2001 Subaru Forester Owners Manual

5. Close the doors. The system will automatically arm after one min- ute.

In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door lock switch is used to lock the vehicle, arm- ing will take place immediately regardless of whether or not the pas- sive mode has been selected.

– CONTINUED –

2-17

FORESTER (72F) NA (E) A8040B

B Disarming the system To disarm the system, briefly press the “UNLOCK/DISARM” button on the transmitter.

B Tripped sensor identification If the horn sounds four times and the parking lights flash four times when you disarm the system, this indicates that the alarm was trig- gered. The number of times the indicator light flashes indicates what sensor caused the alarm condition.

To enter identification mode: 1. Open the driver’s door and leave it open. 2. Turn the ignition switch to the “ON” position two times. (“LOCK” → “ON” → “LOCK” → “ON” → “LOCK”) 3. The indicator light will start flashing.

The indicator light provides the following indications. Flashing one time: Any door or the rear gate has been opened. Flashing three times: The impact sensor in the system’s unit has been activated. This may indicate that your vehicle has been shocked or tampered with by some outside force and/or unauthorized person. Flashing four times: The ignition switch has been turned on.

To exit this mode, close the door and turn the ignition switch to the “ON” position.

2-18

FORESTER (72F) NA (E) A8040B

Doors and locks

Child safety locks

Unlock

Lock

HS0015

WARNING

Always use the child safety lock whenever a child rides in the rear seat. Serious injury could result if a child accidentally opened the door and fell out.

Each rear door has a child safety lock that prevents the doors from being opened even if the inside door handle is pulled.

When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever. The door can only be opened from the outside.

– CONTINUED –

2-19

FORESTER (72F) NA (E) A8040B

Power windows

WARNING

D When operating power windows, be extremely careful to pre- vent anyone’s fingers, arms or head from being caught in the window. D Always lock the passengers’ windows using the lock switch when children are riding in the vehicle. D Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the power window.

The power windows operate only when the ignition switch is in the “ON” position.

B Power window switch cluster (driver’s side)

Lock switch

“AUTO” switch for driver’s window

For rear left passenger’s window

For front passenger’s window

For rear right passenger’s window

HS0017

2-20

FORESTER (72F) NA (E) A8040B

Doors and locks

Lock

Unlock

Close

Open

Automatically open

Close

Open

HS0018

All door windows can be controlled by the power window switch clus- ter at the driver side door.

n To open or close the driver’s window AUTO switch: This switch has two functions. Push the switch down until it clicks and release it, and the window will fully open. To stop the window halfway, pull the switch up slightly.

Push the switch down lightly and hold it. The window will open as long as the switch is held. Pull the switch up lightly and hold it. The window will close as long as the switch is held.

n To open or close the passengers’ windows To open the passengers’ windows, push the appropriate switch down and hold it until the window reaches the desired position. To close the window, pull the switch up and hold it until it reaches the desired posi- tion.

n To lock the passengers’ windows To lock the passengers’ windows, push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ windows cannot be opened or closed.

– CONTINUED –

2-21

FORESTER (72F) NA (E) A8040B

B Front passenger’s switch

Close

Open

HS0019

To open the window, push the switch down and hold it until the win- dow reaches the desired position. To close the window, pull the switch up and hold it until the window reaches the desired position.

When the lock switch on the power window switch cluster, located on the driver’s side door, is in the “LOCK” position, the front passenger’s window cannot be operated with the front passenger’s switch.

B Rear passenger’s switches

Close

Open

HS0020

To open the window, push the switch down and hold it until the win- dow reaches the desired position. To close the window, push the switch up and hold it until the window reaches the desired position.

When the lock switch on the power window switch cluster, located on

2-22

FORESTER (72F) NA (E) A8040B

Doors and locks

the driver’s side door, is in the “LOCK” position, the rear passengers’ windows cannot be operated with the rear passengers’ switches.

Rear gate

WARNING

D Do not attempt to shut the rear gate while holding the inside handle. Also avoid closing the rear gate by pulling on the inside handle from inside the cargo space. There is a danger of your hand being caught and injured. D To prevent dangerous exhaust gas from entering the vehicle, always keep the rear gate closed while driving.

Lock

Unlock

HS0021

To unlock the rear gate, insert the key in the keyhole and turn it clock- wise. To lock the rear gate, insert the key in the keyhole and turn it coun- terclockwise. Since your vehicle is equipped with power door locks, the rear gate can also be locked and unlocked by operating the driver’s door lock. To open the rear gate, first unlock the rear gate lock then pull the outside handle up. To close the rear gate, lower it slowly and push down firmly until the latch engages. The rear gate can be lowered easily if you pull down on the inside handle as shown in the illustration.

– CONTINUED –

2-23

FORESTER (72F) NA (E) A8040B

HS2007BA

Moonroof (if equipped)

WARNING

D Never let anyone’s hands, arms, head or any objects protrude from the moonroof. D Before closing the moonroof, make sure that no one’s hands, arms, head or other objects will be accidentally caught in the moonroof.

CAUTION

D Do not sit on the edge of the open moonroof. D Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut.

The moonroof operates only when the ignition switch is in the “ON” posi- tion.

2-24

FORESTER (72F) NA (E) A8040B

Doors and locks

Open/close switch

HS0294

To open or close the moonroof Push the upper part of the switch to open the moonroof. The sun shade also will be opened together with the moonroof. The moonroof will stop at a position 20 in. (50 cm) away from the fully closed position if you contin- ue to press on the switch. Release the switch once and push it again to open the moonroof completely. Push the lower part of the switch to close the moonroof. The moonroof will stop at a position 6 in. (15 cm) away from the fully closed position if you continue to press on the switch. Release the switch once and push it again to close the moonroof completely.

After washing the vehicle or after it rains, wipe away water on the roof prior to opening the moonroof to prevent water drops from falling into the passenger compartment.

NOTE D For the sake of safety, it is recommended that you avoid driving with the moonroof opened beyond the initial stop position of 20 in (50 cm). D Driving with the moonroof fully open can cause an annoying sound to generate at high speeds. If such a condition has been encountered, close the moonroof up to the initial stop position of 20
in. (50 cm). D If the moonroof cannot be closed through switch operation because of system failure, it can be closed manually using a hex-

– CONTINUED –

2-25

FORESTER (72F) NA (E) A8040B

head wrench. For the procedure, refer to “Moonroof — if the moon- roof cannot be closed” in Chapter 9 “In case of emergency”.

B Sun shade

HS0292

The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.

2-26

FORESTER (72F) NA (E) A8040B

Instruments and controls

Ignition switch

Key reminder chime Key interlock release (AT vehicles only)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hazard warning flasher Gauges

Speedometer Odometer/Trip meter Tachometer Outside temperature indicator (if equipped) Fuel gauge Temperature gauge

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warning and indicator lights

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Seatbelt warning light and chime SRS airbag system warning light CHECK ENGINE warning light/Malfunction indicator lamp Charge warning light Oil pressure warning light AT OIL TEMPerature warning light (for AT vehicles) ABS warning light (for vehicles with ABS) Brake system warning light Door open warning lights Front-wheel drive warning light (for AT vehicles) Security system status indicator light (if equipped) Turn signal indicator lights High beam indicator Light control switch Turn signals lever Illumination brightness control Parking light switch Fog light switch (if equipped) Wiper and washer

Windshield wiper and washer switches Rear window wiper and washer switch (if equipped)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Windshield wiper deicer (if equipped) Rear window defogger switch Tilt steering wheel Horn Mirrors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inside mirror Outside mirrors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-2
3-4
3-4
3-5
3-6
3-6
3-6
3-7
3-7
3-8
3-9
3-9
3-10
3-10
3-11
3-12
3-12
3-13
3-13
3-14
3-15
3-15
3-15
3-15
3-15
3-16
3-18
3-18
3-19
3-20
3-20
3-22
3-24
3-25
3-26
3-27
3-28
3-28
3-28
3-31

FORESTER (72F) NA (E) A8040B

Ignition switch

WARNING

Never turn the ignition switch to “LOCK” while the vehicle is be- ing driven or towed because that will lock the steering wheel, pre- venting steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.

The ignition switch has four positions: LOCK, ACC, ON and START.

HS0122

B LOCK The key can only be inserted or removed in this position. The ignition switch will lock the steering wheel when you remove the key. If turning the key is difficult, turn the steering wheel slightly to the right and left as you turn the key.

3-2

FORESTER (72F) NA (E) A8040B

Instruments and controls

n Automatic transmission vehicles:

HS0123

HS0124

The key can be turned from “ACC” to “LOCK” only when the selector lever is in the “P” position.

n Manual transmission vehicles:

HS0125

The key can be turned from “ACC” to “LOCK” only when the key is pushed in while turning it.

B ACC In this position the electrical accessories (radio, accessory power socket, etc.) can be used.

B ON This is the normal operating position after the engine is started.

– CONTINUED –

3-3

FORESTER (72F) NA (E) A8040B

B START

CAUTION

Do not turn the ignition switch to the “START” position while the engine is running.

The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position.

J Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “ACC” positions. The chime stops when the key is re- moved from the ignition switch.

J Key interlock release (AT vehicles only) If the key can not be turned to the “LOCK” position even when the selec- tor lever is in the “P” position:

Release lever

HS0126

Vehicle front

HS0127

1. Take out the screwdriver from the tool bag. 2. Remove three screws securing the undercover of the steering col- umn. 3. Remove the under cover of the steering column. 4. Turn the ignition key while pressing the key interlock release lever.

Take your vehicle to the nearest SUBARU dealer immediately to have the

3-4

FORESTER (72F) NA (E) A8040B

Instruments and controls

key interlock system repaired.

Hazard warning flasher

HS0053

The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions. The hazard warning flasher works with the ignition switch in any position.

When you have to park your vehicle under emergency conditions, pull off the roads safely and park away from the traffic if it is possible.

To turn on the hazard warning flasher, push the hazard warning button on the instrument panel. To turn off the flasher, push the button again.

NOTE When the hazard warning flasher is on, the turn signals do not work.

– CONTINUED –

3-5

FORESTER (72F) NA (E) A8040B

Gauges

HSF013CB

J Speedometer The speedometer shows the vehicle speed.

J Odometer/Trip meter

CAUTION

To ensure safety, do not attempt to change the function of the in- dicator during driving, as an accident from inadequate steering operation could result.

This meter displays the odometer and two trip meters when the ignition

HS3005BB

3-6

3

FORESTER (72F) NA (E) A8040B

Instruments and controls

switch is in the “LOCK”, “ACC” or “ON” position. To change the mode indication, briefly push the knob. Each press of the knob changes the function in the following order.

A trip meter

B trip meter

B Odometer The odometer shows the total distance that the vehicle has been driv- en.

B Double trip meter The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To set the trip meter to zero, select the indication of the A trip or B trip meter by pushing the knob and keep the knob pushed for more than 2 seconds.

NOTE If the connection between the combination meter and battery is bro- ken for any reason such as vehicle maintenance or fuse replace- ment, the data recorded on the trip meter will be lost.

J Tachometer

CAUTION

Do not operate the engine with the pointer of the tachometer in the red zone. In this range, fuel injection will be cut by the engine control module to protect the engine from overrevving. The en- gine will resume running normally after the engine speed is re- duced below the red zone.

The tachometer shows the engine speed in thousands of revolutions per minute.

J Outside temperature indicator (if equipped) The outside temperature indicator shows the outside temperature in a range from –22°F to 113°F (–30°C to 45°C).

– CONTINUED –

3-7

FORESTER (72F) NA (E) A8040B

The indicator can give a false reading under any of the following condi- tions: D When there is too much sun. D During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately following a shutdown. D When the actual outside temperature falls outside the specified indi- cator range.

J Fuel gauge

Low fuel warning light

HS0155

The fuel gauge shows the approximate amount of fuel remaining in the tank. The gauge does not return to “E” even though the ignition switch is in the “ACC” or “LOCK” position.

The gauge may move slightly during braking, turning or acceleration due to fuel movement in the tank.

B Low fuel warning light The low fuel warning light comes on when the tank is nearly empty (about 2.3 U.S. gal., 9.0 liters, 1.9 Imp. gal.). It only operates when the ignition switch is in the “ON” position.

3-8

FORESTER (72F) NA (E) A8040B

Instruments and controls

J Temperature gauge

CAUTION

If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possible. See “In case of emergency” in this manual.

Normal operating range

HS0052

The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position.

The coolant temperature will vary in accordance with the outside temper- ature and driving conditions.

We recommend that you drive moderately until the pointer of the tempera- ture gauge reaches near the middle of the range. Engine operation is opti- mum with the engine coolant at this temperature range and high revving operation when the engine is not warmed up enough should be avoided.

Warning and indicator lights

Several of the warning and indicator lights come on momentarily and then go out when the ignition switch is initially turned to the “ON” posi- tion. This permits checking the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position. The following lights come on:

– CONTINUED –

3-9

FORESTER (72F) NA (E) A8040B

Seatbelt warning light SRS airbag system warning light CHECK ENGINE warning light/Malfunction indicator lamp Charge warning light Oil pressure warning light AT OIL TEMP warning light (automatic transmission vehicles) ABS warning light (if equipped) Brake system warning light

If any lights fail to come on, it indicates a burned-out bulb or a malfunc- tion of the corresponding system. Consult your authorized SUBARU dealer for repair.

J Seatbelt warning light and chime When the ignition switch is turned to the “ON” position, the seatbelt warning light will come on and the reminder chime will sound to remind driver to fasten the seatbelt. The seatbelt warning light remains on for about six seconds and turns off automatically after six seconds. The seatbelt reminder chime will turn off when the driver’s side seatbelt is buckled or it will turn off automatically after about six seconds.

J SRS airbag system warning light AIRBAG When the ignition switch is turned to the “ON” position, the SRS airbag system warning light will come on for about six seconds and go out. This shows the SRS airbag system is in normal operation. If this light comes on while driving or remains illuminated even after a lapse of about 6 seconds from when the ignition key has been turned on, it may indicate that the SRS airbag system is not working properly. Con- tact your nearest SUBARU dealer immediately.

3-10

FORESTER (72F) NA (E) A8040B

Instruments and controls

J CHECK ENGINE warning light/

Malfunction indicator lamp

CAUTION

If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possible. Continued vehicle operation without having the emission control system checked and repaired as necessary could cause serious damage, which may not be covered by your vehicle’s warranty.

If this light comes on steadily or blinks while the engine is running, it may indicate that there is a problem or potential problem somewhere in the emission control system.

B If the light comes on steadily: If the light comes on steadily while driving or does not go out after the engine starts, an emission control system malfunction has been de- tected. You should have your vehicle checked by an authorized SUBARU dealer immediately.

NOTE This light also comes on when the fuel filler cap is not tightened until it clicks.

If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indicator lamp coming on could be a loose or missing fuel filler cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK ENGINE warning light turn off immediately. It may take several driving trips. If the light does not go out, take your vehicle to your authorized SUBARU dealer immediately.

B If the light is blinking: If the light is blinking while driving, an engine misfire condition has

– CONTINUED –

3-11

FORESTER (72F) NA (E) A8040B

been detected which may damage the emission control system. To prevent serious damage to the emission control system, you should do the following: D Reduce vehicle speed. D Avoid hard acceleration. D Avoid steep uphill grades. D Reduce the amount of cargo, if possible. D Stop towing a trailer as soon as possible.

The CHECK ENGINE warning light may stop blinking and come on steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately.

J Charge warning light If this light comes on when the engine is running, it may indicate that the charging system is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the alterna- tor belt. If the belt is loose, broken or if the belt is in good condition but the light remains on, contact your nearest SUBARU dealer immediately.

J Oil pressure warning light

CAUTION

Do not operate the engine with the oil pressure warning light on. This may cause serious engine damage.

If this light comes on when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system is not working prop- erly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil level is low, add oil immediately. If the engine oil is at the proper level but the light remains on, contact your nearest SUBARU dealer immediately.

3-12

FORESTER (72F) NA (E) A8040B

Instruments and controls

J AT OIL TEMPerature warning light

(for AT vehicles)

If this light comes on when the engine is running, it may indicate that the automatic transmission fluid temperature is too hot.

If the light comes on while driving, it is unnecessary to stop the vehicle, but avoid driving up steep grades or in stop and go traffic.

B Automatic transmission control system warning If the light flashes after the engine starts, it may indicate that the auto- matic transmission control system is not working properly. Contact your nearest SUBARU dealer for service immediately.

J ABS warning light

(for vehicles with ABS)

(U.S.) (Canada) The ABS warning light comes on when the ignition switch is turned to the “ON” position and goes out after about two seconds. This is an indication that the ABS system is working properly.

ABS

CAUTION

If the warning light behaves as follows, the ABS system may not work properly. When the warning light is on, the ABS function shuts down; however, the conventional brake system continues to operate normally.

D The warning light does not come on when the ignition switch is turned to the “ON” position. D The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8 mph (12 km/h). D The warning light comes on during driving.

If this occurs, have the ABS system repaired at the first available opportunity by your SUBARU dealer.

– CONTINUED –

3-13

FORESTER (72F) NA (E) A8040B

NOTE If the warning light behavior is as shown below, the ABS system may be considered normal. D The warning light comes on right after the engine is started but goes out immediately, remaining off. D The warning light remains on after the engine has been started, but it goes out when the vehicle speed reaches about 8 mph (12
km/h). D The warning light comes on during driving, but it goes out immediately and remains off. When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning light may come on. This is due to the low battery voltage and does not indicate a malfunction. When the battery becomes fully charged, the light will go out.

J Brake system warning light

BRAKE (U.S.) (Canada)

WARNING

D Driving with the brake system warning light on is dangerous. This indicates your brake system may not be working properly. If the light remains on, have the brakes inspected by a SUBARU dealer immediately. D If at all in doubt about whether the brakes are operating prop- erly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for repair.

This light has the following two functions:

B Parking brake warning The light comes on with the parking brake applied while the ignition switch is in the “ON” position. It goes out when the parking brake is fully released.

B Brake fluid level warning This light comes on when the brake fluid level has dropped to near the “MIN” level of the brake fluid reservoir with the ignition switch in

3-14

FORESTER (72F) NA (E) A8040B

Instruments and controls

the “ON” position and with the parking brake fully released.

If the brake system warning light should come on while driving (with the parking brake fully released and with the ignition switch posi- tioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. Have your vehicle checked by a SUBARU dealer immediately.

J Door open warning lights The door open warning light comes on if any door or the rear gate is not fully closed.

Always make sure this light is out before you start to drive.

J Front-wheel drive warning light (for AT vehicles) This light comes on when All Wheel Drive is disengaged and the drive mechanism is switched to Front Wheel Drive for maintenance or similar purposes.

J Security system status indicator light

(if equipped)

This light is found at the bottom center of the combination meter panel. On vehicles equipped with a security system, it blinks to show the driver the operational status of the security system. For detailed information, re- fer to the “Security system” in Chapter 2.

J Turn signal indicator lights These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to “Re- placing bulbs” section in Chapter 10.

J High beam indicator This light shows that the headlights are in the high beam mode. This indicator light also comes on when operating headlight flasher.

– CONTINUED –

3-15

FORESTER (72F) NA (E) A8040B

Light control switch

WARNING

To prevent battery discharge resulting from accidentally leaving your lights on when your vehicle is parked, the light switch oper- ates only when the ignition switch is in the “ON” position. In any other position, the vehicle’s lights will be out. If you park your ve- hicle on a roadside at night, use the hazard warning flasher to alert the other drivers.

Dimmer

Headlight flasher

HS0054

HS0055

The light switch operates only when the ignition switch is in the “ON” position.

B Headlights To turn on the headlights, turn the knob on the end of the turn signal lever.

first position

Parking lights, instrument panel illumination, tail lights and license plate light are on.

second position

Headlights, parking lights, instrument panel illumination, tail lights, and license plate light are on.

3-16

FORESTER (72F) NA (E) A8040B

Instruments and controls

B High/low beam change (dimmer) To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indi- cator light “a” on the instrument panel is also on. To switch back to low beam, pull the lever back to the detent position.

B Headlight flasher

CAUTION

Do not hold the lever in the flashing position for more than just a few seconds.

To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the lighting switch is in the “OFF” position.

When the headlights are on high beam, the high beam indicator light “a” on the instrment panel also comes on.

B Daytime running light system (for CANADA models)

WARNING

The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switch must always be turned to the “a” position when it is dark out- side.

The low beam headlights will automatically come on at reduced brightness when the engine has started, under the following condi- tions:

D The parking brake is fully released. D The automatic transmission selector lever is set at other than the “P” position. D The light switch is in the “OFF” position.

– CONTINUED –

3-17

FORESTER (72F) NA (E) A8040B

Turn signals lever

Right turn

Left turn

HS0056

To activate the right turn signal, push the turn signal lever up. To activate the left turn signal, push the turn signal lever down. When the turn is fin- ished, the lever will return automatically. If the lever does not return after cornering, return the lever to the neutral position by hand.

To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction of the turn or lane change. The lever will return auto- matically to the neutral position when you release it.

Illumination brightness control

Brighten

Darken

HS0057

3-18

FORESTER (72F) NA (E) A8040B

Instruments and controls

When the lighting switch is in the “p” or “a” position, you can adjust brightness of the instrument panel illumination for better visibility. To brighten, turn the control dial counterclockwise. To darken, turn the control dial clockwise.

Parking light switch

HS0058

The parking light switch operates regardless of the ignition switch posi- tion.

By pushing the front end of this switch, following lights will come on.

– Parking lights – Front side marker lights – Tail lights – License plate lights

To turn off, push the rear end of the parking light switch. Avoid leaving these lights on for a long time because that will run down the battery.

– CONTINUED –

3-19

FORESTER (72F) NA (E) A8040B

Fog light switch (if equipped)

The fog lights operate only when the headlights are on low beam. Push the fog light switch to turn the fog lights on. Press the switch again to turn them off.

HB2025BB

The indicator light located on the switch will illuminate when the fog lights are on.

Wiper and washer

WARNING

In freezing weather, do not use the windshield washer until the windshield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view.

CAUTION

D Do not operate the washer continuously for more than ten se- conds, or when the washer fluid tank is empty. This may cause overheating of the washer motor. Check the washer fluid level fre- quently, such as at fuel stops.

3-20

3

FORESTER (72F) NA (E) A8040B

Instruments and controls

D Do not operate the wipers when the windshield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the windshield washer. D In freezing weather, be sure that the wiper blades are not fro- zen to the windshield or rear window before switching on the wipers. Attempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper motor to burn out. If the wiper blade is frozen to the window glass, be sure to operate the defroster, wiper deicer (if equipped) or rear window defogger before turning on the wiper. D If the wipers stop during operation because of ice or some oth- er obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper opera- tion. D Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. (See “Windshield washer fluid” section in chapter 11.) Also, when driving the vehicle when there are freezing tempera- tures, use non-freezing type wiper blades. D Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper blades.

NOTE D The wiper operates only when the ignition switch is in the “ON” or “ACC” position. D Clean your wiper blades and window glass periodically with a washer solution to prevent streaking, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the

– CONTINUED –

3-21

FORESTER (72F) NA (E) A8040B

windshield or rear window. D Grease, wax, insects or other material on the windshield or the wiper blades results in jerky wiper operation and streaking on the glass. If you cannot remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer surface of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with water. D If you cannot eliminate the streaking even after following this pro- cedure, replace the wiper blades with new ones. Refer to the “Wiper blade replacement” section (chapter 11) for replacement instruc- tions.

J Windshield wiper and washer switches

B Windshield wipers

To turn the wipers on, push the wiper control lever down.

HB2019BB

: Intermittent LO : Low speed HI : High speed

To turn the wipers off, return the lever to the “OFF” position.

3-22

FORESTER (72F) NA (E) A8040B

Instruments and controls

B Wiper intermittent time control (if equipped)

HB2023BA

When the wiper switch is in the “ the operating interval of the wiper.

” position, turn the dial to adjust

B Mist (for a single wipe) For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever.

B Washer

HB2020BA

To wash the windshield, push the washer button at the end of the wip- er control lever. The washer fluid sprays until you release the washer button. The wipers operate while you push the button.

– CONTINUED –

3-23

FORESTER (72F) NA (E) A8040B

J Rear window wiper and washer switch

(if equipped)

HS3009BA

B Rear wiper To turn the rear wiper on, turn the knob on the end of the wiper control lever to the “ON” position. To turn the wiper off, return the knob on the end of the lever to the “OFF” position.

n Intermittent When the wiper switch is in the the operating interval of the wiper.

position, turn the dial to adjust

” position. The washer fluid sprays until you release the knob.

B Washer To wash the rear window while the rear wiper is operating, turn the knob on the end of the wiper control lever counterclockwise to the “ To wash the rear window when the rear wiper is not in use, turn the knob on the end of the wiper control lever clockwise to the “ ” position. The washer fluid sprays and the wiper operates until you re- lease the knob.

3-24

FORESTER (72F) NA (E) A8040B

Instruments and controls

Windshield wiper deicer (if equipped)

CAUTION

To prevent the battery from being discharged, do not operate the windshield wiper deicer continuously for any longer than neces- sary.

The windshield wiper deicer operates only when the ignition switch is in the “ON” position.

HB2027BB

Before turning on the windshield wiper deicer, remove any snow from the windshield. To turn on the windshield wiper deicer, push the switch. The indicator light located on the switch lights up while the windshield wiper deicer is operating. The windshield wiper deicer will automatically shut off after about 15 min- utes. If the wiper blades have been deiced completely before that time, push the switch to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If deicing is not complete when you restart your vehicle, you have to push the switch to turn the deicer on again.

– CONTINUED –

3-25

FORESTER (72F) NA (E) A8040B

Rear window defogger switch

CAUTION

D Do not use sharp instruments or window cleaner containing abrasives to clean the inner surface of the rear window. They may damage the conductors printed on the window. D To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary.

The rear window defogger operates only when the ignition switch is in the “ON” position.

Indicator light

HS0063

To turn on the defogger, push the switch. To turn it off, push the switch again. The indicator light located on the switch lights up while the rear window defogger is operating. The defogger will automatically shut off after about 15 minutes. If the win- dow clears before that time, push the switch to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the switch to turn it on again.

NOTE If your vehicle is equipped with the outside mirror defogger, the out- side mirror defogger operates while the rear window defogger is

3-26

FORESTER (72F) NA (E) A8040B

Instruments and controls

operating.

Tilt steering wheel

WARNING

Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury.

B Tilt adjustment

HS0134

1. Adjust the seat position. Refer to “Front seat” section (chapter 1). 2. Pull the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Push the lever up to lock the steering wheel in place. 5. Make sure that the steering wheel is securely locked by moving it up and down.

– CONTINUED –

3-27

FORESTER (72F) NA (E) A8040B

Horn

To sound the horn, push the horn pad.

OM-H2736

Mirrors

Always check that the inside and outside mirrors are properly adjusted before you start driving.

J Inside mirror

HB4003BB

The inside mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position. Push it away for the day position. The night position reduces glare from headlights.

3-28

FORESTER (72F) NA (E) A8040B

Instruments and controls

B Compass mirror (if equipped)

HB6019BB

The inside electronic compass mirror has an anti-glare feature which automatically reduces glare coming from headlights of vehicles be- hind you. It also contains a built-in compass. D By pressing and releasing the left button, the automatic dimming function is toggled on or off. When the automatic dimming function is on, the auto dimming indicator light (green) located to the right of the button will illuminate. D By pressing and releasing the right button, the compass display is toggled on or off. When the compass is on, an illuminated compass reading will appear in the lower part of the mirror.

Even with the mirror in anti-glare mode, the mirror surface turns bright if the transmission is shifted into reverse. This is to ensure good rear- ward visibility during reversing.

– CONTINUED –

3-29

FORESTER (72F) NA (E) A8040B

n Photosensors

HB6020BA

The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded. For this reason, use care not to cover the sensors with stickers, or other simi- lar items. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator.

n Compass calibration 1. For optimum calibration, switch off all nonessential electrical ac- cessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metallic objects or structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the left button for 3 seconds then release, and the compass will enter the calibration mode. “CAL” and direction will be displayed. 4. Drive slowly in a circle until “CAL” disappears from the display (about two or three circles). 5. The compass is now calibrated. Further calibration is not required. The compass will automatically calibrate from this point forward.

3-30

FORESTER (72F) NA (E) A8040B

Instruments and controls

n Compass zone adjustment

HB6021AB

1. The zone setting is factory preset to Zone 8. Refer to the “Com- pass calibration zone” map shown above or one attached to the end of this manual to verify that the compass zone setting is correct for your geographical location. 2. Press and hold the right button for 3 seconds then release, and the word “ZONE” will briefly appear and then the zone number will be dis- played. 3. Press the right hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the correct zone setting for your location is displayed. 4. Releasing the button for 3 seconds will exit the zone setting mode.

J Outside mirrors

WARNING

Objects look smaller in a convex mirror (passenger side) and far- ther away than when viewed in a flat mirror. Do not use the con- vex mirror to judge the distances of vehicles behind you when changing lanes. Use the inside mirror (or glance backwards) to determine the actual size and distance of objects that you view in the convex mirror.

– CONTINUED –

3-31

FORESTER (72F) NA (E) A8040B

HS0065

B Remote control mirror switch (if equipped) The remote control mirrors operate only when the ignition switch is in the “ON” or “ACC” position.

HS3008BB

1. Press either end of the selection switch, “L” for the left and “R” for the right. 2. Move the direction control switch in the direction you want to move the mirror. 3. Return the selection switch to the neutral position to prevent unintentional operation.

The mirrors can also be adjusted manually.

3-32

FORESTER (72F) NA (E) A8040B

Instruments and controls

B Outside mirror defogger (if equipped)

CAUTION

To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary.

The outside mirror defogger shares the switch with rear window defogger.

The outside mirror defogger operates only when the ignition switch is in the “ON” position.

Indicator light

HS0063

To turn on the outside mirror defogger, push the switch. To turn it off, push the switch again. The indicator light located on the switch is on while the outside mirror defogger is operation. The defogger will automatically shut off after about 15 minutes. If the mirror clears before that time, push the switch to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the switch to turn it on again.

NOTE While the outside mirror defogger is operating, the rear window defogger also operates

– CONTINUED –

3-33