2009 Subaru Forester Owners Manual

the mats to make sure the area is dry. Keep your garage dry. Do not park your vehicle in a damp, poorly ventilated garage. In such a garage, corrosion can be caused by dampness. If you wash the vehicle in the garage or put the vehicle into the garage when wet or covered with snow, that can cause dampness.

If your vehicle is operated in cold weather and/or in areas where road salts and other corrosive materials are used, the door hinges and locks, and hood latch should be inspected and lubricated periodically.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Cleaning the interior

Use a soft, damp cloth to clean the climate control panel, audio equipment, instru- ment panel, center console, combination meter panel, and switches. (Do not use organic solvents.)

& Seat fabric Remove loose dirt, dust or debris with a vacuum cleaner. If the dirt is caked on the fabric or hard to remove with a vacuum cleaner, use a soft brush then vacuum it. Wipe the fabric surface with a tightly wrung cloth and dry the seat fabric thoroughly. If the fabric is still dirty, wipe using a solution of mild soap and luke- warm water then dry thoroughly.

the stain does not come out,

try a If commercially-available fabric cleaner. Use the cleaner on a hidden place and make sure it does not affect the fabric adversely. Use the cleaner according to its instruc- tions. NOTE When cleaning the seat, do not use benzine, paint thinner, or any similar materials.

& Leather seat materials The leather used by SUBARU is a high quality natural product which will retain its distinctive appearance and feel for many years with proper care. Allowing dust or road dirt to build up on the surface can cause the material to become brittle and to wear prematurely. Regular cleaning with a soft, moist, natural fiber cloth should be performed monthly, taking care not to soak the leather or allow water to penetrate the stitched seams. A mild detergent suitable for cleaning woolen fabrics may be used to remove difficult dirt spots, rubbing with a soft, dry cloth afterwards to restore the luster. If your SUBARU is to be parked for a long time in bright sunlight, it is recommended that the seats and headrests be covered, or the windows shaded, to prevent fading or shrinkage. Minor surface blemishes or bald patches may be treated with a commercial leather spray lacquer. You will discover that each leather seat section will develop soft folds or wrinkles, which is characteristic of genuine leather.

Black plate (297,1)

Appearance care 10-5

& Synthetic leather upholstery The synthetic leather material used on the SUBARU may be cleaned using mild soap or detergent and water, after first vacuum- ing or brushing away loose dirt. Allow the soap to soak in for a few minutes and wipe off with a clean, damp cloth. Commercial foam-type cleaners suitable for synthetic leather materials may be used when necessary. NOTE Strong cleaning agents such as sol- vents, paint thinners, window cleaner or gasoline must never be used on leather or synthetic interior materials.

& Climate control panel, audio

panel, instrument panel, console panel, and switches Use a soft, damp cloth to clean the climate control panel, audio equipment, instru- ment panel, center console, combination meter panel, and switches. NOTE Do not use organic solvents such as paint thinners or gasoline, or strong cleaning agents that contain those solvents.

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

10

10-6 Appearance care

& Navigation monitor (if

equipped)

To clean the navigation monitor, wipe it with a silicone cloth or with a soft cloth. If the navigation monitor is extremely dirty, clean it with a soft cloth moistened with neutral detergent then carefully wipe off any remaining detergent. NOTE . Do not spray neutral detergent di- rectly onto the monitor. Doing so could damage the monitor’s components. . Do not wipe the monitor with a hard cloth. Doing so could scratch the monitor. . Do not use cleaning fluid that con- tains thinner, gasoline, or any other volatile substance. Such cleaning fluid could erase the lettering on the switches at the bottom of the monitor.

Black plate (298,1)

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Maintenance schedule ....................................... 11-3
Maintenance precautions................................... 11-3

Before checking or servicing in the engine

11-4

compartment.................................................... When you do checking or servicing in the engine compartment while the engine is running..........

Non-turbo models .............................................. Turbo models .....................................................

11-4
Engine hood ....................................................... 11-5
Engine compartment overview.......................... 11-6
11-6
11-7
Engine oil............................................................ 11-8
11-8
11-9
11-11

Checking the oil level ......................................... Changing the oil and oil filter.............................. Recommended grade and viscosity .................. Recommended grade and viscosity under severe driving conditions .......................................... Synthetic oil.....................................................

11-12
11-12
Cooling system ................................................ 11-12
11-12
11-13
Air cleaner element .......................................... 11-15
11-16
Spark plugs ...................................................... 11-18
11-18
Drive belts ........................................................ 11-18
Manual transmission oil .................................. 11-19
11-19
11-20
Automatic transmission fluid .......................... 11-20
11-20

Cooling fan, hose and connections................... Engine coolant .................................................

Checking the oil level ....................................... Recommended grade and viscosity ..................

Replacing the air cleaner element .....................

Recommended spark plugs ..............................

Checking the fluid level ....................................

Black plate (21,1)

Maintenance and service

Recommended fluid ......................................... Front differential gear oil (AT vehicles).......... Checking the oil level ...................................... Recommended grade and viscosity .................. Rear differential gear oil.................................. Checking the gear oil level............................... Recommended grade and viscosity .................. Power steering fluid ........................................ Checking the fluid level.................................... Recommended fluid ......................................... Brake fluid........................................................ Checking the fluid level.................................... Recommended brake fluid ............................... Clutch fluid (MT vehicles) ............................... Checking the fluid level.................................... Recommended clutch fluid............................... Brake booster .................................................. Brake pedal ...................................................... Checking the brake pedal free play .................. Checking the brake pedal reserve distance....... Clutch pedal (MT vehicles).............................. Checking the clutch function............................ Checking the clutch pedal free play.................. Hill start assist system (MT vehicles) ............ Replacement of brake pad and lining ............ Breaking-in of new brake pads and linings ....... Parking brake stroke ....................................... Tires and wheels.............................................. Types of tires...................................................

11-21
11-21
11-21
11-22
11-22
11-22
11-23
11-24
11-24
11-25
11-25
11-25
11-26
11-26
11-26
11-27
11-27
11-28
11-28
11-28
11-28
11-28
11-29
11-29
11-29
11-30
11-30
11-31
11-31

11

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Maintenance and service

Tire pressure monitoring system (TPMS)

(U.S.-spec. models) ........................................ Tire inspection ................................................. Tire pressures and wear ................................... Wheel balance.................................................. Wear indicators ................................................ Tire rotation direction mark .............................. Tire rotation ..................................................... Tire replacement .............................................. Wheel replacement...........................................

11-31
11-33
11-33
11-35
11-35
11-36
11-36
11-37
11-37
Aluminum wheels............................................. 11-38
Windshield washer fluid .................................. 11-38
Replacement of wiper blades.......................... 11-39
11-40
11-40
11-41
11-41

Windshield wiper blade assembly ..................... Windshield wiper blade rubber ......................... Rear window wiper blade assembly .................. Rear window wiper blade rubber.......................

Black plate (22,1)

Battery .............................................................. Fuses ................................................................ Main fuse.......................................................... Installation of accessories .............................. Replacing bulbs ............................................... Headlights (vehicles with HID headlights) ......... Headlights (vehicles without HID

headlights) .................................................... Position light ................................................... Front turn signal light ...................................... Rear combination lights ................................... License plate light ........................................... Dome light, map light, cargo area light and door step light ....................................................... Other bulbs .....................................................

11-43
11-44
11-45
11-45
11-46
11-47

11-48
11-50
11-50
11-50
11-51

11-51
11-52

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Maintenance schedule

Maintenance precautions

The scheduled maintenance items re- quired to be serviced at regular intervals are shown in the “Warranty and Main- tenance Booklet”.

For details of your maintenance schedule, read the separate “Warranty and Main- tenance Booklet”.

When maintenance and service are re- quired, it is recommended that all work be done by an authorized SUBARU dealer.

If you perform maintenance and service by yourself, you should familiarize yourself with the information provided in this section on general maintenance and service for your SUBARU.

Incorrect or incomplete service could cause improper or unsafe vehicle opera- tion. Any problems caused by improper maintenance and service performed by you are not eligible for warranty coverage.

WARNING

. Testing of an All-Wheel Drive vehicle must NEVER be per- formed on a single two-wheel dynamometer or similar appara- tus. Attempting to do so will result in transmission damage and in uncontrolled vehicle movement and may cause an accident or injuries to persons nearby.

. Always select a safe area when performing maintenance on your vehicle.

Black plate (301,1)

Maintenance and service 11-3

. Always be very careful to avoid injury when working on the vehi- cle. Remember that some of the materials in the vehicle may be hazardous if improperly used or handled, for example, battery acid.

. Your vehicle should only be ser- viced by persons fully competent to do so. Serious personal injury may result to persons not experi- enced in servicing vehicles.

. Always use the proper tools and make certain that they are well maintained.

. Never get under the vehicle sup- ported only by a jack. Always use safety stands to support the vehicle.

. Never keep the engine running in a poorly ventilated area, such as a garage or other closed areas.

. Do not smoke or allow open flames around the fuel or battery. This will cause a fire.

. Because the fuel system is under pressure, replacement of the fuel filter should be performed only by your SUBARU dealer.

. Wear adequate eye protection to

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

11

11-4 Maintenance and service

in your eyes,

guard against getting oil or fluids in your eyes. If something does get thoroughly wash them out with clean water. . Do not tamper with the wiring of the SRS airbag system or seat- belt pretensioner system, or at- tempt to take its connectors apart, as that may activate the system or it can render it inop- erative. The wiring and connec- tors of these systems are yellow for easy identification. NEVER use a circuit tester for this wiring. If your SRS airbag or seatbelt pretensioner needs service, con- sult your nearest SUBARU deal- er.

& Before checking or servicing

in the engine compartment

WARNING

. Always stop the engine and set the parking brake firmly to pre- vent the vehicle from moving.

. Always let the engine cool down. Engine parts become very hot when the engine is running and remain hot for some time after the engine is stopped.

. Do not spill engine oil, engine coolant, brake fluid or any other fluid on hot engine components. This may cause a fire.

. Always remove the key from the ignition switch. When the ignition switch is in the “ON” position, the cooling fan may operate suddenly even when the engine is stopped.

. Before performing any servicing on a vehicle equipped with a remote engine start system (a dealer option) temporarily place that system in the service mode to prevent it from unexpectedly starting the engine.

Black plate (302,1)

& When you do checking or

servicing in the engine com- partment while the engine is running

WARNING

A running engine can be dangerous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any other moving engine parts. Removing rings, watches and ties is advisable.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Engine hood

To open the hood: 1. If the wiper blades are lifted off the windshield, return them to their original position.

2. Pull the hood release knob under the instrument panel.

Black plate (303,1)

Maintenance and service 11-5

WARNING

Always check that the hood is properly locked before you start driving. If it is not, it might fly open while the vehicle is moving and block your view, which may cause an accident and serious bodily in- jury.

3. Release the secondary hood release by moving the lever between the front grille and the hood toward the left. 4. Lift up the hood.

To close the hood: 1. Lower the hood to a height of approxi- mately 5.9 in (15 cm) above its closed position and then let it drop. 2. After closing the hood, be sure the hood is securely locked.

If this does not close the hood, release it from a slightly higher position. Do not push the hood forcibly to close it. It could deform the metal.

11

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

11-6 Maintenance and service

Engine compartment overview & Non-turbo models

Black plate (304,1)

1) Power steering fluid reservoir (page 11-

24)

2) Manual transmission oil level gauge (MT) (page 11-19) or Differential gear oil level gauge (AT) (page 11-21)

3) Clutch fluid reservoir (page 11-26) 4) Automatic transmission fluid level gauge

(page 11-20)

Fuse box (page 11-44)

5) Brake fluid reservoir (page 11-25) 6) 7) Battery (page 11-43) 8) Windshield washer tank (page 11-38) 9) Engine oil filler cap (page 11-8) 10) Engine coolant reservoir (page 11-13) 11) Radiator cap (page 11-13) 12) Engine oil level gauge (page 11-8) 13) Air cleaner element (page 11-15)

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

& Turbo models

Black plate (305,1)

Maintenance and service 11-7

1) Power steering fluid reservoir

(page 11-24)

2) Manual transmission oil level gauge (MT) (page 11-19) or differential gear oil level gauge (AT) (page 11-21)

3) Clutch fluid reservoir (page 11-26) 4) Automatic transmission fluid level gauge

(page 11-20)

Fuse box (page 11-44)

5) Brake fluid reservoir (page 11-25) 6) 7) Battery (page 11-43) 8) Windshield washer tank (page 11-38) 9) Engine oil filler cap (page 11-8) 10) Engine coolant reservoir (page 11-13) 11) Engine oil level gauge (page 11-8) 12) Radiator cap (page 11-13) 13) Air cleaner element (page 11-15)

11

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

11-8 Maintenance and service

Engine oil

NOTE . The engine oil consumption rate is not stabilized, and therefore cannot be determined until the vehicle has tra- veled at least several thousand miles (kilometers). Even after break-in, when the vehicle is used under severe driv- ing conditions such as those men- tioned in the Warranty and Mainte- nance Booklet, engine oil is consumed or deteriorated more quickly than un- der normal driving conditions. If you drive your vehicle under these severe conditions, you should check the oil level at least at every second fuel fill-up time, and change the oil more fre- quently. Please refer to the Warranty and Maintenance Booklet for more de- tails. . If the oil consumption rate seems abnormally high after the break-in period, for example more than 1 quart per 1,200 miles or 1 liter per 2,000
kilometers, contact your SUBARU deal- er.

& Checking the oil level Check the engine oil stop. 1. Park the vehicle on a level surface and stop the engine.

level at each fuel

2. Pull out the level gauge that has the “ ” symbol on top, wipe it clean, and insert it again. 3. Be sure the level gauge is correctly inserted until it stops.

Black plate (306,1)

1) Notch 2) Upper level Lower level 3)

4. Pull out the level gauge again and check the oil level on it. If it is below the lower level, add oil to bring the level up to the upper level.

CAUTION

. Use only engine oil with the recommended grade and vis- cosity.

. Be careful not to spill engine oil when adding it. If oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine oil gets on the exhaust

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

pipe, be sure to wipe it off.

If you check the oil level just after stopping the engine, wait a few minutes for the oil to drain back into the oil pan before checking the level. Just after driving or while the engine is warm, the engine oil level reading may be in a range between the upper level and the notch mark. This is caused by thermal expansion of the engine oil. To prevent overfilling the engine oil, do not add any additional oil above the upper level when the engine is cold. & Changing the oil and oil filter Change the oil and oil filter according to the maintenance schedule in the “War- ranty and Maintenance Booklet”. The engine oil and oil filter must be changed more frequently than listed in the maintenance schedule when driving on dusty roads, when short trips are frequently made, or when driving in extremely cold weather. 1. Warm up the engine by letting the engine idle for approximately 10 minutes to ease draining the engine oil. 2. Park the vehicle on a level surface and stop the engine. 3. Remove the oil filler cap.

Black plate (307,1)

Maintenance and service 11-9

properly.

WARNING

Be careful not to burn yourself with hot engine oil.

5. Wipe the seating surface of the drain plug with a clean cloth and tighten it securely with a new sealing washer after the oil has completely drained out. 6. Remove the under cover.

Turbo models

Turbo models

11

Non-turbo models

4. Drain out the engine oil by removing the drain plug while the engine is still warm. The used oil should be drained into an appropriate container and disposed of

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

11-10 Maintenance and service

Non-turbo models

7. Remove the oil filter with an oil filter wrench. 8. Before installing a new oil filter, apply a thin coat of engine oil to the seal. 9. Clean the rubber seal seating area of the bottom of engine and install the oil filter by hand turning. Be careful not to twist or damage the seal. 10. Tighten the oil filter by the amount indicated in the following table after the seal makes contact with the bottom of engine.

Oil filter color Part number

Black

15208AA100

Amount of

rotation 1 rotation

CAUTION

. Never over tighten the oil filter because that can result in an oil leak.

. Thoroughly wipe off any engine oil that has spilled over the exhaust pipe and/or under-cover. If spilled oil is not promptly wiped up, the oil could cause a fire.

11. Reinstall under cover. 12. Pour engine oil through the filler neck.

Oil capacity (guideline):

4.2 US qt (4.0 liters, 3.5 Imp qt)

The oil quantity indicated above is only guideline. The necessary quantity of oil depends on the quantity of oil that has been drained. The quantity of drained oil differs slightly depending on the temperature of the oil and the time the oil is left flowing out. After refilling the engine with oil, therefore, you

Black plate (308,1)

must use the level gauge to confirm that the level is correct. 13. Start the engine and make sure that no oil leaks appear around the filter’s rubber seal and drain plug. 14. Run the engine until it reaches the normal operating temperature. Then stop the engine and wait a few minutes to allow the oil drain back. Check the oil level again and if necessary, add more engine oil.

CAUTION

Be careful not to spill engine oil If oil touches the when adding it. exhaust pipe, it may cause a bad smell, smoke, and/or a fire.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

& Recommended grade and

viscosity

capabilities

Black plate (309,1)

Maintenance and service 11-11

Oil grade:

ILSAC GF-4, which can be identified with the ILSAC certification mark (Starburst mark) or API classification SM with the words “ENERGY CONSERVING”

These recommended oil grades can be identified by looking for either or both of the following marks displayed on the oil container.

API Service label 1)

Indicates the oil quality by API designa- tions Indicates the SAE oil viscosity grade Indicates that

the oil has fuel saving

2) 3)

ILSAC Certification Mark (Starburst Mark) In choosing an oil, you want the proper quality and viscosity, as well as one that will add to fuel economy. The following table lists the recommended viscosities and applicable temperatures. When adding oil, different brands may be used together as long as they are the same API classification and SAE viscosity as those recommended by SUBARU.

SAE viscosity No. and applicable tempera- ture *:

5W-30 is preferred.

Engine oil viscosity (thickness) affects fuel economy. Oils of lower viscosity provide better in hot weather, oil of higher viscosity is required to properly lubricate the engine.

fuel economy. However,

CAUTION

Use only engine oil with the recom- mended grade and viscosity.

11

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

11-12 Maintenance and service

& Recommended grade and

viscosity under severe driv- ing conditions

If the vehicle is used in desert areas, in areas with very high temperatures, or is used for heavy-duty applications, use of oil with the following grade and viscosities is recommended.

API classification SM (or SL):

SAE viscosity No.: 30, 40, 10W-50, 20W-40, 20W-50

& Synthetic oil You can use synthetic engine oil that meets the same requirements given for conventional engine oil. When using synthetic oil, you must use oil of the same classification, viscosity and grade shown in this Owner’s Manual, and must follow the oil and filter changing intervals shown in the maintenance schedule.

Cooling system

WARNING

Never attempt to remove the radia- tor cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boil- ing hot coolant when the cap is removed.

CAUTION

. Vehicles are filled at the factory with SUBARU Super Coolant that does not require the first change for 11 years/137,500 miles (11
years/220,000 km). This coolant should not be mixed with any other brand or type of coolant during this period. Mixing with a different coolant will reduce the life of the coolant. Should it be necessary to top up the coolant f o r a n y r e a s o n , u s e o n l y SUBARU Super Coolant. If the SUBARU Super Coolant is diluted with another brand or type, the maintenance interval is

Black plate (310,1)

shortened to that of the mixing coolant.

. Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface.

& Cooling fan, hose and con-

nections

Your vehicle employs an electric cooling fan which is thermostatically controlled to operate when the engine coolant reaches a specific temperature. If the radiator cooling fan does not operate even when the coolant temperature high warning light illuminates, the cooling fan circuit may be defective. Check the fuse and replace it if necessary. If the fuse is not blown, have the cooling system checked by your SUBARU dealer.

If frequent addition of coolant is neces- sary, there may be a leak in the engine cooling system. It is recommended that the cooling system and connections be checked for leaks, damage, or looseness.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

& Engine coolant ! Checking the coolant level

1) 2)

“FULL” level mark “LOW” level mark

Check the coolant level at each fuel stop. 1. Check the coolant level on the outside of the reservoir while the engine is cool. 2. If the level is close to or lower than the “LOW” level mark, add coolant up to the “FULL” level mark. If the reserve tank is empty, remove the radiator cap and refill as required.

3. After refilling the reserve tank and the radiator, reinstall the caps and check that the rubber gaskets inside the radiator cap are in the proper position.

CAUTION

. Be careful not

to spill engine coolant when adding it. If coolant touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine coolant gets on the exhaust pipe, be sure to wipe it off.

. Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface.

Black plate (311,1)

Maintenance and service 11-13

! Changing the coolant

WARNING

Never attempt to remove the radia- tor cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boil- ing hot coolant when the cap is removed.

Always add genuine SUBARU cooling system conditioner whenever the coolant is replaced. Change the engine coolant and add genuine SUBARU cooling system condi- tioner using the following procedures according to the maintenance schedule. 1. Remove the under cover.

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

11

11-14 Maintenance and service

Non-turbo models 1)

Fill up to this level

2. Place a proper container under the drain plug and loosen the drain plug. 3. Loosen the radiator cap to drain the coolant from the radiator. Then drain the coolant from the reserve tank. Tighten the drain plug securely. NOTE (turbo model only) The cap (without tabs) on top of the radiator does not need to be removed. To add coolant, remove the cap (with tabs) on the coolant tank on top of the engine. 4.

Install the under cover.

Turbo models 1)

Fill up to this level

5. Slowly pour the coolant and fill up to just below the filler neck, allowing enough

Black plate (312,1)

room to add genuine SUBARU cooling system conditioner in the radiator. Add genuine SUBARU cooling system condi- tioner until the coolant level reaches the filler neck. Do not pour the coolant too quickly, as this may lead to insufficient air bleeding and trapped air in the system.

Guideline of coolant quantity (including coolant in reservoir tank):

Non-turbo models:

MT: 7.2 US qt (6.8 liters, 6.0 Imp qt) AT: 7.1 US qt (6.7 liters, 5.9 Imp qt)

Turbo models:

8.5 US qt (8.0 liters, 7.0 Imp qt)

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (313,1)

Maintenance and service 11-15

Air cleaner element

WARNING

Do not operate the engine with the air cleaner element removed. The air cleaner element not only filters intake air but also stops flames if the engine backfires. the air cleaner element installed when the engine backfires, you could be burned.

is not

If

1) 2)

“FULL” level mark “LOW” level mark

CAUTION

. Be careful not

to spill engine coolant when adding it. If coolant touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine coolant gets on the exhaust pipe, be sure to wipe it off.

. Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface.

6. Pour the coolant and fill to the reser- voir tank’s “FULL” level mark.

7. Put the radiator cap back on and tighten firmly. At this time, make sure that the rubber gasket in the radiator cap is correctly in place. 8. Start and run the engine for more than 5 minutes at 2,000 to 3,000 rpm. 9. Stop the engine and wait until the coolant cools down (122 to 1408F [50 to 608C]). If there is any loss of coolant, add coolant to the radiator’s filler neck and to the reserve tank’s “FULL” level. 10. Put the radiator cap and reservoir cap back on and tighten firmly.

CAUTION

When replacing the air cleaner ele- ment, use a genuine SUBARU air cleaner element. If it is not used, there is the possibility of causing a negative effect to the engine.

The air cleaner element functions as a filter screen. When the element is perfo- rated or removed, engine wear will be excessive and engine life shortened.

The air cleaner element is a dry type. It is unnecessary to clean or wash the ele- ment.

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

11

Black plate (314,1)

11-16 Maintenance and service

& Replacing the air cleaner

element

Replace the air cleaner element according to the maintenance schedule in the “Warranty and Maintenance Booklet”. Un- der extremely dusty conditions, replace it more frequently. It is recommended that you always use genuine SUBARU parts. ! Non-turbo models

cleaner case. 3. Unsnap the two clips holding the air cleaner case cover.

6. To install the air cleaner case cover, insert the three projections on the air cleaner case cover into the slits on the air cleaner case and then snap the two clips on the air cleaner case cover.

4. Open the air cleaner case cover and remove the air cleaner element. 5. Clean the inside of the air cleaner cover and case with a damp cloth and install a new air cleaner element.

1) Connector 2) Clamp 3) Air intake boot 4) Clip

1. Unplug the connector that is attached to the top of the air cleaner case. 2. Loosen the screw of the clamp and pull the air

intake boot out of

the air

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

! Turbo models

to the top of the air cleaner case.

Black plate (315,1)

Maintenance and service 11-17

cover and case with a damp cloth and install a new air cleaner element.

1. Use a screwdriver to undo the clips on the air intake duct, then remove the air intake duct.

3. Unsnap the two clips holding the air cleaner case cover.

11

2. Unplug the connector that is attached

4. Open the air cleaner case cover and remove the air cleaner element. 5. Clean the inside of

the air cleaner

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (316,1)

11-18 Maintenance and service

Spark plugs

& Recommended spark plugs

Drive belts

Non-turbo models: FR5AP-11 (NGK)

Turbo models:

SILFR6A (NGK)

It may be difficult to replace the spark plugs. It is recommended that you have the spark plugs replaced by your SUBARU dealer.

The spark plugs should be replaced according to the maintenance schedule in the “Warranty and Maintenance Book- let”.

CAUTION

. When disconnecting the spark plug cables, always grasp the spark plug cap, not the cables.

. Make sure the cables are re-

placed in the correct order.

Front side belt

1) Power steering pump pulley 2) 3) Alternator 4) Air conditioner compressor pulley 5) Rear side belt 6) Crank pulley A)

98 N (10 kgf, 22 lbf)

The alternator, power steering pump, and air conditioner compressor depend on drive belts. Satisfactory performance re- quires that belt tension be correct.

To check the tension of the front side belt, place a straightedge (ruler) across two adjacent pulleys (alternator and crank pulley) and apply a force of 22 lbs (98 N, 10 kg) midway between the pulleys by

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Manual transmission oil & Checking the oil level

using a spring scale. Belt deflection should be the amount specified. the front side belt is loose, cracked, or worn, contact your SUBARU dealer.

If

in (mm)

Deflection

New belt 0.28 – 0.35
(7.0 – 9.0)

Used belt 0.35 – 0.43
(9.0 – 11.0)

The rear side belt is a stretch-type belt, and the deflection and tension do not need to be checked. If there are cracks or wear confirmed on the belts and a squeaking sound is heard from them, contact your SUBARU dealer.

1) Yellow handle

Check the oil level monthly. 1. Park the vehicle on a level surface and stop the engine. 2. Pull out the level gauge, wipe it clean, and insert it again.

Black plate (317,1)

Maintenance and service 11-19

1) Upper level 2) Lower level

3. Pull out the level gauge again and check the oil level on it. If it is below the lower through the level gauge hole to bring the level up to the upper level.

level, add oil

CAUTION

Be careful not to spill manual trans- mission oil when adding it. If oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If oil gets on the exhaust pipe, be sure to wipe it off.

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

11

11-20 Maintenance and service

& Recommended grade and

viscosity

Each oil manufacturer has its own base oils and additives. Never use different brands together.

Oil grade:

API classification GL-5

Automatic transmission fluid & Checking the fluid level The automatic transmission fluid expands largely as its temperature rises; the fluid level differs according to fluid temperature. Therefore, there are two different scales for checking the level of hot fluid and cold fluid on the level gauge.

range,

Though the fluid level can be checked without warming up the fluid on the “COLD” is recommended to check the fluid level when the fluid is at operating temperature. ! Checking the fluid level when the

it

fluid is hot

SAE viscosity No. and applicable tempera- ture

1. Drive the vehicle several miles to raise the temperature of the transmission fluid up to normal operating temperature; 158
to 1768F (70 to 808C) is normal. 2. Park the vehicle on a level surface and set the parking brake. 3. First shift the selector lever in each position. Then shift it in the “P” position, and run the engine at idling speed.

Black plate (318,1)

1) Yellow handle

1) HOT range 2) COLD range 3) Upper level Lower level 4)

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

& Recommended fluid

Use one of the following types of auto- matic transmission fluid. SUBARU ATF Type-HP IDEMITSU ATF HP

NOTE Using any non-specified type of auto- matic transmission fluid could result in damage inside the transmission. When replacing the automatic transmission fluid, be sure to use the kind specified.

4. Pull out the level gauge and check the fluid level on the gauge. If it is below the lower level on the “HOT” range, add the recommended automatic transmission fluid up to the upper level.

! Checking the fluid level when the

fluid is cold

When the fluid level has to be checked without time to warm up the automatic transmission, check to see that the fluid level is between the lower level and upper level on the “COLD” range. If it is below that range, add fluid up to the upper level. Be careful not to overfill.

CAUTION

Be careful not to spill automatic transmission fluid when adding it. If automatic transmission fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If automatic transmission fluid gets on the exhaust pipe, be sure to wipe it off.

Black plate (319,1)

Maintenance and service 11-21

Front differential gear oil (AT vehicles) & Checking the oil level

1) Yellow handle

1. Park the vehicle on a level surface and stop the engine. 2. Pull out the level gauge, wipe it clean, and insert it again.

11

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (320,1)

11-22 Maintenance and service

& Recommended grade and

viscosity

Each oil manufacturer has its own base oils and additives. Never use different brands together.

Oil grade:

API classification GL-5

Rear differential gear oil & Checking the gear oil level

1) Upper level 2) Lower level

3. Pull out the level gauge again and check the oil level on it. If it is below the lower level, add oil to bring the level up to the upper level.

CAUTION

Be careful not to spill front differ- ential gear oil when adding it. If oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If oil gets on the exhaust pipe, be sure to wipe it off.

1) Filler plug 2) Drain plug

SAE viscosity No. and applicable tempera- ture

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (321,1)

it off.

. If the vehicle requires frequent refilling, there may be an oil leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer.

Maintenance and service 11-23

& Recommended grade and

viscosity

Each oil manufacturer has its own base oils and additives. Never use different brands together.

Oil grade:

API classification GL-5

1) Filler hole 2) Drain hole 3) Oil level

Remove the plug from the filler hole and check the oil level. The oil level should be kept even with the bottom of the filler hole. If the oil level is below the bottom edge of the hole, add oil through the filler hole to raise the level.

CAUTION

. Be careful not to spill rear differ- ential gear oil when adding it. If rear differential gear oil touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If rear differential gear oil gets on the exhaust pipe, be sure to wipe

SAE viscosity No. and applicable tempera- ture

11

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

11-24 Maintenance and service

Power steering fluid & Checking the fluid level

The power steering fluid expands greatly as its temperature rises; the fluid level differs according to fluid temperature. Therefore, tank has two different checking ranges for hot and cold fluids.

the reservoir

Check the power steering fluid level monthly. 1. Park the vehicle on a level surface, and stop the engine.

level

the oil

2. Check the fluid level of the reservoir tank. When the fluid is hot after the vehicle has been run: Check that is between “HOT MIN” and “HOT MAX” on the surface of the reservoir tank. When the fluid is cool before the vehicle is run: Check that the oil is between “COLD MIN” and “COLD MAX” on the surface of the reservoir tank. 3. than the applicable “MIN” line, add the recom- mended fluid as necessary to bring the level between the “MIN” and “MAX” line.

the fluid level

is lower

level

If

If the fluid level is extremely low, it may indicate possible leakage. Consult your SUBARU dealer for an inspection.

Black plate (322,1)

WARNING

Be careful not because the fluid may be hot.

to burn yourself

CAUTION

. When power steering fluid is being added, use only clean fluid, and be careful not to allow any dirt into the tank. And never use different brands together.

. Avoid spilling fluid when adding

it in the tank.

. Be careful not

to spill power steering fluid when adding it. If power steering fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If power steering fluid gets on the exhaust pipe, be sure to wipe it off.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

& Recommended fluid

Use one of the following types of auto- matic transmission fluid. SUBARU ATF Type-HP IDEMITSU ATF HP

Brake fluid & Checking the fluid level

1) 2)

“MAX” level mark “MIN” level mark

Check the fluid level monthly. Check the fluid level on the outside of the reservoir. If the level is below “MIN”, add the recommended brake fluid to “MAX”. Use only brake fluid from a sealed container.

WARNING

. Never let brake fluid contact your eyes because brake fluid can be harmful If brake fluid gets in your eyes, immedi- ately flush them thoroughly with

to your eyes.

Black plate (323,1)

Maintenance and service 11-25

clean water. For safety, when performing this work, wearing eye protection is advisable.

. Brake fluid absorbs moisture from the air. Any absorbed moist- ure can cause a dangerous loss of braking performance.

. If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer.

CAUTION

. Never use different brands of brake fluid together. Also, avoid mixing DOT 3 and DOT 4 brake fluids even if they are of the same brand.

. When adding brake fluid, be care- ful not to allow any dirt into the reservoir.

. Never splash the brake fluid over painted surfaces or rubber parts. Alcohol contained in the brake fluid may damage them.

. Be careful not to spill brake fluid when adding it. If brake fluid touches the exhaust pipe, it may

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

11

11-26 Maintenance and service

cause a bad smell, smoke, and/or a fire. If brake fluid gets on the exhaust pipe, be sure to wipe it off.

Clutch fluid (MT vehicles) & Checking the fluid level

& Recommended brake fluid

FMVSS No. 116, fresh DOT 3 brake fluid

Check the fluid level on the outside of the reservoir. If the level is below “MIN” level mark, add the recommended clutch fluid to “MAX” level mark. Use only clutch fluid from a sealed container.

WARNING

Never let clutch fluid contact your eyes because clutch fluid can be harmful to your eyes. If clutch fluid gets in your eyes, immediately flush them thoroughly with clean water. For safety, when performing this work, wearing eye protection is

Black plate (324,1)

advisable.

CAUTION

. Clutch fluid absorbs moisture from the air. Any absorbed moist- ure can cause improper clutch operation.

. If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer.

. Never use different brands of

clutch fluid together.

. When clutch fluid is added, be careful not to allow any dirt into the tank.

. Never splash the clutch fluid over painted surfaces or rubber parts. Alcohol contained in the clutch fluid may damage them.

. Be careful not to spill clutch fluid when adding it. If clutch fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If clutch fluid gets on the exhaust pipe, be sure to wipe it off.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

& Recommended clutch fluid

Brake booster

FMVSS No. 116, fresh DOT 3 brake fluid

If the brake booster does not operate as described in the following, have it checked by your SUBARU dealer. 1. With the engine off, depress the brake pedal several times, applying the same pedal force each time. The distance the pedal travels should not vary. 2. With the brake pedal depressed, start the engine. The pedal should move slightly down to the floor. 3. With the brake pedal depressed, stop the engine and keep the pedal depressed for 30 seconds. The pedal height should not change. 4. Start the engine again and run for approximately 1 minute then turn it off. Depress the brake pedal several times to check the brake booster. The brake booster operates properly if the pedal stroke decreases with each depression.

NOTE For vehicles equipped with the brake assist system, when you depress the brake pedal strongly or suddenly, the following phenomena occur. However, even though these occur, they do not indicate any malfunctions, and the brake assist system is operating prop-

Black plate (325,1)

Maintenance and service 11-27

erly. . You might feel that the brake pedal is applied by lighter force and gener- ates a greater braking force. . You might hear clicking (knocking) sounds around brake pedal.

Brake assist is not a system that brings more braking ability to the vehicle beyond its breaking capability.

11

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

11-28 Maintenance and service

Brake pedal

Check the brake pedal free play and reserve distance according to the main- tenance schedule in the “Warranty and Maintenance Booklet”.

& Checking the brake pedal

free play

& Checking the brake pedal

reserve distance

1) More than 2.56 in (65 mm)

Depress the pedal with a force of approxi- mately 66 lbs (294 N, 30 kg) and measure the distance between the upper surface of the pedal pad and the floor. When the measurement is smaller than the specification, or when the pedal does not operate smoothly, contact with your SUBARU dealer.

1)

0.02 – 0.08 in (0.5 – 2.0 mm)

Stop the engine and firmly depress the brake pedal several times. Lightly pull the brake pedal up with one finger to check the free play with a force of less than 2 lbs (10 N, 1 kg). the free play is not within proper If specification, contact your SUBARU deal- er.

Black plate (326,1)

Clutch pedal (MT vehicles)

Check the clutch pedal free play and reserve distance according to the main- tenance schedule in the “Warranty and Maintenance Booklet”.

& Checking the clutch function Check the clutch engagement and disen- gagement. 1. With the engine idling, check that there are no abnormal noises when the clutch pedal is depressed, and that shifting into 1st or reverse feels smooth. 2. Start the vehicle by releasing the pedal slowly to check that the engine and transmission smoothly couple without any sign of slippage.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (327,1)

Maintenance and service 11-29

& Checking the clutch pedal

free play

Hill start assist system (MT vehicles)

Replacement of brake pad and lining

the Hill start assist system the following

Ensure that operates properly under circumstances: 1. Stop the vehicle on an uphill grade by depressing the brake pedal and clutch pedal, with the engine running. 2. Make sure that the vehicle does not move backward even after the brake pedal is released. 3. Then make sure the vehicle starts climbing the grade by following the normal starting procedures.

If the Hill start assist system does not operate as described above, contact with your SUBARU dealer.

1)

0.16 – 0.51 in (4.0 – 13.0 mm)

Lightly press the clutch pedal down with your finger until you feel resistance, and check the free play. If the free play is not within proper specification, contact your SUBARU deal- er.

11

The right front disc brake and the right rear disc brake have audible wear indicators on the brake pads. If the brake pads wear close to their service limit, the wear indicator makes a very audible scraping noise when the brake pedal is applied.

If you hear this scraping noise each time you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as possible.

CAUTION

If you continue to drive despite the scraping noise from the audible it will brake pad wear indicator, – CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Black plate (328,1)

11-30 Maintenance and service

result in the need for costly brake rotor repair or replacement.

range, adjust it by turning the adjusting nut located on the parking brake lever.

Parking brake stroke

Parking brake stroke:

7 – 8 notches / 44 lbs (196 N, 20 kg)

WARNING

A safe location and situation should be selected for break-in driving.

CAUTION

Pulling the parking brake lever too forcefully may cause the rear wheels to lock. To avoid this, be certain to pull the lever up slowly and gently.

& Breaking-in of new brake

pads and linings

lightly. Repeat

When replacing the brake pad or lining, use only genuine SUBARU parts. After replacement, the new parts must be broken in as follows: ! Brake pad and lining While maintaining a speed of 30 to 40
mph (50 to 65 km/h), step on the brake pedal this five or more times. ! Parking brake lining 1. Drive the vehicle at a speed of approximately 22 mph (35 km/h). 2. With the parking brake release button pushed in, pull the parking brake lever SLOWLY and GENTLY. (Pulling with a force of approximately 33 lbs [147 N, 15
kg].) 3. Drive the vehicle for approximately 220 yards (200 meters) in this condition. 4. Wait 5 to 10 minutes for the parking brake to cool down. Repeat this proce- dure. 5. Check the parking brake stroke. If the parking brake stroke is out of the specified

Check the parking brake stroke according to the maintenance schedule in the “Warranty and Maintenance Booklet”. When the parking brake is properly adjusted, braking power is fully applied by pulling the lever up seven to eight notches gently but firmly (approximately 44 lbs [196 N, 20 kg]). If the parking brake lever stroke is not within the specified range, have the brake system checked and adjusted at your SUBARU dealer.

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

Tires and wheels & Types of tires You should be familiar with type of tires present on your vehicle. The factory-fitted tires are all-season tires. ! All season tires All season tires are designed to provide an adequate measure of traction, handling and braking performance in year-round driving including snowy and icy road conditions. However all season tires do not offer as much traction performance as winter (snow) tires in heavy or loose snow or on icy roads. All season tires are identified by “ALL SEASON” and/or “M+S” (Mud & Snow) on the tire sidewall. ! Summer tires Summer tires are high-speed capability tires best suited for highway driving under dry conditions. Summer tires are inadequate for driving on slippery roads such as on snow- covered or icy roads. If you drive your vehicle on snow-covered or icy roads, we strongly recommend the use of winter (snow) tires. When installing winter tires, be sure to replace all four tires.

! Winter (snow) tires Winter tires are best suited for driving on snow-covered and icy roads. However winter tires do not perform as well as summer tires and all season tires on roads other than snow-covered and icy roads.

& Tire pressure monitoring

system (TPMS) (U.S.-spec. models)

The tire pressure monitoring system pro- vides the driver with a warning message by sending a signal from a sensor that is installed in each wheel when tire pressure is severely low. The tire pressure monitor- ing system will activate only when the vehicle is driven. Also, this system may not react immediately to a sudden drop in tire pressure (for example, a blow-out caused by running over a sharp object).

If you adjust the tire pressures in a warm garage and will then drive the vehicle in cold outside air, the resulting drop in tire pressures may cause the low tire pressure warning light to illuminate. To avoid this problem when adjusting the tire pressures in a warm garage, inflate the tires to pressures higher than those shown on the tire placard. Specifically, inflate them by an extra 1 psi (6.9 kPa, 0.07 kgf/cm2) for every difference of 108F (5.68C) between

Black plate (329,1)

Maintenance and service 11-31

the temperature in the garage and the temperature outside. By way of example, the following table shows the required tire pressures that correspond to various out- side temperatures when the temperature in the garage is 608F (15.68C). Example: Tire size: P215/65R16 96H Standard tire pressures: Front: 30 psi (210 kPa, 2.1 kgf/cm2) Rear: 29 psi (200 kPa, 2.0 kgf/cm2) Garage temperature: 608F (15.68C)

Outside

temperature

Adjusted pressure [psi (kPa, kgf/cm2)] rear front

308F (−18C)

108F (−128C)

−108F (−238C)

33

(230, 2.3)

35

(240, 2.4)

37

(255, 2.55)

32

(220, 2.2)

34

(235, 2.35)

36

(250, 2.5)

Example: Tire size: P225/55R17 95H Standard tire pressures: Front: 32 psi (220 kPa, 2.2 kgf/cm2) Rear: 30 psi (210 kPa, 2.1 kgf/cm2) Garage temperature: 608F (15.68C)

– CONTINUED –

北米Model "A8140BE-B" EDITED: 2008/ 2/ 28

11

11-32 Maintenance and service

Outside

temperature

308F (−18C)

108F (−128C)

−108F (−238C)

Adjusted pressure [psi (kPa, kgf/cm2)] front rear 33

35

(240, 2.4)

(230, 2.3)

37

(255, 2.55)

39

(270, 2.7)

35

(240, 2.4)

37

(255, 2.55)

If the low tire pressure warning light illuminates when you drive the vehicle in cold outside air after adjusting the tire pressures in a warm garage, re-adjust the tire pressures using the method described above. Then, increase the vehicle speed to at least 20 mph (32 km/h) and check to see that the low tire pressure warning light turns off a few minutes later. If the low tire pressure warning light does not turn off, the tire pressure monitoring system may not be functioning normally. In this event, go to a SUBARU dealer to have the system inspected as soon as possible.

While the vehicle is driven, friction be- tween tires and the road surface causes the tires to warm up. After illumination of the low tire pressure warning light, any increase in the tire pressures caused by an increase in the outside air temperature or by an increase in the temperature in the

tires can cause the low tire pressure warning light to turn off.

System resetting is necessary when the wheels are changed (for example, a switch to snow tires) and new TPMS valves are installed on the newly fitted wheels. Have this work performed by a SUBARU dealer following wheel replace- ment.

It may not be possible to install TPMS valves on certain wheels that are on the market. Therefore, if you change the wheels (for example, a switch to snow tires), use wheels that have the same part number as the standard-equipment wheels. Without four operational TPMS valve/sensors on the wheels, the TPMS will not fully function and the warning light in the instrument panel will illuminate steadily after blinking for approximately one minute.

When a tire is replaced, adjustments are necessary to ensure continued normal operation of the tire pressure monitoring system. As with wheel replacement, there- fore, you should have the work performed by a SUBARU dealer.

Black plate (330,1)

WARNING

If the low tire pressure warning light does not illuminate briefly after the ignition switch is turned ON or the light illuminates steadily after blink- ing for approximately one minute, you should have your Tire Pressure Monitoring System checked at a SUBARU dealer as soon as possi- ble. If this light illuminates while driving, never brake suddenly and keep driving straight ahead while gradu- ally reducing speed. Then slowly pull off the road to a safe place. Otherwise an accident involving serious vehicle damage and serious personal injury could occur. If illuminates while driving after adjusting the tire pres- sure, a tire may have significant damage and a fast leak that causes the tire to lose air rapidly. If you have a flat tire, replace it with a spare tire as soon as possible. When a spare tire is mounted or a