Black plate (309,1)
BATTERY REPLACEMENT
CAUTION
Be careful not to allow children to swallow the battery and removed parts.
SDI1753
4.
5.
If the fuse is open *A , replace it with a new fuse *B . If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.
SDI2134
KEYFOB Replace the battery in the keyfob as follows:
1. Remove the screw.
2.
Insert a small screwdriver into the slit of the corner and twist it to separate the upper part
Maintenance and do-it-yourself 8-21
Model "S35-D" EDITED: 2010/ 6/ 4
from the lower part. Use a cloth to protect the casing.
3. Replace the battery with a new one.
Recommended battery:
may cause undesired operation.
Note: Changes or modifications not ex- pressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For Canada:
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: this device may not cause interference, and (2) this device must accept any interfer- ence, including interference that may cause undesired operation of the device.
(1)
CR1620 or equivalent . Do not
touch the internal circuit and electric terminals as doing so could cause a malfunction.
. Hold the battery by the edges. Holding the battery across the contact points will seriously deplete the storage capacity. . Make sure that the + side faces the
bottom case.
4. Close the lid securely and install the screw.
5. Operate the buttons to check its operation.
See a NISSAN dealer if you need any assistance for replacement.
FCC Notice:
For USA:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer- ence received, including interference that
8-22 Maintenance and do-it-yourself
Black plate (310,1)
SDI2451
INTELLIGENT KEY BATTERY Replace the battery in the Intelligent Key as follows:
1. Remove the mechanical key from the In-
telligent Key.
Model "S35-D" EDITED: 2010/ 6/ 4
2.
Insert a small screwdriver into the slit of the corner and twist it to separate the upper part from the lower part. Use a cloth to protect the casing.
3. Replace the battery with a new one.
Recommended battery:
CR2025 or equivalent . Do not
touch the internal circuit and electric terminals as doing so could cause a malfunction.
. Hold the battery by the edges. Holding the battery across the contact points will seriously deplete the storage capacity. . Make sure that the + side faces the
bottom case.
SDI2452
4. Align the tips of the upper and lower parts *1 , and then push them together *2 until it is securely closed.
5. Operate the buttons to check its operation.
See a NISSAN dealer if you need any assistance for replacement.
FCC Notice:
For USA:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer-
Black plate (311,1)
ence received, including interference that may cause undesired operation.
Note: Changes or modifications not ex- pressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For Canada:
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: this device may not cause interference, and (2) this device must accept any interfer- ence, including interference that may cause undesired operation of the device.
(1)
Maintenance and do-it-yourself 8-23
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (312,1)
LIGHTS
Front fog light
Front turn signal/park/side marker light Front map light
1. Headlight (high-beam) 2. 3. 4. Ceiling light 5. 6. Headlight (low-beam) 7. High-mounted stop light 8. Cargo light 9. 10. Back-up light 11. Rear combination light (stop/tail/side marker light) 12. Rear turn signal light
License plate light
8-24 Maintenance and do-it-yourself
SDI2668
Model "S35-D" EDITED: 2010/ 6/ 4
HEADLIGHTS Fog may temporarily form inside the lens of the exterior lights in the rain or in a car wash. A temperature difference between the inside and the outside of the lens causes the fog. This is not a malfunction. If large drops of water collect inside the lens, contact a NISSAN dealer.
Replacing
Xenon headlight model:
WARNING
HIGH VOLTAGE
When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xe- non headlights replaced at a NISSAN dealer. For additional information, see “HEADLIGHT AND TURN SIGNAL SWITCH” in the “2. Instruments and controls” section.
If replacement is required, see a NISSAN dealer.
Use the same number and wattage as originally installed:
Low beam:
Wattage: 35
Bulb no.: D2R
High beam:
Wattage: 60
Bulb no.: HB3
Halogen headlight model:
The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb.
CAUTION
. Do not leave the bulb out of the headlight reflector for a long period of time. Dust, moisture, smoke, etc. entering the headlight body may affect bulb performance.
. High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.
. Only touch the plastic base when handling the bulb. Never touch the glass envelope.
. Aiming is not necessary after repla- cing the bulb. When aiming adjust-
Black plate (313,1)
is necessary, contact a
ment NISSAN dealer.
Use the same number and wattage as originally installed:
Low beam:
Wattage: 55
Bulb no.: H11
High beam:
Wattage: 60
Bulb no.: HB3
Maintenance and do-it-yourself 8-25
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (314,1)
EXTERIOR AND INTERIOR LIGHTS
Item
Wattage (W)
Front turn signal/parking/side marker light Front fog light (if so equipped)
Rear combination light
back-up turn signal stop/tail/side marker
License plate light Front map light Vanity mirror light (if so equipped) High-mounted stop light* Ceiling light (if so equipped) Cargo light
Glove box light*
27/8
35
18
21
21/5
LED
3.4
Bulb No.
S25
H8
W16W W21W W21/5W
W5W
— — — — —
—
*: See a NISSAN dealer for replacement. NOTE: Always check with the Parts Department at a NISSAN dealer for the latest information about parts.
Model "S35-D" EDITED: 2010/ 6/ 4
SDI2137
Disconnect the battery negative cable before replacing bulbs. *A High-beam bulb *B Low-beam bulb
8-26 Maintenance and do-it-yourself
Black plate (315,1)
SDI2141
Front turn signal/park/side marker light
(Halogen headlight model)
Xenon headlight model: See a NISSAN dealer for replacement.
Halogen headlight model: Remove the bulb as illustrated.
SDI2306
: REMOVE
INSTALL
Replacement procedures All other lights are either type A, B, C, D or E. When replacing a bulb, first remove the lens and/or cover.
Front fog light
SDI2170
Maintenance and do-it-yourself 8-27
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (316,1)
SDI2138
Rear combination light (stop/tail/side marker/turn)
Open the lift gate to remove the rear combina- tion light assembly. *A : Clip
Back-up light
Open the lift gate to remove the back-up light assembly. One screw is located behind the cover on the lift gate.
License plate light
The license plate light bulb can be accessed by removing the cover on the inside of the lift gate.
SDI2139
SDI2140
8-28 Maintenance and do-it-yourself
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (317,1)
WHEELS AND TIRES
If you have a flat tire, see “FLAT TIRE” in the “6. In case of emergency” section.
TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit and the CHECK TIRE PRESSURE warning (if so equipped) appears on the vehicle information display, one or more of your tires is significantly under-inflated.
The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving).
For more details, see “Low tire pressure warning light” in the “2. Instruments and controls” section, “TIRE PRESSURE MONITORING SYS- TEM (TPMS)” in the “5. Starting and driving” section and “TIRE PRESSURE MONITORING SYSTEM (TPMS)” in the “6. In case of emergency” section.
Tire inflation pressure Check the pressure of the tires (including the spare) often and always prior to long distance trips. The recommended tire
Maintenance and do-it-yourself 8-29
Model "S35-D" EDITED: 2010/ 6/ 4
Front map light
Cargo light
SDI2030
SDI1500B
Ceiling light
Vanity mirror light
SDI1499A
SDI2032
pressure specifications are shown on the Tire and Loading Information label under the “Cold Tire Pressure” heading. The Tire and Loading Information label is affixed to the driver side center pillar. Tire pressures should be checked regularly because: . Most tires naturally lose air over time. . Tires can lose air suddenly when driven over potholes or other objects or if the vehicle strikes a curb while parking.
The tire pressures should be checked when the tires are cold. The tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds.
Incorrect tire pressure, including un- der inflation, may adversely affect tire life and vehicle handling.
WARNING
Improperly inflated tires can fail suddenly and cause an accident. . The Gross Vehicle Weight rating (GVWR) is located on the F.M.V. S.S./C.M.V.S.S. certification la-
8-30 Maintenance and do-it-yourself
bel. The vehicle weight capacity is indicated on the Tire and Loading Information label. Do not load your vehicle beyond this capacity. Overloading your vehicle may result in reduced tire life, unsafe operating condi- tions due to premature tire fail- ure, or unfavorable handling characteristics and could also lead to a serious accident. Load- ing beyond the specified capa- city may also result in failure of other vehicle components.
. Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level.
. For additional
information re- garding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Cana- da) in the Warranty Information Booklet.
Black plate (318,1)
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (319,1)
*3 Original size: The size of the tires originally installed on the vehicle at the factory.
*4 Cold tire pressure: Inflate the tires to this pressure when the tires are cold. Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds. The recommended cold tire inflation is set by the manufacturer to provide the best balance of tire wear, vehicle handling, driveability, tire noise, etc., up to the vehicle’s GVWR.
*5 Tire size — see “TIRE LABELING”
later in this section.
*6 Spare tire size or compact spare tire
SDI2340
size (if so equipped)
Tire and Loading Information label *1 Seating capacity: The maximum num- ber of occupants that can be seated in the vehicle.
*2 Vehicle load limit: See “VEHICLE LOADING INFORMATION” in the “9. Technical and consumer information” section.
Maintenance and do-it-yourself 8-31
Model "S35-D" EDITED: 2010/ 6/ 4
tion shown on the Tire and Loading Information label.
5. Add air to the tire as needed.
If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Re- check the pressure and add or release air as needed.
6.
Install the valve stem cap.
7. Check the pressure of all other tires,
including the spare.
SIZE
P215/70- R16 99H P225/60- R17 98H
P225/55- R18 97V
COLD TIRE
INFLATION
PRESSURE
230 kPa,
33 PSI
230 kPa,
33 PSI
230 kPa,
33 PSI*1
260 kPa,
38 PSI*2
FRONT
ORIGINAL
TIRE
SDI1949
Checking the tire pressure 1. Remove the valve stem cap from the
tire.
2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem sideways, or air will escape. the hissing sound of air escaping from the tire is heard while checking the pressure, reposition the gauge to eliminate this leakage.
If
3. Remove the gauge.
4. Read the tire pressure on the gauge stem and compare it to the specifica-
8-32 Maintenance and do-it-yourself
Black plate (320,1)
REAR
ORIGINAL
TIRE
P215/70- R16 99H P225/60- R17 98H
P225/55- R18 97V
SPARE
TIRE
Original tire
T155/90-
D16
*1: 2WD *2: AWD
230 kPa,
33 PSI
230 kPa,
33 PSI
230 kPa,
33 PSI*1
260 kPa,
38 PSI*2
230 kPa,
33 PSI*1
260 kPa,
38 PSI*2
420 kPa,
60 PSI
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (321,1)
5. Two-digit number (16): This number is
the wheel or rim diameter in inches.
6. Two- or three-digit number (94): This number is the tire’s load index. It is a measurement of how much weight each tire can support. You may not find this information on all tires because it is not required by law.
7. H: Tire speed rating. You should not drive the vehicle faster than the tire speed rating.
Maintenance and do-it-yourself 8-33
Model "S35-D" EDITED: 2010/ 6/ 4
TIRE LABELING
Example
SDI1575
SDI1606
*1 Tire size (example: P215/60R16
Example
Federal law requires tire manufacturers to place standardized information on the side- wall of all tires. This information identifies and describes the fundamental character- istics of the tire and also provides the tire identification number (TIN) for safety stan- dard certification. The TIN can be used to identify the tire in case of a recall.
94H)
1. P: The “P” indicates the tire is designed tires
for passenger vehicles. (Not all have this information.)
2. Three-digit number (215): This number gives the width in millimeters of the tire from sidewall edge to sidewall edge.
3. Two-digit number (60): This number, known as the aspect ratio, gives the tire’s ratio of height to width.
4. R: The “R” stands for radial.
5. Three-digit code: Date of Manufacture
6. Four numbers represent the week and year the tire was built. For example, the numbers 3103 means the 31st week of 2003. If these numbers are missing, then look on the other sidewall of the tire.
*3 Tire ply composition and material
layers or plies of
The number of rubber-coated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others.
*4 Maximum permissible inflation pres-
sure This number is the greatest amount of air pressure that should be put in the tire. Do not exceed the maximum permissible inflation pressure.
*5 Maximum load rating
This number indicates the maximum load in kilograms and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same
SDI1607
Example
*2 TIN (Tire Identification Number) for a new tire (example: DOT XX XX XXX XXXX)
1. DOT: Abbreviation for the “Department of Transportation”. The symbol can be placed above, below or to the left or right of the Tire Identification Number.
2. Two-digit code: Manufacturer’s identifi-
cation mark
3. Two-digit code: Tire size
4. Three-digit code: Tire type code (Op-
tional)
8-34 Maintenance and do-it-yourself
Black plate (322,1)
load rating as the factory installed tire.
*6 Term of “tubeless” or “tube type”
Indicates whether the tire requires an inner tube (“tube type”) or not (“tubeless”).
*7 The word “radial”
The word “radial” is shown, if the tire has radial structure.
*8 Manufacturer or brand name
Manufacturer or brand name is shown.
Other tire-related terminology:
In addition to the many terms that are defined throughout this section, Intended Outboard Sidewall is (1) the sidewall that contains a whitewall, bears white lettering or bears manufacturer, brand and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (2) the outward facing sidewall of an asymmetrical tire that has a particular side that must always face outward when mounted on a vehicle.
Model "S35-D" EDITED: 2010/ 6/ 4
TYPES OF TIRES
WARNING
. When changing or replacing tires, be sure all four tires are of the same type (Example: Summer, All Season or Snow) and construction. A NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability.
. Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire.
. Replacing tires with those not ori- ginally specified by NISSAN could affect the proper operation of the TPMS.
. For additional information regard- ing tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet.
All season tires NISSAN specifies all season tires on some models to provide good performance all year, including snowy and icy road conditions. All Season tires are identified by ALL SEASON and/or M&S (Mud and Snow) on the tire sidewall. Snow tires have better snow traction than All Season tires and may be more appro- priate in some areas.
Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially reduced in snow and ice. Summer tires do not have the tire traction rating M&S on the tire sidewall.
If you plan to operate your vehicle in snowy or icy conditions, NISSAN recommends the use of SNOW tires or ALL SEASON tires on all four wheels.
Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. it can adversely affect the safety and handling of your vehicle.
If you do not,
Generally, snow tires will have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed.
Black plate (323,1)
Never exceed the maximum speed rating of the tire.
If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels.
For additional traction on icy roads, studded tires may be used. However, some U.S. states their use. and Canadian provinces prohibit Check local, state and provincial laws before installing studded tires. Skid and traction cap- abilities of studded snow tires, on wet or dry surfaces, may be poorer than that of non- studded snow tires.
All-Wheel Drive (AWD) models
CAUTION
. Always use tires of the same type, size, brand, construction (bias, bias- belted or radial), and tread pattern on all four wheels. Failure to do so may result in a circumference differ- ence between tires on the front and rear axles which will cause exces- sive tire wear and may damage the transmission, transfer case and dif- ferential gears.
Maintenance and do-it-yourself 8-35
Model "S35-D" EDITED: 2010/ 6/ 4
. ONLY use spare tires specified for
the AWD model.
it
If excessive tire wear is found, is recom- mended that all four tires be replaced with tires of the same size, brand, construction and tread pattern. The tire pressure and wheel alignment should also be checked and corrected as necessary. Contact a NISSAN dealer.
TIRE CHAINS
CAUTION
NISSAN recommends using the follow- ing tire cables made by Peerless Chain Company for this vehicle due to limited tire clearance. Call 800-533-8056 to order tire chains for your vehicle.
215/70R16 - Sno-trac1000 part num-
ber 0103855 with chain tightener
part number 2007020
225/60R17, 225/55R18 - Sno-
trac1000 part number 0103855 with
c h a i n ti g h t e n er p a r t n u m b e r
2007190
traction Failure to use the correct device will cause damage to the brakes, suspension or other vehicle parts.
8-36 Maintenance and do-it-yourself
The tire chain part numbers and Peerless Chain Company phone number are correct at the time of printing that is shown on the back cover of this Owner’s Manual. Always confirm the correct part numbers with Peerless Chain Company before ordering.
Only use other types of traction devices if the traction device manufacturer recommends it for use on your specific vehicle and the tire and wheel installed on your vehicle.
traction devices may be prohibited Use of according to location. Check the local laws before installing traction devices. When instal- ling traction devices, make sure they are the proper size for the tires on your vehicle and are installed according to the traction device man- ufacturer’s suggestions. When using traction devices, avoid fully loading your vehicle and drive at reduced speeds. Failure to do so may cause damage to the brakes and suspension and adversely affect handling and performance.
Traction devices must be installed only on the front wheels and not on the rear wheels.
Do not drive with traction devices on paved roads that are clear of snow. Driving with traction devices in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress.
Black plate (324,1)
CAUTION
. Do not use traction devices on dry
roads.
. Never install traction devices on a T- type spare tire as doing so could damage the brakes, suspension or other vehicle parts.
Model "S35-D" EDITED: 2010/ 6/ 4
Wheel nut tightening torque:
80 ft-lb (108 N·m)
The wheel nuts must be kept tigh- tened to the specification at all times. It is recommended that wheel nuts be tightened to the specification at each tire rotation interval.
WARNING
. After rotating the tires, check
and adjust the tire pressure.
. Retighten the wheel nuts when the vehicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).
. Do not include the spare tire or any other small size spare tire in the tire rotation.
. For additional
information re- garding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Cana- da) in the Warranty Information Booklet.
SDI1662
CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km). (See “FLAT TIRE” in the “6. In case of emergency” section for tire replacing procedures.)
As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench.
Black plate (325,1)
SDI1663
1. Wear indicator 2. Wear indicator location mark Tire wear and damage
WARNING
. Tires should be periodically in- spected for wear, cracking, bul- ging or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found, the tire(s) should be replaced.
. The original tires have built-in tread wear indicators. When
Maintenance and do-it-yourself 8-37
Model "S35-D" EDITED: 2010/ 6/ 4
.
WARNING
The use of tires other than those recommended or the mixed use of tires of different brands, construc- tion (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-to-tire clearance, tire chain clearance, speedometer calibration, headlight aim and bum- per height. Some of these effects may lead to accidents and could result in serious personal injury.
If the wheels are changed for any reason, always replace with wheels which have the same off-set dimen- sion. Wheels of a different off-set could cause premature tire wear, degrade vehicle handling character- istics and/or interference with the brake discs/drums. Such interfer- ence can lead to decreased braking efficiency and/or early brake pad/ shoe wear. See “WHEELS AND TIRES” in the “9. Technical and consumer information” section of this manual for wheel off-set dimen- sions.
Black plate (326,1)
. When a spare tire is mounted or a wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approxi- mately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/ or system resetting.
. Replacing tires with those not ori- ginally specified by NISSAN could affect the proper operation of the TPMS.
. Do not install a damaged or de- formed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warning.
The use of retread tire is not re- commended.
. For additional information regard- ing tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet.
Model "S35-D" EDITED: 2010/ 6/ 4
wear indicators are visible, the tire(s) should be replaced.
. Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified technician, because some tire damage may not be obvious. Replace the tires as necessary to prevent tire failure and possible personal injury. Improper service of the spare tire may result in serious perso- nal injury. If it is necessary to repair the spare tire, contact a NISSAN dealer. . For additional
information re- garding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Cana- da) in the Warranty Information Booklet.
Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. (See “SPECIFICA- TIONS” in the “9. Technical and consumer information” section for recommended types and sizes of tires and wheels.) 8-38 Maintenance and do-it-yourself
CAUTION
Always use tires of the same type, size, brand, construction (bias, bias-belted or radial), and tread pattern on all four wheels. Failure to do so may result in a circumference difference between tires on the front and rear axles which will cause excessive tire wear and may damage the transmission, transfer case and differential gears (AWD models).
Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as required.
Wheel balance service should be per- formed with the wheels off the vehicle. Spin balancing the wheels on the vehicle could lead to mechanical damage.
For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the War- ranty Information Booklet.
Care of wheels See “CLEANING EXTERIOR” in the “7. Ap- pearance and care” section for details about
care of the wheels.
Spare tire When a spare tire is mounted (TEMPORARY USE ONLY or conventional), the TPMS will not function.
Observe the following precautions if the TEM- PORARY USE ONLY spare tire must be used, otherwise your vehicle could be damaged or involved in an accident.
WARNING
The TEMPORARY USE ONLY spare tire should be used for emergency use. It should be replaced with the standard tire at the first opportunity to avoid possible tire or differential damage.
. Drive carefully while the TEMPOR- ARY USE ONLY spare tire is in- stalled. Avoid sharp turns and abrupt braking while driving.
. Periodically check spare tire infla- tion pressure. Always keep the pressure of the TEMPORARY USE ONLY spare tire at 60 psi (420 kPa, 4.2 bar). Always keep the pressure of the full size spare tire (if so
Black plate (327,1)
equipped) at the recommended pressure for standard tires, as in- dicated on the Tire and Loading Information label.
. With the TEMPORARY USE ONLY
spare tire installed do not drive your
vehicle at speeds faster than 50
MPH (80 km/h).
. When driving on roads covered with snow or ice, the TEMPORARY USE ONLY spare tire should be used on the rear wheels and original tire used on the front wheels (drive wheels). Use tire chains only on the front (original) tires.
Tire tread of the TEMPORARY USE ONLY spare tire will wear at a faster rate than the standard tire. Replace the spare tire as soon as the tread wear indicators appear.
. Do not use the spare tire on other
vehicles.
. Do not use more than one spare tire
at the same time.
. Do not
tow a trailer while the TEMPORARY USE ONLY spare tire is installed.
Maintenance and do-it-yourself 8-39
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (328,1)
CAUTION
. Do not use tire chains on a TEM- PORARY USE ONLY spare tire. Tire chains will not fit properly and may cause damage to the vehicle.
. Because the TEMPORARY USE ONLY spare tire is smaller than the original tire, ground clearance is reduced. To avoid damage to the vehicle, do not drive over obstacles. Also do not drive the vehicle through an automatic car wash since it may get caught.
8-40 Maintenance and do-it-yourself
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (329,1)
MEMO
Maintenance and do-it-yourself 8-41
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (330,1)
MEMO
8-42 Maintenance and do-it-yourself
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (28,1)
9 Technical and consumer information
Capacities and recommended fuel/lubricants . . . . . . . . . . . . 9-2
Fuel recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Engine oil and oil filter recommendation. . . . . . . . . . . . . . . 9-5
Air conditioning system refrigerant and lubricant
recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Wheels and tires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Dimensions and weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
When traveling or registering your vehicle in
another country. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Vehicle identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Vehicle Identification Number (VIN) plate . . . . . . . . . . . . . 9-8
Vehicle identification number (chassis number). . . . . . 9-9
Engine serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
F.M.V.S.S./C.M.V.S.S. certification label . . . . . . . . . . . . . . . 9-9
Emission control information label . . . . . . . . . . . . . . . . . . . . 9-10
Tire and loading information label. . . . . . . . . . . . . . . . . . . . . 9-10
Air conditioner specification label . . . . . . . . . . . . . . . . . . . . . 9-10
Installing front license plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Except for Kro¯ m models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
For Kro¯ m models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Vehicle loading information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13
Vehicle load capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14
Securing the load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16
Loading tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17
Measurement of weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-17
Towing a trailer (except for Kro¯ m models) . . . . . . . . . . . . . . 9-17
Maximum load limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-18
Maximum Gross Vehicle Weight (GVW)/
maximum Gross Axle Weight (GAW) . . . . . . . . . . . . . . . . 9-19
Towing load/specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-21
Towing safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22
Flat towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-25
Uniform tire quality grading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26
Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26
Traction AA, A, B and C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26
Temperature A, B and C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26
Emission control system warranty. . . . . . . . . . . . . . . . . . . . . . . . . 9-27
Reporting safety defects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-27
Readiness for Inspection/Maintenance (I/M) test. . . . . . 9-28
Event Data Recorders (EDR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-29
Owner’s Manual/Service Manual order information . . . 9-30
In the event of a collision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-30
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (332,1)
CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS
The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure instructed in the “8. Maintenance and do-it-yourself” section to determine the proper refill capacity.
Capacity (Approximate)
Recommended specifications
Fuel
Engine oil*1
Drain and refill
With oil filter change
Without oil filter change
Cooling system
With reservoir
Reservoir
Continuously Variable Transmission (CVT) fluid
Differential gear oil
Transfer oil
Brake fluid
Multi-purpose grease Air conditioning system refrigerant Air conditioning system lubricants Window washer fluid
US measure
Imp measure
15-7/8 gal
13-1/4 gal
4-7/8 qt
4-1/2 qt
7-3/4 qt
3/4 qt
—
—
—
4 qt
3-3/4 qt
6-3/8 qt
5/8 qt
—
—
—
Liter
60
4.6
4.3
7.3
0.75
—
—
—
See “FUEL RECOMMENDATION” later in this section.
. Engine oil with API Certification Mark*2
. Viscosity SAE 5W-30
Pre-diluted Genuine NISSAN Long Life Antifreeze/Coolant (blue) or equivalent
Genuine NISSAN CVT Fluid NS-2*3
Genuine NISSAN Differential Oil Hypoid Super GL-5 80W-90 or API GL-5 Viscosity SAE
80W-90*4
Genuine NISSAN Differential Oil Hypoid Super GL-5 80W-90 or API GL-5 Viscosity SAE
80W-90
Refill to the proper oil level according to the instructions in the “8. Maintenance and do-it-yourself” section.
Genuine NISSAN Super Heavy Duty Brake Fluid*5 or equivalent DOT 3
— — —
1-1/4 gal
— — —
1 gal
—
—
—
4.5
NLGI No. 2 (Lithium soap base)
HFC-134a (R-134a)*6
NISSAN A/C System Oil Type S or exact equivalent
Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or equivalent
For additional information, see “ENGINE OIL” in the “8. Maintenance and do-it-yourself” section for changing engine oil. For additional information, see “ENGINE OIL AND OIL FILTER RECOMMENDATION” later in this section.
*1: *2: *3: Use only Genuine NISSAN CVT Fluid NS-2. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-2 will damage the CVT, which is not covered by the NISSAN new vehicle
limited warranty. For hot climates, viscosity SAE 90 is suitable for ambient temperatures above 328F (08C).
*4: *5: Available in mainland U.S.A. through a NISSAN dealer. *6:
For additional information, see “VEHICLE IDENTIFICATION” later in this section for air conditioner specification label.
9-2 Technical and consumer information
Model "S35-D" EDITED: 2010/ 6/ 4
FUEL RECOMMENDATION Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91).
CAUTION
. Using a fuel other than that speci- fied could adversely affect the emis- sion control system, and may also affect warranty coverage.
. Under no circumstances should a leaded gasoline be used, because this will damage the three-way cat- alyst.
. Do not use E-85 fuel in your vehicle. Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel can damage the fuel system compo- nents and is not covered by the NISSAN new vehicle limited war- ranty.
Gasoline specifications NISSAN recommends using gasoline that meets the World-Wide Fuel Charter (WWFC) speci- fications where it the automobile manufacturers developed this spe- cification to improve emission control system
is available. Many of
and vehicle performance. Ask your service station manager the gasoline meets the WWFC specifications.
if
Reformulated gasoline Some fuel suppliers are now producing refor- mulated gasolines. These gasolines are specially designed to reduce vehicle emissions. NISSAN supports efforts towards cleaner air and sug- gests that you use reformulated gasoline when available.
Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxygenates such as ethanol, MTBE and metha- nol with or without advertising their presence. NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel compatibility for your NISSAN cannot be readily determined. If in doubt, ask your service station manager.
If you use oxygenate-blend gasoline, please take the following precautions as the usage of such fuels may cause vehicle performance problems and/or fuel system damage.
The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline.
If an oxygenate-blend, other than methanol blend is used, it should contain no more than 10% oxygenate.
Black plate (333,1)
(MTBE may, however, be added up to 15%.)
If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol) . It should also contain a suitable amount of appropriate cosolvents and corro- sion inhibitors. If not properly formu- lated with appropriate cosolvents and corrosion inhibitors, such methanol blends may cause fuel system damage and/or vehicle performance problems. At this time, sufficient data is not available to ensure that all methanol blends are suitable for use in NISSAN vehicles.
If any driveability problems such as engine stalling and difficult hot-starting are experienced after using oxygenate-blend fuels, immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE.
Take care not to spill gasoline during refueling. Gasoline containing oxygenates can cause paint damage.
E-85 fuel
E-85 fuel is a mixture of approximately 85% fuel
ethanol and 15% unleaded gasoline. E-85 can
only be used in a Flexible Fuel Vehicle (FFV). Do
not use E-85 fuel in your vehicle. U.S. govern-
ment regulations require fuel ethanol dispensing
Technical and consumer information 9-3
Model "S35-D" EDITED: 2010/ 6/ 4
If any of
damage. the above symptoms are encountered, have your vehicle checked at a NISSAN dealer.
However, now and then you may notice light spark knock for a short time while accelerating or driving up hills. This is not a cause for concern, because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load.
CAUTION
. Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel in a vehicle not specifically designed for E-85 fuel can damage fuel system components and is not covered by the NISSAN new vehicle limited warranty.
. E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline.
. U.S. government regulations require ethanol dispensing pumps to be identified by a small, square, orange and black label with the common abbreviation or the appropriate per- centage for that region.
Black plate (334,1)
Model "S35-D" EDITED: 2010/ 6/ 4
pumps to be identified by a small, square, orange and black label with the common abbreviation or the appropriate percentage for that region.
fuel additives (for example,
Aftermarket fuel additives NISSAN does not recommend the use of any aftermarket fuel injector cleaner, octane booster, intake valve deposit removers, etc.) which are sold commer- cially. Many of these additives intended for gum, varnish or deposit removal may contain active solvent or similar ingredients that can be harmful to the fuel system and engine.
Octane rating tips Using unleaded gasoline with an octane rating lower than recommended can cause persistent, heavy “spark knock”. (Spark knock is a metallic rapping noise.) If severe, this can lead to engine damage. If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating, or if you hear steady spark knock while holding a steady speed on level roads, have a NISSAN dealer correct the condition. Failure to correct the condi- tion is misuse of the vehicle, for which NISSAN is not responsible.
ignition timing will
Incorrect in spark knock, after-run and/or overheating, which may cause excessive fuel consumption or engine 9-4 Technical and consumer information
result
Black plate (335,1)
Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be operated before the next oil change. Choosing an oil viscosity other than that recommended could cause serious engine damage.
Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high-quality genuine NISSAN oil filter. When replacing, use a genuine NISSAN oil filter or its equivalent for the reason described in “Change intervals”.
Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Using an engine oil and filter other than the specified quality, or exceed- ing recommended oil and filter change intervals could reduce engine life. Damage to the engine caused by improper maintenance or use of incorrect oil and filter quality and/or viscosity is not covered by the NISSAN new vehicle limited warranty.
Your engine was filled with a high quality engine oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend
Technical and consumer information 9-5
Model "S35-D" EDITED: 2010/ 6/ 4
1. API certification mark 2. API service symbol ENGINE OIL AND OIL FILTER RE- COMMENDATION Selecting the correct oil It to choose the correct grade, quality, and viscosity engine oil to ensure satisfactory engine life and performance, see “CAPACITIES AND RECOMMENDED FUEL/ LUBRICANTS” earlier in this section. NISSAN recommends the use of an energy conserving oil in order to improve fuel economy.
is essential
Select only engine oils that meet the American Petroleum Institute (API) certification or Interna-
STI0505
tional Lubricant Standardization and Approval Committee (ILSAC) certification and SAE vis- cosity standard. These oils have the API certification mark on the front of the container. Oils which do not have the specified quality label should not be used as they could cause engine damage.
Oil additives NISSAN does not recommend the use of oil additives. The use of an oil additive is not necessary when the proper oil type is used and maintenance intervals are followed.
Oil which may contain foreign matter or has been previously used should not be used.
upon how you use your vehicle.
system components.
The refrigerant HFC-134a (R-134a) in your NISSAN vehicle will not harm the earth’s ozone layer. Although this refrigerant does not affect the earth’s atmosphere, certain governmental regulations require the recovery and recycling of any refrigerant during automotive air condition- ing system service. A NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioning system refrigerant.
Contact a NISSAN dealer when servicing your air conditioning system.
Operation under the following conditions may require more frequent oil and filter changes.
repeated short distance driving at cold outside temperatures
driving in dusty conditions
extensive idling
towing a trailer
stop and go commuting
Refer to the “NISSAN Service and Maintenance Guide” for the maintenance schedule.
AIR CONDITIONING SYSTEM RE- FRIGERANT AND LUBRICANT RE- COMMENDATIONS The air conditioning system in your NISSAN vehicle must be charged with the refrigerant HFC-134a (R-134a) and the oil, NISSAN A/C system oil Type S or the exact equivalents.
CAUTION
The use of any other refrigerant or oil will cause severe damage to the air conditioning system and will require the replacement of all air conditioner
9-6 Technical and consumer information
Black plate (336,1)
Model "S35-D" EDITED: 2010/ 6/ 4
SPECIFICATIONS
ENGINE
Model
Type Cylinder arrangement Bore 6 Stroke Displacement Firing order
Idle speed Ignition timing (B.T.D.C.)
Spark plug
Spark plug gap (Normal)
Camshaft operation
QR25DE
Gasoline, 4-cycle, DOHC
4-cylinder, in-line
3.5 6 3.9 (89.0 6 100.0)
151.82 (2,488)
1-3-4-2
No adjustment is necessary.
DILKAR6A-11
0.043 (1.1)
Timing chain
in (mm) cu in (cm3)
rpm degree/rpm
Standard
in (mm)
This spark ignition system complies with the Canadian standard ICES-002.
Black plate (337,1)
WHEELS AND TIRES Road wheel
Type
Conventional
Spare
Tire
Type
Conventional
Spare
Size 16 6 6-1/2JJ 17 6 7J 18 6 7J Conventional 16 6 4T
Offset in (mm)
1.57 (40)
1.57 (40)
1.18 (30)
Size
P215/70R16
99H
P225/60R17
98H
P225/55R18
97V
T155/90D16
Conventional
Pressure PSI (kPa) [Cold]
33 (230)
33 (230)*1
38 (260)*2
60 (420)
33 (230)
38 (260)*3
*1: 2WD *2: AWD *3: AWD (P225/55R18 97V)
Technical and consumer information 9-7
Model "S35-D" EDITED: 2010/ 6/ 4
WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY
When planning to travel in another coun- try, you should first find out if the fuel available is suitable for your vehicle’s engine.
Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. Therefore, avoid taking your vehicle to areas where appropriate fuel is not available.
When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations.
The laws and regulations for motor vehicle emission control and safety standards vary according to the country, state, province or district; therefore, vehicle specifications may differ.
When any vehicle is to be taken into another country, state, province or district and registered, its modifications, transpor- tation, and registration are the responsi- bility of the user. NISSAN is not responsible for any inconvenience that may result.
DIMENSIONS AND WEIGHTS
Overall length
in (mm) 183.3 (4,655)*1
183.9 (4,670)*2
184.3 (4,680)*1, *3
184.4 (4,685)*2, *3
Overall width Overall height
in (mm) 70.9 (1,800) in (mm) 65.3 (1,658)
Front tread Rear tread Wheelbase
Gross Vehicle Weight Rating (GVWR) Gross Axle Weight Rating (GAWR)
Front
Rear
66.3 (1,683)*4
in (mm) 60.6 (1,540) in (mm) 61.0 (1,550) in (mm) 105.9 (2,690)
lb (kg)
lb (kg)
lb (kg)
See the F.M.V.S.S. or C.M.V.S.S. certification label on the driver’s side center pillar.
*1: Without front license plate bracket *2: With front license plate bracket *3: Kro¯ m models *4: With roof rail
9-8 Technical and consumer information
Black plate (338,1)
VEHICLE IDENTIFICATION
STI0457
VEHICLE IDENTIFICATION NUMBER (VIN) PLATE The vehicle identification number plate is at- tached as shown. This number is the identifica- tion for your vehicle and is used in the vehicle registration.
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (339,1)
STI0553
SDI2121
STI0448
VEHICLE IDENTIFICATION NUMBER (chassis number) The vehicle identification number is located as shown.
Remove the cover to access the number.
ENGINE SERIAL NUMBER The number is stamped on the engine as shown.
F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL The Federal/Canadian Motor Vehicle Safety Standards (F.M.V.S.S./C.M.V.S.S.) certification label is affixed as shown. This label contains valuable vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Number (VIN), etc. Review it carefully.
Technical and consumer information 9-9
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (340,1)
STI0554
STI0494
STI0555
EMISSION CONTROL INFORMATION LABEL The emission control is at- tached to the underside of the hood as shown.
information label
TIRE AND LOADING INFORMATION LABEL The cold tire pressure is shown on the Tire and Loading Information label affixed to the pillar as illustrated.
AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is at- tached to the underside of the hood as shown.
9-10 Technical and consumer information
Model "S35-D" EDITED: 2010/ 6/ 4
INSTALLING FRONT LICENSE PLATE
Black plate (341,1)
EXCEPT FOR Kro¯ m MODELS Use the following steps to mount the license plate:
Before mounting the license plate, confirm that the following parts are enclosed in the plastic bag.
License plate bracket
J-nut 6 2
. Screw 6 2
. Screw grommet 6 2
1. Temporarily place the license plate bracket by aligning the lower part *A of it with the lines *B on the bumper.
2. Mark the pilot hole points with a felt-tip pen the license plate
through the holes of bracket.
3. Remove the license plate bracket.
4. Carefully drill two pilot holes using a 0.39 in (10 mm) drill bit at the marked locations. (Be sure that the drill only goes through the fascia, or damage to the nut may occur.)
5.
Insert grommets into the hole on the fascia.
STI0599
Technical and consumer information 9-11
Model "S35-D" EDITED: 2010/ 6/ 4
Black plate (342,1)
6.
7.
8.
9.
Insert a flat-blade screwdriver into the grommet hole to add 908 turn onto the part *C . Insert a J-nut into the license plate bracket before placing the license plate bracket on the fascia.
Install the license plate bracket with screws.
Install the license plate with bolts that are no longer than 0.55 in (14 mm).
9-12 Technical and consumer information
STI0677
Model "S35-D" EDITED: 2010/ 6/ 4
FOR Kro¯ m MODELS Use the following steps to mount the license plate:
Before mounting the license plate, confirm that the following parts are enclosed in the vinyl bag.
License plate bracket
J-nut 6 2
. Screw 6 2
. Screw grommet 6 2
1. Park the vehicle on flat, level ground.
2. Temporarily place the license plate bracket while aligning points *A of the front bumper fascia with holes *B in the license plate bracket.
3. Confirm that points *A and *B are aligned. 4. Remove the license plate bracket. 5. Carefully drill two shallow pilot holes *A using a 0.39 in (10 mm) drill bit at the marked locations. (Be sure that the drill only goes through the fascia, or da- mage to the nut may occur.)
6.
7.
Insert grommets into the hole on the fascia.
Insert a flat-blade screwdriver into the grommet hole to add a 908 turn onto the part *C .
8.
9.
Insert a J-nut into the license plate bracket before placing the license plate bracket on the fascia.
the license plate bracket with the
Install screws.
10. Install the license plate with bolts that are
not longer than 0.55 in (14 mm).
Black plate (343,1)
VEHICLE LOADING INFORMATION
WARNING
It is extremely dangerous to ride in a cargo area inside the vehi- cle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
. Be sure everyone in your vehicle is in a seat and using a seat belt properly.
TERMS
It is important to familiarize yourself with the following terms before loading your vehicle: . Curb Weight
(actual weight of your vehicle) including: standard and optional equipment, fluids, emergency tools, and spare tire assembly. This weight does not in- clude passengers and cargo.
- vehicle weight
. GVW (Gross Vehicle Weight) - curb weight plus the combined weight of passengers and cargo.
Technical and consumer information 9-13
Model "S35-D" EDITED: 2010/ 6/ 4
. Cargo capacity - permissible weight of cargo, the subtracted weight of occu- pants from the load limit.
VEHICLE LOAD CAPACITY
Do not exceed the load limit of your vehicle shown as “The combined weight of occu- pants and cargo” on the Tire and Loading Information label. Do not exceed the number of occupants shown as “Seating Capacity” on the Tire and Loading Informa- tion label.
To get “the combined weight of occupants and cargo”, add the weight of all occu- pants, then add the total luggage weight. Examples are shown in the following illustration.
. GVWR (Gross Vehicle Weight Rating) - maximum total combined weight of the unloaded vehicle, passengers, luggage, hitch, trailer tongue load and any other optional equipment. This information is located on the F.M.V.S.S./C.M.V.S.S. label.
. GAWR (Gross Axle Weight Rating) - maximum weight (load) limit specified