2007 Saab 9 7X Owners Manual

Download PDF Manual
or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 5. Press and hold the newly-trained Universal Home Remote button and observe the indicator light. If the indicator light stays on continuously, programming is complete and your device should activate when the Universal Home Remote button is pressed and released. To program the remaining two Universal Home Remote buttons, begin with Step 2 under “Programming Universal Home Remote.” Do not repeat Step 1 as this will erase all of the programmed channels. If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Steps 6 through 8 following to complete the programming of a rolling-code device, most commonly, a garage door opener. 7. Firmly press and release the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8. 8. Return to the vehicle. Firmly press and hold the programmed Universal Home Remote button for two seconds, then release it. Immediately press and hold the same button a second time for two seconds, then release it. Immediately, press and hold the same button a third time for two seconds, then release. The Universal Home Remote should now activate the rolling-code device. To program the remaining two Universal Home Remote buttons, begin with Step 2 of “Programming Universal Home Remote.” Do not repeat Step 1, as this will erase all previous programming from the Universal Home Remote buttons. 137 Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission. This may not be long enough for Universal Home Remote to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to time out in the same manner. If you live in Canada, or you are having difficulty programming a gate operator or garage door opener by using the “Programming Universal Home Remote” procedures, regardless of where you live, replace Step 3 under “Programming Universal Home Remote” with the following: Continue to press and hold the Universal Home Remote button while you press and release every two seconds (cycle) the hand-held transmitter button until the frequency signal has been successfully accepted by the Universal Home Remote. The Universal Home Remote indicator light will ﬂash slowly at ﬁrst and then rapidly. Proceed with Step 4 under “Programming Universal Home Remote” to complete. 138 Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons To erase programming from the three Universal Home Remote buttons do the following: 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. Do not hold the two outside buttons for longer than 30 seconds. 2. Release both buttons. The Universal Home Remote is now in the training (learning) mode and can be programmed at any time beginning with Step 2 under “Programming Universal Home Remote” shown earlier in this section. Individual buttons cannot be erased, but they can be reprogrammed. See “Reprogramming a Single Universal Home Remote Button” following this section. Reprogramming a Single Universal Home Remote Button To program a device to Universal Home Remote using a Universal Home Remote button previously trained, follow these steps: 1. Press and hold the desired Universal Home Remote button. Do not release the button. 2. The indicator light will begin to ﬂash after 20 seconds. While still holding the Universal Home Remote button, proceed with Step 2 under “Programming Universal Home Remote” shown earlier in this section. For additional information on Universal Home Remote, see Customer Assistance Offices on page 468. Storage Areas Glove Box Open the glove box by pulling the handle to the left. Use the key to lock and unlock. Cupholder(s) Your vehicle has a cupholder on the instrument panel next to the radio. To open the cupholder, push once on the support and the cupholder will move into position for use. To close the cupholder, lift the support up towards the instrument panel. A cupholder is located on the front of the center console and two more are located at the rear of the center console. To use the rear cupholders, pull down on the lid. 139 Overhead Console Your vehicle may have this feature. The overhead console may include reading lamps, a Universal Home Remote, and a moonroof switch. See the following for more information: (cid:127) Reading Lamps on page 164. (cid:127) Universal Home Remote System (With Three Round LED) on page 128 or Universal Home Remote System (With One Triangular LED) on page 129. (cid:127) Moonroof on page 144. Center Console Storage Area Grasp the front lever on the center console while lifting the top to open it. The console may contain one or more of the following components: (cid:127) Rear Seat Audio Controls. See Rear Seat Audio (RSA) on page 257 for more information. (cid:127) Rear Climate Control. See Rear Climate Control System on page 173 for more information. (cid:127) Accessory Power Outlets. See Accessory Power Outlet(s) on page 166 for more information. Ignition Switch. See Ignition Positions on page 107. (cid:127) If your vehicle has the center armrest compartment, lift the cover by pulling up on the latch handle located underneath the front edge of the armrest. 140 Luggage Carrier {CAUTION: If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along. This can cause you to lose control. What you are carrying could be violently torn off, and this could cause you or other drivers to have a collision, and of course damage your vehicle. You may be able to carry something like this inside. But, never carry something longer or wider than the luggage carrier on top of your vehicle. Your vehicle may be equipped with a luggage carrier that allows you to load things on top of your vehicle. The luggage carrier, if equipped, has side rails attached to the roof, and places to use for tying things down. These let you load some other things on top of your vehicle, as long as they are not wider or longer than the luggage carrier. Crossrails can be purchased from your dealer. Notice: Loading cargo on the luggage carrier that weighs more than 200 lbs (91 kg) or hangs over the rear or sides of the vehicle may damage your vehicle. Load cargo so that it rests on the slats as far forward as possible and against the side rails, making sure to fasten it securely. Do not exceed the maximum vehicle capacity when loading your vehicle. For more information on vehicle capacity and loading, see Loading Your Vehicle on page 296. To prevent damage or loss of cargo as you are driving, check now and then to make sure the luggage carrier is locked and cargo is still securely fastened. When the luggage carrier is not in use, place the crossrails at the following positions for reduced wind noise. Place one crossrail at the rear most point of the vehicle and the other crossrail above the opening of the rear door. 141 Cargo Cover The cargo cover can be used to cover items in the cargo area of your vehicle. To install the cargo cover, do the following: 1. Align the endcap with the pocket in the trim panel located behind the rear seat. 2. Squeeze the opposite endcap, align it with the pocket located on the opposite side of the trim panel and release. 3. Grasp the handle and unroll the cover. Latch the posts into the sockets on the inside of the vehicle to secure it. Rear Floor Storage Lid {CAUTION: If any removable convenience item is not secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure any such item properly. Your vehicle has a rear cargo area with a removable storage lid. To remove the rear ﬂoor storage lid, do the following: 1. Press the latch release and lift up the latch handle. 2. Raise the lid slightly to unhook it. 3. Pull the lid toward you to release it from the forward mounting slots. To reinstall the rear ﬂoor storage lid, reverse the previous steps. Make sure the lid is secure by applying slight pressure to the latch until you hear it click. 142 Cargo Tie Downs There may be cargo tie downs in the rear of your vehicle that allow you to strap cargo in and keep it from moving. To remove the cargo cover, do the following: 1. Release the cover from the latch posts and carefully roll it back up. 2. Squeeze one endcap and remove it from the pocket in the trim panel. 3. Remove the cargo cover from the other endcap so that you can remove the shade from the vehicle. {CAUTION: An improperly stored cargo cover could be thrown about the vehicle during a collision or sudden maneuver. You or others could be injured. If you remove the cover, always store it in the proper storage location. When you put it back, always be sure that it is securely reattached. 143 Moonroof The vehicle may be equipped with a power sliding moonroof. The ignition must be turned to RUN, ACC, or Retained Accessory Power (RAP) must be active to operate it. See Retained Accessory Power (RAP) on page 108. With the moonroof closed, press the front of the button to open the moonroof to the vent position. The moonroof has a sunshade which can be pulled forward to block sun rays. If the sunshade is in the closed position, it will open when the moonroof is opened. The moonroof switch is located in the overhead console. Press and release the back of the button to open the moonroof. Press and hold the front of the button to close the moonroof. 144 Section 3 Instrument Panel Instrument Panel Overview ........................ 148 Hazard Warning Flashers .......................... 150 Other Warning Devices ............................. 150 Horn .......................................................... 150 Tilt Wheel .................................................. 151 Turn Signal/Multifunction Lever .................. 151 Turn and Lane-Change Signals ................. 152 Headlamp High/Low-Beam Changer .......... 153 Flash-to-Pass ............................................ 153 Windshield Wipers ..................................... 154 Windshield Washer .................................... 155 Rear Window Wiper/Washer ...................... 155 Headlamp Washer ..................................... 156 Cruise Control ........................................... 156 Headlamps ................................................ 160 Headlamps on Reminder ........................... 160 Daytime Running Lamps (DRL) ................. 161 Automatic Headlamp System ..................... 161 Fog Lamps ................................................ 162 Instrument Panel Brightness ...................... 163 Dome Lamps ............................................. 163 Dome Lamp Override ................................ 163 Entry Lighting ............................................ 164 Exit Lighting .............................................. 164 Reading Lamps ......................................... 164 Electric Power Management ...................... 164 Battery Run-Down Protection ..................... 165 Accessory Power Outlet(s) ........................ 166 Climate Controls ......................................... 167 Dual Automatic Climate Control System ....... 167 Outlet Adjustment ...................................... 172 Rear Climate Control System .................... 173 Climate Controls Personalization ................ 173 Warning Lights, Gages, and Indicators ..... 174 Instrument Panel Cluster ........................... 175 Speedometer and Odometer ...................... 176 Trip Odometer ........................................... 176 Tachometer ............................................... 176 Safety Belt Reminder Light ........................ 177 Passenger Safety Belt Reminder Light ....... 177 Airbag Readiness Light ............................. 178 Passenger Airbag Status Indicator ............. 179 Charging System Light .............................. 182 Voltmeter Gage ......................................... 182 Brake System Warning Light ..................... 183 Anti-Lock Brake System Warning Light ...... 184 StabiliTrak® Service Light ........................... 185 StabiliTrak® Indicator Light ......................... 185 Engine Coolant Temperature Gage ............ 186 145 Section 3 Instrument Panel Tire Pressure Light .................................... 186 Malfunction Indicator Lamp ........................ 187 Oil Pressure Gage ..................................... 190 Security Light ............................................ 191 Cruise Control Light .................................. 191 Reduced Engine Power Light .................... 191 Highbeam On Light ................................... 192 Service All-Wheel Drive Light .................... 192 Check Gages Warning Light ...................... 192 Gate Ajar Light .......................................... 193 Fuel Gage ................................................. 193 Low Fuel Warning Light ............................ 194 Check Gas Cap Light ................................ 194 Driver Information Center (DIC) .................. 194 DIC Operation and Displays ...................... 195 DIC Warnings and Messages .................... 199 DIC Vehicle Customization ........................ 205 Audio System(s) ......................................... 212 Setting the Time ........................................ 213 Radio with CD ........................................... 214 Radio with Six-Disc CD ............................. 222 Using an MP3 ........................................... 233 XM Radio Messages ................................. 239 Navigation/Radio System ........................... 243 Rear Seat Entertainment System ............... 243 Rear Seat Audio (RSA) ............................. 257 Theft-Deterrent Feature ............................. 258 Audio Steering Wheel Controls .................. 259 Radio Reception ........................................ 260 Care of Your CDs and DVDs .................... 261 Care of the CD and DVD Player ............... 261 Fixed Mast Antenna .................................. 261 XM™ Satellite Radio Antenna System ....... 261 146 ✍ NOTES 147 Instrument Panel Overview 148 The main components of your instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 172. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 151. J. Hood Release. See Hood Release on page 329. K. Dome Lamp Override Button. See Dome Lamp Override on page 163. C. Audio Steering Wheel Controls. See Audio Steering Wheel Controls on page 259. D. Horn. See Horn on page 150. E. Instrument Panel Cluster. See Instrument Panel Cluster on page 175. F. Windshield Wiper/Washer Lever. See Windshield Wipers on page 154. G. Hazard Warning Flashers Button and Driver Information Center Buttons. See Hazard Warning Flashers on page 150 or Driver Information Center (DIC) on page 194. H. Rear Window Washer/Wiper. See Windshield Washer on page 155. I. Instrument Panel Brightness Control. See Instrument Panel Brightness on page 163. L. Audio System. See Audio System(s) on page 212. M. Climate Controls. See Dual Automatic Climate Control System on page 167. N. Gear Shift Lever. See Automatic Transmission Operation on page 112. O. Ignition Switch. See Ignition Positions on page 107. P. Parking Brake. See Parking Brake on page 116. Q. Accessory Power Outlet. See Accessory Power Outlet(s) on page 166. R. Cupholder. See Cupholder(s) on page 139. S. Glove Box. See Glove Box on page 139. 149 Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located in the center of the instrument panel. Your hazard warning ﬂashers work no matter what position your key is in, and even if the key is not in the ignition switch. Press the button to make the front and rear turn signal lamps ﬂash on and off. Press the button again to turn the ﬂashers off. When the hazard warning ﬂashers are on, your turn signals will not work. Other Warning Devices If you carry reﬂective triangles, you can set them up at the side of the road about 300 feet (100 m) behind your vehicle. Horn To sound the horn, press the horn symbols on the steering wheel pad. 150 Tilt Wheel The steering wheel should be adjusted before you drive. Turn Signal/Multifunction Lever The tilt lever is located to the left of the steering column, under the turn signal lever. It can be raised to the highest level to give your legs more room when you enter and exit the vehicle. To tilt the wheel, hold the steering wheel and pull the lever toward you. Move the steering wheel to a comfortable level, then release the lever to lock the wheel in place. The lever on the left side of the steering column includes the following: (cid:127) G Turn and Lane-Change Signals. See Turn and Lane-Change Signals on page 152. (cid:127) O Headlamps. See Headlamps on page 160. (cid:127) 23 Headlamp High/Low Beam-Changer. See Headlamp High/Low-Beam Changer on page 153. (cid:127) Flash-To-Pass Feature. See Flash-to-Pass on page 153. (cid:127) - Fog Lamps. See Fog Lamps on page 162. (cid:127) I Cruise Control. See Cruise Control on page 156. 151 Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions let you signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is ﬁnished, the lever returns automatically. An arrow on the instrument panel cluster ﬂashes in the direction of the turn or lane change. To signal a lane change, raise or lower the lever until the arrow starts to ﬂash. Hold it there until you complete your lane change. The lever returns by itself when released. The bottom of the outside rearview mirrors might also have lane change indicators. As you signal a turn or a lane change, if the arrows ﬂash more quickly than normal, a signal bulb could be burned out and other drivers will not see your turn signal. If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when you signal a turn, check the fuse. See Fuses and Circuit Breakers on page 435 and check for burned-out bulbs. If you have a trailer towing option with added wiring for the trailer lamps, a turn signal ﬂasher is used. With this ﬂasher installed, the signal indicator ﬂashes even if a turn signal bulb is burned out. Check the front and rear turn signal lamps regularly to make sure they are working. Turn Signal On Chime If your turn signal is left on for more than 3/4 of a mile (1.2 km), a chime sounds at each ﬂash of the turn signal. To turn off the chime, move the turn signal lever to the off position. 152 Headlamp High/Low-Beam Changer To change the headlamps from low to high beam, push the lever toward the instrument panel. To return to low-beam headlamps, pull the multifunction lever toward you. Then release it. When the high beams are on, this indicator light on the instrument panel cluster will also be on. Flash-to-Pass This feature lets you use your high-beam headlamps to signal a driver in front of you that you want to pass. It works even if your headlamps are in the automatic position. To use it, pull the turn signal lever toward you, then release it. If the headlamps are in the automatic position or on low beam, the high-beam headlamps turn on. They will stay on as long as you hold the lever toward you. The high-beam indicator on the instrument panel cluster comes on. Release the lever to return to normal operation. 153 Windshield Wipers The lever on the right side of the steering column operates the windshield wipers. 7(Mist): Pull the lever down and release it for a single wiping cycle. The lever will return to its original position. For more cycles, hold the lever down before releasing it. 9(Off): Put the lever in this position to turn off the wipers. &(Delay): Put the lever in this position to set a delay between wipes. Turn the delay adjustment band to set the length of the delay. 154 x(Delay Adjustment): Use this band to set the length of the delay between wipes when using the delay feature. The closer you move the band toward mist, the longer the delay. The windshield wiper lever must be in delay for this feature to work. 6 (Low Speed): Put the lever in this position for slow, steady wiping cycles. 1 (High Speed): Put the lever in this position for rapid wiping cycles. If the windshield wipers are in use for about six seconds while you are driving, the exterior lamps will come on automatically if the exterior lamp control is in AUTO. Be sure to clear ice and snow from the wiper blades before using them. If they’re frozen to the windshield, gently loosen or thaw them. If the blades do become damaged, install new blades or blade inserts. For more information, see Windshield Wiper Blade Replacement on page 377. Heavy snow or ice can overload the wiper motor. A circuit breaker will stop the motor until it cools down. Clear away snow or ice to prevent an overload. Windshield Washer L(Windshield Washer): To spray washer ﬂuid on the windshield, press the windshield washer paddle. The wipers will clear the window and then either stop or return to your preset speed. {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. Rear Window Wiper/Washer {CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. This control is located to the left of the steering wheel on the instrument panel. To turn the rear wiper on, turn the control to either 1, 2, or 3. For delayed wiping, turn the control to 1 or 2. For steady wiping, turn the control to 3. To turn the wiper off, turn the control to 0. To wash the rear window, press the washer symbol located in the center of the control. The rear window washer uses the same ﬂuid bottle as the windshield washer. However, the rear window washer will run out of ﬂuid before the windshield washer. If you can wash your windshield but not your rear window, check the ﬂuid level. 155 Headlamp Washer Your vehicle may be equipped with a headlamp washer system. The headlamp washers clear debris from the headlamp lenses by soaking the lens with ﬂuid, waiting for about ﬁve seconds, then rinsing the loose debris from the lenses. The headlamp washers are located under the headlamps. The headlamp washers activate for one wash-wait-rinse cycle when the front windshield washer button is pressed for the ﬁrst time after your vehicle is turned on. The headlamps washers then activate automatically for one cycle after every four front windshield washes. The headlamps must be on to be washed. If the headlamps are off, only the front windshield will be washed. See Windshield Washer on page 155 for more information. Cruise Control 9(Off): This position turns the system off. R(On): This position activates the system. + (Resume/Accelerate): Push the lever to this symbol to make the vehicle accelerate or resume to a previously set speed. T(Set): Press this button to set the speed. With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h). 156 If you apply your brakes, the cruise control will shut off. Setting Cruise Control {CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed. So, do not use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause excessive wheel slip, and you could lose control. Do not use cruise control on slippery roads. {CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Move the cruise control switch to on. 2. Get up to the speed you want. 3. Press in the set button at the end of the lever and release it. 4. Take your foot off the accelerator pedal. Some vehicles have a cruise light on the instrument panel cluster that will come on when the cruise control is engaged. 157 Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, disengages the cruise control. But you do not need to reset it. Once you’re going about 25 mph (40 km/h) or more, you can move the cruise control switch brieﬂy from on to resume/accelerate. You will go right back up to your chosen speed and stay there. If you hold the switch at resume/accelerate the vehicle will keep going faster until you release the switch or apply the brake. So unless you want to go faster, do not hold the switch at resume/accelerate. Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: (cid:127) Use the accelerator pedal to get to the higher speed. Press the set button at the end of the lever, then release the button and the accelerator pedal. You will now cruise at the higher speed. If the accelerator pedal is held longer than 60 seconds, cruise control will turn off. (cid:127) Move the cruise switch from on to resume/ accelerate. Hold it there until you get up to the speed you want, and then release the switch. To increase your speed in very small amounts, move the switch brieﬂy to resume/accelerate. Each time you do this, your vehicle will go about 1 mph (1.6 km/h) faster. Reducing Speed While Using Cruise Control (cid:127) Press in the button at the end of the lever until you reach the lower speed you want, then release it. 158 (cid:127) To slow down in very small amounts, brieﬂy press the set button. Each time you do this, you will go about 1 mph (1.6 km/h) slower. Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise control speed you set earlier. Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills. When going up steep hills, you may want to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Of course, applying the brake takes you out of cruise control. Many drivers ﬁnd this to be too much trouble and do not use cruise control on steep hills. Ending Cruise Control To turn off the cruise control, do one of the following: (cid:127) Step lightly on the brake pedal, (cid:127) move the cruise control switch to off, or (cid:127) shift the transmission to NEUTRAL (N). (cid:127) If your vehicle has the StabiliTrak® feature, cruise control will turn off if road conditions cause StabiliTrak® to activate. If the accelerator pedal is held longer than 60 seconds, cruise control will turn off. (cid:127) The cruise control will turn off automatically if the traction control system or StabiliTrak® system activate, if your vehicle is equipped with either feature. Erasing Speed Memory When you turn off the cruise control or the ignition, your cruise control set speed memory is erased. 159 Headlamps The exterior lamp control is located in the middle of the turn signal/multifunction lever. See Turn Signal/Multifunction Lever on page 151. O(Exterior Lamp Control): Turn the control with this symbol on it to operate the exterior lamps. The exterior lamp control has the following four positions: O(On/Off): Turn the control to this position to turn off the Daytime Running Lamps (DRL) and Automatic Headlamps. Turning the control to this position again turns the automatic lighting system back on. This feature is not available for vehicles ﬁrst sold in Canada. AUTO (Automatic): Turn the control to this position to put the headlamps in automatic mode. AUTO mode will turn the exterior lamps on and off depending upon how much light is available outside of the vehicle. ;(Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following: (cid:127) Sidemarker Lamps (cid:127) Taillamps (cid:127) License Plate Lamps (cid:127) 5(Headlamps): Turn the control to this position to turn on the headlamps, together with the previously listed lamps and lights. Instrument Panel Lights Headlamps on Reminder A reminder tone sounds when the headlamps or parking lamps are manually turned on, if the driver’s door is open and the ignition is in LOCK or ACC. To turn the tone off, turn the knob all the way counterclockwise. In the automatic mode, the headlamps turn off once the ignition key is in LOCK. 160 Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. The DRL will activate when the following conditions are met: (cid:127) The ignition is on. (cid:127) The exterior lamps knob is in automatic headlamp mode. (cid:127) The light sensor detects daytime light. (cid:127) The transmission is not in PARK (P). When DRL are on, either your turn signal lamps or headlamps will be on. If your vehicle is equipped with the High Intensity Discharge (HID) lighting system option, the DRL system will turn on your turn signal lamps. If your vehicle is not equipped with HID, the DRL system will turn on your headlamps at reduced brightness. The taillamps, sidemarker and other lamps won’t be on. The instrument panel won’t be lit up either. When it begins to get dark, the headlamps will automatically switch from DRL to the regular headlamps. Automatic Headlamp System When it is dark enough outside, the Automatic Headlamp System turns on the headlamps when the vehicle is started and after the transaxle has been shifted out of the PARK (P) position. The headlamps, taillamps, sidemarker, and parking lamps will come on. The instrument panel lights and radio lights will also turn on at normal brightness. Once on, the system remains on during these conditions even if the vehicle is shifted back into PARK (P). The vehicle has a light sensor on the top of the instrument panel. Make sure it is not covered or the system may come on whenever the ignition is on and the vehicle is shifted out of the PARK (P) position. The system could also turn on the lamps when driving through a parking garage, heavy overcast weather or a tunnel. This is normal. 161 There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp systems, so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system are only affected when the light sensor sees a change in lighting lasting longer than the delay. If you start your vehicle in a dark garage, the automatic headlamp system comes on after the transmission is shifted out of PARK (P). Once you leave the garage, it will take about one minute for the automatic headlamp system to change to DRL if it is light outside. During that delay, the instrument panel cluster might not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position. If the vehicle is running and the automatic headlamp system is already on, it can be turned off by turning and releasing the headlamp control at the off position. The automatic headlamp system stays off until you turn and release the headlamp control at the off position again. See Headlamps on page 160. 162 Fog Lamps The fog lamp control is located on the turn signal/multifunction lever. Use the fog lamps for better vision in foggy or misty conditions. -: The band with this symbol is used to turn the fog lamps on and off. When the fog lamps are turned on, the parking lamps also turn on. A message will also display on the DIC when the fog lamps are turned on or off. See Driver Information Center (DIC) on page 194. (cid:127) To turn the fog lamps on or off, turn the fog (cid:127) lamp band on the lever up to the dot and release it. The band will return to its original position. If you turn on the high-beam headlamps, the fog lamps will turn off. They will turn back on again when you switch back to low-beam headlamps. When the Fog Lamps are turned on or off, a message will appear on the Driver Information Center. See DIC Warnings and Messages on page 199. Some localities have laws that require the headlamps to be on along with the fog lamps. Instrument Panel Brightness Dome Lamp Override Turn the knob to adjust the instrument panel lights. Turn the knob clockwise or counterclockwise to brighten or dim the interior lamps. Dome Lamps The dome lamps will automatically come on when you open a door, unless the dome lamp override button is pressed in. You can also turn on the dome lamps by turning the instrument panel brightness control all the way clockwise to the detent position. In this position, the dome lamps will remain on until they are turned off. The dome override button is located to the left of the steering column on the instrument panel. To turn the dome lamps off, press the button. The dome lamps will remain off when a door is open. This will override the illuminated entry feature unless you use your remote keyless entry transmitter to unlock the vehicle. To return the lamps to automatic operation, press the button again. The dome lamps will come on when you open any door. 163 Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly put the charge back in. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. Entry Lighting The vehicle has entry lighting. When any door is opened, the dome lamps come on as long as the dome override lamp override button is not pressed in. When all the doors are closed, the lamps stay on for a short period of time and then turn off automatically. If you use the Remote Keyless Entry (RKE) transmitter to unlock the vehicle, the interior lamps come on for a short time whether or not the dome lamp override is on. Exit Lighting With exit lighting, the interior lamps will come on when you remove the key from the ignition. If the dome override is off, these lights will stay on for a short period of time and then will go out. Reading Lamps Press the indented part of the lenses on the reading lamps located in the overhead console to turn them on or off. 164 A high electrical load occurs when several of the following loads are on: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as Battery Saver Active or Service Battery Charging System. If this message is displayed, it is recommended that the driver reduce the electrical loads as much as possible. See DIC Warnings and Messages on page 199. Battery Run-Down Protection This feature shuts off the dome, courtesy, and vanity lamps if they are left on for more than 20 minutes when the ignition is off. This will keep the battery from running down. If the battery run-down protection shuts off the interior lamps, it may be necessary to do one of the following to return to normal operation: (cid:127) Shut off all lamps and close all doors. (cid:127) Turn the ignition key to RUN. This feature will also turn off the parking lamps and headlamps under most circumstances, if they are left on. If you would like to turn them back on, turn the exterior lamps knob. 165 Accessory Power Outlet(s) With the accessory power outlets, you can plug in auxiliary electrical equipment such as a cellular telephone or CB radio. Your vehicle has three accessory power outlets. There are two outlets located below the climate controls and one outlet is on the rear of the center ﬂoor console. Remove the cover from the outlet to use the outlet. Be sure to put the cover back on when not using the accessory power outlet. Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adaptor fuses. If you experience a problem, see your dealer for additional information on the accessory power outlets. Notice: Adding any electrical equipment to your vehicle may damage it or keep other components from working as they should. The repairs would not be covered by your warranty. Do not use equipment exceeding maximum amperage rating of 20 amperes. Check with your dealer before adding electrical equipment. When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. 166 Climate Controls Dual Automatic Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. When your vehicle is ﬁrst started and the climate control system is on, or if the climate control system has been turned on, the display will show the driver’s temperature setting for ﬁve seconds. Then it will show the outside temperature. 9(Off): Press this button to turn off the entire climate control system. Outside air will still enter the vehicle, and will be directed to the ﬂoor. Press the AUTO button, the mode button, the fan arrows, or either temperature knob to turn the system on. C(Mode): Press this button to manually select the air delivery mode to the ﬂoor, instrument panel, or windshield outlets. The system will stay in the selected mode until the mode button is pressed again or the AUTO button is pressed. Driver’s Side Temperature Knob: Turn this knob clockwise or counterclockwise to raise or lower the temperature on the driver’s side of the vehicle. The display will show the temperature setting decreasing or increasing and an arrow pointing toward the driver. This knob can also adjust the passenger’s side temperature setting if the two are linked. 167 Passenger’s Side Temperature Knob: Turn this knob clockwise or counterclockwise to manually raise or lower the temperature on the passenger’s side of the vehicle. The display will show the temperature setting decreasing or increasing and an arrow pointing toward the passenger. The passenger’s temperature setting can be set to match and link to the driver’s temperature setting by pressing and holding the AUTO button for three seconds. When adjusting the driver’s side temperature setting, the passenger’s side temperature setting will follow and both arrows will appear on the display. The passenger’s side temperature setting also resets and relinks to the driver’s side temperature setting if the vehicle has been off for more than three hours. Outside Air Temperature Display A new outside temperature reading will be displayed if the vehicle has been off for more than three hours. If the vehicle has been off for less than three hours, the old temperature reading may be displayed because underhood heat is affecting the true outside temperature. Underhood heat can also affect the outside temperature while the engine is running. It may also take several minutes of driving before the display updates to the actual outside temperature. Automatic Operation AUTO (Automatic): When automatic operation is active, the system will control the inside temperature, the air delivery mode, and the fan speed. 168 Use the steps below to place the entire system in automatic mode: 1. Press the AUTO button. When AUTO is selected, the air conditioning operation and air outlet mode will be automatically controlled. The air conditioning compressor will run continuously when the outside temperature is over approximately 40°F (4°C). The air inlet will normally be set to outside air. If it’s hot outside, the air inlet will automatically switch to recirculate inside air to help quickly cool down your vehicle. 2. Set the driver’s and passenger’s temperature. To ﬁnd your comfort setting, start with a 72°F (22°C) temperature setting and allow about 20 minutes for the system to adjust. Turn the driver’s or passenger’s side temperature knob to adjust the temperature setting as necessary. If you choose the temperature setting of 60°F (15°C), the system will remain at the maximum cooling setting. If you choose the temperature setting of 90°F (32°C), the system will remain at the maximum heat setting. Choosing either maximum setting may not cause the vehicle to heat or cool any faster. Manual Operation To change the current setting, select one of the following: w9x(Fan): This button allows you to manually adjust the fan speed. Press the up arrow to increase fan speed and the down arrow to decrease fan speed. The display will change to show you the selected fan speed and the driver’s side temperature setting for ﬁve seconds. C(Mode): Press this button to manually change the direction of the airﬂow in your vehicle. Keep pressing the button until the desired mode appears on the display. The display will change to show you the selected air delivery mode and the driver’s temperature setting for ﬁve seconds. H(Vent): This mode directs air to the instrument panel outlets. )(Bi-Level): This mode directs approximately half of the air to the instrument panel outlets, then directs the remaining air to the ﬂoor outlets. A little air is directed toward the windshield and the side window outlets. Cooler air is directed to the upper outlets and warmer air to the ﬂoor outlets. 169 6(Floor): This mode directs most of the air to the ﬂoor outlets. Some air also comes out of the defroster and side window outlets. The recirculation button cannot be selected in ﬂoor mode. @(Recirculation): Press this button to turn recirculation mode on or off. When this button is pressed, an indicator light in the button will also come on to let you know that it is activated. Recirculation mode is used to recirculate the air inside of your vehicle. Use this mode to help prevent outside odors and/or dust from entering your vehicle or to help cool the air inside of your vehicle more quickly. Recirculation mode can be used with vent and bi-level modes, but it cannot be used with ﬂoor, defog or defrost modes. Defog and defrost modes are described later in this section. If recirculation mode is selected with ﬂoor, defog, or defrost modes, the indicator will ﬂash three times and then turn off indicating the selection is not available. You may also notice that the air conditioning compressor will run while in recirculation mode. This is normal and will help to prevent fogging. If the weather is cold and damp, the system may cause the windows to fog while using recirculation mode. If the windows do start to fog, select defog or defrost mode and increase fan speed. Recirculation mode, if selected, will be cleared when the engine is turned off. #A/C (Air Conditioning): Press this button to manually turn the air conditioning system on or off. When the system is on, the system will automatically begin to cool and dehumidify the air inside of your vehicle. The air conditioning symbol will appear on the display when the air conditioning is on and will turn off when the air conditioning is off. 170 If you turn the air conditioning off while in front defrost or defog mode, the air conditioning symbol will turn off, however, the A/C compressor will remain on to help de-humidify the air inside the vehicle. If one of the other modes is selected the compressor will then turn the A/C off until it is selected again or the AUTO button is pressed. To avoid fogging the inside glass on rainy and humid days at a temperature above freezing, press the air conditioning button to run the A/C compressor. Also it is best to avoid the use of the recirculation mode except when maximum air conditioning performance is needed or for short times to avoid exterior odors. You may notice a slight change in engine performance when the air-conditioning compressor shuts off and turns on again. This is normal. Defogging and Defrosting Fog on the inside of the windows is a result of moisture condensing on the cool window glass. This can be reduced if the climate control system is used properly. You can use either defog or front defrost to clear fog or frost from your windshield. -(Defog): Use this setting to clear the windows of fog or moisture. This setting will deliver air to the ﬂoor and windshield outlets. 0(Front Defrost): Press the front defrost button to clear the windshield and side windows of frost or fog quickly. The system will automatically control the fan speed if you select defrost from AUTO mode. If the outside temperature is 40°F (4°C) or warmer, your air conditioning compressor will automatically run to help dehumidify the air and dry the windshield. Do not drive the vehicle until all the windows are clear. 171 Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. <(Rear): Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is activated. The rear window defogger will turn off approximately 10 minutes after the button is pressed. If you need additional warming time, press the button again. The heated mirrors will also come on when you press this button. See Outside Heated Mirrors on page 124. Notice: Do not use a razor blade or sharp object to clear the inside rear window. Do not adhere anything to the defogger grid lines in the rear glass. These actions may damage the rear defogger. Repairs would not be covered by your warranty. 172 Outlet Adjustment Use the air outlets located in the center and on the sides of your instrument panel to direct the airﬂow. Operation Tips (cid:127) Keep the hood and front air inlets free of ice, snow, or any other obstruction, such as leaves. The heater and defroster will work far better, reducing the chance of fogging the inside of your windows. (cid:127) When you enter a vehicle in cold weather, select maximum blower speed for a few moments before driving. This helps clear the intake ducts of snow and moisture, and reduces the chance of fogging the inside of your window. (cid:127) Keep the air path under the front seats clear of objects. This helps air to circulate throughout your vehicle. (cid:127) Adding outside equipment to the front of your vehicle, such as hood-air deﬂectors, may affect the performance of the heating and air conditioning system. Check with your dealer before adding equipment to the outside of your vehicle. Rear Climate Control System The lower buttons on the rear seat audio are used to adjust the rear seat climate controls. The temperature of the air coming through the rear outlets is determined by the front passenger’s temperature setting. z9y(Fan) Press this button to adjust the fan speed. z\y(Mode) Press this button to change the direction of airﬂow in the rear seat area to either vent, bi-level or ﬂoor mode. P(On/Off) Press this button to turn the rear climate controls on or off. The rear control will only turn on if the front is on and not in defrost mode. Climate Controls Personalization Your vehicle is equipped with a Driver Information Center (DIC). You can store and recall the climate control settings for temperature, air delivery mode and fan speed for two different drivers. The personal choice settings recalled are determined by the transmitter used to enter the vehicle. After the button with the unlock symbol on a remote keyless entry transmitter is pressed, the climate control will adjust to the last settings of the identiﬁed driver. The settings can also be changed by pressing one of the memory buttons (1 or 2) located on the driver’s door. When adjustments are made, the new settings are automatically saved for the driver. 173 Warning Lights, Gages, and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to your warning lights and gages could also save you or others from injury. Warning lights come on when there may be or is a problem with one of your vehicle’s functions. As you will see in the details on the next few pages, some warning lights come on brieﬂy when you start the engine just to let you know they are working. If you are familiar with this section, you should not be alarmed when this happens. Gages can indicate when there may be or is a problem with one of your vehicle’s functions. Often gages and warning lights work together to let you know when there is a problem with your vehicle. When one of the warning lights comes on and stays on when you are driving, or when one of the gages shows there may be a problem, check the section that tells you what to do about it. Please follow this manual’s advice. Waiting to do repairs can be costly—and even dangerous. So please get to know your warning lights and gages. They are a big help. Your vehicle has a Driver Information Center (DIC) that works along with the warning lights and gages. See Driver Information Center (DIC) on page 194. 174 Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You will know how fast you are going, about how much fuel you have used, and many other things you will need to know to drive safely and economically. United States version shown, Canada similar 175 Speedometer and Odometer The speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). The odometer mileage can be checked without the vehicle running. Press the trip stem located on the instrument panel cluster. If your vehicle needs a new odometer installed, the new one will be set to the correct mileage total of the old odometer. Trip Odometer The trip odometer can tell you how far your vehicle has been driven since you last set the trip odometer to zero. The odometer works together with the Driver Information Center (DIC). You can set a Trip A and Trip B odometer. See “Trip Information” under DIC Operation and Displays on page 195. The odometer mileage can be checked without the vehicle running. Press the trip stem on the instrument panel cluster. Tachometer The tachometer displays the engine speed in revolutions per minute (rpm). 176 Safety Belt Reminder Light When the key is turned to RUN or START, a chime will sound for several seconds to remind you buckle your safety belt. The driver safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. You should buckle your seat belt. This chime and light will be repeated if the driver remains unbuckled and the vehicle is in motion. If the driver’s belt is buckled, neither the chime nor the light will come on. Passenger Safety Belt Reminder Light Several seconds after the key is turned to RUN or START, a chime will sound for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 74 for more information. The passenger safety belt light will also come on and stay on for several seconds, then it will ﬂash for several more. This chime and light will be repeated if the passenger remains unbuckled and the vehicle is in motion. If the passenger’s safety belt is buckled, neither the chime nor the light will come on. 177 Airbag Readiness Light There is an airbag readiness light on the instrument panel, which shows the airbag symbol. The system checks the airbag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the airbag sensors, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 64. This light will come on when you start your vehicle, and it will ﬂash for a few seconds. Then the light should go out. This means the system is ready. {CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the airbag readiness light stays on after you start your vehicle. If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. The airbag readiness light should ﬂash for a few seconds when you turn the ignition key to RUN. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. 178 Passenger Airbag Status Indicator Your vehicle has the passenger sensing system. Your rearview mirror has a passenger airbag status indicator. When the ignition key is turned to RUN or START, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either ON or OFF, or either the on or off symbol to let you know the status of the right front passenger’s frontal airbag. United States Canada 179 If the word ON or the on symbol is lit on the passenger airbag status indicator, it means that the right front passenger’s frontal airbag is enabled (may inﬂate). {CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag. A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. Do not use a rear-facing child restraint in the right front passenger’s seat if the airbag is turned on. If your vehicle has a rear seat that will accommodate a rear-facing child restraint, a label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. {CAUTION: Even though the passenger sensing system is designed to turn off the passenger’s frontal airbag if the system detects a rear-facing child restraint, no system is failsafe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. We recommend that rear-facing child restraints be secured in the rear seat, even if the airbag is off. 180 If your vehicle does not have a rear seat that will accommodate a rear-facing child restraint, never put a child in a rear-facing child restraint in the right front passenger seat unless the passenger airbag status indicator shows off and the airbag is off. Here is why: {CAUTION: Even though the passenger sensing system is designed to turn off the passenger’s frontal airbag if the system detects a rear-facing child restraint, no system is fail-safe, and no one can guarantee that an airbag will not deploy under some unusual circumstance, even though it is turned off. We recommend that rear-facing child restraints be transported in vehicles with a rear seat that will accommodate a rear-facing child restraint, whenever possible. If the word OFF or the off symbol is lit on the airbag status indicator, it means that the passenger sensing system has turned off the right front passenger’s frontal airbag. See Passenger Sensing System on page 74 for more on this, including important safety information. If, after several seconds, all status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service. {CAUTION: If the off indicator and the airbag readiness light ever come on together, it means that something may be wrong with the airbag system. If this ever happens, have the vehicle serviced promptly, because an adult-size person sitting in the right front passenger seat may not have the protection of the frontal airbag. See Airbag Readiness Light on page 178. 181 Charging System Light Voltmeter Gage The charging system light will come on brieﬂy when you turn on the ignition, but the engine is not running, as a check to show you it is working. It should go out once the engine is running. If it stays on, or comes on while you are driving, you may have a problem with the charging system. It could indicate that you have problems with a generator drive belt, or another electrical problem. Have it checked right away. Driving while this light is on could drain your battery. If you must drive a short distance with the light on, be certain to turn off all your accessories, such as the radio and air conditioner. 182 United States Canada When your engine is not running, but the ignition is in RUN, this gage shows your battery’s state of charge in DC volts. When the engine is running, the gage shows the condition of the charging system. The gage may transition from a higher to lower or a lower to higher reading. This is normal. Readings between the low and high warning zones indicate the normal operating range. The voltmeter gage may also read lower when in fuel economy mode. This is normal. Readings in the low warning zone may occur when a large number of electrical accessories are operating in the vehicle and the engine is left idling for an extended period. This condition is normal since the charging system is not able to provide full power at engine idle. As engine speeds are increased, this condition should correct itself as higher engine speeds allow the charging system to create maximum power. You can only drive for a short time with the reading in either warning zone. If you must drive, turn off all unnecessary accessories. Readings in either warning zone indicate a possible problem in the electrical system. Have the vehicle serviced as soon as possible. Brake System Warning Light When the ignition is on, the brake system warning light will come on when you set your parking brake. The light will stay on if your parking brake does not release fully. If it stays on after your parking brake is fully released, it means your vehicle has a brake problem. A chime may also sound when the light comes on. Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there could be a brake problem. Have your brake system inspected right away. United States Canada 183 This light should come on brieﬂy when you turn the ignition key to RUN. If it does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. If the light comes on while you are driving, pull off the road and stop carefully. You may notice that the pedal is harder to push or the pedal may go closer to the ﬂoor. It may take longer to stop. If the light is still on, have the vehicle towed for service. See Towing Your Vehicle on page 302. {CAUTION: Your brake system may not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to an accident. If the light is still on after you have pulled off the road and stopped carefully, have the vehicle towed for service. Anti-Lock Brake System Warning Light With the Anti-Lock Brake System (ABS), this light will come on when you start your engine and may stay on for several seconds, that is normal. A chime may also sound when the light comes on. If the light stays on, or comes on when you are driving, your vehicle needs service. If the regular brake system warning light is not on, you still have brakes, but you do not have anti-lock brakes. If the regular brake system warning light is also on, you do not have anti-lock brakes and there is a problem with your regular brakes. See Brake System Warning Light on page 183 earlier in this section. The ABS warning light should come on brieﬂy when you turn the ignition key to RUN. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. 184 StabiliTrak® Service Light StabiliTrak® Indicator Light This light will come on brieﬂy when the engine is started. This warning light should come on brieﬂy when the engine is started. This light will come on if a problem is detected in the StabiliTrak® system. For more information see StabiliTrak® System on page 271. During most driving conditions, this light will not come on. If the StabiliTrak® System is actively controlling the stability and/or traction of the vehicle, this light will blink. This is normal. This light will come on if any portion of the system has been manually turned off or a problem is detected in the system. If your vehicle is equipped with a Driver Information Center, a message will appear also, see DIC Warnings and Messages on page 199 and StabiliTrak® System on page 271 for more information. 185 Engine Coolant Temperature Gage Tire Pressure Light This light will come on brieﬂy when you turn the ignition to RUN. United States Canada This gage shows the engine coolant temperature. If the gage pointer moves into the red area, the engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as soon as possible. See Engine Overheating on page 347. 186 This light will also come on when one or more of your tires are signiﬁcantly underinﬂated. A CHECK TIRE PRESSURE DIC message will accompany the light, see DIC Warnings and Messages on page 199. Stop and check your tires as soon as it is safe to do so. If underinﬂated, inﬂate to the proper pressure. See Tires on page 380 for more information. This light will ﬂash for approximately 70 seconds and then turn on solid if a problem is detected with the Tire Pressure Monitor system. See Tire Pressure Monitor System on page 391 for more information. Malfunction Indicator Lamp Check Engine Light Your vehicle has a computer which monitors operation of the fuel, ignition, and emission control systems. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The check engine light comes on to indicate that there is a problem and service is required. Malfunctions often will be indicated by the system before any problem is apparent. This may prevent more serious damage to your vehicle. This system is also designed to assist your service technician in correctly diagnosing any malfunction. If you keep driving your vehicle with Notice: this light on, after awhile, your emission controls may not work as well, your fuel economy may not be as good, and your engine may not run as smoothly. This could lead to costly repairs that may not be covered by your warranty. Notice: Modiﬁcations made to the engine, transmission, exhaust, intake, or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission controls and may cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by your warranty. This may also result in a failure to pass a required Emission Inspection/Maintenance test. See Accessories and Modiﬁcations on page 322. 187 This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: (cid:127) Light Flashing — A misﬁre condition has been detected. A misﬁre increases vehicle emissions and may damage the emission control system on your vehicle. Diagnosis and service may be required. (cid:127) Light On Steady — An emission control system malfunction has been detected on your vehicle. Diagnosis and service may be required. If the Light is Flashing The following may prevent more serious damage to your vehicle: (cid:127) Reducing vehicle speed (cid:127) Avoiding hard accelerations (cid:127) Avoiding steep uphill grades (cid:127) If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible If the light stops ﬂashing and remains on steady, see “If the Light Is On Steady” following. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park your vehicle. Turn the key off, wait at least 10 seconds and restart the engine. If the light remains on steady, see “If the Light Is On Steady” following. If the light is still ﬂashing, follow the previous steps, and see your dealer for service as soon as possible. If the Light Is On Steady You may be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling the Tank on page 326. The diagnostic system can determine if the fuel cap has been left off or improperly installed. A loose or missing fuel cap will allow fuel to evaporate into the atmosphere. A few driving trips with the cap properly installed should turn the light off. 188 Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 324. Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration. (These conditions may go away once the engine is warmed up.) This will be detected by the system and cause the light to turn on. If you experience one or more of these conditions, change the fuel brand you use. It will require at least one full tank of the proper fuel to turn the light off. If none of the above steps have made the light turn off, your dealer can check the vehicle. Your dealer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that may have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the check engine light is on or not working properly. Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced your battery or if your battery has run down. The diagnostic system is designed to evaluate critical emission control systems during normal driving. This may take several days of routine driving. If you have done this and your vehicle still does not pass the inspection for lack of OBD system readiness, your dealer can prepare the vehicle for inspection. 189 A reading in the low pressure zone may be caused by a dangerously low oil level or other problems causing low oil pressure. {CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced. Notice: Lack of proper engine oil maintenance may damage the engine. The repairs would not be covered by your warranty. Always follow the maintenance schedule in this manual for changing engine oil. Oil Pressure Gage United States Canada The oil pressure gage shows the engine oil pressure in psi (pounds per square inch) when the engine is running. Canadian vehicles indicate pressure in kPa (kilopascals). Oil pressure may vary with engine speed, outside temperature and oil viscosity, but readings above the low pressure zone indicate the normal operating range. 190 Security Light Reduced Engine Power Light This light will come on brieﬂy when you turn the key toward START. This light comes on when a noticeable reduction in the vehicle’s performance occurs. See PASS-Key® III Operation on page 104 for additional information regarding the security light. Cruise Control Light This light will come on when the cruise control is set. The vehicle can be driven at a reduced speed when the reduced engine power light is on, but acceleration and speed may be reduced. The performance may be reduced until the next time you drive your vehicle. If this light stays on, see your dealer as soon as possible for diagnosis and repair. This light may also come on if there is a problem with the Electronic Throttle Control (ETC) system. If this happens, take the vehicle in for service as soon as possible. See Cruise Control on page 156 for more information. 191 Highbeam On Light This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 153. Service All-Wheel Drive Light This light should come on brieﬂy when you turn on the ignition, as a check to show you it is working. The service all-wheel drive light comes on to indicate that there may be a problem with the drive system and service is required. Malfunctions can be indicated by the system before any problem is apparent, which may prevent serious damage to the vehicle. This system is also designed to assist your dealer in correctly diagnosing a malfunction. Check Gages Warning Light The check gages light will come on brieﬂy when you are starting the engine. If the light comes on and stays on while you are driving, check your coolant temperature and engine oil pressure gages to see if they are in the warning zones. 192 Gate Ajar Light If this light comes on, the liftgate or liftglass is not completely shut. Close the liftgate or liftglass. Never drive with the liftgate or liftglass even partially open. Fuel Gage When the ignition is on, the fuel gage tells you about how much fuel you have remaining. Here are four things that some owners ask about. None of these show a problem with your fuel gage: (cid:127) At the gas station, the gas pump shuts off (cid:127) before the gage reads full. It takes a little more or less fuel to ﬁll up than the gage indicated. For example, the gage may have indicated the tank was half full, but it actually took a little more or less than half the tank’s capacity to ﬁll the tank. (cid:127) The gage moves a little when you turn a corner or speed up. (cid:127) The gage doesn’t go back to empty when you turn off the ignition. United States Canada 193 Low Fuel Warning Light The light next to the fuel gage will come on brieﬂy when you are starting the engine. This light comes on when the fuel tank is low on fuel. To turn it off, add fuel to the fuel tank. See Fuel on page 324. Check Gas Cap Light Driver Information Center (DIC) The Driver Information Center (DIC) display is located on the instrument panel cluster, below the speedometer. The DIC buttons are located on the center of the instrument panel, above the radio. The DIC can display information such as the trip odometer, fuel economy, customization features, and warning/status messages. If your vehicle has this light, it will come on if your gas cap is not securely fastened. See Malfunction Indicator Lamp on page 187 for more information. r (Fuel Information): Press this button to display the fuel range, fuel used, average fuel economy, and engine oil life. See DIC Operation and Displays on page 195 for more information. 194 3 (Trip Information): Press this button to display the odometer, trip odometers, and timer. See DIC Operation and Displays on page 195 for more information. | (Hazard): Press this button to turn the hazard warning ﬂashers on and off. See Hazard Warning Flashers on page 150 for more information. q (Customization): Press this button to access the vehicle settings menu and customize the personal settings on your vehicle. See DIC Vehicle Customization on page 205 for more information. r (Select): Press this button to reset certain DIC functions and set your customization settings. Pressing any of the DIC buttons will acknowledge DIC messages and clear them from the DIC display. DIC Operation and Displays The DIC comes on when the ignition is on. After a short delay the DIC will display the information that was last displayed before the engine was turned off. If a problem is detected, a warning message will appear on the display. Pressing the trip stem on the instrument panel cluster or any of the DIC buttons will acknowledge any warning or service messages. You should take any message that appears on the display seriously and remember that clearing the message will only make the message disappear, not correct the problem. The DIC has different modes which can be accessed by pressing the four DIC buttons located on the center of the instrument panel, above the radio. These buttons are fuel information, trip information, customization, and select. The button functions are detailed in the following pages. 195 Fuel Information Button r (Fuel Information): Press this button to scroll through the fuel range, fuel used, average fuel economy, and the engine oil life system. Fuel Range: Press the fuel information button until RANGE appears on the display. This mode shows the remaining distance you can drive without refueling. It is based on fuel economy and the fuel remaining in the fuel tank. The display will show LOW if the fuel level is low. The fuel economy data used to determine fuel range is an average of recent driving conditions. As your driving conditions change, this data is gradually updated. Fuel range cannot be reset. Fuel Used: Press the fuel information button until FUEL USED appears on the display. This mode shows the number of gallons or liters of fuel used since the last reset of this menu item. To reset the fuel used information, press and hold the select button for one second while FUEL USED is displayed. Average Fuel Economy: Press the fuel information button until AVG. ECON appears on the display. This mode shows how many miles per gallon (MPG), kilometers per liter (km/L), or liters per 100 kilometers (L/100 km) your vehicle is getting based on current and past driving conditions. Press and hold the select button for one second while AVG. ECON is displayed to reset the average fuel economy. Average fuel economy will then be calculated starting from that point. If the average fuel economy is not reset, it will be continually updated each time you drive. Engine Oil Life System: Press the fuel information button until ENGINE OIL LIFE appears on the display. The engine oil life system shows an estimate of the oil’s remaining useful life. It will show 100% when the system is reset after an oil change. It will alert you to change your oil on a schedule consistent with your driving conditions. Always reset the engine oil life system after an oil change. To reset the engine oil life system, see Engine Oil Life System on page 337. 196 In addition to the engine oil life system monitoring the oil life, additional maintenance is recommended in the Maintenance Schedule in this manual. See Engine Oil on page 334 and Scheduled Maintenance on page 450. Trip Information Button 3 (Trip Information): Press this button to scroll through the odometer, trip odometers, tire pressures, and timer. Odometer: Press the trip information button until ODOMETER appears on the display. This mode shows the total distance the vehicle has been driven in either miles or kilometers. Pressing the trip stem located on the instrument panel cluster with the vehicle off will also display the odometer. Trip A: Press the trip information button until TRIP A appears on the display. This mode shows the current distance traveled since the last reset for TRIP A in either miles or kilometers. Trip B: Press the trip information button until TRIP B appears on the display. This mode shows the current distance traveled since the last reset for TRIP B in either miles or kilometers. To reset TRIP A or TRIP B information, press and hold the select button for one second while in one of the trip modes. This will reset the information for TRIP A or TRIP B. You can also reset the TRIP A or TRIP B while they are displayed by pressing the trip stem. If you press and hold the trip stem or the select button for more than four seconds, the display will show the distance traveled since the last ignition cycle for TRIP A or TRIP B. 197 Tire Pressures: Press the trip information button until TIRE PRESSURES appears on the display. This mode shows the tire pressure in pounds per square inch (psi) or kilopascals (kPa). Press the select button to scroll through the following information: (cid:127) LF TIRE shows the tire pressure for the front driver’s side tire. (cid:127) RF TIRE shows the tire pressure for the front passenger’s side tire. (cid:127) LR TIRE shows the tire pressure for the rear driver’s side tire.

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2007 Saab 9 7X Owners Manual