Download PDF Manual

TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG.


1-38


US1581BA


1. Place the child restraint system in the rear seating position. 2. Run the lap and shoulder belt through or around the child restraint system following the instructions provided by its manufacturer. 3. Insert the tongue plate into the buckle until you hear a click.


Seat, seatbelt and SRS airbags


US1582BA


US1583BA


4. Take up the slack in the lap belt. 5. Pull out the seatbelt fully from the retractor to change the retractor over from the Emergency Lock- ing Retractor (ELR) to the Automatic Locking Retrac- tor (ALR) function. Then, allow the belt to rewind into the retractor. As the belt is rewinding, clicks will be heard which indicate the retractor functions as ALR.


6. Before having a child sit in the child restraint sys- tem, move it back and forth and right and left to check if it is firmly secured. Sometimes a child restraint can be more firmly secured by pushing it down into the seat cushion and then tightening the seatbelt. 7. Pull at the shoulder portion of the belt to confirm that it cannot be pulled out (ALR properly functioning).


– CONTINUED – 1-39


Seat, seatbelt and SRS airbags


Sedan


1-40


UG1087BA


UG1088BA


Wagon 8. If the child restraint system requires a top tether, latch the hook onto the top tether anchor and tighten the top tether. See the “Top tether anchorages” for ad- ditional instructions.


Seat, seatbelt and SRS airbags


(cid:132) Installing a booster seat


(cid:121) Child restraint systems and seatbelts can be- come hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check the child restraint system before you place a child in it. (cid:121) Do not leave an unsecured child restraint system in your vehicle. Unsecured child re- straint systems can be thrown around inside of the vehicle in a sudden stop, turn or accident; it can strike and injure vehicle occupants as well as result in serious injuries or death to the child.


When you install a child restraint system, fol- low the manufacturer’s instructions supplied with it. After installing the child restraint sys- tem, check to ensure that it is held securely in position. If it is not held tight and secure, the danger of your child suffering personal injury in


– CONTINUED – 1-41


UG1094BA


9. To remove the child restraint system, press the re- lease button on the seatbelt buckle and allow the belt to retract completely. The belt will return to the ELR mode. NOTE When the child restraint system is no longer in use, remove it and restore the ELR function of the retractor. That function is restored by allowing the seatbelt to retract fully.


Seat, seatbelt and SRS airbags


the event of an accident may be increased.


US1585BA


4. To remove the booster seat, press the release but- ton on the seatbelt buckle and allow the belt to retract.


US1586BA


1. Place the booster seat in the rear seating position and sit the child on it. The child should sit well back on the booster seat. 2. Run the lap and shoulder belt through or around the booster seat and the child following the instruc- tions provided by its manufacturer. 3. Insert the tongue plate into the buckle until you hear a click. Take care not to twist the seatbelt. Make sure the shoulder belt is positioned across the center of child’s shoulder and that the lap belt is posi- tioned as low as possible on the child’s hips.


1-42


(cid:121) Never use a belt that is twisted or reversed. In an accident, this can increase the risk or sever- ity of injury to the child. (cid:121) Never place the shoulder belt under the child’s arm or behind the child’s back. If an ac- cident occurs, this can increase the risk or se- verity of injury to the child. (cid:121) The seatbelt should fit snugly in order to pro- vide full restraint. Loose fitting belts are not as


effective in preventing or reducing injury. (cid:121) Place the lap belt as low as possible on the child’s hips. A high-positioned lap belt will in- crease the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen, and both can result in serious internal injury or death. (cid:121) Make sure the shoulder belt is positioned across the center of child’s shoulder. Placing the shoulder belt over the neck may result in neck injury during sudden braking or in a colli- sion.


(cid:132) Installation of child restraint systems by use of lower and tether anchorages (LATCH)


(cid:121) Child restraint systems and seatbelts can be- come hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check the child restraint system before you place a child in it. (cid:121) Do not leave an unsecured child restraint system in your vehicle. Unsecured child re-


Seat, seatbelt and SRS airbags


straint systems can be thrown around inside of the vehicle in a sudden stop, turn or accident; it can strike and injure vehicle occupants as well as result in serious injuries or death to the child.


When you install a child restraint system, fol- low the manufacturer’s instructions supplied with it. After installing the child restraint sys- tem, check to ensure that it is held securely in position. If it is not held tight and secure, the danger of your child suffering personal injury in the event of an accident may be increased.


– CONTINUED – 1-43


Seat, seatbelt and SRS airbags


UG1091BA


HS1076BA


Some types of child restraint systems can be installed on the rear seat of your vehicle without use of the seat- belts. Such child restraint systems are secured to the designated anchorages provided on the vehicle body. The lower and tether anchorages are sometimes re- ferred to as the LATCH system (Lower Anchors and Tethers for CHildren). Your vehicle is equipped with four lower anchorages (bars) and three upper anchorages (tether anchorag- es) for accommodating such child restraint systems.


The lower anchorages (bars) are used for installing a child restraint system only on the rear seat window- side seating positions. For each window-side seating position, two lower anchorages are provided. Each lower anchorage is located where the seat cush- ion meets the seatback.


1-44


Seat, seatbelt and SRS airbags


The tether anchorages (upper anchorages) are pro- vided for all the seating positions (middle and both window-side ones) of the rear seat.


You will find marks “ ” at the bottom of the rear seat seatbacks. These marks indicate the positions of the lower anchorages (bars).


UG1095BA


HS1078BA


– CONTINUED – 1-45


Seat, seatbelt and SRS airbags


HS1079BA


US1588CA


Each lower anchorage is located where the seat cush- ion meets the seatback. 1. Use the “ ” marks to locate the two lower an- chorages (bars) for the position where you want to in- stall the child restraint system.


2. While following the instructions supplied by the child restraint system manufacturer, connect the lower hooks onto the lower anchorages located at “ ” marks on the bottom of the rear seatback. When the hooks are connected, make sure the adjacent seat- belts are not caught.


1-46


Seat, seatbelt and SRS airbags


UG1098BA


US1589BA


3. [If your child restraint system is of a flexible attach- ment type (which uses tether belts to connect the child restraint system properly to the lower anchorages)] While pushing the child restraint into the seat cushion, pull both left and right lower tether belts up to secure the child restraint system firmly by taking up the slack in the belt. 4. Connect the top tether hook to the tether anchor- age and firmly tighten the tether. For information on how to set the top tether, read the following “Top tether anchorages”.


5. Before seating a child in the child restraint system, try to move seat back and forth and right and left to verify that it is held securely in position. 6. To remove the child restraint system, follow the re- verse procedures of installation. If you have any question concerning this type of child restraint system, ask your SUBARU dealer.


(cid:132) Top tether anchorages Your vehicle is equipped with three top tether anchor- ages so that a child restraint system having a top teth- er can be installed in the rear seat. When installing a child restraint system using top tether, proceed as fol- – CONTINUED – 1-47


Seat, seatbelt and SRS airbags


lows, while observing the instructions by the child re- straint system manufacturer. Since a top tether can provide additional stability by of- fering another connection between a child restraint system and the vehicle, we recommend that you use a top tether whenever one is required or available.


(cid:84) Anchorage location (cid:86) Sedan


UG1081BB


1-48


1) For left seat 2) For center seat 3) For right seat Three upper anchorages are installed on the rear shelf behind the rear seat.


(cid:86) Wagon


Seat, seatbelt and SRS airbags


1) For left seat 2) For center seat 3) For right seat


UG1082BB


– CONTINUED – 1-49


Seat, seatbelt and SRS airbags


There is an anchorage for the center seating position at the rear edge of the roof, and anchorages for each of the two window-side seating positions on the rear wall of the cargo area. (cid:84) To hook the top tether (cid:86) Sedan


(cid:86) Wagon


HS1081BA


1. Remove the headrest at the window-side seating position where the child restraint system has been in- stalled with the lower anchorages or seatbelt; lift up the headrest while pressing the release button. Store the headrest in the cargo area. Avoid placing the headrest in the passenger compartment to prevent it from being thrown around in the passenger compart- ment in a sudden stop or a sharp turn.


UG1087BA


1. Attach the child restraint top tether hook to the ap- propriate upper anchorage. 2. Tighten the top tether securely. Please contact your SUBARU dealer if you have any question regarding the installation of a child restraint system.


1-50


Seat, seatbelt and SRS airbags


2. (For both window-side seating positions) Remove the cap from the anchor fitting cover by prying it with a screwdriver.


Center


UG1526BA


UG1090BA


– CONTINUED – 1-51


Seat, seatbelt and SRS airbags


wise, the top tether cannot be fastened tightly.


UG1097BA


Window-side 3. Attach the child restraint top tether hook to the ap- propriate upper anchorage. 4. Tighten the top tether securely. Please contact your SUBARU dealer if you have any question regarding the installation of a child restraint system.


Always remove the headrest when mounting a child restraint system with a top tether. Other-


1-52


*SRS airbag (Supplemental Restraint System airbag) *SRS: This stands for supplemental restraint system. This name is used because the airbag system supple- ments the vehicle’s seatbelts.


(cid:132) Vehicle with driver’s and front passen- ger’s SRS airbags and lap/shoulder re- straints


Your vehicle is equipped with a supplemental restraint system in addition to a lap/shoulder belt at each front seating position. The supplemental restraint system (SRS) consists of two airbags (driver’s and front passenger’s frontal air- bags) or four airbags (driver’s and front passenger’s frontal airbags and driver’s and front passenger’s side airbags). These SRS airbags are designed only as a supple- ment to the primary protection provided by the seatbelt.


(cid:121) To obtain maximum protection in the event of an accident, the driver and all passengers in the


Seat, seatbelt and SRS airbags


vehicle should always wear seatbelts when the vehicle is moving. The SRS airbag is designed only as a supplement to the primary protection provided by the seatbelt. It does not do away with the need to fasten seatbelts. In combina- tion with the seatbelts, it offers the best com- bined protection in case of a serious accident. Not wearing a seatbelt increases the chance of severe injury or death in a crash even when the vehicle has the SRS airbag. For instructions and precautions concerning the seatbelt system, see the “Seatbelts” sec- tions in this chapter. (cid:121) Do not sit or lean unnecessarily close to the SRS airbag. Because the SRS airbag deploys with considerable speed – faster than the blink of an eye – and force to protect in high speed collisions, the force of an airbag can injure an occupant whose body is too close to SRS air- bag. It is also important to wear your seatbelt to help avoid injuries that can result when the SRS air- bag contacts an occupant not in proper posi- tion such as one thrown forward during pre-ac- cident braking. Even when properly positioned, there remains a possibility that an occupant may suffer minor


– CONTINUED – 1-53


Seat, seatbelt and SRS airbags


injury such as abrasions and bruises to the face or arms because of the SRS airbag deploy- ment force. (cid:121) The SRS airbags deploy with considerable speed and force. Occupants who are out of proper position when the SRS airbag deploys could suffer very serious injuries. Because the SRS airbag needs enough space for deploy- ment, the driver should always sit upright and well back in the seat as far from the steering wheel as practical while still maintaining full ve- hicle control and the front passenger should move the seat as far back as possible and sit upright and well back in the seat. (cid:121) Do not place any objects over or near the SRS airbag cover or between you and the SRS airbag. If the SRS airbag deploys, those objects could interfere with its proper operation and could be propelled inside the vehicle and cause injury.


1-54


HS1034BA


(cid:121) Put children aged 12 and under in the rear seat properly restrained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, espe- cially if they are 12 years of age and under and are not restrained or improperly restrained. Be- cause children are lighter and weaker than adults, their risk of being injured from deploy- ment is greater. For that reason, we strongly recommend that ALL children (including those in child seats and those that have outgrown child restraint devic-


es) sit in the REAR seat properly restrained at all times in a child restraint device or in a seat- belt, whichever is appropriate for the child’s age, height and weight. Secure ALL types of child restraint devices (in- cluding forward facing child seats) in the REAR seats at all times. According to accident statistics, children are safer when properly restrained in the rear seat- ing positions than in the front seating posi- tions. For instructions and precautions concerning the child restraint system, see the “Child re- straint systems” section in this chapter. (cid:121) NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. (cid:121) Never allow a child to stand up, or to kneel on the front passenger’s seat, or never hold a child on your lap or in your arms. The SRS airbag de- ploys with considerable force and can injure or even kill the child.


Seat, seatbelt and SRS airbags


(cid:121) When the SRS airbag deploys, some smoke will be released. This smoke could cause breathing problems for people with a history of asthma or other breathing trouble. If you or your passengers have breathing problems after SRS airbag deploys, get fresh air promptly. (cid:121) A deploying SRS airbag releases hot gas. Oc- cupants could get burnt if they come into direct contact with the hot gas.


NOTE When you sell your vehicle, we urge you to explain to the buyer that it is equipped with SRS airbags by alerting him to the applicable section in this owner’s manual.


– CONTINUED – 1-55


Seat, seatbelt and SRS airbags


11


10


12


UG1034BB


1-56


1) Airbag control module (including


impact sensors)


2) Airbag module (driver’s side) 3) Airbag module (passenger’s


4) Front sub sensor (left hand side) 5) Front sub sensor (right hand


side)


side)


6) Side airbag module (driver’s


side – if equipped)


7) Side airbag module (passen-


ger’s side – if equipped)


8) Side airbag sensor (driver’s side


– if equipped)


9) Side airbag sensor (passenger’s


side – if equipped)


10) Airbag wiring (yellow) 11) Seatbelt pretensioner (driver’s


12) Seatbelt pretensioner (passen-


side)


ger’s side)


Seat, seatbelt and SRS airbags


SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG.


(cid:132) SRS frontal airbag The driver’s SRS frontal airbag is stowed in the center portion of the steering wheel. The passenger’s SRS frontal airbag is stowed near the top of the dashboard under an “SRS AIRBAG” mark. In a moderate to severe frontal collision, the driver’s and front passenger’s SRS frontal airbags deploy and supplement the seatbelts by reducing the impact on the driver’s and front passenger’s head and chest.


HS1070BA


HG1043BA


Never allow a child to stand up, or to kneel on the front passenger’s seat. The SRS airbag de- ploys with considerable force and can injure or even kill the child.


NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS


– CONTINUED – 1-57


Seat, seatbelt and SRS airbags


HS1069BA


HS1084BA


Never hold a child on your lap or in your arms. The SRS airbag deploys with considerable force and can injure or even kill the child.


The SRS airbag deploys with considerable speed and force. Occupants who are out of proper position when the SRS airbag deploys could suffer very serious injuries. Because the SRS airbag needs enough space for deploy- ment, the driver should always sit upright and well back in the seat as far from the steering wheel as practical while still maintaining full ve- hicle control and the front passenger should move the seat as far back as possible and sit upright and well back in the seat. It is also important to wear your seatbelt to help


1-58


avoid injuries that can result when the SRS air- bag contacts an occupant not in proper posi- tion such as one thrown toward the front of the vehicle during pre-accident braking.


Seat, seatbelt and SRS airbags


UG1514BA


UG1513BA


Do not attach accessories to the windshield, or fit an extra-wide mirror over the rear view mir- ror. If the SRS airbag deploys, those objects could become projectiles that could seriously injure vehicle occupants.


Do not put any objects over the steering wheel pad and dashboard. If the SRS frontal airbag deploys, those objects could interfere with its proper operation and could be propelled inside the vehicle and cause injury.


– CONTINUED – 1-59


Seat, seatbelt and SRS airbags


(cid:84) Operation


A) Driver’s side B) Passenger’s side 1) SRS AIRBAGs deploy as soon as a collision occurs. 2) After deployment, SRS AIRBAGs start to deflate immediately so that the driver’s vision is not obstructed.


HS1087BB


1-60


The SRS airbag can function only when the ignition switch is in the “ON” position. If the front sub sensors inside the both front fenders and the impact sensors in the airbag control module detect a certain predetermined amount of force during a frontal collision, the control module sends signals to the frontal airbag modules instructing them to inflate the SRS frontal airbags. Then both airbag modules produce gas, which instantly inflates driver’s and pas- senger’s SRS frontal airbags. After the deployment, the SRS airbags immediately start to deflate so that the driver’s vision is not obstructed. The time required from detecting impact to the deflation of the SRS air- bag after deployment is shorter than the blink of an eye. The front passenger’s SRS frontal airbag deploys to- gether with driver’s SRS frontal airbag even when no one occupies the front passenger’s seat. Although it is highly unlikely that the SRS airbag would activate in a non-accident situation, should it occur, the SRS airbag will deflate quickly, not obscuring vi- sion and will not interfere with the driver’s ability to maintain control of the vehicle. When the SRS airbag deploys, a sudden, fairly loud inflation noise will be heard and some smoke will be


Seat, seatbelt and SRS airbags


released. These occurrences are normal result of the deployment. This smoke does not indicate a fire in the vehicle.


Do not touch the SRS airbag system compo- nents around the steering wheel and dash- board with bare hands right after deployment. Doing so can cause burns because the compo- nents can be very hot as a result of deployment.


The SRS frontal airbag is designed to deploy in the event of an accident involving a moderate to severe frontal collision. It is basically not designed to deploy in lesser frontal impacts because the necessary pro- tection can be achieved by the seatbelt alone. Also, it is basically not designed to deploy in side or rear im- pacts or in roll-over accidents because deployment of the SRS frontal airbag would not help the occupant in those situations. The SRS airbag is designed to func- tion on a one-time-only basis. SRS airbag deployment depends on the level of force experienced in the passenger compartment during a collision. That level differs from one type of collision to another, and it may have no bearing on the visible – CONTINUED – 1-61


Seat, seatbelt and SRS airbags


damage done to the vehicle itself. (cid:86) When will the SRS frontal airbag most likely de-


ploy?


(cid:86) At what other times might the SRS frontal air-


bag deploy?


HG1045BA


A head-on collision against a thick concrete wall at a vehicle speed of 12 to 19 mph (20 to 30 km/h) or high- er activates the SRS frontal airbag. The SRS frontal airbag will also be activated when the vehicle is ex- posed to a frontal impact similar in fashion and magni- tude to the above-mentioned collision.


1-62


The SRS frontal airbag may be activated when the ve- hicle sustains a hard impact in the undercarriage area from the road surface (such as when the vehicle


HG1046BA


Seat, seatbelt and SRS airbags


plunges into a deep ditch, is severely bumped or knocked hard against an obstacle on the road such as a curb). (cid:86) When is the SRS frontal airbag unlikely to de-


ploy?


There are many types of collisions which might not necessarily require SRS frontal airbag deployment. If the vehicle strikes an object, such as a telephone pole or sign pole, or if it slides under a truck’s load bed, or if it sustains an oblique offset frontal impact, the SRS frontal airbag may not deploy depending on the level of accident forces involved.


UG1083BA


– CONTINUED – 1-63


Seat, seatbelt and SRS airbags


(cid:86) When will the SRS frontal airbag not deploy?


UG1084BA


The SRS frontal airbag is basically not designed to de- ploy if the vehicle is struck from side or from behind, or if it rolls onto its side or roof, or if it is involved in a low- speed frontal collision.


1-64


HS1104BB


1) First impact 2) Second impact In an accident where the vehicle is impacted more than once, the SRS frontal airbag deploys only once. Example: In the case of a double collision, first with an- other vehicle, then against a concrete wall in immedi- ate succession, once the SRS frontal airbag is activat- ed on the first impact, it will not be activated on the second.


(cid:132) SRS side airbag (if equipped) The SRS side airbag is stored in the door side of each front seatback, which bears an “SRS AIRBAG” label. In a moderate to severe side impact collision, the SRS side airbag on the impacted side of the vehicle de- ploys between the occupant and the door panel and supplements the seatbelt by reducing the impact on the occupant’s chest and head.


The SRS side airbag is designed as only a sup- plement to the primary protection provided by the seatbelt. It does not do away with the need to fasten seatbelts. It is also important to wear your seatbelt to help avoid injuries that can re- sult when an occupant is not seated in a proper upright position.


Seat, seatbelt and SRS airbags


HS1092BA


Do not sit or lean unnecessarily close to either front door. The SRS side airbag is stored in both front seat seatbacks next to the door, and it provides protection by deploying rapidly (faster than the blink of an eye) in the event of a side impact collision. However, the force of SRS side airbag deployment may cause injuries if your head or other body parts are too close to the SRS side airbag.


– CONTINUED – 1-65


Seat, seatbelt and SRS airbags


HS1093BA


HS1094BA


Do not rest your arm on either front door or its internal trim. It could be injured in the event of SRS side airbag deployment.


1-66


HS1095BA


Never allow a child to kneel on the front pas- senger’s seat facing the side window or to wrap his/her arms around the front seatback. In the event of an accident, the force of the SRS side airbag deployment could injure the child seri- ously because his/her head or arms or other body parts are too close to the SRS side airbag. Since your vehicle is also equipped with a pas- senger’s SRS frontal airbag, children aged 12
and under should be placed in the rear seat anyway and should be properly restrained at all times.


Seat, seatbelt and SRS airbags


HS1096BA


Do not attach accessories to the door trim or near either SRS side airbags and do not place objects near the SRS side airbags. In the event of the SRS side airbag deployment, they could be propelled dangerously toward the vehicle’s occupants and cause injuries.


– CONTINUED – 1-67


Seat, seatbelt and SRS airbags


UG1534BA


Do not put any kind of cover or clothes or other objects over either front seatback and do not attach labels or stickers to the front seat sur- face on or near the SRS side airbag. They could prevent proper deployment of the SRS side air- bag, reducing protection available to the front seat’s occupant.


1-68


(cid:84) Operation


HS1098BB


A) SRS side airbag deploys as soon as a collision oc-


B) SRS side airbag protects the front passenger’s head


curs.


and chest.


C) After deployment, SRS side airbag starts to deflate im-


mediately.


the deployment. This smoke does not indicate a fire in the vehicle.


Seat, seatbelt and SRS airbags


The SRS side airbag can function only when the igni- tion switch is in the “ON” position. The driver’s and front passenger’s SRS side airbags deploy independently of each other since each has its own impact sensor. Also, the SRS side airbag deploys independently of the frontal airbags in the steering wheel and instrument panel. An impact sensor is incorporated into each of the ve- hicle’s center pillars. If either sensor detects a certain predetermined amount of force during a side impact collision, the control module sends a signal to the side airbag module on the impacted side of the vehicle, in- structing it to inflate the SRS side airbag. Then the side airbag module produces gas, which instantly in- flates the SRS side airbag. After deployment, the SRS side airbag will deflate in a few seconds. The SRS side airbag deploys even when no one occu- pies the seat on the side on which an impact is ap- plied. When the SRS side airbag deploys, a sudden, fairly loud inflation noise will be heard and some smoke will be released. These occurrences are normal result of


Do not touch the SRS side airbag system com- ponents around the front seatback with bare hands right after deployment. Doing so can cause burns because the components can be very hot as a result of deployment.


The SRS side airbag is designed to deploy in the event of an accident involving a moderate to severe side im- pact collision. It is basically not designed to deploy in lesser side impact. Also, it is basically not designed to deploy in frontal or rear impacts because SRS side air- bag deployment would not help the occupant in those situations. Each SRS side airbag is designed to function on a one-time-only basis. SRS side airbag deployment depends on the level of force experienced in the passenger compartment dur- ing a side impact collision. That level differs from one type of collision to another, and it may have no bearing on the visible damage done to the vehicle itself.


– CONTINUED – 1-69


Seat, seatbelt and SRS airbags


(cid:86) When will the SRS side airbag most likely de-


ploy?


A severe side impact near the front seat activates the SRS side airbag.


UG1519BA


1-70


(cid:86) When is the SRS side airbag unlikely to deploy?


Seat, seatbelt and SRS airbags


1) The vehicle is involved in an ob-


lique side-on impact.


2) The vehicle is involved in a side-on impact in an area outside the vicin- ity of the passenger compartment.


3) The vehicle strikes a telephone


pole or similar object.


4) The vehicle is involved in a side-on


impact from a motorcycle.


5) The vehicle rolls onto its side or


roof.


UG1085BB


– CONTINUED – 1-71


Seat, seatbelt and SRS airbags


There are many types of collisions which might not necessarily require SRS side airbag deployment. In the event of accidents like those illustrated, the SRS side airbag may not deploy depending on the level of accident forces involved.


1-72


(cid:86) When will the SRS side airbag not deploy?


1) The vehicle is involved in a frontal collision with anoth-


er vehicle (moving or stationary). 2) The vehicle is struck from behind.


HG1051BB


The SRS side airbag is basically not designed to de- ploy if the vehicle is involved in a frontal collision or is struck from behind. Examples of such accidents are il- lustrated.


vated on the second.


(cid:132) SRS airbag system monitors


Seat, seatbelt and SRS airbags


HS1102BB


UG7020DA


1) First impact 2) Second impact In an accident where the vehicle is struck from the side more than once, the SRS side airbag deploys only once. Example: In the case of a double side impact collision, first with one vehicle and immediately followed by an- other from the same direction, once the SRS side air- bag is activated on the first impact, it will not be acti-


A diagnostic system continually monitors the readi- ness of the SRS airbag system while the vehicle is be- ing driven. The SRS airbag system warning light “AIR- BAG” will show normal system operation by lighting for about 6 seconds when the ignition key is turned to the “ON” position. The following components are monitored by the indi- cator: (cid:121) Front sub sensor (Right hand side) (cid:121) Front sub sensor (Left hand side)


– CONTINUED – 1-73


Seat, seatbelt and SRS airbags


(cid:121) Airbag control module (including impact sensors) (cid:121) Frontal airbag module (Driver’s side) (cid:121) Frontal airbag module (Passenger’s side) (cid:121) Side airbag sensor (Driver’s side – if equipped) (cid:121) Side airbag sensor (Passenger’s side – if equipped) (cid:121) Side airbag module (Driver’s side – if equipped) (cid:121) Side airbag module (Passenger’s side – equipped) (cid:121) Seatbelt pretensioner (Driver’s side) (cid:121) Seatbelt pretensioner (Passenger’s side) (cid:121) All related wiring


if


If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pretensioners and/or SRS airbag sys- tem. Immediately take your vehicle to your nearest SUBARU dealer to have the system checked. Unless checked and properly re- paired, the seatbelt pretensioners and/or SRS airbag will not operate properly in the event of a collision, which may increase the risk of inju- ry. (cid:121) Flashing or flickering of the indicator light (cid:121) No illumination of the warning light when the ignition switch is first turned to the “ON” posi- tion


1-74


(cid:121) Continuous illumination of the warning light (cid:121) Illumination of the warning light while driving


(cid:132) SRS airbag system servicing


(cid:121) When discarding an airbag module or scrap- ping the entire vehicle damaged by a collision, consult your SUBARU dealer. (cid:121) The SRS airbag has no user-serviceable parts. Do not use electrical test equipment on any circuit related to the SRS airbag system. For required servicing of the SRS airbag, see your nearest SUBARU dealer. Tampering with or disconnecting the system’s wiring could re- sult in accidental inflation of the SRS airbag or could make the system inoperative, which may result in serious injury. The wiring harnesses of the SRS airbag system are covered with yellow insulation and system connectors are yellow for easy identification.


If you need service or repair in areas listed be- low, we recommend that you have an autho- rized SUBARU dealer perform the work. The SRS airbag control module, impact sensors and airbag modules are stored in these areas. (cid:121) Under the center console (cid:121) Inside each front fender (cid:121) Steering wheel and column and nearby areas (cid:121) Top of the dashboard on front passenger’s side and nearby areas (cid:121) Each front seat and nearby area (only for ve- hicles with SRS side airbags) (cid:121) Inside each center pillar


In the event that the SRS airbag is deployed, re- placement of the system should be performed only by an authorized SUBARU dealer. When the components of the SRS airbag system are re- placed, use only genuine SUBARU parts. To ensure their long-term reliability, the SRS airbags must be inspected by a SUBARU dealer ten years af- ter the date of manufacture, which is shown on the cer- tification plate attached to the driver’s door jamb.


Seat, seatbelt and SRS airbags


NOTE In the following cases, contact your SUBARU deal- er as soon as possible. (cid:121) The front part of the vehicle was involved in an accident in which the SRS frontal airbags did not deploy. (cid:121) The pad section of the steering wheel or front passenger’s frontal airbag cover is scratched, cracked, or otherwise damaged. In addition, if your vehicle is equipped with SRS side airbags, contact your SUBARU dealer as soon as possible in the following cases. (cid:121) Either center pillar or a nearby area of the vehi- cle was involved in an accident in which the SRS side airbag did not deploy. (cid:121) The fabric or leather of either front seatback is cut, frayed, or otherwise damaged.


(cid:132) Precautions against vehicle modifica-


tion


in serious


(cid:121) To avoid accidental activation of the system or rendering the system inoperative, which may result injury, no modifications – CONTINUED – 1-75


winches, snow plow, skid plate, etc.) other than genuine SUBARU accessory parts to the front end. (cid:121) Modification of the suspension system or front end structure. (cid:121) Installation of a tire of different size and con- struction from the tires specified on the tire placard attached to the driver’s door jamb. (cid:121) Attachment of any equipment (side steps or side sill protectors, etc.) other than genuine SUBARU accessory parts to the side body (for vehicles with side airbags only).


Always consult your SUBARU dealer if you want to in- stall any accessory parts to your vehicle.


Seat, seatbelt and SRS airbags


should be made to any components or wiring of the SRS airbag system. This includes following modifications:


(cid:121) Installation of custom steering wheels (cid:121) Attachment of additional trim materials to the dashboard (cid:121) Installation of custom seats (for vehicles with SRS side airbags only) (cid:121) Replacement of seat fabric or leather (for vehicles with SRS side airbags only) (cid:121) Installation of additional fabric or leather on the front seat (for vehicles with SRS side airbags only)


(cid:121) Installation of additional electrical/electronic equipment such as a mobile two-way radio on or near the SRS airbag system components and/or wiring is not advisable. This could inter- fere with proper operation of the SRS airbag system.


Do not perform any of the following modifica- tions. Such modifications can interfere with proper operation of the SRS airbag system. (cid:121) Attachment of any equipment (brush bar,


1-76


Keys ............................................................... Key number ....................................................... Immobilizer (WRX-STi) ................................. Security ID plate ................................................ Security indicator light ..................................... Key replacement ............................................... Door locks ..................................................... Locking and unlocking from the outside ........ Locking and unlocking from the inside .......... Power door locking switches ...................... Remote keyless entry system ..................... Locking the doors ............................................. Unlocking the doors ......................................... Illuminated entry ............................................... Vehicle finder function ..................................... Sounding a panic alarm ................................... Selecting audible signal operation .................. Replacing the battery ....................................... Replacing lost transmitters .............................. Security system (if equipped) ..................... System operation .............................................. Arming the system ............................................ Disarming the system ....................................... Valet mode ......................................................... Passive arming .................................................. Child safety locks ......................................... Windows ........................................................ Power windows ................................................. Trunk lid (Sedan) ..........................................


2-2
2-3
2-3
2-4
2-5
2-5
2-6
2-6
2-7
2-8
2-9
2-10
2-10
2-11
2-11
2-11
2-11
2-11
2-13
2-17
2-17
2-17
2-19
2-20
2-20
2-23
2-24
2-24
2-27


Keys and doors


To open and close the trunk lid from outside ............................................................ To open the trunk lid from inside .................... To cancel the trunk lid release ........................ Internal trunk lid release handle ......................


2-27
2-28
2-28
2-28
Rear gate (Wagon) ........................................ 2-31
Moonroof (if equipped) ................................. 2-33
2-33
2-33
2-35


Tilt function ....................................................... Sliding function ................................................. Sun shades ........................................................


2-1


Keys and doors


Keys and doorsKeys


WRX-STi 1) Master key (Black) 2) Submaster key (Black) 3) Valet key (Gray) 4) Key number plate 5) Security ID plate


2-2


UG2044BC


HS2011BB


Except WRX-STi 1) Master key 2) Submaster key 3) Valet key 4) Key number plate Three types of keys are provided for your vehicle: Master key, submaster key and valet key. The master key and submaster key fit all locks on your vehicle. (cid:121) Ignition switch (cid:121) Doors (cid:121) Trunk (Sedan) (cid:121) Glove box


The valet key fits only the ignition switch and driver’s door lock. You can keep the trunk and glove box locked when you leave your vehicle and valet key at a parking facility.


Do not attach a large key holder or key case to either key. If it banged against your knees while you were driving, it could turn the ignition switch from the ON position to the ACC or OFF position, thereby stopping the engine.


(cid:132) Key number The key number is stamped on the metal plate at- tached to the key set. Write down the key number and keep it in another safe place, not in the vehicle. This number is needed to make a replacement key if you lose your key or lock it inside the vehicle.


Keys and doors


Immobilizer (WRX-STi) The immobilizer system is designed to prevent an un- authorized person from starting the engine. Only keys registered with your vehicle’s immobilizer system can be used to operate your vehicle. Even if an unregis- tered key fits into the ignition switch and can be turned to the “START” position, the engine will automatically stop after several seconds. Each immobilizer key contains a transponder in which the key’s ID code is stored. When a key is inserted into the ignition switch and turned to the “ON” position, the transponder transmits the key’s ID code to the immo- bilizer system’s receiver. If the transmitted ID code matches the ID code registered in the immobilizer sys- tem, the system allows the engine to be started. Since the ID code is transmitted and acted upon almost in- stantly, the immobilizer system does not impede nor- mal starting of the engine. If the engine fails to start, pull out the key once before trying again. (Refer to the “Ignition switch” section [chapter 3].) NOTE To protect your vehicle from theft, please pay close attention to the following security precau- tions:


– CONTINUED – 2-3


Keys and doors


(cid:121) Never leave your vehicle unattended with its keys inside. (cid:121) Before leaving your vehicle, close all windows and lock the doors and rear gate. (cid:121) Do not leave spare keys or any record of your key number in the vehicle.


(cid:121) Do not place the key under direct sunlight or anywhere it may become hot. (cid:121) Do not get the key wet. If the key gets wet, wipe it dry with a cloth immediately.


(cid:132) Security ID plate


UB2534BB


A) Key number plate B) Security ID plate The security ID is stamped on the metal plate attached to the key set. Write down the security ID and keep it in another safe place, not in the vehicle. This number is needed to make a replacement key if you lose your key or lock it inside the vehicle. This number is also needed for replacement or repair of the engine control unit, immobilizer control unit.


2-4


(cid:132) Security indicator light The security indicator light deters potential thieves by indicating that the vehicle is equipped with an immobi- lizer system. It begins flashing (approximately once every three seconds) about 60 seconds after the igni- tion switch is turned from the “ON” position to the “ACC” or “LOCK” position or immediately after the key is pulled out. If the security indicator light does not flash, the immo- bilizer system may be faulty. If this occurs, we recom- mend that you contact your SUBARU dealer as soon as possible. In case an unauthorized key is used (e.g. an imitation key), the security indicator light comes on. NOTE Even if the security indicator light flashes irregu- larly or its fuse blows (the light does not flash if its fuse is blown), the immobilizer system will func- tion normally.


(cid:132) Key replacement Your key number and security ID will be required if you ever need a replacement key made. Any new key must be registered for use with your vehicle’s immobi- lizer system before it can be used. Up to four keys can


Keys and doors


be registered for use with one vehicle. For security, all the keys registered with your vehicle’s immobilizer system will have their ID codes erased and re-registered when a new key is made. Therefore, all of your vehicle’s keys must be presented when a new key is registered. Any key that is not re-registered when a new key is made cannot be used after the oth- er keys are re-registered. For information on replace- ment keys and on the registration of keys with your im- mobilizer system, we recommend that you contact your SUBARU dealer. NOTE This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Oper- ation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interfer- ence received, including interference that may cause undesired operation. NO USER SERVICEABLE PARTS INSIDE. DO NOT ATTEMPT TO MODIFIED THIS EQUIP- MENT. IF MODIFIED, YOUR AUTHORITY TO OP- ERATE THIS EQUIPMENT MIGHT BE VOIDED BY FCC or Industry Canada.


– CONTINUED – 2-5


Keys and doors


Door locks (cid:132) Locking and unlocking from the out-


side


UG2501BA


To lock the door from the outside with the key, turn the key toward the rear. To unlock the door, turn the key toward the front. Pull the outside door handle to open an unlocked door.


2-6


HS2013EB


1) Rotate the lock lever rearward. 2) Close the door. To lock the door from the outside without the key, ro- tate the lock lever rearward and then close the door. To lock the door from the outside using the power door locking switch, push the front side of the switch (“LOCK” side) and then close the door. In this case, all closed doors and the rear gate (for Wagon) are locked at the same time. Always make sure that all doors and the rear gate (for Wagon) are locked before leaving your vehicle.


NOTE Make sure that you do not leave the key inside the vehicle when locking the doors from the outside without the key.


(cid:132) Locking and unlocking from the inside


is unlocked. Pull the inside door handle to open an unlocked door. Always make sure that all doors and the rear gate (for Wagon) are closed before starting to drive.


Keys and doors


UG2502BB


1) Lock 2) Unlock To lock the door from the inside, rotate the lock lever rearward. To unlock the door from the inside, rotate the lock lever forward. The red mark on the lock lever appears when the door


Keep all doors locked when you drive, especial- ly when small children are in your vehicle. Along with the proper use of seatbelts and child restraints, locking the doors reduces the chance of being thrown out of the vehicle in an accident. It also helps prevent passengers from falling out if a door is accidentally opened, and intrud- ers from unexpectedly opening doors and en- tering your vehicle.


– CONTINUED – 2-7


Keys and doors


Power door locking switches


NOTE Make sure that you do not leave the key inside the vehicle before locking the doors from the outside using power door locking switches.


HS2015BB


1) Lock 2) Unlock All doors and the rear gate (for Wagon) can be locked and unlocked by the power door locking switches lo- cated at the driver’s side and the front passenger’s side doors. To lock the doors, push the front side of the switch. To unlock the doors, push the rear side of the switch. When you close the doors after you set the door locks, the doors remain locked.


2-8


Remote keyless entry system Two transmitters are provided for your vehicle. The remote keyless entry system has the following functions. (cid:121) Locking and unlocking the doors (and rear gate on the Wagon) without a key (cid:121) Sounding a panic alarm (cid:121) Arming and disarming the security system (if your vehicle is equipped with an optional security system). See the next section “Security system (if equipped)” for detailed information. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Oper- ation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The operable distance of the keyless entry system is approximately 30 feet (10 meters). However, this dis- tance will vary depending on environmental condi-


Keys and doors


tions. The system’s operable distance will be shorter in areas near a facility or electronic equipment emitting strong radio waves such as a power plant, broadcast station, TV tower, or remote controller of home elec- tronic appliances. The remote keyless entry system does not operate when the key is inserted in the ignition switch to pre- vent accidental lockout.


(cid:121) Do not expose the transmitter to severe shocks, such as those experienced as a result of dropping or throwing. (cid:121) Do not take the transmitter apart except when replacing the battery. (cid:121) Do not get the transmitter wet. If it gets wet, wipe it dry with a cloth immediately.


– CONTINUED – 2-9


Keys and doors


UG2042BA


: LOCK/ARM button


Press to Lock all doors. Press and Hold to activate panic alarm. Press three times in a five-second period to use vehi- cle finder function. :UNLOCK/DISARM button 1) Press once to Unlock driver’s door. 2) Press a second time to Unlock all other doors (and


rear gate on the Wagon).


(cid:132) Locking the doors Briefly press the “ ” button (for less than two sec- onds) to lock all doors (and rear gate on the Wagon). An electronic chirp will sound once and the turn signal


2-10


lights will flash once. If any of the doors (or the rear gate) is not fully closed, an electronic chirp will sound five times and the turn signal lights will flash five times to alert you that the doors (or the rear gate) are not properly closed. When you close the door, it will automatically lock. NOTE ” button is pressed for two seconds or If the “ longer, the panic alarm will sound. When locking the doors in normal circumstances, press the “ ” button for less than two seconds. For de- tails on the panic alarm, refer to “Sounding a panic alarm”.


(cid:132) Unlocking the doors Briefly press the “ ” button (for less than two sec- onds) to unlock the driver’s door. An electronic chirp will sound twice and the turn signal lights will flash twice. To unlock all other doors (and rear gate on the Wagon), briefly press the “ ” button a second time within 5 seconds. NOTE If the interval between the first and second press- es of the “ ” button (for unlocking of all of the doors and the rear gate) is extremely short, the


system may not respond.


(cid:132) Illuminated entry The interior (dome) light and ignition switch light (for turbo models) will illuminate when the “ ” button is pressed. These lights stay illuminated for approxi- mately 30 seconds if any of the doors (or the rear gate on the Wagon) is not opened. If the “ ” button is pressed before 30 seconds have elapsed, these lights will go out. Also, these lights will go out if the key is inserted in the ignition switch. The interior light switch must be set to the middle position in order for this function to operate.


(cid:132) Vehicle finder function Use this function to find your vehicle parked among many vehicles in a large parking lot. Provided you are within 30 feet (10 meters) of the vehicle, pressing the “ ” button three times in a five-second period will cause your vehicle’s horn to sound once and its turn signal lights to flash three times.


(cid:132) Sounding a panic alarm To activate the alarm, keep the “ for more than two seconds.


” button pressed


Keys and doors


The horn will sound and the turn signal lights will flash. To deactivate it, press the “ ” but- ton. Unless a button on the remote is pressed, the alarm will be deactivated after approximately 30 sec- onds.


” button or “


” and “


(cid:132) Selecting audible signal operation Using an electronic chirp, the system will give you an audible signal when the doors lock and unlock. If de- sired, you may turn the audible signal off. To turn the audible signal off, unlock the door by ” button and then simultaneously pressing the “ depress “ ” buttons for more than two seconds. An electronic chirp will sound twice and the turn signal lights will flash twice to inform you that the audible signal has been turned off. To turn the audible signal on, unlock the door by pressing the “ ” button and then simultaneously depress “ ” buttons for more than two seconds. An electronic chirp will sound once and the turn signal lights will flash once to inform you that the audible signal has been turned on.


” and “


(cid:132) Replacing the battery When the transmitter battery begins to get weak, transmitter range will begin to decrease. Replace the – CONTINUED – 2-11


Keys and doors


battery as soon as possible. To replace the battery:


UG2043BA


2. Remove the old battery from the holder.


UB2209BA


1. Open the transmitter case using a flat-head screw- driver.


2-12


Keys and doors


(cid:121) Do not let dust, oil or water get on or in the transmitter when replacing the battery. (cid:121) Be careful not to damage the printed circuit board in the transmitter when replacing the bat- tery.


UB2210BB


A) Negative (–) side facing up 3. Replace with a new battery (Type CR2025 or equivalent) making sure to install the new battery with the negative (–) side facing up. 4. Reinstall the back half of the transmitter case by snapping it back on. After the battery is replaced, the transmitter must be synchronized with the keyless entry system’s control unit. Press either the “ ” but- ton six times to synchronize the unit.


” or “


(cid:132) Replacing lost transmitters If you lose a transmitter or want to purchase additional transmitters (up to four can be programmed), you should re-program all of your transmitters for security reasons. It is recommended that you have your dealer program all of your transmitters into your system. (cid:84) Programming the transmitters The keyless entry system is equipped with a special code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmit- ter codes. The four transmitter codes may be the same or different.


– CONTINUED – 2-13


Keys and doors


To enter the programming mode:


1. Press “ ” button to disarm the security system. (If your vehicle is equipped with the optional security system.)


UG2042CA


2. Open the driver’s door and sit in the driver’s seat. 3. Close the driver’s door.


HS2019BD


2-14


Keys and doors


To program the transmitters:


1. Open the driver’s door. 2. Close the driver’s door.


HS2019BE


HS2020BB


1) ON 2) LOCK 4. Place the ignition key into the ignition switch and cycle the switch from LOCK to ON ten times within 15
seconds. Be sure to stop at the LOCK position. The horn will sound once to indicate that you are in the transmitter programming mode. NOTE You must finish the next step (opening the driver’s door) within 45 seconds of starting this proce- dures.


– CONTINUED – 2-15


Keys and doors


UG2042BA


3. Press and release any button on the transmitter that you wish to program into the system. The horn will sound twice to indicate that the transmitter has been programmed. Any additional transmitters can also be programmed at this time. Repeat steps 1 through 3 for an additional transmitter. To exit the programming mode: 1. After all of your transmitters are programmed, re- move the key from the ignition switch. The horn will sound three times to indicate that the system has exited the programming mode. 2. Make sure that the keyless entry system properly


2-16


operates by operating each transmitter. (cid:84) Deleting old transmitter codes The control unit of the keyless entry system has four memory locations to store transmitter codes, giving it the ability to operate with up to four transmitters. When you lose a transmitter, the lost transmitter’s code re- mains in the memory. For security reasons, lost trans- mitter codes should be deleted from the memory. To delete old transmitter codes, program four trans- mitter codes into the system. If you have only one cur- rent transmitter, program it four times. If you have two current transmitters, program each one twice. If you have three current transmitters, program two of them once and the third one twice. This process will leave only current transmitter codes in the system’s memo- ry. NOTE Make sure no one else is operating their keyless entry system within range of your vehicle when programming transmitters. If someone else were to operate their remote transmitter while you are programming your transmitters, it is possible that their transmitter code will be programmed into your system, allowing them unauthorized access to your vehicle.


Security system (if equipped) The security system helps to protect your vehicle and valuables from theft. The horn sounds and the turn signal lights flash if someone attempts to break into your vehicle. The starter motor is also interrupted to prevent starting the vehicle without a key. The system can be armed and disarmed with the re- mote transmitter. The system does not operate when the key is inserted into the ignition switch.


(cid:132) System operation The security system will give the following alarm indi- cations when triggered: (cid:121) The turn signal lights will flash and the horn will sound intermittently. In addition, the starter motor will not operate. (cid:121) The alarm automatically resets after 30 seconds; however, the alarm will reactivate if the vehicle is tam- pered with again. The alarm will continue for six times if any sensor continues to be activated. The alarm is triggered by: (cid:121) Opening a door, the rear gate or trunk lid. (cid:121) Application of physical shock to the vehicle (e.g.


Keys and doors


forced entry). Note that there are two alarm levels for shock: warning and alarm. In warning mode, the alarm detects lower level vibrations and triggers 2 warning chirps on the horn and two flashes on the lights as a deterrent to would be vandals. In alarm mode, higher levels of shock are detected and the system will go into full alarm. (cid:121) Ignition switch being turned on while in armed state. NOTE With the valet mode selected, the security system does not operate when the remote transmitter is used for locking and unlocking. The security indi- cator light in the combination meter flashes twice per second to show that the valet mode is select- ed. For details, refer to “Valet mode” in this sec- tion.


(cid:132) Arming the system (cid:84) To arm the system using remote transmitter 1. Close all windows. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood (and the trunk lid) are locked. 5. Close all doors (and the rear gate on the Wagon).


– CONTINUED – 2-17


Keys and doors


1) Press to Arm the system. 2) Press to Disarm the system.


2-18


UG2042BB


UG2030BA


Security indicator light 6. Briefly press the “ ” button (for less than two sec- onds). All doors (and the rear gate on the Wagon) will lock, an electronic chirp will sound once, the turn sig- nal lights will flash once, and the security indicator light will flash as follows: All models except WRX-STi: once every approximate- ly two seconds WRX-STi: twice every approximately two seconds If any of the doors (or the rear gate or the trunk lid) is not fully closed, an electronic chirp sounds five times, the turn signal lights flash five times to alert you that the doors (or the rear gate or the trunk lid) are not


properly closed. When you close the door, the system will automatically arm and doors will automatically lock. (cid:84) To arm the system using power door locking


switches


1. Close all windows. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood (and the trunk lid) are locked. 5. Close the doors (and the rear gate on the Wagon) but leave only the driver’s door or the front passen- ger’s door open.


UG2038BB


Keys and doors


6. Push the front side (“LOCK” side) of the power door locking switch to set the door locks. 7. Close the door. An electronic chirp will sound once, the turn signal lights will flash once and the security in- dicator light will flash as follows: All models except WRX-STi: once every approximate- ly two seconds WRX-STi: twice every approximately two seconds NOTE The system can be armed even if the engine hood and/or the windows are opened. Always make sure that they are fully closed before arming the system.


(cid:132) Disarming the system Briefly press the “ ” button (for less than two sec- onds) on the remote transmitter. The driver’s door will unlock, an electronic chirp will sound twice, the turn signal lights will flash twice and the security indicator light will go off. NOTE (WRX-STi) If your vehicle is equipped with an immobilizer, the immobilizer’s function will cause the security indi- cator light to flash (once every approximately three seconds) even after the system is disarmed.


– CONTINUED – 2-19


Keys and doors


Refer to “Immobilizer (WRX-STi)” in this chapter for further details. To unlock all other doors (and the rear gate on the Wagon), briefly press the “ ” button a second time. (cid:84) Emergency disarming If you cannot disarm the system using the transmitter (i.e. the transmitter is lost, broken or the transmitter battery is too weak), you can disarm the system with- out using the transmitter. To disarm the system: 1. Unlock the door with the key and then open the door. 2. The alarm will sound. 3. Insert the key into the ignition switch and cycle it from the “LOCK” to the “ON” position three (3) times within 5 seconds.


(cid:132) Valet mode When you choose the valet mode, the security system does not operate. In valet mode, the remote transmit- ter is used only for locking and unlocking the doors (and rear gate on the Wagon) and panic activation. To enter the valet mode, open the driver’s door and


2-20


” button depressed for more than two keep the “ seconds. The security indicator light will continue to flash twice per second indicating that the system is in the valet mode. To exit valet mode, open the driver’s door and keep ” button pressed for more than two sec- the “ onds. The indicator will stop flashing. NOTE If the remote transmitter is used to lock or unlock the doors while the valet mode is selected, the turn signal lights do not flash but an electronic chirp is emitted.


(cid:132) Passive arming When passive arming mode has been programmed by the dealer, arming of the system is automatically ac- complished without using the remote transmitter. Note that in this mode, DOORS MUST BE MANUALLY LOCKED. (cid:84) To enter the passive mode Since programming the passive arming mode is a complicated procedure, have it done by your nearest SUBARU dealer.


(cid:84) Arming the system 1. Turn the ignition switch to the “ON” position.


HS2024BC


1) ON 2) LOCK 2. Turn the ignition switch from “ON” to “LOCK” posi- tion and remove the key from the ignition switch.


Keys and doors


HS2013FB


3. Open the doors and get out of the vehicle. 4. Before closing the doors, lock all doors with the in- side door lock levers. 5. Close the doors. The system will automatically arm after one minute. In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door lock switch is used to lock the vehicle, arming will take place immediately regardless of whether or not the passive mode has been selected.


– CONTINUED – 2-21


The indicator light provides the following indications. Flashing once: Any door, the rear gate or the trunk lid has been opened. Flashing three times: The impact sensor in the sys- tem’s unit has been activated. This may indicate that your vehicle has been shocked or tampered with by some outside force and/or unauthorized person. Flashing four times: The ignition switch has been turned on or the battery has been disconnected. NOTE The battery must be reconnected before the indi- cator light will flash. To exit this mode, close the door and turn the ignition switch to the “ON” position.


Keys and doors


In passive mode, the system will automatically activate the alarm but WILL NOT automatically lock the doors. In order to lock the doors you must either lock them as indicated in step 4
above or with the key once they have been closed. Failure to lock the doors manually will result in a higher security risk.


(cid:84) Disarming the system To disarm the system, briefly press the “ on the transmitter. (cid:86) Tripped sensor identification (all models ex-


” button


cept WRX-STi)


If an electronic chirp sounds four times and the turn signal lights flash four times when you disarm the sys- tem, this indicates that the alarm was triggered. The number of times the indicator light flashes indicates what sensor caused the alarm condition. To enter identification mode: 1. Open the driver’s door and leave it open. 2. Turn the ignition switch to the “ON” position twice. (“LOCK” → “ON” → “LOCK” → “ON” → “LOCK”) 3. The indicator light will start flashing.


2-22


Child safety locks


UG2503BB


1) Lock 2) Unlock Each rear door has a child safety lock that prevents the doors from being opened even if the inside door handle is pulled. When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever. The door can only be opened from the outside.


Keys and doors


Always use the child safety lock whenever a child rides in the rear seat. Serious injury could result if a child accidentally opened the door and fell out.


– CONTINUED – 2-23


Keys and doors


Windows (cid:132) Power windows


To avoid serious personal injury caused by en- trapment, you must do the following. (cid:121) When operating the power windows, be ex- tremely careful to prevent anyone’s fingers, arms, neck or head from being caught in the window. (cid:121) Always lock the passengers’ windows using the lock switch when children are riding in the vehicle. (cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the power window.


The power windows operate only when the ignition switch is in the “ON” position.


2-24


(cid:84) Driver’s side switches


UG2045BB


1) Lock switch 2) For driver’s window (with one-touch auto down fea-


ture)


3) For front passenger’s window 4) For rear left window 5) For rear right window All door windows can be controlled by the power win- dow switch cluster at the driver side door.


(cid:86) Operating the driver’s window


HS2027BB


1) Open 2) Automatically open 3) Close To open: Push the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down feature that allows the window to be opened fully without hold- ing the switch. Push the switch down until it clicks and release it, and the window will fully open. To stop the window half- way, pull the switch up lightly.


Keys and doors


To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held. (cid:86) Operating the passengers’ windows


HS2027CA


To open the passengers’ windows, push the appropri- ate switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until it reaches the desired position.


– CONTINUED – 2-25


Keys and doors


(cid:86) Locking the passengers’ windows


cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’ windows cannot be operated with the passengers’ switches.


HS2028BB


1) Lock 2) Unlock To lock the passengers’ windows, push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ windows cannot be opened or closed. (cid:84) Passengers’ side switches To open the window, push the switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until the window reaches the desired position. When the lock switch on the power window switch


2-26


Trunk lid (Sedan)


(cid:132) To open and close the trunk lid from


outside


Keys and doors


(cid:121) To prevent dangerous exhaust gas from en- tering the vehicle, always keep the trunk lid closed while driving. (cid:121) Help prevent young children from locking themselves in the trunk. When leaving the vehi- cle, either close all windows and lock all doors or cancel the inside trunk lid release. Also make certain that the trunk is closed. On hot or sunny days, the temperature in the trunk could quickly become high enough to cause death or serious heat-related injuries in- cluding brain damage, particularly for small children.


UG2047BA


To open the trunk lid from outside, insert the key and turn it clockwise. To close the trunk lid, lightly press the trunk lid down until the latch engages.


– CONTINUED – 2-27


Keys and doors


(cid:132) To open the trunk lid from inside


(cid:132) To cancel the trunk lid release


1) Open Pull the trunk lid release lever upward.


2-28


UG2511BB


UG2048BA


The inside trunk lid release can be cancelled to help prevent unauthorized entry into the trunk. To cancel the trunk lid release, set the lid release cancel lever (located on the inside of the trunk lid, mounted to the trunk lid latch) to the “CANCEL” position. When this lock is in the “CANCEL” position, the trunk can be opened only with the key.


(cid:132) Internal trunk lid release handle The internal trunk lid release handle is a device de- signed to open the trunk lid from inside the trunk. In the event children or adults become locked inside the


trunk, the handle allows them to open the lid. The han- dle is located on the inside of the trunk lid.


UG2031BA


To open the trunk lid from inside the trunk, press the yellow handle downward as indicated by the arrow on the handle. This operation unlocks the trunk lid. Then, push up the lid. The handle is made of material that remains lumines-

Loading...
x