10
12
PERIODIC
30
20
24
36
MAINTENANCE
SERVICE
40
48
50
60
60
72
AT
70
84
COST
80
96
WHEEL 1. Tyres (air pressure, abnormal wear, crack, ROTATION) 2. Wheels (damage) 3. Front wheel bearings (loose, damage) 4. Rear wheel bearings (loose, damage) FRONT AND REAR SUSPENSION 1. Suspension strut (oil leakage, damage) 2. Suspension arms and knuckle supports (loose.damage) 3. Rear spring (damage) 4. Shock absorbers (oil leakage, damage) 5. All bolts and nuts (loose) 6. Suspension arms and Tension rods STEERING 1. Steering wheel (play, loose) 2. Power steering fluid (level, leakage)/connections 3. All rods and arms (loose, damage, wear) ELECTRICAL 1. Battery electrolyte (level, leakage) 2. Wiring harness connection (looseness, damage) 3. Lighting system (operation, stains, damage) 4. Horn (operation) 5. System voltage BODY 1. All chassis bolts and nuts (tighten) 2. All Latches, Hinges & Locks (function)
9-5
Rotate and
I&L
inspect every 5,000
km
I&L
I&L
I&L
I&L
I&L
I&L
I&L
I&L
88
60G-74E
INSPECTION AND MAINTENANCE
Interval: This Interval should be judged by odometer reading or months, whichever comes first.
km (x 1,000) months
ROAD TEST 1. Operation of Brakes, Gear shifting & speedometer 2. Body and Chassis noise
AIR CONDITIONER (if equipped) 1. Check belt tension 2. Check Receiver Drier bubbles. 3. Tighten compressor mounting bolts 4. Check all hose joints, tighten if necessary 5. Check functioning of Recirc flap 6. Clean condenser with low pressure water 7. Check belt for frayed edges, change if necessary 8. Check all mounting bolts
.*
FREE
INSPECTIONS
—
10
12
PERIODIC
20
30
36
24
MAINTENANCE
SERVICE
40
48
50
60
60
72
AT,
70
84
COST
80
96
The rear shock absorbers are filled with high pressure gas. Never attempt to disassemble it or throw it into a fire. Avoid storing it near a heater or heating device. When scrapping the absorber, the gas must be released from the absorber safely. Ask your dealer for assistance.
89
INSPECTION AND MAINTENANCE
All maintenance should be carried out with the Ignition switch in the "OFF" position and the car parked securely on the level ground unless otherwise specified. If you are In any way unsure of your ability to undertake a task, then do not start it but contact your Maruti dealer to perform the work for you.
9-7
ENGINE OIL AND FILTER
Specified oil Be sure that the engine oil you use comes under the API classification of SF, SG or SH. Select the appropriate oil viscosity according to the above chart.
9-6
60G-74E
70F-07-004E
90
60G-74E
INSPECTION AND MAINTENANCE
60G-09-002E
60G-09-003E
60G-09-004
Oil Level Cheek
It is important to keep the engine oil at the
correct level for proper lubrication of your
vehicle's engine. Check the oil level with the
vehicle on a level surface. The oil level
indication may be inaccurate if the vehicle is
on a slope. The oil level should be checked
either before starting the engine or at least 5
minutes after stopping the engine.
Pull out the oil dipstick, wipe oil off with a clean
cloth, insert the dipstick all the way into the
engine, then remove it again. The oil on the
stick should be between the upper and lower
limits shown on the stick. If the oil level
indication is near the lower limit, add enough
oil to raise the level to the upper limit.
Refilling Remove the oil filler cap and pour oil slowly through the filler hole to bring the oil level to the upper limit on the dipstick. Be careful not to overfill. Too much oil is almost as bad as too little oil. After refilling, start the engine and allow it to idle for about a minute. Stop the engine, wait for five minutes and check the oil level again.
Changing Engine Oil and Fitter Drain the engine oil while the engine is still warm. 1) Remove the oil filler cap. 2) Place a drain pan under the drain plug. 3) Using the correct spanner remove the
drain plug and drain out the engine oil.
91
The engine oil temperature may be high enough to burn your fingers when the drain plug Is loosened. Watt until the drain plug is cool enough to touch with your bare hands.
9-8
60G-74E
INSPECTION AND MAINTENANCE
New and used oil can be hazardous. Children and pets may be harmed by swallowing new or used oil. Keep new and used oil and used oil fitters away from children and pets. Continuous contact with used engine oil has been found to cause (skin) cancer in laboratory animals. Brief contact with used oil may irritate skin. To minimize your exposure to used oil, wear a long-sleeve shirt and moistureproof gloves (such 'as dishwashing gloves) when changing oil. If oil contacts your skin, wash thoroughly with soap and water. Launder any clothing or rags if wet with oil. Recycle or properly dispose of used oil and filters.
4) Reinstall the drain plug and gasket. Tighten the plug to a torque of 5.0 kg-m (36.5 Ib-ft).
70F-07-010
60G-09-005
Replace the oil filter 1) Using an oil filter wrench, turn the oil filter
counterclockwise and remove it.
2) Using a clean rag, wipe off the mounting surface on the engine where the new filter will be seated.
3) Smear a little engine oil around the rubber
gasket of the new oil filter.
4) Screw on the new filter by hand until the filter gasket contacts the mounting surface.
CAUTION
To tighten the oil filter properly, it is important to accurately identify the position at which the filter gasket first contacts the mounting surface.
5) Tighten the filter 3/4 turn from the point of contact with the mounting surface, [or to 1.4 kg-m (10.5 Ib-ft)] using an oil filter wrench.
9-9
92
60G-74E
CAUTION
To prevent oil leakage, make sure that the oil filter is tight, but do not overtighten it.
INSPECTION AND MAINTENANCE
GEAR OIL
Refill with oil and check for leaks. 1) Pour 3.1 litres of oil through the filler hole
and install the filler cap.
2) Start the engine and look carefully for
leaks at the oil filter and drain plug. Run
the engine at various speeds for at least 5
minutes.
3) Stop the engine and wait for 5 minutes. Check the oil level again and add oil if necessary. Check for leaks again.
CAUTION
When replacing the oil filter, it is recommended that you use a genuine MARUTI replacement filter.
93
INSPECTION AND MAINTENANCE
70F-07-013E
Gear oil level check To check the gear oil level, use the following procedure: 1) Park the vehicle on a level surface with
the parking brake applied.
2) Clean casing around oil filler plug to remove risk of any loose dirt or debris entering oil filler plug hole. Remove the oil filler plug ©.
3) Feel the inside of the hole with your finger. If the oil level comes up to the bottom of the plug hole, the oil level is correct. If so, reinstall the plug.
4) If the oil level is low, add gear oil through the filler plug hole © until the oil level reaches the bottom of the filler hole, then reinstall the plug.
60G-09-006
70F-07-012E
CAUTION
indicate
Oil leaks from around the oil filter or drain plug incorrect installation or gasket damage. If you find any leaks or are not sure that the fitter has been properly tightened, have the vehicle inspected by your MARUTI dealer.
Oil filler and level plug © Tightening torque: 2.1 kg-m (15.5 Ib-ft)
Specified Manual Transmission oil When adding gear oil, use the appropriate viscosity and grade as shown in the chart below. We highly recommend you use API GL-4 SAE 75W-90 gear oil.
Type of oil
Gear oil, API GL-4
the vehicle,
After driving the transmission oil temperature may be high enough to burn you. Wait until the oil filler plug is cool enough to touch with your bare hands before inspecting transmission oil.
CAUTION
When tightening the plug, apply sealing compound to the plug threads to prevent oil leakage.
Gear oil change Since special procedures, materials and tools are required, it is recommended that you trust this job to your authorized MARUTI dealer.
9-10
60G-74E
ENGINE COOLANT
60G-09-007
Coolant Level Check Check the coolant level at the reservoir tank, not at the radiator. With the engine cool, the coolant level should be between the "FULL" and "LOW" marks.
Adding Coolant If the Coolant level is below the "LOW" mark, more coolant should be added. Remove the reservoir tank cap and add coolant until the reservoir tank level reaches the "FULL" mark. Never fill the reservoir tank above the "FULL" mark.
9-11
94
60G-74E
INSPECTION AND MAINTENANCE
CAUTION
If the
When adding or replacing coolant, use a high quality ethylene glycol antifreeze and anticorrosion (Non- Amine type) diluted with distilled water. lowest ambient temperature in your area is expected to be -15°C (5°F) or above, make the antifreeze concentration of the mixture you use at least 30% but no more than 50%. If -16°C (3°F) or below, make the concentration at least 50%. If the 50% concentration does not provide adequate protection against freezing, follow the instructions on the antifreeze container to obtain the desired freezing point. When putting the cap on the reservoir tank, line up the arrow on the cap and the arrow on the tank, or coolant can leak out.
95
INSPECTION AND MAINTENANCE
70F-07-019E
60G-09-039E
Coolant Replacement 1) When the engine is cool, remove the radiator cap by turning it slowly to the left until a "stop" is felt. Do not press down while turning the cap. Wait until any pressure is released, then press down on the cap and continue it anticlockwise.
turning
It is dangerous to remove the radiator cap when the water temperature is high, because scalding fluid and steam may be blown out under pressure. Watt until the coolant temperature has lowered before removing the cap.
2) Remove the reservoir tank cap. Remove the reservoir by lifting it up, and drain the reservoir completely by pouring the coolant in to a suitable container.
9-12
60G-74E
WINDSCREEN WASHER FLUID
AIR CLEANER
60G-09-008
63B-09-001
6OG-09-009
3) Loosen the drain plug attached to the lower part of the radiator and drain the coolant into a suitable container.
4) Tighten the drain plug on the radiator, fill the radiator with coolant and install the radiator cap.
5) Refit the reservoir and fill it with the correct coolant to the "FULL" line. Refit the reservoir tank cap, ensuring the arrows are correctly aligned.
CAUTION
The coolant must be replaced with the vehicle on level ground.
If the air cleaner is clogged with dust, there will be greater intake resistance, resulting in decreased power output and increased fuel consumption. Take out the air cleaner element after unhooking the clamps shown in the illustration. Blow off dust on air cleaner element by compressed air. If the air cleaner element appears to be dirty, replace it with a new one.
Check that there is washer fluid in the tank. Refill it if necessary. Use a good quality windscreen washer fluid, diluted with water as necessary.
Do not use "antifreeze" solution in the windscreen washer reservoir.This can severely impair visibility when sprayed on the windscreen, and can also damage your vehicle's paint.
CAUTION
Damage may result if the washer motor is operated whilst the fluid or fluid nozzles are frozen or with no fluid in the washer tank.
9-13
96
60G-74E
INSPECTION AND MAINTENANCE
SPARK PLUGS
60G-09-010E
60G-09-011E
60G-09-012E
CAUTION
The air cleaner element should be replaced every 40,000 km. More frequent replacement is necessary when you drive under dusty conditions.
You should inspect spark plugs periodically for carbon deposits. When carbon accumulates on a spark plug, a strong spark may not be produced. Remove carbon deposits with a wire or pin and adjust the spark plug gap.
97
INSPECTION AND MAINTENANCE
CAUTION
When disconnecting the spark plug cables, pull on the boot, not on the cable itself. Pulling on the cable can damage it. When installing the spark plugs, screw them in with your fingers to avoid stripping the threads.Tighten with a torque wrench to 2.0-3.0 kgm (20.0-30.0 N-m, 15.0-22.0 Ib-ft). Do not allow contaminants to enter the engine through the spark plug holes when the plugs are removed. Never use spark plugs with the wrong thread size or length.
9-14
60G-74E
BRAKES
70F-07-026E
60G-09-013E
60Q-09-014E
CAUTION
When replacing spark plugs, you should use the brand and type specified for your vehicle. For the specified plugs, the "SPECIFICATIONS" section at the end of this book.
refer
to
9-15
NOTE:
If you experience some firing problem of spark
plugs, such as, hard engine-starting, misfire
etc., the cause may be located not only on
spark plugs but also on deteriorated ignition
wiring (generally, used for more than 80,000
km or five years). If spark plug replacement
does not solve the problem, have the ignition
wiring and other ignition system inspected by
your MARUTI dealer.
Brake Fluid Check the brake fluid level by looking at the reservoir in the engine compartment. Check that the fluid level is between the "MAX" and "MIN" lines. If the brake fluid level is near the "MIN" line, fill it up to the "MAX" line with SAE J1703 or DOT-3 brake fluid.
Failure to follow the guidelines below can result in personal injury or serious damage to the brake system. •
If the brake fluid in the reservoir drops below a certain level, the brake warning light on the instrument
98
60G-74E
INSPECTION AND MAINTENANCE
Do not use any fluid other than SAE J1703 or DOT-3 brake fluid. Do not use reclaimed fluid or fluid that has been stored in old or open containers. It is essential that foreign particles and other liquids are kept out of the brake fluid reservoir.
CAUTION
70F-07-029
The brake fluid should be replaced every two years or 20,000 km.
NOTE: With disc brakes, the fluid level can be expected to gradually fall as the brake pads wear.
panel will come on (the engine must be running with the parking brake fully disengaged). Should the light come on, immediately ask your MARUTI dealer to inspect the brake system. A rapid fluid loss Indicates a leak in the brake system which should be inspected by your MARUTI dealer immediately. Brake fluid can harm your eyes and damage painted surfaces. Use caution when refilling the reservoir.
99
INSPECTION AND MAINTENANCE
70F-07-030
Brake Pedal
Check if the brake pedal stops at the regular
height without "spongy" feeling when you
depress it. If not, have the brake system
inspected by your MARUTI dealer. If you doubt
the brake pedal for the regular height, check
it as follows:
With the engine running, measure the distance
between the brake pedal and floor wall when
the pedal is depressed with approximately 30
kg (66 lbs) of force. The minimum distance
required is 80 mm (3.1 in). Since your vehicle's
brake system is self-adjusting, there is no need
for pedal adjustment. If the pedal to floor wall
distance as measured above is less than the
minimum distance required, have your vehicle
inspected by your MARUTI dealer.
9-16
60G-74E
STEERING
60G-09-015E
63B-09-00SE
60G-09-016
NOTE: When measuring the distance between the brake pedal and floor wall, be sure not to include any floor covering in the measurement.
If you experience any of the following problems with your vehicle's brake system, have the vehicle inspected immediately by your MARUTI dealer.
Poor braking performance Uneven braking (Brakes not working uniformly on all wheels.) Excessive pedal travel Brake dragging Excessive noise Pedal pulsation (Pedal pulsates when depressed.)
9-17
Parking brake Check the parking brake for proper adjustment by counting the number of clicks made by the ratchet teeth as you slowly pull up on the parking brake lever to the point of full engagement. The parking brake lever should stop between the 3rd and 5th ratchet tooth and the rear wheels should be securely locked. If the parking brake is not properly adjusted or the brakes drag after the lever has been fully released, have the parking brake inspected and/or adjusted by your MARUTI dealer.
Check the play of the steering wheel by gently turning it from left to right and measuring the distance that it moves before you feel slight resistance. The play should be between 0 - 30 mm (0.0 -1.2 in). Check that the steering wheel turns easily and smoothly without rattling by turning it all the way to the right and to the left while driving very slowly in an open area. If the amount of free play is outside the specification or you find anything else to be wrong, an inspection must be performed by your MARUTI dealer.
100
60G-74E
INSPECTION AND MAINTENANCE
POWER STEERING (if equipped)
CLUTCH PEDAL
60G-09-017
63B-09-00SE
70F-07-034
Check the steering box case, vane pump and hose connections for leaks or damage.
Power steering fluid Check the fluid level by looking at the reservoir in the engine compartment when the fluid is cold (about room temperature).
Check that the fluid level is between the "UPPER" and "LOWER" lines. If the fluid level is near the "LOWER" line, fill it up to the "UPPER" line with an automatic transmission fluid equivalent to DEXRON»-IIE or DEXRON'-III. Do not overfill.
101
INSPECTION AND MAINTENANCE
TYRES
60G-09-018
The front and rear tyre pressure specifications
for your vehicle are listed on the Tyre Inflation
Pressure Label and in the "SPECIFICATIONS"
section at the end of this book. Both the front
and rear tyres should have the specified tyre
pressure.
Tyre Inspection Inspect your vehicle's tyres periodically by performing the following checks: 1) Measure the air pressure with a tyre gauge. Adjust the pressure if necessary.
Power steering belt The tension of the belt should be such that there is a deflection of 8-10mm (0.31 -0.39 in.) when you press your thumb midway between the pulleys.
The belt should also be examined to ensure that it is not damaged. If necessary, have the belt adjusted or replaced by your MARUTI dealer.
Measure the clutch pedal piay by moving the clutch pedal with your hand and measuring the distance it moves until you feel slight resistance. The play in the clutch pedal should be between 1 5 - 20 mm (0.6 - 0.8 in). If the play is more or less than the above, or clutch dragging is felt with the pedal fully depressed, have the clutch inspected by your MARUTI dealer.
9-18
60G-74E
Air pressures should be checked when the tyres are cold or you may get inaccurate readings. Check the inflation pressure from time to time while inflating the tyre gradually, until the specified pressure is obtained. Never underinf late or overinf late the tyres. Underinflation can cause unusual handling characteristics or can cause the rim to slip on the tyre bead, resulting in an accident or damage to the tyre or rim. Overinflation can cause the tyre to burst, resulting in personal injury. Overinflation can also cause unusual handling characteristics which may result In an accident.
70F-07-037E
2) Check that the depth of the tread groove is more than 1.6 mm (0.06 in). To help you check this, the tyres have moulded in tread wear indicators in the grooves. When the indicators appear on the tread surface, the remaining depth of the tread is 1.6 mm (0.06 in) or less and the tyre should be replaced.
3) Check for abnormal wear, cracks and damage. Any tyres with cracks or other damage should be replaced. If any tyres show abnormal wear, have them inspected by your MARUTI dealer.
9-19
102
60G-74E
INSPECTION AND MAINTENANCE
Replacing the wheels and tyres equipped on your vehicle with certain combinations of aftermarket wheels and tyres can significantly change the steering and handling characteristics of your vehicle. Therefore, use only those wheel and tyre combinations approved by MARUTI as standard or optional equipment for your vehicle.
CAUTION
Replacing the original tyres with tyres of a different size may result in false speedometer or odometer readings.
Hitting curbs and running over rocks can damage tyres and affect wheel alignment. Be sure to have tyres and wheel alignment checked periodically by your MARUTI dealer.
4) Check for loose wheel nuts. 5) Check that there are no nails, stones, or
other objects sticking into the tyres.
Your MARUTI is equipped with tyres which are all the same type and size. This is important to ensure proper steering and handling of the vehicle. Never mix tyres of different size or type on the four wheels of your vehicle. The size and type of tyres used should be only those approved by MARUTI as standard or optional equipment for your vehicle.
103
INSPECTION AND MAINTENANCE
60G-09-019E
Tyre Rotation To avoid uneven wear of your tyres and to prolong their life, rotate the tyres as illustrated. Tyres should be rotated every 5,000 km as recommended in the periodic maintenance schedule. After rotation, adjust front and rear tyre pressures to the specification listed on your vehicle's Tyre Inflation Pressure Label.
9-20
60G-74E
60G-06-009
60G-09-020E
60G-09-021
Changing Wheels To change a wheel, use the following procedure: 1) Remove the jack , tools and spare wheel
from the vehicle
5)
Install the new wheel and replace the wheel nuts with their cone shaped end facing the wheel. Tighten each nut snugly by hand until the wheel is securely seated on the hub.
Full Wheel Cover (if equipped) Your vehicle includes a jack crank, which has a flat end. Use the jack crank to remove the full wheel cap, as shown above.
2) Loosen, but do not remove the wheel nuts. '
3) Jack up the vehicle (follow the jacking the EMERGENCY
instructions SERVICE section in this manual)
in
Lower the jack and fully tighten the nuts [to 8.5 kg-m (61.5 Ib-ft)] in a crisscross fashion with a wrench as shown in the illustration.
4) Remove the wheel nuts and wheel.
9-21
104
60G-74E
INSPECTION AND MAINTENANCE
BATTERY
To avoid harm to yourself or damage to your vehicle or battery, follow the jump starting instructions in the EMERGENCY SERVICE section of this manual if it is necessary to jump start your vehicle.
The level of the battery solution must be kept between the "UPPER" and the "LOWER" level lines at all times. If the level is found to be below the "LOWER" level line, add distilled water to the "UPPER" level line. You should periodically check the battery, battery terminals, and battery holddown bracket for corrosion. Remove corrosion using a stiff brush and ammonia mixed with water, or baking soda mixed with water. After removing corrosion, rinse with clean water.
If your vehicle is not going to be driven for a month or longer, disconnect the cable from the negative terminal of the battery to help prevent discharge.
9-22
60G-74E
60G-09-022E
60G-09-038
When installing the cover, make sure that it is positioned so that it does not cover or foul the air valve.
Batteries produce flammable hydrogen gas. Keep flames and sparks away from the battery or an explosion may occur. Never smoke when working in the vicinity of the battery .
When checking or servicing the battery, disconnect the negative cable. Be careful not to cause a short circuit by allowing metal objects to contact the battery posts and the vehicle at the same time.
105
INSPECTION AND MAINTENANCE
FUSES
MAIN FUSE / PRIMARY FUSES 80A 60A
All Electric Load HEAD-R, HEAD-L, TAIL/DOME, STOP/HORN, HAZARD CIGAR/RADIO, I.G. COIL/ METER, WIPER/WASHER, REAR DEF, TURN/BACK, HEATER RELAY. RADIATOR FAN MOTOR A/C, HTR
60A
30A 60A
60G-09-024E
©. Main fuse ®. Primary fuse (Lights) ®. Primary fuse (IG) ©. Radiator fan motor fuse ©. Primary fuse (A/C, HTR) This vehicle has three types of fuses, as described below: Main Fuse - The main fuse takes current directly from the battery. Primary Fuses - These fuses are between the main fuse and individual fuses, and are for electrical load groups. Individual Fuses - These fuses are in the fuse box and for individual electrical circuits.
9-23
Main Fuse and Primary Fuses The main fuse and primary fuses are located in the engine compartment. If the main fuse blows, no electrical component will function. If a primary fuse blows, no electrical component in the corresponding load group will function. When replacing the main fuse or a primary fuse, use a genuine MARUTI replacement.
60G-09-025E
Fuse Box The fuse boxes are located in the engine compartment and under the driver's side of the dashboard.
To remove the fuse box cover under the dashboard pull off the cover.
If the main fuse or a primary fuse blows, be sure to have your vehicle inspected by an authorized MARUTI dealer. Always use a genuine MARUTI replacement. Never use a substitute such as a wire even for a temporary repair, or extensive electrical damage and a fire can result.
106
60G-74E
INSPECTION AND MAINTENANCE
60G-09-026
60G-09-027E
70F-07-04SE
Always be sure to replace a blown fuse with a fuse of the correct amperage. Never use a substitute such as aluminium foil or wire to replace a blown fuse. If you replace a fuse and the new one blows In a short period of time, you may have a major electrical problem. Have your vehicle Inspected immediately by your MARUTI dealer.
107
INSPECTION AND MAINTENANCE
BULB REPLACEMENT
Light bulbs can be hot enough to burn your finger right after being turned off.This is true especially for halogen headlight bulbs. Replace the bulbs after they become cool enough. The headlight bulbs are filled with pressurized halogen gas. They can burst and injure you if they are hit or dropped. Handle them carefully.
CAUTION
The oils from your skin may cause a halogen bulb to overheat and burst when the lights are on. Grasp a new bulb with a clean cloth.
CAUTION
Frequent replacement of a bulb indicates the need for an inspection of the electrical system. This should be carried out by your MARUTI dealer.
NOTE: Make sure that the fuse box always carries spare fuses.
60G-09-028E
9-24
60G-74E
60G-09-029
60G-09-030
Interior Light Press down the lens by using a plain screw driver covered with a soft cloth as shown. To install it, simply push it back in. The bulb can be removed by simply pulling it out. When replacing the bulb, make sure that the contact springs are holding the bulb securely.
NOTE: If the air cleaner inlet duct (A) obstructs replacement of the bulbs in the right headlight housing, remove the duct (A).
After reinstalling the duct, make sure it is secured in place
9-25
108
60G-74E
INSPECTION AND MAINTENANCE
60G-09-031
60G-09-037
70F-07-0S0E
Headlights Open the bonnet. Disconnect the coupler.Turn the lock ring counterclockwise and remove it. Remove the sealing rubber.
NOTE: Your vehicle is provided with two spare headlight bulbs in emegency.
replacement
for
Push the retaining spring forward and unhook it. Then remove the bulb. Install a new bulb in the reverse order of removal.
NOTE: Your vehicle is provided with two spare headlight bulbs for replacement in emergency situations.
Front Clearance/Turn Signal Light, Side Turn Signal Light, rear Combination Light, Registration Plate Light. To remove a bulb holder from a light housing, turn the holder counterclockwise and pull it out. To install the holder, push the holder in and turn it clockwise.
Two types (small oval and round) of bulb are used for these lights. To remove and install a small oval bulb, simply pull out or push in the bulb.
109
INSPECTION AND MAINTENANCE
9-26
60G-74E
70F-07-051E
60G-09-032
70F-07-054
To remove a round bulb from a bulb holder, push in the bulb and turn it counterclockwise. To install a new bulb, push it in and turn it clockwise. You can access the individual bulb holders as described above:
Front clearance light (A) Open the bonnet.
Front turn signal light (B) Trust this replacement job to your authorized MARUTI dealer as the front bumper and the headlight housing must be removed for this job.
Side turn signal light Remove the lens by using a plain screw driver covered with a soft cloth.
9-27
110
60G-74E
INSPECTION AND MAINTENANCE
60G-09-033
60G-09-034
60G-09-035
Rear combination light (tail, stop, turn Registration plate tight signal, etc.) Undo the screws that secure the housing and housing. remove the housing by sliding in the direction of the white arrow in the illustration.
Undo the two screws and remove the light Turn the lens counterclockwise and pull it off.
Trunk (boot) light (if equipped)
111
INSPECTION AND MAINTENANCE
WIPER BLADES
60G-09-036
70F-07-059
High mount stop light Trust this replacement job to your authorized MARUTI dealer.
If the wiper blades become brittle or damaged, or make streaks when wiping, replace the wiper blades. To install new wiper blades, follow the procedure below.
CAUTION
To avoid scratching or breaking the window, do not let the wiper arm strike the windshield while replacing the wiper blade.
9-28
60G-74E
NOTE: Some wiper blades may be different from the ones described here depending on vehicle specifications. If so consult your MARUTI dealer for proper replacement method.
The left and the right wiper arm assemblies are different from each other. In case you have to remove the wiper arm assemblies for any reason, remember not to interchange the two while fitting them back. Wrong fitment may lead to windshield breakage.
9-29
112
60G-74E
INSPECTION AND MAINTENANCE
70F-07-060
72F-09-008
For windshield wipers: 1. Hold the wiper arm away from the
window.
2. Squeeze lock lever (A) towards wiper arms (B) and remove the wiper frame from the arm as shown.
113
60G-74E
EMERGENCY SERVICE
Jacking Instructions Jump Starting Instructions Towing Emergency Remedies Warning Triangle
9-30
EMERGENCY SERVICE
10-1
10-2
10-4
10-4
10-5
115
60G-74E
INSPECTION AND MAINTENANCE
70F-07-060
72F-09-008
For windshield wipers: 1. Hold the wiper arm away from the
window.
2. Squeeze lock lever (A) towards wiper arms (B) and remove the wiper frame from the arm as shown.
113
60G-74E
EMERGENCY SERVICE
Jacking Instructions Jump Starting Instructions Towing Emergency Remedies Warning Triangle
9-30
EMERGENCY SERVICE
10-1
10-2
10-4
10-4
10-5
115
EMERGENCY SERVICE
JACKING INSTRUCTIONS
60G-74E
60G-06-009
63B-10-001E
70F-08-001
1) Park the vehicle securely on hard level
ground.
2) Apply the parking brake firmly and shift into "R" (Reverse). Choke the front and rear wheel diagonally opposite the wheel to be changed. 3) Switch on the hazard warning flasher if your
vehicle is in or near traffic.
4) Slacken but do not remove wheel nuts on the
wheel to be changed.
5) Position the jack vertically and raise the jack by turning the jack handle clockwise until the jack head recess fits the frame boss.
6) Continue to raise the jack slowly and smoothly until the tyre clears the ground. Do not raise the vehicle more than necessary.
10-1
60G-74E
60G-10-001
NOTE: Use the wheel nut wrench in combination with jack crank to raise or lower the jack as shown in the illustration.
Use the jack only to change wheels. Never jack up the vehicle on an inclined surface. Never raise the vehicle with the jack in a location other than under the frame boss near the wheel to be changed. Make sure that the jack is raised at least 2 inches (51 mm) before it contacts the vehicle. Use of the jack when it is within 2 inches of being fully collapsed may result in failure of the jack. Never get under the vehicle when it is supported by the jack. t=>
116
EMERGENCY SERVICE
JUMP STARTING INSTRUCTIONS
60G-10-002
60G-10-003
Never run the engine when the vehicle is supported by the jack and never allow passengers to remain in the vehicle.
jump
Never attempt to jump start your vehicle if the battery appears to be frozen. Batteries in this condition may explode or rupture if jump starting is attempted. When making lead connections, be certain that your hands and the Jump leads remain clear from pulleys, belts, or fans. Batteries produce flammable hydrogen gas. Keep flames and sparks away from the battery or an explosion may occur. Never smoke when working in the vicinity of the battery. If the booster battery you use for jump starting is installed in another vehicle, make sure the two vehicles are not touching each other. If discharges repeatedly, for no apparent reason, have your vehicle inspected by an authorized MARUTI dealer. To avoid harm to yourself or damage to your vehicle or battery, follow the jump starting instructions below precisely and in order. If you are in doubt, call for qualified road service.
battery
your
10-2
EMERGENCY SERVICE
60G-74E
CAUTION
Vehicle equipped with electronic fuel injection system will not start by pushing or towing as the fuel pump will not work in this condition. This starting method could also result in permanent damage to the catalytic converter. Use jump leads to start a vehicle with a weak or flat battery.
60G-10-004E
When jump starting your vehicle, use the following procedure: 1) Use only a 12 volt battery to jump start your vehicle. Position the good 12V battery close to your vehicle so that the jump leads will reach both batteries. When using a battery installed on another vehicle, DO NOT LET THE VEHICLES TOUCH. Apply the parking brakes fully on both vehicles. 2) Turn off all vehicle accessories, except those necessary for safety reasons (for example, headlights or hazard lights).
3) Make jump lead connections as follows:
a) Connect one end of the first jump lead to the positive (+) terminal of the flat battery.
b) Connect the other end to the positive
(+) terminal of the booster battery.
c) Connect one end of the second jump lead to the negative (-) terminal of the booster battery.
d) Make the final connection to an unpainted, heavy metal part of the engine of the vehicle with the flat battery.
Never connect the jump lead directly to the negative (-) terminal of the discharged battery, or an explosion may occur.
4) If the booster battery you are using is fitted to another vehicle, start the engine of the vehicle with the booster battery. Run the engine at moderate speed.
5) Start the engine of the vehicle with the flat
battery.
6) Remove the jump leads in the exact reverse order in which you connected them.
10-3
60G-74E
TOWING
If you need to have your vehicle towed, contact a professional service.
CAUTION
To help avoid damage to your vehicle during towing, proper equipment and towing procedures must be used.
Manual Transmission Whenever possible, your vehicle should be towed from the front with the front wheels lifted. If the steering and drivetrain are in good condition, your vehicle may be towed from the rear with the rear wheels lifted and the front wheels on the ground. Before towing, make sure the steering is unlocked and the transmission is in neutral.
118
EMERGENCY REMEDIES
If the Starter Does Not Operate: 1) Try turning the ignition switch to the "START" position with the headlights turned on to determine the battery condition. If the headlights go excessively dim or go off, it usually means that either the battery is flat or the battery terminal contact is poor. Recharge the battery or correct battery terminal contact as necessary. If the headlights remain bright, check the fuses. If the reason for failure of the starter is not obvious, there may be a major electrical problem. Have the vehicle inspected by your authorized MARUTI dealer.
2)
If the Engine is Flooded If the engine is flooded with petrol, it may be hard to start. If this happens, press the accelerator pedal all the way to the floor and hold it there while cranking the engine. (Do not operate the starter motor for more than 15 seconds). Release the accelerator as soon as the engine has started.
EMERGENCY SERVICE
If the Engine Overheats The engine could overheat temporarily under severe driving conditions. If the engine coolant temperature gauge indicates overheating during driving:
1) Turn off the air conditioner, if equipped. 2) Take the vehicle to a safe place and park. 3) Let the engine run at normal idle speed for a few minutes until the indicator is within the normal, acceptable temperature range between "H" and "C".
If you see or hear escaping steam, stop the vehicle in a safe place and Immediately turn off the engine to let it cool. Do not open the bonnet when steam is present. When the steam can no longer be seen or heard, open the hood to see if the coolant is still boiling. If it is, you must wait until it stops boiling before you proceed.
119
10-4
EMERGENCY SERVICE
If the temperature indication does not come down to within the normal, acceptable range: 1) Turn off the engine and check that the water pump belt and pulleys are not damaged or slipping. If any abnormality is found, correct it.
2) Check the coolant level in the reservoir. If it is found to be lower than the "LOW" line, look for leaks at the radiator, water pump, and radiator and heater hoses. If you locate any leaks that may have caused the overheating, do not run the engine until these problems have been corrected.
3) If you do not find a leak, carefully add coolant to the reservoir and then the radiator, if necessary. (Refer to "ENGINE COOLANr in the "INSPECTION AND MAINTENANCE" section.)
10-5
60G-74E
WARNING TRIANGLE (TYPE-2)
In case of vehicle breakdown or during emergency stopping where your vehicle could become a potential traffic hazard, keep the warning triangle, provided with your vehicle, on the road free from any obstacles behind your vehicle so as to warn the approaching traffic, at an approximate distance of 50-100 m, the reflecting side of the triangle should face the on coming traffic. Please activate the hazard warning lamps before alighting the vehicle to keep the warning triangle.
WARNING TRIANGLE (TYPE-1)
60G-74E
843-10-004
In case of vehicle break-down or during emergency stopping where your vehicle could become a potential traffic hazard, please keep the warning triangle, provided with your vehicle, on the pathway (road) behind the vehicle so as to warn the approaching traffic, at an approximate distance of 5-15 m, such that reflecting side of the triangle faces the rear. Please activate the hazard warning lamps before alighting the vehicle to keep the warning triangle.
K is dangerous to remove the radiator cap when the water temperature is high, because scalding fluid and steam may be blown out under pressure. The cap should only be taken off when the coolant temperature has lowered.
To help prevent personal Injury, keep hands, tools and clothing away from the engine cooling fan and airconditioner fan (if equipped). These electric fans can automatically turn on without warning.
120
EMERGENCY SERVICE
the warning
Remove triangle carefully from the box as shown by arrow 1. Open both the reflector arms as shown by arrows and lock arms with each other with the clip provided in the right arm. Open the bottom stand in counter clock- wise direction as shown by arrow 3. Position the warning triangle behind the vehicle on a plain surface. Reverse keeping inside the box.
the removal procedure
for
121
10-6
60G-74E
BODY WORK CARE
Corrosion Prevention Vehicle Cleaning
BODY WORK CARE
11-1
11-2
123
BODY WORK CARE
CORROSION PREVENTION
It is important to take good care of your vehicle to protect it from corrosion. Listed below are instructions for how to maintain your vehicle to prevent corrosion. Please read and follow these instructions carefully.
Important Information About Corrosion Common causes of corrosion 1) Accumulation of road salt, dirt, moisture, or chemicals in hard to reach areas of the vehicle underbody or frame.
2) Chipping, scratches and any damage to treated or painted metal surfaces resulting from minor accidents or abrasion by stones and gravel.
Environmental conditions which accelerate corrosion 1) Road salt, dust control chemicals, sea air or industrial pollution will all accelerate the corrosion of metal.
2) High humidity will increase the rate of corrosion particularly when the temperature range is just above the freezing point.
3) Moisture in certain areas of a vehicle for an extended period of time may promote corrosion even though other body sections may be completely dry.
4) High
temperatures will cause an accelerated rate of corrosion to parts of the vehicle which are not well ventilated to permit quick drying.
This information illustrates the necessity of keeping your vehicle (particularly the underbody) as clean and dry as possible. It is equally important to repair any damage to the paint or protective coatings as soon as possible.
How to Help Prevent Corrosion Wash your vehicle frequently The best way to preserve the finish on your vehicle and to help avoid corrosion is to keep it clean with frequent washing. Wash your vehicle regularly during the winter and immediately after the winter. Keep your vehicle, particularly the underside, as clean and dry as possible. If you frequently drive on salted roads, your vehicle should be washed at least once a month during the winter. If you live near the ocean, your vehicle should be washed at least once a month throughout the year. For washing instructions, refer to the "VEHICLE CLEANING" section. Remove foreign material deposits Foreign material such as salts, chemicals, road oil or tar, tree sap, bird droppings and industrial fall-out may damage the finish of your vehicle
60G-74E
if it is left on painted surfaces. Remove these types of deposits as quickly as possible. If these deposits are difficult to wash off, an additional cleaner may be required. Be sure that any cleaner you use is not harmful to painted surfaces and is specifically intended for your purposes. Follow the manufacturer's directions when using these special cleaners. Repair finish damage Carefully examine your vehicle for damage to the painted surfaces. Should you find any chips or scratches in the paint, touch them up immediately to prevent corrosion from starting. If the chips or scratches have gone through to the bare metal, have a qualified body shop make the repair. Keep Passenger compartments clean. Moisture, dirt or mud can accumulate under the floor mats and may cause corrosion. Occasionally, check under these mats to ensure that this area is clean and dry. More frequent checks are necessary if the vehicle is used off road or in wet weather. Certain cargos such as chemicals, fertilizers, cleaners, salts, etc., are extremely corrosive by nature. These products should be transported in sealed containers. If a spill or leak does occur, clean and dry the area immediately.
luggage
and
11-1
124
60G-74E
BODY WORK CARE
Store your vehicle in a dry, well-ventilated area. Do not park your vehicle in a damp, poorly ventilated area. If you often wash your vehicle in the garage or if you frequently drive it in when wet, your garage may be damp.The high humidity in the garage may cause or accelerate corrosion. A wet vehicle may corrode even in a heated garage if the ventilation is poor.
Do not apply additional undercoating or rust preventive coating on or around exhaust system components such as the exhaust pipes, etc. A fire could be started if the undercoating substance becomes overheated.
Cover your vehicle If you cannot regularly park your vehicle in a garage, we recommend you use a vehicle cover. Years of exposure to midday sun can cause the colours in paint, plastic parts, and fabrics to fade. Covering your vehicle with a high-quaiity, "breathable" vehicle cover can help protect the finish from the harmful UV rays in sunlight, and can reduce the amount of dust and air pollution reaching the surface.
125
VEHICLE CLEANING
When cleaning the interior or exterior of the vehicle, NEVER USE flammable solvents such as lacquer thinners, petrol, benzene or cleaning materials such as bleach or strong household detergents. The materials could cause personal injury or damage to the vehicle.
Cleaning the Interior Vinyl upholstery Prepare a solution of soap or mild detergent mixed with warm water. Apply the solution to the vinyl with a sponge or soft cloth and let it soak for a few minutes to loosen dirt. Rub the surface with a clean, damp cloth to remove dirt and the soap solution. If some dirt still remains on the surface, repeat this procedure. Fabric upholstery Remove loose dirt with a vacuum cleaner. Using a mild soap solution, rub stained areas with a clean damp cloth. To remove soap, rub the areas again with a cloth dampened with water. Repeat this until the stain is removed, or use a commercial fabric cleaner for tougher stains. If you use a fabric cleaner, carefully follow the manufacturer's instructions and precautions.
BODY WORK CARE
Cleaning the Exterior
CAUTION
It is important that your vehicle be kept clean and free from dirt. Failure to keep your vehicle clean may result in fading of the paint or corrosion to various parts of the vehicle body.
Washing
Never attempt to wash and wax your vehicle with the engine running. When cleaning the underside of the body and fender, where there may be sharp-edged parts, you should wear gloves and a longsleeved shirt to protect your hands and arms from being cut. After washing your vehicle, carefully test the brakes before driving to make sure they have maintained their normal effectiveness.
When washing the vehicle, follow the instructions below: 1) Flush the underside of body and wheel housings with pressurized water to remove mud and debris. Use plenty of water.
CAUTION
When washing the vehicle, avoid directing steam or hot water of more than 80°C (176°F) on plastic parts.
2) Remove dirt and mud from the body exterior with running water. You may use a soft sponge or brush. Do not use hard materials which can scratch the paint.
3) Wash the entire exterior with a mild detergent or car wash soap using a sponge or soft cloth. The sponge or cloth should be frequently soaked in the soap solution.
CAUTION
When using a commercial car wash product, observe the cautions specified by the manufacturer. Never use strong household detergents or soaps.
Seat Belts Clean seat belts with a mild soap and water. Do not use bleach or dye on the belts. They may weaken the fabric in the belts. Vinyl floor mats Ordinary dirt can be removed from vinyl with water or mild soap. Use a brush to help loosen dirt. After the dirt is loosened, rinse the mat thoroughly with water and dry it in the shade. Carpets Remove dirt and soil as much as possible with a vacuum cleaner. Using a mild soap solution, rub stained areas with a clean damp cloth.To remove soap, rub the areas again with a cloth dampened with water. Repeat this until the stain is removed, or use a commercial carpet cleaner for tougher stains. If you use a carpet cleaner, carefully follow the manufacturer's instructions and precautions.
11-2
60G-74E
4) Once the dirt has been completely removed, rinse off the detergent with running water.
5) After rinsing, wipe off the vehicle body with a wet chamois or cloth and allow it to dry in the shade.
6) Check carefully for damage to painted surfaces. If there is any damage, "Touchup" the damage following the procedure below: a) Clean all damaged spots and allow
them to dry.
b) Stir the paint and "touchup" the damaged spots lightly using a small brush.
c) Allow the paint to dry completely.
Waxing After washing the vehicle, waxing and polishing are recommended to further protect and beautify the paint. • Only use waxes and polishes of good