2010 Nissan Sentra Owners Manual

serted into the ignition switch. The shift selector is not in the P (Park) position. The battery charge is low.

The ignition switch is not placed in the LOCK position. The Intelligent Key is not in the vehicle.

Place the ignition switch in the LOCK position.

Remove the mechanical key from the ignition switch.

Make sure that the shift selector is in the P (Park) posi- tion and place the ignition switch in the LOCK position. Replace the battery with a new one. See (cid:147)Battery re- placement(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section. Place the ignition switch in the LOCK position.

If the Intelligent Key warning light illuminates red even while you are carrying the Intelligent Key, the battery is completely discharged. Replace the battery with a new one. See (cid:147)Battery replacement(cid:148) in the (cid:147)Maintenance and do-it-yourself(cid:148) section.

3-22 Pre-driving checks and adjustments

HOOD

TRUNK LID

1. Pull the hood lock release handle s1 located below the instrument panel until the hood springs up slightly.

2. Locate the lever s2 in between the hood and grille and push the lever sideways with your fingertips.

3. Raise the hood s3 . 4. Remove the support rod s4 and insert it into

the slot on the underside of the hood s5 .

WPD0383
When closing the hood, return the support rod to it(cid:146)s original position, lower the hood to approxi- mately 30 cm (12 inches) above the latch and release it. This allows proper engagement of the hood latch.

WARNING

c Make sure the hood is completely closed and latched before driving. Fail- ure to do so could cause the hood to fly open and result in an accident.

c If you see steam or smoke coming from the engine compartment, to avoid injury do not open the hood.

WARNING

c Do not drive with the trunk lid open. This could allow dangerous exhaust gases to be drawn into the vehicle. See (cid:147)Ex- haust gas(cid:148) in the (cid:147)Starting and driving(cid:148) section of this manual.

c Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously in- jured. Keep the car locked, with the rear seatback and trunk lid securely latched when not in use, and prevent children(cid:146)s access to car keys.

Pre-driving checks and adjustments 3-23

Driver(cid:146)s side

WPD0390

TRUNK LID RELEASE The trunk lid release is located on the floor to the left of the driver(cid:146)s seat. To open the trunk lid, pull the trunk lid release. To close the trunk lid, lower and push the trunk lid down securely. You can also open the trunk lid with the keyfob (if so equipped) or Intelligent Key (if so equipped). Refer to (cid:147)Remote keyless entry system(cid:148) or (cid:147)NISSAN Intelligent Key(cid:153)(cid:148) in this section.

3-24 Pre-driving checks and adjustments

WPD0384

WPD0385

KEY OPERATION (if so equipped) To open the trunk lid, turn the key clockwise. To close the trunk lid, lower and push the trunk lid down securely.

INTERIOR TRUNK LID RELEASE

WARNING

Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured. Keep the car locked, with the rear seatback and trunk lid securely latched when not in use, and prevent children(cid:146)s access to car keys.

The interior trunk lid release mechanism provides a means of escape for children and adults in the event they become locked inside the trunk.

FUEL-FILLER DOOR

To open the trunk from the inside, pull the illumi- nated release handle until the lock releases and push up on the trunk lid. The release handle is made of a material that glows in the dark after a brief exposure to ambient light. The handle is located inside the trunk compart- ment on the interior of the trunk lid.

LPD0386

LPD0387

OPENER OPERATION The fuel-filler door release is located on the floor to the left of the driver(cid:146)s seat. To open the fuel- filler door, push the release. To lock, close the fuel-filler door securely.

FUEL-FILLER CAP The fuel-filler cap is a ratcheting type. Turn the cap counterclockwise to remove. To tighten, turn the cap clockwise until ratcheting clicks are heard. Put the fuel-filler cap on the cap holder s1 while refueling.

Pre-driving checks and adjustments 3-25

c Do not fill a portable fuel container in the vehicle or trailer. Static electricity can cause an explosion of flammable liquid, vapor or gas in any vehicle or trailer. To reduce the risk of serious injury or death when filling portable fuel containers: (cid:150) Always place the container on the

ground when filling.

(cid:150) Do not use electronic devices when

filling.

(cid:150) Keep the pump nozzle in contact with the container while you are fill- ing it.

(cid:150) Use only approved portable fuel con-

tainers for flammable liquid.

WARNING

c Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.

c Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.

c Use only an original equipment type fuel-filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emis- sion control system. An incorrect cap can result in a serious malfunction and possible injury. It could also cause the malfunction indicator light to come on. c Never pour fuel into the throttle body to

attempt to start your vehicle.

3-26 Pre-driving checks and adjustments

CAUTION

c If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.

c Insert the fuel-filler cap straight into the fuel-filler tube, then tighten until the fuel-filler cap clicks. Failure to tighten the fuel-filler cap properly may cause the Malfunction Indicator Light

light (MIL) to illuminate. If the illuminates because the fuel-filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The light should turn off after a

If the

few driving trips. light does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer c For additional

information, see the (cid:147)Malfunction Indicator Light (MIL)(cid:148) in the (cid:147)Instruments and Controls(cid:148) section in this manual.

STEERING WHEEL

SUN VISORS

LPD0388

TILT OPERATION Push the lock lever s1 down and adjust the steering wheel up or down s2 to the desired position. Pull the lock lever up to lock the steering wheel in place.

WARNING

Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.

SIC2872
To block out glare from the front, swing down the sun visor s1 . To block glare from the side, disconnect the sun visor from the center mount and swing it to the side s2 .

LPD0389

VANITY MIRRORS (if so equipped) To access the vanity mirror, pull the sun visor down and flip open the mirror cover. Some vanity mirrors are illuminated and turn on when the mirror cover is open.

Pre-driving checks and adjustments 3-27

OUTSIDE MIRRORS

WARNING

Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.

LPD0029

Manual control type (if so equipped) The outside mirror can be moved in any direction for a better rear view.

MIRRORS

WPD0126

REARVIEW MIRROR The night position s1 reduces glare from the headlights of vehicles behind you at night. Use the day position s2 when driving in daylight hours.

WARNING

Use the night position only when neces- sary, because it reduces rear view clarity.

3-28 Pre-driving checks and adjustments

Heated mirrors (Canada only) (if so equipped) Some outside mirrors can be heated to defrost, defog, or de-ice for improved visibility. Push the rear window defroster switch to activate the heat- ing function. Push the switch again to deactivate, or the heating function will automatically turn off after approximately 15 minutes.

WPD0274

Electric control type (if so equipped) The outside mirror remote control only operates when the ignition switch is in the ACC or ON position. Rotate the control lever to select the right or left mirror. Adjust the mirror to the desired position by moving the control lever.

Pre-driving checks and adjustments 3-29

MEMO

3-30 Pre-driving checks and adjustments

4 Display screen, heater, air conditioner, audio and phone systems

RearView Monitor (if so equipped). . . . . . . . . . . . . . . . . . . 4-2
How to read the displayed lines . . . . . . . . . . . . . . . . . . 4-2
Adjusting the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Operating tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Heater and air conditioner (manual). . . . . . . . . . . . . . . . . . 4-4
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Heater operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
Air conditioner operation (if so equipped) . . . . . . . . . 4-8
Air flow charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
Servicing air conditioner (if so equipped) . . . . . . . . . . . . 4-12
Audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-13
FM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
AM radio reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Satellite radio reception (if so equipped) . . . . . . . . . 4-14
Audio operation precautions . . . . . . . . . . . . . . . . . . . . 4-14
FM/AM radio with compact disc (CD) player (Type A) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . 4-21
FM/AM radio with compact disc (CD) player (Type B) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . 4-24

FM/AM/SAT radio with compact disc (CD) player (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . 4-28
iPodT* Player Operation (Type A) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34
iPodT* Player Operation (Type B) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35
USB interface (if so equipped) . . . . . . . . . . . . . . . . . . 4-37
CD care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39
Steering wheel switch for audio control (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-40
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41
Car phone or CB radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41
BluetoothT Hands-Free Phone System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . 4-44
Using the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-44
Control buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-46
Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-47
List of voice commands . . . . . . . . . . . . . . . . . . . . . . . . 4-49
Speaker adaptation (SA) mode. . . . . . . . . . . . . . . . . . 4-53
Manual Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-55
Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . 4-56

REARVIEW MONITOR (if so equipped)

When the shift selector is shifted into the R (Reverse) position, the monitor display shows the view directly to the rear of the vehicle.

WARNING

c The system is designed as an aid to the driver in detecting large stationary ob- jects to help avoid damaging the ve- hicle. The system will not detect small objects below the bumper, and may not detect objects close to the bumper or on the ground.

c The RearView Monitor is a convenience but it is not a substitute for proper back- ing. Always turn and check that it is safe to do so before backing up. Always back up slowly.

c Objects viewed in the RearView Moni- tor differ from actual distance because a wide-angle lens is used.

c Make sure that the trunk is securely

closed when backing up.

c Do not put anything on the rearview camera. The rearview camera is in- stalled beside the license plate light.

c When washing the vehicle with high- pressure water, be sure not to spray it around the camera. Otherwise, water may enter the camera unit causing wa- ter condensation on the lens, a mal- function, fire or an electric shock.

c Do not strike the camera. It is a preci- sion instrument. Otherwise, it may mal- function or cause damage resulting in a fire or an electric shock.

CAUTION

There is a plastic cover over the camera. Do not scratch the cover when cleaning dirt or snow from the cover. HOW TO READ THE DISPLAYED LINES Lines which indicate the vehicle clearance and distances to objects with reference to the bumper line sA are displayed on the monitor.

4-2 Display screen, heater, air conditioner, audio and phone systems

LHA0437
They are indicated as reference distances to objects. The lines and colors in the display indi- cate distances from the back bumper line sA in the illustration. s1 1.5 ft (0.5 m) red s2 3 ft (1 m) yellow s3 7 ft (2 m) green s4 10 ft (3 m) green The vehicle clearance lines are wider than the actual clearance.

OPERATING TIPS c When the shift selector is shifted to R (Re- verse), the monitor screen automatically changes to the RearView Monitor mode. However, the radio can be heard.

c It may take some time until the RearView Monitor is displayed after the shift selector has been shifted to R (Reverse). Objects may be distorted momentarily until the Rear- View Monitor screen is displayed com- pletely. When the shift selector is returned to a position other than R (Reverse), it may take some time until the screen changes. Objects on the screen may be distorted until they are completely displayed.

c When the temperature is extremely high or low, the screen may not clearly display ob- jects. This is not a malfunction.

c When strong light directly enters the cam-

era, objects may not be displayed clearly.

c Vertical lines may be seen in objects on the screen. This is due to strong reflected light from the bumper. This is not a malfunction. c The screen may flicker under fluorescent

light. This is not a malfunction.

c The colors of objects on the RearView Moni- tor may differ somewhat from those of the actual object.

c When the contrast of objects is low at night, pressing the SETTING button may not change the brightness.

c Objects on the monitor may not be clear in a

dark place or at night.

c If dirt, rain or snow attaches to the camera, the RearView Monitor may not display ob- jects. Clean the camera.

c Do not use alcohol, benzine or thinner to clean the camera. This will cause discolora- tion. To clean the camera, wipe with a cloth dampened with a diluted mild cleaning agent and then wipe with a dry cloth.

c Do not damage the camera as the monitor

screen may be adversely affected.

c Do not use body wax on the camera window. If body wax does get on the camera window, wipe off the wax with a clean cloth damp- ened with mild detergent diluted with water.

Display screen, heater, air conditioner, audio and phone systems 4-3

LHA1272

ADJUSTING THE SCREEN To adjust the quality of the screen, press the setting control knob on the audio system. c To adjust the Brightness or Contrast, press the setting control knob repeatedly until the setting you wish to adjust is displayed. Use the TUNE/SCROLL knob to adjust the dis- play to the desired level.

c Do not adjust the Brightness or Contrast of the RearView Monitor while the vehicle is moving.

VENTS

WHA0772

Adjust air flow direction for the driver(cid:146)s and pas- senger(cid:146)s side s1 , and center s2 ventilators by moving the ventilator slide and/or ventilator as- semblies. Open or close the ventilators s1 by using the dial. to open the ven- Move the dial toward the tilators or toward the

to close them.

4-4 Display screen, heater, air conditioner, audio and phone systems

HEATER AND AIR CONDITIONER (manual)

WARNING

c The air conditioner cooling function op- erates only when the engine is running. c Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.

c Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

Type A

WHA0470

1. 2. 3. 4. 5.

Fan control dial Air recirculation button Temperature control dial Air flow control dial Rear window defroster

Display screen, heater, air conditioner, audio and phone systems 4-5

(cid:151) Air flows mainly from foot

outlets.

(cid:151) Air flows from defroster out-

lets and foot outlets.

(cid:151) Air flows mainly from de-

froster outlets.

c You can also select

the middle position

between and

and

or between

c When the

or

position is mode selected, the air recirculation cannot be turned on. This prevents the win- dows from fogging.

Temperature control dial The temperature control dial allows you to adjust the temperature of the outlet air. To lower the temperature, turn the dial to the left. To increase the temperature, turn the dial to the right.

Air recirculation button

NOTE: The air recirculation feature is available only on those vehicles equipped with air conditioning.

Type B

LHA0440

Fan control dial Air recirculation button Temperature control dial Air conditioner button Air flow control dial Rear window defroster

1. 2. 3. 4. 5. 6. CONTROLS Fan control dial The fan control dial turns the fan on and off, and controls fan speed.

Air flow control dial The air flow control dial allows you to select the air flow outlets. MAX A/C (cid:151) Air flows from center and side vents with maximum cooling (air conditioning if so equipped).

(cid:151) Air flows from center and

side vents.

(cid:151) Air flows from center and

side vents and foot outlets.

4-6 Display screen, heater, air conditioner, audio and phone systems

On position (Indicator light on): Interior air is recirculated inside the vehicle.

button to the on position when:

Press the c driving on a dusty road. c to prevent traffic fumes from entering pas-

senger compartment.

c for maximum cooling when using the air con-

ditioner.

When the button is pressed, the air con- ditioner automatically turns on and the indicator illuminates. When the button is pressed again, the air recirculation mode turns off, but the air conditioner remains on. Off position (Indicator light off): Outside air is drawn into the passenger compart- ment and distributed through the selected outlet. Use the off position for normal heater or air con- ditioner operation.

Air conditioner button (if so equipped)

The button is provided only on vehicles equipped with an air conditioner. Start the engine, turn the fan control dial to the desired position and push the button to

turn on the air conditioner. The indicator light comes on when the air conditioner is operating. To turn off the air conditioner, push the button again. The air conditioner cooling function oper- ates only when the engine is running. Rear window defroster switch For more information about the rear window de- froster switch, see (cid:147)Rear window and outside mirror defroster switch(cid:148) in the (cid:147)Instruments and controls(cid:148) section of this manual. HEATER OPERATION Heating This mode is used to direct heated air to the foot outlets. Some air also flows from the defrost outlets and outboard vents.

1. Push the

normal heating.

button to the off position for

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de- sired position between the middle and the hot position.

Ventilation This mode directs outside air to the side and center vents.

1. Push the

button to the off position.

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de-

sired position.

Defrosting or defogging This mode directs the air to the defrost outlets and outboard vents to defrost/defog the win- dows.

1. Turn the air flow control dial to the

position.

2. Turn the fan control dial to the desired posi-

tion.

3. Turn the temperature control dial to the de- sired position between the middle and the hot position.

Display screen, heater, air conditioner, audio and phone systems 4-7

c To quickly remove ice or fog from the win- dows, turn the fan control dial to HI and the temperature control lever to the full HOT position.

c When the

or

position is se- lected, the air conditioner automatically turns on (however, the indicator light will not illuminate). In this position, the A/C cannot be turned off. When the air flow control dial is turned to any position other than or illuminate (the A/C will continue operating) and can be turned off using the A/C button. This dehu- midifies the air which helps defog the wind- shield. The mode automatically turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance.

, the A/C light will

Bi-level heating This mode directs air from the side, center and the foot outlets.

1. Push the

button to the off position.

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Turn the temperature control dial to the de-

sired position.

Heating and defogging This mode heats the interior and defogs the wind- shield.

1. Turn the air flow control dial to the

position.

2. Turn the fan control dial to the desired posi-

tion.

3. Turn the temperature control dial to the de- sired position between the middle and the hot position.

c When the

or

position is se- lected, the air conditioner automatically turns on (however, the indicator light will not illuminate). In this position, the A/C cannot be turned off. When the air flow control dial is turned to any position other than or illuminate (the A/C will continue operating) and can be turned off using the A/C button. This dehu- midifies the air which helps defog the wind- shield. The mode automatically turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance.

the A/C light will

Operating tips Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater operation. AIR CONDITIONER OPERATION (if so equipped) Start the engine, turn the fan control dial to the desired position, and push in the button to activate the air conditioner. When the air condi- tioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function oper- ates only when the engine is running. Cooling This mode is used to cool and dehumidify the air.

1. Push the 2. Turn the air flow control dial to the MAX A/C

button to the off position.

or

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Push the comes on.

button. The indicator light

5. Turn the temperature control dial to the de-

sired position.

4-8 Display screen, heater, air conditioner, audio and phone systems

c For quick cooling when the outside tem- perature is high, push the button to the on position (indicator light on). Be sure to return the button to the off position for normal cooling. MAX A/C may be used for quick cooling.

Dehumidified heating This mode is used to heat and dehumidify the air.

1. Push the

button to the off position.

2. Turn the air flow control dial to the

position.

3. Turn the fan control dial to the desired posi-

tion.

4. Push the comes on.

button. The indicator light

5. Turn the temperature control dial to the de-

sired position.

Dehumidified defogging This mode is used to defog the windows and dehumidify the air.

1. Turn the air flow control dial to the

position.

2. Turn the fan control dial to the desired posi-

tion.

3. Push the comes on.

button. The indicator light

or

or

When the position is selected, the air conditioner automatically turns on (how- ever, the indicator light will not illuminate). In this position, the A/C cannot be turned off. When the air flow control is turned to any position other than the A/C light will illuminate (the A/C will continue operating) and can be turned off using the A/C button. This dehumidi- fies the air which helps defog the windshield. The mode automatically turns off, allowing outside air to be drawn into the passenger com- partment to further improve the defogging perfor- mance.

4. Turn the temperature control dial to the de-

sired position. Operating tips c Keep the windows and moonroof closed

while the air conditioner is in operation.

c After parking in the sun, drive for 2 or 3
minutes with the windows open to vent hot air from the passenger compartment. Then, close the windows. This allows the air con- ditioner to cool the interior more quickly.

c The air conditioning system should be operated for approximately 10 minutes at least once a month. This helps pre- vent damage to the system due to lack of lubrication.

c A visible mist may be seen coming from the vents in hot, humid conditions as the air is cooled rapidly. This does not indicate a mal- function.

c If

the engine coolant

temperature gauge indicates engine coolant tem- perature over the normal range, turn the air conditioner off. See (cid:147)If your vehicle overheats(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual.

AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting. The air recirculation button should always be in the OFF posi- tion for heating and defrosting.

Display screen, heater, air conditioner, audio and phone systems 4-9

4-10 Display screen, heater, air conditioner, audio and phone systems

WHA1116

WHA1117

WHA1118

WHA1119

Display screen, heater, air conditioner, audio and phone systems 4-11

SERVICING AIR CONDITIONER (if so equipped)

The air conditioner system in your NISSAN ve- hicle is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth(cid:146)s ozone layer. Special charging equipment and lubricant is re- quired when servicing your NISSAN air condi- tioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system. See (cid:147)Air conditioner system refrigerant and oil recommendations(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual. A NISSAN dealer is able to service your (cid:147)environ- mentally friendly(cid:148) air conditioning system.

WARNING

The air conditioner system contains re- frigerant under high pressure. To avoid personal injury, any air conditioner ser- vice should be done only by an experi- enced technician with proper equipment.

4-12 Display screen, heater, air conditioner, audio and phone systems

WHA1121

AUDIO SYSTEM

RADIO Place the ignition switch in the ACC or ON position and press the POWER/VOLUME con- trol knob to turn the radio on. If you listen to the radio with the engine not running, the ignition switch should be placed in the ACC position.

Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external influ- ences. Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the ve- hicle may influence radio reception quality. Radio reception Your NISSAN radio system is equipped with state-of-the-art electronic circuits to enhance ra- dio reception. These circuits are designed to extend reception range, and to enhance the qual- ity of that reception.

However, there are some general characteristics of both FM and AM radio signals that can affect radio reception quality in a moving vehicle, even when the finest equipment is used. These char- acteristics are completely normal in a given re- ception area and do not indicate any malfunction in your NISSAN radio system.

Reception conditions will constantly change be- cause of vehicle movement. Buildings, terrain, signal distance and interference from other ve- hicles can work against ideal reception. De- scribed below are some of the factors that can affect your radio reception. Some cellular phones or other devices may cause interference or a buzzing noise to come from the audio system speakers. Storing the de- vice in a different location may reduce or elimi- nate the noise. FM RADIO RECEPTION Range: FM range is normally limited to 25 (cid:150) 30 mi (40 (cid:150) 48 km), with monaural (single channel) FM having slightly more range than stereo FM. Exter- nal influences may sometimes interfere with FM station reception even if the FM station is within 25 mi (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line- of-sight path, exhibiting many of the same char- acteristics as light. For example, they will reflect off objects. Fade and drift: As your vehicle moves away from a station transmitter, the signals will tend to fade and/or drift.

Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter), static or flutter can be heard. This can be reduced by adjusting the treble control to reduce treble response. Multipath reception: Because of the reflective characteristics of FM signals, direct and reflected signals reach the receiver at the same time. The signals may cancel each other, resulting in mo- mentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics, AM signals are also sub- ject to interference as they travel from transmitter to receiver. Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist. Static: Caused by thunderstorms, electrical power lines, electric signs and even traffic lights.

Display screen, heater, air conditioner, audio and phone systems 4-13

SATELLITE RADIO RECEPTION (if so equipped) When the satellite radio is used for the first time or the battery has been replaced, the satellite radio may not work properly. This is not a mal- function. Wait more than 10 minutes with satellite radio ON and the vehicle outside of any metal or large building for satellite radio to receive all of the necessary data. No satellite radio reception is available when the RADIO button is pressed to access satellite radio stations unless optional satellite receiver and an- tenna are installed and an XMT satellite radio service subscription is active. Satellite radio is not available in Alaska, Hawaii and Guam. Satellite radio performance may be affected if cargo carried on the roof blocks the satellite radio signal. If possible, do not put cargo over the satellite antenna. A build up of ice on the satellite radio antenna can affect satellite radio performance. Remove the ice to restore satellite radio reception.

LHA0099
AUDIO OPERATION PRECAUTIONS

Compact disc (CD) player

CAUTION

c Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD player.

c Trying to load a CD with the CD door closed could damage the CD and/or CD player.

c Only one CD can be loaded into the CD

player at a time.

c Only use high quality 4.7 in (12 cm) round discs that have the (cid:147)COMPACT disc DIGITAL AUDIO(cid:148) logo on the disc or packaging.

c During cold weather or rainy days, the player may malfunction due to the hu- midity. If this occurs, remove the CD and dehumidify or ventilate the player completely.

c The player may skip while driving on

rough roads.

c The CD player sometimes cannot func- tion when the compartment tempera- ture low. Decrease/increase the temperature before use.

extremely high or

is

4-14 Display screen, heater, air conditioner, audio and phone systems

c Do not expose the CD to direct sun-

light.

c CDs that are in poor condition or are dirty, scratched or covered with finger- prints may not work properly.

c The following CDs may not work prop-

erly: c Copy control compact discs (CCCD) c Recordable compact discs (CD-R) c Rewritable compact discs (CD-RW) c Do not use the following CDs as they may cause the CD player to malfunc- tion: c 3.1 in (8 cm) discs with an adapter c CDs that are not round c CDs with a paper label c CDs that are warped, scratched, or

have abnormal edges

c This audio system can only play pre- recorded CDs. It has no capability to record or burn CDs.

c If the CD cannot be played, one of the following messages will be displayed.

CHECK DISC: c Confirm that the CD is inserted cor- rectly (the label side is facing up, etc.).

c Confirm that the CD is not bent or

warped and it is free of scratches.

PRESS EJECT:

This is an error due to excessive tem- perature inside the player. Remove the CD by pressing the EJECT button. After a short time, reinsert the CD. The CD can be played when the temperature of the player returns to normal.

UNPLAYABLE:

The file is unplayable in this audio sys- tem (only MP3 or WMA (if so equipped) CD).

Compact Disc with MP3 or WMA (if so equipped) Terms: c MP3 (cid:151) MP3 is short for Moving Pictures Experts Group Audio Layer 3. MP3 is the most well-known compressed digital audio file format. This format allows for near (cid:147)CD quality(cid:148) sound, but at a fraction of the size of normal audio files. MP3 conversion of an audio track from CD-ROM can reduce the file size by approximately a 10:1 ratio with virtually no perceptible loss in quality. MP3
compression removes the redundant and irrelevant parts of a sound signal that the human ear doesn(cid:146)t hear.

c WMA (cid:151) Windows Media Audio (WMA)* is a compressed audio format created by Mi- crosoft as an alternative to MP3. The WMA codec offers greater file compression than the MP3 codec, enabling storage of more digital audio tracks in the same amount of space when compared to MP3s at the same level of quality.

c Bit rate (cid:151) Bit rate denotes the number of bits per second used by a digital music file. The size and quality of a compressed digital audio file is determined by the bit rate used when encoding the file.

Display screen, heater, air conditioner, audio and phone systems 4-15

c If there is a file in the top level of the disc,

(cid:147)Root Folder(cid:148) is displayed.

c The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.

c Sampling frequency (cid:151) Sampling frequency is the rate at which the samples of a signal are converted from analog to digital (A/D conversion) per second.

c Multisession (cid:151) Multisession is one of the methods for writing data to media. Writing data once to the media is called a single session, and writing more than once is called a multisession.

c ID3/WMA Tag (cid:151) The ID3/WMA tag is the part of the encoded MP3 or WMA file that contains information about the digital music file such as song title, artist, encoding bit rate, track time duration, etc. ID3 tag infor- mation is displayed on the Artist/song title line on the display.

* WindowsT and Windows MediaT are regis- tered trademarks and trademarks in the United States of America and other countries of Mi- crosoft Corporation of the USA.

WHA1078

Playback order chart

Playback order: Music playback order of a CD with MP3 or WMA files is as illustrated. c The names of folders not containing MP3 or

WMA files are not shown in the display.

4-16 Display screen, heater, air conditioner, audio and phone systems

Specification chart:

Supported media Supported file systems

Supported versions*1

MP3

WMA

Version Sampling frequency Bit rate Version Sampling frequency Bit rate

Tag information Folder levels Text character number limitation

Displayable character codes*2

CD, CD-R, CD-RW ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. MPEG1, MPEG2, MPEG2.5
8 kHz - 48 kHz 8 kbps - 320 kbps, VBR WMA7, WMA8, WMA9
32 kHz - 48 kHz 48 kbps - 192 kbps, VBR ID3 tag VER1.0, VER1.1, VER2.2, VER2.3 (MP3 only) Folder levels: 8, Max folders: 255 (including root folder), Files: 512 (Max. 255 files for one folder) 128 characters 01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE (UTF-16 Non-BOM Big Endian), 05: UNICODE (UTF-8), 06: UNICODE (Non-UTF-16 BOM Little Endian)

*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.

*2 Available codes depend on what kind of media, versions and information are going to be displayed.

Display screen, heater, air conditioner, audio and phone systems 4-17

Troubleshooting guide:

Symptom

Cannot play

Poor sound quality

It takes a relatively long time before the music starts playing.

Music cuts off or skips

Skipping with high bit rate files Moves immediately to the next song when playing Songs do not play back in the desired order

Cause and Countermeasure

Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player. If there is a temperature increase error, the CD player will play correctly after it returns to the normal temperature. If there is a mixture of music CD files (CD-DA data) and MP3/WMA files on a CD, only the music CD files (CD-DA data) will be played. Files with extensions other than (cid:147).MP3(cid:148),(cid:147).WMA(cid:148), (cid:147).mp3(cid:148) or (cid:147).wma(cid:148) cannot be played. In addition, the character codes and number of characters for folder names and file names should be in compliance with the specifications. Check if the finalization process, such as session close and disc close, is done for the disc. Check if the disc is protected by copyright. Check if the disc is scratched or dirty. Bit rate may be too low. If there are many folders or file levels on the MP3/WMA disc, or if it is a multisession disc, some time may be required before the music starts playing.

The writing software and hardware combination might not match, or the writing speed, writing depth, writing width, etc., might not match the specifications. Try using the slowest writing speed. Skipping may occur with large quantities of data, such as for high bit rate data.

When a non-MP3/WMA file has been given an extension of (cid:147).MP3(cid:148), (cid:147).WMA(cid:148), .(cid:147)mp3(cid:148)or (cid:147).wma(cid:148), or when play is prohibited by copyright protection, there will be approximately 5 seconds of no sound and then the player will skip to the next song. The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.

4-18 Display screen, heater, air conditioner, audio and phone systems

Universal Serial Bus (USB) memory (if so equipped) This system supports various USB memory sticks, USB hard drives and iPodT players. There are some USB devices which may not be sup- ported with this system. c Make sure that the USB device is connected

correctly into the USB connector.

c Do not force the memory stick or USB cable

into the USB connector.

c During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the USB memory stick and dehumidify or ventilate the player com- pletely.

c The player sometimes cannot function when the passenger compartment temperature is extremely high. Decrease the temperature before use.

c Do not leave the USB memory in a place prone to static electricity or where the air conditioner blows directly. The data in the USB memory may be damaged.

c Prepare the USB device by yourself be-

cause it is not equipped with the vehicle.

c The USB device cannot be formatted with this system. If you want to format the USB memory, use your personal computer.

c Partitioned USB devices may not be played

correctly.

c Some characters used in other languages (Chinese, Japanese, etc.) are not displayed properly on the vehicle center screen. NISSAN recommends using English lan- guage characters with USB devices.

c Do not connect the USB device if the con- nector or cable is wet. Allow the cable and/or connectors to dry completely before connecting the USB device.

c Large video podcast files cause slow re- sponses in the iPodT. The vehicle center display may momentarily black out, but it will soon recover.

c If the iPodT automatically selects large video podcast files while in the shuffle mode, the vehicle center display may momentarily black out, but it will soon recover.

c Audiobooks may not play in the same order

as they appear on the iPodT.

c The iPodT nano (1st Generation) may re- main in fast forward or rewind mode if it is connected during a seek operation. In this case, please manually reset the iPodT.

c The iPodT nano (2nd Generation) will con- tinue to fast forward or rewind if it is discon- nected during a seek operation.

c An incorrect song title may appear when the Play Mode is changed while using the iPodT nano (2nd generation).

c If you are using an iPodT (3rd Generation with Dock connector), do not use very long names for the song title, album name or artist name to avoid the iPodT resetting itself.

iPodT is a trademark of Apple Inc., registered in the U.S. and other countries. iPodT* player (if so equipped) c Some characters used in other languages (Chinese, Japanese, etc.) are not displayed properly on the vehicle center screen. We recommend using English language charac- ters with an iPodT.

c Large video podcast files cause slow re- sponses in the iPodT. The vehicle center display may momentarily black out, but it will soon recover.

Display screen, heater, air conditioner, audio and phone systems 4-19

c If the cable is damaged (insulation cut, con- nectors cracked, contamination such as liq- uids, dust, dirt, etc. in the connectors), do not use the cable and contact a NISSAN dealer to replace the cable with a new one. c When not in use for extended periods of time, store the cable in a clean, dust free environment at room temperature and with- out direct sun exposure.

c Do not use the cable for any other purposes

other than its intended use in the vehicle.

*iPodT is a trademark of Apple Inc., registered in the U.S. and other countries.

c If the iPodT automatically selects large video podcast files while in the shuffle mode, the vehicle center display may momentarily black out, but it will soon recover.

c Improperly plugging in the iPodT may cause a checkmark to be displayed on and off (flickering). Always make sure that the iPodT is connected properly.

c The iPodT nano (2nd Generation) will con- tinue to fast forward or rewind if it is discon- nected during a seek operation.

c An incorrect song title may appear when the Play Mode is changed while using the iPodT nano (2nd Generation).

c Audiobooks may not play in the same order

as they appear on the iPodT.

c The iPodT nano (1st Generation) may re- main in fast forward or rewind mode if it is connected during a seek operation. In this case, please manually reset the iPodT.

c If you are using an iPodT (3rd Generation with Dock connector), do not use very long names for the song title, album name or artist name to prevent the iPodT from resetting itself.

c Be careful not to do the following, or the cable could be damaged and a loss of func- tion may occur: c Bend the cable excessively (1.6 in (40

mm) radius maximum).

c Twist the cable excessively (more than

180 degrees).

c Pull or drop the cable. c Close the center console lid on the cable

or connectors.

c Store objects with sharp edges in the

storage where the cable is stored.

c Spill liquids on the cable and connectors. c Do not connect the cable to the iPodT if the It may

cable and/or connectors are wet. damage the iPodT.

c If the cable and connectors are exposed to water, allow the cable and/or connectors to dry completely before connecting the cable to the iPodT (wait 24 hours for it to dry).

c If the connector is exposed to fluids other than water, evaporative residue may cause a short between the connector pins. In this case, replace the cable, otherwise damage to the iPodT and a loss of function may occur.

4-20 Display screen, heater, air conditioner, audio and phone systems

11. VOLUME control knob 12. PWR button 13. SCAN button 14. RDM button 15. Station select (1 - 6) buttons FM/AM RADIO WITH COMPACT DISC (CD) PLAYER (Type A) (if so equipped) For all operation precautions, see 9Audio opera- tion precautions9 in this section. Audio main operation POWER/VOLUME control:

Place the ignition switch in the ACC or ON position. Press the PWR button while the system is off to call up the mode (radio, CD or AUX) that was playing immediately before the system was turned off. While the system is on, pressing the PWR button turns the system off. Turn the VOL control knob to adjust the volume. MENU button (Bass, Treble, Fade, Balance and Clock): Press the MENU button to change the mode as follows: BAS (Bass) ! TRE (Treble) ! FAD (Fade) ! BAL (Balance) ! Clock ! Normal mode

LHA1224

Type A 6. AUX button 7. TUNE button 8. MENU button 9. RPT button 10. AUX IN jack

Display screen, heater, air conditioner, audio and phone systems 4-21

CD eject button

FM-AM button

1. 2. 3. 4. CD button 5. CD insert slot

SEEK button

or

or TUNE

Press the SEEK button to adjust the Bass, Treble, Fade or and Balance to the desired level. Fade adjusts the sound level between the front and rear speak- ers and Balance adjusts the sound between the right and left speakers. Once you have adjusted the sound quality to the desired level, press the MENU button repeatedly until the radio or CD display reappears. If no action is taken, the radio or CD display will auto- matically reappear after approximately 10 sec- onds. Clock set If the clock is not displayed with the ignition switch in the ACC or ON position, you need to select the CLK-ON mode. Press the MENU but- ton repeatedly until CLK-OFF mode is displayed. Use the TUNE/FF-REW/FOLDER button to en- able CLK-ON mode. 1. Press the MENU button repeatedly until (cid:147)Clock:(cid:148) appears. The hours will begin flash- ing.

2. Press the SEEK button

the TUNE button the hours.

or

or to adjust

or

4. Press the SEEK button

the TUNE button the minutes.

or

or to adjust

or

5. Press the MENU button again to exit the

clock set mode.

If no action is taken, the display will return to the regular clock display after 10 seconds. FM/AM radio operation FM•AM button:

Press the FM•AM button to change the band as follows: AM ! FM1 ! FM2 ! AM If another audio source is playing when the FM•AM button is pressed, the audio source play- ing will automatically be turned off and the last radio station played will begin playing.

The FM stereo indicator (ST) illuminates during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception.

TUNE button (Tuning):

3. Press the MENU button again. The minutes

will begin flashing.

Press the TUNE button manual tuning.

or

for

4-22 Display screen, heater, air conditioner, audio and phone systems

SEEK tuning:

Press the SEEK button to tune from low to high or high to low frequencies and to stop at the next broadcasting station. SCAN tuning:

or

Press the SCAN button to stop at each broad- casting station for 5 seconds. Pressing the but- ton again during this 5 second period will stop SCAN tuning and the radio will remain tuned to that station. If the SCAN button is not pressed within 5 seconds, SCAN tuning moves to the next station. 1 to 6 Station memory operations:

Twelve stations can be set for the FM band (6 for FM1, 6 for FM2) and six stations can be set for the AM band.

1. Choose the radio band AM, FM1 or FM2

using the AM•FM select button.

2. Tune to the desired station using manual, SEEK or SCAN tuning. Press and hold any of the desired station memory buttons (1 (cid:150) 6) until a beep sound is heard.

3. The channel indicator will then come on and the sound will resume. Programming is now complete.

4. Other buttons can be set in the same man-

ner.

If the battery cable is disconnected or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. Compact disc (CD) player operation Place the ignition switch in the ACC or ON position and carefully insert the compact disc into the slot with the label side up. The compact disc is automatically pulled into the slot and starts to play. If the radio is already operating, it automatically turns off and the compact disc begins to play. CD button: When the CD button is pressed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play. When the CD button is pressed with a compact disc loaded and the radio playing, the radio will automatically be turned off and the compact disc will start to play.

TUNE (Rewind or Fast Forward) button:

When the TUNE button is pressed while the compact disc is playing, the compact

or

disc plays at an increased speed while reversing or fast forwarding. When the button is released, the compact disc returns to normal play speed.

SEEK button:

When the SEEK button is pressed while the compact disc is playing, the next track follow- ing the present one starts to play from the begin- ning. Press the SEEK button several times to skip several tracks. Each time the button is pressed, the CD advances one additional track. The track number appears in the display window. (When the last track on the compact disc is skipped, the first track is played.)

When the SEEK button is pressed, the track being played returns to the beginning. Press the SEEK button several times to skip back several tracks. Each time the button is pressed the CD moves back one track. RDM button: When the RDM button is pressed while a com- pact disc is playing, the play pattern can be changed as follows: 1 CD RDM ˆ! 1 CD RPT 1 CD RDM: all tracks on the disc will be played randomly. 1 CD RPT: play pattern returns to normal.

RPT button: When the RPT button is pressed while a com- pact disc is playing, the play pattern can be changed as follows: 1 TR RPT ˆ! 1 CD RPT 1 TR RPT: the current track will be repeated. 1 CD RPT: play pattern returns to normal. AUX (Auxiliary) button: The AUX IN jack is located on the front of the radio. The AUX IN audio input jack accepts any standard analog audio input such as from a por- table cassette tape/CD player, MP3 player or a laptop computer. Press the AUX button to play a compatible device when it is plugged into the AUX IN jack.

EJECT button:

When the button is pressed with a com- pact disc loaded, the compact disc will eject and the last source will be played.

When the button is pressed twice with a compact disc loaded, the compact disc will be ejected further for easier CD removal. If the disc is not removed within 15 seconds, the disc will reload.

Display screen, heater, air conditioner, audio and phone systems 4-23

iPod MENU button

11. SCAN/RPT button 12. AUDIO button 13. AUX IN jack 14. Station select (1 - 6) buttons 15. VOLUME control knob 16. PWR button 17. 18. BACK button 19. ENTER button 20. SEEK/TRACK button FM/AM RADIO WITH COMPACT DISC (CD) PLAYER (Type B) (if so equipped) For all operation precautions, see 9Audio opera- tion precautions9 in this section. Audio main operation POWER/VOLUME control:

Place the ignition switch in the ACC or ON position. Press the PWR button while the system is off to call up the mode (radio, CD or AUX) that was playing immediately before the system was turned off. While the system is on, pressing the PWR button turns the system off.

Turn the VOL control knob to adjust the volume.

MUTE button DISP/TEXT button FM-AM button

1. 2. 3. 4. CD button 5. CD insert slot 4-24 Display screen, heater, air conditioner, audio and phone systems

Type B 6. 7. 8. CLOCK button 9. 10. TUNE/FF-REW/FOLDER button

iPod button AUX button

CD eject button

LHA1225

MUTE button:

Press the

button to mute the audio sound.

button again to resume playing

Press the the audio at its previous volume. AUDIO button (Bass, Treble, Fade, Balance, SSV, Beep):

Press the AUDIO button to change the mode as follows: Bass ! Treble ! Fade ! Balance ! Speed Sensitive Volume (SSV) ! Beep ON/OFF ! Normal mode

To adjust Bass, Treble, Fade and Balance, press the AUDIO button until the desired mode ap- pears in the display. Press the TUNE or button to ad- just the selected mode to the desired level. Fade adjusts the sound level between the front and rear speakers and Balance adjusts the sound between the right and left speakers.

or SEEK

or

To change the Beep to ON or OFF, press the TUNE button up or down until the desired mode is displayed. This will enable or disable the beep sound heard during menu selection.

To change the Speed Sensitive Volume (SSV) mode to OFF, LOW, MID or HIGH, press the until the desired TUNE button setting is displayed.

or

Once you have adjusted the sound quality to the desired level, press the AUDIO button repeatedly until the radio or CD display reappears. If no action is taken, the radio or CD display will auto- matically reappear after approximately 5 sec- onds. Clock set

If the clock is not displayed with the ignition switch in the ACC or ON position, you need to select the CLK-ON mode. Press the MENU but- ton repeatedly until CLK-OFF mode is displayed. Use the TUNE/FF-REW/FOLDER button to en- able CLK-ON mode.

1. Press and hold the CLOCK button until the

clock display starts to flash.

2. Press

or

the SEEK/TRACK button to adjust the hours.

3. Press button

the

or

TUNE/FF-REW/FOLDER to adjust the minutes.

4. Press the CLOCK button again to exit the

clock set mode.

If no action is taken, the display will return to the regular clock display after 10 seconds. DISP (display) button This button works during FM, CD and iPodT operation. See the detailed function for this but- ton in the section for each mode. iPODT MENU, ENTER and BACK buttons These buttons can only be used for iPodT opera- tions (if so equipped). See (cid:147)iPodT Player Opera- tion (Type A)(cid:148) later in this section for details about the functions of these buttons. FM/AM radio operation FM•AM button:

Press the FM•AM button to change the band as follows: AM ! FM1 ! FM2 ! AM If another audio source is playing when the FM•AM button is pressed, the audio source play- ing will automatically be turned off and the last radio station played will begin playing.

The FM stereo indicator (ST) illuminates during FM stereo reception. When the stereo broadcast signal is weak, the radio automatically changes from stereo to monaural reception.

Display screen, heater, air conditioner, audio and phone systems 4-25

TUNE button (Tuning):

Press the TUNE/FF-REW/FOLDER button or

for manual tuning.

3. The channel indicator will then come on and the sound will resume. Programming is now complete.

4. Other buttons can be set in the same man-

SEEK tuning:

ner.

or

Press the SEEK/TRACK button to tune from low to high or high to low frequen- cies and to stop at the next broadcasting station. SCAN tuning: Press the SCAN/RPT button to stop at each broadcasting station for 5 seconds. Pressing the button again during this 5 second period will stop SCAN tuning and the radio will remain tuned to that station. the SCAN/RPT button is not pressed within 5 seconds, SCAN tuning moves to the next station. 1 to 6 Station memory operations: Twelve stations can be set for the FM band (6 for FM1, 6 for FM2) and six stations can be set for the AM band. 1. Choose the radio band AM, FM1 or FM2

If

using the AM•FM select button.

2. Tune to the desired station using manual, SEEK or SCAN tuning. Press and hold any of the desired station memory buttons (1 (cid:150) 6) until a beep sound is heard.

If the battery cable is disconnected or if the fuse opens, the radio memory will be canceled. In that case, reset the desired stations. DISP/TEXT button:

When the DISP/TEXT button is pressed while in FM radio mode, the radio display will change as follows: Frequency ! PTY ! PS ! Frequency Compact disc (CD) player operation Place the ignition switch in the ACC or ON position and carefully insert the compact disc into the slot with the label side up. The compact disc is automatically pulled into the slot and starts to play. If the radio is already operating, it automatically turns off and the compact disc begins to play. CD button: When the CD button is pressed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play.

4-26 Display screen, heater, air conditioner, audio and phone systems

When the CD button is pressed with a compact disc loaded and the radio playing, the radio will automatically be turned off and the compact disc will start to play. DISP/TEXT button:

When the DISP/TEXT button is pressed while a CD is playing, the display will change as follows:

CD: Track number ! Disc title ! Song title ! Track number

CD with MP3 or WMA: Track number ! Folder title ! Album title ! Artist ! Song title ! Track number

TUNE/FF-REW/FOLDER (Reverse or Fast Forward) button:

CD:

When the TUNE/FF-REW/FOLDER button (fast forward) or (reverse) is pressed while the compact disc is playing, the compact disc plays at an increased speed while reversing or fast for- warding. When the button is released, the compact disc returns to normal play speed.

CD with MP3 or WMA:

the (fast forward) or

TUNE/FF-REW/FOLDER When button (reverse) is pressed for less than 1.5 seconds while the compact disc is playing, the folders in the CD will change. TUNE/FF-REW/FOLDER When button (reverse) is pressed for more than 1.5 seconds while the compact disc is playing, the compact disc plays at an increased speed while reversing or fast forwarding. When the button is released, the compact disc returns to normal play speed. SEEK/TRACK button:

the (fast forward) or

the SEEK/TRACK button

When is pressed while the compact disc is playing, the next track following the present one starts to play from the beginning. Press the SEEK/TRACK button several times to skip several tracks. Each time the button is pressed, the CD ad- vances one additional track. The track number appears in the display window. (When the last track on the compact disc is skipped, the first track is played.)

the SEEK/TRACK button

When is pressed, the track being played returns to the beginning. SEEK/TRACK

Press

the

AUX (Auxiliary) button: The AUX IN jack is located on the front of the radio. The AUX IN audio input jack accepts any standard analog audio input such as from a por- table cassette tape/CD player, MP3 player or a laptop computer. Press the AUX button to play a compatible device when it is plugged into the AUX IN jack.

EJECT button:

When the button is pressed with a com- pact disc loaded, the compact disc will eject and the last source will be played.

When the button is pressed twice with a compact disc loaded, the compact disc will be ejected further for easier CD removal. If the disc is not removed within 15 seconds, the disc will reload.

several times to skip back several button tracks. Each time the button is pressed the CD moves back one track. SCAN/RPT button:

When the SCAN/RPT button is pressed while a compact disc is playing, the play pattern can be changed as follows:

CD: REPEAT TRACK ! RANDOM TRACK ! RE- PEAT DISC

CD with MP3 or WMA: REPEAT FOLDER ! REPEAT TRACK ! RAN- DOM TRACK ! RANDOM FOLDER ! REPEAT DISC

REPEAT TRACK: the current track will be re- peated.

RANDOM TRACK: all tracks on the disc will be played randomly.

REPEAT DISC: play pattern returns to normal.

REPEAT FOLDER: the current folder will be re- peated.

RANDOM FOLDER: all tracks in the current folder will be played randomly.

Display screen, heater, air conditioner, audio and phone systems 4-27

11. FM-AM button 12. RPT button 13. POWER/VOLUME control knob 14. RDM button

*No satellite radio reception is available when the AUX button is pressed to ac- cess satellite radio stations unless op- tional satellite receiver and antenna are installed and an XMT satellite radio ser- vice subscription is active. Satellite ra- dio is not available in Alaska, Hawaii and Guam.

FM/AM/SAT RADIO WITH COMPACT DISC (CD) PLAYER (if so equipped) For all operation precautions, see 9Audio opera- tion precautions9 in this section. Audio main operation VOL/ON•OFF control:

Place the ignition switch in the ACC or ON position and push the VOL/ON•OFF control knob while the system is off to call up the mode (radio or CD) that was playing immediately before the system was turned off.

LHA1269

6.

TUNE/FOLDER knob/Setting control button SEEK/TRACK buttons AUX IN jack AUX button*

7. 8. 9. 10. CD button

SCAN button Station select (1 - 6) buttons

1. 2. 3. CD insert slot 4. 5.

iPod MENU button

CD eject button

4-28 Display screen, heater, air conditioner, audio and phone systems

To turn the system off, press the VOL/ON•OFF control knob. Turn the VOL/ON•OFF control knob to adjust the volume. This vehicle may be equipped with Speed Sen- sitive Volume (SSV) for audio. When this feature is active, the audio volume changes as the driving speed changes. Setting control knob (Audio, Display and Clock): Press the ENTER button to adjust the audio, display and clock settings as follows: Bass ! Treble ! Fade ! Balance ! Speed Sensitive Volume (SSV) (if so equipped) ! Brightness ! Contrast ! On-screen Clock ! Clock Adjust ! Bass Once the desired setting is displayed on the screen, turn the TUNE/SCROLL knob left or right to adjust the chosen setting. Press the ENTER button to move to the next setting or wait approxi- mately five seconds to exit the setting adjustment mode.

LHA1270

Audio settings: Adjust the bass, treble, fade and balance by selecting the desired setting with the ENTER button and then adjusting the level with the TUNE/SCROLL knob. Balance adjusts the sound between the left and right speakers. Fade adjusts the sound between the front and rear speakers.

LHA1271
Speed Sensitive Volume (if so equipped): To change the Speed Sensitive Volume (SSV) level from 1 to 5, or to turn the feature off entirely, choose the Speed Sensitive Volume (SSV) set- ting with the ENTER button and then adjust the level with the TUNE/SCROLL knob. Speed Sen- sitive Volume (SSV) adjusts the volume of the audio system as the vehicle(cid:146)s driving speed changes.

Display screen, heater, air conditioner, audio and phone systems 4-29

LHA1272

LHA1273

LHA1274

Display settings: To adjust the brightness or contrast of the display screen, press the ENTER button until the chosen setting is displayed. Use the TUNE/SCROLL knob to adjust the display to the desired level.

On-screen Clock: The clock is shown in the upper right corner of the screen. To turn this feature off or to re-enable the clock display after it has been turned off, press the ENTER button until the On-screen Clock mode the TUNE/SCROLL knob to toggle the feature on or off.

displayed.

Use

is

Clock adjust:

To adjust the time, perform the following steps:

1. Press the ENTER button repeatedly until the Clock Adjust mode is displayed on the screen.

2. The hours will begin blinking. Adjust the hours by turning the TUNE/SCROLL knob left or right and press the ENTER button.

3. The minutes will begin blinking. Adjust the minutes by turning the TUNE/SCROLL knob left or right and press the ENTER button.

4-30 Display screen, heater, air conditioner, audio and phone systems

iPodT MENU button This button can only be used for iPodT operations (if so equipped). See (cid:147)iPodT Player Operation (Type B)(cid:148) later in this section for details about the function of this button. FM/AM/SAT radio operation FM•AM button:

Press the FM•AM button to change the band as follows: AM ! FM1 ! FM2 ! AM If another audio source is playing when the FM•AM button is pressed, the audio source play- ing will automatically be turned off and the last radio station played will begin playing.

The FM stereo indicator (STEREO) is shown on the screen during FM stereo reception. When the stereo broadcast signal is weak, the radio auto- matically changes from stereo to monaural re- ception. SAT band select: