Login- Download PDF Manual
-
cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position.
Do not turn the ignition switch to the “START” position while the engine is running.
Key reminder chime The reminder chime sounds when the driver’s door
– CONTINUED –
3-3
Instruments and controls
opens and the key is in the “LOCK” or “ACC” positions. The chime stops when the key is removed from the ig- nition switch.
Key interlock release (AT vehicles
only)
If the key can not be turned to the “LOCK” position even when the selector lever is in the “P” position: 1. Take out the screwdriver from the tool bag.
2. Remove the cover under the steering column using a phillips screwdriver.
HS3016BA
3-4
HS3017BA
3. Turn the ignition key while pressing the key inter- lock release lever. Take your vehicle to the nearest SUBARU dealer im- mediately to have the key interlock system repaired.
Hazard warning flasher
Meters and gauges
Instruments and controls
Speedometer The speedometer shows the vehicle speed.
Odometer/Trip meter
HS3020BB
1) Trip meter 2) Odometer
This meter displays the odometer and two trip meters when the ignition switch is in the “LOCK”, “ACC” or “ON” position.
– CONTINUED –
3-5
HS3019BA
The hazard warning flasher is used to warn other driv- ers when you have to park your vehicle under emer- gency conditions. The hazard warning flasher works with the ignition switch in any position.
To turn on the hazard warning flasher, push the haz- ard warning button on the instrument panel. To turn off the flasher, push the button again. NOTE When the hazard warning flasher is on, the turn signals do not work.
Instruments and controls
T Odometer The odometer shows the total distance that the vehicle has been driven. T Double trip meter
A trip meter
B trip meter
To set the trip meter to zero, select the A trip or B trip meter by pushing the knob and keep the knob pushed for more than 2 seconds.
HS3021BB
1) A trip meter 2) B trip meter
The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the knob. Each press of the knob changes the function alter- nately.
3-6
To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result.
NOTE If the connection between the combination meter and battery is broken for any reason such as vehi- cle maintenance or fuse replacement, the data re- corded on the trip meter will be lost.
Tachometer The tachometer shows the engine speed in thousands of revolutions per minute.
Do not operate the engine with the pointer of the tachometer in the red zone. In this range,
fuel injection will be cut by the engine control module to protect the engine from overrevving. The engine will resume running normally after the engine speed is reduced below the red zone.
The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank. NOTE
Instruments and controls
Fuel gauge
HS3022BB
1) Low fuel warning light
The fuel gauge shows the approximate amount of fuel remaining in the tank. The gauge does not return to “E” even though the ig- nition switch is in the “ACC” or “LOCK” position.
HS3023AA
You will see the “FUEL DOOR ” sign near the fuel gauge. This indicates that the fuel filler door (lid) is locat- ed on the right side of the vehicle. T Low fuel warning light The low fuel warning light comes on when the tank is nearly empty [about 2.3 U.S. gal. (9.0 liters, 1.9 Imp. gal.]. It only operates when the ignition switch is in the “ON” position.
– CONTINUED –
3-7
Instruments and controls
NOTE This light does not go out unless the tank is re- plenished up to an internal fuel quantity of about 4.0 U.S. gal. (15 liters, 3.3 Imp. gal.).
Temperature gauge
We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. Engine operation is optimum with the engine coolant at this temperature range and high revving operation when the engine is not warmed up enough should be avoided.
If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possi- ble. See “In case of emergency” in chapter 9.
HS3024BB
1) Normal operating range
The temperature gauge shows engine coolant temper- ature when the ignition switch is in the “ON” position.
The coolant temperature will vary in accordance with the outside temperature and driving conditions.
3-8
Ambient temperature gauge
Warning and indicator lights
Instruments and controls
HS3047BA
The ambient temperature gauge shows the ambient temperature in a range from –22° F to 122° F (–30° C to 50° C). The gauge can give a false reading under any of the following conditions: y When there is too much sun. y During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately follow- ing a shutdown. y When the actual ambient temperature falls outside the specified indicator range.
Several of the warning and indicator lights come on momentarily and then go out when the ignition switch is initially turned to the “ON” position. This permits checking the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position. The following lights come on:
Seatbelt warning light SRS airbag system warning light CHECK ENGINE warning light/Malfunction indica- tor lamp Charge warning light Oil pressure warning light AT OIL temperature warning light (AT vehicles) ABS warning light Brake system warning light
If any lights fail to come on, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer for repair.
Seatbelt warning light and chime When the ignition switch is turned to the “ON” position, the seatbelt warning light will come on and the remind- er chime will sound for about six seconds to remind the
– CONTINUED –
3-9
Instruments and controls
driver to fasten the seatbelt. The seatbelt warning light remains on for about six seconds and turns off automatically after six seconds. The seatbelt reminder chime will turn off by bucking the driver’s side seatbelt or turn off automatically after six seconds.
SRS airbag system warning light When the ignition switch is turned to the “ON” position, the SRS airbag system warning light will come on for about six seconds and go out. This shows the SRS air- bag and SRS side airbag (if equipped) and seatbelt pretensioners are in normal operation. If this light comes on while driving or remains illuminat- ed even after a period of about 6 seconds from when the ignition has been turned on, it may indicate that the SRS airbag system or SRS side airbag system (if equipped) or seatbelt pretensioner system is not work- ing properly. Contact your nearest SUBARU dealer immediately.
3-10
CHECK ENGINE warning light/
Malfunction indicator lamp
If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possible. Continued vehicle operation without having the emission control system checked and repaired as necessary could cause serious damage, which may not be covered by your vehicle’s warranty.
If this light comes on steadily or blinks while the engine is running, it may indicate that there is a problem or po- tential problem somewhere in the emission control system. T If the light comes on steadily: If the light comes on steadily while driving or does not go out after the engine starts, an emission control sys- tem malfunction has been detected. You should have your vehicle checked by an autho- rized SUBARU dealer immediately.
NOTE This light also comes on when the fuel filler cap is not tightened until it clicks.
If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indica- tor lamp coming on could be a loose or missing fuel fill- er cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK EN- GINE warning light turn off immediately. It may take several driving trips. If the light does not go out, take your vehicle to your authorized SUBARU dealer im- mediately. T If the light is blinking: If the light is blinking while driving, an engine misfire condition has been detected which may damage the emission control system. To prevent serious damage to the emission control system, you should do the following: y Reduce vehicle speed. y Avoid hard acceleration. y Avoid steep uphill grades. y Reduce the amount of cargo, if possible. y Stop towing a trailer as soon as possible. The CHECK ENGINE warning light may stop blinking
Instruments and controls
and come on steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately.
Charge warning light If this light comes on when the engine is run- ning, it may indicate that the charging system is not working properly.
If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the alternator belt. If the belt is loose, broken or if the belt is in good condition but the light remains on, contact your nearest SUBARU deal- er immediately.
Oil pressure warning light If this light comes on when the engine is run- ning, it may indicate that the engine oil pressure is low and the lubricating system is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil lev- el is low, add oil immediately. If the engine oil is at the proper level but the light remains on, contact your nearest SUBARU dealer immediately.
– CONTINUED –
3-11
Instruments and controls
Do not operate the engine with the oil pressure warning light on. This may cause serious en- gine damage.
AT OIL TEMPerature warning
light (for AT vehicles)
If this light comes on when the engine is running, it may indicate that the automatic transmission fluid tem- perature is too hot.
If the light comes on while driving, it is unnecessary to stop the vehicle, but avoid driving up steep grades or in stop and go traffic. T Automatic transmission control system warn-
ing
If the light flashes after the engine starts, it may indi- cate that the automatic transmission control system is not working properly. Contact your nearest SUBARU dealer for service immediately.
(U.S.) ABS warning light (Canada) The ABS warning light comes on when the ignition
3-12
switch is turned to the “ON” position and goes out after about two seconds. This is an indication that the ABS system is working properly.
If the warning light behaves as follows, the ABS system may not work properly. When the warning light is on, the ABS function shuts down; however, the conventional brake system continues to operate normally. y The warning light does not come on when the ignition switch is turned to the “ON” position. y The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8 mph (12 km/h). y The warning light comes on during driving. If these occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer.
With a vehicle equipped with an EBD system, the ABS warning light comes on together with the brake system warning light if the EBD system becomes faulty. For
further details of the EBD system fault warning, refer to “Brake system warning light”. NOTE If the warning light behavior is as shown below, the ABS system may be considered normal. y The warning light comes on right after the en- gine is started but goes out immediately, remain- ing off. y The warning light remains on after the engine has been started, but it goes out when the vehicle speed reaches about 8 mph (12 km/h). y The warning light comes on during driving, but it goes out immediately and remains off.
When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning light may come on. This is due to the low battery volt- age and does not indicate a malfunction. When the battery becomes fully charged, the light will go out.
Brake system warning light
(U.S.) (Canada)
y Driving with the brake system warning light on is dangerous. This indicates your brake sys-
Instruments and controls
tem may not be working properly. If the light re- mains on, have the brakes inspected by a SUBARU dealer immediately. y If at all in doubt about whether the brakes are operating properly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for repair.
This light has the following three functions: T Parking brake warning The light comes on with the parking brake applied while the ignition switch is in the “ON” position. It goes out when the parking brake is fully released. T Brake fluid level warning This light comes on when the brake fluid level has dropped to near the “MIN” level of the brake fluid res- ervoir with the ignition switch in the “ON” position and with the parking brake fully released.
If the brake system warning light should come on while driving (with the parking brake fully released and with the ignition switch positioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. If this occurs, immediately stop the vehicle at the near- est safe place and check the brake fluid level. If the flu-
– CONTINUED –
3-13
Instruments and controls
id level is below the “MIN” mark in the reservoir, do not drive the vehicle. Have the vehicle towed to the near- est SUBARU dealer for repair. T Electronic Brake Force Distribution (EBD) sys-
tem warning (for vehicles with EBD)
The brake system warning light also illuminates if a malfanction occurs in the EBD system. In that event, it comes on together with the ABS warning light. The EBD system may be faulty if the brake system warning light and ABS warning light illuminate simulta- neously during driving. Even if the EBD system fails, the conventional braking system will still function. However, the rear wheels will be more prone to locking when the brakes are applied harder than usual and the vehicle’s motion may there- fore become somewhat harder to control. If the brake system warning light and ABS warning light take the following steps: 1. Stop the vehicle in the nearest safe, flat place. If you cannot avoid parking the vehicle on a slope, use chocks to prevent the vehicle from moving. 2. Shut down the engine, then restart it. 3. Release the parking brake. If both warning lights go out, the system is normal and no further action is nec- essary. 4. If both warning lights come on again and stay illu-
illuminate simultaneously,
3-14
minated after the engine has been restarted, shut down the engine again, apply the parking brake, and check the brake fluid level. 5. If the brake fluid level is not below the “MIN” mark, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspect- ed. 6. If the brake fluid level is below the “MIN” mark, DO NOT drive the vehicle. Instead, have the vehicle towed to the nearest SUBARU dealer for repair.
Door open warning lights The door open warning light comes on if any door or the rear gate is not fully closed.
Always make sure this light is out before you start to drive.
Low fuel warning light The low fuel warning light comes on when the tank is nearly empty about 2.3 U.S. gal. (9.0 liters, or 1.9 Imp. gal.). It only operates when the ignition switch is in the “ON” position. NOTE This light does not go out unless the tank is re- plenished up to an internal fuel quantity of about
4.0 U.S. gal. (15 liters, 3.3 Imp. gal.).
Front-wheel drive warning light
(for AT vehicles)
This light comes on when All Wheel Drive is disen- gaged and the drive mechanism is switched to Front Wheel Drive for maintenance or similar purposes.
Shift position indicator (AT vehicles) This indicator shows the position of the shift lever.
Turn signal indicator lights These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to the “Replacing bulbs” section in chapter 11.
High beam indicator light This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated.
Instruments and controls
Cruise control indicator light This light comes on when the “CRUISE” main switch is pressed.
– CONTINUED –
3-15
Instruments and controls
Clock
To adjust the clock, open the small article storage compartment in the dashboard with the vehicle parked in a safe place.
HS3025BA
To set the hour, press the “H” button. To set the min- utes, press the “M” button. To reset the minutes to “00” with a radio time signal, push the “Reset” button.
HS3018BA
To ensure safety, do not attempt to set the time while driving, as an accident from inadequate attention to the road could result.
3-16
Light control switch
Headlights
The light switch operates only when the ignition switch is in the “ON” position.
Instruments and controls
To prevent battery discharge resulting from ac- cidentally leaving your lights on when your ve- hicle is parked, the light switch operates only when the ignition switch is in the “ON” posi- tion. In any other position, the vehicle’s lights will be out. If you park your vehicle on a roadside at night, use the hazard warning flasher to alert the other drivers.
HS3026BA
To turn on the headlights, turn the knob on the end of the turn signal lever.
first position
Parking lights, instrument panel illumination, tail lights and license plate light are on.
second position
Headlights, parking lights, instrument panel illumina- tion, tail lights, and license plate light are on.
– CONTINUED –
3-17
Instruments and controls
High/low beam change (dimmer)
Headlight flasher
HS3026CA
HS3026DA
To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indicator light “ ” on the in- strument panel is also on. To switch back to low beam, pull the lever back to the detent position.
To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the lighting switch is in the “OFF” posi- tion.
When the headlights are on high beam, the high beam indicator light “ ” on the instrument panel also comes on.
Do not hold the lever in the flashing position for
3-18
more than just a few seconds.
Turn signal lever
Instruments and controls
Daytime running light system
The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switch must always be turned to the “ ” position when it is dark outside.
The low beam headlights will automatically come on at reduced brightness when the engine has started, un- der the following conditions: y The parking brake is fully released. y The light switch is in the “OFF” or “ ” position. y The automatic transmission selector lever is set at other than the “P” position.
1) Right turn 2) Left turn 3) Lane change for right 4) Lane change for left
HS3027BB
To activate the right turn signal, push the turn signal le- ver up. To activate the left turn signal, push the turn signal lever down. When the turn is finished, the lever will return automatically. If the lever does not return af- ter cornering, return the lever to the neutral position by hand.
To signal a lane change, push the turn signal lever up – CONTINUED –
3-19
Instruments and controls
or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction of the turn or lane change. The lever will return auto- matically to the neutral position when you release it.
Illumination brightness control
HS3028BA
” When the lighting switch is in the “ position, you can adjust brightness of the instrument panel illumination for better visibility. To brighten, turn the control dial upward. To darken, turn the control dial downward.
” or “
3-20
Parking light switch
Fog light switch (if equipped)
Instruments and controls
HS3029BA
HS3030AA
The parking light switch operates regardless of the ig- nition switch position.
By pushing the front end of this switch, following lights will come on. – Parking lights – Tail lights – License plate lights
To turn off, push the rear end of the parking light switch. Avoid leaving these lights on for a long time because that will run down the battery.
The fog lights operate only when the headlights are on low beam. Push the fog light switch to turn the fog lights on. Press the switch again to turn them off. The indicator light located on the switch will illuminate when the fog lights are on.
– CONTINUED –
3-21
Instruments and controls
Wiper and washer
In freezing weather, do not use the windshield washer until the windshield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view.
y Do not operate the washer continuously for more than ten seconds, or when the washer flu- id tank is empty. This may cause overheating of the washer motor. Check the washer fluid level frequently, such as at fuel stops. y Do not operate the wipers when the wind- shield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the windshield washer. y In freezing weather, be sure that the wiper blades are not frozen to the windshield or rear window before switching on the wipers. At-
3-22
tempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper motor to burn out. If the wiper blade is frozen to the window glass, be sure to oper- ate the defroster, windshield wiper deicer (if equipped) or rear window defogger before turn- ing on the wiper. y If the wipers stop during operation because of ice or some other obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper operation. y Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. (See the “Windshield washer fluid” section in chapter 11.) Also, when driving the vehicle when there are freezing temperatures, use non-freezing type wiper blades. y Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzene. This will cause deterioration of the wiper
blades.
NOTE y The wiper operates only when the ignition switch is in the “ON” or “ACC” position. y Clean your wiper blades and window glass peri- odically with a washer solution to prevent streak- ing, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the windshield or rear window. y Grease, wax, insects or other material on the windshield or the wiper blade results in jerky wip- er operation and streaking on the glass. If you can- not remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer surface of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with wa- ter. y If you cannot eliminate the streaking even after following this procedure, replace the wiper blades with new ones. Refer to the “Replacement of wind-
Instruments and controls
shield wiper blades” section (chapter 11) for re- placement instructions.
Windshield wiper and washer switches T Windshield wipers
HS3031BB
1) OFF 2) : Intermittent 3) LO: Low speed 4) HI: High speed
To turn the wipers on, push the wiper control down. To turn the wipers off, return the lever to the “OFF” po-
lever
– CONTINUED –
3-23
Instruments and controls
sition. T Wiper intermittent time control (if equipped)
T Mist (for a single wipe)
For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever.
HS3033BA
HS3032BA
When the wiper switch is in the “ the dial to adjust the operating interval of the wiper.
” position, turn
The operating interval can be adjusted continuously from the shortest interval to the longest. Two click stop positions of the dial may help you to aim at your desired interval.
3-24
T Washer
Rear window wiper and washer switch
Instruments and controls
HS3033CA
To wash the windshield, push the washer button at the end of the wiper control lever. The washer fluid sprays until you release the washer button. The wipers oper- ate while you push the button.
ONON INTINT O F F
R E A R R E A R
HS3034BB
1) INT 2) ON 3) Washer T Rear wiper To turn the rear wiper on, turn the knob on the end of the wiper control lever upward.
INT: Intermittent ON: Normal
To turn the wiper off, return the knob on the end of the lever to the “OFF” position.
– CONTINUED –
3-25
Instruments and controls
T Washer To wash the rear window while the rear wiper is oper- ating, turn the knob on the end of the wiper control le- ver counterclockwise to the “ ” position. The washer fluid sprays until you release the knob. To wash the rear window when the rear wiper is not in use, turn the knob on the end of the wiper control lever clockwise to the “ ” position. The washer fluid sprays and the wiper operates until you release the knob.
3-26
Windshield wiper deicer (if equipped)
HS3045AA
The windshield wiper deicer operates only when the ignition switch is in the “ON” position. Before turning on the windshield wiper deicer, remove any snow from the windshield. To turn on the wind- shield wiper deicer, push the switch. The indicator light located on the switch lights up while the windshield wiper deicer is operating. The windshield wiper deicer will automatically shut off after about 15 minutes. If the wiper blades have been deiced completely before that time, push the switch to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If deicing is
not complete, you have to push the switch to turn the deicer on again.
Rear window defogger switch
Instruments and controls
To prevent the battery from being discharged, do not operate the windshield wiper deicer con- tinuously for any longer than necessary.
NOTE If your vehicle is equipped with the outside mirror defogger, the outside mirror defogger operates while the windshield wiper deicer is operating.
Manual climate control system
HS4012DA
– CONTINUED –
3-27
push the switch again. The indicator light located on the switch lights up while the rear window defogger is operating.
y Do not use sharp instruments or window cleaner containing abrasives to clean the inner surface of the rear window. They may damage the conductors printed on the window. y To prevent the battery from being dis- charged, do not operate the defogger continu- ously for any longer than necessary.
Instruments and controls
HS4021DA
Automatic climate control system
The rear window defogger operates only when the ig- nition switch is in the “ON” position. The rear window defogger switch is located on the cli- mate control panel.
The defogger will automatically shut off after about 15
minutes. If the window clears before that time, push the switch to turn it off. It also turns off when the igni- tion switch is turned to the “ACC” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the switch to turn it on again. To turn on the defogger, push the switch. To turn it off,3-28
Mirrors
T Auto-dimming mirror/compass (if equipped)
Instruments and controls
Always check that the inside and outside mirrors are properly adjusted before you start driving.
Inside mirror
HS3036BB
1) Tab
The inside mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position. Push it away for the day position. The night position reduces glare from headlights.
HS3037BB
1) Left button 2) Auto dimming indicator 3) Photosensor 4) Right button
The inside electronic compass mirror has an anti-glare feature which automatically reduces glare coming from headlights of vehicles behind you. It also con- tains a built-in compass. y By pressing and releasing the left button, the auto- matic dimming function is toggled on or off. When the automatic dimming function is on, the auto dimming in- dicator light (green) located to the right of the button
– CONTINUED –
3-29
Instruments and controls
will illuminate. y By pressing and releasing the right button, the com- pass display is toggled on or off. When the compass is on, an illuminated compass reading will appear in the lower part of the mirror.
Even with the mirror in anti-glare mode, the mirror sur- face turns bright if the transmission is shifted into re- verse. This is to ensure good rearward visibility during reversing. V Photosensors
The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors
HS3038BA
3-30
detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded. For this reason, use care not to cover the sensors with stickers, or other similar items. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator. V Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/ air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metal- lic objects or structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the left button for 3 seconds then re- lease, and the compass will enter the calibration mode. “CAL” and direction will be displayed. 4. Drive slowly in a circle until “CAL” disappears from the display (about two or three circles). 5. The compass is now calibrated. Further calibration is not required. The compass will automatically cali- brate from this point forward.
V Compass zone adjustment
15
14
13
12
11
10
HS3039AA
Compass calibration zones
1. The zone setting is factory preset to Zone 8. Refer to the “Compass calibration zone” map shown above or one attached to the end of this manual to verify that the compass zone setting is correct for your geograph- ical location. 2. Press and hold the right button for 3 seconds then release, and the word “ZONE” will briefly appear and then the zone number will be displayed. 3. Press the right hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the correct zone setting for your location is dis-
Instruments and controls
played. 4. Releasing the button for 3 seconds will exit the zone setting mode.
Outside mirrors
T Convex mirror (passenger side)
HS3040BA
Objects look smaller in a convex mirror and far- ther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes. Use the inside mirror (or glance backwards) to – CONTINUED –
3-31
Instruments and controls
determine the actual size and distance of ob- jects that you view in convex mirror.
3. Return the selection switch to the neutral position to prevent unintentional operation.
T Remote control mirror switch
MIRRMIRROROR
The mirrors can also be adjusted manually. T Outside mirror defogger
HS3041BB
HS3046AB
1) Selection switch 2) Direction control switch
The remote control mirrors operate only when the ig- nition switch is in the “ON” or “ACC” position. 1. Press either end of the selection switch, “L” for the left, “R” for the right. 2. Move the direction control switch in the direction you want to move the mirror.
1) Outside mirror defogger switch (if equipped) 2) Outside mirror defogger and Windshield wiper deicer
switch (if equipped)
The outside mirror defogger operates only when the ignition switch is in the “ON” position. To turn on the outside mirror defogger, push the switch. To turn it off, push the switch again. The indi- cator light located on the switch lights up while the out-
3-32
side mirror defogger is operating.
Tilt steering wheel
Instruments and controls
The defogger will automatically shut off after about 15
minutes. If the mirror clears before that time, push the switch to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If de- frosting or defogging is desired when you restart your vehicle, you have to push the switch to turn it on again. NOTE On vehicles equipped with a windshield wiper de- icer, the windshield wiper deicer switch is also used to operate the outside mirror defogger.To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary.
HS3043BA
1. Adjust the seat position. Refer to the “Front seats” section (chapter 1). 2. Push the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Pull the lever up to lock the steering wheel in place. 5. Make sure that is securely locked by moving it up and down.
the steering wheel
Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle – CONTINUED –
3-33
Instruments and controls
control and result in personal injury.
Horn
To sound the horn, push the horn pad.
HS3044BA
3-34
Climate control
Ventilator ...................................................... Air flow selection ............................................ Center and side ventilators ............................ Manual climate control system ................... Control panel ................................................... Heater operation ............................................. Air conditioner operation (if equipped) ........
Automatic climate control system (if equipped) ................................................. Temperature sensors .....................................
Operating tips for heater and air conditioner ................................................... Cleaning ventilation grille .............................. Efficient cooling after parking in direct sunlight ............................................................ Lubrication oil circulation in the refrigerant circuit ............................................................... Checking air conditioning system before summer season .............................................. Cooling and dehumidifying in high humidity and low temperature weather conditions ..... Air conditioner compressor shut-off when engine is heavily loaded ................................ Refrigerant for your climate control system Air filtration system (if equipped) ............... Replacing an air filter .....................................
4-2
4-2
4-3
4-4
4-4
4-6
4-94-10
4-154-16
4-164-17
4-17
4-17
4-17
4-17
4-17
4-18
4-184-1
Climate control
Climate controlVentilator
Air flow selection
4-2
HS4008BA
Center and side ventilators T Center ventilators
T Side ventilators
Climate control
HS4009BA
1) Open 2) Close
HS4010BB
Move the tab up and down or right and left to adjust the flow direction.
Move the tab up and down or right and left to adjust the flow direction. To open or close the ventilator, turn the thumb-wheel up or down.
– CONTINUED –
4-3
Climate control
Manual climate control system
Control panel
HS4011BB
1) Temperature control dial 2) Fan speed control dial 3) Air flow control dial 4) Rear window defogger button (Refer to the “Rear win-
dow defogger switch” in chapter 3.) 5) Air conditioner button (if equipped) 6) Air inlet selection button T Temperature control dial This dial regulates the temperature of air flow from the air outlets over a range from the blue side (cool) to red
4-4
side (warm). T Fan speed control dial The fan operates only when the ignition switch is turned to the “ON” position. The fan speed control dial is used to select four fan speeds. T Air flow control dial This dial has the following five positions:
: Air flows through the instrument panel outlets.
: Air flows through the instrument panel outlets and
the foot outlets.
: Air flows through the foot outlets and some
through the windshield defroster outlets.
: Air flows through the windshield defroster outlets
and foot outlets.
: Air flows through the windshield defroster outlets.
is placed in the “
NOTE ” or When the dial “ ”position, the air conditioner compressor operates automatically regardless of the position of the air conditioner button to defog the wind- shield quickly. However the indicator on the air
Climate control
will come on.
Push it again to turn off the air conditioner. T Air inlet selection button
conditioner button will not come on. At the same time, the air inlet selection is automatically set to “outside air” mode. In this state, you cannot select “recirculation” mode by manually pressing the air inlet selection button. Also, you cannot stop the air conditioner com- pressor by pressing the air conditioner button. T Air conditioner button (if equipped)
HS4012BA
The air conditioner operates only when the engine is running.
Push the air conditioner button while the fan is in op- eration to turn on the air conditioner. The indicator light
HS4012CA
ON position (Recirculation): Interior air is recirculat- ed inside the vehicle. Push the air inlet selection but- ton to the ON position. The indicator light will come on. OFF position (Outside air): Outside air is drawn into the passenger compartment. Push the air inlet selec- tion button again to the OFF position. The indicator light will go off.
– CONTINUED –
4-5
Climate control
Continued operation with the air inlet selection button in the ON position may fog up the win- dows. Switch to the OFF position as soon as the outside dusty condition clears.
Heater operation T Defrosting or defogging the windshield
1. Set the air flow control dial to the “ ” position. 2. Turn the temperature control dial all the way to the right. 3. Set the fan speed control dial to the highest speed.
” or “
If your vehicle is equipped with an air conditioner, when the “ ” position is selected, the air conditioner compressor automatically operates re- gardless of the position of the air conditioner button to defog the windshield quickly. However, the air conditioner indicator light does not come on at this time. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel down.
To direct warm air to the windshield and front door win- dows:
HS4013AA
4-6
T Heating and defrosting
Climate control
NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel down. T Heating
HS4014AA
To direct warm air toward the floor and the windshield: 1. Set the air flow control dial to the “ 2. Set the temperature control dial to the most com- fortable level. 3. Set the fan speed control dial to the desired speed.
”position.
” or “
If your vehicle is equipped with an air conditioner, when the “ ” position is selected, the air conditioner compressor automatically operates re- gardless of the position of the air conditioner button to defog the windshield quickly. However, the air conditioner indicator light does not come on at this time.
HS4015AA
To direct warm air toward the floor: 1. Set the air inlet selection button to the OFF position 2. Set the air flow control dial to the “ 3. Set the temperature control dial to the most com- fortable level. 4. Set the fan speed control dial to the desired speed.
” position.
– CONTINUED –
4-7
Climate control
NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding thumb-wheel down. T Bi-level heating
perature level. 4. Set the fan speed control dial to the desired speed.
Setting the temperature control dial fully turned to the red area or blue area decreases the temperature dif- ference between the air from the instrument panel out- lets and the air from the foot outlets. T Ventilation
HS4016AA
This setting allows you to direct air of different temper- atures from the instrument panel and foot outlets. The air from the foot outlets is slightly warmer than from the instrument panel outlets. 1. Set the air inlet selection button to the OFF posi- tion. 2. Set the air flow control dial to the “ 3. Set the temperature control dial to the desired tem-
” position.
4-8
HS4017AA
To force outside air through the instrument panel out- lets: 1. Set the air inlet selection button to the OFF posi- tion. 2. Set the air flow control dial to the “ 3. Set the temperature control dial all the way left.
” position.
4. Set the fan speed control dial to the desired speed.
When driving on a dusty road, set the air inlet selection button to the “ON” position.
Air conditioner operation (if equipped) T Cooling or dehumidifying
Climate control
Continued operation with the air inlet selection button in the ON position may fog up the win- dows. Switch to the OFF position as soon as the outside dusty condition clears.
HS4018BB
1) ON position
For cooling and dehumidification of the passenger compartment, air flows through the instrument panel outlets: 1. Set the air inlet selection button to the OFF posi- tion. 2. Set the air flow control dial to the “ ” position. 3. Set the air conditioner button to the “ON” position. 4. Set the temperature control dial to the blue side. 5. Set the fan speed control dial at the highest speed.
– CONTINUED –
4-9
Climate control
T Defrosting or defogging
HS4013AA
To direct warm air to the windshield and front door win- dows: 1. Set the air flow control dial to the “ 2. Set the temperature control dial to the red side. 3. Set the fan speed control dial at the highest speed.
” position.
The air conditioner compressor automatically oper- ates when the air flow control dial set in the “ ” or ” position to provide better defogging perfor- “ mance. However, the air conditioner indicator light does not come on at this time.
4-10
Automatic climate control system (if equipped)
NOTE y Operate the automatic climate control system when the engine is running. y When the engine coolant is cold, the blower does not run. y In the “AUTO” mode, when the air temperature in the passenger compartment is sufficiently cool, the air conditioner compressor does not operate. For efficient defogging or dehumidifying in cold weather, press the “A/C” switch on. y Even when cooling is not necessary, setting the temperature much lower than the current outlet air temperature turns on the air conditioner compres- sor automatically and the “A/C” indicator light on the control panel comes on.
The automatic climate control system automatically controls outlet air temperature, fan speed, air flow dis- tribution air-inlet control, and air conditioner compres- sor operation. It activates when the “AUTO” switch is pressed, and is used in conjunction with the Temper- ature control dial to maintain a constant, comfortable climate within the passenger compartment. The temperature can be set within a range of 65 –
Climate control
85° F (18 – 32° C). NOTE The temperature is shown in units of Fahrenheit for the US model and in Centigrade for the Canadi- an model. T Control panel
dow defogger switch” in chapter 3.)
8) Air inlet selection switch 9) OFF/BRIGHT switch T AUTO switch AUTO mode operation:
HS4019BB
1) Temperature control dial 2) AUTO switch 3) Fan speed control dial 4) Air conditioner switch 5) Air flow control dial 6) Defroster switch 7) Rear window defogger switch (Refer to the “Rear win-
When the “AUTO” switch is pressed, the indicator light on the switch illuminates, indicating that the Automatic Climate Control system is operating in the automatic mode. In the automatic mode, the system maintains the desired cabin air temperature (this is set using the temperature control dial) by automatically controlling the fan speed, air flow mode, air inlet selection, and air conditioner compressor operation.
HS4023BA
– CONTINUED –
4-11
” or “
” position.
If you wish to dim the illumination again, hold down the OFF switch again or if you can safely do so, turn the light switch OFF and then place it in the “ T Temperature control dial This dial is used to set the desired interior tempera- ture. With the dial is set your desired temperature, the system automatically adjusts the temperature of air supplied from the outlets such that the desired temper- ature is achieved and maintained. If the dial is turned fully counterclockwise, the system gives maximum cooling performance. If the dial is turned fully clockwise, the system gives maximum heating performance.
Climate control
Manual mode operation: If you operate any of the switches and dials on the control panel other than the “OFF” switch and temper- ature control dial during automatic mode operation, the indicator light on the “AUTO” switch goes out. You can then manually control the system as desired using the switch or dial you operated. To change the system back to the AUTO mode, press the “AUTO” switch. T OFF switch The Automatic Climate Control system turns off (the air conditioner compressor and fan turn off) when the “OFF” switch is pressed. When the “OFF” switch is pressed, the outside air in- troduction mode (air inlet selection OFF) is automati- cally selected. NOTE Display (BRIGHT): Setting the light switch to the “ ” position causes the illumination on the display panel to dim. When traveling with the lights on in gloomy daylight or in twilight, press the OFF switch for 1 second or longer if you feel it is too hard to identify the illumination clearly. The bright- ness comes back to normal.
cancellation
illumination
dimness
” or “
4-12
T
— Defroster switch
Climate control
the system to the setting that was selected before you activated the defroster. T Fan speed control dial
HS4021CA
To defrost or dehumidify the windshield and side win- dows, push the defroster switch “ ”. When the “ ” switch is pushed, regardless whether the air conditioner is operating or not, outside air is drawn into the passenger compartment, the air conditioner com- pressor turns on, air flow is directed towards the wind- shield and side windows, and the indicator light on the switch comes on. After eliminating the fogging from the windshield, re- turn the climate control system to the AUTO mode by pushing the “AUTO” switch or turn off by pushing the “OFF” switch. Alternatively, push the “
” switch again to return
HS4020AA
The fan operates only when the ignition switch is in the “ON” position. Select any of the four fan speeds by turning the fan speed control dial. The selected fan speed is indicated by illumination of the corresponding indicator light around the dial.
– CONTINUED –
4-13
Climate control
T A/C — Air conditioner switch
T Air flow control dial
HS4020DA
HS4021AA
If the windshield starts to fog when the climate control system is operated in the AUTO mode, push the air conditioner switch “A/C” to defog and dehumidify. When this switch is pushed, the air conditioner com- pressor turns on and the indicator light comes on. Af- ter eliminating the fogging from the windshield, set the system back to the AUTO mode by pushing the “AU- TO” switch. NOTE The air conditioner compressor does not operate when the outside air temperature is below 32° F (0° C).
Select the desired air flow mode by turning the air flow control dial. The selected air flow mode is indicated by illumination of the corresponding indicator light around the dial.
(Ventilation): Air flows through the instrument panel
outlets.
(Bi-level): Air flows through the instrument panel
outlets and the foot outlets.
(Heat): Air flows through the foot outlets and some
through the windshield defroster outlets.
4-14
(Heat-def): Air flows through the windshield de-
froster outlets and foot outlets. T Air inlet selection switch
tem is operated in the “AUTO” mode, this position is selected automatically. The indicator light goes off when the “Outside air” mode is selected.
Climate control
HS4020CA
”.
Select air flow by pushing the air inlet selection switch “ ON (Recirculation): Interior air recirculates inside the passenger compartment. Use this position when quickly cooling down the passenger compartment or to prevent outside air from entering the passenger compartment. The indicator light comes on when the “Recirculation” mode is selected. OFF (Outside air): Outside air is drawn into the pas- senger compartment. When the climate control sys-
Continued operation in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears.
Temperature sensors
HS4028BB
1) Interior air temperature sensor 2) Solar sensor
– CONTINUED –
4-15
Climate control
The automatic climate control system employs several sensors. These sensors are delicate. If they are treat- ed improperly and become damaged, the system may not be able to control the interior temperature correct- ly. To avoid damaging the sensors, observe the follow- ing precautions: – Do not subject the sensors to impact. – Keep water away from the sensors. – Do not cover the sensors.
The sensors are located as follows: – Solar sensor: beside the windshield defroster grille – Interior air temperature sensor: near the steering column – Ambient temperature sensor: behind the front grille.
Operating tips for heater and air con- ditioner
Cleaning ventilation grille
HS4022BA
Always keep the front ventilation inlet grille free of snow, leaves, or other obstructions to ensure efficient heating and defrosting. Since the condenser is located in front of the radiator, this area should be kept clean because cooling performance is impaired by any ac- cumulation of insects and leaves on the condenser.
4-16
Efficient cooling after parking in direct
sunlight
After parking in direct sunlight, drive with the windows open for a few minutes to allow outside air to circulate into the heated interior. This results in quicker cooling by the air conditioner. Keep the windows closed during the operation of the air conditioner for maximum cool- ing efficiency.
Lubrication oil circulation in the refrig-
erant circuit
Operate the air conditioner compressor at a low en- gine speed (at idle or low driving speeds) a few min- utes each month during the off-season to circulate its oil.
Checking air conditioning system be-
fore summer season
Check the air conditioner unit for refrigerant leaks, hose conditions, and proper operation each spring. This check is best performed by your SUBARU dealer.
Climate control
Cooling and dehumidifying in high hu-
midity and low temperature weather conditions
Under certain weather conditions (high relative humid- ity, low temperatures, etc.) a small amount of water vapor emission from the air outlets may be noticed. This condition is normal and does not indicate any problem with the air conditioning system.
Air conditioner compressor shut-off
when engine is heavily loaded
To improve acceleration and gas mileage, the air con- ditioner compressor is designed to temporarily shut off during air conditioner operation whenever the acceler- ator is fully depressed such as during rapid accerela- tion or when driving on a steep upgrade.
Refrigerant for your climate control
system
Your air conditioner uses ozone friendly refrigerant HFC134a. Therefore, the method of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.
– CONTINUED –
4-17
Climate control
Air filtration system (if equipped)
Replacing an air filter
If your vehicle’s air conditioning system is equipped with an air filtration system, replace the filter element according to the replacement schedule shown below. This schedule should be followed to maintain the fil- ter’s dust collection ability. Under extremely dusty con- ditions, the filter should be replaced more frequently. It is recommended that you have your filter checked or replaced by your SUBARU dealer. For replacement, use only a genuine SUBARU air filter kit.
Replacement schedule:
Every 12 months or 7,500 miles (12,000 km) whichev- er comes first
4-18
1. Remove the glove box.
1)Open the glove box. 2)Remove the nine screws securing the glove box.
HS4024BA
Climate control
1) Air filter cover
2. Remove the air filter cover.
HS4025BB
HS4026BB
1) Air filter 2) Arrow mark
3. Replace the air filter with new one.
The arrow mark on the filter must point UP.
– CONTINUED –
4-19
Climate control
1) Air filter cover
4. Reinstall the air filter cover.
HS4025CB
HS4024BA
5. Reinstall the glove box. 6. Close the glove box.
4-20
Climate control
– Windshield gets easily fogged or misted.
NOTE The filter can influence the air conditioning, heat- ing and defroster performance if not properly maintained.
HS4027BB
1) Service label 2) Caution label
7. LABEL installation
the information on the service label
1)Fill out (small). 2)Attach service and caution labels on the door pil- lar on the driver’s side.
Contact your dealer if the following occurs, even if it is not yet time to change the filter: – Reduction of the air flow through the vents.
– CONTINUED –
4-21
Appearance care
Exterior care ................................................. Washing ........................................................... Waxing and polishing ..................................... Cleaning aluminum wheels ............................ Corrosion protection ................................... Most common causes of corrosion .............. To help prevent corrosion ............................. Cleaning the interior .................................... Seat fabric ....................................................... Leather seat materials .................................... Synthetic leather upholstery .........................
10-2
10-2
10-3
10-3
10-4
10-4
10-4
10-5
10-5
10-5
10-610
10-1
Appearance care
Appearance careExterior care
Washing The best way to preserve your vehicle’s beauty is fre- quent washing. Wash the vehicle at least once a month to avoid contamination by road grime.
Wash dirt off with a wet sponge and plenty of luke- warm or cold water. Do not wash the vehicle with hot water and in direct sunlight.
Salt, chemicals, insects, tar, soot and bird droppings should be washed off by using a light detergent, as re- quired. If you use a light detergent, make certain that it is a neutral detergent. Do not use strong soap or chemical detergents. All cleaning agents should be promptly flushed from the surface and not allowed to dry there. Rinse the vehicle thoroughly with plenty of lukewarm water. Wipe the remaining water off with a chamois or soft cloth.
y When washing the vehicle, the brakes may get wet. As a result, the brake stopping dis- tance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes.
10-2
y Do not wash the engine compartment and area adjacent to it. If water enters the engine air intake, electrical parts or the power steering flu- id reservoir, it will cause engine trouble or faulty power steering respectively.
NOTE When having your vehicle washed in an automatic car wash, make sure beforehand that the car wash is of suitable type. Automatic car wash brushes or other equipment may damage the rear wiper and roof spoiler (if equipped). T Washing the underbody Chemicals, salts and gravel used for deicing road sur- faces are extremely corrosive, accelerating the corro- sion of underbody components, such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders, and suspension. Thoroughly flush the underbody and inside of the fenders with lukewarm or cold water at frequent inter- vals to reduce the harmful effects of such agents. T Using a warm water washer y Keep a good distance of 12 in (30 cm) or more be- tween the washer nozzle and the vehicle. y Do not wash the same area continuously.
y If a stain will not come out easily, wash by hand. Some warm water washers are of the high tempera- ture, high pressure type, and they can damage or de- form the resin parts such as mouldings, or cause water to leak into the vehicle.
Waxing and polishing Always wash and dry the vehicle before waxing and polishing. Use a good quality polish and wax and apply them ac- cording to the manufacturer’s instructions. Wax or pol- ish when the painted surface is cool.
Be sure to polish and wax the chrome trim, as well as the painted surfaces. Loss of wax on a painted surface leads to loss of the original luster and also quickens the deterioration of the surface. It is recommended that a coat of wax be applied at least once a month, or whenever the surface no longer repels water.
If the appearance of the paint has diminished to the point where the luster or tone cannot be restored, lightly polish the surface with a fine-grained com- pound. Never polish just the affected area, but include the surrounding area as well. Always polish in only one direction. A No. 2000 grain compound is recom- mended. Never use a coarse-grained compound. Coarser grained compounds have a smaller grain-size
Appearance care
number and could damage the paint. After polishing with a compound, coat with wax to restore the original luster. Frequent polishing with a compound or an in- correct polishing technique will result in removing the paint layer and exposing the undercoat. When in doubt, it is always best to contact your SUBARU deal- er or an auto paint specialist. NOTE Be careful not to block the windshield washer noz- zles with wax when waxing the vehicle.
Cleaning aluminum wheels y Promptly wipe the aluminum wheels clean of any kind of grime or agent. If dirt is left on too long, it may be difficult to clean off. y Do not use soap containing grit to clean the wheels. Be sure to use a neutral cleaning agent, and later rinse thoroughly with water. Do not clean the wheels with a stiff brush or expose them to a high-speed washing device. y Clean the vehicle (including the aluminum wheels) with water as soon as possible when it has been splashed with sea water, exposed to sea breezes, or driven on roads treated with salt or other agents.
– CONTINUED –
10-3
Appearance care
Corrosion protection
proper ventilation.
Your SUBARU has been designed and built to resist corrosion. Special materials and protective finishes have been used on most parts of the vehicle to help maintain fine appearance, strength, and reliable oper- ation.
Most common causes of corrosion The most common causes of corrosion are: 1. The accumulation of moisture retaining dirt and de- bris in body panel sections, cavities, and other areas. 2. Damage to paint and other protective coatings caused by gravel and stone chips or minor accidents.
Corrosion is accelerated on the vehicle when: 1. It is exposed to road salt or dust control chemicals, or used in coastal areas where there is more salt in the air, or in areas where there is considerable industrial pollution. 2. It is driven in areas of high humidity, especially when temperatures range just above freezing. 3. Dampness in certain parts of the vehicle remains for a long time, even though other parts of the vehicle may be dry. 4. High temperatures will cause corrosion to parts of the vehicle which cannot dry quickly due to lack of
10-4
To help prevent corrosion Wash the vehicle frequently. If you drive on salted roads in the winter or if you live in a coastal area, you should flush the underbody with fresh water frequent- ly.
After the winter has ended, it is recommended that the underbody be given a very thorough washing.
Before the beginning of winter, check the condition of underbody components, such as the exhaust system, fuel and brake lines, brake cables, suspension, steer- ing system, floor pan, and fenders. If any of them are found to be rusted, they should be given an appropri- ate rust prevention treatment or should be replaced. Contact your SUBARU dealer to perform this kind of maintenance and treatment if you need assistance.
Repair chips and scratches in the paint as soon as you find them.
Check the interior of the vehicle for water and dirt ac- cumulation under the floor mats because that could cause corrosion. Occasionally check under the mats to make sure the area is dry. Keep your garage dry. Do not park your vehicle in a
damp, poorly ventilated garage. In such a garage, cor- rosion can be caused by dampness. If you wash the vehicle in the garage or put the vehicle into the garage when wet or covered with snow, that can cause damp- ness.
If your vehicle is operated in cold weather and/or in ar- eas where road salts and other corrosive materials are used, the door hinges and locks, trunk lid lock, and hood latch should be inspected and lubricated period- ically.
Appearance care
Cleaning the interior
Use a vacuum cleaner to get rid of the dust and dirt. Wipe the vinyl areas with a clean, damp cloth.
Seat fabric Remove loose dirt, dust or debris with a vacuum cleaner. If the dirt is caked on the fabric or hard to re- move with a vacuum cleaner, use a soft blush then vacuum it. Wipe the fabric surface with a tightly wrung cloth and dry the seat fabric thoroughly. If the fabric is still dirty, wipe using a solution of mild soap and lukewarm water then dry thoroughly.
If the stain does not come out, try a commercially- available fabric cleaner. Use the cleaner on a hidden place and make sure it does not affect the fabric ad- versely. Use the cleaner according to its instructions.
Leather seat materials The leather used by SUBARU is a high quality natural product which will retain its distinctive appearance and feel for many years with proper care. Allowing dust or road dirt to build up on the surface can cause the material to become brittle and to wear pre-
– CONTINUED –
10-5
NOTE Strong cleaning agents such as solvents, paint thinners, window cleaner or gasoline must never be used on leather or synthetic interior materials.
Appearance care
maturely. Regular cleaning with a soft, moist, natural fiber cloth should be performed monthly, taking care not to soak the leather or allow water to penetrate the stitched seams. A mild detergent suitable for cleaning woolen fabrics may be used to remove difficult dirt spots, rubbing with a soft, dry cloth afterwards to restore the luster. If your SUBARU is to be parked for a long time in bright sun- light, it is recommended that the seats and headrests be covered, or the windows shaded, to prevent fading
