2011 Subaru Forester Owners Manual

Download PDF Manual
gal). It only operates when the ignition switch is in the “ON” position. When this light illuminates, fill the fuel tank immedi- ately. NOTE This light does not turn off unless the tank is replenished up to an internal fuel quantity of approximately 3.7 US gal (14 liters, 3.1 Imp gal). CAUTION Promptly put fuel in the tank when- ever the low fuel warning light illuminates. Engine misfires as a result of an empty tank could cause damage to the engine. Black plate (135,1) Instruments and controls 3-21 & Hill start assist warning light (MT models) While the engine is rotating, if there are any malfunctions in the Hill start assist system, the light will illuminate. WARNING When the Hill start assist warning light illuminates, have the vehicle inspected at an authorized SUBARU dealer. & Door open warning light The door open warning light illuminates if any door or the rear gate is not fully closed. Always make sure this light is out before you start to drive. & All-Wheel Drive warn- ing light (AT models) This light illuminates when All-Wheel Drive is disengaged and the drive me- chanism is switched to Front Wheel Drive for maintenance or similar purposes. It flashes if the vehicle is driven with tires of differing diameters fitted on the wheels – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 3-22 Instruments and controls or with an excessively low air pressure in any of the tires. CAUTION Continuing to drive with the AWD warning light flashing can damage the powertrain. If the AWD warning light starts to flash, promptly park in a safe place and check whether the tires have differing diameters and whether any of the tires has an excessively low inflation pressure. & Automatic headlight beam leveler warning light (models with HID headlights) This light illuminates when the automatic headlight beam leveler does not operate normally. If this light illuminates while driving or does not turn off approximately 3 seconds after turning the ignition switch to the “ON” position, have your vehicle inspected at your SUBARU dealer. & Vehicle Dynamics Control warning light/ Vehicle Dynamics Con- trol operation indicator light ! Vehicle Dynamics Control warning light CAUTION The Vehicle Dynamics Control sys- tem provides its ABS control through the electrical circuit of the ABS system. Accordingly, if the ABS is inoperative, the Vehicle Dynamics Control system becomes unable to provide ABS control. As a result, the Vehicle Dynamics Control system also becomes inoperative, causing the warning light to illuminate. Though both the Vehicle Dynamics Control and ABS systems are inop- erative in this case, the ordinary functions of the brake system are still available. You will be safe while driving with this condition, but drive carefully and have your vehicle checked at a SUBARU dealer as soon as possible. Black plate (136,1) NOTE . If the electrical circuit of the Vehicle Dynamics Control system itself mal- functions, only this particular warning light illuminates. Under these circum- stances, the ABS (Anti-lock Brake System) remains fully operational. . The warning light illuminates when the electronic control system of the ABS/Vehicle Dynamics Control system malfunctions. The Vehicle Dynamics Control system is probably inoperative under any of the following conditions. Have your vehicle checked at a SUBARU dealer immedi- ately. . The warning light does not illuminate when the ignition switch is turned to the “ON” position. . The warning light illuminates while the vehicle is running. NOTE If the warning light behavior is as described in the following examples, the Vehicle Dynamics Control system may be considered to be operating normally. . The warning light illuminates right after the engine is started but turns off immediately, remaining off. . The warning light illuminates after 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 the engine has started and turns off while the vehicle is subsequently being driven. . The warning light illuminates during driving, but it turns off immediately and remains off. ! Vehicle Dynamics Control opera- tion indicator light The indicator light flashes during activa- tion of the skid suppression function and during activation of the traction control function. NOTE . The light may remain illuminated for a short period of time after the engine has been started, especially in cold weather. This does not indicate the existence of a problem. The light should turn off as soon as the engine has warmed up. . The indicator light illuminates when the engine has developed a problem and the CHECK ENGINE warning light/ malfunction indicator lamp is on. The Vehicle Dynamics Control system is probably malfunctioning under the follow- ing condition. Have your vehicle checked at a SUBARU dealer as soon as possible. . The light does not turn off even after the lapse of several minutes (the engine Black plate (137,1) Instruments and controls 3-23 & Security indicator light has warmed up) after started. & Vehicle Dynamics the engine has Control OFF indicator light The light illuminates when the Vehicle Dynamics Control OFF switch is pressed to deactivate the Vehicle Dynamics Con- trol system. The Vehicle Dynamics Control system is probably malfunctioning under any of the following conditions. Have your vehicle checked at a SUBARU dealer immedi- ately. . The light does not illuminate when the ignition switch is turned to the “ON” position. . The light does not turn off even after a period of approximately 2 seconds after the ignition switch has been turned to the “ON” position. Type A Type B The security indicator light deters potential thieves by indicating that the vehicle is – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 3-24 Instruments and controls equipped with an immobilizer system. It begins flashing in the following ways. . Once approximately every 3 sec- onds: – Approximately 60 seconds after the ignition switch is turned from the “ON” position to the “Acc” or “LOCK” posi- tion – Immediately after the ignition key is pulled out . Twice approximately every 2 sec- onds: After the alarm system has been armed to “Arming the for surveillance (Refer system” F2-16.) . Five times approximately every 2 seconds: When the alarm system is ready to be armed. . Other flashing patterns: The alarm system may have been trig- gered by unauthorized intrusion or any impact to to the vehicle body. Refer “Tripped sensor identification” F2-19. If the security indicator light does not flash, the immobilizer system may not be func- tioning properly. this occurs, contact your SUBARU dealer as soon as possible. If Black plate (138,1) & Select lever and gear posi- tion indicator (AT models) Type A In case an unauthorized key is used (e.g., an imitation key), the security indicator light illuminates. NOTE Even if the security indicator light flashes irregularly or its fuse blows (the light does not flash if its fuse is blown), the immobilizer system will function normally. & SPORT mode indicator light (AT models) lever is moved to the When the select manual gate, the SPORT mode is se- lected and the indicator light illuminates. Refer to “SPORT mode” F7-20. Type B This indicator shows the position of the select lever. 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 When the manual mode is selected, the gear position indicator (which shows the current gear selection) and the upshift/ downshift to “Automatic transmission” F7-15. & Turn signal indicator light up. Refer indicator lights These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to “Replacing bulbs” F11-47. & High beam indicator light This light shows that the headlights are in the high beam mode. This indicator light also illuminates when the headlight flasher is operated. & Cruise control indica- tor light This light illuminates when the “CRUISE” main switch is pressed. If you press the main switch button while turning the ignition switch “ON”, the cruise function is deactivated and the control “CRUISE” indicator light flashes. To re- activate the cruise control function, turn the ignition switch back to the “Acc” or “LOCK” position, and then turn it again to the “ON” position. & Cruise control set in- dicator light This light illuminates when vehicle speed has been set. & Front fog light indicator light (if equipped) This indicator light is on while the front fog lights are on. & Headlight indicator light This indicator light illuminates when the headlight switch is placed in the “ ” or “ ” position. Black plate (139,1) Instruments and controls 3-25 Clock The clock shows the time while the ignition switch is in the “Acc” or “ON” position. The time changes by 1 minute each time the “+” button or “−” button is pressed. Pressing the “+” button moves the dis- played time forward, while pressing the “−” button moves the displayed time back. Pressing and holding either button changes the displayed time continuously. – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (140,1) 3-26 Instruments and controls CAUTION Information display For type A combination meter: To ensure safety, do not attempt to set the time while driving, as an accident from inadequate attention to the road could result. NOTE If the battery is disconnected, the time will be erased. After reconnecting the battery, set the correct time. 1) Outside temperature indicator 2) Fuel consumption indicator With the ignition switch in the“ ON” position, the outside temperature and fuel consumption are indicated on the display. 1) Information display switching knob With the ignition switch in the “ON” position, each successive press of the information display switching knob toggles the display in the following sequence. For type B combination meter: The fuel consumption indicator is linked with the odometer/trip meter display on the combination meter, according to the fol- lowing chart. 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (141,1) & Outside temperature indica- tor ! Road surface freeze warning indi- cation Instruments and controls 3-27 Odometer/ Trip meter A trip meter B trip meter Fuel consumption indicator Average fuel consumption corresponding to the A trip meter Average fuel consumption corresponding to the B trip meter Odometer U.S-spec. models: Not indicated Other models: Current fuel consumption 1) U.S.-spec. models 2) Except U.S.-spec. models 1) U.S.-spec. models 2) Except U.S.-spec. models The outside temperature indicator shows the outside temperature in a range from −22 to 1228F (−30 to 508C). The indicator can give a false reading under any of the following conditions: . When there is too much sun. . During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately following a shut- down. . When the actual outside temperature falls outside the specified indicator range. lower, When the outside temperature drops to 378F (38C) or the temperature indication flashes to show that the road surface may be frozen. If the outside temperature drops to 378F (38C) or lower while the display is giving an indication other than the outside temperature, the display switches to the outside temperature indication and flashes for 5 seconds before returning to its original indication. the display is already indicating an If outside temperature of 378F (38C) or lower, the indication does not flash even – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 & Average fuel consumption 3-28 Instruments and controls when the outside temperature drops to 378F (38C) or lower again, unless the outside temperature has increased to 418F (58C) or higher. NOTE The outside temperature indication may differ from the actual outside temperature. The road surface freeze warning indication should be treated only as a guide. Be sure to check the condition of the road surface before driving. & Current fuel consumption (if equipped) 1) U.S.-spec. models 2) Except U.S.-spec. models This indication shows the average rate of fuel consumption since the trip meter was last reset. When either of the trip meter indications is reset, the corresponding average fuel consumption value is also reset. NOTE . The indicated values vary in accor- dance with changes in the vehicle’s running conditions. Also, the indicated values may differ slightly from the actual values and should thus be treated only as a guide. . When either trip meter indication is reset, the average fuel consumption This indication shows the rate of consumption at the present moment. fuel Black plate (142,1) corresponding to that trip meter indica- tion is not shown until the vehicle has subsequently covered a distance of 1 mile (or 1 km). & To turn off fuel consumption indicator display The fuel consumption indicator display can be turned off. To turn off this display, turn the ignition switch to the “LOCK” position and press the “+” button adjacent to the information display for approximately 5 seconds. Then, the information display and the clock display will blink for 3 seconds to notify you that the fuel consumption dis- play has been turned off. To restore the indicator, once again press the “+” button for approximately 5 sec- onds. NOTE . The initial display setting of the fuel consumption indicator of your vehicle has been set to operational at the time of shipment from the factory. . The average fuel consumption is calculated even while the indicator is not displayed. . Even if you turn off the fuel con- sumption indicator, the fuel consump- tion indicator will automatically turn on 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (143,1) Instruments and controls 3-29 a long time with the light control switch set to a position other than “OFF”, the battery may be discharged. when the battery voltage is discon- nected and then reconnected for bat- tery replacement or fuse replacement. Light control switch the position of The light control switch only operates when the ignition key is inserted into the ignition switch. Regardless of the light control switch, the illuminated lights are turned off when the ignition key is removed from the ignition switch. NOTE . Even if the key is removed from the ignition switch, the lights can be illu- minated by operating the light control switch position from “OFF” to “ ” and/or “ . If the driver’s door is opened while the lights are illuminated and the key is removed from the ignition switch, the chirp sound informs the driver that the lights are illuminated. ”. CAUTION . Use of any lights for a long period of time while the engine is not running can cause the battery to discharge. . Before leaving the vehicle, make sure that the light control switch is turned to the “OFF” position. If the vehicle is left unattended for – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (144,1) 3-30 Instruments and controls & Headlights & High/low beam change (dim- mer) & Headlight flasher To turn on the headlights, turn the knob on the end of the turn signal lever. first position Instrument panel lights, front side marker lights and license plate lights are on. illumination, tail second position Headlights, instrument panel illumination, tail front side marker lights, and license plate lights are on. lights, To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indicator light “ ” on the combina- tion meter is also on. To switch back to low beam, pull the lever back to the detent position. To flash the headlights, pull the lever toward you and then release it. The high beam will remain on for as long as you hold the lever. The headlight flasher works even though the light switch is in the “OFF” position. When the headlights are on high beam, the high beam indicator light “ ” on the combination meter also illuminates. CAUTION Do not hold the lever in the flashing position for more than just a few seconds. 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 & Automatic headlight beam leveler (models with HID headlights) The HID headlights generate more light than conventional halogen headlights. Therefore a driver of an oncoming vehicle may experience too much glare when your headlight beam height adjustment is high due to the vehicle carrying heavy load. The automatic headlight beam leveler adjusts the headlight beam height auto- matically and optimally according to the load being carried by the vehicle. & Daytime running light system (if equipped) WARNING The brightness of the illumination of the high beam headlights is reduced by the daytime running light system. The light switch must always be turned to the “ ” position when it is dark outside. The high beam headlights will automati- cally illuminate at reduced brightness when the engine has started, under the following conditions: . The select lever is in a position other than the “P” position (AT models). . The parking brake is fully released. . The light switch is in the “OFF” or “ position. NOTE When the light switch is in the “ ” position, the front side marker lights, tail lights and license plate lights are also illuminated. ” Black plate (145,1) Instruments and controls 3-31 Turn signal lever To activate the right turn signal, push the lever up. To activate the left turn signal turn signal, push the turn signal lever down. When the turn is finished, the lever will return automatically. If the lever does not return after cornering, return the lever to the neutral position by hand. To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction of the turn or lane change. The lever will return automatically to the neutral position when you release it. 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (146,1) 3-32 Instruments and controls Illumination brightness con- trol at all. Front fog light switch (if equipped) The brightness of clock display, audio, air conditioner, information display and instru- illumination dims when the ment panel light switch is in the “ ” positions. You can adjust brightness of the instrument panel illumination for better visibility. ” or “ To brighten, turn the control dial upward. To darken, turn the control dial downward. NOTE is turned fully When the control dial the illumination brightness upward, becomes the maximum and the auto- matic dimming function does not work The front fog lights operate only when the low beam headlights are illuminated. However, the front fog lights turn off when the headlights are switched to high beam. To turn on the front fog lights, turn the front fog light switch on the turn signal lever upward to the “ ” position. To turn off the front fog lights, turn the switch back down to the “OFF” position. 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Wiper and washer WARNING In freezing weather, do not use the windshield washer until the wind- shield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view. CAUTION . Do not operate the washer con- tinuously for more than 10 sec- onds, or when the washer fluid tank is empty. This may cause overheating of the washer motor. Check the washer fluid level frequently, such as at fuel stops. . Do not operate the wipers when the windshield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the wind- shield washer. Type A Type B The indicator light located on the combi- nation meter will illuminate when the front fog lights are on. Black plate (147,1) Instruments and controls 3-33 . In freezing weather, be sure that the wiper blades are not frozen to the windshield or rear window before switching on the wipers. Attempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper mo- tor to burn out. the wiper blades are frozen to the window glass, be sure to operate the defroster, windshield wiper dei- cer (if equipped) or rear window defogger before turning on the wiper. If . If the wipers stop during opera- tion because of ice or some other obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper op- eration. . Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 3-34 Instruments and controls Refer to “Windshield washer fluid” F11-38. Also, when driving the vehicle when there are freezing tempera- tures, use non-freezing type wi- per blades. . Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzine. This will cause deterioration of the wiper blades. NOTE . The wiper operates only when the ignition switch is in the “ON” or “Acc” position. . The front wiper motor is protected against overloads by a circuit breaker. If the motor operates continuously under an unusually heavy load, the circuit breaker may trip to stop the motor temporarily. If this happens, park your vehicle in a safe place, turn off the wiper switch, and wait for approxi- mately 10 minutes. The circuit breaker will reset itself, and the wipers will again operate normally. . Clean your wiper blades and win- dow glass periodically with a washer solution to prevent streaking, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the windshield or rear window. . Grease, wax, insects or other mate- rial on the windshield or the wiper blade results in jerky wiper operation and streaking on the glass. If you cannot remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer sur- face of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with water. . If you cannot eliminate the streaking even after following this procedure, replace the wiper blades with new ones. For replacement instructions, refer to “Replacement of wiper blades” F11-40. Black plate (148,1) & Windshield wiper and washer switches The wiper operates only when the ignition switch is in the “ON” or “Acc” position. ! Windshield wipers OFF: Off : Intermittent LO: Low speed HI: High speed To turn the wipers on, push the wiper control lever down. To turn the wipers off, return the lever to the “OFF” position. 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (149,1) Instruments and controls 3-35 ! Wiper intermittent time control ! Mist (for a single wipe) ! Washer ” When the wiper switch is in the “ position, turn the dial to adjust the operat- ing interval of the wiper. For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever. The operating interval can be adjusted continuously from the shortest interval to the longest. The operating interval can be adjusted in nine steps. To wash the windshield, push the washer button at the end of the wiper control lever. The washer fluid sprays until you release the washer button. The wipers operate while you push the button. – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 the rear wiper will speed is high). When the transmission is shifted into reverse, the rear wiper will switch to continuous operation. When the transmis- sion is shifted to a position other than reverse, return to intermittent operation. ! Washer To wash the rear window while the rear wiper is operating, turn the knob clockwise to the “ fluid sprays until you release the knob. To wash the rear window when the rear wiper is not in use, turn the knob counter- clockwise to the “ ” position. The washer fluid sprays, and 2 seconds later the rear wiper operates. Releasing the knob stops the washer fluid spray, and 3 seconds later the rear wiper stops. ” position. The washer 3-36 Instruments and controls & Rear window wiper and washer switch : Washer (accompanied by wiper operation) ON: Continuous INT: Intermittent OFF: Off : Washer ! Rear wiper To turn the rear wiper on, turn the knob on the end of the wiper control lever upward to the “INT” or “ON” position. To turn the wiper off, return the knob on the end of the lever to the “OFF” position. With the switch turned to the “INT” position, the rear wiper will operate inter- mittently at intervals corresponding to the vehicle speed (longer when the vehicle speed is low; shorter when the vehicle Black plate (150,1) Mirrors Always check that the inside and outside mirrors are properly adjusted before you start driving. & Inside mirror The inside mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position. Push it away for the day position. The night position reduces glare from head- lights. 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 & Auto-dimming mirror/com- pass (if equipped) button, the compass display is toggled on or off. When the compass is on, an illuminated compass reading will appear in the upper right corner of the mirror. Even with the mirror in anti-glare mode, the mirror surface turns bright the transmission is shifted into reverse. This is to ensure good rearward visibility during reversing. ! Photosensors if Left (mirror) button 1) Auto dimming indicator 2) 3) Photosensor 4) Right (compass) button 5) Compass display The auto-dimming mirror has an anti-glare feature which automatically reduces glare coming from headlights of vehicles behind you. It also contains a built-in compass. . By pressing and releasing the left button, the automatic dimming function is toggled on or off. When the automatic dimming function is on, the auto dimming indicator light (green) located on the left button will illuminate. . By pressing and releasing the right The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded. For this reason, use care not to cover the sensors with stickers, or Black plate (151,1) Instruments and controls 3-37 other similar items. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator. ! Compass zone adjustment Compass calibration zones 1. The zone setting is factory preset to Zone 8. Refer to the “Compass calibration zones” map shown above to verify that the compass zone setting is correct for your geographical location. 2. Press and hold the right button for 3 seconds then release, and the word “ZONE” will briefly appear and then the zone number will be displayed. 3. Press the right-hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the correct zone setting for your location is – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 3-38 Instruments and controls displayed. 4. Releasing the button for 3 seconds will exit the zone setting mode. & Auto-dimming mirror/com- pass with HomeLink® (if equipped) ! Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metallic objects or structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the right button for 6 - 7 seconds then release, and the compass will enter the calibration mode. “CAL” and direction will be displayed. 4. Drive slowly in a circle until “CAL” disappears from the display (approxi- mately two to three circles). The compass is now calibrated. 5. Further calibration may be necessary should outside influences cause the mirror to read inaccurately. You will know that this has occurred if your compass begins to read in only limited directions. Should you encounter this situation, return to step one of the above procedure and recali- brate the mirror. LED 1) HomeLink® button 1 2) HomeLink® button 2 3) 4) HomeLink® button 3 5) Sensor 6) Automatic dimming on/off button 7) Compass display button 8) Compass display The auto-dimming mirror has an anti-glare feature which automatically reduces glare coming from headlights of vehicles behind you. It also contains a built-in compass and HomeLink® wireless control system. . By pressing the automatic dimming on/ off button, the automatic dimming function is toggled on or off. When the automatic Black plate (152,1) if dimming function is on, the LED indicator will illuminate. Even with the mirror in the automatic dimming mode, the mirror surface turns bright the transmission is shifted into reverse. This is to ensure good rearward visibility during reversing. . By pressing the compass display but- ton, the compass display is toggled on or off. When the compass is on, an illumi- nated compass reading will appear in the upper right corner of the mirror. When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner the mirror housing and damage the mirror. to enter 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 ! Photosensors ! Compass zone adjustment The mirror has a photosensor attached on both the front and back sides. During nighttime driving, these sensors detect distracting glare from vehicle headlights behind you and automatically dim the mirror to eliminate glare and preserve your vision. For this reason, use care not to cover the sensors with stickers, or other similar items. Periodically wipe the sen- sors clean using a piece of dry soft cotton cloth or an applicator. Compass calibration zones to the “Compass calibration 1. Refer zones” map shown above to verify that the compass zone setting is correct for your geographical location. 2. Press and hold the compass display button for 3 seconds until the zone selection comes up (a number will be displayed in the mirror compass window). 3. Press the compass display button repeatedly until the correct zone setting for your location is displayed. 4. Releasing the button for 5 seconds will exit the zone setting mode. Black plate (153,1) Instruments and controls 3-39 ! Compass calibration If a “C” is displayed in the compass 1. window, the compass needs to be cali- brated. 2. Drive the vehicle in a circle at 5 mph (8 km/h) or less until the display reads a direction. 3. You can also calibrate the compass by driving your vehicle on your everyday routine. The compass will be calibrated once it has tracked a complete circle. 4. To recalibrate your compass, push and hold the compass display button for 9 seconds until a “C” appears in the compass window. 5. Calibrate the compass according to step 2 or step 3. ! HomeLink® Wireless Control Sys- tem The HomeLink® Wireless Control System can be used to activate remote control devices such as gate operators, garage door openers, door locks, home lighting and security systems. There are three HomeLink® buttons on the mirror, each of which can be programmed for operation of one desired device. For details on the device types which can be operated by this system, consult the HomeLink® website at: – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (154,1) 3-40 Instruments and controls www.homelink.com or call 1-800-355- 3515. Note the following information about this system. If your vehicle is equipped with the HomeLink® Wireless Control System, it complies with Part 15 of the Federal Communications Commission Rules in the U.S. and the RSS-210 of Industry Canada in Canada. Its operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause undesired operation. Changes and modifications to this system by anyone other than an authorized service facility could void authorization to use this equipment. HomeLink® and the HomeLink® house are registered trademarks of Johnson Con- trols, Inc. WARNING . W h e n p r o g r a m m i n g t h e HomeLink® Wireless Control Sys- tem, you may be operating a garage door opener or other device. Make sure that people and objects are out of the way of the garage door or other device to prevent potential harm or damage. . Do not use the HomeLink® Wire- less Control System with a gar- age door opener that lacks the safety stop and reverse feature as required by applicable safety standards. A garage door opener which cannot detect an object, signaling the door to stop and reverse, does not meet these safety standards. Using a garage door opener without these fea- tures increases risk of serious injury or death. For more infor- mation, consult the HomeLink® website at www.homelink.com or call 1-800-355-3515. CAUTION When programming the HomeLink® Wireless Control System to operate a garage door opener or an entrance gate, unplug the device’s motor from the outlet during programming to prevent motor burnout. NOTE . After programming your HomeLink® Wireless Control System for the de- sired devices, retain the hand-held transmitters for further programming or device testing in the event of a problem. . It is recommended that you insert a new battery in the hand-held transmit- ter of a device to ensure correct programming. ! Garage door opener programming in the U.S.A. NOTE When programming the HomeLink® Wireless Control System for a garage door opener, it is suggested that you park the vehicle outside the garage. 1. Unplug the motor of the garage door opener from the outlet. NOTE If any of the HomeLink® buttons are already programmed for other devices, skip step 2 because it clears the memory of all three buttons. 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 NOTE Some gate operators and garage door openers may require you to replace this programming step 4 with proce- dures in “Programming for entrance gates and garage door openers in Canada” F3-42. the 5. Hold down both buttons until HomeLink® indicator first flashes, slowly then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapidly flashing light indi- cates successful programming of the new frequency signal.) 6. Press and hold the programmed but- ton and check the HomeLink® indicator light. If the indicator light stays on con- tinuously, your garage door should acti- vate and the programming is completed. light If the indicator light flashes rapidly for 2 seconds and then stays on continuously, your garage door opener may be pro- tected by a rolling code feature. In this case you need to perform the additional steps that are described in “Programming rolling-code-protected garage door open- ers in the U.S.A.” F3-41. 1) HomeLink® button 1 2) HomeLink® button 2 3) HomeLink® button 3 2. Press and hold the two outer HomeLink® buttons (button 1 and button 3) until the indicator light begins to flash (after approximately 20 seconds). Then release both buttons. 3. Hold the end of the garage door opener’s hand-held transmitter between 1 and 3 inches (25 and 76 mm) away from the HomeLink® button you wish to pro- gram. 4. Simultaneously press and hold both the hand-held transmitter button and the desired HomeLink® button. DO NOT re- lease the buttons until step 5 has been completed. Black plate (155,1) Instruments and controls 3-41 ! Programming rolling-code-protected garage door openers in the U.S.A. If your garage door opener has a rolling code feature, program the HomeLink® Wireless Control System for it by following steps 1 through 5 in “Garage door opener programming in the U.S.A.” F3-40. Then continue with the following steps. NOTE The assistance of a second person may make the programming quicker and easier. 1. Locate the training button on the garage door opener motor head unit. The exact location and color of the button may vary by brand of garage door opener. If it is difficult to locate the training button, refer to your garage door opener’s instruc- – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 3-42 Instruments and controls tion manual. 1) Training button 2. Press the training button on the garage door opener motor head unit (which activates the “training light” on the unit). Proceed to step 3 within 30 seconds. 3. Inside the vehicle, firmly press, hold for 2 seconds and release the HomeLink® button that was programmed in the pre- vious section. Press and release the button a second time to complete the programming procedure. NOTE Some garage door openers may re- quire you to do the above press-hold- release sequence a third time to com- plete the programming. 4. The garage door opener should now recognize the HomeLink® Wireless Control System and your garage door opener should activate when the HomeLink® button is pressed. ! Programming for entrance gates and garage door openers in Canada 1. Unplug the motor of the entrance gate or garage door opener from the outlet. NOTE If any of the HomeLink® buttons are already programmed for other devices, skip step 2 because it clears the memory of all three buttons. Black plate (156,1) 1) HomeLink® button 1 2) HomeLink® button 2 3) HomeLink® button 3 the HomeLink® indicator 2. Press and hold the two outer HomeLink® buttons (button 1 and button 3) until light begins to flash (after approximately 20 seconds). Then release both buttons. 3. Hold the end of the entrance gate’s/ garage door opener’s hand-held transmit- ter between 1 and 3 inches (25 and 76 mm) away from the HomeLink® button you wish to program. 4. Press and hold the desired HomeLink® button. 5. Press and release (“cycle”) the hand- held transmitter button every 2 seconds until step 6 is complete. 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 6. When the indicator light flashes slowly and then rapidly after several seconds, release both buttons. 7. Plug the motor of the entrance gate/ garage door opener to the outlet. 8. Test your entrance gate/garage door opener by pressing the programmed HomeLink® button. ! Operating the HomeLink® Wireless Control System Once programmed, the HomeLink® Wire- less Control System can be used to remote-control the devices to which its buttons are programmed. To activate a device, simply press the appropriate but- ton. The indicator light illuminates, indicat- ing that the signal is being transmitted. ! Programming other devices To program other devices such as door locks, home lighting and security systems, contact HomeLink® at www.homelink.com or call 1-800-355-3515. ! Reprogramming a single HomeLink® button 1. Press and hold the HomeLink® button you wish to reprogram. DO NOT release the button until step 4 has been com- pleted. 2. When the HomeLink® indicator light begins to flash slowly (after approximately 20 seconds), position the hand-held trans- mitter of the device between 1 to 3 inches (25 to 76 mm) away from the HomeLink® button you wish to program. 3. Press and hold the hand-held trans- mitter button. The HomeLink® indicator light will flash, first slowly and then rapidly. 4. When the indicator light begins to flash rapidly, release both buttons. The programming for the previous device is now erased and the new device can be operated by pressing the HomeLink® button. ! Erasing HomeLink® button memory NOTE . Performing this procedure erases the memory of all the preprogrammed buttons simultaneously. The memory of individual buttons cannot be erased. . It is recommended that upon the sale of the vehicle, the memory of all programmed HomeLink® buttons be erased for security purposes. Black plate (157,1) Instruments and controls 3-43 1) HomeLink® button 1 2) HomeLink® button 2 3) HomeLink® button 3 1. Press and hold the two outer buttons (button 1 and button 3) until the indicator light begins to flash (after approximately 20 seconds). 2. Release both buttons. ! In case a problem occurs If you cannot activate a device using the corresponding HomeLink® button after programming, contact HomeLink® at www.homelink.com or call 1-800-355- 3515 for assistance. – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 3-44 Instruments and controls & Outside mirrors ! Remote control mirror switch the selection when the ignition switch is in the “ON” or “Acc” position. 1. Press either end of switch, “L” for the left, “R” for the right. 2. Move the direction control switch in the direction you want to move the mirror. 3. Return the selection switch to the neutral position to prevent unintentional operation. The mirrors can also be adjusted manu- ally. ! Power folding mirror switch (if equipped) 1) Selection switch 2) Direction control switch The remote control mirrors operate only The power folding mirror switch operates only when the ignition switch is in the “ON” or “Acc” position. To fold the outside mirrors, push the power folding mirror switch. To unfold the mirrors, Black plate (158,1) push the switch again. NOTE . When the temperature is low, the outside mirrors may stop during opera- tion. Push the switch again. When the outside mirrors do not work by switch operation, move them several times by manually. This makes it possible to operate them by switch operation. . When you operate the power folding mirror switch continuously, it may not work. This is not a malfunction. Oper- ate after waiting for a short period of time. . When you unfold the outside mirrors manually, the mirrors may become wobbly. Be sure to unfold the mirrors by switch operation. the outside mirrors are still wobbly, fold the mirrors again and then unfold them by switch operation. If 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (159,1) Instruments and controls 3-45 Defogger and deicer window defogger. For some models, the outside mirror defogger and/or windshield wiper deicer are/is also equipped. The defogger and deicer system is activated only when the ignition switch is in the “ON” position. Automatic climate control system (type A) Manual climate control system 1) Rear window defogger 2) Outside mirror defogger (if equipped) 3) Windshield wiper deicer (if equipped) The vehicle is equipped with a rear Automatic climate control system (type B) To activate the defogger and deicer system, push the control switch that is located on the climate control panel. The rear window defogger, outside mirror – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 3-46 Instruments and controls defogger and windshield wiper deicer are activated simultaneously. The indicator light on the control switch illuminates while the defogger and deicer system is acti- vated. To turn them off, push the control switch again. They also turn off when the ignition switch is turned to the “Acc” or “LOCK” position. The defogger and deicer system will automatically shut off after approximately 15 minutes. If the rear window and the outside mirrors have been cleared and the windshield wiper blades have been deiced completely before that time, push the control switch to turn them off. If defrost- ing, defogging or deicing is not complete, you have to push the control switch to turn them on again. For models with the automatic climate control system, it is possible to set the defogger and deicer system for the con- tinuous operation mode as follows. . Models with genuine SUBARU navi- gation system: The settings can be changed for the continuous operation mode using the navigation monitor. For details, refer to the Owner’s Manual supplement for the navigation system. The settings can also be changed by a SUBARU dealer. Contact your SUBARU dealer for details. . Models without genuine SUBARU navigation system: The settings can be changed by a SUBARU dealer. Contact your SUBARU dealer for details. CAUTION . To prevent the battery from being discharged, do not operate the defogger and deicer system con- tinuously for any longer than necessary. . Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the rear window. They may damage the conductors printed on the window. NOTE . Turn on the defogger and deicer system if the wipers are frozen to the windshield. . If the windshield is covered with snow, remove the snow so that the windshield wiper deicer works effec- tively. Black plate (160,1) . While the defogger and deicer sys- tem is in the continuous operation mode, if the vehicle speed remains at 9 mph (15 km/h) or less for 15 minutes, the windshield wiper deicer automati- cally stops operating, though the rear window defogger and outside mirror defogger maintain continuous opera- tion in this condition. . While the defogger and deicer sys- tem is in the continuous operation mode, the battery voltage drops below the permissible level, continu- ous operation of the defogger and deicer system is canceled and the system stops operating. if 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (161,1) Instruments and controls 3-47 Tilt/telescopic steering wheel Horn WARNING . Do not adjust the steering wheel tilt/telescopic position while driv- ing. This may cause loss of vehicle control and result in personal injury. . If the lever cannot be raised to the the fixed position, adjust steering wheel again. It is dan- gerous to drive without locking the steering wheel. This may cause loss of vehicle control and result in personal injury. 1) 2) Tilt adjustment Telescopic adjustment (if equipped) to the seat position. Refer 1. Adjust “Front seats” F1-2. 2. Pull the tilt/telescopic lock lever down. 3. Move the steering wheel to the desired level. 4. Pull the lever up to lock the steering wheel in place. 5. Make sure that the steering wheel is securely locked by moving it up and down, and forward and backward. To sound the horn, push the horn pad. 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (2,1) — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Left Page Model "ALL_MODEL_MEMO" EDITED: 2007/ 6/ 22 Black plate (7,1) Climate control Ventilator.............................................................. Airflow selection ................................................. Center and side ventilators.................................. Manual climate control system (if equipped) ..................................................... Control panel ...................................................... Heater operation ................................................. Air conditioner operation..................................... 4-2 4-2 4-3 4-3 4-3 4-5 4-7 Automatic climate control system 4-8 (if equipped) ..................................................... Type A ................................................................ 4-8 Type B ............................................................... 4-13 Temperature sensors.......................................... 4-17 Operating tips for heater and air conditioner ...................................................... Cleaning ventilation grille................................... Efficient cooling after parking in direct sunlight ........................................................... Lubrication oil circulation in the refrigerant circuit.............................................................. Checking air conditioning system before summer season ............................................................ Cooling and dehumidifying in high humidity and low temperature weather conditions ................. Air conditioner compressor shut-off when engine is heavily loaded.............................................. Refrigerant for your climate control system ........ Air filtration system ........................................... Replacing an air filter......................................... 4-17 4-17 4-17 4-18 4-18 4-18 4-18 4-18 4-18 4-19 北米Model "A8160BE-B" EDITED: 2010/ 9/ 14 Black plate (164,1) 4-2 Climate control Ventilator & Airflow selection 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 & Center and side ventilators ! Center ventilators ! Side ventilators Move the tab to adjust the flow direction. 1) Open 2) Close 3) Thumb-wheel Move the tab to adjust the flow direction. To open or close the ventilator, turn the thumb-wheel up or down. Black plate (165,1) Climate control 4-3 Manual climate control sys- tem (if equipped) & Control panel Temperature control dial Fan speed control dial 1) 2) 3) Airflow control dial 4) Control switch of the defogger and deicer system (Refer to “Defogger and deicer” F3-45.) 5) Air conditioner button 6) Air inlet selection button ! Temperature control dial This dial regulates the temperature of airflow from the air outlets over a range from the blue side (cool) to red side (warm). – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 4-4 Climate control ! Fan speed control dial The fan operates only when the ignition switch is turned to the “ON” position. The fan speed control dial is used to select four fan speeds. ! Airflow control dial Each dial position activates the following air outlets. (Ventilation): Instrument panel outlets (Bi-level): Instrument panel outlets and foot outlets (Heat): Foot outlets, both side outlets of the instrument panel and some through windshield defroster outlets (A small amount of air flows to the windshield and both side windows to prevent fogging.) (Heat-def): Windshield defroster out- lets, foot outlets and both side outlets of the instrument panel : Windshield defroster outlets and both side outlets of the instrument panel For details, refer to “Airflow selection” F4- 2. NOTE When the dial is placed in the “ ” or “ ” position, the air conditioner com- pressor operates automatically regard- less of the position of the air condi- tioner button to defog the windshield more quickly. However the indicator on the air conditioner button will not illuminate. At the same time, the air inlet selection is automatically set to “outside air” mode. In this state, you cannot select “recir- culation” mode by manually pressing the air inlet selection button. Also, you cannot stop the air condi- tioner compressor by pressing the air conditioner button. ! Air conditioner button The air conditioner operates only when the engine is running. Push the air conditioner button while the fan is in operation to turn on the air Black plate (166,1) conditioner. The indicator light will nate. illumi- Push it again to turn off the air conditioner. ! Air inlet selection button ON position (Recirculation): Interior air is recirculated inside the vehicle. Push the air inlet selection button to the ON posi- tion. The indicator light will illuminate. Place the air inlet selection button to the ON position for fast cooling with the air conditioner or when driving on a dusty road. OFF position (Outside air): Outside air is drawn into the passenger compartment. Push the air inlet selection button again to the OFF position. The indicator light will turn off. 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (167,1) Climate control 4-5 ! Heating and defrosting Place the air inlet selection button to the OFF position when the interior has cooled to a comfortable temperature and the road is no longer dusty. corresponding thumb wheel down. ! Defrosting or defogging the wind- shield WARNING Continued operation with the air inlet selection button in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears. & Heater operation NOTE . Models with air conditioner system: When the “ ” or “ ” position is selected, the air conditioner compres- sor automatically operates regardless of the position of the air conditioner button to defog the windshield more quickly. At the same time, the air inlet selection is automatically switched to the OFF position (outside air). How- ever, the air conditioner indicator light does not illuminate at this time. . When defrosting, defogging or heat- ing, warm air is also emitted from the right and left air outlets. To stop warm airflow from these outlets, turn the To direct warm air to the windshield and front door windows: 1. Set the airflow control dial to the “ position. 2. Turn the temperature control dial all the way to the right. 3. Set the fan speed control dial to the highest speed. ” To direct warm air toward the floor and the windshield: 1. Set the airflow control dial to the “ position. 2. Set the temperature control dial to the most comfortable level. 3. Set the fan speed control dial to the desired speed. ” – CONTINUED – 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (168,1) 4-6 Climate control ! Heating ! Bi-level heating outlets and the air from the foot outlets. ! Ventilation To direct warm air toward the floor: 1. Set the air inlet selection button to the OFF position. 2. Set the airflow control dial to the “ position. 3. Set the temperature control dial to the most comfortable level. 4. Set the fan speed control dial to the desired speed. ” This setting allows you to direct air of different temperatures from the instrument panel and foot outlets. The air from the foot outlets is slightly warmer than from the instrument panel outlets. 1. Set the air inlet selection button to the OFF position. 2. Set the airflow control dial to the “ position. 3. Set the temperature control dial to the desired temperature level. 4. Set the fan speed control dial to the desired speed. ” Setting the temperature control dial fully turned to the red area or blue area decreases the temperature difference between the air from the instrument panel To force outside air through the instrument panel outlets: 1. Set the air inlet selection button to the OFF position. 2. Set the airflow control dial to the “ position. 3. Set the temperature control dial all the way left. 4. Set the fan speed control dial to the desired speed. ” When driving on a dusty road, set the air inlet selection button to the “ON” position. 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 Black plate (169,1) Climate control 4-7 highest speed. The air conditioner compressor automati- cally operates when the airflow control dial is set in the “ ” position to provide better defogging performance. ” or “ WARNING Continued operation with the air inlet selection button in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears. & Air conditioner operation ! Cooling or dehumidifying ” OFF position. 2. Set the airflow control dial to the “ position. 3. Set the air conditioner button to the “ON” position. 4. Set the temperature control dial to the blue side. 5. Set the fan speed control dial at the highest speed. ! Defrosting or defogging 1) ON position For cooling and dehumidification of the passenger compartment, performing the following steps will allow air to flow through the instrument panel outlets: 1. Set the air inlet selection button to the To direct warm air to the windshield and front door windows: 1. Set the airflow control dial to the “ position. 2. Set the temperature control dial to the red side. 3. Set the fan speed control dial at the ” 北米Model "A8160BE-B" EDITED: 2010/ 10/ 14 4-8 Climate control Automatic climate control system (if equipped) NOTE Operate the automatic climate control system when the engine is running.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2011 Subaru Forester Owners Manual