2006 Pontiac Grand PRIX Owners Manual

Download PDF Manual
badly that they will have to be replaced. Do not let someone put in the wrong kind of ﬂuid. If you spill brake ﬂuid on your vehicle’s painted surfaces, the paint ﬁnish can be damaged. Be careful not to spill brake ﬂuid on your vehicle. If you do, wash it off immediately. See Washing Your Vehicle on page 5-105.

5-43

(cid:127) Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving, except when you are pushing on the brake pedal ﬁrmly.

{CAUTION:

The brake wear warning sound means that soon your brakes will not work well. That could lead to an accident. When you hear the brake wear warning sound, have your vehicle serviced.

Notice: Continuing to drive with worn-out brake pads could result in costly brake repair. Some driving conditions or climates may cause a brake squeal when the brakes are ﬁrst applied or lightly applied. This does not mean something is wrong with your brakes. Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to GM torque speciﬁcations. Brake linings should always be replaced as complete axle sets. Brake Pedal Travel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign of brake trouble. Brake Adjustment Every time you apply the brakes, with or without the vehicle moving, your brakes adjust for wear.

5-44

Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts. When you replace parts of your braking system — for example, when your brake linings wear down and you need new ones put in — be sure you get new approved GM replacement parts. If you do not, your brakes may no longer work properly. For example, if someone puts in brake linings that are wrong for your vehicle, the balance between your front and rear brakes can change — for the worse. The braking performance you have come to expect can change in many other ways if someone puts in the wrong replacement brake parts.

Battery Your vehicle has a maintenance free battery. When it is time for a new battery, get one that has the replacement number shown on the original battery’s label. We recommend an ACDelco® replacement battery. See Engine Compartment Overview on page 5-12 for battery location.

Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. If the battery has a very low charge or is dead, you may not be able to remove the ignition key from the ignition switch or shift out of PARK (P). Refer to Shifting Out of Park (P) on page 2-32. Vehicle Storage If you are not going to drive your vehicle for 25 days or more, remove the black, negative (−) cable from the battery. This will help keep the battery from running down.

{CAUTION:

Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 5-46 for tips on working around a battery without getting hurt.

5-45

Jump Starting If your vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely.

{CAUTION:

Batteries can hurt you. They can be dangerous because:

(cid:127) They contain acid that can burn you. (cid:127) They contain gas that can explode

(cid:127) They contain enough electricity to

or ignite.

burn you.

If you do not follow these steps exactly, some or all of these things can hurt you.

5-46

Ignoring these steps could result in costly

Notice: damage to your vehicle that would not be covered by your warranty. Trying to start your vehicle by pushing or pulling it will not work, and it could damage your vehicle. 1. Check the other vehicle. It must have a 12-volt

battery with a negative ground system.

If the other vehicle’s system is not a 12-volt

Notice: system with a negative ground, both vehicles can be damaged. Only use vehicles with 12-volt systems with negative grounds to jump start your vehicle. 2. Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles are not touching each other. If they are, it could cause a ground connection you do not want. You would not be able to start your vehicle, and the bad grounding could damage the electrical systems. To avoid the possibility of the vehicles rolling, set the parking brake ﬁrmly on both vehicles involved in the jump start procedure. Put an automatic transaxle in PARK (P) or a manual transaxle in NEUTRAL before setting the parking brake.

If you leave your radio or other accessories

Notice: on during the jump starting procedure, they could be damaged. The repairs would not be covered by your warranty. Always turn off your radio and other accessories when jump starting your vehicle. 3. Turn off the ignition on both vehicles. Unplug

unnecessary accessories plugged into the cigarette lighter or the accessory power outlet. Turn off the radio and all lamps that are not needed. This will avoid sparks and help save both batteries. And it could save the radio!

4. Open the hood on the other vehicle and locate the positive (+) and negative (−) terminal locations on that vehicle. You will not use your vehicle’s battery for jump starting. It has a remote positive (+) jump starting terminal, located on the underhood fuse block, for that purpose.

3800 V6 and 3800 V6
Supercharged Engines

If your vehicle has one of the 3800 V6 engines, to uncover the remote positive (+) terminal, press the tab at the bottom of the fuse block and lift the cover up.

5-47

If your vehicle has the 5.3L V8 engine, to uncover the remote positive (+) terminal, remove the fuse block cover.

5.3L V8 Engine

Always use the remote positive (+) terminal instead of the positive (+) terminal on the battery. See Engine Compartment Overview on page 5-12 for more information on location.

{CAUTION:

An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.

5-48

{CAUTION:

Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running.

{CAUTION:

Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle. But if a battery has ﬁller caps, be sure the right amount of ﬂuid is there. If it is low, add water to take care of that ﬁrst. If you do not, explosive gas could be present. Battery ﬂuid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, ﬂush the place with water and get medical help immediately.

5. Check that the jumper cables do not have loose or

missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know. Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one. Negative will go to a heavy, unpainted metal engine part or to a remote negative (−) terminal if the vehicle has one. Do not connect positive (+) to negative (−), or you will get a short that would damage the battery and maybe other parts too. And do not connect the negative (−) cable to the negative (−) terminal on the dead battery because this can cause sparks.

6. Connect the red positive (+) cable to the positive (+)

terminal location on the vehicle with the dead battery. Use a remote positive (+) terminal if the vehicle has one.

7. Do not let the other end touch metal. Connect it to the positive (+) terminal location on the vehicle with the good battery. Use a remote positive (+) terminal if the vehicle has one.

8. Now connect the black negative (−) cable to the negative (−) terminal location on the vehicle with the good battery. Use a remote negative (−) terminal if the vehicle has one. Do not let the other end touch anything until the next step. The other end of the negative (−) cable does not go to the dead battery. It goes to a heavy, unpainted metal engine part or to a remote negative (–) terminal on the vehicle with the dead battery.

9. Connect the other end of the negative (−) cable at

least 18 inches (45 cm) away from the dead battery, but not near engine parts that move. The electrical connection is just as good there, and the chance of sparks getting back to the battery is much less.

10. Now start the vehicle with the good battery and run

the engine for a while.

11. Try to start the vehicle that had the dead battery.

If it will not start after a few tries, it probably needs service.

5-49

If the jumper cables are connected or

Notice: removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.

Jumper Cable Removal

A. Heavy, Unpainted Metal Engine Part or Remote

Negative (−) Terminal

B. Good Battery or Remote Positive (+) and Remote

Negative (−) Terminals

C. Dead Battery or Remote Positive (+) Terminal

5-50

To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the

vehicle that had the dead battery.

2. Disconnect the black negative (−) cable from the

vehicle with the good battery.

3. Disconnect the red positive (+) cable from the

vehicle with the good battery.

4. Disconnect the red positive (+) cable from the

other vehicle.

5. Return the remote positive (+) terminal cover to its

original position.

Headlamp Aiming The vehicle has a visual optical headlamp aiming system. The aim has been preset at the factory and should need no further adjustment. However, If the vehicle is damaged in an accident, the headlamp aim may be affected and adjustment may be necessary. If oncoming vehicles ﬂash their high beams at you, this may also mean the vertical aim needs to be adjusted.

It is recommended that the vehicle is taken to your dealer for service if the headlamps need to be re-aimed. It is possible however, to re-aim the headlamps as described in the following procedure. The vehicle should be properly prepared as follows:

Headlamp aiming is done with the low-beam headlamps. The high-beam headlamps will be correctly aimed if the low-beam headlamps are aimed properly. To adjust the vertical aim, do the following:

The vehicle should be placed so the headlamps are 25 ft. (7.6 m) from a light colored wall or other ﬂat surface. The vehicle must have all four tires on a perfectly level surface which is level all the way to the wall or other ﬂat surface. The vehicle should be placed so it is perpendicular to the wall or other ﬂat surface. The vehicle should not have any snow, ice, or mud on it. The vehicle should be fully assembled and all other work stopped while headlamp aiming is being done. The vehicle should be normally loaded with a full tank of fuel and one person or 160 lbs (75 kg) sitting on the driver’s seat. Tires should be properly inﬂated.

1. Find the aim dot on the lens of the low-beam lamp. 2. Measure the distance from the ground to the aim

dot on the lamp. Record the distance.

3. At the wall or other ﬂat surface, measure from the ground upward the recorded distance from Step 2
and draw or tape a horizontal line the width of the vehicle.

5-51

(cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) (cid:127) 4. Turn on the low-beam headlamps and place a piece of cardboard or equivalent in front of the headlamp not being aimed. This should allow only the beam of light from the headlamp being aimed to be seen on the ﬂat surface.

Notice: Do not cover a headlamp to improve beam cut-off when aiming. Covering a headlamp may cause excessive heat build-up which may cause damage to the headlamp.

Driver’s Side shown

5. Locate the vertical headlamp aiming screws, which are under the hood, near the headlamps. Turn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line. The adjustment screws can be turned with a 6 mm hex key bit socket or a 6 mm hex key.

5-52

6. Ensure the top edge of the cut-off is positioned at

the bottom edge of the horizontal tape line. 7. Repeat Steps 4 through 6 for the opposite

headlamp.

Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-59. For any bulb changing procedure not listed in this section, contact your dealer.

Halogen Bulbs

{CAUTION:

Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.

5-53

Headlamps and Sidemarker Lamps To replace a headlamp or sidemarker bulb, do the following: 1. Open the hood. See Hood Release on page 5-11

for more information.

A. High-Beam Headlamp B. Low-Beam Headlamp C. Sidemarker Lamp

5-54

2. Locate the metal retaining clip. Remove the bolt. 3. Pull up half-way on the metal retaining clip while pushing rearward on the headlamp. Align the square cut-out on the retaining clip with the notch on the headlamp.

4. Pull the headlamp assembly straight out from the

vehicle. (Moving the headlamp up and down slightly may help with its removal.)

A. High-Beam Headlamp B. Low-Beam Headlamp C. Sidemarker Lamp

5. Turn the bulb socket ring one-quarter of a turn

counterclockwise to remove it from the headlamp assembly.

6. Pull the old bulb from the socket. 7. Place the new bulb into the socket. 8. Turn the bulb socket ring one-quarter turn clockwise

to reinstall it back into the headlamp assembly.

5-55

9. Carefully reinstall the headlamp assembly. 10. Push down on the metal retaining clip while pushing

rearward on the headlamp, making sure the headlamp assembly is secure.

11. Reinstall the bolt and tighten to secure.

Front Turn Signal, Parking and Fog Lamps The front turn signal, parking, and fog lamps (if equipped) are located below the headlamp assembly.

To replace one of these bulbs, do the following: 1. Follow Steps 1 through 4 of the headlamp

replacement procedure. See Headlamps and Sidemarker Lamps on page 5-54 for more information.

2. Locate the front turn

signal/parking lamp (all models) and fog lamp bulbs (if equipped), which are located below the headlamp assembly.

The arrow indicates which is the turn signal/parking lamp bulb. The fog lamp bulb is below it, if your vehicle has this bulb. If you need to have fog lamp bulb replaced, see your dealer for service.

3. Turn the bulb socket one-quarter of a turn

counterclockwise to remove it from its assembly.

4. Pull the old bulb from the socket and replace it with

a new one.

5. Turn the bulb socket a quarter turn clockwise to

reinstall it.

A. Front Turn Signal/Parking Lamp B. Fog Lamp (If Equipped)

5-56

6. Reinstall the headlamp assembly. 7. Push down on the metal retaining clip while pushing

rearward on the headlamp, making sure the headlamp assembly is secure.

8. Reinstall the bolt and tighten to secure.

2. Remove the convenience net, if equipped, by

removing the net hook attachments.

3. Remove the plastic cap from the trunk trim. 4. Pull the trunk trim and carpet away from the back of

the trunk.

Taillamps, Turn Signal, and Stoplamps

A. Taillamp B. Taillamps, Turn Signal

and Stoplamps

5. Remove the bottom bolt and two nuts.

6. Remove the taillamp assembly by pulling it out from the vehicle.

1. Open the trunk. See Trunk on page 2-13 for more

information.

5-57

7. Turn the appropriate

lamp socket a quarter turn counterclockwise and remove it.

Back-Up Lamps The back-up lamps are located on the trunk lid.

8. Remove the old bulb. 9. Replace with a new bulb into the socket and turn

the lamp socket clockwise to install it.

10. Reinstall the taillamp assembly by reversing

Steps 2 through 5.

To replace the back-up lamp bulb(s), do the following: 1. Open the trunk. See Trunk on page 2-13 for

more information.

5-58

Replacement Bulbs

Exterior Lamps

Back-Up Lamp

Front Parking/Turn Signal Lamp

Front Sidemarker Headlamps

High-Beam Halogen Low-Beam Halogen

Bulb Number

3157

3757 KA* or 5702 KA**

194

9005
9006
3057

Stop/Taillamp/Turn Signal Lamps * GT and Base Models with the Optional Fog Lamps * For Lamps Not Equipped with the Fog Function and GXP Models

2. Turn the appropriate lamp socket a quarter turn

counterclockwise and remove it.

3. Remove the old bulb. 4. Put the new bulb into the lamp socket. 5. Turn the bulb a quarter turn clockwise to reinstall it.

For replacement bulbs not listed here, contact your dealer.

5-59

Windshield Replacement If your vehicle is equipped with the Head-Up Display (HUD) system, keep in mind that your windshield is part of the HUD system. If you ever have to get your windshield replaced, be sure to get one that is designed for HUD or your HUD image may look blurred or out of focus. Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See Scheduled Maintenance on page 6-4
for more information on wiper blade inspection. Replacement blades come in different types and are removed in different ways. For the proper type and length, see Normal Maintenance Replacement Parts on page 6-13. Here’s how to remove the wiper blade: 1. Pull the windshield wiper arm connector away from

the windshield.

5-60

2. While holding the wiper arm, pull the clip up from

the blade connecting point, and pull the blade assembly down toward the windshield to remove it from the wiper arm.

3. Install the new wiper blade onto the wiper arm and

snap the clip into place.

Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s owner manual.

{CAUTION:

Poorly maintained and improperly used tires are dangerous.

(cid:127) Overloading your tires can cause

overheating as a result of too much friction. You could have an air-out and a serious accident. See Loading Your Vehicle on page 4-33.

(cid:127) Underinﬂated tires pose the same

danger as overloaded tires. The resulting accident could cause serious injury. Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your tires are cold. See Inﬂation - Tire Pressure on page 5-67.

(cid:127) Overinﬂated tires are more likely to be cut,

punctured, or broken by a sudden impact — such as when you hit a pothole. Keep tires at the recommended pressure.

(cid:127) Worn, old tires can cause accidents. If

your tread is badly worn, or if your tires have been damaged, replace them.

Low-Proﬁle Performance Tire (GXP) If your vehicle has P255/45R18 size tires on the front wheels and P225/50R18 size tires on the rear wheels, they are classiﬁed as low-proﬁle performance tires. These tires are designed for very responsive driving on wet or dry pavement. You may also notice more road noise with low-proﬁle performance tires and that they tend to wear faster. Notice: are more susceptible to damage from road hazards or curb impact than standard proﬁle tires. Tire and/or wheel assembly damage can occur when coming into contact with road hazards like, potholes, or sharp edged objects, or when sliding into a curb. Your GM warranty does not cover this type of damage. Keep tires set to the correct inﬂation pressure and, when possible avoid contact with curbs, potholes, and other road hazards.

If your vehicle has low-proﬁle tires, they

5-61

Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall.

Passenger (P-Metric) Tire Example

(A) Tire Size: The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description. See the “Tire Size” illustration later in this section for more detail.

5-62

(B) TPC Spec (Tire Performance Criteria Speciﬁcation): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC speciﬁcation code molded onto the sidewall. GM’s TPC speciﬁcations meet or exceed all federal safety guidelines. (C) DOT (Department of Transportation): The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor Vehicle Safety Standards. (D) Tire Identiﬁcation Number (TIN): The letters and numbers following DOT (Department of Transportation) code is the Tire Identiﬁcation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction, and temperature resistance. For more information see Uniform Tire Quality Grading on page 5-74. (G) Maximum Cold Inﬂation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load.

(B) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (C) Tire Identiﬁcation Number (TIN): The letters and numbers following the DOT (Department of Transportation) code is the Tire Identiﬁcation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (D) Maximum Cold Inﬂation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load. (E) Tire Inﬂation: The temporary use tire or compact spare tire should be inﬂated to 60 psi (420 kPa). For more information on tire pressure and inﬂation see Inﬂation - Tire Pressure on page 5-67. (F) Tire Size: A combination of letters and numbers deﬁne a tire’s width, height, aspect ratio, construction type and service description. The letter T as the ﬁrst character in the tire size means the tire is for temporary use only. (G) TPC Spec (Tire Performance Criteria Speciﬁcation): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC speciﬁcation code molded onto the sidewall. GM’s TPC speciﬁcations meet or exceed all federal safety guidelines.

5-63

Compact Spare Tire Example

(A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone ﬂat. If your vehicle has a compact spare tire, see Compact Spare Tire on page 5-99
and If a Tire Goes Flat on page 5-77.

Tire Size The following illustration shows an example of a typical passenger vehicle tire size.

(A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U.S. Tire and Rim Association.

(B) Tire Width: The three-digit number indicates the tire section width in millimeters from sidewall to sidewall.

(C) Aspect Ratio: A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire’s sidewall is 60 percent as high as it is wide.

5-64

(D) Construction Code: A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted-bias ply construction.

(E) Rim Diameter: Diameter of the wheel in inches.

(F) Service Description: These characters represent the load range and speed rating of the tire. The load index represents the load carry capacity a tire is certiﬁed to carry. The load index can range from 1 to 279. The speed rating is the maximum speed a tire is certiﬁed to carry a load. Speed ratings range from A to Z.

Tire Terminology and Deﬁnitions

Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa).

Accessory Weight: This means the combined weight of optional accessories. Some examples of optional accessories are, automatic transmission, power steering, power brakes, power windows, power seats, and air conditioning.

Aspect Ratio: The relationship of a tire’s height to its width.

Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials.

Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim.

Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.

Cold Inﬂation Pressure: The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. See Inﬂation - Tire Pressure on page 5-67.

Curb Weight: This means the weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil and coolant, but without passengers and cargo.

DOT Markings: A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) motor vehicle safety standards. The DOT code includes the Tire Identiﬁcation Number (TIN), an alphanumeric designator which can also identify the tire manufacturer, production plant, brand and date of production.

GVWR: Gross Vehicle Weight Rating, see Loading Your Vehicle on page 4-33.

GAWR FRT: Gross Axle Weight Rating for the front axle, see Loading Your Vehicle on page 4-33.

GAWR RR: Gross Axle Weight Rating for the rear axle, see Loading Your Vehicle on page 4-33.

Intended Outboard Sidewall: The side of an asymmetrical tire, that must always face outward when mounted on a vehicle.

Kilopascal (kPa): The metric unit for air pressure.

Light Truck (LT-Metric) Tire: A tire used on light duty trucks and some multipurpose passenger vehicles.

Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire.

Maximum Inﬂation Pressure: The maximum air pressure to which a cold tire may be inﬂated. The maximum air pressure is molded onto the sidewall.

Maximum Load Rating: The load rating for a tire at the maximum permissible inﬂation pressure for that tire.

Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight.

Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 150 lbs (68 kg). See Loading Your Vehicle on page 4-33.

5-65

Occupant Distribution: Designated seating positions.

Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire.

Passenger (P-Metric) Tire: A tire used on passenger cars and some light duty trucks and multipurpose vehicles.

Recommended Inﬂation Pressure: Vehicle manufacturer’s recommended tire inﬂation pressure and shown on the tire placard. See Inﬂation - Tire Pressure on page 5-67 and Loading Your Vehicle on page 4-33.

Radial Ply Tire: A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread.

Rim: A metal support for a tire and upon which the tire beads are seated.

Sidewall: The portion of a tire between the tread and the bead.

Speed Rating: An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate.

5-66

Traction: The friction between the tire and the road surface. The amount of grip provided. Tread: The portion of a tire that comes into contact with the road. Treadwear Indicators: Narrow bands, sometimes called wear bars, that show across the tread of a tire when only 1/16 inch (1.6 mm) of tread remains. See When It Is Time for New Tires on page 5-71. UTQGS (Uniform Tire Quality Grading Standards): A tire information system that provides consumers with ratings for a tire’s traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 5-74. Vehicle Capacity Weight: The number of designated seating positions multiplied by 150 lbs (68 kg) plus the rated cargo load. See Loading Your Vehicle on page 4-33. Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. Vehicle Placard: A label permanently attached to a vehicle showing the vehicle’s capacity weight and the original equipment tire size and recommended inﬂation pressure. See “Tire and Loading Information Label” under Loading Your Vehicle on page 4-33.

Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inﬂation or over-inﬂation is all right. It is not. If your tires do not have enough air (under-inﬂation), you can get the following:

Too much ﬂexing Too much heat Tire overloading

(cid:127) Premature or irregular wear (cid:127) Poor handling (cid:127) Reduced fuel economy If your tires have too much air (over-inﬂation), you can get the following: (cid:127) Unusual wear (cid:127) Poor handling (cid:127) Rough ride (cid:127) Needless damage from road hazards

A Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar), below the driver’s door latch. This label shows your vehicle’s original equipment tires and the correct inﬂation pressures for your tires when they are cold. The recommended cold tire inﬂation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle’s maximum load carrying capacity. For additional information regarding how much weight your vehicle can carry, and an example of the tire and loading information label, see Loading Your Vehicle on page 4-33. How you load your vehicle affects vehicle handling and ride comfort, never load your vehicle with more weight than it was designed to carry. When to Check Check your tires once a month or more. Do not forget to check the compact spare tire, it should be at 60 psi (420 kPa). For additional information regarding the compact spare tire, see Compact Spare Tire on page 5-99.

5-67

(cid:127) (cid:127) (cid:127) Tire Inﬂation Monitor System Your vehicle may have the Tire Inﬂation Monitor System (TIMS). The system is designed to alert the driver when there is a large air pressure change in one tire, while the vehicle is being driven. TIMS detects differences in tire rotation speeds that are caused by changes in tire pressure. The system can alert you about a low tire but it does not replace normal tire maintenance. See Tires on page 5-60. The TIMS learns the pressure at each tire throughout the operating speed range of the vehicle. The system normally takes between 45 and 90 minutes of driving to learn the tire pressures. This time may be longer depending on individual driving habits. Learning need not be accumulated during a single trip. Once learned, the system will remember the tire pressures until the system is reset.

How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are under-inﬂated. Check the tire’s inﬂation pressure when the tires are cold. Cold means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). Remove the valve cap from the tire valve stem. Press the tire gage ﬁrmly onto the valve to get a pressure measurement. If the cold tire inﬂation pressure matches the recommended pressure on the Tire and Loading Information label, no further adjustment is necessary. If the inﬂation pressure is low, add air until you reach the recommended amount. If you overﬁll the tire, release air by pushing on the metal stem in the center of the tire valve. Re-check the tire pressure with the tire gage. Be sure to put the valve caps back on the valve stems. They help prevent leaks by keeping out dirt and moisture.

5-68

This symbol, along with the CHECK TIRE PRESSURE warning message, will appear in the Driver Information Center (DIC) if the pressure in one tire becomes 12 psi (83 kPa) lower than the other three tires.

See DIC Warnings and Messages on page 3-72 for more information. The tire inﬂation monitor system will not alert you if the pressure in more than one tire is low, if the system is not properly calibrated, or if the vehicle is moving faster than 70 mph (110 km/h). When the CHECK TIRE PRESSURE warning message comes on, stop as soon as possible and check all the tires for damage. If a tire is ﬂat, see If a Tire Goes Flat on page 5-77. Also, check the tire pressure in all four tires as soon as possible. See Inﬂation - Tire Pressure on page 5-67.

The CHECK TIRE PRESSURE warning message will also be displayed, while the ignition is on, until the system is reset. To reset the system, see “Tire Inﬂation Monitor System” under the options mode in DIC Controls and Displays (Base Level DIC) on page 3-52
or DIC Controls and Displays (Uplevel DIC with Trip Computer) on page 3-60. Do not reset the tire inﬂation monitor system without ﬁrst correcting the cause of the problem and checking and adjusting the pressure in all four tires. If the system is reset when the tire pressures are incorrect, the system will not work properly and may not respond when a tire is low. The tire inﬂation monitor system will need to be reset any time a tire’s pressure is adjusted, the tires are rotated, or one or more tires is repaired or replaced. The system will also need to be reset when new tires are purchased for the vehicle and when the battery has been disconnected.

5-69

Tire Inspection and Rotation Tire rotation is not recommended if your vehicle is a GXP model equipped with P255/45R18 size tires on the front wheels and P225/50R18 size tires on the rear wheels. Different tire sizes front to rear should not be rotated. Tire rotation is recommended if the original equipment tires installed on your vehicle are of the same size and type on all four tire/wheel positions. Original equipment tires of the same size and type should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km). Any time you notice unusual wear, rotate your vehicle’s tires as soon as possible and check the wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 5-71 and Wheel Replacement on page 5-75 for more information. The purpose of regular rotation is to achieve more uniform wear for all tires on the vehicle. The ﬁrst rotation is the most important. See Scheduled Maintenance on page 6-4 for scheduled rotation intervals.

5-70

Rotation Pattern for Non-GXP Tires Only

The correct rotation pattern shown here is only for non-GXP tires. Do not include the compact spare tire, if equipped, in your vehicle’s tire rotation. After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Tire and Loading Information label, and reset the Tire Inﬂation Monitor System. See Tire Inﬂation Monitor System on page 5-68 for additional information.

Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Speciﬁcations on page 5-118.

{CAUTION:

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off. See Changing a Flat Tire on page 5-88.

When It Is Time for New Tires

One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining.

You need a new tire if any of the following statements are true: (cid:127) You can see the indicators at three or more places

around the tire.

(cid:127) You can see cord or fabric showing through the

tire’s rubber. The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric. The tire has a bump, bulge, or split. The tire has a puncture, cut or other damage that cannot be repaired well because of the size or location of the damage.

5-71

(cid:127) (cid:127) (cid:127) Buying New Tires GM has developed and matched speciﬁc tires for your vehicle. The original equipment tires installed on your vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Speciﬁcation (TPC spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating. This way, your vehicle will continue to have tires that are designed to give the same performance and vehicle safety, during normal use, as the original tires. GM’s exclusive TPC Spec system considers over a dozen critical speciﬁcations that impact the overall performance of your vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM’s TPC Spec number is molded onto the tire’s sidewall by the tire manufacturer. If the tires have an all-season tread design, the TPC spec number will be followed by an MS for mud and snow. See Tire Sidewall Labeling on page 5-62 for additional information.

{CAUTION:

Mixing tires could cause you to lose control while driving. If you mix tires of different sizes (other than those originally installed on your vehicle), brands, or types (radial and bias-belted tires), the vehicle may not handle properly, and you could have a crash. Using tires of different sizes (other than those originally installed on your vehicle) may also cause damage to your vehicle. Be sure to use the correct size, brand, and type tires on all wheels. If your vehicle has a compact spare tire, it is all right to drive your vehicle with the compact spare temporarily. It was developed for use on your vehicle. See Compact Spare Tire on page 5-99.

5-72

{CAUTION:

If you use bias-ply tires on your vehicle, the wheel rim ﬂanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on your vehicle.

If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction type (radial and bias-belted tires) as your vehicle’s original tires. Your vehicle’s original equipment tires are listed on the Tire and Loading Information Label. This label is attached to the vehicle’s center pillar (B-pillar). See Loading Your Vehicle on page 4-33, for more information about the Tire and Loading Information Label and its location on your vehicle.

Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability and resistance to rollover. Additionally, if your vehicle has electronic systems such as, antilock brakes; traction control; and electronic stability control, the performance of these systems can be affected.

{CAUTION:

If you add different sized wheels, your vehicle may not provide an acceptable level of performance and safety if tires not recommended for those wheels are selected. You may increase the chance that you will crash and suffer serious injury. Only use GM speciﬁc wheel and tire systems developed for your vehicle, and have them properly installed by a GM certiﬁed technician.

See Buying New Tires on page 5-72 and Accessories and Modiﬁcations on page 5-3 for additional information.

5-73

Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance. (This applies only to vehicles sold in the United States.) The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading system does not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards.

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart signiﬁcantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on speciﬁed government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.

5-74

Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inﬂated and not overloaded. Excessive speed, underinﬂation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if you notice unusual tire wear or your vehicle pulling to one side or the other, the alignment may need to be checked. If you notice your vehicle vibrating when driving on a smooth road, your tires and wheels may need to be rebalanced. See your dealer for proper diagnosis.

Wheel Replacement Replace any wheel that is bent, cracked or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your dealer if any of these conditions exist. Your dealer will know the kind of wheel you need.

5-75

Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle.

Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. See Changing a Flat Tire on page 5-88 for more information. Used Replacement Wheels

{CAUTION:

Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured. Always use the correct wheel, wheel bolts and wheel nuts for replacement.

{CAUTION:

Putting a used wheel on your vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.

5-76

Tire Chains

{CAUTION:

If your vehicle has P225/55R17, P255/45R18 or P225/50R18 size tires, do not use tire chains, there is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash. Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions. Follow that manufacturer’s instructions. To help avoid damage to your vehicle, drive slowly, readjust or remove the device if it is contacting your vehicle, and do not spin your wheels. If you do ﬁnd traction devices that will ﬁt, install them on the front tires.

Notice: If your vehicle does not have P225/55R17, P255/45R18 or P225/50R18 size tires, use tire chains only where legal and only when you must. Use only SAE Class S-type chains that are the proper size for your tires. Install them on the front tires and tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer’s instructions. If you can hear the chains contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage your vehicle.

If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your tires properly. See Tires on page 5-60. If air goes out of a tire, it is much more likely to leak out slowly. But if you should ever have a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the ﬂat tire will create a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel ﬁrmly. Steer to maintain lane position, and then gently brake to a stop well out of the traffic lane.

5-77

A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you’d use in a skid. In any rear blowout, remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy, but you can still steer. Gently brake to a stop, well off the road if possible. If a tire goes ﬂat, and your vehicle has a spare tire, see Changing a Flat Tire on page 5-88. This information shows you how to use your vehicle’s tire changing equipment and how to change a ﬂat tire safely.

{CAUTION:

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. The jack provided with your vehicle is designed only for changing a ﬂat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. Use the jack provided with your vehicle only for changing a ﬂat tire.

If a Tire Goes Flat (GXP) GXP models have no spare tire, no tire changing equipment, and no place for storing a spare or ﬂat tire. If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place and stopping. Then do this: 1. Turn on the hazard warning ﬂashers. See Hazard

Warning Flashers on page 3-6.

2. Park your vehicle. Set the parking brake ﬁrmly and

put the shift lever in PARK (P). See Shifting Into Park (P) on page 2-31 for additional information.

3. Turn off the engine. 4. Inspect the ﬂat tire. If the tire has been separated from the wheel or has damaged sidewalls or large tears that allow rapid air loss, call a tire repair facility. See Roadside Assistance Program on page 7-6. If the ﬂat tire is due to a slow leak caused by a nail or other similar road hazard, the tire inﬂator kit may be used to temporarily repair the damaged tire. The kit uses a liquid tire sealant to seal small punctures in the tread area of the tire. The ﬂat tire is then inﬂated to at least 30 psi (207 kPa) and driven to evenly distribute the tire sealant.

5-78

If the tire pressure has dropped below

The tire pressure is checked after driving for a maximum of ﬁve miles (8.0 km) to see if the slow leak has been stopped. If the tire pressure is 19 psi (131 kPa) or more, inﬂate the tire up to the standard operating pressure as shown on the tire and loading information label. This label is attached to the vehicle’s center-pillar below the driver’s door latch. See Inﬂation - Tire Pressure on page 5-67. Notice: 19 psi (131 kPa), the vehicle should not be driven. Damage to the tire may be severe and the sealant will not be effective. Contact Roadside Assistance, see Roadside Assistance Program on page 7-6. You should have the damaged tire repaired as soon as possible. The tire sealant is a temporary repair only. If the tire has been ﬁlled with tire sealant, take the tire to a GM dealer for inspection and repair. See Tire Inﬂator Kit (GXP) on page 5-79 for additional information.

Tire Inﬂator Kit (GXP) Your vehicle may have a tire inﬂator kit. The kit uses a liquid tire sealant and air at the same time to seal small punctures in the tread area of the tire. Be sure to read and follow all the tire inﬂator kit instructions. The kit includes the following:

A. Air Compressor B. Tire Sealant Canister C. Air Compressor Accessory Plug

D. On/Off Switch

E. Air Pressure Gage F. Air Compressor

Inﬂator Hose

G. Sealant Filling Hose

If the ﬂat tire is due to a slow leak caused by a nail or other similar road hazard, the tire inﬂator kit may be used to temporarily repair the damaged tire. After temporarily repairing a tire with the tire inﬂator kit, take your vehicle to an authorized GM dealer to have the tire inspected and repaired.

5-79

Accessing the Tire Inﬂator Kit To access the tire inﬂator kit, do the following: 1. Open the trunk. See Trunk on page 2-13 for more

information.

2. Locate the tire inﬂator kit by lifting up the carpet. 3. Remove the inﬂator kit cover by turning the center nut counterclockwise.

5-80

4. Remove the inﬂator kit by pulling it straight out of

the foam container.

Tire Sealant The kit contains a liquid sealant that when injected into a ﬂat tire, may temporarily repair nail holes or cuts in the tread area of the tire. The tire sealant cannot repair tire damage caused while driving on a ﬂat tire or a tire that has had a “blow out” or a tire that has punctures in the sidewall areas. The tire sealant solution is to be used for a single tire and can only be used once. Check the tire sealant expiration date on the sealant canister. The sealant may not be as effective beyond the expiration date. If needed, see your GM dealer for a replacement canister. After temporarily repairing a tire using the tire sealant, take your vehicle to an authorized GM dealer to have the tire inspected and repaired.

Using the Tire Inﬂator Kit To use the tire inﬂator kit, do the following: 1. Place the inﬂator kit on the ground and unwrap the

sealant ﬁlling hose from the compressor.

2. Remove the air compressor accessory plug from

the unit. To do this, pull the top portion of the wrapped cord out ﬁrst, then the bottom, then unsnap the plug. Do not insert the plug into an accessory outlet yet.

3. Remove the valve stem cap from the ﬂat tire by

turning it counterclockwise. If an object, such as a nail, has penetrated the tire, do not remove it.

5-81

{CAUTION:

Idling the engine in a closed-in place or with the climate control system off can cause deadly carbon monoxide (CO). See Engine Exhaust on page 2-33.

6. Start the vehicle. See Starting the Engine on

page 2-23 for more information. The vehicle must be running while using the air compressor.

{CAUTION:

Inﬂating something too much can make it explode, and you or others could be injured. Be sure to read the inﬂator instructions, and inﬂate the tire to its recommended pressure. Do not exceed 36 psi (248 kPa).

7. Move the inﬂator kit switch to the I (on) position. The inﬂator kit will force sealant and air into the tire. Sealant may leak from the puncture hole until the vehicle is driven and the hole has sealed.

4. Attach the sealant ﬁlling hose (A) onto the tire valve

stem. Turn it clockwise until it is tight. Make sure the inﬂator kit on/off switch (B) is in the O (off) position.

5. Plug the air compressor accessory plug (C) into an

accessory power outlet in the vehicle. See Accessory Power Outlet(s) on page 3-24 for more information.

5-82

10. Move the inﬂator kit switch to the O (off) position

once the correct tire pressure is obtained.

11. Turn off the engine. 12. Unplug the air compressor accessory plug from the

accessory power outlet in the vehicle.

13. Disconnect the sealant ﬁlling hose from the tire valve stem, by turning it counterclockwise, and replace the tire valve stem cap. Be careful when handling the tire inﬂator components as they may be hot after usage.

14. Wrap the sealant ﬁlling hose around the air

compressor channel to stow it in its original location.

8. Make sure there is a proper connection between the tire valve stem and the sealant ﬁlling hose by looking at the air pressure gage. If there is not a pressure reading while the compressor is running, the connection between the inﬂator kit and the tire is bad. Check the attachment between the sealant ﬁlling hose and the tire valve stem.

9. Inﬂate the tire up to the recommended inﬂation

pressure, found on the Tire and Loading Information label located on the vehicle’s center pillar (B-pillar) below the vehicle’s door latch, using the air pressure gage on the top of the unit as a guide. The pressure gage reading is slightly high while the compressor is on. Turn the compressor off to get an accurate pressure reading.

If the recommended pressure cannot be

Notice: reached after 15 minutes, the vehicle should not be driven farther. Damage to the tire is severe and the sealant will not be effective. Remove the air compressor plug from the accessory power outlet and unscrew the inﬂating hose from the tire valve. See Roadside Assistance Program on page 7-6.

5-83

15. Stow the air compressor accessory plug back in the air compressor. To do this, wrap the air compressor accessory plug, snap in the plug, and then push in the bottom and then the top of the wrapped air compressor accessory plug.

16. If the ﬂat tire was able

to inﬂate to the recommended inﬂation pressure, remove the maximum speed label from the sealant canister.

{CAUTION:

Storing the tire inﬂator kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire inﬂator kit in the proper place.

17. Return the equipment to the proper storage location

in the trunk of your vehicle.

Place it in a highly visible location such as the inside of the upper left corner of the windshield or to the face of the radio/clock. The maximum speed label reminds you to drive cautiously and not to exceed 55 mph (90 km/h) until you have the damaged tire inspected and repaired.

5-84

18. Immediately drive the vehicle 5 miles (8 km) to

distribute the sealant evenly in the tire. Stop at a safe location and check the tire pressure. Refer to Steps 1 through 8 under “Using the Air Compressor without Sealant” next in this section. If the tire pressure has fallen more than 10 psi (68 kPa) below the recommended inﬂation pressure, stop driving the vehicle. The tire is too damaged for the sealant to work. See Roadside Assistance Program on page 7-6. If the tire pressure has not dropped more than 10 psi (68 kPa) from the recommended inﬂation pressure, you can inﬂate the tire back up to the recommended inﬂation pressure.

19. Dispose of the sealant canister at a local GM dealer

or in accordance with your local state codes and practices. After using the sealant canister, replace it with a new canister from a GM dealer.

20. After temporarily repairing a tire with the emergency ﬂat tire repair kit, take your vehicle to an authorized GM dealer to have the tire inspected and repaired.

Using the Air Compressor without Sealant To use the air compressor by itself to inﬂate a tire, do the following: 1. Remove the air compressor accessory plug from

the air compressor.

2. Unlock the air compressor hose from the sealant

canister by pulling up on the lever.

5-85

3. Pull the air compressor inﬂator hose from the

sealant canister.

4. Push the air compressor inﬂator hose onto the

tire valve stem and push the lever down to secure in place.

5. Plug the air compressor accessory plug into an

accessory power outlet in the vehicle. See Accessory Power Outlet(s) on page 3-24 for more information.

{CAUTION:

Idling the engine in a closed-in place or with the climate control system off can cause deadly carbon monoxide (CO). See Engine Exhaust on page 2-33.

6. Start the vehicle. See Starting the Engine on

page 2-23 for more information. The vehicle must be running while using the air compressor.

{CAUTION:

Inﬂating something too much can make it explode, and you or others could be injured. Be sure to read the inﬂator instructions, and inﬂate the tire to its recommended pressure. Do not exceed 36 psi (248 kPa).

7. Move the inﬂator kit switch to the I (on) position. 8. Make sure there is a proper connection between the

tire valve stem and the air compressor hose by looking at the air pressure gage. If there is not a pressure reading while the compressor is running, the connection between the inﬂator kit and the tire is bad. Check the attachment between the air compressor hose and the tire valve stem.

9. Inﬂate the tire up to the recommended inﬂation pressure using the air pressure gage on the top of the unit as a guide.

10. Turn off the air compressor by moving the switch to

the O (off) position.

5-86

Removal and Installation of the Sealant Canister To remove the sealant canister, do the following:

{CAUTION:

Storing the tire inﬂator kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire inﬂator kit in the proper place.

11. Disconnect the compressor inﬂator hose and wrap

the hose in the bottom of the inﬂator kit.

12. Place the equipment in the original location in the

trunk of your vehicle.

1. Unlock the air compressor inﬂator hose from the

sealant canister by pulling the lever up.

2. Disconnect the air compressor inﬂator hose from

the sealant canister.

3. Unwrap the sealant ﬁlling hose from the

compressor.

5-87

To install a new sealant canister, do the following: 1. Align the sealant ﬁlling hose with the slot in the air

compressor.

2. Push the sealant canister down and rotate it

clockwise.

3. Wrap the sealant ﬁlling hose around the air

compressor channel to stow it in its original location.

4. Push the air compressor inﬂator hose onto the sealant canister inlet and push the lever down.

Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your vehicle’s hazard warning ﬂashers. See Hazard Warning Flashers on page 3-6 for more information.

4. Turn the sealant canister so the inﬂator ﬁlling hose

is aligned with the slot in the compressor.

5. Lift the sealant canister from the air compressor

and replace with a new sealant canister. See your GM dealer for more information.

5-88

{CAUTION:

Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving:

1. Set the parking brake ﬁrmly. 2. Put the shift lever in PARK (P). 3. Turn off the engine and do not restart

while the vehicle is raised.

4. Do not allow passengers to remain in

the vehicle.

To be even more certain the vehicle will not move, you should put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire, on the other side, at the opposite end of the vehicle.

When your vehicle has a ﬂat tire, use the following example as a guide to assist you in the placement of wheel blocks.

The following information will tell you next how to use the jack and change a tire.

5-89

Removing the Spare Tire and Tools The equipment needed to change a tire is located in the trunk. 1. Open the trunk. See Trunk on page 2-13 for more

information.

2. Remove the convenience net, if equipped, by

removing the net hook attachments.

3. Lift up the carpet.

4. Turn the center nut on the compact spare tire cover counterclockwise to remove it.

5. Remove the cover. 6. Remove the compact spare tire. See Compact Spare Tire on page 5-99 for more information.

5-90

7. Turn the nut holding the jack counterclockwise and

remove it. Then remove the jack and wrench.

8. The tools you will be using include the jack (A), extension and protector/guide (B) and the wheel wrench (C).

Removing the Flat Tire and Installing the Spare Tire Your vehicle may have aluminum wheels. If so, you will see exposed stainless steel wheel nuts. Use the wheel wrench to loosen all the wheel nuts. Do not remove them yet. Or, your vehicle may have steel wheel covers.

To remove the steel wheel covers and wheel nut caps, loosen the plastic nut caps with the wheel wrench in a counterclockwise direction. If needed, you can ﬁnish loosening them with your ﬁngers. The plastic nut caps will not come off.

5-91

Use the ﬂat end of the wheel wrench and pry along the edge of the cover until it comes off. The edge of the wheel cover could be sharp, so do not try to remove it with your bare hands. Do not drop the cover or lay it face down, as it could become scratched or damaged. Once you have removed the wheel cover, use the following procedure to remove the ﬂat tire and install the spare tire.

1. Turn the wheel wrench once on each wheel nut to loosen them. Do not remove them yet.

5-92

2. Find the jacking location using the diagram. For

jacking at the vehicle’s front location, put the jack lift head (C) about 6 inches (15 cm) from the rear edge of the front wheel opening (B). Line up the jack with the arrow (A) as shown.

{CAUTION:

Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.

{CAUTION:

Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to ﬁt the jack lift head into the proper location before raising the vehicle.

5-93

For jacking at the vehicle’s rear location, put the jack lift head (B) about 9 inches (23 cm) from the front edge of the rear wheel opening (C). Line up the jack with the arrow (A) as shown.

3. Put the compact spare tire near you.

{CAUTION:

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. The jack provided with your vehicle is designed only for changing a ﬂat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. Use the jack provided with your vehicle only for changing a ﬂat tire.

5-94

4. Raise the vehicle by turning the jack handle

clockwise. Raise the vehicle far enough off the ground for the compact spare tire to ﬁt underneath the wheel well of the vehicle.

5. Remove all wheel nuts and take off the ﬂat tire.

{CAUTION:

Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle. In an emergency, you can use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off.

6. Remove any rust or dirt

from the wheel bolts, mounting surfaces and spare wheel.

7. Install the compact spare tire.

{CAUTION:

Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident.

8. Reinstall the wheel nuts with the rounded end of the nuts toward the wheel. Tighten each nut by hand until the wheel is held against the hub.

5-95

{CAUTION:

Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque speciﬁcation. See Capacities and Speciﬁcations on page 5-118 for wheel nut torque speciﬁcation.

Improperly tightened wheel nuts can lead

Notice: to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque speciﬁcation. See Capacities and Speciﬁcations on page 5-118 for the wheel nut torque speciﬁcation.

9. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely.

5-96

10. Tighten the wheel nuts

ﬁrmly in a crisscross sequence as shown.

Storing a Flat or Spare Tire and Tools

Notice: Wheel covers will not ﬁt on your compact spare. If you try to put a wheel cover on the compact spare, you could damage the cover or the spare. Do not try to put the wheel cover on the compact spare tire. It will not ﬁt. Store the wheel cover in the trunk until the ﬂat tire is repaired or replaced.

{CAUTION:

Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.

After the compact spare tire is put on the vehicle, store the ﬂat tire in the trunk. Use the following procedure to secure it in the trunk. When storing a full-size tire, use the extension and protector/guide, located in the foam holder to help avoid wheel surface damage.

5-97

To store a full-size tire, do the following: 1. Install the tools in their original location in the trunk

area and secure.

2. Place the tire in the trunk with the valve stem facing

down, and the protector/guide placed through a wheel bolt hole.

3. Remove the protector and attach the

retainer securely.

4. Place the protector/guide back in the foam holder when putting the compact spare back in the trunk. Store the cover as far forward as possible.

The compact spare tire is for temporary use only. Replace the compact spare tire with a full-size tire as soon as possible. See Compact Spare Tire on page 5-99 for more information. Use the following as a guide for storing the compact spare tire and tools.

A. Retainer B. Cover C. Compact Spare Tire D. Nut E. Jack F. Wheel Wrench G. Extension and

Protective Guide

H. Foam Holder I. Bolt Screw

5-98

Compact Spare Tire Although the compact spare tire was fully inﬂated when the vehicle was new, it can lose air after a time. Check the inﬂation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on the vehicle, stop as soon as possible and make sure the spare tire is correctly inﬂated. The compact spare is made to perform well at speeds up to 65 mph (105 km/h) for distances up to 3,000 miles (5 000 km), so you can ﬁnish your trip and have the full-size tire repaired or replaced at your convenience. Of course, it is best to replace the spare with a full-size tire as soon as possible. The spare tire will last longer and be in good shape in case it is needed again. Notice: When the compact spare is installed, do not take your vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails. That can damage the tire and wheel, and maybe other parts of your vehicle. Do not use the compact spare on other vehicles. And do not mix the compact spare tire or wheel with other wheels or tires. They will not ﬁt. Keep the spare tire and its wheel together. Notice: Tire chains will not ﬁt your compact spare. Using them can damage your vehicle and can damage the chains too. Do not use tire chains on your compact spare.

Appearance Care

Cleaning the Inside of Your Vehicle Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from your upholstery. It is important to keep your upholstery from becoming and remaining heavily soiled. Soils should be removed as quickly as possible. Your vehicle’s interior may experience extremes of heat that could cause stains to set rapidly. Lighter colored interiors may require more frequent cleaning. Use care because newspapers and garments that transfer color to your home furnishings may also transfer color to your vehicle’s interior. When cleaning your vehicle’s interior, only use cleaners speciﬁcally designed for the surfaces being cleaned. Permanent damage may result from using cleaners on surfaces for which they were not intended. Use glass cleaner only on glass. Remove any accidental over-spray from other surfaces immediately. To prevent over-spray, apply cleaner directly to the cleaning cloth.

5-99

If you use abrasive cleaners when cleaning

Notice: glass surfaces on your vehicle, you could scratch the glass and/or cause damage to the integrated radio antenna and the rear window defogger. When cleaning the glass on your vehicle, use only a soft cloth and glass cleaner. Many cleaners contain solvents that may become concentrated in your vehicle’s breathing space. Before using cleaners, read and adhere to all safety instructions on the label. While cleaning your vehicle’s interior, maintain adequate ventilation by opening your vehicle’s doors and windows. Dust may be removed from small buttons and knobs using a small brush with soft bristles. Your GM dealer has a product for cleaning your vehicle’s glass. Should it become necessary, you can also obtain a product from your GM dealer to remove odors from your vehicle’s upholstery.

Do not clean your vehicle using the following cleaners or techniques: (cid:127) Never use a knife or any other sharp object to

remove a soil from any interior surface.

(cid:127) Never use a stiff brush. It can cause damage to

your vehicle’s interior surfaces.

(cid:127) Never apply heavy pressure or rub aggressively

with a cleaning cloth. Use of heavy pressure can damage your interior and does not improve the effectiveness of soil removal.

(cid:127) Use only mild, neutral-pH soaps. Avoid laundry

detergents or dishwashing soaps with degreasers. Using too much soap will leave a residue that leaves streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide.

(cid:127) Do not heavily saturate your upholstery

while cleaning.

(cid:127) Damage to your vehicle’s interior may result from the use of many organic solvents such as naptha, alcohol, etc.

5-100

Fabric/Carpet Cleaning Fabric/Carpet Use a vacuum cleaner often to get rid of dust and loose dirt. Wipe vinyl, leather, plastic, and painted surfaces with a clean, damp cloth. Your GM dealer has cleaners for the cleaning of fabric and carpet. They will clean normal spots and stains very well. If the vehicle has the Ultra Lux® suede fabric, follow the listed procedures except do not use any solvents or dry cleaning products. Here are some cleaning tips: (cid:127) Always read the instructions on the cleaner label. (cid:127) Clean up stains as soon as you can, before

they set.

(cid:127) Carefully scrape off any excess stain. (cid:127) Use a clean cloth or sponge, and change to a

clean area often. A soft brush may be used if stains are stubborn. To avoid forming a ring on fabric after spot cleaning, clean the entire area immediately or it will set.

Most stains can be removed with club soda water. To clean, use the following instructions: 1. For liquids: blot with a clean, soft white cloth. For solids: remove as much as possible and then vacuum or brush.

2. Apply club soda water to a clean, soft white

cloth. Do not over-saturate; the cloth should not drip water.

3. Clean the entire area. Avoid getting the fabric

too wet.

4. Start cleaning from the seams into the stain to

avoid a ring effect.

5. Continue cleaning, using a clean area of the cloth

each time it becomes soiled.

6. When the stain is removed, blot the cleaned area

with another dry clean, soft white cloth.

5-101

(cid:127) Using Cleaner on Fabric 1. First, try the cleaner in an inconspicuous area to

make sure the cleaner does not affect the color of the fabric.

2. For liquids: blot the stain with a clean, soft

white cloth. For solids: remove as much as possible and then vacuum or brush.

3. Spray a small amount of the cleaner onto a

clean, soft white cloth. Do not apply spray directly to the fabric.

4. Start cleaning from the seams into the stain to

avoid a ring effect.

5. Continue cleaning, using a clean area of the cloth

each time it becomes soiled.

6. When the stain is removed, blot the cleaned area

with another dry clean, soft white cloth.

7. If the cleaner leaves a ring effect, follow up with the club soda water instructions given earlier in this section.

Special Fabric Cleaning Problems Stains caused by such things as catsup, coffee, tea, milk, fruit, fruit juice, jelly, cheese, chocolate, vomit, urine, and blood can be removed using the club soda water instructions given earlier in this section. If an odor lingers after cleaning vomit or urine, treat the area with a water and baking soda solution: 1 teaspoon (5 ml) of baking soda to 1 cup (250 ml) of lukewarm water. Let dry. Stains caused by oil and grease can be cleaned with an approved GM cleaner and a clean, white cloth. 1. Carefully scrape off excess stain. 2. Clean with cool water and allow to dry completely. 3. If a stain remains, follow the cleaner instructions

described earlier.

5-102

Leather A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally. Do not use heat to dry. Never use steam to clean leather. Never use spot lifters or spot removers on leather. Many commercial leather cleaners and coatings that are sold to preserve and protect leather may permanently change the appearance and feel of your leather and are not recommended. Do not use silicone or wax-based products, or those containing organic solvents to clean your vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Never use shoe polish on your leather.

Ultra Lux Suede Cleaning Ultra Lux Suede Use a mild solution of lukewarm water and a neutral dish soap on a soft cloth or sponge. For the following stains, follow these instructions:

Coffee, Tea, and Milk: Blot with a clean, soft, white cloth. Then clean with mild soapy water and a clean white cloth.

Cosmetics: Clean with mild soapy water and a clean white cloth.

Jelly, Syrup, and Fruit: Remove most of the solids, then clean with warm tap water and a clean white cloth.

Oil and Grease: Sprinkle baking soda on the spot, brush, then wipe with a clean white cloth.

5-103

Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces. Many commercial cleaners and coatings that are sold to preserve and protect soft plastic surfaces may permanently change the appearance and feel of your interior and are not recommended. Do not use silicone or wax-based products, or those containing organic

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2006 Pontiac Grand PRIX Owners Manual