in the“ ACC” position, the clock appears on the display. With the ignition switch in the “ON” position, the outside temperature indica- tor, driving information display and clock all appear on the display.

1) U.S.-spec. models 2) Except U.S.-spec. models

1) U.S.-spec. models 2) Except U.S.-spec. models

The outside temperature indicator shows the outside temperature in a range from −40 to 1228F (−40 to 508C). The indicator can give a false reading under any of the following conditions. . When there is too much sun. . During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately following a shut- down. . When the actual outside temperature falls outside the specified indicator range.

lower,

When the outside temperature drops to 378F (38C) or the temperature indication flashes to show that the road surface may be frozen. If the outside temperature drops to 378F (38C) or lower while the display is giving an indication other than the outside temperature, the display switches to the outside temperature indication and flashes for 5 seconds before returning to its original indication. the display is already indicating an If outside temperature of 378F (38C) or lower when the ignition switch is turned to the

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (147,1)

Instruments and controls 3-25

that can be driven taking into account the amount of fuel remaining in the tank and the average rate of fuel consumption. When the low fuel warning light illumi- nates, the driving range display flashes for 5 seconds. (The display first switches to the driving range value if a different value was previously displayed.)

the indication does not

“ON” position, flash. NOTE The outside temperature indication may differ from the actual outside temperature. The road surface freeze warning indication should be treated only as a guide. Be sure to check the condition of the road surface before driving.

& Driving information display

! Driving range on remaining fuel

1)

Information display switching knob

With the ignition switch in the “ON” position, each successive press of the information display switching knob toggles the display in the following sequence.

1) U.S.-spec. models 2) Except U.S.-spec. models

The driving range indicates the distance

1) U.S.-spec. models 2) Except U.S.-spec. models the driving range is shown as “

”, If there is only a tiny amount of fuel left in the tank. You must refuel the vehicle immedi- ately. NOTE The driving range on remaining fuel is only a guide. The indicated value may differ from the actual driving range on

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

3-26 Instruments and controls

remaining fuel, so you must immedi- ately fill the tank when the low fuel warning light illuminates. ! Average fuel consumption

1) U.S.-spec. models 2) Except U.S.-spec. models

This display shows the average rate of fuel consumption since the trip meter was last reset.

1)

Trip knob

Pressing the trip knob toggles the display between the average fuel consumption corresponding to the A trip meter display and the average fuel consumption corre- sponding to the B trip meter display. When either of the trip meter displays is reset, the corresponding average fuel consumption value is also reset. NOTE . The indicated values vary in accor- dance with changes in the vehicle’s running conditions. Also, the indicated values may differ slightly from the actual values and should thus be treated only as a guide. . When either trip meter display is reset, the average fuel consumption

Black plate (148,1)

corresponding to that trip meter dis- play is not shown until the vehicle has subsequently covered a distance of 1
mile (or 1 km). ! Current fuel consumption

1) U.S.-spec. models 2) Except U.S.-spec. models

This indication shows the rate of consumption at the present moment.

fuel

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

! Journey time

The journey time shows the time that has elapsed since the ignition switch was turned to the “ON” position.

display is giving a reading other than the journey time, the display switches to the journey time, flashes for 5 seconds, and returns to its original reading each time a complete hour has elapsed. NOTE The journey time is reset when the ignition switch is turned to the “LOCK” position. It is also reset if the ignition switch is turned to the “LOCK” or “ACC” position prior to restarting of the engine. ! Average vehicle speed

The journey time indication flashes each time a complete hour has elapsed. If the

This display shows the average vehicle speed since the trip meter was last reset.

1) U.S.-spec. models 2) Except U.S.-spec. models

Black plate (149,1)

Instruments and controls 3-27

1)

Trip knob

Pressing the trip knob toggles the display between the average vehicle speed cor- responding to the A trip meter display and the average vehicle speed corresponding to the B trip meter display. When either of the trip meter displays is reset, the corresponding average vehicle speed value is also reset. NOTE When either trip meter display is reset, the average vehicle speed correspond- ing to that trip meter display is not shown until the vehicle has subse- quently covered a distance of 1 mile (or 1 km).

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

3-28 Instruments and controls

! Turn off display of driving informa-

tion display

The driving information display can be turned off. To turn off the display, turn the ignition switch to the “LOCK” position and press the “+” button adjacent to the clock display for approximately 5 seconds. Then, the driving information display and the clock display will blink for 3 seconds to notify you that the driving information display has been turned off. To restore the driving information display, once again press the “+” button for approximately 5 seconds. NOTE . The initial display setting of the driving information display has been set to operational at the time of ship- ment from the factory. . The average fuel consumption and average vehicle speed are calculated even while the driving information dis- play is not displayed. . Even if you turn off the driving information display, the display will automatically turn on when the battery voltage is disconnected and then re- connected for battery replacement or fuse replacement.

& Clock

To adjust the time shown by the clock, press the “+” button or “−” button. If you press the “+” button, the indicated time will change in one-minute increments. If you press the “−” button, the indicated time will change in one-minute decrements. If you keep the button pressed, the rate at which the indicated time changes will speed up.

The clock can be set to 12-hour or 24-hour clock displays. Perform the following procedure to switch the display format. 1. Place the ignition switch in the “LOCK” position. 2. Press and hold the “−” button that is located near the clock display for approxi- mately 5 seconds. The clock display will then start to flash.

Black plate (150,1)

3. While the clock display is flashing, press and hold the “+” button for approxi- mately 2 seconds. The clock format will then change. 4. The clock display will continue to flash for approximately 3 seconds to inform you that the clock display has been changed. If you want to change the clock display again, press and hold the “+” button for approximately 2 seconds while the clock display is flashing.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Multi function display (Non-US vehicles only; if equipped)

malfunction is detected. In addition, sev- eral settings for the displayed content can be performed.

WARNING

. Always pay adequate attention to safe driving when operating the multi function display while the vehicle is in motion. When opera- tion of the multi-function display is disturbing your awareness and ability to concentrate on driving, stop the vehicle before perform- ing operations on the screen. Also, do not concentrate on the display while driving. Doing so may cause you to look away from the road and could result in an accident.

. Adjust the beep volume so that you can hear noises in the en- vironment outside while driving. If you drive the vehicle without hearing noises in the environ- ment outside, an accident may occur.

Various information will be shown on the multi function display. Also, a warning message will appear on the display if a

Multi function display 1) Outside temperature indicator 2) 3)

Information reminder Top display (For the display setting, refer

Black plate (151,1)

Instruments and controls 3-29

to “Top display setting” F3-44.)

4) Clock 5) Driving information display (For the dis- played contents, refer to “Basic screens” F3-32.)

Control switch 1) Up (select) 2) Set (enter) 3) Down (select)

& Basic operation ” of the control By operating “ ” or “ switch, the screens and selection items can be switched. When the “ /SET” switch is pulled toward you, the item can be selected and set.

If there are some useful messages, such as reminder information, vehicle informa- they will tion, warning information, etc., – CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

3-30 Instruments and controls

interrupt the current screen, and appear on the display accompanied by a beep. If such a screen is displayed, take proper action according to the message shown on the screen.

Black plate (152,1)

& Ending screen

return to the The warning screen will original screen after a few seconds. If the warning screen can be displayed again, an information reminder “ ” will appear on the upper the the message marked display. To recall with “ /SET” switch on the steering wheel toward you.

” on the display, pull the “

left part of

& Opening screen is unlocked and the When the door driver’s door the opening screen will appear for approximately 20
seconds.

is opened,

NOTE . The opening screen will disappear when the ignition switch is turned to the “ON” position while the opening screen is displayed. . If any of the doors (including the rear gate) is opened while the opening screen is displayed, the door ajar warning will appear. . The opening screen can be set to on or off. For details, refer to “Bypass screen setting” F3-50.

When the ignition switch is turned to the “LOCK” position, the “Goodbye” screen will appear for approximately 3 seconds.

& Self-check screen When the ignition switch is turned to the “ON” position, the vehicle self-check is performed. The screens corresponding to the following items will appear one after another for approximately 2 seconds each.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

1) Windshield washer fluid 2) Brake fluid 3) Engine oil 4) Oil filter 5) 6)

Tire Inspection and maintenance

If there is no warning message, the self- check is complete without notification.

Example of notification

there is a warning message or a If maintenance notification, it will appear for approximately 3 seconds. Take the appro- priate actions based on the messages indicated. NOTE The self-check screen can be set to on or off. For details, refer to “On/Off setting” F3-53.

Black plate (153,1)

Instruments and controls 3-31

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

3-32 Instruments and controls

Black plate (154,1)

& Basic screens By operating the “ switch is pulled and held, the selection screen can be displayed.

” or “

” switch on the steering wheel, you can switch the screen that is always displayed. Also, when the “

/SET”

Fuel consumption screen

ECO gauge screen

ECO history screen

Displays the following information

a value for the average fuel consumption corresponding to the driving distance of each trip meter a bar indicator showing the current fuel consumption a value for the driving range based on remaining fuel

The displayed location can be customized. For details, refer to “Fuel consumption screen setting” F3-45.

Displays the fuel economy level for the current driving conditions using the motion of a gauge pointer. If the gauge pointer moves toward the green side, this indicates better fuel efficiency.

Displays average and current fuel consumption histories. The time range of the history can be customized from 30 minutes (minimum) to 120 minutes (maximum). For details, refer to “Economy history setting” F3-46.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (155,1)

Instruments and controls 3-33

Vehicle activation status screen

Displays the following vehicle information.

steering angle and driving wheel status activation status of the ABS (Anti-lock Brake System) activation status of the Vehicle Dynamics Control system

Triple meter screen

Guidance screen

Displays three optional pieces of information that can be selected from the following items. . Average vehicle speed Lifetime fuel consumption . Engine oil temperature . Accelerator opening ratio . Block time . Block distance . Block fuel consumption For details, refer to “Triple meter setting” F3-48.

/SET” switch is pulled and held, the selection screen can be

When the “ displayed. The displayed contents can be set or customized from the selection screen. For details, refer to “Selection screen” F3-35.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

3-34 Instruments and controls

Clock screen

Black plate (156,1)

In addition to the clock, the outside temperature and average fuel consumption are also displayed. You can select between analog and digital formats. For details, refer to “Clock screen setting” F3-49.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (157,1)

Instruments and controls 3-35

& Selection screen Select an item by operating the “ be displayed.

” or “

” switch. When the “

/SET” switch is pulled and held, the setting screen for each menu can

Top menu

Menu option

Description

Date

Display

Screen Setting

Date

Birthday

Anniversary

Return

Brightness

Contrast

Screen Off

Beep

Return

Top Display

Cons

Eco History

Triple Meter

Clock

Bypass Screen

Languages

Return

Set and adjust the time and date. 12h or 24h format can be selected.

Set a birthday.

Set an anniversary day.

Return to the top menu.

Adjust the brightness.

Adjust the contrast.

Turn the screen on or off.

+5 ↔ −5
+5 ↔ −5
On or Off

Adjust the beep sound volume.

High, Low or Off

Return to the top menu.

Set and customize the top display informa- tion contents.

Avg Cons, Inst Cons, Range or Off

Customize the fuel consumption information display.

Set and customize the time of logging fuel consumption history.

30 min, 60 min or 120 min

Set and customize the triple meter.

Select the clock format.

Analog, Digital or Off

Set the bypass screen for each item.

On or Off

Select the display language.

English or French

Return to the top menu.

Page

3-37

3-38

3-39
—

3-41

3-42

3-42

3-43
—

3-44

3-45

3-46

3-48

3-49

3-50

3-51
—

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (158,1)

3-36 Instruments and controls

Top menu Maintenance

Menu option

Description

Engine Oil

Oil Filter

Tires

Set and adjust the oil maintenance notification date.

Set and adjust the oil filter maintenance notification date.

Set and adjust the tire maintenance notification date.

Maintenance Schedule

Set and adjust the vehicle maintenance notification date.

On/Off

Clear All Settings

Return

Driving History

Set

Turn on or off the self-check screen that is activated when the ignition switch is turned to the “ON” position. Clear all settings for maintenance items.

On or Off

Yes or No

Return to the top menu.

Register and overwrite the driving record.

Return

Return to the top menu.

Car Setting

Hazard Warning Flasher

Set the hazard warning flasher.

On or Off

Defogger

Interior Light

Auto Light Sensor (models with auto on/off head- lights)

Set and customize the operation of the defogger.

15 minutes or Continuous

Set and customize the interior light off delay timer.

10, 20, 30 seconds or Off

Set and customize the sensitivity of the auto light sensor.

Low, Mid, High or Max

Return

Return to top menu.

Initialize

Reset to Defaults

Reset all settings to the default settings.

Yes or No

Lifetime Fuel Consumption Reset Clear logged lifetime fuel consumption data. Yes or No

Return

Return

—

Return to the top menu.

Return to the top menu.

Page

3-52

3-53

3-53

3-53

3-53

3-54
—

3-55
—

3-57

3-58

3-59

3-60

—

3-62

3-63
—

—

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (159,1)

Instruments and controls 3-37

” or “

” switch.

& Date and time settings The items in the date and time settings can be set. To change the items, operate the “ NOTE . The “Date” item must be set to display the “Birthday”, “Anniversary” and notifications for vehicle mainte- nance. . The “Birthday” and “Anniversary” items can be entered after the “Date” item has been set. ! Preparation for date setting 1. Turn the ignition switch to the “ON” /SET” switch position and pull toward you for more than 2 seconds.

the “

operate the “ “Date” item. Then, pull the “ toward you.

” or “

” switch to show the /SET” switch

! Current date and time setting 1. Perform the preparation steps accord- ing to “Preparation for date setting” F3- 37.

3. Select the item to set by operating the “ SET” switch toward you.

” switch, and then pull the “

” or “

2. Operate the “ ” switch to select the “Date” item, and then pull the “

/SET” switch toward you.

” or

“

2. After the selection screen is displayed,

4. Select a number by operating the “ or “ switch toward you.

” switch, and then pull the “

” /SET”

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (160,1)

3-38 Instruments and controls

seconds.

! Birthday setting 1. Perform the preparation steps accord- ing to “Preparation for date setting” F3- 37.

5. After entering the date and time, select “Set” by operating the “ ” switch and confirm the setting by pulling the “ /SET” switch toward you.

6. The system will notify you that the setting is complete for approximately 3

2. Operate the “ ” switch to select the “Birthday” item, and then pull the “

/SET” switch toward you.

” or

“

3. Select the item to set by operating the “ SET” switch toward you.

” switch, and then pull the “

” or “

4. Select numbers by operating the “ or “ switch toward you.

” switch, and then pull the “

” /SET”

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (161,1)

Instruments and controls 3-39

seconds.

If a birthday is approaching, the following screen will be displayed accompanied by a beep when the ignition switch has been turned to the “ON” position.

5. After entering the date by repeating step 4, select “Set” by operating the “ ” switch and confirm the setting by pulling the “

/SET” switch toward you.

From 1 to 7 days prior to the birthday

6. The system will notify you that the setting is complete for approximately 3

On a birthday NOTE If “_ _” is selected for either the “Month” or “Day” item instead of numbers, the birthday notification is deactivated. ! Anniversary setting 1. Perform the preparation steps accord- ing to “Preparation for date setting” F3- 37.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

3-40 Instruments and controls

” switch to the “Anniversary” item, and then

” or

2. Operate the “ select pull the “

/SET” switch toward you.

“

Black plate (162,1)

the “

/SET” switch toward you.

6. The system will notify you that the setting is complete for approximately 3
seconds.

If an anniversary is approaching, the following screen will be displayed accom- panied by a beep when the ignition switch has been turned to the “ON” position.

4. Select numbers by operating the “ or “ switch toward you.

” switch, and then pull the “

” /SET”

3. Select the item to set by operating the “ SET” switch toward you.

” switch, and then pull the “

” or “

5. After entering the date by repeating step 4, select “Set” by operating the “ ” switch and confirm the setting by pulling

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

NOTE If “_ _” is selected for either the “Month” or “Day” item instead of numbers, the anniversary notification is deactivated. ! Clearing birthday or anniversary 1. Perform the preparation steps accord- ing to “Preparation for date setting” F3-37
and display “Birthday” or “Anniversary” on the screen. 2. When “_ _” is selected for either the “Month” or “Day” item instead of numbers, the setting of “Birthday” or “Anniversary” is cleared.

& Image quality and volume

settings

From 1 to 7 days prior to the anniversary

The items in the image quality and volume settings can be set. To change the items, operate the “ ! Preparation for image quality and

” switch.

” or “

volume settings

On an anniversary

1. Turn the ignition switch to the “ON” /SET” switch position and pull toward you for more than 2 seconds.

the “

Black plate (163,1)

Instruments and controls 3-41

2. After the selection screen is displayed, operate the “ ” switch to show the “Display” item. Then, pull /SET” switch toward you.

the “

” or “

! Brightness setting 1. Perform the preparation steps accord- ing to “Preparation for image quality and volume settings” F3-41.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

3-42 Instruments and controls

toward you.

! Contrast setting 1. Perform the preparation steps accord- ing to “Preparation for image quality and volume settings” F3-41.

2. Operate the “ ” switch to select the “Brightness” item, and then pull the “

/SET” switch toward you.

” or

“

2. Operate the “ ” switch to select the “Contrast” item, and then pull the “

/SET” switch toward you.

” or

“

3. Select a brightness level by operating the “ ” switch, and confirm the setting by pulling the “ /SET” switch

” or “

Black plate (164,1)

3. Select a contrast level by operating the “ ” switch, and confirm the setting by pulling the “ /SET” switch toward you.

” or “

! Screen OFF setting 1. Perform the preparation steps accord- ing to “Preparation for image quality and volume settings” F3-41.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (165,1)

Instruments and controls 3-43

2. Operate the “ ” switch to select the “Volume” item, and then pull the “

/SET” switch toward you.

” or

“

3. Pull the “

/SET” switch toward you.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

2. Operate the “ ” switch to select the “Screen OFF” item, and then pull the “

/SET” switch toward you.

” or

“

3. Pull toward you.

the “

/SET” switch once more

4. The screen is turned off.

”, “

” or “

Restoring the screen When the “ /SET” switch is pulled toward you after the ignition switch is turned to the “ON” position, the screen will be restored. The screen is restored with the basic screen that was displayed when the screen was turned off. While the screen is off, a warning message will be displayed if necessary, but other screens are not displayed. ! Beep volume setting 1. Perform the preparation steps accord- ing to “Preparation for image quality and volume settings” F3-41.

3-44 Instruments and controls

Black plate (166,1)

4. Select an item by operating the “ “ switch toward you.

” switch, and then pull

the “

” or /SET”

6. The system will notify you that the setting is complete for approximately 3
seconds.

” switch, and then pull the “

& Screen settings The items in the screen settings can be set. To change the items, operate the “ ” or “ /SET” switch toward you. ! Preparation for screen settings 1. Turn the ignition switch to the “ON” /SET” switch position and pull toward you for more than 2 seconds.

the “

“Set” by operating the “

” 5. Select switch, and confirm the setting by pulling the “

/SET” switch toward you.

2. After the selection screen is displayed, operate the “ ” switch to show the “Screen Setting” item. Then, pull the “ SET” switch toward you.

” or “

! Top display setting 1. Perform the preparation steps accord- ing to “Preparation for screen settings” F3-44.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (167,1)

Instruments and controls 3-45

” or /SET”

6. The system will notify you that the setting is complete for approximately 3
seconds.

! Fuel consumption screen setting 1. Perform the preparation steps accord- ing to “Preparation for screen settings” F3-44.

4. Select an item by operating the “ “ switch toward you.

” switch, and then pull

the “

2. Operate the “ ” switch to select the “Top Display” item, and then pull the “

/SET” switch toward you.

” or

“

3. Pull the “

/SET” switch once more.

“Set” by operating the “

” 5. Select switch, and confirm the setting by pulling the “

/SET” switch toward you.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

3-46 Instruments and controls

Black plate (168,1)

2. Operate the “ ” switch to select the “Cons” item, and then pull the “

/SET” switch toward you.

” or

“

4. Select the displayed configuration by operating the “ ” switch, and then pull the “

/SET” switch toward you.

” or “

3. Pull the “

/SET” switch once more.

“Set” by operating the “

” 5. Select switch, and confirm the setting by pulling the “

/SET” switch toward you.

6. The system will notify you that the setting is complete for approximately 3
seconds.

! Economy history setting 1. Perform the preparation steps accord- ing to “Preparation for screen settings” F3-44.

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (169,1)

Instruments and controls 3-47

“Set” by operating the “

” 6. Select switch and confirm the setting by pulling the “

/SET” switch toward you.

the time of

4. Select the logged fuel consumption history by operating the “ SET” switch toward you.

” switch, and then pull the “

” or “

2. Operate the “ ” switch to select the “Eco History” item, and then pull the “

/SET” switch toward you.

” or

“

3. Pull the “

/SET” switch once more.

5. Select “Return” by operating the “ switch.

”

7. The system will notify you that the setting is complete for approximately 3
seconds.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (170,1)

3-48 Instruments and controls

! Triple meter setting 1. Perform the preparation steps accord- ing to “Preparation for screen settings” F3-44.

2. Operate the “ ” switch to select the “Triple Meter” item, and then pull the “

/SET” switch toward you.

” or

“

” or “

3. Select the setting location (left, center or right) by operating the “ ” switch, and then pull the “ /SET” switch toward you. NOTE The same item cannot be selected for the left, center or right location.

” or “

4. Select the preferred item by operating the “ ” switch, and then pull the “ If you also want to change the setting for another location, repeat steps 3 and 4.

/SET” switch toward you.

5. Select

“Set” by operating the “

”

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (171,1)

Instruments and controls 3-49

4. Select a clock style by operating the “ /SET” switch toward you.

” switches and then pull the “

switch, and confirm the setting by pulling the “

/SET” switch toward you.

6. The system will notify you that the setting is complete for approximately 3
seconds.

! Clock screen setting 1. Perform the preparation steps accord- ing to “Preparation for screen settings” F3-44.

2. Operate the “ ” switch to select the “Clock” item, and then pull the “

/SET” switch toward you.

” or

“

3. Pull the “

/SET” switch once more.

“Set” by operating the “

” 5. Select switch, and confirm the setting by pulling the “

/SET” switch toward you.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

3-50 Instruments and controls

6. The system will notify you that the setting is complete for approximately 3
seconds.

! Bypass screen setting 1. Perform the preparation steps accord- ing to “Preparation for screen settings” F3-44.

2. Operate the “ ” switch to select the “Bypass Screen” item, and then pull the “

/SET” switch toward you.

” or

“

Black plate (172,1)

” or “

” switch, and pull the “

4. Select “On” or “Off” by operating the “ /SET” switch toward you. If you want to change setting for another item, repeat steps 3 and 4.

3. Select the item to set by operating the “ SET” switch toward you.

” switches, and then pull the “

” or “

5. Select “Set” by operating the “

” or

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

“ pulling the “

” switch, and confirm the setting by

/SET” switch toward you.

Black plate (173,1)

Instruments and controls 3-51

2. Operate the “ ” switch to select the “Languages” item, and then pull the “

/SET” switch toward you.

” or

“

6. The system will notify you that the setting is complete for approximately 3
seconds.

! Language setting 1. Perform the preparation steps accord- ing to “Preparation for screen settings” F3-44.

4. Select operating the “ pull the “

the preferred language by ” switch, and then

” or “

/SET” switch toward you.

language setting is dis- 3. The current /SET” switch toward played. Pull you to enter the language selection mode.

the “

“Set” by operating the “

” 5. Select switch, and confirm the setting by pulling the “

/SET” switch toward you.

– CONTINUED –

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

Black plate (174,1)

3-52 Instruments and controls

6. The system will notify you that the setting is complete for approximately 3
seconds.

& Maintenance settings The items in the maintenance settings can be set. To change the items, operate the “ ! Preparation for maintenance set-

” switch toward you.

” or “

tings

1. Turn the ignition switch to the “ON” position, and then pull the “ /SET” switch toward you for more than 2 seconds.

2. After the selection screen is displayed, operate the “ ” switch to show the “Maintenance” item. Then, pull SET” switch toward you.

the “

” or “

2. Operate the “ ” switch to select the “Engine Oil” item, and then pull the “

/SET” switch toward you.

” or

“

! Engine oil setting 1. Perform the preparation steps accord- ing to “Preparation for maintenance set- tings” F3-52.

3. Select the setting location (month, day, year or distance) by operating the “ ” or “ /SET”

” switch, and then pull

the “

北米Model "A1120BE-B" EDITED: 2011/ 10/ 28

switch toward you.

” or ” switch and confirm the setting by

5. Select “Set” by operating the “ “ pulling the “

/SET” switch toward you.

” switch, and then pull the “

4. Select a number by operating the “ or “ switch toward you. If you also want to change the setting for another location, repeat steps 3 and 4.

” /SET”

6. The system will notify you that the setting is complete for approximately 3
seconds.

NOTE . The notification is displayed with information of both date and distance or either date or distance in accor- dance with the setting . When “_ _” is selected for either the “Month”, “Day”, “Year” or “Distance” item instead of numbers, the set noti- fication is deactivated. . If the notification continues for 15