1997 Oldsmobile Bravada Owners Manual

.. .

The 1997 Oldsmobile Bravada Owner’s Manual

1-1

2- 1

3-1

4- 1

5- 1

6- 1

7-1

8- 1

9- 1

Seats and Restraint Systems This section tells you how t o use your seats and safety belts properly. It also explains the “SIR” system. Features and Controls This section explains how t o start and operate your Oldsmobile. Comfort Controls and Audio Systems This section tells you how to ad-just the ventilation and comfort controls and how to operate your audio system. Your Driving and the Road Here you’ll find helpful information and tips about the road and how to drive under different conditions. Problems on the Road This section tells what to do if you have a problem while driving, such as a flat tire or overheated engine. etc. Service and Appearance Care Here the manual tells you how to keep your Oldsmobile running properly and looking good. Maintenance Schedule This section tells you when to perform vehicle maintenance and what fluids and lubricants t o use. Customer Assistance Information This section tells you how to contact Oldsmobile for assistance and how to get service and owner publications. It also gives you information on “Reporting Safety Defects” on page 8-8. Index Here‘s an alphabetical listing of almost every subject i n this manual. You can use it to quickly find something you want to read.

GENERAL MOTORS, GM, the GM Emblem, OLDSMOBILE, the OLDSMOBILE Rocket Emblem and the name BRAVADA are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes in the product after that time without further notice. Please keep this manual in your Oldsmobile, so it will be there if you ever need it when you’re on the road. If you sell the vehicle, please leave this manual in it so the new owner can use it.

We support voluntary technician certification.

-I-

WE SUPPORT

VOLUNTARY TECHNICIAN CERTIFICATION THROUGH

National Institute for

A U T O M O T I V E

S E R V I C E

E X C E L L E N C E

About Driving Your Bravada As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident. Be sure to read the “on-pavement” and “off-road” driving guidelines in this manual. (See “Driving Guidelines” and “Operating Your Oldsmobile Off Paved Roads” in the Index.)

Litho in U.S.A. Part No. 22652548 A First Edition

@Copyright General Motors Corporation 1996 All Rights Reserved

How to Use this Manual Many people read their owner’s manual from beginning to end when they first receive their new vehicle. If you do this, it will help you learn about the features and controls for your vehicle. In this 111anua1, you’ll find that pictures and words work together to explain things quicklv. Index A good place to look for what you need is the Index i n the back of the manual. It‘s an alphabetical list of all that’s in the manual, and the page number where you’ll find it. Safety Warnings and Symbols You will find a number of safety cautions i n this book. We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning.

These mean there is something that could hurt you or other people.

In the caution area, we tell you what the hazard is. Then we tell you what to do to help avoid or reduce the hazxd. Please read these cautions. If you don’t: you or others could be hurt.

You will also find a circle with a slash througln it in this book. This safe:ty symbol means “Don’t,’’ ”Don’t do this.‘‘ or “Don‘t let this happen.“

iii

Vehicle Damage Warnings Also in this book you will find these not.ices:

I NOTICE:

These mean there is something that could damage your vehicle.

In the notice area, we tell you about something that can darnage your vehicle. Many times, this damage would not be covered by your warranty, and it could be costly. But the notice will tell you what to do to help avoid the damage. When you read other manuals, you might see CAUTION and NOTICE warnings in different colors or in different words. You’ll also see warning labels on your vehicle. They use the same words, CAUTION or NOTICE.

iv

Vehicle Symbols These are some of the symbols you may find on your vehicle.

For exumple, thesc bymbols aIe used on an original battery:

CAUTION POSSIBLE INJURY

PROTECT EYES BY SHIELDING

CAUSTIC BATTERY ACID COULD CAUSE BURNS

AVOID SPARKS OR FLAMES

SPARK OR FLAME COULD EXPLODE BATTERY

6 @

TURN SIGNALS

WINDSHIELD WIPER

WINDSHIELD DEFROSTER

DOOR LOCK UNLOCK

FASTEN SEAT BELTS

WINDOW f

POWER

'* _ _ I

,111,

WINDOW DEFOGGER

DAYTIME . .

RUNNING *

LAMPS * ' *

# 0

VENTILATING

FOG LAMPS

These sylnbols are used on warning a n d indicator lights:

Here are some other synbols you may see:

COOLANT TEMP

BATTERY CHARGING SYSTEM

BRAKE

COOLANT

I-1 (a)

FUSE

LIGHTER

HORN )tr SPEAKER b I&

FUEL

**

ENGINE OIL PRESSURE W

ANTI-LOCK (@)

BRAKES

Model Reference

This manual .covers this model: I Four-Door Utility

a Section 1 Seats and Restraint Systems

Here you’ll find information about the seats in your Oldsmobile and how to use your safety belts properly. You can also learn about some things you should not do with air bags and safety belts.

1-2 1-2 1-2 1-3 1-5 1-7 1- 10

1-1 1

Seats and Controls Manual Passenger’s Seat Power Driver’s Seat Reclining Front Seatbacks Rear Seats Why Safety Belts Work Questions Many People Ask About Safety Belts How to Wear Safety Belts Properly

1-20 1-24 1-34 1-34

1-35 1-44 1-44 1-45

Child Restraints

Questions and Answers About Air Bags Safety Belt Use During Pregnancy How to Use Important Information for Buckling Children in Child Restraints Child Restraint Top Straps How to Obtain a Safety Belt Extender Checking Your Restraint Systems Replacing Parts After a Crash

Seats and Seat Controls This section tells you about the seats -- how to adjust them, and fold them up and down. Manual Passenger’s Seat

Power Driver’s Seat

The control pad is on the driver’s seat. Use the front control to make the front of the seat move up or down. To make the rear of the seat move up or down, use the rear control. Use the center control to move the whole seat up, down, forward or backward.

1-2

Power Lumbar Control

Reclining Front Seatbacks

The control is on the side of the driver's or passenger's seat. Press and hold the front of the control ~ ~ n t i l you have the desired lumbar support. To decrease lumbar support, press the rear of the control.

To ad-just the seatback, lift the lever OKI the outer side of the seat. Release the lever to lock the seatback where you want it. Pull up on the lever and the seat will go to an upright position.

3

Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this. The shoulder belt can’t do its job because it won’t be against your body. Instead, it will be in front of you. In a crash you could go into it, receiving neck or other injuries. The lap belt can’t do its job either. In a crash the belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries. For proper protection when the vehicle is in motion, have the seatback upright. Then sit well back in the seat and wear your safety belt properly.

But don’t have a seatback reclined if your vehicle is moving.

Head Restraints Slide the head restraint 1:p or down so that the top of the restraint is closest to the top of your ears. This position reduces the chance of a neck injury in a crash. The head restraints tilt forward and rearward also.

Rear Seats

Your vehicle has a folding rear seat which lets you fold the seatbacks down for more cargo space. The rear seat release handles are in the upper center of the rear of the seatbacks. Push back on the seatbacks as you pull up on the handles. To raise the seatbacks, just lift up the seatbacks and push until they lock in the upright position. Push and pull on the seatbacks to check that the latches have locked i n the upright position. If they haven't, have them fixed immediately.

1-5

Safety Belts: They’re for Everyone This part of the rnanual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. And it explains the Supplemental Inflatable Restraint (SIR), or air bag system.

Don’t let anyone ride where he or she can’t wear a safety belt properly. If you are in a crash and you’re not wearing a safety belt, your injuries can be much worse. You can hit things inside the vehicle or be ejected from it. You can be seriously injured or killed. In the same crash, you might not be if you are buckled up. Always fasten your safety belt, and check that your passengers’ belts are fastened properly too.

1-6

CdJTION:

likely to be

It is extremely dangerous to ride in a cargo area, inside or outside of’ a vehicle. In a collision, people riding in these areas are more seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a

safety belt properly. 1 Your vehicle has a light that

comes on as a reminder to buckle up. (See “Safety Belt Reminder Light” in the Index.)

Why Safety Belts Work When you ride in or on anything, you go as fast as it goes.

In most states and Canadian provinces, the law says to wear safety belts. Here’s why: The!! work. You never know if you’ll be in a crash. If you do have a crash, you don’t know if it will be a bad one. A few crashes are mild, and some crashes can be so serious that even buckled up a person wouldn’t survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away. Without belts they could have been badly hurt or killed. After more than 25 years of safety belts in vehicles, the facts are clear. In most crashes buckling up does matter ... a lot!

Take the simplest vehicle. Suppose it’s just a seat on wheels.

1-7

Put someone on it.

Get it up to speed. Then stop the vehicle. The rider doesn't stop.

1-8

The person keeps going until stopped by something. In a real vehicle, it could be the windshield ...

or the instrument panel ...

1-9

accident if I'm wearing a safety belt?

Here Are Questions Many People Ask About Safety Belts -- and the Answers e.' Won't I be trapped in the vehicle after an A: You could be -- whether you're wearing a safety belt or not. But you can unbuckle a safety belt, even if you're upside down. And your chance of being conscious during and after an accident, so you C'CIM unbuckle and get out, is rwch greater if you are belted.

Q.' If my vehicle has air bags, why should I have to

wear safety belts?

A: Air bags are in many vehicles today and will be in

most of them i n the future. But they are supplemental systems only; so they work with safety belts -- not instead of them. Every air bag system ever offered for sale has required the use of safety belts. Even if you're in a vehicle that has air bags, you still have to buckle up to get the most protection. That's true not only in frontal collisions, but especially i n side and other collisions.

or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That's why safety belts make such good sense.

1-10

home, why should I wear safety belts?

&= If I’m a good driver, and I never drive far from A: You may be an excellent driver, but if you’re in an accident -- even one that isn’t your fault -- you and your passengers can be hurt. Being a good driver doesn’t protect you from things beyond your control, such as bad drivers. Most accidents occur within 25 miles (40 km) of home. And the greatest number of serious injuries and deaths occur at speeds of less than 40 mph (65 km/h). Safety belts are for everyone.

How to Wear Safety Belts Properly Adults This part is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and babies. If a child will be riding in your Oldsmobile, see the part of this manual called “Children.” Follow those rules for everyone’s protection. First, you’ll want to know which restraint systems your vehicle has. We’ll start with the driver position.

Driver Position This part describes the driver’s restraint system. Lap-Shoulder Belt The driver has a lap-shoulder belt. Here’s how to wear it properly. 1, Close and lock the door. 2. Adjust the seat (to see how, see “Seats” in the Index)

so you can sit up straight.

3. Pick up the latch plate and pull the belt across you.

Don’t let it get twisted.

4. Push the latch plate into the buckle until it clicks.

Pull up on the latch plate to make sure it is secure. If the belt isn’t long enough, see “Safety Belt Extender” at the end of this section. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.

1-12

5. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder belt.

low and snug on The lap part of the belt should be worn the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen. This could cause serious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take be.lt restraining forces. The safety belt locks if there’s a sudden stop or a crash.

---1

You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The

fit against your body. shoulder belt

should

What's wrong with this?

A: The shoulder belt is too loose. It won't give nearly

as much protection this way.

1-14

What's wrong with this?

You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you.

A: The belt is buckled in the wrong place.

1-15

Q: What’s wrong with this?

You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which aren’t as strong as shoulder bones. You could also severely injure internal organs like your liver or spleen.

A: The shoulder belt is worn under the arm. It sl~ould

be worn over the shoulder at all times.

1-16

Q: What's wrong with this'!

You can be seriously injured by a twisted belt. In a crash, you wouldn't have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your retailer to fix it.

A: The belt is twisted across the body.

Supplemental Inflatable Restraint (SIR) System This part explains the Supplemental Inflatable Restraint (SIR) system or air bag system. Your Oldsmobile has an air bag for the driver. Here are the most important things to know about the air bag system:

you aren’t wearing your safety belt -- even if you You can be severely injured or killed in a crash if have an air bag. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it. Air bags are “supplemental restraints” to the safety belts. All air bags are designed to work with safety belts, but don’t replace them. Air bags are CAUTION: (Continued)

To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.

1-18

There is an air bag readiness light on the instrument panel, which shows AIR BAG.

AIR BAG

The system checks the air bag electrical system for malfunctions. The light tells you if there is an electrical problem. See (‘Air Bag Readiness Light” in the Index for more information.

designed to work only in moderate to severe crashes where the front of your vehicle hits something. They aren’t designed to inflate at all in rollover, rear, side or low-speed frontal crashes. Everyone in your vehicle should wear a safety belt properly -- whether or not there’s an air bag for that person.

/i\ CAUTION:

Air bags inflate with great force, faster than the blink of an eye. If you’re too close to an inflating air bag, it could seriously injure you. Safety belts help keep you in position before and during a crash. Always wear your safety belt, even with an air bag, and sit as far back as you can while still maintaining control of your vehicle.

1-19

How the Air Bag System Works

A CAUTION:

Don’t attach anything to, or put anything between an occupant and an air bag. If something is between the driver and the air bag, the bag might not inflate properly or it might force the object into you and cause injury. The path of an inflating air bag must be kept clear, so don’t attach or put anything on or near the steering wheel hub.

Where is the air bag? The driver’s air bag is in the middle of the steering wheel.

1-20

When should an air bag inflate? An air bag is designed to inflate in a moderate to severe frontal or near-frontal crash. The air bag will inflate only if the impact speed is above the system’s designed “threshold level.’’ If your vehicle goes straight into a wall that doesn’t move or deform, the threshold level is about 14 to 18 mph (23 to 29 ktdh). The threshold level can vary, however, with specific vehicle design, so that it can be somewhat above or below this range. If your vehicle strikes something that will move or deform, such as a parked car, the threshold level will be higher. The air bag is not designed to inflate in rollovers, side impacts or rear impacts, because inflation would not help the occupant. In any particular crash, no one can say whether an air bag should have inflated simply because of the damage to a vehicle or because of what the repair costs were. Inflation is determined by the angle of the impact and how quickly the vehicle slows down in frontal and near-frontal impacts. The air bag system is designed to work properly under a wide range of conditions, including off-road usage. Observe safe driving speeds, especially on rough terrain. As always, wear your safety belt. See “Off-Road Driving“ in the Index for more tips on off-road driving.

What makes an air bag inflate? In an impact of sufficient severity, the air bag sensing system detects that the vehicle is in a crash. The sensing system triggers a release of gas from the inflator, which inflates the air bag. The inflator, air bag and related hardware are all part of the air bag module inside the steering wheel. How does an air bag restrain? In moderate to severe frontal or near-frontal collisions, even belted occupants can contact the steering wheel. The air bag supplements the protection provided by safety belts. Air bags distribute the force of the impact more evenly over the occupant’s upper body, stopping the occupant more gradually. But air bags would not help you in many types of collisions, including rollovers, rear impacts and side impacts, primarily because an occupant’s motion is not toward the air bag. Air bags should never be regarded as anything more than a supplement to safety belts, and then only in moderate to severe frontal or near-frontal collisions.

What will you see after an air bag inflates‘? After an air bag inflates, it quickly deflates, so quickly that some people may not even realize the air bag inflated. Some components of the air bag module in the steering wheel hub will be hot for a short time. The parts of the bag that come into contact with you may be warm, but not too hot to touch. There will be some smoke and dust coming from vents i n the deflated air bag. Air bag inflation doesn‘t prevent the driver from seeing or from being able to steer the vehicle, nor does it stop people from leaving the vehicle.

When an air bag inflates, there is dust in the air. This dust could cause breathing problems for people with a history of asthma or other breathing trouble. To avoid this, everyone in the vehicle should get out as soon as it is safe tu do so. If you have breathing problenls but can’t get out of the vehicle after an air bag inflates, then get fresh air by opening a window or door.

The air bag is designed to inflate only once. After it inflates. ~011’11 need some new parts for your air bag system. If you don’t get them, the air bag system won‘t be there to help protect you i n another crash. A new system will include the air bag module and possibly other parts. The service manual for your vehicle covers the need to replace other parts. Your vehicle is equipped with a diagnostic module, which records information about the air bag system. The module records information about the readiness of the system, when the sensors are activated and driver’s safety belt usage at deployment. Let only qualified technicians work on your air bag system. Improper service can mean that your air bag system won’t work properly. See your retailer for service.

NOTICE:

If you damage the cover for the driver’s air bag, the bag may not work properly. You may have to replace the air bag module. Do not open or break the air bag cover.

1-22

Servicing Your Air Bag-Equipped Oldsmobile The air bag affects how your Oldsmobile should be serviced. There are parts of the air bag system in several places around your vehicle. You don't want the system to inflate while someone is working on your vehicle. Your Oldsmobile retailer and the Bravada Service Manual have information about servicing your vehicle and the air bag system. To purchase a service manual, see "Service and Owner Publications" in the Index.

For up to 10 minutes after the ignition key is turned off and the battery is disconnected, an air bag can still inflate during improper service. You can be in,jured if you are close to an air bag when it inflates. Avoid wires wrapped with yellow tape, or yellow connectors. They are probably part of the air bag system. Be sure to follow proper service procedures, and make sure the person performing work for you is qualified to do so.

The air bag system does not need regular maintenance.

Adding Equipment to Your Air Bag-Equipped Oldsmobile Q.' If I add a push bumper or a bicycle rack to the

front of my vehicle, will it keep the air bag from working properly?

A: As long as the push bumper or bicycle rack is

attached to your vehicle so that the vehicle's basic structure isn't changed, it's not likely to keep the air bag from working properly i n a crash. Is there anything I might add to the front of the vehicle that could keep the air bag from working properly?

A: Yes. If you add things that change your vehicle's

frame, bumper system, front end sheet metal or height, they lnay keep the air bag system from working properly. Also, the air bag system may not work properly if you relocate any of the air- bag sensors. If you have any question about this, you should contact Customer Assistance before you modify your vehicle. (The phone numbers and addresses for Customer Assistance are in Step Two of the Customer Satisfaction Procedure in this manual. See "Customer Satisfaction Procedure" in the Index.)

1-23

Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they don’t wear safety belts.

A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.

1-24

The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly. Right Front Passenger Position The right front passenger’s safety belt works the same way as the driver3 safety belt. See “Driver Position’’ earlier in this section. When the shoulder belt is pulled out all the way, it will lock. If it does, let it go back all the way and start again. Rear Seat Passengers It’s very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who aren’t safety belted can be thrown out of the vehicle in a crash. And they can strike others in the vehicle who are wearing safety belts.

Rear Seat Outside Passenger Positions

Lap-Shoulder Belt The positions next to the windows have lap-shoulder belts. Here’s how to wear one properly.

1. Pick up the latch plate and pull the belt across you.

Don’t let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly.

2. Push the latch plate into the buckle until it clicks. is secure.

Pull up on the latch plate to make sure it When the shoulder belt is pulled out all the way, it will lock. If it does, let it go back all the way and start again.

If the belt is not long enough, see “Safety Belt Extender” at the end of this section. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.

The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen. This could cause serious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.

-. To make the lap part tight, pull down on the buckle end of the belt as you pull up on the shoulder part.

1-26

The safety belt locks if there’s a sudden stop The safety belt also locks if you pull the belt quickly out of the retractor.

or a crash. very

~~

CAUTION:

You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your body.

To unlatch the belt, just push the button on the buckle.

1-27

Rear Safety Belt Comfort Guides for Children and Small Adults Rear shoulder belt comfort guides will provide added safety belt comfort for children who have outgrown child restraints and for small adults. When installed on a shoulder belt, the comfort guide pulls the belt away from the neck and head. There is one guide for each outside passenger position in the rear seat. To provide added safety belt comfort for children who have outgrown child restraints and for smaller adults, the comfort guides may be installed on the shoulder belts. Here’s how to install a comfort guide and use the safety belt:

1-28

1. Pull the elastic cord out from between the edge of the seatback and the interior body to remove the guide from its storage clip.

2 . Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt, and insert the two edges of the belt into the slots of the guide.

3. Be sure that the belt is not twisted and it lies flat.

The elastic cord must be under the belt and the guide on top.

Center Rear Passenger Position

4. Buckle, position and release the safety belt as

described in "Rear Seat Outside Passenger Positions" earlier in this section. Make sure that the shoulder belt crosses the shoulder.

To remove and store the comfort guides, squeeze the belt edges together so that yo11 can take them out from the guides. Pull the guide upward to expose its storage clip, and then slide the guide onto the clip. Rotate the guide and clip inward and in between the seatback and the interior body, leaving only the loop of elastic cord exposed.

Lap Belt

When you sit in the center rear seating position, you have a lap safety belt which has a retractor. 1. Pick up the latch plate and pull the belt across you.

Don’t let it get twisted.

2. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure.

3. Feed the lap belt into the retractor to tighten it.

4. Position and release it the same way as the lap part

of a lap-shoulder belt. If the belt isn’t long enough, see “Safety Belt Extender” at the end of this section. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.

Children Everyone in a vehicle needs protection! That includes infants and all children smaller than adult size. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle. Smaller Children and Babies

’ A CAUTION:

Smaller children and babies should always be restrained in a child or infant restraint. The instructions for the restraint will say whether it is the right type and size for your child.

CAUTION: (Continued)

A very young child’s hip bones are so small that a regular belt might not stay low on the hips, as it should. Instead, the belt will likely be over the child’s abdomen. In a crash, the belt would apply force right on the child’s abdomen, which could cause serious or fatal injuries. So, be sure that any child small enough for one is always properly restrained in a child or infant restraint.

1-32

heavy you can’t hold it. For example, in a crash at only 25 mph (40 km/h), a 12-lb. (5.5 kg) baby will suddenly become a 240-lb. (110 kg) force on your arms. The baby would be almost impossible to hold. Secure the baby in an infant restraint.

vehicle. A baby doesn’t weigh much -- until a Never hold a baby in your arms while riding in a crash. During a crash a baby will become so

CAUTION: (Continued)

1-33

Child Restraints Be sure the child restraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets Federal Motor Vehicle Safety Standards. Then follow the instructions for the restraint. You may find these instructions on the restraint itself or in a booklet, or both. These restraints use the belt system in your vehicle, but the child also has to be secured within the restraint to help reduce the chance of personal injury. The instructions that come with the infant or child restraint will show you how to do that.

Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We at General Motors therefore recommend that you put your child restraint in a rear seat outside position unless the child is an infant and you’re the only adult in the vehicle. In that case, you might want to secure the restraint in the right front seat where you can keep an eye on the baby. Wherever you install it, be sure to secure the child restraint properly. Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle. Be sure to properly secure any child restraint in your vehicle -- even when no child is in it.

1-34

Top Strap

If your child restraint has a top strap, anchored. Anchor brackets for the rear outside seat positions are located on the floor in the cargo area.

it should be

Don't use the front set of tie-down brackets. Anchor the top strap to the rearmost bracket on vehicle as the child restraint. Once you have the top strap anchored, you'll be ready to secure the child restraint itself.

the same side of the

1-35

Securing a Child Restraint in a Rear Outside Seat Position

2.

3.

You’ll be using the lap-shoulder belt. See the earlier part about the top strap if the child restraint has one. 1.

Put the restraint on the seat. Follow the instructions for the child restraint. Secure the child in the child restraint as the instructions say. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. If the shoulder belt goes in front of the child’s face or neck, put it behind the child restraint.

1-36

4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.

5. Pull the rest of the shoulder belt all the way out of

the retractor to set the lock.

6. To tighten the belt, feed the shoulder belt back into the

retractor while you push down on the child restraint.

7. Push and pull the child restraint in different

directions to be sure it is secure.

To remove the child restraint, just unbuckle the vehicle’s safety belt and let it go back all the way. The safety belt will move freely again and be ready to work for an adult or larger child passenger.

1-37

I Center Seat Position

Securing a Child Restraint in the Right Front Seat Position

Oon’t use child restraints in these positions. The restraints won’t work properly.

You’ll be using the lap-shoulder belt. See the earlier part about the top strap if the child restraint has one. 1. Put the restraint on the seat. Follow the instructions

for the child restraint.

2. Secure the child in the child restraint as the

instructions say.

3. Pick up the latch plate, and run the lap and shoulder

portions of the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. If the shoulder belt goes in front of the child’s face or neck, put it behind the child restraint.

4. Buckle the belt. Make sure the release button is

positioned so you would be able to unbuckle the safety belt quickly if you ever had to.

5. Pull the rest of the shoulder belt all the way out of

the retractor to set the lock.

1-39

7. Push and pull the child restraint in different

directions to be sure it is secure. Adjust the bucket seat forward until the lap portion of the safety belt holds the restraint firmly. But don’t move it any more than needed to tighten the lap belt.

To remove the child restraint, just unbuckle the vehicle’s safety belt and let it go back all the way. The safety belt will move freely again and be ready to work for an adult or larger child passenger.

6. To tighten the belt, feed the shoulder belt back into the

retractor while you push down on the child restraint.

1-40

Larger Children

Accident statistics show that children are safer if they are restrained in the rear seat. But they need to use the safety belts properly. 0 Children who aren’t buckled

up can be thrown out in

a crash.

0 Children who aren’t buckled

people who are.

up can strike other

Children who have outgrown child restraints should wear the vehicle’s safety belts. If you have the choice, a child should sit next to a window so the child can wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.

1-41

Never do this. Here two children are wearing the same belt. The belt can’t properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. Q:

What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? Move the child toward the center of the vehicle, but be sure that the shoulder belt still is on the child’s shoulder, so that in a crash the child’s upper body would have the restraint that belts provide. If the child is sitting in a rear seat outside position, see “Rear Safety Belt Comfort Guides” in the Index. If the child is so small that the shoulder belt is still very close to the child’s face or neck, you might want to place the child in a seat that has a lap belt, if your vehicle has one.

A:

1-42

A CAUTION:

Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt. The belt’s force would then be applied right on the child’s abdomen. That could cause serious or fatal injuries.

Wherever the child sits, the lap portion of the belt should be worn low and snug on the hips, just touching the child’s thighs. This applies belt force to the child’s pelvic bones in a crash.

1-43

Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt isn’t long enough to fasten, your retailer will order you an extender. It’s free. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you. The extender will be just for you, and just for the seat in your vehicle that you choose. Don’t let someone else use it, and use it only for the seat it is made to fit. To wear it, just attach it to the regular safety belt.

Checking Your Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. Torn or frayed safety belts may not protect you in a crash. They can rip apart under impact forces. If a belt is torn or frayed, get a new one right away. Also look for any opened or broken air bag covers, and have them repaired or replaced. (The air bag system does not need regular maintenance.)

1-44

Replacing Restraint System Parts After a Crash If you’ve had a crash, do you need new belts? After a very minor collision, nothing may be necessary. But if the belts were stretched, as they w o ~ ~ l d be if worn during a more severe crash, then you need new belts.

If you ever see a label on the driver’s safety belt buckle that says to replace the buckle assembly, be sure to do so. Then the new buckle assernbly will be there to help protect you in a collision. If belts are cut or damaged, replace them. Collision damage also may mean you will need to have safety belt or seat parts repaired or replaced. New parts and repairs may be necessary even if the belt wasn’t being used at the time of the collision. If an air bag inflates, you’ll need to replace air bag system parts. See the part on the air bag system earlier in this section.

ATTENTION 1

CAUTION

injury. buckle assembly must be replaced. See Owner’s Manual Pour aider ?I &iter les blessures corporelles. la boucle doit &re remplac6e. Voir le Gutde du conducteur. Printed in U.S.A.

1-46

a

Section 2 Features and Controls

Here you can learn about the many standard and optional features on your Oldsnwbile, and information on starting, shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is working properly -- and what t o do if you have a problem.

2-2 2 -4 2-5 2-6 2-7 2- I O 2-1 1 2- 12 2-13 2- 14 2-15 2-18 2-22 2-34

Important Information About Keys Door Locks Operation of Child Security Locks Remote Keyless Entry Battery Replacement for RKE Preventing Theft of Your Vehicle New Vehicle "Break-In" Ignition Positions Tips on Starting Your Engine Using the Engine Coolant Heater Automatic Transmission Operation Parking Brake Guidelines Important Information on Engine Exhaust Operation of Your Windows

2-2s 2-25 2-26

2-27 2-28 2-3 1 2-32 2-33 2-34 2-35 2-48 2-52

Adjusting the Tilt Steering Wheel Functions of the Multifunction Lever How to Use the HighLow Beam Headlamp Changer Windshield Wipers and Fluid Using Cruise Control Exterior Lamps Daytime Running Lamps (DRL) Interior Lamps Rearview Mirrors Storage Compartments Instrument Panel Overview All About Your Warning Lights and Gages

Keys A CAUTION:

Leaving young children in a vehicle with the ignition key is dangerous for many reasons. A child or others could be badly injured or even killed. They could operate power windows or other controls or even make the vehicle move. Don't leave the keys in a vehicle with young children.

2-2

This vehicle has one double-sided key for the ignition, liftgate and door locks. It will fit with either side up.

NOTICE:

Your vehicle has a number of new features that can help prevent theft. But you can have a lot of trouble getting into your vehicle if you ever lock your keys inside. You may even have to damage your vehicle to get in. So be sure you have extra keys.

When a new vehicle is delivered, the retailer provides the owner with a pair of identical keys and a key code number. The key code number tells your retailer or a qualified locksmith how to make extra keys. Keep this number in a safe place. If you lose your keys, you’ll be able to have new ones made easily using this number. Your selling dealer should also have this number.

2-3

1 Door Locks

Unlocked doors can be dangerous. Passengers -- especially children -- can easily open the doors and fall out. When a door is locked, the inside handle won’t open it. Outsiders can easily enter through an unlocked door when you slow down or stop your vehicle. This may not be so obvious: You increase the chance of being thrown out of the vehicle in a crash if the doors aren’t locked. Wear safety belts properly, lock your doors, and you will be far better off whenever you drive your vehicle.

There are several ways to lock and unlock your vehicle. You can use your key to unlock your door from the outside. To lock your door from the inside, slide the lever on your inside door rearward.

To unlock the door, slide the lever on your inside door forward. You will see a red area on the lever.

2-4

Power Door Locks

Rear Door Security Lock

*+ ;~.*. The power door lock switch

is located on the armrest. Press LOCK to lock all the doors at once.

With this feature, you can lock the rear doors so they can’t be opened from the inside by passengers. Move the lock up to lock the doors and down to release the door locks.

To unlock the doors, press the raised area next to the key symbol. The lever on each rear door works only that door’s lock.

Leaving Your Vehicle If you are leaving the vehicle, take your key, open your door and set the locks from inside. Then get out and close the door.

2-5

Keyless Entry System You can lock and unlock your doors or unlock your liftgate from up to 30 feet (9 m) away using the key chain transmitter supplied with your vehicle. Your Keyless Entry System operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry and Science Canada Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with RSS-210 of Industry and Science Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. The range of this system is about 30 feet (9 m). At times you may notice a decrease in range. This is normal for any remote lock control system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this:

2-6

Check to determine if battery replacement or resynchronization is necessary. See the instructions that follow. Check the distance. You may be too far from your vehicle. You may need to stand closer during rainy or snowy weather. Check the location. Other vehicles or objects may be blocking the signal. Take a few steps to the left OS right. If you’re still having trouble, see your Oldsmobile retailer or a qualified technician for service.

Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment. Operation When you press UNLOCK, the driver’s door and liftgate will unlock automatically. If you press UNLOCK again within five seconds, all the doors will unlock. Press LOCK to lock all the doors. Press the REAR button twice within 3 1/2 seconds to unlock and unlatch the liftgate. The transmission must be in PARK (P) or NEUTRAL (N).

Matching Transmitter(s) To Your Vehicle Each key chain transmitter is coded to prevent another transmitter from unlocking your vehicle. If a transmitter is lost or stolen, a replacement can be purchased through your retailer. Remember to bring any remaining transmitters with you when you go to your retailer. When the retailer matches the replacement transmitter to your vehicle, any remaining transmitters must also be matched. Once your retailer has coded the new transmitter, the lost transmitter will not unlock your vehicle. Each vehicle can have only two tr'msmitters matched to it. Battery Replacement Under normal use, the battery in your key chain transmitter should last about two years. You can tell the battery is weak if the transmitter won't work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it's probably time to change the battery.

NOTICE:

To replace the battery in the Keyless Entry transmitter:

1. Insert a dime in the slot between the covers of the

transmitter housing near the key ring hole. Remove the bottom by twisting the dime.

2. Remove and replace the battery with a three volt

CR2032 or equivalent battery, positive (+) side down.

3. Align the covers and snap them together. 4. Check the operation of the transmitter.

When replacing the battery, use care not to touch any of the circuitry. Static from your body transferred to these surfaces may damage the transmitter.

2-7

Resynchronization Resynchronization may be necessary due to the security method used by this system. The transmitter does not send the same signal twice to the receiver. The receiver will not respond to a signal it has been sent previously. This prevents anyone from recording and playing back the signal from the transmitter. To resynchronize your transmitter, stand close to your vehicle and simultaneously press and hold the LOCK and UNLOCK buttons on the transmitter for not more than five seconds. The door locks should cycle to confirm synchronization. If the locks do not cycle, see your retailer for service.

Liftgate

It can be dangerous to drive with the rear window or liftgate open because carbon monoxide (CO) gas can come into your vehicle. You can’t see or smell CO. It can cause unconsciousness and even death. If you must drive with the rear window or liftgate open or if electrical wiring or other cable connections must pass through the seal between the body and the rear window or liftgate: 0 Make sure all windows are shut. 0 Turn the fan on your heating or cooling

system to its highest speed with the setting on VENT. That will force outside air into your vehicle. See “Comfort Controls” in the Index.

0 If you have air outlets on or under the instrument panel, open them all the way.

2-8

See “Engine Exhaust” in the Index.

Liftgate Release There are several ways to release the liftgate. However, the liftgate will not release if the vehicle is in gear. You can use you key to unlock the liftgate from the outside. Insert the key into the liftgate lock button and turn it counterclockwise. All doors will unlock. You may also use the Keyless Entry system described earlier. The liftgate can be opened without a key if the driver’s door is unlocked.

To open the liftgate glass only, unlock the liftgate and press the button.

To open the entire liftgate, unlock the liftgate and lift the handle located in the center of the door. The liftgate and glass will automatically lock when shut. To lock the power lock system from the outside, insert the key in the lock button and turn it clockwise. All doors will lock.

2-9

Xemote Liftgate Glass Release

This button on the driver’s side of the steering column allows you to release the liftgate glass from inside the vehicle.

four shift lever must be in PARK (P) or NEUTRAL (N) or the release to work.

Theft Vehicle theft is big business, especially in some cities. Although your Oldsmobile has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. However, there are ways you can help. Key in the Ignition If you leave your vehicle with the keys inside, it’s an easy target for joy riders or professional thieves -- so don’t do it. When you park your Oldsmobile and open the driver’s door, you’ll hear a tone reminding you to remove your key from the ignition and take it with you. Always do this. Your steering wheel will be locked, and so will your ignition and transmission. And remember to lock the doors.

2-10

Parking at Night Park in a lighted spot, close all windows and lock your vehicle. Remember to keep your valuables out of sight. Put them in a storage area, or take them with you. Parking Lots If you park in a lot where someone will be watching your vehicle, it’s best to lock it up and take your keys. But what if you have to leave your ignition key? What if you have to leave something valuable in your vehicle?

Put your valuables in a storage area, like your glove box.

0 Lock all the doors except the driver’s.

New Vehicle “Break-In” NOTICE: Your modern Oldsmobile doesn’t need an elaborate “break-in.’’ But it will perform better in the long run if you follow these guidelines: Keep your speed at 55 mph (88 kmk) or Don’t drive at any one speed -- fast or less for the first 500 miles (805 km). slow -- for the first 500 miles (805 km).

Don’t make full-throttle starts. Avoid making hard stops for the first 200 miles (322 km) or so. During this time your new brake linings aren’t yet broken in. Hard stops with new linings can mean premature wear and earlier replacement. Follow this breaking-in guideline every time you get new brake linings. Don’t tow a trailer during break-in. See “Towing a Trailer” in the Index for more information.

2-11

I NOTICE:

Don’t operate accessories in the ACCESSORY position for long periods of time. Prolonged operation of accessories in the ACCESSORY position could drain your battery and prevent you from starting your vehicle.

LOCK (B): This position locks your ignition, steering wheel and transmission. It’s a theft-deterrent feature. You will only be able to remove your key when the ignition is turned to LOCK. OFF (C): This position lets you turn off the engine but still turn the steering wheel. Use OFF if you must have your vehicle in motion while the engine is off (for example, if your vehicle is being towed). RUN (D): This is the position for driving. START (E): This starts your engine.

Ignition Positions Use the key to turn the ignition switch to five different positions.

A L E

ACCESSORY (A): ACCESSORY lets you use things like the radio and the windshield wipers when the engine is off. Push in the key and turn it toward you. Your steering wheel will remain locked, just as it was before you inserted the key.

2-12

NOTICE:

If your key seems stuck in LOCK and you can’t turn it, be sure you are using the correct key; if so, is it all the way in? If it is, then turn the steering wheel left and right while you turn the key hard. But turn the key only with your hand. Using a tool to force it could break the key or the ignition switch. If none of this works, then your vehicle needs service.

Starti 3 Your Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine won’t start i n any other position -- that’s a safety feature. To restart when you’re already moving, use NEUTRAL, (N j only.

NOTICE:

Don’t try to shift to PARK (P) if your Oldsmobile is moving. If you do, you could damage the transmission. Shift to PARK (P) only when your vehicle is stopped.

1. Without pushing the accelerator pedal, turn your

ignition key to START. When the engine starts. let go of the key. The idle speed w i l l go down as your engine gets warm.

NOTICE:

Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. And the excessive heat can damage your starter motor.

2-13

Engine Coolant Heater (Option)

The engine coolant heater cord is secured on the driver’s side of the vehicle, by the brake controller.

.. .

In very cold weather, 0°F (- 18 “C) or colder, the engine coolant heater can help. You’ll get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.

If it doesn’t start right away, hold your key in START. If it doesn’t start in 10 seconds, push the accelerator pedal all the way down for five more seconds, or until it starts. If your engine still won’t start (or starts but then stops), wait 15 seconds and start over. When the engine starts, let go of the key and the accelerator pedal.

3.

NOTICE:

Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your retailer. If you don’t, your engine might not perform properly. If you ever have to have your vehicle towed, see the part of this manual that tells how to do it without damaging your vehicle. See “Towing Your Vehicle” in the Index.

2-14

To Use the Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. 3. Plug it into a normal, grounded 1 10-volt AC outlet.

[ON:

Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet. If the cord won’t reach, use a heavy-duty three-prong extension cord rated for at least 15 amps.

How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your Oldsrnobile retailer in the area where you’ll be parking your vehicle. The retailer can give you the best advice for that particular area. Automatic Transmission Operation There are several different positions for your shift lever.

03

4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away fi-om moving engine parts. If you don’t, it could be damaged.

PARK (P): This locks your rear wheels. It’s the best position to use when you start your engine because your vehicle can’t move easily.

2-15

It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. is Don’t leave your vehicle when the engine running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle won’t move, even when you’re on fairly level ground, always set your parking brake and move the shift lever to PARK (P). Your vehicle will be free to roll -- even if your shift lever is in PARK (P) -- if your transfer case is in a drive gear -- not in NEUTRAL (N). See is in NEUTRAL (N). So, be sure the transfer case “Shifting Into PARK (P)” in the Index. If you’re pulling a trailer, see “Towing a Trailer” in the Index.

Ensure the shift lever is fully in PARK (P) range before starting the engine. Your vehicle has a brake-transmission shift interlock. You have to fully apply your regular brakes before you can shift from PARK (P) when the ignition key is in the RUN position. If you cannot shift out of PARK (P), ease pressure on the shift lever -- press the button on the shift lever and push the shift lever all the way into PARK (P) as you maintain brake application. Then move the shift lever into the gear you wish. See “Shifting Out of PARK (P)” in the Index. REVERSE (R): Use this gear to back up.

NOTICE:

Shifting to REVERSE (R) while your vehicle is moving forward could damage your transmission. Shift to REVERSE (R) only after your vehicle is stopped.

To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transmission, see “Stuck: In Sand, Mud, Ice or Snow” in the Index.

NEUTRAL (N): In this position, your engine doesn’t connect with the wheels. To restart when Y O L I ’ I - ~ already moving, use NEUTRAL (N) only.

AUTOMATIC OVERDRIVE (@): This position is for normal driving. If you need 111o1-e power for passing, and you’re:

Shifting out of PARK (P) or NEUTRAL (N) while your engine is “racing” (running at high speed) is dangerous. Unless your foot is firmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Don’t shift out of PARK (P) or NEUTRAL (N) while your engine is racing.

I NOTICE:

Damage to your transmission caused by shifting out of PARK (P) or NEUTRAL (N) with the engine racing isn’t covered by your warranty.

Going less than about 35 rnph (56 k i d h j , push your accelerator peclal about halfway down. Going about 35 mph (56 k d h j or more, push the accelerator all the way down.

You’ll shift down t o the next gear and have more power. AUTOMATIC OVERDRIVE (0) should not be used when towing a trailer, carrying a heavy load, driving on steep hills 01- for off-road driving. Select THIRD (3) when operating the vehicle under any of these conditions. THIRD (3): This position is also used for normal driving, however it offers more power but lower fuel economy than AUTOMATIC OVERDRIVE (@I. You should L I S ~ THIRD (3) when towing ;I trailer, carrying a heavy load, driving on steep hills or winding roads or for off-road driving. SECOND (2): This position gives you more power but lower fuel economy. You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, b u t then you would also want t o use your txakes off’ and on.

You can also use SECOND (2) for starting your vehicle from a stop on slippery road surfaces. FIRST (1): This position gives you even more power (but lower fuel economy) than SECOND (2). You can use it on very steep hills, or in deep snow or mud. If the selector lever is put in FIRST (1) while the vehicle is moving forward, the transmission won’t shift into FIRST (1) until the vehicle is going slowly enough.

NOTICE:

If your rear wheels can’t rotate, don’t try to drive. This might happen if you were stuck in very deep sand or mud or were up against a solid object. You could damage your transmission. Also, if you stop when going uphill, don’t hold your vehicle there with only the accelerator pedal. This could overheat and damage the transmission. Use your brakes or shift into PARK (P) to hold your vehicle in position on a hill.

Locking Rear Axle Your rear axle can give you additional traction on snow, mud, ice, sand or gravel. It works like a standard axle most of the time, but when one of the rear wheels has no traction and the other does, the locking feature will allow the wheel with traction to move the vehicle. All-Wheel Drive Your engine’s driving power is sent to all four wheels for extra traction. All-wheel drive is like four-wheel drive, but there is no lever or switch to engage or disengage the front axle. It is fully automatic and adjusts itself as needed for road conditions. Parking Brake To set the parking brake, hold the regular brake pedal down with your right foot. Push down the parking brake pedal with your left foot. If the ignition is on, the brake system warning light will come on. To release the parking brake, hold the regular brake pedal down.

2-18

Shifting Into PARK (P)

instrument panel.

NOTICE:

Driving with the parking brake on can cause your rear brakes to overheat. You may have to replace them, and you could also damage other parts of your vehicle.

If you are towing a trailer and you must park on a hill, see ”Towing a Trailer” in the Index. That section shows what to do first to keep the trailer from moving.

It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle won’t move, even when you’re on fairly level ground, use the steps that follow. If you’re pulling a trailer, see “Towing a Trailer” in the Index.

I . Hold the brake pedal down with your right foot and

set the parking brake.

2-19

2. hlove the shift lever into PARK (P) position like this:

Leaving Your Vehicle With the Engine Running

It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake firmly set. And, leave the vehicle with the engine running, it could overheat and even catch fire. You or others could be injured. Don’t leave your vehicle with the engine running unless you have to.

if you

0 Hold in the button on the

lever.

Push the lever a l l the way toward the front of the vehicle.

3. TLIIII the ignition key t o LOCK. 4. Remove the key and take it with YOLI. If you can

remove the key and leave your vehicle, your vehicle is in PARK (P).

If you have to leave your vehicle. with the engine running, be s111-e t o firndy set your parking brake and shifi into PARK (P) before you leave it. After you’ve n~oved the shift lever into the PARK (P) position, hold the reg~~lar brake pedal c k w n . Then, see if you can move the shift lever away from PARK (P) without first pulling it toward you. If you can, it means that the shift lever wasn’t FLIIIY locked into PARK (P).

2-20

Torque Lock If you are parking on a hill and you don’t shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may find it difficult to pull the shift lever out of PARK (P). This is called “torque lock.” To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the driver’s seat. To find out how, see “Shifting Into PARK (P)” in the Index. When you are ready t o drive, move the shift lever out of PARK (P) h

Shifting Out of PARK (P) Your vehicle has a brake-transmission shift interlock. You have to fully apply your regular brake before you can shift from PARK (P) when the ignition is in the RUN position. See “Automatic Transmission Operation” in the Index. If you cannot shift out of PARK (P), ease pressure on the shift lever -- push the shift lever a l l the way into PARK (P) as you maintain brake application. Then press the shift lever button and move the shift lever into the gear you want. If you ever hold the brake pedal down but still can’t shift out of PARK (P), try this: 1. Turn the key to OFF. 2. Apply and hold the brake until the end of Step 4. 3. Shift to NEUTRAL(N). 4. Start the vehicle and then shift t o the drive gear

you want.

5. Have the vehicle fixed as soon as you can.

2-21

Parking Over Things That Burn

Engine Exhaust

Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can't see or smell. It can cause unconsciousness and death. You might have exhaust coming in if:

Your exhaust system sounds strange or different. Your vehicle gets rusty underneath. Your vehicle was damaged in a collision. Your vehicle was damaged when driving over high points on the road or over road debris. Repairs weren't done correctly. Your vehicle or exhaust system had been modified improperly.

If you ever suspect exhaust is coming into your vehicle: 0 Drive it only with all the windows down to

blow out any CO; and

0 Have your vehicle fixed immediately.

Things that can burn could touch hot exha1 parts under your vehicle and ignite. Don't park over papers, leaves, dry grass or other things that can 2-22

burn.

Running Your Engine While You’re Parked It’s better not to park with the engine running. But if ever have to, here are SOT

things to know.

Idling the engine with the air system control off could allow dangerous exhaust into your vehicle (see the earlier Caution under “Engine Exhaust”). Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if this can happen is a garage. Exhaust -- with the fan switch is at the highest setting. One place CO -- can come in easily. NEVER park in a

garage with the engine running. Another closed-in place can be a blizzard. (See “Blizzard” in the Index.)

It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Don’t leave your vehicle when the engine is running unless you have to. If you’ve left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle won’t move, even when you’re on fairly level ground, always set your parking brake and move the shift lever to PARK (P).

Follow the proper steps to be sure your vehicle won’t nove. See “Shifting Into PARK (P)” in the Index. If you’re pulling a trailer, see “Towing a Trailer” in :he Index.

Express-Down Window The driver’s window switch has an express-down feature that allows you to lower it without holding the window switch. Hold the driver’s window switch down for more than a half a second to activate the express-clown feature. Lightly tap the switch to open the window slightly. The express-down feature can be interrupted at any time by pressing the up arrow end of the switch.

Lockout Switch Your vehicle has a lockout feature to prevent passengers from operating the power windows. Press LOCK to activate this feature. Press NORM and the windows return to normal operation. Horn To sound the horn, press the center pad on the steering wheel.

Windows Power Windows

These switches on the driver’s door control each of the windows when the ignition is in the RUN position.

There are individual controls on each of the side doors. Press the side of the switch with the down arrow to lower a window. Press the side of the switch with the up arrow to raise a window.

2-24

Tilt Wheel

Turn SignaVMultifunction Lever

You should adjust the steering wheel before you drive.

You can raise it to the highest level to give your legs more room when you enter and exit the vehicle. To tilt the wheel, hold the steering wheel and pull the lever toward you. Move the steering wheel to a comfortable level, then release the lever to lock the wheel in place. Do not adjust the steering wheel while driving.

The lever on the left side of the steering column includes your:

Turn Signal and Lane Change Indicator Headlamp HighLow Beam Changer Windshield Wipers Windshield Washer

0 Cruise Control

2-25

If a bulb is burned out, replace it to help avoid an accident. If the arrows don't go on at all when you signal a turn, check the fuse (see "Fuses and Circuit Breakers" in the Index) and for burned-out bulbs. If you have a trailer towing option with added wiring for the trailer lamps, a different turn signal flasher is used. With this flasher installed, the signal indicator will flash even if a turn signal bulb is burned out. Check the front and rear turn signal lamps regularly to make sure they are working. Headlamp HighLow Beam Changer To change the headlamps from low to high-beam or high to low-beam, pull the multifunction lever all the way toward you. Then release it.

When the high beams are on, this indicator light on the instrument panel will also be on.

Turn and Lane Change Signals The turn signal has two upward (for right) and two downward (for left) positions. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically.

An arrow on the instrument panel will flash in the direction of the turn or lane change.

To signal a lane change, just raise or lower the lever until the arrow starts to flash. Hold it there until you complete your lane change. The lever will return by itself when you release it. As you signal a turn or a lane change, if the arrows don't flash but just stay on, a signal bulb may be burned out and other drivers won't see your turn signal.

2-26

Windshield Wipers

For steady wiping at low speed, turn the band away from you to the LOW position. For high-speed wiping, turn the band further, to HIGH. To stop the wipers, move the band to the OFF position. Be sure to clear ice and snow from the wiper blades before using them. If they‘re frozen to the windshield, carefully loosen or thaw them. If your blades do become worn or damaged, get new blades or blade inserts. Windshield Washer At the top of the multifunction lever, there’s a paddle marked with the windshield washer symbol and PUSH. To spray washer fluid on the windshield, press the paddle. The wipers will clear the window and then either stop or return to your preset speed.

You control the windshield wipers by turning the band with the wiper symbol on it. For a single wiping cycle, turn the band to MIST. Hold it there until the wipers start, then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on MIST longer. You can set the wiper speed for a long or short delay between wipes. This can be very useful in light rain or snow. Turn the band to choose the delay time. The closer to LOW, the shorter the delay.

In freezing weather, don’t use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.

I I .

Rear Window Washermiper

WASH

REAR WIPER

This switch is located on the instrument panel. The rear window wiper operates with a constant five second delay when the rear wiper switch is in the ON position. If the rear glass is opened, the wiper arm will automatically park on the iiftgate. When the glass is completely closed, the wiper will resume the delay mode.

2-28

To wash the window, press and hold ON. The wipers will continue to work after YOLI release the switch, Press OFF to turn the wiper off. The rear window washer uses the same fluid bottle as the windshield washer. However, the rear window washer will run out of fluid before the windshield washer. If you can wash your windshield but not your rear window, check your fluid level. Cruise Control

really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h).

. . .:. ,..< ,~-:,~:,-l

If you apply your brakes, the cruise control will shut off.

A CAUTIO .:

Cruise control can be dangerous where you can’t drive safely at a steady speed. So, don’t use your cruise control on winding roads or in heavy traffic. Cruise control can be dangerous on slippery roads. On such roads, fast changes in tire traction can cause needless wheel