1995 Pontiac Grand PRIX Owners Manual

1. Remove the pins from the cover above the fog

lamps.

5. 6. 7.

8.

3. 4.

Pull out the bulb socket. Lift the plastic locking tab on the electrical connector and pull the connector from the bulb socket. Snap the electrical connector into a new bulb socket. Install the screws. Replace the socket into the housing and turn clockwise until it snaps in place. Replace the cover and pins.

6-4 1

Center High-Mounted Stoplamp (2-Door Models)

3. Pull out the bulb.

4. Push in a new bulb. 5. Clip the bulb carrier back into place. 6. Replace the cover and screws.

1. Remove two screws and the cover. 2. Unclip the bulb carrier and pull it out.

To remove the stoplamp lens to clean the window, remove the two nuts on either side of the housing.

6-42

Center High-Mounted Stoplamp (4-hor Models)

3. Lift the tabs at the top

and bottom of the socket and pull it from the housing.

4. Pull out the bulb. 5. Push in a new bulb. 6. Push the socket back into the housing. Make sure the

tabs snap in place.

7. Replace the cover and screws.

1. Remove the two screws from the cover. 2. PulI down the cover.

6-43

2.

3. 4. 5. 6.

7.

If the socket has a tab, squeeze it. Turn the socket counterclockwise. Pull out the socket. Pull the bulb aut of the socket. Push in a new bulb. Replace the socket into the housing and turn clockwise. Reposition the carpet and install the plastic retainers.

Rear Lamp Bar

4. T m the socket

counterclockwise until it pops loose from the housing.

1. Remove the plastic retainers and pull the carpet

away from the rear of the trunk.

2. Remove the wing nuts. 3. Pull the housing away from the body of the vehicle.

5. Pull out the socket. 6. Full the bulb out of the socket. 7 . Push in a new .bulb. 8. Replace the socket into the housing and turn

clockwise.

9. Replace the housing to the body of the vehicle, 10. Install the wing nuts. 11. Reposition the carpet and install the plastic

retainers.

6-45

Windshield Wiper Blade

Tires

2. Lift the release clip with a screwdriver and pull the

blade off the wiper arrn.

3. Push the new wiper blade securely onto the wiper

arm.

6-46

Mation - Tire Pressure The Tire-Loading Information label which is on the rear edge of the driver’s door if you have a two-door or on the inside of the trunk lid if you have a four-door shows the correct inflation pressures for your tires, when they’re cold. “Cold” means your vehicle has been sitting for at least three hours or driven no more than a mile.

NOTICE: Don’t let anyone tell you that underinflation or If your tires overinflation is all right. It’s not. don’t have enough air (underinflation) you can get:

Too much flexing Too much heat Tire overloading Bad wear Bad handling

0 Bad fuel economy.

NOTICE: (Continued)

6-47

Tire Inspection and Rotation Tires should be inspected every 6,000 to 8,000 miles (10 000 to 13 000 km) for any signs of unusual wear. If unusual wear is present, rotate your tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See “When It’s Time for New Tires” and “Wheel Replacement” later in this section for more information. The purpose of regularrotation is to achieve more uniform wear for all tires on the vehicle. The first rotation is the most important. See “Scheduled Maintenance Services” in the Index for scheduled rotation intervals. I n

NOTICE: (Continued) If your tires have too much air (overinflation), you can get: 0 Unusual wear Bad handling Rough ride

0 Needless damage from road hazards.

P en to Check Check your tires once a month or more. ,Don’t forget your compact spare tire. It should be at 60 psi (420 kPa). How to Check Use a good quality pocket-type gage to check tire pressure. Simply looking at the tires will not tell you the pressure, especially if you have radial tires -- which may look properly inflated even if they’re underinflated. If your tires have valve caps, be sure to put them back on. They help prevent leaks by keeping out dirt and moisture.

6-48

When rotating your tires, always use the correct rotation pattern shown here. Don’t include the compact spare tire in your tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire-Loading Information label. Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” in the Index.

When It’s Time for New Tires

One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining.

.. .

You need a new tire if

You can see the indicators at three or more places around the tire. You can see cord or fabric showing through the tire’s rubber. The tread or sidewall is cracked, cut or snagged deep enough to show cord or fabric. The tire has a bump, bulge or split.

0 The tire has a puncture, cut, or other damage that

can’t be repaired well because of the size or location of the damage.

6-49

Buying New Tires To find out what kind and size of tires you need, look at the Tire-Loading Information label. The tires installed on your vehicle when it was new had a Tire Performance Criteria Specification (TPC Spec) number on each tire’s sidewall. When you get new tires, get ones with that same TPC Spec number. That way, your vehicle will continue to have tires that are designed to give proper endurance, handling, speed rating, traction, ride and other things during normal service on your vehicle. If your tires have an all-season tread design, the TPC number will be followed by an “MS” (for mud and snow). If you ever replace your tires with those not having TPC Spec number, make sure they are the same size, load range, speed rating and construction type (bias, bias-belted or radial) as your original tires.

6-50

Uniform Tire Quality Grading The following information relates to the system developed by the United States National Highway Traffic Safety Administration which grades tires by treadwear, traction and temperature performance. (This applies only to vehicles sold in the United States.)

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate. Traction - A, B, C The traction grades, from highest to lowest are: A, B, and C. They represent the tire’s ability to stop on wet pavement as measured under controlled conltions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on braking (straight-ahead) traction tests and does not include cornering (turning) traction.

Temperature - A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. These grades are molded on the sidewalls of passenger car tires.

While the tires available as standard or optional equipment on General Motors vehicles may vary with respect to these grades, all such tires meet General Motors performance standards and have been approved for use on General Motors vehicles. All passenger type (P Metric) tires must conform to Federal safety requirements in addition to these grades. Wheel Alignment and Tire Balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. In most cases, you will not need to have your wheels aligned again. However, if you notice unusual tire wear or your vehicle pulling one way or the other, the alignment may need to be reset. If you notice your vehicle vibrating when driving on a smooth road, your wheels may need to be rebalanced.

Wheel Replacement Replace any wheel thatsis bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it (except some aluminum wheels, which can sometimes be repaired). See your Pontiac dealer if any of these conditions exist. Your dealer will know the kind of wheel you need. Each new wheel should have the same load carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts, or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts, and wheel nuts for your Pontiac model.

6-52

Used Replacement Wheels

NOTICE: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer/odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis.

6-53

! i Tire Chains

NOTICE: If your Pontiac has P215/60R16 or P225/60R16 size tires, don’t use tire chains; they can damage your vehicle. If you have other tires, use tire chains only where legal and only when you must. Use only SAE Class “S” type chains that are the proper size for your tires. Install them on the front tires and tighten them as tightly as possible with the ends securely fastened. Drive slowly and follow the chain manufacturer’s instructions. If you can hear the chains contacting your vehicle, stop and retighten them. If the contact continues, slow down until it stops. Driving too fast or spinning the wheels with chains on will damage your vehicle.

)us, Some

Appearance Care Remember, cleaning products can be haza are toxic. Others can burst into flame if you strike a match or get them on a hot part of the vehicle. Some are dangerous if you breathe their fumes in a closed space. When you use anything from a container to clean your Pontiac, be sure to follow the manufacturer’s warnings and instructions. And always open your doors or windows when you’re cleaning the inside. Never use these to clean your vehicle:

Gasoline Benzene Naphtha

0 Carbon Tetrachloride 0 Acetone 0 Paint Thinner 0 Turpentine 0 Lacquer Thinner 0 Nail Polish Remover They can all be hazardous -- some more than others -- and they can all damage your vehicle, too.

Don’t use any of these unless this manual says you can. In many uses, these will damage your vehicle:

Alcohol Laundry Soap Bleach

0 Reducing Agents Cleaning the Inside of Your Pontiac Use a vacuum cleaner often to get rid of dust and loose dirt. Wipe vinyl or leather with a clean, damp cloth. Your Pontiac dealer has two GM cleaners, a solvent-type spot lifter and a foam-type powdered cleaner. They will clean normal spots and stains very well. Do not use them on vinyl or leather. Here are some cleaning tips: 0 Always read the instructions on the cleaner label.

Clean up stains as soon as you can -- before they set. Use a clean cloth or sponge, and change to a clean area often. A soft brush may be used if stains are stubborn.

0 Use solvent-type cleaners in a well-ventilated area

only. If you use them, don’t saturate the stain.ed area. If a ring forms after spot cleaning, clean the entire area immediately or it will set.

Using Foam-mpe Cleaner on Fabric

Vacuum and brush the area to remove any loose dirt. Always clean a whole trim panel or section. Mask surrounding trim along stitch or welt lines. Mix Multi-Purpose Powdered Cleaner following the directions on the container label. Use suds only and apply with a clean sponge. Don’t saturate the material. Don’t rub it roughly. As soon as you’ve cleaned the section, use a sponge to remove the suds. Rinse the section with a clean, wet sponge. Wipe off what’s left with a slightly damp paper towel or cloth. Then dry it immediately with a blow dryer or a heat lamp.

NOTICE: Be careful. A blow dryer or a heat lamp may scorch the fabric.

0 Wipe with a clean cloth.

6-55

Using Solvent-Type Cleaner on Fabric First, see if you have to use solvent-type cleaner at all. Some spots and stains will clean off better with just water and~mild soap. If you need to use a solvent: 0 Gently scrape excess soil from the trim material with a clean, dull knife or scraper. Use very little cleaner, light pressure and clean cloths (preferably cheesecloth). Cleaning should start at the outside of the stain, “feathering” toward the center. Keep changing to a clean section of the cloth. When you clean a stain from fabric, immediately dry the area with a blow dryer to help prevent a cleaning ring. (See the previous NOTICE.)

Special Cleaning Problems Greasy or Oily Stains Stains caused by grease, oil, butter, margarine, shoe polish, coffee with cream, chewing gum, cosmetic creams, vegetable oils, wax crayon, tar and asphalt can be removed as follows: 0 Carefully scrape off excess stain.

Follow the solvent-type instructions described earlier. Shoe polish, wax crayon, tar and asphalt will stain if left on a vehicle seat fabric. They should be removed as soon as possible. Be careful, because the cleaner will dissolve them and may cause them to spread.

Non-Greasy Stains Stains caused by catsup, coffee (black), egg, fruit, fruit juice, milk, soft drinks, wine, vomit, urine and blood can be removed as follows: 0 Carefully scrape off excess stain, then sponge the

soiled area with cool water. If a stain remains, follow the foam-type instructions described earlier.

6-56

0 If an odor lingers after cleaning vomit or urine, treat the area with a waterhaking soda solution: 1 teaspoon (5 ml) of baking soda to 1 cup (250 ml) of lukewarm water.

0 If needed, clean lightly with solvent-type cleaner. Combination Stains Stains caused by candy, ice cream, mayonnaise, chili sauce and unknown stains can be removed as follows: Carefully scrape off excess stain, then clean with cool water and allow to dry. If a stain remains, clean it with solvent-type cleaner.

Cleaning Vinyl Use warm water and a clean cloth. 0 Rub with a clean, damp cloth to remove dirt. You

may have to do it more than once. Things like tar, asphalt and shoe polish will stain if you don’t get them off quickly. Use a clean cloth and a GM vinylheather cleaner.

ueaning Leather Use a soft cloth with lukewarm water and a mild soap or saddle soap.

For stubborn stains, use a GM vinyl/leather cleaner. 0 Never use oils, varnishes, solvent-based or abrasive cleaners, furniture polish or shoe polish on leather. Soiled leather should be cleaned immediately. If dirt is allowed to work into finish, it can harm the leather.

Cleaning the Top of the Instrument Panel Use only mild soap and water to clean the top surfaces of the instrument panel. Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions.

6-57

Care of Safety Belts Keep belts clean and dry.

Glass Glass should be cleaned often. GM Glass Cleaner (GM Part No. 1050427) or a liquid household glass cleaner will remove normal tobacco smoke and dust films. Don’t use abrasive cleaners on glass, because they may cause scratches. Avoid placing decals on the inside rear window, since they may have to be scraped off later. If abrasive cleaners are used on the inside of the rear window, an electric defogger element may be damaged. Any temporary license should not be attached across the defogger grid.

6-58

Cleaning the Outside of the Windshield and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with GM Windshield Cleaner, Bon-Ami Powder@ (GM Part No. 1050011). The windshield is clean if beads do not form when you rinse it with water. Clean the blade by wiping vigorously with a cloth soaked in full strength windshield washer solvent. Then rinse the blade with water. Wiper blades should be checked on a regular basis and replaced when worn. Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth at least every six months. During very cold, damp weather more frequent application may be required. (See “Recommended Fluids and Lubricants” in the Index.)

Cleaning the Outside of Your Pontiac The paint finish on your vehicle provides beauty, depth “ color, gloss retention and durability. Washing Your VehicIe The best way to preserve your vehicle’s finish is to keep it clean by washing it often with lukewarm or cold water. Don’t wash your vehicle in the direct rays of the sun. Don’t use strong soaps or chemical detergents. Use liquid hand, dish or car washing (mild detergent) soaps. Don’t use cleaning agents that are petroleum based, or that contain acid or abrasives. All cleaning agents should be flushed promptly and not allowed to dry on the surface, or they could stain. Dry the finish with a soft, clean chamois or a 100% cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter your vehicle. Finish Care Occasional waxing or rnild polishing of your Pontiac by hand may be necessary to remove residue from the paint finish. You can get GM approved cleaning products from your dealer. (See “Appearance Care and Materials” in the Index.)

Your Pontiac has a “basecoatklearcoat” paint finish. The clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoatklearcoat paint finish.

I NOTICE:

Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may dull the finish or leave swirl marks.

Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc. can damage your vehicle’s finish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter. Exterior painted surfaces are subject to aging, weather and chemical fallout that can take their toll over a period of years. You can help to keep the paint finish looking new by keeping your Pontiac garaged or covered whenever possible.

6-59

, Aluminum Wheels (If So Equipped)

Your aluminum wheels have a protective coating similar to the painted surface of your vehicle. Don’t use strong soaps, chemicals, chrome polish, abrasive cleaners or abrasive cleaning brushes on them because you could damage this coating. After rinsing thoroughly, a wax may be applied.

NOTICE: If you have aluminum wheels, don’t use an automatic car wash that has hard silicon carbide cleaning brushes. These brushes can take the protective coating off your aluminum wheels.

Tires To clean your tires, use a stiff brush with a tire cleaner. When applying a tire dressing always take care to wipe off any overspray or splash from painted surfaces. Petroleum-based products may damage the paint finish. Sheet Metal Damage If your vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to the parts repaired or replaced to restore corrosion protection. Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into a major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer or other service outlets. Larger areas of finish damage can be corrected in your dealer’s body and paint shop.

Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, accelerated corrosion (rust) can occur on the underbody parts such as %el lines, frame, floor pan, and exhaust system even though they have corrosion protection. At least every spring, flush these materials from the underbody with plain water. Clean any areas where mud will repair, and other debris can collect. Dirt packed in closed areas new vehicles damaged by of the frame should be loosened before being flushed. Your dealer or an underbody vehicle washing system can do this for you. Fiberglass Springs

Chemical Paint Spotting Some weather and atmospheric conditions CZUI create a chemical fallout, Airborne pollutants can fall upon and attack painted surfaces on your vehicle. This damage can take two forms: blotchy, ringlet-shaped discolorations, and small irregular dark spots etched into the paint surface. Although no defect in the paint job causes this, Pontiac

at no charge to the owner, the surfaces of

this fallout condition within 12 months or 12,000 miles (20 000 km) of purchase, whichever comes first.

1 NOTICE:

Don’t use corrosive or acidic cleaning agents, engine degreasers, aluminum cleaning agents or other harsh solvents to clean fiberglass springs; they’ll damage the springs.

6-61

Vehicle Identification Number (VIN)

UXSMJ72675 4 - 1995 \ PLANT

Ictn) ASSEMBLY

MODEL YEAR

--

This is the legal identifier for your Pontiac. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certification and Service Parts labels and the certificates of title and registration. Engine Identification The eighth character in your VIN is the engine code. This code will help you identify your engine, specifications, and replacement parts.

Service Parts Identification Label You’ll find this label on your spare tire cover. It’s very helphl if you ever need to order parts. On this label is:

yoLlrvIN, the model designation, 0 paint information, and

a list of all production options and special equipment.

Be sure that this label is not removed from the vehicle. Add-on Electrical Equipment

I NOTICE:

Don’t add anything electrical to your Pontiac unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.

Your vehicle has an air bag system. Before attempting to add anything electrical to your Pontiac, see “Servicing Your Air Bag-Equipped Pontiac” in the Index.

6-63

Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers, and fusible thermal links in the wiring itself. This greatly reduces the chance of fires caused by electrical problems.

Some fuses are in a fuse block on the passenger side of the instrument panel. Pull off the cover labeled FUSES to expose the fuses.

Additional fuses are in the underhood electrical centers on the right and left sides of the engine compartment. Look at the silver-colored band inside the fuse. If the band is broken or melted, replace the fuse. Be sure you replace a bad fuse with a new one of the identical size and rating.

6-64

Instrument Panel Fuse Block

Circuit Description Breaker

Power Windows Power Seats

Fuse

10

11 12 14

15

16

19

21

Description CIGAR LIGHTER -- Instrument Panel Cigar Lighter HAZARD FLASHER POWER ACCESSORY #2 -- SUIKOO~ Control Unit LOCK CONTROL -- Door Lock Relay YP ELECTRONICS BATTERY FEED -- Chime Module, Electronic Brake Control Module (EBCM), Theft Deterrent Module, Radio, Radio Amplifier, Trip Computer STARTER MOTOR ANTI-THEFT -- Theft Deterrent Module W A C BLOWER MOTOR -- Blower Motor Relay W A C #1-- Air Temperature Valve Motor, Trip Computer, Daytime Running Lamps Module (with D m ) , W A C Control Assembly, Multifunction Lever Cruise Control Switch REAR DEFOG -- W A C Control Assembly Rear Window Defogger Switch POWER ACCESSORY #1 -- Antenna Relay, Power Mirror Switch, Door Lock Switches, Door Handle Switches AIR BAG -- Sensing and Diagnostic Module @DM)

Fuse 23 24

28

29 30 32 33

37 38

39

Description STOPLAMPS -- TCCBrake Switch HVAC #2 -- HVAC Control Assembly, Solenoid Box CTSY LAMPS -- Vanity Mirrors, VP Courtesy Lamps, I/P Compartment Lamp, Trunk Courtesy Lamp, Header Courtesy and Reading Lamp, US Lighted Rearview Mirror, Dome and Reading Lamp, Quarter Courtesy Lamps WIPER -- Wiper Switch TURN SIGNAL -- Turn Signal Flasher POWER LOCKS -- Door Lock Relay A B S -- Electronic Brake Control Module (EBCM), A B S Relay AUXILIARY POWER RADIO -- Radio, Steering Wheel Radio Switches I/P ELECTRONICS IGNITION FEED -- Headlamp Switch, Cruise Control Cut-Out Switch, Sensing and Diagnostic Module (SDM), TCCBrake Switch, Instrument Cluster, Chime Module, Second Gear Start Switch, Head-Up Display (HUD) Switch, Daytime Running Lamps Module (with D m )

6-65

- .

er

\ 1 -

13

Fuse WCMPT REL

ECM BAT

TCC

ENG EMIS

F/INJN

Description Remote Trunk Release, Backup Lamps Powertrain Control Module (PCM), Fuel Pump Switch, Fuel Pump Relay, Fan Cont #1 Relay Automatic Transaxle, Transaxle Range Switch (VIN M only) Fan Cont #2 Relay, N C CMPR Relay (VIN M only) Fuel Injectors

Underhood Electrical Center -- P

Side

on0 TCC on0

ENGEMIS

F/INJN ECM

IGN ELEK IGN

6-66

Fuse ECM IGN

ELEK IGN

10 11 12

13

Description Powertrain Control Module (PCM), Mass Air Flow WAF) Sensor (VIN X only), EGR, CCP, Oxygen Sensor, Vac. Can. Switch Electronic Ignition (EI) Control Module YP Fuse Block FAN CON" #1 Relay Passenger Side Underhood Electrical Center and UP Fuse Blocks: Fuses 5, 149 23 and 32 FAN CONT #2 Relay and I/P Fuse Block Fuse 16, Power Seat Circuit Breaker '2)"

Relay 14 15 16

17

18

Description FUEL PUMP AfC CMPR FAN CONT #2 -- Secondary Cooling Fan (Passenger Side) FAN CON" #1-- P1-ima.r~ Coohg Fan (Driver Side) Ignition Switch Relay

6-67

Underhood Electrical Center -- Driver Side

on0 on0

FOG LPS PARKLPS HORN

VAR PIS

II

’ I

Description Fuse FOG LPS Fog Lamps PARK LPS Headlamp Switch HORN VAR PIS

Horn Relay, Underhood Lamp EVO

6-68

Fuse 10

11

12

13 Relay 14 15 16

Description IGN SW2 -- I/P Fuse Block PWR WDO and Circuit Breaker “D’; Passenger Side Underhood Electrical Center: TCC and ENG EMIS Fuses IGN SWl -- I/P Fuse Block: Radio, Wiper, WAC, ABS and Turn Signal Fuses; Passenger Side Underhood Electrical Center: F/IJN, ECM IGN and ELEK IGN Fuses HD LPS -- 30 Amp Circuit Breaker to Headlamp Switch A B S -- ABS Relay Description ABS -- Anti-lac- Brake Svstem FOG LPS HORN

Power Windows and Other Power Options Circuit breakers in the fuse panel protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is fixed.

Headlamp Wiring The headlamp wiring is protected by a circuit breaker in the underhood electrical center. An electrical overload will cause the lamps to go on and off, or in some cases to remain off. If this happens, have your headlamp system checked right away. Windshield Wipers The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem, have it fixed.

6-69

Bulb- Number 3057

Replacement Bulbs Exterior.Lamps Back-up .................................. Center High-Mounted Stop Roof-Mounted ........................... Shelf-Mounted ............................ Fag ............................ 2-Door Models 4-Door Models ............................ Front Parking/Turn Signal

891T2 2355

H3 881

........................ ............................

2-Door Models 3057NA 4-Door Models 889 Headlamp, High Beam 2-Door Models ...................... H4352 (U) 4-Door Models ........................... 9005 Headlamp. Low Beam 2-Door Models ...................... H435 1 (L) ........................... 4-DaorModels 9006 License Plate ................................ 194 LightBar. Front ............................ 3057 Light Bar Panel. Rear ......................... 194 Sidemaker. Front 2-Door Models ............................. 24 .......................... 24NA 4-Daor Models Sidemmker. Rear ............................. 194 Stop/'I'aW'hrn Signal ........................ 3057

6-70

~-

Bulb Number Interior Lamps Ashtray .................................... 194 Center Instrument Cluster ............ 161. 194. 194R Courtesy Dome .................................... 561 Door ............................. 562or212-2 Instrument Panel ........................... 194 Windshield Header ................. 562 or 212-2 GloveBox .................................. 194 ...... T- 1 1 . 5 Heater and Air Conditioning Control High-Beam Indicator ......................... 161 Instrument Cluster Indicator ................. PC 161 Luggage Compartment ........................ 920 Reading Dome ..................................... 24 Inside Rearview Mirror ...................... 192 RearSeat .................................. 906 Windshield Header .................. 562 or 212-2 Turn Signal Indicator ...................... PC161 Visor Vanity 74

.................................

.O. T-

Capacities and Specifications Automatic Transaxle . . . . . . . 4 quarts (3.8 L) Pan Removal and Replacement After Complete Overhaul ............ 7 quarts (6.7 L) When drainingheplacing converter or auxiliary cooleq more fluid may be needed. Automatic Tkansaxle with Overdrive

. . . . . . . 7 quarts (6.7 L) Pan Removal and Replacement After Complete Overhaul . . . . . . . . . . . 10 quarts (9.5 L) When drainingheplacing converter or auxiliary cooler, more fluid may be needed.

Engine Specifications Type .......................................... Displacement ................................... Compression Ratio ............................... Firingorder .................................... .......................... Thermostat Temperature ValveArrangement ..............................

Cooling System Including Reservoir 3.1L (Code M) . . . . . . . . . . . . . . . . 11.6 quarts (10.93 L) 3.4L (Code X) ................. 12.3 quarts (1 1.65 L) ............................

Refrigerant (R-l34a), Air Conditioning"

2.0 pounds (0.91 kg)

Engine Crankcase

3.1L (Code M) . . . . . . . . . . . . . . . . . . . 4 quarts (3.8 L)* 3.4L (Code X) .................... 5 quarts (4.7 L)* *Add 1/2 quurt (0.5 L) more when filter is changed. Fuel Tank ..................... 16.5 gallons (62.0 L) *See "Air Conditioning Refrigerants '' later in this section.

3.1L (Code M)

191 CID (3.1L)

V6

9.5: 1

1-2-3-4-5-6 195°F (91 "C)

In-Head

3.4L (Code X)

V6

207 CID (3.4L)

9.25: 1

1-2-3-4-5-6 195°F (91°C)

In-Head

6-71

Normal Maintenance Replacement Parts Air Cleaner Filter All Engines ............................. A1208C Battery

525 CCA 690 CCA

3.1L (Code M) ......................... 3.4L (Code M) ......................... Engine Oil Filter 3.1L (Code M) ............................. 3.4L (Code X) .............................. PCV Valve .......................... CV892C 3.1L (Code M) 3.4L (Code X) ........................... CV895C

PF47 PF5 1

Air Conditioning Refrigerants Not all air conditioning refrigerants are the same. If the air conditioning system in your vehicle needs refrigerant, be sure the proper refrigerant is used. If you’re not sure, ask your Pontiac dealer. For additional information, see your “Warranty and Owner1 Assistance Information” booklet.

Radiator Cap All Engines ............................... Spark Plugs 3.1L (Code M) .......................

RC27

3.4L (Code X) .........................

oR44LTSM6 Gap: 0.060” (1 5 2 mm) oR42LTSM Gap: 0.045” (1.14 mm)

NOTES

6-73

NOTES

6-74

Section 7 Maintenance Schedule

IMPORTANT: KEEP ENGINE OIL AT THE PROPER

LEVEL AND CHANGE A I

RECOMMENDED

This section covers the maintenance required for your Pontiac. Your vehicle needs these services to retain its safety, dependability and emission control performance.

protection I

GM

Introduction Your Vehicle and the Environment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment. All recommended maintenance procedures are important. Improper vehicle maintenance or the removal of important components can significantly affect the quality of the air we breathe. Improper fluid levels or even the wrong tire inflation can increase the level of emissions from your vehicle. To help protect our environment, and to help keep your vehicle in good condition, please maintain your vehicle properly.

Have you purclzased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Pontiac dealer f o r details.

7-1

How This Section is Organized The remainder of this section is divided into five parts: “Part A: Scheduled Maintenance Services” shows what to have done and how often. Some of these services can be complex, so unless you are technically qualified and have the necessary equipment, you should let your dealer’s service department or another qualified service center do these jobs.

If you are skilled enough to do some work on your vehicle, you will probably want to get the service information GM publishes. You will find a list of publications and how to get them in this manual. See “Service Publications” in the Index. 7-2

“Part B: Owner Checks and Services” tells you what should be checked whenever you stop for fuel. It also explains what you can easily do to help keep your vehicle in good condition. “Part C : Periodic Maintenance Inspections” explains important inspections that your Pontiac dealer’s service department or another qualified service center should perform. “Part D: Recommended Fluids and Lubricants” lists some products GM recommends to help keep your vehicle properly maintained. These products, or their equivalents, should be used whether you do the work yourself or have it done. “Part E: Maintenance Record” provides a place for you to record the maintenance performed on your vehicle. Whenever any maintenance is performed, be sure to write it down in this part. This will help you determine when your next maintenance should be done. In addition, it is a good idea to keep your maintenance receipts. They may be needed to qualify your vehicle for warranty repairs.

~

~11 Motors want to help you keep your

Part A: Scheduled Maintenance Services Using Your Maintenance Schedule we at Gen vehicle in good workmg condition. But we don’t know exactly how you’ll drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather. You may use your vehicle in making deliveries. Or you may drive it to work, to do errands or in many other ways. Because of all the different ways people use their GM vehicles, maintenance needs vary. You may even need more frequent checks and replacements than you’ll find in the schedules in this section. So please read tlvs section and note how you drive. If you have any questions on how to keep your vehicle in good condition, see your Pontiac dealer. This part tells you the maintenance services you should have done and when you should schedule them. If you go to your dealer for your service needs, you’ll know that GM-trained and supported service people will perform the work using genuine GM parts.

The proper fluids and lubricants to use are listed in Part D. Make sure whoever services your vehicle uses these. All parts should be replaced and all necessary repairs done before you or anyone eke drives the vehicle. These schedules are for vehicles that:

cany passengers and cargo within recommended limits. You will find these limits on your vehicle’s Tire-Loading Information label. See “Loading Your Vehicle” in the Index. are driven on reasonable road surfaces within legal driving limits. use the recommended unleaded fuel. See “Fuel” in the Index.

Selecting the Right Schedule First you’ll need to decide which of the two schedules is right for your vehicle. Here’s how to decide which schedule to follow:

7-3

Maintenance Schedule

Schedule I Definition Follow Maintenance Schedule I if any one of these is true for your vehicle: 0 Most trips are less than 5 to 10 miles (8 to 16 km).

This is particularly important when outside temperatures are below freezing.

0 Most trips include extensive idling (such as frequent

driving in stop-and-go traffic).

0 Most trips are through dusty areas. 0 You frequently tow a trailer or use a carrier on top of

your vehicle.

Schedule I should also be followed if the vehicle is used for delivery service, police, taxi, or other commercial application.

7-4

I Intervals

=Schedule Every 3,000 Miles (5 000 km) or 3 Months, Whichever Occurs First Every 6,000 Miles (10 000 km) o r 6 months, Whichever Occurs First

Engine Oil and Filter Change

Chassis Lubrication

At 6,000 Miles (10 000 km) - Then Every 12,000

Miles (25 000 km)

Tire Rotation

Air Cleaner Filter Inspection, if driving in dusty conditions

Every 15,000 Miles (25 000 km) Every 30,000 Miles (50 000 km) Air Cleaner Filter Replacement Spark Plug Replacement Spark Plug Wire Inspection Fuel Tank, Cap and Lines Inspection Engine Accessory Drive Belt Inspection (or every

24 months, whichever occurs first)

Cooling System Service (or every 24 months,

whichever occurs first)

Automatic Transaxle Service (severe conditions only)

Every 50,000 Miles (83 000 km) At 60,000 Miles (100 000 km) - Then Every 15,000 Miles (25 000 km)

Camshaft Timing Belt Inspection (3.4L Code X engine only)

Maintenance Schedule

Follow Schedule IT only if none of the conditions from Schedule I is true.

Schedule I1 Intervals Every 7,500 Miles (12 500 km)

Engine Oil and Filter Change (or every 12 months,

whichever occurs first)

Chassis Lubrication (or every 12 months, whichever

occurs first)

At 7,500 Miles (12 500 km) - Then Every 15,000 Miles (25 000 km)

Tire Rotation

Every 30,000 Miles (50 000 km)

Engine Accessory Drive Belt Inspection (or every

24 months, whichever occurs first)

Cooling System Service (or every 24 months,

whichever occurs first)

Spark Plug Replacement Spark Plug Wire Inspection Air Cleaner Filter Replacement Fuel Tank, Cap and Lines Inspection

Every 50,000 Miles (83 000 knl) Automatic Transaxle Service (severe conditions only) At 60,000 Miles (100 000 km) - Then Every 15,000 Miles (25 000 km) Camshaft Timing Belt Inspection (3.4L Code X

engine only)

7-5

I ,Maintenance Schedule I

The services shown in this schedule up to 100,008 miles (166 000 km) should be performed after 100,000 miles (166 000 km) at the same intervals. Footnotes The U.S. Environmental Protection Agency or the

California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of vehicle useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded.

3,000 Miles (5 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

DATE

ACTUAL MILEAGE

SERVICED BY:

I Maintenance Schedule I 6,000 Miles (10 000 km)

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first). CI Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional information.

€ ACTUAL MILEAGE SERVICED BY:

9,000 Miles (15 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Sewice.

DATE

ACTUAL MILEAGE

SERVICED BY:

-.- -

._ =

- . x.-..

7-7

I Maintenance Schedule I 12,000 Miles (20 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

[7 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).

15,000 Miles (25 000 km) 0 Change engine oil and filter (or even

3 months, whichever occurs first). An Emission Control Service.

0 Inspect air cleaner filter if you are driving

in dusty conditions. Replace filter if necessary. An Emission Control Service.

DATE ACTUAL MILEAGE SERVICED

BY:

DATE ACTUAL MILEAGE

SERVICED BY:

7-8

I Maintenance Schedule I 18,000 Miles (30 000 km) c] Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Sewice.

0 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first). 0 Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional information.

21,000 Miles (35 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Sewice.

DATE

ACTUAL MILEAGE

SERVICED BY:

DATE SERVICED

ACTUAL MILEAGE

BY:

7-9

-~

24,000 Miles (40 000 km)

Change engine oil and filter (or every 3 months, whichever occurs, first). An Emission Control Service.

17 Lubricate the shift linkage, parking brake cable guides, underbody cantact points and linkage (or every 6 months, whichever occurs first).

0 Change engine oil and filter (or" every

3 months, whichever occurs first). An Emission Control Service.

Maintenance Schedule I 30,000 Miles (50 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first). 17 Inspect engine accessory drive belt (or

every 24 months, whichever occurs first). An Emission Control Service. 0 Drain, flush and refill cooling system (or every 24 months, whichever occurs first). See “Engine Coolant’’ in the Index for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. An Emission Control Service.

0 Replace spark plugs. An Emission 0 Inspect spark plug wires. An Emission 0 Replace air cleaner filter. Replace filter

Control Service. Control Sewice. 3-

more often under dusty conditions. An Emission Control Sewice.

0 Inspect fuel tank, cap and lines for damage

or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. An Emission Control Service. 3-

0 Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional information.

DATE ACTUAL MILEAGE SERVICED

BY:

7-11

D&TE.

ACTUAL MILXAGE

I Maintenance Schedule I 39,000 Miles (65 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

DATE SERVICED

ACTUAL MILEAGE

BY:

42,000 Miles (70 000 km) 17 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first). Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information.

I DATE

ACTUAL

MILEAGE

SERVICED

BY:

7-13

1

I Maintenance Schedule I 50,000 Miles (83 000 km) 0 Change automatic transaxle fluid and filter if the vehicle is mainly driven under one or more of these conditions: - In heavy city traffic where the outside

temperature regularly reaches 90 O F (32T) or higher.

- In hilly or mountainous terrain. - When doing frequent trailer towing. - Uses such as found in taxi, police or

delivery service.

Ifyou do not use your vehicle under any of these conditions, the fluid andjcilter do not require changing.

I DATE

I ACTUAL MILEAGE

ISERVICED

BXI

51,000 Miles (85 000 km) 17 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Co.ygrQJ Service.

DATE

ACTUAL MILEAGE

SERVICED BY:

7-15

57,000 Miles (95 000 km)

Change engine ail and filter (or every 3 months, whichever o,ccurs first). An Emission ContmE Sewice.

DATE .--

ACTUAL MILEAGE SERVICD BY:

Maintenance Schedule. 1 60,000 Miles (100 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).

0 Inspect engine accessory drive belt (or

every 24 months, whichever occurs first). An Emission Control Service. Inspect camshaft timing belt. An Emission Control Service. 0 Drain, flush and refill cooling system (or every 24 months, whichever occurs first). See “Engine Coolant” in the Index for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. An Emission Control Service.

Replace spark plugs. An Emission Control Service.

0 Inspect spark plug wires. An Emission Control 0 Replace air cleaner filter. Replace filter

Service.

more often under dusty conditions. An Emission Control Sewice.

CI Inspect fuel tank, cap and lines for damage

or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. An Emission Control Service.

7-17

I Maintenance Schedule I 1 63,000 Miles (105 000 km)

’

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Sewice.

DATE SERVICED

ACTUAL MILEAGE

BY:

7-18

66,000 Miles (110 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service. Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first). 17 Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional information.

DATE

ACTUAL MILEAGE I

SERVICED BY:

I Maintenance Schedule I 69,000 Miles (115 000 km) Cl Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

72,000 Miles (120 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service. Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).

DATE

ACTUAJ' MILEAGE

SERVICED BY:

I DATE

ACTUAL

MILEAGE

SERVICED

BY:

7-19

78,000 Miles (130 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake

cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first). 0 Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional information.

I Maintenance Schedule I 75,000 Miles (125 000 km) Cl Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

0 Inspect air cleaner filter if you are driving

in dusty conditions. Replace filter if necessary. An Emission Control Service. Inspect camshaft timing belt. An Emission Control Service.

DATE

ACTUAL MILEAGE

SERVICED BY:

7-20

I Maintenance Schedule I 81,000 Miles (135 000 km) 0 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

84,000 Miles (140 000 km)

Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first).

DATE

ACTUAL MILEAGE

SERVICED BY:

DATE

ACTUAL MILEAGE

SERVICED BY:

- 7-21

1 Maintenance Schedule I 87,000 Miles (145 000 km) 17 Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

90,000 Miles (150 000 km) Cl Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake

cable guides, underbody contact points and linkage (or every 6 months, whichever occurs first). 0 Inspect engine accessory drive belt (or

every 24 months, whichever occurs first). An Emission Control Service. 0 Inspect camshaft timing belt. An Emission

DATE

ACTUAL MILEAGE

SERVICED BY:

Control Service.

7-22

I Maintenance Schedule I

0 Drain, flush and refill cooling system (or every 24 months, whichever occurs first). See “Engine Coolant” in the Index for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. An Emission Control Sewice. 17 Replace spark plugs. An Emission Control 0 Inspect spark plug wires. An Emission

Service. Control Service. T Replace air cleaner filter. Replace filter more often under dusty conditions. An Emission Control Service.

hspl ec t fuel tank, cap and lines for damage or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. An Emission Control Service. T

0 Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional mformation.

DATE

ACTUAL MILEAGE

SERVICED BY:

Maintenance Schedule 1 93,000 Miles (155 .OOO km)

Change engine oil and €firer (M every 3 months, wbichever occurs first). An Emission Control Service.

96,000 Miles (140 000 km) I7 Change engine ail and filter (or every

3 m-onths, whichever occurs first). An Emissiun Control Service. Lubricate the sbift linkage, parking brake cable guides, underbody contact paints and linkage (or every 6 months, whichever occurs first).

DATE

ACTUAL

MILEAGE

I Maintenance Schedule I 99,000 Miles (165 000 km) Cl Change engine oil and filter (or every

3 months, whichever occurs first). An Emission Control Service.

100,000 Miles (166 000 km) 0 Change automatic transaxle fluid and filter if the vehicle is mainly driven under one or more of these conditions: - In heavy city traffic where the outside

temperature regularly reaches 90 O F (32 O C) or higher.

- In hilly or mountainous terrain. - When doing frequent trailer towing. - Uses such as found in taxi, police or

delivery service.

DATE

ACTUAL MILEAGE

SERVICED BY:

If you do not use your vehicle under any of these conditions, the fluid an.dfilter do not require changing.

7-25

E i n t e n a n c e Scnedule I1 I

m m m

The services shown in this schedule up to 100,000 miles (166 000 km) should be performed after 100,000 miles (166 000 km) at the same intervals. Footnotes

The U.S. Environmental Protection Agency or the

California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of vehicle useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded.

7-26

7,500 Miles (12 500 km) 0 Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking braKe

cable guides, underbody contact points and linkage (or every 12 months, whichever occurs first).

0 Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional information.

DATE ACTUAL MILEAGE SERVICED

BY:

I Maintenance Schedule I1 15,000 Miles (25 000 km) 0 Change engine oil and filter (or every

12 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parlung brake cable guides, underbody contact points and linkage (or every 12 months, whichever occurs first).

DATE

ACTUAL MILEAGE

SERVICED BY:

22,500 Miles (37 500 km) 0 Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service.

17 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 12 months, whichever occurs first). Rotate tires. See “Tire Inspection and Rotation” in the Index for proper rotation pattern and additional information.

7-27

1 Maintenance Schedule I1 30,000 Miles (50 000 km) 0 Change engine oil and filter (or every

12 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 12 months, whichever occurs first). 0 Inspect engine accessory drive belt (or

every 24 months, whichever occurs first). An Emission Control Service. 0 Drain, flush and refill cooling system (or every 24 months, whichever occurs first). See “Engine Coolant” in the Index for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure test the cooling system and pressure cap. An Emission Control Service.

0 Replace spark pl 0 Inspect spark plug wires. An Emission

.ugS. An Emission

Control Service.

Control Service. f Replace air cleaner filter. An Emission Control Service.

0 Inspect fuel tank, cap and lines for damage

or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. An Emission Control Service.

4 Maintenance Schedule I1 I

37,500 Miles (62 500 km)

Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 12 months, whichever occurs first). Rotate tires. See “Tire Inspection and Rotation’’ in the Index for proper rotation pattern and additional information.

45,000 Miles (75 000 km) El Change engine oil and filter (or every

12 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 1 2 months, whichever occurs first).

DATE

ACTUAL MILEAGE

SERVICED BY:

DATE

ACTUAL MILEAGE

SERVICED BY:

7-29

50,000 Miles (83 000 km) 0 Change automatic transaxle fluid and filter

if the vehicle is mainly driven under one or more of these conditions: - In heavy city traffic where the outside

temperature regularly reaches 90 O F (32°C) or higher.

- In hilly or mountainous terrain. - When doing frequent trailer towing. - Uses such as found in taxi, police or If you do not use your vehicle under any of these conditions, the fluid andfilter do not require changing.

delivery service.

52,500 Miles (87 500 km) 0 Change engine oil and filter (or every

12 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 12 months, whichever occurs first). 0 Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional information.

DATE

ACTUAL MILEAGE

SERVICED B Y

DATE SERVICED

ACTUAL MILEAGE

B Y

7-30

Maintenance Schedule I1 60,000 Miles (100 000 km) 0 Change engine oil and filter (or every

12 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake

cable guides, underbody contact points and linkage (or every 12 months, whichever occurs first). 17 Inspect engine accessory drive belt (or

every 24 months, whichever occurs first). An Emission Control Service. Inspect camshaft timing belt. An Emission Control Service. 0 Drain, flush and refill cooling system (or every 24 months, whichever occurs first). See “Engine Coolant” in the Index for what to use. Inspect hoses. Clean radiator, condenser, pressure cap and neck. Pressure

test the cooling system and pressure cap. An Emission Control Service.

0 Replace spark plugs. An Emission 0 Inspect spark plug wires. An Emission

Control Service. Control Service, tf‘ Replace air cleaner filter. An Emission Control Service. Inspect fuel tank, cap and lines for damage or leaks. Inspect fuel cap gasket for any damage. Replace parts as needed. An Emission Control Service. -f-

DATE

ACTUAL MILEAGE

SERVICED BY:

7-3 1

67,500 Miles (112 500 km) c] Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 12 months, whichever occurs first).

0 Rotate tires. See “Tire Inspection and

Rotation” in the Index for proper rotation pattern and additional information.

75,000 Miles (125 000 km) Cl Change engine oil and filter (or every

12 months, whichever occurs first). An Emission Control Service.

0 Lubricate the shift linkage, parking brake cable guides, underbody contact points and linkage (or every 12 months, whichever occurs first).

0 Inspect camshaft timing belt. An Emission

Control Service.