Login- Download PDF Manual
-
FUEL-FILLER CAP
WARNING
● Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.
● Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.
● Use only an original equipment type fuel-filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emis- sion control system. An incorrect cap can result in a serious malfunction and possible injury. It could also cause Malfunction Indicator Light the (MIL) to come on.
● Never pour fuel into the throttle body to
attempt to start your vehicle.
3-26 Pre-driving checks and adjustments
● Do not fill a portable fuel container in the vehicle or trailer. Static electricity can cause an explosion of flammable liquid, vapor or gas in any vehicle or trailer. To reduce the risk of serious injury or death when filling portable fuel containers: – Always place the container on the
ground when filling.
– Do not use electronic devices when
filling.
– Keep the pump nozzle in contact with the container while you are fill- ing it.
– Use only approved portable fuel con-
tainers for flammable liquid.
CAUTION
● Do not use E-15 or E-85 fuel in your vehicle. For further information see the “Fuel Recommendation” in the “Techni- cal and consumer information” section of this manual.
● Failure to tighten the fuel-filler cap Malfunc- properly may cause the tion Indicator Light (MIL) to illuminate. light illuminates because If the the fuel-filler cap is loose or missing, tighten or install the cap and continue light to drive the vehicle. The should turn off after a few driving trips. light does not turn off after a If the few driving trips, have the vehicle in- spected by a NISSAN dealer.
● The LOOSE FUEL CAP warning mes- sage will display if the fuel-filler cap is not properly tightened. It may take a few driving trips for the message to be displayed. Failure to tighten the fuel- filler cap properly after the LOOSE FUEL CAP warning message is dis- Malfunc- played may cause the tion Indicator Light (MIL) to illuminate. information, see the “Malfunction Indicator Light (MIL)” in the “Instruments and Controls” section in this manual.
● For additional
● If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.
SPA1755
To remove the fuel-filler cap: 1. Turn the fuel-filler cap counterclockwise 䊊1
to remove.
2. Loop the tether strap around the hook while
refueling.
To install the fuel-filler cap: 1.
Insert the fuel-filler cap straight into the fuel- filler tube.
2. Turn the fuel-filler cap clockwise 䊊2 until a
single click is heard.
Pre-driving checks and adjustments 3-27
3. Press the loose fuel cap warning reset but- ton 䊊A in the meter for about 1 second to turn off the LOOSE FUEL CAP warning message after tightening the fuel-filler cap.
Type A
Type B
LPD2126
LPD2025
Loose Fuel Cap warning message The LOOSE FUEL CAP warning message dis- plays in the odometer when the fuel-filler cap is not tightened correctly after the vehicle has been refueled. It may take a few driving trips for the message to be displayed. To turn off the warning message, perform the following: 1. Remove and install the fuel-filler cap as pre-
viously described as soon as possible. 2. Tighten the fuel-filler cap until it clicks.
3-28 Pre-driving checks and adjustments
STEERING WHEEL
SUN VISORS
䊊3 Slide the extension sun visor in or out as
needed.
CAUTION
● Do not store the sun visor before return- ing the extension to its original position.
● Do not pull the extension sun visor
forcedly downward.
LPD0355
TILT OPERATION Push the lock lever 䊊1 down and adjust the steering wheel up or down 䊊2 to the desired position. Pull the lock lever 䊊1 up to lock the steering wheel in place.
WARNING
Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.
WPD0315
䊊1 To block glare from the front, swing down thesun visor.
䊊2 To block glare from the side, remove the sun visor from the center mount and swing the visor to the side.
Pre-driving checks and adjustments 3-29
MIRRORS
SPA1733
LPD2033
WPD0126
VANITY MIRROR (if so equipped) To access the vanity mirror, pull the sun visor down and flip open the mirror cover.
CARD HOLDER (driver’s side only) To access the card holder, pull the sun visor down and slide card in the card holder 䊊A . Do not view information while operating the vehicle.
REARVIEW MIRROR The night position 䊊1 reduces glare from the headlights of vehicles behind you at night. Use the day position 䊊2 when driving in daylight hours.
WARNING
Use the night position only when neces- sary, because it reduces rear view clarity.
3-30 Pre-driving checks and adjustments
OUTSIDE MIRRORS
WARNING
● Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.
● Do not adjust the mirrors while driving. You could lose control of your vehicle and cause an accident.
LPD2168
LPD0237
Manual control type (if so equipped) The outside mirror can be moved in any direction for a better rear view by adjusting the inside lever.
Electric control type (if so equipped) The outside mirror remote control will operate only when the ignition switch is placed in the ACC or ON position. Move the small switch 䊊1 to select the right or left mirror. Adjust each mirror to the desired position using the large switch 䊊2 .
Pre-driving checks and adjustments 3-31
MPA0008
Manual folding outside mirrors Pull the outside mirror toward the door to fold it. Heated mirrors (Canada only) Some outside mirrors can be heated to defrost, defog, or de-ice for improved visibility. Push the rear window defroster switch to activate the heat- ing function. Push the switch again to deactivate, or the heating function will automatically turn off after approximately 15 minutes.
3-32 Pre-driving checks and adjustments
MEMO
Pre-driving checks and adjustments 3-33
4 Monitor, climate, audio, phone and voice recognition systems
Control panel buttons — color screen with Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . 4-2
How to use the touch screen . . . . . . . . . . . . . . . . . . . . 4-3
How to use the BACK button . . . . . . . . . . . . . . . . . . . . 4-5
How to use the MENU button . . . . . . . . . . . . . . . . . . . . 4-5
button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
RearView Monitor (if so equipped). . . . . . . . . . . . . . . . . . . 4-9
How to read the displayed lines . . . . . . . . . . . . . . . . . 4-10
Difference between predicted and actual distances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Adjusting the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Operating tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Heater and Air Conditioner (manual) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Heater operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17
Air conditioner operation (if so equipped) . . . . . . . . 4-18
Air flow charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Servicing air conditioner (if so equipped) . . . . . . . . . . . . 4-23
Audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
FM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23AM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
Satellite radio reception (if so equipped) . . . . . . . . . 4-24
Audio operation precautions . . . . . . . . . . . . . . . . . . . . 4-24
FM/AM radio with compact disc (CD) player (Type A) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . 4-31
FM/AM radio with compact disc (CD) player (Type B) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . 4-34
FM/AM/SAT radio with compact disc (CD) player (Type A) (if so equipped) . . . . . . . . . . . . . . . . . 4-39
FM/AM/SAT radio with compact disc (CD) player (Type B) (if so equipped) . . . . . . . . . . . . . . . . . 4-44
USB interface (models without Navigation System) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . 4-51
USB interface (models with Navigation System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-52
iPod®* player operation without Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . 4-54
iPod®* player operation with Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . 4-57
Bluetooth® streaming audio without Navigation System (if so equipped) . . . . . . . . . . . . . . 4-60
Bluetooth® streaming audio with Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . 4-62
Pandora® audio (if so equipped) . . . . . . . . . . . . . . . . 4-63CD care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65
Steering wheel switch for audio control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-66
Car phone or CB radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-67
Bluetooth® Hands-Free Phone System without Navigation System (if so equipped) . . . . . . . . . . . . . . . . . 4-68
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . 4-69
Using the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-70
Control buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-72
Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-72
List of voice commands . . . . . . . . . . . . . . . . . . . . . . . . 4-74
Voice Adaptation (VA) mode . . . . . . . . . . . . . . . . . . . . 4-78
Manual control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-80
Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . 4-81Bluetooth® Hands-Free Phone System with Navigation System (if so equipped) . . . . . . . . . . . . . . . . . 4-82
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . 4-83
Voice commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-84
Connecting procedure . . . . . . . . . . . . . . . . . . . . . . . . . 4-84Vehicle phonebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-85
Making a call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-86
Receiving a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-87
During a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-87
Ending a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-87
Text messaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-88
Bluetooth settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-89
Phone settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-91NISSAN Voice Recognition System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-92
Using the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-92
System features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-93
Bluetooth® Hands-Free Phone System voice commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-94
Navigation System voice commands . . . . . . . . . . . . . 4-95
Audio system voice commands. . . . . . . . . . . . . . . . . . 4-95
Information voice commands. . . . . . . . . . . . . . . . . . . . 4-96
Help voice commands . . . . . . . . . . . . . . . . . . . . . . . . . 4-96
Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . 4-97CONTROL PANEL BUTTONS — COLOR SCREEN WITH NAVIGATION SYSTEM (if so equipped)
WARNING
● Do not disassemble or modify this sys- tem. If you do, it may result in accidents, fire, or electrical shock.
● In case you notice any foreign object in the system hardware, spill liquid on it, or notice smoke or smell coming from it, stop using the system immediately and contact your nearest NISSAN dealer. Ig- noring such conditions may lead to ac- cidents, fire or electrical shock.
● Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock.
1. Display screen
button**
2. 3. MAP button*
4. NAV button*
LHA2516
5. MENU button
6. BACK button
7. TUNE knob / AUDIO button
8.
(brightness control) button
4-2 Monitor, climate, audio, phone and voice recognition systems
WARNING
● ALWAYS give your full attention to
driving.
● Avoid using vehicle features that could distract you. If distracted, you could lose control of your vehicle and cause an accident.
9. Power button/VOL (volume) control knob
10. CAMERA button
HOW TO USE THE TOUCH SCREEN
* For information regarding the Navigation system control buttons, refer to the separate Navigation System Owner’s Manual.
information regarding the Bluetooth® ** For Hands-Free Phone System control button, see “Bluetooth® Hands-Free Phone System” in this section.
When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will discharge the battery, and the engine will not start.
Reference symbols:
“Example” — Words marked in quotes refer to a key shown only on the display. These keys can be selected by touching the screen.
CAUTION
● The glass display screen may break if it is hit with a hard or sharp object. If the glass screen breaks, do not touch it. Doing so could result in an injury.
● To clean the display, never use a rough cloth, alcohol, benzine, thinner or any kind of solvent or paper towel with a chemical cleaning agent. They will scratch or deteriorate the panel.
● Do not splash any liquid such as water or car fragrance on the display. Contact with liquid will cause the system to malfunction.
To help ensure safe driving, some functions can- not be operated while driving.
The on-screen functions that are not available while driving will be “grayed out” or muted.
Park the vehicle in a safe location and then oper- ate the navigation system.
Monitor, climate, audio, phone and voice recognition systems 4-3
LHA2245
LHA2246
Touch screen operation Selecting the item: Touch an item to select. For example, to select the “Audio” key, touch the “Audio” key 䊊1 on the screen.
Adjusting the item: For screens where an item can be adjusted incre- mentally, such as when adjusting the bass and treble for the audio system, touch the “+” key 䊊1
or the “⫺” key 䊊2 to adjust the settings of an item. When there are more items than can be dis- played on one screen, touch the up arrow 䊊3 to scroll up the page or touch the down arrow 䊊4 to scroll down the page.LHA1478
Other items are adjusted by selecting one of a set number of conditions. For example, the Display Mode can be set to “Automatic”, “Day” or “Night”. To adjust this type of item, touch the item 䊊1 . The item will cycle through the available settings and the red indicator lights to the left of the setting condition 䊊2 will come on or turn off accordingly.4-4 Monitor, climate, audio, phone and voice recognition systems
● OK:
Completes the character input.
Touch screen maintenance If you clean the display screen, use a dry, soft cloth. If additional cleaning is necessary, use a small amount of neutral detergent with a soft cloth. Never spray the screen with water or de- tergent. Dampen the cloth first and then wipe the screen. HOW TO USE THE BACK BUTTON Press the BACK button to return to the previous screen.
LHA2253
HOW TO USE THE MENU BUTTON For more information about the “POIs Powered by Google™”, “Google™ Send-To-Car, “Traffic Information” and “Weather” features, see the separate Navigation System Owner’s Manual. For more information about the “Voice Com- mands” key, see “NISSAN Voice Recognition System” in this section. To select and/or adjust several functions, fea- tures and modes that are available for your ve- hicle: 1. Press the MENU button. 2. Select the “Settings” key.Monitor, climate, audio, phone and voice recognition systems 4-5
LHA2247
Inputting characters: Touch the letter key 䊊1 . There are some options available when inputting characters. ● 123 / ABC:
Changes the available character set to num- bers.
● Space:
Inserts a space.
● Delete:
Deletes the last inputted character with one touch. Touch and hold the “Delete” key to delete all of the characters.
For information regarding Bluetooth® audio, see “Bluetooth® streaming audio with Navigation System” in this section.
LHA2248
3. Select the desired item. Audio For audio setup, refer to “Audio system” in this section. Navigation Refer to the separate Navigation System Own- er’s Manual for information regarding this item. Phone & Bluetooth For information regarding the Bluetooth® Hands-Free Phone System, see “Bluetooth® Hands-Free Phone System” in this section.
4-6 Monitor, climate, audio, phone and voice recognition systems
LHA2249
System Select the “System” key to select and/or adjust various functions of the system. A screen with additional options will appear.
Display Mode The display can be adjusted to fit the level of lighting in the vehicle. Touch the “Display Mode” key to cycle through the options. “Day” and “Night” modes are suited for the respective times of day, while “Automatic” controls the display automatically. Scroll Direction The direction that menus scroll can be adjusted. Choose either “up” or “down”.
LHA1482
Display: Select the “Display” key to adjust the appearance of the display. The following settings can be adjusted: Brightness The brightness of the display can be set to Very Bright, Bright, Default, Dark or Very Dark. Touch the “Brightness” key to cycle through the options.
LHA2250
Clock Settings: Select the “Clock Settings” key to adjust the time and the appearance of the clock on the display. The following settings can be adjusted: Time Format The clock can be set to 12 hours or 24 hours. Date Format Select from five possible formats of displaying the day, month and year.
Monitor, climate, audio, phone and voice recognition systems 4-7
Clock Mode Select the mode for the clock. “Auto” uses the system’s GPS to automatically maintain the time. “Manual” allows you to set the clock using the “Set Clock Manually” key. “Time Zone” maintains the time based upon the zone selected when selecting the “Time Zone” key.
LHA2251
LHA2252
Set Clock Manually When this setting is activated, the clock can be set manually. Touch the “+” or “-” keys to adjust the hours, minutes, day, month and year up or down. “Clock Mode” must be set to “Manual” for this option to be available. Daylight Savings Time When this setting is activated, daylight savings time is on. Touch the “Daylight Savings Time” key to toggle the setting on or off. Time Zone Choose the applicable time zone from the list.
Language:
Select the “Language” key to adjust the language used by the system. The language can be set to English, Français or Español. Touchscreen click:
Select the “Touchscreen Click” key to toggle the touchscreen click feature on or off. When acti- vated, a click sound will be heard every time a key on the screen is touched. System Beeps: Select the “System Beeps” key to toggle the system beep tones feature on or off. When acti- vated, a beep sound will be heard when a pop-up
4-8 Monitor, climate, audio, phone and voice recognition systems
message appears on the screen or a button on the unit (such as the button) is pressed and held for two seconds. Reset all settings/memory: Select the “Reset All Settings/Memory” key to return all settings to default and to clear the memory. Info For information about the “Info” key, see the separate Navigation System Owner’s Manual. XM For XM setup, refer to “Audio system” in this section.
BUTTON
To change the display brightness, press the button. Pressing the button again will change the display to the day or the night display. If no operation is performed within 5 seconds, the display will return to the previous display.
button for more than Press and hold the two seconds to turn the display off. Press the button again to turn the display on.
REARVIEW MONITOR (if so equipped)
When the shift lever is shifted into the R (Re- verse) position, the monitor display shows a rear- ward view from the vehicle.
WARNING
● The system is designed as an aid to the driver in detecting large stationary ob- jects to help avoid damaging the ve- hicle. The system will not detect small objects below the bumper, and may not detect objects close to the bumper or on the ground.
● The RearView Monitor is a convenience but it is not a substitute for proper back- ing. Always turn and check that it is safe to do so before backing up. Always back up slowly.
● Objects viewed in the RearView Moni- tor differ from actual distance because a wide-angle lens is used.
● Make sure that the trunk is securely
closed when backing up.
● Do not put anything on the rearview camera. The rearview camera is in- stalled beside the license plate light.
● When washing the vehicle with high- pressure water, be sure not to spray it around the camera. Otherwise, water may enter the camera unit causing wa- ter condensation on the lens, a mal- function, fire or an electric shock.
● Do not strike the camera. It is a preci- sion instrument. Otherwise, it may mal- function or cause damage resulting in a fire or an electric shock.
CAUTION
There is a plastic cover over the camera. Do not scratch the cover when cleaning dirt or snow from the cover.
Monitor, climate, audio, phone and voice recognition systems 4-9
DIFFERENCE BETWEEN PREDICTED AND ACTUAL DISTANCES The distance guide line and the vehicle width guide line should be used as a reference only when the vehicle is on a level, paved surface. The distance viewed on the monitor is for reference only and may be different than the actual distance between the vehicle and displayed objects.
LHA0437
HOW TO READ THE DISPLAYED LINES Guiding lines which indicate the vehicle width and distances to objects with reference to the vehicle body line 䊊A are displayed on the monitor. Distance guide lines: Indicate distances from the vehicle body. ● Red line 䊊1 : approx. 1.5 ft (0.5 m) ● Yellow line 䊊2 : approx. 3 ft (1 m) ● Green line 䊊3 : approx. 7 ft (2 m) ● Green line 䊊4 : approx. 10 ft (3 m)
LHA2278
The on-screen guidelines can be set to on or off. With the shift lever in the R (Reverse) posi- tion: Press the CAMERA button to toggle the feature on and off. With the shift lever in any position other than the R (Reverse) position: 1. Press the CAMERA button. 2. Select the “Show Guidelines” key to togglethe feature on or off.
4-10 Monitor, climate, audio, phone and voice recognition systems
the hill is the place 䊊B . Note that any object on the hill is further than it appears on the monitor.
WHA1504
Backing up on a steep uphill When backing up the vehicle up a hill, the dis- tance guide lines and the vehicle width guide lines are shown closer than the actual distance. For example, the display shows 3 ft (1.0 m) to the place 䊊A , but the actual 3 ft (1.0 m) distance on
WHA1505
Backing up on a steep downhill When backing up the vehicle down a hill, the distance guide lines and the vehicle width guide lines are shown farther than the actual distance. For example, the display shows 3 ft (1.0 m) to the place 䊊A , but the actual 3 ft (1.0 m) distance on Monitor, climate, audio, phone and voice recognition systems 4-11
the hill is the place 䊊B . Note that any object on the hill is closer than it appears on the monitor.
the position 䊊A if the object projects over the actual backing up course.
WHA1506
Backing up behind a projecting object The position 䊊C is shown farther than the position 䊊B in the display. However, the position 䊊C is actually at the same distance as the position 䊊A . The vehicle may hit the object when backing up to4-12 Monitor, climate, audio, phone and voice recognition systems
4. Adjust the level using the TUNE-SCROLL knob and then press the ENTER/SETTING button to apply the adjustment.
● Do not adjust the Brightness or Contrast of the RearView Monitor while the vehicle is moving.
LHA2254
Without Navigation System
ADJUSTING THE SCREEN The procedure for adjusting the quality of the screen differs depending on the type of screen present on the vehicle.
For vehicles without Navigation System:
1. Press the ENTER/SETTING button.
2. Turn the TUNE-SCROLL knob to highlight
the “Brightness” or “Contrast” key.
3. Press the ENTER/SETTING button.
LHA1482
With Navigation System For vehicles with Navigation System: 1. Press the MENU button. 2. Select the “Settings” key. 3. Select the “System” key. 4. Select the “Display” key. 5. Touch the “Brightness key and adjust the
level to the desired setting.
● Do not adjust the display of the RearView
Monitor while the vehicle is moving.
Monitor, climate, audio, phone and voice recognition systems 4-13
VENTS
Side vents
SAA3126
Adjust the air flow direction of the vents by open- ing, closing or rotating.
OPERATING TIPS
CAUTION
● Do not use alcohol, benzine or thinner to clean the camera. This will cause discoloration. To clean the camera, wipe with a cloth dampened with a di- luted mild cleaning agent and then wipe with a dry cloth.
● Do not damage the camera as the moni-
tor screen may be adversely affected.
● When the shift lever is shifted to R (Re- verse), the monitor screen automatically changes to the RearView Monitor mode. However, the radio can be heard.
● It may take some time until the RearView Monitor is displayed after the shift lever has been shifted to R (Reverse). Objects may be distorted momentarily until the RearView Monitor screen is displayed completely. When the shift lever is returned to a position other than R (Reverse), it may take some time until the screen changes. Objects on the screen may be distorted until they are completely displayed.
● When the temperature is extremely high or low, the screen may not clearly display ob- jects. This is not a malfunction.
● When strong light directly enters the cam-
era, objects may not be displayed clearly.
● Vertical lines may be seen in objects on the screen. This is due to strong reflected light from the bumper. This is not a malfunction. ● The screen may flicker under fluorescent
light. This is not a malfunction.
● The colors of objects on the RearView Moni- tor may differ somewhat from those of the actual object.
● When the contrast of objects is low at night, pressing the SETTING button or MENU but- ton may not change the brightness.
● Objects on the monitor may not be clear in a
dark place or at night.
● If dirt, rain or snow attaches to the camera, the RearView Monitor may not display ob- jects. Clean the camera.
● Do not use body wax on the camera window. If body wax does get on the camera window, wipe off the wax with a clean cloth damp- ened with mild detergent diluted with water.
4-14 Monitor, climate, audio, phone and voice recognition systems
HEATER AND AIR CONDITIONER (manual) (if so equipped)
WARNING
● The air conditioner cooling function op- erates only when the engine is running. ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.
● Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.
Center vents
LHA2085
Adjust the air flow direction of the vents by mov- ing the slide as indicated 䊊1 .
Monitor, climate, audio, phone and voice recognition systems 4-15
Temperature control dial The temperature control dial allows you to adjust the temperature of the outlet air. To lower the temperature, turn the dial to the left. To increase the temperature, turn the dial to the right. Fresh air
Move the air intake lever to the The air flow is drawn from outside the vehicle. Air recirculation
position.
LHA2088
Move the air intake lever to the recirculate air inside the vehicle.
position to
1. 2. 3. 4. 5. 6.
Rear window defroster switch Fan control dial Air conditioner button (if so equipped) Air flow control dial Temperature control dial Air intake lever (Outside air circulation/ Air recirculation)
CONTROLS Fan control dial The fan control dial turns the fan on and off, and controls fan speed.
Air flow control dial The air flow control dial allows you to select the air flow outlets.
— Air flows from center and side
vents.
— Air flows from center and side vents
and foot outlets.
— Air flows mainly from foot outlets. — Air flows from defroster outlets and
foot outlets.
— Air flows mainly from defroster
outlets.
selection:
Use the ● when driving on a dusty road. ● to prevent traffic fumes from entering pas-
senger compartment.
● for maximum cooling when using the air con-
ditioner.
Air conditioner button (if so equipped)
Start the engine, turn the fan control dial to the button to desired position and press the turn on the air conditioner. The indicator light
4-16 Monitor, climate, audio, phone and voice recognition systems
comes on when the air conditioner is operating. To turn off the air conditioner, press the button again. The air conditioner cooling function oper- ates only when the engine is running. Rear window and outside mirror (if so equipped) defroster switch For more information about the rear window and outside mirror (if so equipped) defroster switch, see “Rear window and outside mirror defroster switch” in the “Instruments and controls” section of this manual. HEATER OPERATION Heating This mode is used to direct heated air to the foot outlets. Some air also flows from the defrost outlets.
1. Move the air intake lever to the
posi-
tion for normal heating.
2. Turn the air flow control dial to the
position.
3. Turn the fan control dial to the desired posi-
tion.
4. Turn the temperature control dial to the de- sired position between the middle and the hot position.
4. Turn the temperature control dial to the de- sired position between the middle and the hot position.
Ventilation This mode directs outside air to the side and center vents.
1. Move the air intake lever to the
posi-
tion.
2. Turn the air flow control dial to the
position.
3. Turn the fan control dial to the desired posi-
tion.
4. Turn the temperature control dial to the de-
sired position.
Defrosting or defogging This mode directs the air to the defrost outlets to defrost/defog the windows.
1. Move the air intake lever to the
posi-
tion.
2. Turn the air flow control dial to the
position.
3. Turn the fan control dial to the desired posi-
tion.
● To quickly remove ice or fog from the win- dows, turn the fan control dial to the maxi- mum position and the temperature control dial to the full hot position.
or position is selected, When the button to turn on the air condi- press the tioner for better performance. This will dehumidify the air and help defog the windows. Bi-level heating This mode directs cooler air from the side and center vents and warmer air from the floor outlets. When the temperature control dial is moved to the full hot or full cool position, the air between the vents and the floor outlets is the same tem- perature.
1. Move the air intake lever to
position.
2. Turn the air flow control dial to the
position.
3. Turn the fan control dial to the desired posi-
tion.
4. Turn the temperature control dial to the de-
sired position.
Monitor, climate, audio, phone and voice recognition systems 4-17
Heating and defogging This mode heats the interior and defogs the wind- shield.
1. Move the air intake lever to the
tion.
posi-
2. Turn the air flow control dial to the
position.
3. Turn the fan control dial to the desired posi-
tion.
4. Turn the temperature control dial to the de- sired position between the middle and the hot position.
or position is selected, When the press the button to turn on the air condi- tioner for better performance. This will dehumidify the air and help defog the windows. Operating tips Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater operation.
AIR CONDITIONER OPERATION (if so equipped) Start the engine, turn the fan control dial to the button to desired position, and press the activate the air conditioner. When the air condi- tioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function oper- ates only when the engine is running. Cooling This mode is used to cool and dehumidify the air.
● For quick cooling when the outside tem- perature is high, move the air intake lever to position. Be sure to return to the position for normal cooling. the
Dehumidified heating This mode is used to heat and dehumidify the air.
1. Move the air intake lever to the
posi-
tion.
2. Turn the air flow control dial to the
position.
3. Turn the fan control dial to the desired posi-
1. Move the air intake lever to the
posi-
tion.
tion.
2. Turn the air flow control dial to the
position.
4. Press the comes on.
button. The indicator light
5. Turn the temperature control dial to the de-
3. Turn the fan control dial to the desired posi-
sired position.
tion.
4. Press the comes on.
button. The indicator light
5. Turn the temperature control dial to the de-
sired position.
Dehumidified defogging This mode is used to defog the windows and dehumidify the air.
1. Move the air intake lever to the
posi-
tion.
2. Turn the air flow control dial to the
position.
4-18 Monitor, climate, audio, phone and voice recognition systems
3. Turn the fan control dial to the desired posi-
tion.
4. Turn the temperature control dial to the de-
sired position. Operating tips ● Keep the windows closed while the air con-
ditioner is in operation.
● After parking in the sun, drive for 2 or 3 min- utes with the windows open to vent hot air from the passenger compartment. Then, close the windows. This allows the air con- ditioner to cool the interior more quickly.
● The air conditioning system should be operated for approximately 10 minutes at least once a month. This helps pre- vent damage to the system due to lack of lubrication.
● A visible mist may be seen coming from the ventilators in hot, humid conditions as the air is cooled rapidly. This does not indicate a malfunction.
● If
the engine coolant
temperature gauge indicates engine coolant tem- perature over the normal range, turn the air conditioner off. See “If your vehicle overheats” in the “In case of emergency” section of this manual.
AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting. The air intake lever position for should always be in the heating and defrosting.
Monitor, climate, audio, phone and voice recognition systems 4-19
4-20 Monitor, climate, audio, phone and voice recognition systems
LHA2642
LHA2643
LHA2644
LHA2645
Monitor, climate, audio, phone and voice recognition systems 4-21
4-22 Monitor, climate, audio, phone and voice recognition systems
LHA2646
SERVICING AIR CONDITIONER (if so equipped)
AUDIO SYSTEM
The air conditioner system in your NISSAN ve- hicle is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is re- quired when servicing your NISSAN air condi- tioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system. See “Air conditioner system refrigerant and oil recommendations” in the “Technical and consumer information” section of this manual. A NISSAN dealer is able to service your “environ- mentally friendly” air conditioning system.
WARNING
The air conditioner system contains refrig- erant under high pressure. To avoid per- sonal injury, any air conditioner service should be done only by an experienced technician with proper equipment.
RADIO Place the ignition switch in the ACC or ON position and press the PWR button to turn the radio on. If you listen to the radio with the engine not running, the ignition switch should be placed in the ACC position.
Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external influ- ences. Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the vehicle may influence radio reception quality. Radio reception Your NISSAN radio system is equipped with state-of-the-art electronic circuits to enhance ra- dio reception. These circuits are designed to extend reception range, and to enhance the qual- ity of that reception.
However, there are some general characteristics of both FM and AM radio signals that can affect radio reception quality in a moving vehicle, even when the finest equipment is used. These char- acteristics are completely normal in a given re- ception area and do not indicate any malfunction in your NISSAN radio system.
Reception conditions will constantly change be- cause of vehicle movement. Buildings, terrain, signal distance and interference from other ve- hicles can work against ideal reception. De- scribed below are some of the factors that can affect your radio reception. Some cellular phones or other devices may cause interference or a buzzing noise to come from the audio system speakers. Storing the de- vice in a different location may reduce or elimi- nate the noise. FM RADIO RECEPTION Range: FM range is normally limited to 25 – 30 mi (40 – 48 km), with monaural (single channel) FM having slightly more range than stereo FM. Exter- nal influences may sometimes interfere with FM station reception even if the FM station is within 25 mi (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line- of-sight path, exhibiting many of the same char- acteristics as light. For example, they will reflect off objects. Fade and drift: As your vehicle moves away from a station transmitter, the signals will tend to fade and/or drift.
Monitor, climate, audio, phone and voice recognition systems 4-23
Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter), static or flutter can be heard. This can be reduced by adjusting the treble control to reduce treble response. Multipath reception: Because of the reflective characteristics of FM signals, direct and reflected signals reach the receiver at the same time. The signals may cancel each other, resulting in mo- mentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics, AM signals are also sub- ject to interference as they travel from transmitter to receiver. Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist. Static: Caused by thunderstorms, electrical power lines, electric signs and even traffic lights.
SATELLITE RADIO RECEPTION (if so equipped) When the satellite radio is used for the first time or the battery has been replaced, the satellite radio may not work properly. This is not a mal- function. Wait more than 10 minutes with satellite radio ON and the vehicle outside of any metal or large building for satellite radio to receive all of the necessary data. No satellite radio reception is available unless there is an active SiriusXM Satellite Radio service subscription. Satellite radio is not available in Alaska, Hawaii and Guam. If satellite radio is not operational then pressing the RADIO button will switch between FM and AM bands. Satellite radio performance may be affected if cargo carried on the roof blocks the satellite radio signal. If possible, do not put cargo over the satellite antenna. A build up of ice on the satellite radio antenna can affect satellite radio performance. Remove the ice to restore satellite radio reception.
4-24 Monitor, climate, audio, phone and voice recognition systems
LHA0099
AUDIO OPERATION PRECAUTIONSCompact disc (CD) player
CAUTION
● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player.
● Trying to load a CD with the CD door closed could damage the CD and/or CD changer.
● Only one CD can be loaded into the CD
player at a time.
● Only use high quality 4.7 in (12 cm) round discs that have the “COMPACT disc DIGITAL AUDIO” logo on the disc or packaging.
● During cold weather or rainy days, the player may malfunction due to the hu- midity. If this occurs, remove the CD and dehumidify or ventilate the player completely.
● The player may skip while driving on
rough roads.
● The CD player sometimes cannot func- tion when the compartment tempera- ture low. Decrease/increase the temperature before use.
extremely high or
is
● Do not expose the CD to direct sun-
light.
● CDs that are in poor condition or are dirty, scratched or covered with finger- prints may not work properly.
● The following CDs may not work prop-
erly: ● Copy control compact discs (CCCD) ● Recordable compact discs (CD-R) ● Rewritable compact discs (CD-RW) ● Do not use the following CDs as they may cause the CD player to malfunc- tion: ● 3.1 in (8 cm) discs with an adapter ● CDs that are not round ● CDs with a paper label ● CDs that are warped, scratched, or
have abnormal edges
CHECK DISC: ● Confirm that the CD is inserted cor- rectly (the label side is facing up, etc.).
● Confirm that the CD is not bent or
warped and it is free of scratches.
PRESS EJECT:
This is an error due to excessive tem- perature inside the player. Remove the CD by pressing the EJECT button. After a short time, reinsert the CD. The CD can be played when the temperature of the player returns to normal.
UNPLAYABLE:
The file is unplayable in this audio sys- tem (only MP3 or WMA (if so equipped) CD).
● This audio system can only play pre- recorded CDs. It has no capability to record or burn CDs.
● If the CD cannot be played, one of the following messages will be displayed.
Monitor, climate, audio, phone and voice recognition systems 4-25
● Sampling frequency — Sampling frequency is the rate at which the samples of a signal are converted from analog to digital (A/D conversion) per second.
● Multisession — Multisession is one of the methods for writing data to media. Writing data once to the media is called a single session, and writing more than once is called a multisession.
● ID3/WMA Tag — The ID3/WMA tag is the part of the encoded MP3 or WMA file that contains information about the digital music file such as song title, artist, encoding bit rate, track time duration, etc. ID3 tag infor- mation is displayed on the Artist/song title line on the display.
* Windows® and Windows Media® are regis- tered trademarks and trademarks in the United States of America and other countries of Micro- soft Corporation of the USA.
Compact disc with MP3 or WMA (if so equipped) Terms: ● MP3 — MP3 is short for Moving Pictures Experts Group Audio Layer 3. MP3 is the most well-known compressed digital audio file format. This format allows for near “CD quality” sound, but at a fraction of the size of normal audio files. MP3 conversion of an audio track from CD-ROM can reduce the file size by approximately a 10:1 ratio with virtually no perceptible loss in quality. MP3
compression removes the redundant and irrelevant parts of a sound signal that the human ear doesn’t hear.● WMA — Windows Media Audio (WMA)* is a compressed audio format created by Micro- soft as an alternative to MP3. The WMA codec offers greater file compression than the MP3 codec, enabling storage of more digital audio tracks in the same amount of space when compared to MP3s at the same level of quality.
● Bit rate — Bit rate denotes the number of bits per second used by a digital music file. The size and quality of a compressed digital audio file is determined by the bit rate used when encoding the file.
4-26 Monitor, climate, audio, phone and voice recognition systems
Playback order chart
WHA1078
Playback order: Music playback order of a CD with MP3 or WMA files is as illustrated. ● The names of folders not containing MP3 or
WMA files are not shown in the display.
● If there is a file in the top level of the disc,
“Root Folder” is displayed.
● The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.
Monitor, climate, audio, phone and voice recognition systems 4-27
Specification chart:
Supported media Supported file systems
Supported versions*1
MP3
WMA
Version Sampling frequency Bit rate Version Sampling frequency Bit rate
Tag information Folder levels Text character number limitation
Displayable character codes*2
CD, CD-R, CD-RW ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. MPEG1, MPEG2, MPEG2.5
8 kHz - 48 kHz 8 kbps - 320 kbps, VBR WMA7, WMA8, WMA9
32 kHz - 48 kHz 48 kbps - 192 kbps, VBR ID3 tag VER1.0, VER1.1, VER2.2, VER2.3 (MP3 only) Folder levels: 8, Max folders: 255 (including root folder), Files: 512 (Max. 255 files for one folder) 128 characters 01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE (UTF-16 Non-BOM Big Endian), 05: UNICODE (UTF-8), 06: UNICODE (Non-UTF-16 BOM Little Endian)*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.
*2 Available codes depend on what kind of media, versions and information are going to be displayed.
4-28 Monitor, climate, audio, phone and voice recognition systems
Troubleshooting guide:
Symptom
Cannot play
Poor sound quality
It takes a relatively long time before the music starts playing.
Music cuts off or skips
Skipping with high bit rate files Moves immediately to the next song when playing Songs do not play back in the desired order
Cause and Countermeasure
Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player. If there is a temperature increase error, the CD player will play correctly after it returns to the normal temperature. If there is a mixture of music CD files (CD-DA data) and MP3/WMA files on a CD, only the music CD files (CD-DA data) will be played. Files with extensions other than “.MP3”,“.WMA”, “.mp3” or “.wma” cannot be played. In addition, the character codes and number of characters for folder names and file names should be in compliance with the specifications. Check if the finalization process, such as session close and disc close, is done for the disc. Check if the disc is protected by copyright. Check if the disc is scratched or dirty. Bit rate may be too low. If there are many folders or file levels on the MP3/WMA disc, or if it is a multisession disc, some time may be required before the music starts playing.
The writing software and hardware combination might not match, or the writing speed, writing depth, writing width, etc., might not match the specifications. Try using the slowest writing speed. Skipping may occur with large quantities of data, such as for high bit rate data.
When a non-MP3/WMA file has been given an extension of “.MP3”, “.WMA”, .“mp3”or “.wma”, or when play is prohibited by copyright protection, there will be approximately 5 seconds of no sound and then the player will skip to the next song. The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.
Monitor, climate, audio, phone and voice recognition systems 4-29
USB (Universal Serial Bus) memory (if so equipped)
WARNING
Do not connect/disconnect or operate the USB device while driving. Doing so can be a distraction. If distracted you could lose control of your vehicle and cause an acci- dent or serious injury.
CAUTION
● Do not force the USB device into the USB port. Inserting the USB device tilted or up-side-down into the port may damage the port. Make sure that the USB device is connected correctly into the USB port.
● Do not grab the USB port cover (if so equipped) when pulling the USB device out of the port. This could damage the port and the cover.
● Do not leave the USB cable in a place where it can be pulled unintentionally. Pulling the cable may damage the port.
The vehicle is not equipped with a USB device. USB devices should be purchased separately as necessary.
This system cannot be used to format USB de- vices. To format a USB device, use a personal computer.
In some states/area, the USB device for the front seats plays only sound without images for regu- latory reasons, even when the vehicle is parked.
This system supports various USB memory de- vices, USB hard drives and iPod® players. Some USB devices may not be supported by this sys- tem. ● Partitioned USB devices may not play cor-
rectly.
● Some characters used in other languages (Chinese, Japanese, etc.) may not appear properly in the display. Using English lan- guage characters with a USB device is rec- ommended.
General notes for USB use: ● Refer to your device manufacturer’s owner information regarding the proper use and care of the device. Notes for iPod® use:
iPod® is a trademark of Apple Inc., registered in the U.S. and other countries.
4-30 Monitor, climate, audio, phone and voice recognition systems
● Improperly plugging in the iPod® may cause a checkmark to be displayed on and off (flickering). Always make sure that the iPod® is connected properly.
● An iPod® nano (1st Generation) may remain in fast forward or rewind mode if it is con- nected during a seek operation. In this case, please manually reset the iPod®.
● An iPod® nano (2nd Generation) will con- tinue to fast-forward or rewind if it is discon- nected during a seek operation.
● An incorrect song title may appear when the Play Mode is changed while using an iPod® nano (2nd Generation).
● Audiobooks may not play in the same order
as they appear on an iPod®.
● Large video files cause slow responses in an iPod®. The vehicle center display may mo- mentarily black out, but will soon recover.
● If an iPod® automatically selects large video files while in the shuffle mode, the vehicle center display may momentarily black out, but will soon recover.
11. VOLUME control knob 12. PWR button 13. SCAN button 14. RDM button 15. Station select (1 - 6) buttons FM/AM RADIO WITH COMPACT DISC (CD) PLAYER (Type A) (if so equipped) For all operation precautions, see “Audio opera- tion precautions” in this section. Audio main operation POWER/VOLUME control:
Place the ignition switch in the ACC or ON position. Press the PWR button while the system is off to call up the mode (radio, CD or AUX) that was playing immediately before the system was turned off. While the system is on, pressing the PWR button turns the system off. Turn the VOL control knob to adjust the volume. MENU button (Bass, Treble, Fade, Balance and Clock): Press the MENU button to change the mode as follows: BAS (Bass) → TRE (Treble) → FAD (Fade) → BAL (Balance) → Clock → Normal mode
LHA1224
Type A AUX button 6. 7. TUNE button 8. MENU button 9. RPT button 10. AUX IN jack
Monitor, climate, audio, phone and voice recognition systems 4-31
CD eject button
FM-AM button
1. 2. 3. 4. CD button 5. CD insert slot
SEEK button
or
or TUNE
Press the SEEK button to adjust the Bass, Treble, Fade or and Balance to the desired level. Fade adjusts the sound level between the front and rear speak- ers and Balance adjusts the sound between the right and left speakers. Once you have adjusted the sound quality to the desired level, press the MENU button repeatedly until the radio or CD display reappears. If no action is taken, the radio or CD display will auto- matically reappear after approximately 10 sec- onds. Clock set If the clock is not displayed with the ignition switch in the ACC or ON position, you need to select the CLK-ON mode. Press the MENU but- ton repeatedly until CLK-OFF mode is displayed. Use the TUNE/FF-REW/FOLDER button to en- able CLK-ON mode. 1. Press the MENU button repeatedly until “Clock:” appears. The hours will begin flash- ing.
2. Press the SEEK button
the TUNE button the hours.
or
or to adjust
or
3. Press the MENU button again. The minutes
will begin flashing.
4. Press the SEEK button
the TUNE button the minutes.
or
or to adjust
or
5. Press the MENU button again to exit the
clock set mode.
If no action is taken, the display will return to the regular clock display after 10 seconds. FM/AM radio operation FM·AM button:
Press the FM·AM button to change the band as follows: AM → FM1 → FM2 → AM If another audio source is playing when the FM·AM button is pressed, the audio source play- ing will automatically be turned off and the last radio station played will begin playing.
The FM stereo indicator (ST) illuminates during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception.
TUNE button (Tuning):
Press the TUNE button manual tuning.
or
for
SEEK tuning:
to tune Press the SEEK button from low to high or high to low frequencies and to stop at the next broadcasting station. SCAN tuning:
or
Press the SCAN button to stop at each broad- casting station for 5 seconds. Pressing the but- ton again during this 5 second period will stop SCAN tuning and the radio will remain tuned to that station. If the SCAN button is not pressed within 5 seconds, SCAN tuning moves to the next station. 1 to 6 Station memory operations:
Twelve stations can be set for the FM band (6 for FM1, 6 for FM2) and six stations can be set for the AM band.
1. Choose the radio band AM, FM1 or FM2
using the AM·FM select button.
2. Tune to the desired station using manual, SEEK or SCAN tuning. Press and hold any of the desired station memory buttons (1 – 6) until a beep sound is heard.
3. The channel indicator will then come on and the sound will resume. Programming is now complete.
4-32 Monitor, climate, audio, phone and voice recognition systems
4. Other buttons can be set in the same man-
SEEK button:
ner.
If the battery cable is disconnected or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Compact disc (CD) player operation If the radio is already operating, it automatically turns off and the compact disc begins to play. CD button:
When the CD button is pressed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play.
When the CD button is pressed with a compact disc loaded and the radio playing, the radio will automatically be turned off and the compact disc will start to play.
TUNE (Rewind or Fast Forward) button:
or
is When the TUNE button pressed while the compact disc is playing, the compact disc plays at an increased speed while reversing or fast forwarding. When the button is released, the compact disc returns to normal play speed.
When the SEEK button is pressed while the compact disc is playing, the next track follow- ing the present one starts to play from the begin- several times ning. Press the SEEK button to skip several tracks. Each time the button is pressed, the CD advances one additional track. The track number appears in the display window. (When the last track on the compact disc is skipped, the first track is played.)
is pressed, the When the SEEK button track being played returns to the beginning. several times to Press the SEEK button skip back several tracks. Each time the button is pressed the CD moves back one track. RDM button:
When the RDM button is pressed while a com- pact disc is playing, the play pattern can be changed as follows: 1 CD RDM←→ 1 CD RPT 1 CD RDM: all tracks on the disc will be played randomly.
1 CD RPT: play pattern returns to normal.
RPT button: When the RPT button is pressed while a com- pact disc is playing, the play pattern can be changed as follows: 1 TR RPT←→ 1 CD RPT 1 TR RPT: the current track will be repeated. 1 CD RPT: play pattern returns to normal. AUX (Auxiliary) button: The AUX IN jack is located on the front of the radio. The AUX IN audio input jack accepts any standard analog audio input such as from a por- table cassette tape/CD player, MP3 player or a laptop computer. Press the AUX button to play a compatible device when it is plugged into the AUX IN jack.
EJECT button:
button is pressed with a com- When the pact disc loaded, the compact disc will eject and the last source will be played.
button is pressed twice with a When the compact disc loaded, the compact disc will be ejected further for easier CD removal. If the disc is not removed within 15 seconds, the disc will reload.
Monitor, climate, audio, phone and voice recognition systems 4-33
11. FM button 12. VOL (volume) control knob / power
button
button
SEEK button
13. Station select (1 - 6) buttons 14. TRACK 15. FM/AM RADIO WITH COMPACT DISC (CD) PLAYER (Type B) (if so equipped) For all operation precautions, see “Audio opera- tion precautions” in this section. Audio main operation VOL (volume) control knob / power button Place the ignition switch in the ACC or ON position, then press the VOL (volume) control knob / power button. If you listen to the radio with the engine not running, place the ignition in the ACC position. The mode (radio or CD) that was playing immediately before the system was turned off resumes playing. When no CD is loaded, the radio comes on. Pressing the VOL (volume) control knob / power button again turns the system off. Turn the VOL (volume) control knob / power button to the right to increase volume or to the left to decrease volume.
CD eject button
1. 2. CD insert slot 3. SCAN button DISP button 4. 5. RPT/RDM button 4-34 Monitor, climate, audio, phone and voice recognition systems
Type B TUNE/FOLDER knob / MENU button 6. AUX IN jack 7. 8. AUX button 9. CD button 10. AM button
LHA8804
MENU button (Bass, Treble, Balance, Fade, Speed Sensitive Volume and Clock):
Press the MENU button to change the mode as follows: Bass → Treble → Balance → Fade → Spd. Sen. Vol. (Speed Sensitive Volume) → AUX IN Volume → Clock → Clock Adjust To adjust the Bass, Treble, Fade and Balance, press the MENU button until the desired mode SEEK or appears in the display. Press the button to adjust the setting to the TRACK desired level (-5 to +5). Balance adjusts the sound between the right and left speakers. Fade adjusts the sound between the front and rear speakers.
Once you have adjusted the sound quality to the desired level, press the MENU button repeatedly until the radio or CD display reappears. Other- wise, the radio or CD display will automatically reappear after about 10 seconds.
Speed Sensitive Volume (SSV) adjusts the vol- ume of the audio system as the vehicle’s driving speed changes. It can be set as follows: OFF → LOW → MID → HIGH
DISP (display) button:
2. Press the ENTER button.
Press the DISP (display) button while a CD is playing to change the text shown in the audio display as follows:
3. “Change Hour” will appear on the screen. Turn the TUNE/FOLDER knob to adjust the hours and then press ENTER.
For CDs: Running Time → Album Title: → Artist Name: → Song Title
For MP3 CDs: Running Time → Folder Title: → Album Title: → Artist Name: → Song Title: If the text information is too long to fully be dis- played on the screen; press and hold the DISP button for longer than 1.5 seconds to scroll through the rest of the text. Press the DISP (display) button while the radio is playing to toggle the audio display between sta- tion number and RDS. Clock operation To turn the clock display on or off, press the MENU button repeatedly until “Clock” appears on the display. Turn the TUNE/FOLDER knob to toggle the setting (ON or OFF). Clock set 1. Press the MENU button repeatedly until
“Adjust Clock” appears on the display.
4. “Change Minute” will appear on the screen. Turn the TUNE/FOLDER knob to adjust the minutes and then press ENTER.
The display will return to the regular clock display after 10 seconds if no further adjustment is per- formed. FM/AM radio operation AM and FM buttons:
Press the AM button to change the band to AM.
If another audio source is playing when the AM button is pressed, the audio source playing will automatically be turned off and the last radio station played will begin playing.
Press the FM button to change the band as follows: FM1 → FM2 → FM1
If another audio source is playing when the FM button is pressed, the audio source playing will automatically be turned off and the last radio station played will begin playing.Monitor, climate, audio, phone and voice recognition systems 4-35
The FM stereo indicator (ST) illuminates during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception.
SEEK and TRACK (tuning) buttons:
Press the SEEK button to tune from low to high frequencies and stop at the next broadcast- ing station.
to tune from high Press the TRACK button to low frequencies and stop at the next broad- casting station.
Press and hold either button to seek at a faster speed. SCAN (tuning) button:
Press the SCAN button. SCAN illuminates in the display window. Scan tuning begins from low to high frequencies. Scan tuning stops for 5 sec- onds at each broadcasting station that has suffi- cient signal strength. When scanning, SCAN blinks in the display. Pressing the SCAN button again during this 5 second period stops scan tuning and the radio remains tuned to that station.
1 to 6 Station memory operations:
CD button:
Twelve stations can be set for the FM band (6 for FM1, 6 for FM2) and six stations can be set for the AM band.
When the CD button is pressed with a compact disc loaded and the radio playing, the radio turns off and the last used compact disc starts to play.
1. Choose the radio band AM, FM1 or FM2
using the AM or FM button.
2. Tune to the desired station using manual, SEEK or SCAN tuning. Press and hold any of the desired station memory buttons (1 – 6) until a beep sound is heard.
3. The channel indicator will then come on and the sound will resume. Programming is now complete.
4. Other buttons can be set in the same man-
ner.
If the battery cable is disconnected or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Compact disc (CD) player operation Place the ignition switch in the ACC or ON position, and carefully insert the compact disc into the slot with the label side up. The compact disc is automatically pulled into the slot and starts to play. If the radio is already operating, it automatically turns off and the compact disc begins to play.
SEEK and TRACK (Fast Forward, Rewind) but- tons:
or TRACK
When the SEEK button button is pressed while the compact disc is play- ing, the compact disc plays at an increased speed while fast forwarding or rewinding. When the button is released, the compact disc returns to normal play speed.
SEEK and TRACK buttons:
When the SEEK button is pressed while the compact disc is playing, the next track follow- ing the present one starts to play from the begin- button several times ning. Press the SEEK to skip several tracks. Each time the button is pressed, the CD advances one additional track. The track number appears in the display window. (When the last track on the compact disc is skipped, the first track is played.)
4-36 Monitor, climate, audio, phone and voice recognition systems
Press the MENU button repeatedly until “AUX IN Volume” appears on the screen to control the incoming volume level of the auxiliary input de- vice. Turn the TUNE/FOLDER knob to adjust the level between 0 and +3.
When the TRACK button is pressed, the track being played returns to the beginning. button several times to Press the TRACK skip back several tracks. Each time the button is pressed the CD moves back one track. RPT/RDM button:
Press the RPT/RDM button while a compact disc is playing to change the play pattern as follows: CD: TRACK REPEAT → DISC RANDOM → DISC REPEAT MP3/WMA CD: FOLDER REPEAT → TRACK REPEAT → DISC RANDOM → FOLDER RANDOM → DISC RE- PEAT TRACK REPEAT: The track that is currently play- ing will be repeated. DISC RANDOM: The order of the tracks on the disc will be mixed during play. DISC REPEAT: The disc currently playing will be repeated. FOLDER REPEAT: The tracks in the current folder will be repeated. FOLDER RANDOM: The order of the tracks in the folder will be mixed during play.
SCAN (CDs) button: Press the SCAN button for less than 1.5 seconds to scan all tracks of the current disc for 10 sec- onds per track. The SCAN icon is flashed during scan mode. The scan mode is canceled once it scans through all tracks on the disc, or if the SCAN button is pressed during scan mode.
CD EJECT:
When the pact disc loaded, ejected.
button is pressed with a com- the compact disc will be
button is pressed while the When the compact disc is playing, the compact disc will eject and the system will turn off. AUX (Auxiliary) button: The AUX IN jack is located on the CD player. The AUX IN audio input jack accepts any standard analog audio input such as from a portable cas- sette tape/CD player, MP3 player or laptop com- puters. Press the AUX button to play a compatible device when it is plugged into the AUX IN jack.
Monitor, climate, audio, phone and voice recognition systems 4-37
12.Station select (1 - 6) buttons 13.RDM button 14.RPT button 15.DISP button
