Login- Download PDF Manual
-
– CONTINUED –
3-35
Climate control
Ventilator ....................................................... Air flow selection .............................................. Center and side ventilators .............................. Manual climate control system .................... Control panel ..................................................... Heater operation ............................................... Air conditioner operation (if equipped) ..........
Automatic climate control system
4-2
4-2
4-3
4-4
4-4
4-6
4-9(if equipped) ............................................... 4-10
4-16
Temperature sensors .......................................Operating tips for heater and air
conditioner ................................................. 4-17
Cleaning ventilation grille ................................ 4-17
Efficient cooling after parking in directsunlight ...........................................................
Lubrication oil circulation in the refrigerant
circuit ..............................................................
Checking air conditioning system before
summer season .............................................. Cooling and dehumidifying in high humidity and low temperature weather conditions ....
Air conditioner compressor shut-off when
4-17
4-17
4-17
4-18
engine is heavily loaded ................................ Refrigerant for your climate control system ..
4-18
4-18
Air filtration system (if equipped) ................ 4-18
4-19Replacing an air filter .......................................
4-1
Climate control
Climate controlVentilator
Air flow selection
4-2
HS4008BA
Center and side ventilators (cid:0) Center ventilators
(cid:0) Side ventilators
Climate control
HS4009BA
1) Open 2) Close
HS4010BB
Move the tab up and down or right and left to adjust the flow direction.
Move the tab up and down or right and left to adjust the flow direction. To open or close the ventilator, turn the thumb-wheel up or down.
– CONTINUED –
4-3
Climate control
Manual climate control system
Control panel
HS4011BB
1) Temperature control dial 2) Fan speed control dial 3) Air flow control dial 4) Rear window defogger button (Refer to the “Rear win-
dow defogger switch” in chapter 3.) 5) Air conditioner button (if equipped) 6) Air inlet selection button
(cid:0) Temperature control dial This dial regulates the temperature of air flow from the air outlets over a range from the blue side (cool) to red
4-4
side (warm). (cid:0) Fan speed control dial The fan operates only when the ignition switch is turned to the “ON” position. The fan speed control dial is used to select four fan speeds. (cid:0) Air flow control dial This dial has the following five positions:
: Air flows through the instrument panel outlets.
: Air flows through the instrument panel outlets and
the foot outlets.
: Air flows through the foot outlets and some
through the windshield defroster outlets.
: Air flows through the windshield defroster outlets
and foot outlets.
: Air flows through the windshield defroster outlets.
NOTE ” po- When the dial is placed in the “ sition, the air conditioner compressor operates automatically regardless of the position of the air conditioner button to defog the windshield quick- ly. However the indicator on the air conditioner
” or “
Climate control
will come on.
Push it again to turn off the air conditioner. (cid:0) Air inlet selection button
button will not come on. At the same time, the air inlet selection is automatically set to “outside air” mode. In this state, you cannot select “recirculation” mode by manually pressing the air inlet selection button. Also, you cannot stop the air conditioner com- pressor by pressing the air conditioner button. (cid:0) Air conditioner button (if equipped)
HS4012BA
The air conditioner operates only when the engine is running.
Push the air conditioner button while the fan is in op- eration to turn on the air conditioner. The indicator light
HS4012CA
ON position (Recirculation): Interior air is recirculat- ed inside the vehicle. Push the air inlet selection but- ton to the ON position. The indicator light will come on. Place the air inlet selection button to the ON position for fast cooling with the air conditioner or when driving on a dusty road. OFF position (Outside air): Outside air is drawn into the passenger compartment. Push the air inlet selec- tion button again to the OFF position. The indicator
– CONTINUED –
4-5
Climate control
light will go off. Place the air inlet selection button to the OFF position when the interior has cooled to a comfortable temper- ature and the road is no longer dusty.
Heater operation (cid:0) Defrosting or defogging the windshield
Continued operation with the air inlet selection button in the ON position may fog up the win- dows. Switch to the OFF position as soon as the outside dusty condition clears.
HS4013AA
To direct warm air to the windshield and front door win- dows: 1. Set the air flow control dial to the “ ” position. 2. Turn the temperature control dial all the way to the right. 3. Set the fan speed control dial to the highest speed.
If your vehicle is equipped with an air conditioner, when the “ ” position is selected, the air conditioner compressor automatically operates re- gardless of the position of the air conditioner button to
” or “
4-6
defog the windshield quickly. However, the air conditioner indicator light does not come on at this time. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel down. (cid:0) Heating and defrosting
Climate control
” or “
If your vehicle is equipped with an air conditioner, when the “ ” position is selected, the air conditioner compressor automatically operates re- gardless of the position of the air conditioner button to defog the windshield quickly. However, the air conditioner indicator light does not come on at this time. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel down. (cid:0) Heating
HS4014AA
To direct warm air toward the floor and the windshield: 1. Set the air flow control dial to the “ 2. Set the temperature control dial to the most com- fortable level. 3. Set the fan speed control dial to the desired speed.
”position.
To direct warm air toward the floor:
HS4015AA
– CONTINUED –
4-7
Climate control
” position.
1. Set the air inlet selection button to the OFF position 2. Set the air flow control dial to the “ 3. Set the temperature control dial to the most com- fortable level. 4. Set the fan speed control dial to the desired speed. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel down. (cid:0) Bi-level heating
air from the foot outlets is slightly warmer than from the instrument panel outlets. 1. Set the air inlet selection button to the OFF posi- tion. 2. Set the air flow control dial to the “ 3. Set the temperature control dial to the desired tem- perature level. 4. Set the fan speed control dial to the desired speed.
” position.
Setting the temperature control dial fully turned to the red area or blue area decreases the temperature dif- ference between the air from the instrument panel out- lets and the air from the foot outlets. (cid:0) Ventilation
This setting allows you to direct air of different temper- atures from the instrument panel and foot outlets. The
HS4016AA
4-8
HS4017AA
To force outside air through the instrument panel out- lets: 1. Set the air inlet selection button to the OFF posi- tion. 2. Set the air flow control dial to the “ 3. Set the temperature control dial all the way left. 4. Set the fan speed control dial to the desired speed.
” position.
When driving on a dusty road, set the air inlet selection button to the “ON” position.
Continued operation with the air inlet selection button in the ON position may fog up the win- dows. Switch to the OFF position as soon as the outside dusty condition clears.
Climate control
Air conditioner operation (if equipped) (cid:0) Cooling or dehumidifying
HS4018BB
1) ON position
For cooling and dehumidification of the passenger compartment, performing the following steps will allow air to flow through the instrument panel outlets: 1. Set the air inlet selection button to the OFF posi- tion. ” position. 2. Set the air flow control dial to the “ 3. Set the air conditioner button to the “ON” position. 4. Set the temperature control dial to the blue side. 5. Set the fan speed control dial at the highest speed.
– CONTINUED –
4-9
Climate control
(cid:0) Defrosting or defogging
HS4013AA
To direct warm air to the windshield and front door win- dows: 1. Set the air flow control dial to the “ 2. Set the temperature control dial to the red side. 3. Set the fan speed control dial at the highest speed.
” position.
The air conditioner compressor automatically oper- ates when the air flow control dial set in the “ ” or “ ” position to provide better defogging perfor- mance. However, the air conditioner indicator light does not come on at this time.
4-10
Automatic climate control system (if equipped)
NOTE Operate the automatic climate control system when the engine is running. When the engine coolant is cold, the blower does not run. In the “AUTO” mode, when the air temperature in the passenger compartment is sufficiently cool, the air conditioner compressor does not operate. For efficient defogging or dehumidifying in cold weather, press the “A/C” switch on. Even when cooling is not necessary, setting the temperature much lower than the current outlet air temperature turns on the air conditioner compres- sor automatically and the “A/C” indicator light on the control panel comes on.
The automatic climate control system automatically controls outlet air temperature, fan speed, air flow dis- tribution air-inlet control, and air conditioner compres- sor operation. It activates when the “AUTO” switch is pressed, and is used in conjunction with the Temper- ature control dial to maintain a constant, comfortable climate within the passenger compartment. The temperature can be set within a range of 65° –
Climate control
85° F (18° – 32° C). NOTE The temperature is shown in units of Fahrenheit for the US model and in Centigrade for the Canadi- an model. (cid:0) Control panel
dow defogger switch” in chapter 3.)
8) Air inlet selection switch 9) OFF/BRIGHT switch
(cid:0) AUTO switch AUTO mode operation:
US4032BB
1) Temperature control dial 2) AUTO switch 3) Fan speed control dial 4) Air conditioner switch 5) Air flow control dial 6) Defroster switch 7) Rear window defogger switch (Refer to the “Rear win-
When the “AUTO” switch is pressed, the indicator light on the switch illuminates, indicating that the Automatic Climate Control system is operating in the automatic mode. In the automatic mode, the system maintains the desired cabin air temperature (this is set using the temperature control dial) by automatically controlling the fan speed, air flow mode, air inlet selection, and air conditioner compressor operation.
US4031BA
– CONTINUED –
4-11
” or “
” position.
If you wish to dim the illumination again, hold down the OFF switch again or if you can safely do so, turn the light switch OFF and then place it in the “ (cid:0) Temperature control dial This dial is used to set the desired interior tempera- ture. With the dial set to your desired temperature, the system automatically adjusts the temperature of air supplied from the outlets such that the desired temper- ature is achieved and maintained. If the dial is turned fully counterclockwise, the system gives maximum cooling performance. If the dial is turned fully clockwise, the system gives maximum heating performance. NOTE The temperature is shown in units of Fahrenheit for the US model and in Centigrade for the Canadi- an model.
Climate control
Manual mode operation: If you operate any of the switches and dials on the control panel other than the “OFF” switch and temper- ature control dial during automatic mode operation, the indicator light on the “AUTO” switch goes out. You can then manually control the system as desired using the switch or dial you operated. To change the system back to the AUTO mode, press the “AUTO” switch. (cid:0) OFF switch The Automatic Climate Control system turns off (the air conditioner compressor and fan turn off) when the “OFF” switch is pressed. When the “OFF” switch is pressed, the outside air in- troduction mode (air inlet selection OFF) is automati- cally selected. NOTE Display (BRIGHT): Setting the light switch to the “ ” position causes the illumination on the display panel to dim. When traveling with the lights on in gloomy daylight or in twilight, press the OFF switch for 1 second or longer if you feel it is too hard to identify the illumination clearly. The bright- ness comes back to normal.
illumination
cancellation
dimness
” or “
4-12
(cid:0) — Defroster switch
Climate control
the system to the setting that was selected before you activated the defroster. (cid:0) Fan speed control dial
HS4021CA
To defrost or dehumidify the windshield and side win- dows, push the defroster switch “ ”. When the “ ” switch is pushed, regardless whether the air conditioner is operating or not, outside air is drawn into the passenger compartment, the air conditioner com- pressor turns on, air flow is directed towards the wind- shield and side windows, and the indicator light on the switch comes on. After eliminating the fogging from the windshield, re- turn the climate control system to the AUTO mode by pushing the “AUTO” switch or turn off by pushing the “OFF” switch. Alternatively, push the “
” switch again to return
HS4020AA
The fan operates only when the ignition switch is in the “ON” position. Select any of the four fan speeds by turning the fan speed control dial. The selected fan speed is indicated by illumination of the corresponding indicator light around the dial.
– CONTINUED –
4-13
Climate control
(cid:0) A/C — Air conditioner switch
(cid:0) Air flow control dial
HS4020DA
HS4021AA
If the windshield starts to fog when the climate control system is operated in the AUTO mode, push the air conditioner switch “A/C” to defog and dehumidify. When this switch is pushed, the air conditioner com- pressor turns on and the indicator light comes on. Af- ter eliminating the fogging from the windshield, set the system back to the AUTO mode by pushing the “AU- TO” switch. NOTE The air conditioner compressor does not operate when the outside air temperature is below 32° F (0° C).
Select the desired air flow mode by turning the air flow control dial. The selected air flow mode is indicated by illumination of the corresponding indicator light around the dial.
(Ventilation): Air flows through the instrument panel
outlets.
(Bi-level): Air flows through the instrument panel
outlets and the foot outlets.
(Heat): Air flows through the foot outlets and some
through the windshield defroster outlets.
4-14
(Heat-def): Air flows through the windshield de-
froster outlets and foot outlets. (cid:0) Air inlet selection switch
HS4020CA
”.
Select air flow by pushing the air inlet selection switch “ ON (Recirculation): Interior air recirculates inside the passenger compartment. Push the air inlet selection button to the ON position for fast cooling with the air conditioner or when driving on a dusty road. The indi- cator light comes on when the “Recirculation” mode is selected. OFF (Outside air): Outside air is drawn into the pas- senger compartment. Push the air inlet selection but-
Climate control
ton to the OFF position when the interior has cooled to a comfortable temperature and the road is no longer dusty. When the climate control system is operated in the “AUTO” mode, this position is selected automati- cally. The indicator light goes off when the “Outside air” mode is selected.
Continued operation in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears.
– CONTINUED –
4-15
Climate control
Temperature sensors
The sensors are located as follows: – Solar sensor: beside the windshield defroster grille – Interior air temperature sensor: near the steering column – Ambient temperature sensor: behind the front grille.
HS4028BB
1) Interior air temperature sensor 2) Solar sensor
The automatic climate control system employs several sensors. These sensors are delicate. If they are not treated properly and become damaged, the system may not be able to control the interior temperature cor- rectly. To avoid damaging the sensors, observe the following precautions: – Do not subject the sensors to impact. – Keep water away from the sensors. – Do not cover the sensors.
4-16
Operating tips for heater and air con- ditioner
Cleaning ventilation grille
HS4022CA
Always keep the front ventilation inlet grille free of snow, leaves, or other obstructions to ensure efficient heating and defrosting. Since the condenser is located in front of the radiator, this area should be kept clean because cooling performance is impaired by any ac- cumulation of insects and leaves on the condenser.
Climate control
Efficient cooling after parking in direct
sunlight
After parking in direct sunlight, drive with the windows open for a few minutes to allow outside air to circulate into the heated interior. This results in quicker cooling by the air conditioner. Keep the windows closed during the operation of the air conditioner for maximum cool- ing efficiency.
Lubrication oil circulation in the refrig-
erant circuit
Operate the air conditioner compressor at a low en- gine speed (at idle or low driving speeds) a few min- utes each month during the off-season to circulate its oil.
Checking air conditioning system be-
fore summer season
Check the air conditioner unit for refrigerant leaks, hose conditions, and proper operation each spring. This check is best performed by your SUBARU dealer.
– CONTINUED –
4-17
Air filtration system (if equipped)
If your vehicle’s air conditioning system is equipped with an air filtration system, replace the filter element according to the replacement schedule shown below. This schedule should be followed to maintain the fil- ter’s dust collection ability. Under extremely dusty con- ditions, the filter should be replaced more frequently. It is recommended that you have your filter checked or replaced by your SUBARU dealer. For replacement, use only a genuine SUBARU air filter kit.
Replacement schedule:
Every 12 months or 7,500 miles (12,000 km) whichev- er comes first
Climate control
Cooling and dehumidifying in high hu-
midity and low temperature weather conditions
Under certain weather conditions (high relative humid- ity, low temperatures, etc.) a small amount of water vapor emission from the air outlets may be noticed. This condition is normal and does not indicate any problem with the air conditioning system.
Air conditioner compressor shut-off
when engine is heavily loaded
To improve acceleration and gas mileage, the air con- ditioner compressor is designed to temporarily shut off during air conditioner operation whenever the acceler- ator is fully depressed such as during rapid accerela- tion or when driving on a steep upgrade.
Refrigerant for your climate control
system
Your air conditioner uses ozone friendly refrigerant HFC134a. Therefore, the method of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.
4-18
Replacing an air filter
Climate control
1. Remove the glove box.
1)Open the glove box. 2)Remove the nine screws securing the glove box.
2. Remove the air filter cover.
HS4024BA
1) Air filter cover
HS4025BB
– CONTINUED –
4-19
Climate control
HS4026BB
HS4025CB
1) Air filter element 2) Arrow mark
3. Replace the air filter element with new one.
1) Air filter cover
4. Reinstall the air filter cover.
The arrow mark on the filter must point UP.
4-20
Climate control
5. Reinstall the glove box. 6. Close the glove box.
1) Service label 2) Caution label
HS4024BA
HS4027BB
7. LABEL installation
1)Fill out the information on the service label (small). 2)Attach service and caution labels on the door pil- lar on the driver’s side.
Contact your dealer if the following occurs, even if it is not yet time to change the filter: – Reduction of the air flow through the vents.
– CONTINUED –
4-21
Climate control
– Windshield gets easily fogged or misted.
NOTE The filter can influence the air conditioning, heat- ing and defroster performance if not properly maintained.
4-22
Audio
Antenna system ............................................ FM reception ..................................................... Installation of accessories ........................... Audio set ........................................................ Type A audio set ............................................... Type B audio set ............................................... In-dash 6 CD auto changer (Optional audio
unit – if equipped) .......................................... Type A audio set (if equipped) ..................... Radio operation ................................................ Compact disc player operation ....................... CD changer control (If optional in-dash CD
5-2
5-2
5-3
5-3
5-3
5-45-4
5-5
5-5
5-10changer is connected) ...................................
5-13
Type B audio set (if equipped) ..................... 5-16
5-16
5-22
In-dash 6 CD auto changer (if equipped) .... 5-27
5-27Radio operation ................................................ Built-in CD changer operation .........................
Loading and unloading compact discs ..........
Precautions to observe when handling
a compact disc (CD) .................................. 5-30
5-1
Audio
AudioAntenna system
FM reception Although FM is normally static free, reception can be affected by the surrounding area, atmospheric condi- tions, station strength and transmitter distance. Build- ings or other obstructions may cause momentary stat- ic, flutter or station interference. If reception continues to be unsatisfactory, switch to a stronger station.
The antenna is printed on the inside of the left side rear quarter window glass.
HS5008BA
Do not use sharp instruments or window clean- er containing abrasives to clean the inner sur- face of the window on which the antenna is printed. Doing so may damage the antenna printed on the window.
5-2
Installation of accessories
Audio set
Always consult your SUBARU dealer before installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrectly in- stalled or if they are not suited for the vehicle.
Your SUBARU may be equipped with one of the fol- lowing audio sets. See the pages indicated in this sec- tion for operating details.
Type A audio set
Audio
Radio operation: refer to page 5-5
Compact disc player operation: refer to page 5-10
CD changer control: refer to page 5-13HS5009AA
– CONTINUED –
5-3
Audio
Type B audio set
In-dash 6 CD auto changer (Optional
audio unit – if equipped)
Radio operation: refer to page 5-16
Built-in CD changer operation: refer to page 5-22US5020AA
Inserting and removing a disc or all discs: refer to page 5-27
HG5021AA
5-4
Type A audio set (if equipped)
The radio will operate only when the ignition switch is in the “ACC” or “ON” position.
Radio operation
(1)
(2)
Audio
(1) Power switch, Volume control, Tone/Fader/Balance control dial
(2) BAND button (3) Tuning buttons (4) Preset buttons (5) AUDIO button (6) SCAN button
(6)
(5)
(4)
(3)
HS5012BB
– CONTINUED –
5-5
Audio
(cid:0) Power switch and volume/bass/treble/fader/
balance control (PWR/VOL)
The dial (1) is used for both power (ON/OFF) and vol- ume control. The radio is turned ON and OFF by push- ing the dial and the volume is controlled by turning the dial. (cid:1) Tone and balance control The “VOLUME” control knob normally function as vol- ume control. This knob become a control for Treble, Bass, Fader or Balance when you select the appropri- ate audio mode. Choose desired volume level for each mode by turning the “VOLUME” control knob. The control function re- turns to volume control mode after about 5 seconds. To change control modes: Each brief press of the “AUDIO” button changes control modes in the follow- ing sequence starting from volume control mode. (When the radio is first turned on, the control mode is in the volume control.)
Volume (VOL)
Bass (BAS)
Treble (TRE)
Balance (BAL) Fader (FAD)
5-6
Display
Control mode
Audio
Turn counterclockwise
Turn clockwise
HS5014BA
BAS
TRE
BAL
FAD
VOL
Bass control
For less bass
Treble control
For less treble
For more bass
For more treble
Balance control
Fader control
To increase left speaker volume and decrease right speaker volume
To increase right speaker volume and decrease left speaker volume
To increase rear speaker volume and decrease front speaker volume
To increase front speaker volume and decrease rear speaker volume
Volume control
For less volume
For more volume
– CONTINUED –
5-7
Audio
(cid:0) FM/AM/Weather band selection button (BAND) Push the “BAND” button when the radio is on to select FM1, FM2, AM or Weather band (WB) reception. Each time this button is pressed, the band will change in the following order:
FM1
FM2
AM
WB
The display indicates which one is currently selected. (cid:0) Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received. (cid:0) Tuning (TUNE) (cid:1) Manual tuning (TUNE) Push the tuning button (3) marked “ ” to increase the tuning frequency and press the tuning button marked “ Each time the button is pressed, the frequency chang- es 10 KHz in the AM waveband and 0.2 MHz in the FM waveband. (cid:1) Manual tuning for weather band When weather band mode is selected, press the tun-
” to decrease it.
5-8
” to change the WB chan- ing button (3) marked “ nel up and press the tuning button marked “ ” to change the WB channel down. Each time the button is pressed, the WB channel changes to the next chan- nel. (cid:0) Seek tuning If the tuning button (3) is pressed for longer than half of a second, the radio will begin to automatically search for receivable frequencies and will stop at the first one found. This function may not be available, however, when radio signals are weak. In such a situ- ation, perform manual tuning to select the desired sta- tion. (cid:0) Automatic tuning (SCAN) Press the “SCAN” button (6) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while displaying the fre- quency, after which scanning will continue until the en- tire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tun- ing, stations are scanned in the direction of low fre- quencies to high frequencies only.
Automatic tuning may not function properly if the sta- tion reception is weakened by distance from the sta- tion or proximity to tall buildings and hills. (cid:0) Selecting preset stations Presetting a station with a preset button (4) allows you to select that station in a single operation. Up to six WB, AM, FM1 and FM2 stations each may be preset. (cid:0) How to preset stations 1. Press the “BAND” selection button to select AM, FM1, FM2 or WB reception. 2. Press the “SCAN” button (6) or tune the radio man- ually until the desired station frequency is displayed. 3. Press one of the preset buttons (4) for at least 2
seconds to store the frequency. At this time, there will momentarily be no sound from the radio. If the button is pressed for less than 2 seconds, the preceding se- lection will remain in memory. NOTE If the connection between the radio and battery is broken for any reason such as vehicle mainte- nance or radio removal, all stations stored in the preset buttons are cleared. If this occurs, it is nec- essary to reset the preset buttons. If a mobile telephone is placed near the radio, it may cause the radio to emit noise when it receivescalls. This noise does not indicate a radio fault.
Audio
– CONTINUED –
5-9
Audio
Compact disc player operation
(15)
(7)
(8) (9)
(7) Disc slot (8) CD button (9) Eject button (10) Fast forward and track up button (11) Fast reverse and track down
button
(12) Random button (13) Repeat button (14) Scan button (15) PWR (power) switch
(14)
(13)
(12)
(11)
(10)
HS5012CB
5-10
(cid:0) To play back a compact disc (cid:1) When CD is not in the player Hold a disc with a finger in the center hole while grip- ping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatical- ly pull the disc into position. A single CD (8 cm/3 inch CD) may also be used with- out any adapter. NOTE Make sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the player might shut off. After the last song finishes, the player will auto- matically return to track 1 (the first song on the disc). (cid:1) When CD is in the player Press the “CD” button (8). The display will show “CD” and the player will start playback. NOTE After the last song finishes, playback will automat- ically return to track 1 (the first song on the disc). (cid:0) To stop playback of a CD When the “PWR” button (15) is pressed during play-
Audio
back of a CD, the CD stops playing temporarily. To let the CD resume playing, press the button again. (cid:0) To select a song from its beginning (cid:1) Forward direction Briefly press the “ ” button (10) to skip to the be- ginning of the next track. Each time the button is pressed, the indicated track number will increase. (cid:1) Backward direction Briefly press the “ ” button (11) to skip to the be- ginning of the current track. Each time the button is pressed, the indicated truck number will decrease. (cid:0) Fast forwarding and fast reverse (cid:1) Fast forwarding Press the “ than 1 second to fast forward the disc. Release the button to stop fast forwarding. (cid:1) Fast reverse Press the “ than 1 second to fast reverse the disc. Release the button to stop fast reverse. (cid:0) Repeat playback Press the “RPT” button (13) and release it in less than
” button (10) continuously for more
” button (11) continuously for more
– CONTINUED –
5-11
The disc may be removed even when the ignition switch is in the “LOCK” position. NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out. To protect the disc, the disc is automatically loaded if it is left in the ejected position for more than approximately 15 seconds (Auto Reload). In this case, the disc is not played.
Audio
2 seconds while a song is playing to play the song re- peatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indica- tor goes out, and normal playback mode is restored. (cid:0) Random playback Press the “RAND” button (12) and hold it in for more than 2 seconds while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal play- back mode is restored. (cid:0) Scan Press the “SCAN” button (14) and release it in less than 2 seconds, and you can hear the first 10 seconds of each track to search for the desired program. To continue listening to the program, press the “SCAN” button again. After all tracks on the disc has been scanned, normal playback mode is restored. (cid:0) To eject a disc from the player When a disc is being played back or when a disc is in the player, press the eject button “ ” (7). The disc will be ejected.
5-12
CD changer control (If optional in-dash CD changer is
connected)
An optional CD changer can be connected to this audio unit. Consult the instructions that accompany the CD changer for operating the CD changer itself (e.g., how to load or unload CDs). See your SUBARU dealer for more information.
(16) CD button (17) Track selection buttons (18) RAND (Random) button (19) RPT (Repeat) button (20) SCAN button
(16)
Audio
(20)
(19)
(18)
(17)
HS5012DB
– CONTINUED –
5-13
Audio
(cid:0) To start playback When the “CD” button (16) is pressed, the CD changer will start playback. The display shows the current disc number, track number and the elapsed time during playback. NOTE If a disc is in the player, the “DISC” button is used to change from CD player operation to DISC changer operation. Each time the “DISC” button is pressed, the operating mode will change alter- nately. At the end of the disc, the player automatically continues with the next disc. After playback on the last disc finishes, play- back will automatically return to the first disc. If you have loaded fewer than 6 discs, any miss- ing disc is automatically skipped. (cid:0) Selection of a desired disc You can select a desired disc from among the discs contained in the CD changer only by pressing the cor- responding number on one of the disc select buttons. If you are to listen to the 5th disc in the CD changer, press the “5” button of the disc select buttons. All other discs in the CD changer can also be selected in a sim- ilar way.
5-14
NOTE No disc change takes place if the button corre- sponding to the storage tray in which no disc is loaded is pressed. If the disc select button corresponding to the disc now in playback is pressed again, the disc will be replayed from its beginning. (cid:0) To select a song from its beginning (cid:1) Forward direction Briefly press the “ ” button (17) to skip to the be- ginning of the next track. Each time the button is pressed, the indicated track number will increase. (cid:1) Backward direction Briefly press the “ ” button (17) to skip to the be- ginning of the current track. Each time the button is pressed, the indicated track number will decrease. (cid:0) Fast forwarding and fast reverse (cid:1) Fast forwarding Press the “ than 1 second to fast forward the disc. Release the button to stop fast forwarding. If you continue fast forwarding to the end of the disc, the CD changer will automatically stop fast forwarding and start playback beginning with the first track on the
” button (17) continuously for more
” button (17) continuously for more
current disc. (cid:1) Fast reverse Press the “ than 1 second to fast reverse the disc. Release the button to stop fast reverse. If you continue fast reverse to the beginning of the disc, the CD changer will automatically stop fast re- verse and start playback beginning with the first track on the current disc. (cid:0) Repeat Press the “RPT” button (19) while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. (cid:0) Random playback Press the “RAND” button (18) while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal play- back mode is restored.
Audio
(cid:0) Scan (a convenient way to become familiar with
a disc)
1. Press the “SCAN” button (20).
– The display shows “SCAN” and the track number being scanned. – You hear the first 10 seconds of each track. – The operation is automatically cleared after play- ing all programs. Then, normal playback starts.
2. Press the “SCAN” button again when you hear a track you like.
– Normal playback resumes.
(cid:0) To stop playback To stop playback and switch over to the radio mode, press the “BAND” button.
– CONTINUED –
5-15
Audio
Type B audio set (if equipped)
The radio will operate only when the ignition switch is in the “ACC” or “ON” position.
Radio operation
(1) (2) (3)
(4)
(5)
(6)
(1) SCAN button (2) FM/AM selection button (3) WB (weather band) button (4) Power switch, Volume control, Bass/Middle/Treble control and Fader/Balance control dial
(5) TONE button (6) Fader/Balance selection button (7) Preset buttons (8) Tuning buttons
(8)
(7)
US5021BB
5-16
(cid:0) Power switch and volume/bass/treble/fader/
balance control (PWR/VOL)
The dial (4) is used for both power (ON/OFF) and vol- ume control. The radio is turned ON and OFF by push- ing the dial and the volume is controlled by turning the dial.
This dial is used for bass/middle/treble controls when the “TONE” button (5) is in the depressed position. It is also used for fader/balance controls when the “BAL” button (6) is in the depressed position.
Audio
– CONTINUED –
5-17
Audio
Display
Control mode
Turn counterclockwise
Turn clockwise
HS5014BA
BASS
MIDDLE
TREBLE
FADER
Bass control
For less bass
For more bass
Middle note control
For less middle note
For more middle note
Treble control
For less treble
For more treble
Fader control
To increase rear speaker volume and decrease front speaker volume
To increase front speaker volume and decrease rear speaker volume
BALANCE
Balance control
To increase left speaker volume and decrease right speaker volume
To increase right speaker volume and decrease left speaker volume
VOLUME
Volume control
For less volume
For more volume
5-18
(cid:1) Tone control The volume control dial (4) normally function as vol- ume control. The dial become a control for Bass, Mid- dle note or Treble when you select the appropriate tone control mode. Choose desired level for each mode by turning the vol- ume control dial. The control function returns to vol- ume control mode after about 5 seconds. To change control modes: Each brief press of the “TONE” button (5) changes control modes in the fol- lowing sequence starting from bass control mode. (When the radio is first turned on, the control mode is in the volume control.)
BASS
MIDDLE
TREBLE
VOLUME
(cid:1) Fader and balance control The volume control dial (4) normally function as vol- ume control. The dial become the controls for Fader or Balance when you select the appropriate fader and balance control mode. Choose desired setting for each mode by turning the volume control dial. The control function returns to vol- ume control mode after about 5 seconds. To change control modes: Each brief press of the
Audio
“BAL” button (6) changes control modes in the follow- ing sequence starting from fader control mode. (When the radio is turned on, the control mode is in the vol- ume control.)
FADER
BALANCE
VOLUME
(cid:1) Display illumination dimness cancellation
(BRIGHT)
” or “
” or “
The brightness of the radio display dims when the light switch is in the “ ” positions. If this makes the display difficult to read, press the volume dial for more than 1.5 seconds to return the display to original brightness. Subsequently pressing the volume dial again for more than 1.5 seconds or if you can safely do so, turning the light switch to the OFF position and back to the “ ” position makes the radio display dim again. (cid:0) FM/AM selection button (FM/AM) Push the “FM/AM” button (2) when the radio is off to turn on the radio. Push the “FM/AM” button when the radio is on to se- lect FM1, FM2 or AM reception. Each time this button is pressed, the band will change in the following order: – CONTINUED –
5-19
Audio
FM1
FM2
AM
The display indicates which one is currently selected. (cid:0) Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received. (cid:0) Weather band button (WB) Push the “WB” button (3) when the radio is off to turn on the radio in the weather band. Press the “WB” button when the radio is on to select the weather band. (cid:0) Manual tuning (TUNE) (cid:1) Manual tuning for AM and FM waveband Push the tuning button (8) marked “ ” to increase the tuning frequency and press the tuning button marked “ Each time the button is pressed, the frequency chang- es 10 KHz in the AM waveband and 0.2 MHz in the FM waveband. (cid:1) Manual tuning for weather band When weather band mode is selected, press the tun-
” to decrease it.
5-20
” to change the WB channel ing button (8) marked “ up and press the tuning button marked “ ” to change the WB channel down. Each time the button is pressed, the WB channel changes to the next chan- nel. (cid:0) Seek tuning If the tuning button (8) is pressed for longer than half of a second, the radio will begin to automatically search for receivable frequencies and will stop at the first one found. This function may not be available, however, when radio signals are weak. In such a situ- ation, perform manual tuning to select the desired sta- tion. (cid:0) Automatic tuning (SCAN) Press the “SCAN” button (1) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while displaying the fre- quency, after which scanning will continue until the en- tire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tun- ing, stations are scanned in the direction of low fre- quencies to high frequencies only.
Automatic tuning may not function properly if the sta- tion reception is weakened by distance from the sta- tion or proximity to tall buildings and hills. (cid:0) Selecting preset stations Presetting a station with a preset button (7) allows you to select that station in a single operation. Up to six AM, FM1, FM2 and WB stations each may be preset. (cid:0) How to preset stations 1. Press the “FM/AM” selection button to select AM, FM1 or FM2 reception.
Press the “WB” button (3) to select the weather band.
OR
2. Press the “SCAN” button (1) or tune the radio man- ually until the desired station frequency is displayed. 3. Press one of the preset buttons (7) for at least 1.5
seconds to store the frequency. The frequency of the station will flash once on the display at this time. If the button is pressed for less than 1.5 seconds, the pre- ceding selection will remain in memory. NOTE If the connection between the radio and battery is broken for any reason such as vehicle mainte- nance or radio removal, all stations stored in the preset buttons are cleared. If this occurs, it is nec-Audio
essary to reset the preset buttons. If a mobile telephone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio fault.
– CONTINUED –
5-21
Audio
Built-in CD changer operation
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(9) Eject button (10) SCAN button (11) CD (CD player selection) button (12) Disc slot (13) DISC indicator (14) Repeat button (15) Random button (16) LOAD button (17) Disc select buttons (18) Track selection buttons
(18)
(17)
US5021CB
5-22
NOTE Make sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the player might shut off. Single CDs (i.e., 8-cm/3-inch CDs) are not sup- ported, and if inserted, they will be immediately ejected. If a disc is inserted during a radio broadcast, the disc will interrupt the broadcast. (cid:0) How to insert a CD(s) (cid:1) Inserting a CD 1. Press “LOAD” button (16). If the magazine in the player has an idle position where you can insert a disc, the “DISC” indicator (13) associated with the idle posi- tion will blink. If no indicator blinks, it means that there is no idle po- sition in the magazine. 2. As soon as the “DISC” indicator (13) begins to blink, the “LOAD” will appear on display for a period of 15 seconds. Insert a disc during the period. The disc will be then automatically drawn in, and the player will begin to play back the first number of the disc.
To insert more discs in succession, repeat Steps 1
and 2. The magazine will be loaded with discs in theAudio
ascending order of position number. If you do not insert any disc in 15 seconds after you have pressed the “LOAD” button, the player will begin to play back the first number of the last disc you have inserted. The disc indicator steadily lights up if a disc is al- ready inserted in the corresponding position of the magazine. While the player is in the loading mode, if you press the “FM/AM” selection button (2), the player will enter the standby mode. Press the “CD” button (11) to start playback. (cid:1) Inserting a disc in a desired position 1. Press the “LOAD” button (16). If the magazine in the player has an idle position where you can insert a disc, the “DISC” indicator (13) associated with the idle position will blink. The positions in the magazine the indicator of which steadily lights up are already loaded with discs. 2. Press the “DISC SELECT” button (17) at the posi- tion where you want to insert a disc. The associated “DISC” indicator will blink, and the “LOAD” will be dis- played. 3. If you insert a disc during the 15-second period while the “LOAD” is on display, the disc will be auto- matically drawn in, and the player will start playback of the disc, beginning with the first number.
– CONTINUED –
5-23
Audio
To insert more discs in succession, repeat Steps 1
and 2. While the player is in the loading mode, if you press the “FM/AM” selection button (2), the player will enter standby mode. Press the “CD” button (11) to start playback. (cid:1) Loading all the magazine (Full disc loadingmode)
1. If you continue to press the “LOAD” (16) button for more than 1.5 seconds, the player will produce beep sound and will enter the full disc loading mode. 2. A “DISC” indicator (13) will blink, and the “ALL LOAD” will be on display for a period of 15 seconds. If a disc is successfully loaded during this period, the “DISC” indicator will stop blinking and will steadily light. 3. When the loading of a disc is complete, the next “DISC” indicator will blink. Then repeat Step 2. 4. When the magazine is filled with discs by repeating Steps 2 and 3, the player will start playback of the discs, beginning with the one inserted first. If you fail to insert any disc during each 15-second in- terval, the full disc loading mode will be canceled, and the player will start playback of the disc inserted first.
5-24
(cid:0) How to play back a CD or make a pause (cid:1) When there is no CD inserted: Insert a CD by referring to “How to insert a CD(s)”. When a CD is loaded, the player will start playback of the CD, beginning with the first number. (cid:1) When there are CDs loaded: Press a desired one of the “DISC SELECT” buttons (17) the “DISC” indicator (13) of which steadily lights up. The player will then start playback of the selected CD, beginning with the first number. (cid:0) To select a song from its beginning (cid:1) Forward direction Briefly press the “ ” button (18) to skip to the begin- ning of the next track. Each time the button is pressed, the indicated track number will increase. (cid:1) Backward direction Briefly press the “ ” button (18) to skip to the begin- ning of the current track. Each time the button is pressed, the indicated truck number will decrease. (cid:0) Fast forwarding and fast reverse (cid:1) Fast forwarding Press the “
” button (18) continuously for more than
” button (18) continuously for more than
0.5 second to fast forward the disc. Release the button to stop fast forwarding. (cid:1) Fast reverse Press the “ 0.5 second to fast reverse the disc. Release the button to stop fast reverse. (cid:0) Repeat playback Press the “RPT” button (14) while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. (cid:0) Random playback Press the “RDM” button (15) while a disc is being played back to play all songs on the disc in a random order. The “RDM” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RDM” indicator goes out, and normal play- back mode is restored. (cid:0) Scan When the “SCAN” button (10) is pressed while the disc is being played back, you can hear the first 10 seconds
Audio
of each track to seach for the desired program. To continue listening to the program, press the “SCAN” button again. After all tracks on the disc have been scanned, normal playback mode is restored. (cid:0) How to unload CDs from the player (cid:1) Ejecting a CD from the player Of the discs loaded, you can select and remove only one disc. 1. Press the “DISC SELECT” button (17) of the disc whose “DISC” indicator (13) is ON. 2. Press the “EJECT” button (9). Then the “DISC” in- dicator associated with the disc you have selected will blink, and the disc will be ejected. To remove more discs in succession, repeat Steps 1
and 2. If you press the “EJECT” button after turning OFF the ignition switch, only one disc will be ejected. (cid:1) Ejecting all discs from the player (All disc ejec-tion mode)
1. If you continue to press the “EJECT” button (9), the player will produce beep sound and will enter the all disc ejection mode. 2. Remove the disc that has been ejected. The other discs loaded will then be ejected one after another. If you do not remove the ejected disc within 15 seconds,
– CONTINUED –
5-25
Audio
the all disc ejection mode will be canceled. NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.
Do not attempt to insert two or more discs into the slot at a time. Doing so can cause mechan- ical damage to the CD changer.
5-26
In-dash 6 CD auto changer (if equipped)
Loading and unloading compact discs
(5)
(1)
(2)
Audio
(1) Disc slot (2) Disc indicators (disc No.1 to 6) (3) Disc select buttons (disc No.1 to
6)
(4) Eject button (5) Disc slot indicator
(4)
(3)
HG5022BB
– CONTINUED –
5-27
Audio
mark.
identified by
Do not attempt to insert two or more discs into the slot at a time. Doing so can cause me- chanical damage to the CD changer. Use only music CDs Do not use CDs listed below which could cause damage to the CD player. 3-inch (8 cm) compact disc. Any disc with a peel-off or seal on it. Any disc with scratches and/or dust. Bent disc. Cleaning disc. CD accessory. (E.g., 3-inch (8 cm) disc adapter)
Do not insert or remove any disc when the automatic transmission selector lever is in the park position; the selector lever in that position can interfere with disc insertion or removal, causing scratches on the disc surface (for AT vehicles).
(cid:0) To insert a disc 1. Press one of the “Disc select” buttons (3) (num- bered from 1 to 6) for which the disc indicator light (2)
5-28
is “OFF”. The Disc indicator lights are located directly above the corresponding “Disc select” buttons. 2. The indicator will begin blinking. The blinking will last for 15 seconds. During this period, insert a desired disc, and the disc will begin to play. (If any disc is not inserted during this period, the “Disc slot” (1) door will close. Repeat step 1.) Be sure to hold a disc with the label side (the side where titles are printed) up. 3. To insert another disc, repeat step 1 and 2 choos- ing a different disc select button. (cid:0) To insert six discs at a time 1. Press and hold the “Disc select” button number 1
until all disc indicators begin blinking (about 1.5 sec- onds). 2. The indicators will blink for 15 seconds. During this period, insert desired six discs. 3. When all discs are loaded, the first disc will begin to play. (If no disc is inserted within this 15 seconds, the entire disc load sequence will be canceled.) (cid:0) To remove a disc 1. Press the desired one of the “Disc select” buttons (3) (numbered from 1 to 6) for which the disc indicator light is on.2. Press the “Eject button” (4). The selected disc will be ejected and the indicator light will begin blinking. 3. To remove another disc, repeat step 1 and 2
choosing a different “Disc select” button. (To remove discs when the ignition switch is in the “Lock” position, press the “Eject” button, and the first disc will be ejected. Press the “Eject” button again, and the next disc will be ejected and so on. At this time, the “Disc select” buttons are disabled.) (cid:0) To remove all discs at one time 1. Press and hold the “Eject” button (4) until all “Disc” indicators begin blinking (about 1.5 seconds), and the first disc will be ejected. 2. When the disc is removed, the next one will be ejected, and so on. (cid:0) To replace a playing disc with another Simply press the desired one of “Disc select” buttons (3) (numbered from 1 to 6) or press the “DISC select” button on the radio unit to select the desired disc, and the disc will begin to play. (cid:0) Disc indicators Lit: when the corresponding storage tray is occupied by a disc. Blinking: Disc player is either in loading, eject or changing mode.Audio
OFF: No disc is loaded or the ignition switch is in the “LOCK” position. (cid:1) Open/Closed disc slot indicator When the disc slot is open, the disc indicators on both sides of the slot illuminate. (cid:0) Function control Refer to CD changer control operating instructions de- scribed in the “Type A audio set (if equipped)” section.
– CONTINUED –
5-29
To remove a disc from the case, press the center of the case and hold both edges of the disc. If the disc surface is touched directly, contamination could cause poor tone quality. Do not touch the disc surface. Use a clean disc whenever possible. If there are de- posits, wipe the disc surface from the center outward with a dry, soft cloth. Be sure not to use a hard cloth, thinner, benzene, alcohol, etc. Do not use any disc that is scratched, deformed, or cracked. Also, do not use any disc that has a non-stan- dard shape (for example, a heart shape). Malfunctions or problems might result. A disc is vulnerable to heat. Never keep it either in places exposed to direct sunlight, near heaters or in vehicles parked in the sun or hot days.
Audio
Precautions to observe when han- dling a compact disc (CD)
HS5017AA
Use only compact discs (CDs) that have the mark shown above. CD-RWs cannot be used. Also, some CD-Rs cannot be played. In cold and/or rainy weather, dew can form inside the CD player, preventing normal operation. If this happens, eject the CD and wait for the player to dry out. Skipping may occur when the CD player is subject- ed to severe vibration (for example, when the vehicle is driven on a rough surface).
5-30
Audio
– CONTINUED –
5-31
HS5018BA
Interior lights ................................................ Dome light ......................................................... Cargo area light ................................................ Map lights ...................................................... Sun visors ..................................................... Vanity mirror ...................................................... Storage compartments ................................ Glove box ........................................................... Center console .................................................. Overhead console ............................................. Dashboard storage compartment ................... Convenience net ............................................... Coin tray ............................................................ Cup holders .................................................. Front passenger’s cup holder ......................... Rear passenger’s cup holder ........................... Accessory power outlets ............................. Cigarette lighter socket ................................ Use with a cigarette lighter .............................. Using as an accessory power outlet ............... Ashtray .......................................................... Floor mat ....................................................... Coat hook ...................................................... Cargo area cover (if equipped) .................... Using the cover ................................................. To remove the cover ......................................... To install the cover housing ............................ Shopping bag hook ...................................... Cargo tie-down hooks ..................................
6-2
6-2
6-2
6-3
6-3
6-4
6-4
6-5
6-5
6-6
6-6
6-7
6-7
6-8
6-8
6-8
6-9
6-11
6-12
6-13
6-14
6-15
6-16
6-16
6-16
6-17
6-17
6-18
6-18Interior equipment
Under-floor storage compartment ............... 6-19
6-1
Interior equipment
Interior equipment
Interior lights
When leaving your vehicle, make sure the light goes out to avoid battery discharge.
The light also can be turned on by use of the keyless entry transmitter. See the “Remote keyless entry sys- tem (if equipped)” in chapter 2 for detailed information. OFF: The light stays off.
Dome light
Cargo area light
ON
DOOR
OFF
ON
OFF DOOR
HS6025BB
HS6026BB
The dome light switch has three positions: ON: The light stays on continuously. DOOR (middle position): The dome light comes on when any of the doors or the rear gate is opened. The light remains on for several seconds and gradually goes out after all doors and the rear gate are closed or if the key is inserted in the ignition switch.
6-2
The cargo area light switch has three positions: ON: The light stays on continuously. OFF: The light stays off. DOOR: The light comes on only when the rear gate is opened.
Map lights
Sun visors
Interior equipment
HS6027BA
HS6028BA
To turn on the map light, push the switch. To turn it off, push the switch again.
When leaving the vehicle, make sure the light is turned off to avoid battery discharge.
To block out glare, swing down the visors. To use the sun visor at a side window, swing it down and move it sideways.
– CONTINUED –
6-3
Storage compartments
Always keep the storage compartment closed while driving to reduce the risk of injury in the event of sudden stops or an accident. Do not store spray cans, containers with flammable or corrosive liquids or any other dangerous items in the storage compartment.
Interior equipment
Vanity mirror
To use the vanity mirror, swing down the sun visor and open the vanity mirror cover.
HS6029BA
6-4
Glove box
Center console
Interior equipment
HS6030BB
1) Lock 2) Unlock
To open the glove box, pull the handle. To close it, push the lid firmly upward.
To lock the glove box, insert the key and turn it clock- wise.
HS6031BA
To open the lid, pull up the lock release. If the console lid is fully opened when a large cup is put in the rear passenger’s cup holder, the lid may hit the cup and beverage may be spilled.
– CONTINUED –
6-5
Interior equipment
Overhead console
Dashboard storage compartment
To open the console, push on the console lid lightly and the lid will automatically open.
To open the dashboard compartment, push the button on the lid and the lid will automatically open. Be sure to close the compartment fully before driving.
HS6052BA
HS6053BA
When your vehicle is in the sun or a warm day, the inside of the overhead console heats up. Avoid storing plastic or other heat-vulnerable or flammable articles such as a lighter in the overhead console.
6-6
Convenience net
Coin tray
Interior equipment
A net for storing small articles is provided at the front passenger’s foot-well.
To open the coin tray, pull the upper edge of the lid.
HS6054AA
HS6055BA
– CONTINUED –
6-7
Interior equipment
Cup holders
Front passenger’s cup holder
Rear passenger’s cup holder
