2008 Nissan Quest Owners Manual

moved, store it in a secure place. Be sure to install the head restraint when the child restraint

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-33

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

LRS0664

LRS0671

WRS0697

Front facing rigid-mounted (cid:150) step 3

is removed. If the seating position does not have an adjustable head restraint and it is interfering with the proper child restraint fit, try another seating position or a different child restraint.

Front facing (cid:150) step 5

Front facing (cid:150) step 7

5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments. If the child restraint is equipped with a top tether strap, route the top tether strap and secure the tether strap to the tether anchor point. See (cid:147)Top tether strap child restraint(cid:148) in this section.

6.

7. Before placing the child in the child restraint, hold the child restraint near the LATCH at- tachment and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the anchor attachments to further tighten the child restraint. If you are unable to properly secure the restraint, move the re- straint to another seating position and try again, or try a different child restraint. Not all child restraints fit in all types of vehicles.

1-34 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

is loose,

8. Check to make sure the child restraint is properly secured prior to each use. If the child restraint repeat steps 4
through 7. Rear-facing Follow these steps to install a rear-facing child restraint in the 2nd row captain(cid:146)s chairs using LATCH: 1. Recline the seatback if the seatback is ad- justable to assist in attaching the child re- straint to the lower anchors.

2. Position the child restraint on the seat. Al- ways follow the child restraint manufactur- er(cid:146)s instructions.

Rear facing web-mounted (cid:150) step 3

Rear facing rigid-mounted (cid:150) step 3

LRS0665

LRS0666

3. Secure the child restraint anchor attach- ments to the LATCH lower anchors. Check to make sure the LATCH attachment is prop- erly attached to the lower anchors.

4. Return the seatback to its normal upright

and locked position.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-35

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

7. Check to make sure the child restraint is properly secured prior to each use. If the child restraint repeat steps 3
through 6.

is loose,

CHILD RESTRAINT INSTALLATION USING LATCH-3RD ROW BENCH SEAT (if so equipped)

WARNING

c Attach LATCH compatible child re- straints only at the locations shown. For the LATCH lower anchor locations, see (cid:147)Lower Anchors and Tethers for CHil- dren System (LATCH)(cid:148) in this section. If a child restraint is not secured properly, your child could be seriously injured or killed in an accident.

c The LATCH anchors are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstance are they to be used for adult seat belts or harnesses.

Front facing (cid:150) step 5

Front facing (cid:150) step 6

LRS0673

LRS0674

5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments.

6. Before placing the child in the child restraint, hold the child restraint near the LATCH at- tachment and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the anchor attachments to further tighten the child restraint. If you are unable to properly secure the restraint, move the re- straint to another seating position and try again, or try a different child restraint. Not all child restraints fit in all types of vehicles.

1-36 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

c Inspect the lower anchors by inserting your fingers into the lower anchor area and feeling to make sure there are no obstructions over the LATCH anchors, such as seat belt webbing or seat cush- ion material. The child restraint will not be secured properly if the LATCH an- chors are obstructed.

Front-facing Follow these steps to install a front-facing child restraint in the 3rd row bench seats using LATCH: 1. Recline the seatback if the seatback is ad- justable to assist in attaching the child re- straint to the lower anchors.

2. Position the child restraint on the seat. Al- ways follow the child restraint manufactur- er(cid:146)s instructions.

Front facing web-mounted (cid:150) step 3

Front facing rigid-mounted (cid:150) step 3

WRS0685

WRS0686

3. Secure the child restraint anchor attach- ments to the LATCH lower anchors. Check to make sure the LATCH attachment is prop- erly attached to the lower anchors.

4. Return the seatback to its normal upright

and locked position.

The back of the child restraint should be secured against the vehicle seatback. If the seating posi- tion does not have an adjustable head restraint and it is interfering with the proper child restraint fit, try another seating position or a different child restraint.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-37

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

6.

If the child restraint is equipped with a top tether strap, route the top tether strap and secure the tether strap to the tether anchor point. See (cid:147)Top tether strap child restraint(cid:148) in this section. Do not install child restraints that require the use of the top tether strap to seating positions that do not have a top tether anchor.

LRS0671

Front facing (cid:150) step 5

5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments

1-38 Safety(cid:151)Seats, seat belts and supplemental restraint system

LRS0672

Front facing (cid:150) step 7

7. Before placing the child in the child restraint, hold the child restraint near the LATCH at- tachment and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the anchor attachments to further tighten the child restraint. If you are unable to properly secure the restraint, move the re- straint to another seating position and try again, or try a different child restraint. Not all child restraints fit in all types of vehicles.

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

is loose,

8. Check to make sure the child restraint is properly secured prior to each use. If the child restraint repeat steps 3
through 8. Rear-facing Follow these steps to install a rear-facing child restraint in the 3rd row bench seats using LATCH: 1. Recline the seatback in vehicles with adjust- able seatbacks to assist in attaching the child restraint to the lower anchors.

2. Position the child restraint on the seat. Al- ways follow the child restraint manufactur- er(cid:146)s instructions.

Rear facing web-mounted (cid:150) step 3

Rear facing rigid-mounted (cid:150) step 3

WRS0689

WRS0690

3. Secure the child restraint anchor attach- ments to the LATCH lower anchors. Check to make sure that the LATCH attachment is properly attached to the lower anchors.

4. Return the seatback to its normal upright

and locked position.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-39

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

7. Check to make sure the child restraint is properly secured prior to each use. If the child restraint repeat steps 3
through 6.

is loose,

Front facing (cid:150) step 5

Front facing (cid:150) step 6

LRS0673

LRS0674

5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your hand to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments.

6. Before placing the child in the child restraint, hold the child restraint near the LATCH at- tachment and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the anchor attachments to further tighten the child restraint. If you are unable to properly secure the restraint, move the re- straint to another seating position and try again, or try a different child restraint. Not all child restraints fit in all types of vehicles.

1-40 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

WRS0256

CHILD RESTRAINT INSTALLATION USING THE SEAT BELTS

WARNING

c Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front passenger seat. Front air bags inflate with great force. A rear-facing child restraint could be struck by the front air bag in a crash and could seriously injure or kill your child.

c NISSAN recommends that child re- straints be installed in the rear seat. However, if you must install a forward facing child restraint in the front pas- senger seat, move the passenger seat to the rearmost position. Also, be sure the front passenger air bag status light is illuminated to indicate the passenger air bag is OFF. See (cid:147)Front passenger air bag and status light(cid:148) later in this sec- tion for details.

c The three-point seat belt in your vehicle is equipped with an Automatic Locking Retractor (ALR) which must be used when installing a child restraint.

c Failure to use the ALR mode will result in the child restraint not being properly secured. The restraint could tip over or otherwise be unsecured and cause in- jury to the child in a sudden stop or collision. Also, it can change the opera- tion of the front passenger air bag. See (cid:147)Front passenger air bag and status light(cid:148) later in this section.

c When installing a child restraint system in the rear center position, both the center seat belt connector tongue and buckle tongue must be secured. See (cid:147)Attaching the 3rd row center seat belt(cid:148) earlier in this section.

c A child restraint with a top tether strap should not be used in the front passen- ger seat except for the 2-passenger cargo van.

c Front-facing child restraints can be in- stalled in all 3rd row bench seat posi- tions. However, front-facing child re- straints that require the use of a top tether strap can be installed in the cen- ter 3rd row position only. Do not install a child restraint requiring a top tether strap in an outboard position and at- tempt to angle the tether to the 3rd row center anchor.

The instructions in this section apply to child restraint installation using the vehicle seat belts in the rear seats or the front passenger seat.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-41

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

2. Position the child restraint on the seat. Al- ways follow the child restraint manufactur- er(cid:146)s instructions

The back of the child restraint should be secured against the vehicle seatback. If necessary, adjust or remove the head restraint to obtain the correct child restraint fit. See (cid:147)Head restraint adjust- ment(cid:148) in this section. If the head restraint is removed, store it in a secure place. Be sure to install the head restraint when the child restraint is removed. If the seating position does not have an adjustable head re- straint and it is interfering with the proper child restraint fit, try another seating position or a dif- ferent child restraint.

WRS0680

Front facing (cid:150) step 3

3. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer(cid:146)s in- structions for belt routing.

WRS0699
Front-facing (front passenger seat) (cid:150) step 1
Front-facing Follow these steps to install a front-facing child restraint using the vehicle seat belt in the rear seats or in the front passenger seat: 1. If you must install a child restraint in the front seat, it should be placed in a front-facing direction only. Move the seat to the rearmost position. Child restraints for infants must be used in the rear-facing direction and therefore must not be used in the front seat.

1-42 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

Front facing (cid:150) step 4

Front facing (cid:150) step 5

Front facing (cid:150) step 6

LRS0667

LRS0668

WRS0681

4. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode). It reverts to the Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted.

5. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt.

6. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while pulling up on the seat belt.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-43

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

8. Before placing the child in the child restraint, hold the child restraint near the seat belt path and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the shoulder belt to further tighten the child restraint. If you are unable to properly secure the restraint, move the restraint to another seating position and try again, or try a differ- ent child restraint. Not all child restraints fit in all types of vehicles.

9. Check that the retractor is in the ALR mode by trying to pull more seat belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the retractor is in the ALR mode.

10. Check to make sure the child restraint is properly secured prior to each use. If the seat belt locked, repeat steps 3
through 8.

is not

WRS0698

Front facing (cid:150) step 7

7.

If the child restraint is equipped with a top tether strap, route the top tether strap and secure the tether strap to the tether anchor point. See (cid:147)Top tether strap child restraint(cid:148) in this section. Do not install child restraints that require the use of a top tether strap to seating positions that do not have a top tether anchor.

1-44 Safety(cid:151)Seats, seat belts and supplemental restraint system

11.

WRS0475

Front facing (cid:150) step 11

If the child restraint is installed in the front passenger seat, turn the ignition switch to the ON position. The front passenger air bag should illuminate. If this status light light is not illuminated see 9Front passenger air bag and status light9 in this section. Move the child restraint to another seating position. Have system checked by a NISSAN dealer.

the

After the child restraint is removed and the seat belt is fully retracted, the ALR mode (child re- straint mode) is canceled.

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

WRS0256

WRS0761

LRS0669

Rear-facing (cid:150) step 1

Rear-facing Follow these steps to install a rear-facing child restraint using the vehicle seat belt in the rear seats: 1. Child restraints for infants must be used in the rear-facing direction and therefore must not be used in the front seat. Position the child restraint on the seat. Always follow the restraint manufacturer(cid:146)s instructions.

Rear facing (cid:150) step 2

Rear facing (cid:150) step 3

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer(cid:146)s in- structions for belt routing.

3. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode). It reverts to the Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-45

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

Rear facing (cid:150) step 4

Rear facing (cid:150) step 5

Rear facing (cid:150) step 6

LRS0670

WRS0762

WRS0763

4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt.

5. Remove any additional slack from the child restraint; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seat- back while pulling up on the seat belt.

6. Before placing the child in the child restraint, hold the child restraint near the seat belt path and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the shoulder belt to further tighten the child restraint. If you are unable to properly secure the restraint, move the restraint to another rear seating position and try again, or try a different child restraint. Not all child re- straints fit in all types of vehicles.

1-46 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

BOOSTER SEATS

7. Check that the retractor is in the ALR mode by trying to pull more seat belt out of the retractor. If you cannot pull any more seat belt webbing out of the retractor, the retrac- tor is in the ALR mode.

8. Check to make sure that the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 7.

After the child restraint is removed and the seat belt fully retracted, the ALR mode (child restraint mode) is canceled.

ARS1098

PRECAUTIONS ON BOOSTER SEATS

WARNING

c Infants and small children should al- ways be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint or booster seat can result in serious injury or death.

c Infants and small children should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe accident. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself.

c NISSAN recommends that the booster seat be installed in the rear seat. Ac- cording to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. If you must install a booster seat in the front seat, see (cid:147)Booster seat installa- tion(cid:148) in this section.

seating

position

c A booster seat must only be installed in lap/shoulder belt. Failure to use a three-point type seat belt with a booster seat can result in a serious in- jury in sudden stop or collision.

that

has

c Improper use or improper installation of a booster seat can increase the risk or severity of injury for both the child and other occupants of the vehicle and can lead to serious injury or death in an accident.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-47

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

c Do not use towels, books, pillows or other items in place of a booster seat. Items such as these may move during normal driving or a collision and result in serious injury or death. Booster seats are designed to be used with a lap/shoulder belt. Booster seats are de- signed to properly route the lap and shoulder portions of the seat belt over the strongest portions of a child(cid:146)s body to provide the maximum protection dur- ing a collision.

c Follow all of the booster seat manufac- turer(cid:146)s instructions for installation and use. When purchasing a booster seat, be sure to select one which will fit your child and vehicle. It may not be possible to properly install some types of booster seats in your vehicle.

c If the booster seat and seat belt is not used properly, the risk of a child being injured in a collision or a sudden stop greatly increases.

c Adjustable seatbacks should be posi- tioned to fit the booster seat, but as upright as possible.

c After placing the child in the booster seat and fastening the seat belt, make sure the shoulder portion of the belt is away from the child(cid:146)s face and neck and the lap portion of the belt does not cross the abdomen.

c Do not put the shoulder belt behind the child or under the child(cid:146)s arm. If you must install a booster seat in the front seat, see (cid:147)Booster seat installation(cid:148) later in this section.

c When your booster seat is not in use, keep it secured with a seat belt to pre- vent it from being thrown around in case of a sudden stop or accident.

CAUTION

Remember that a booster seat left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the booster seat.

1-48 Safety(cid:151)Seats, seat belts and supplemental restraint system

LRS0455
Booster seats of various sizes are offered by several manufacturers. When selecting any booster seat, keep the following points in mind: c Choose only a booster seat with a label certifying that it complies with Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213.

c Check the booster seat in your vehicle to be sure it is compatible with the vehicle(cid:146)s seat and seat belt system.

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

BOOSTER SEAT INSTALLATION

WARNING

NISSAN recommends that booster seats be installed in the rear seat. However, if you must install a booster seat in the front passenger seat, move the passenger(cid:146)s seat to the rearmost position.

CAUTION

Do not use the lap/shoulder belt Auto- matic Locking Retractor mode when using a booster seat with the seat belts.

Follow these steps to install a booster seat in the rear seat or in the front passenger seat:

LRS0512
All U.S. states and Canadian provinces or territories require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being operated. The instructions in this section apply to booster seat installation in the rear seats or the front passenger seat.

LRS0453
c Make sure the child(cid:146)s head will be properly supported by the booster seat or vehicle seat. The seat back must be at or above the center of the child(cid:146)s ears. For example, if a low back booster seat s1 is chosen, the vehicle seat back must be at or above the center of the child(cid:146)s ears. If the seat back is lower than the center of the child(cid:146)s ears, a high back booster seat s2 should be used. c If the booster seat is compatible with your vehicle, place your child in the booster seat and check the various adjustments to be sure the booster seat is compatible with your child. Always follow all recommended pro- cedures.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-49

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

WRS0699
1. If you must install a booster seat in the front seat, move the seat to the rear- most position.

2. Position the booster seat on the seat. Only place it in a front facing direction. Always follow the booster seat manufacturer(cid:146)s in- structions.

Rear center position

Rear outboard position

LRS0513

LRS0512

3. The booster seat should be positioned on the vehicle seat so that it is stable. If neces- sary, adjust or remove the head restraint to obtain the correct booster seat fit. See (cid:147)Head restraint adjustment(cid:148) earlier in this section. If the head restraint is removed, store it in a secure place. Be sure to install the head restraint when the booster seat is removed. If the seating position does not have an adjustable head restraint and it is interfering with the proper booster seat fit, try another seating position or a different booster seat.

1-50 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

4. Position the lap portion of the seat belt low and snug on the child(cid:146)s hips. Be sure to follow the booster seat manufacturer(cid:146)s in- structions for adjusting the belt routing.

5. Pull the shoulder belt portion of the seat belt toward the retractor to take up extra slack. Be sure the shoulder belt is positioned across the top, middle portion of the child(cid:146)s shoulder. Be sure to follow the booster seat manufacturer(cid:146)s instructions for adjusting the belt routing.

LRS0454

Front passenger position

6. Follow the warnings, cautions and instruc- tions for properly fastening a seat belt shown in the (cid:147)Three-point seat belt with retractor(cid:148) earlier in this section.

7.

WRS0475
If the booster seat is installed in the front passenger seat, turn the ignition switch to the ON position. The front passenger air bag status light may or may not illuminate, depending on the size of the child and the type of booster seat being used. See (cid:147)Front passenger air bag and status light(cid:148) later in this section.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-51

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

SUPPLEMENTAL RESTRAINT SYSTEM

PRECAUTIONS ON SUPPLEMENTAL RESTRAINT SYSTEM This Supplemental Restraint System (SRS) sec- tion contains important information concerning the following systems: c Driver and passenger supplemental front- impact air bag (NISSAN Advanced Air Bag System)

c Front seat-mounted side-impact supple-

mental air bag

c Roof-mounted curtain side-impact supple-

mental air bag

c Seat belt with pretensioner Supplemental front-impact air bag system: The NISSAN Advanced Air Bag System can help cushion the impact force to the head and chest of the driver and front passenger in certain frontal collisions. Front seat-mounted side-impact supple- mental air bag system: This system can help cushion the impact force to the chest area of the driver and front passenger in certain side impact collisions. The side air bags are designed to inflate on the side where the vehicle is impacted.

Roof-mounted curtain side-impact supple- mental air bag system: This system can help cushion the impact force to the head of occu- pants in front and rear outboard seating positions in certain side impact collisions. The curtain air bags are designed to inflate on the side where the vehicle is impacted. These supplemental restraint systems are de- signed to supplement the crash protection pro- vided by the seat belts and are not a substitute for them. Seat belts should always be correctly worn and the occupant seated a suitable dis- tance away from the steering wheel, instrument panel and door finishers. See (cid:147)Seat belts(cid:148) earlier in this section for instructions and precautions on seat belt usage. The supplemental air bags operate only when the ignition switch is in the ON or START position. After turning the ignition key to the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7
seconds if the system is operational.

1-52 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

c The driver and front passenger seat belt buckles are equipped with sensors that detect if the seat belts are fastened. The Advanced Air Bag System monitors the severity of a collision and seat belt us- age then inflates the air bags. Failure to properly wear seat belts can increase the risk or severity of injury in an accident.

c The front passenger seat is equipped with an occupant classification sensor (pressure sensor) that turns the front passenger air bag OFF under some conditions. This sensor is only used in this seat. Failure to be properly seated and wearing the seat belt can increase the risk or severity of injury in an acci- dent. See (cid:147)Front passenger air bag and status light(cid:148) later in this section.

c Keep hands on the outside of the steer- ing wheel. Placing them inside the steering wheel rim could increase the risk that they are injured when the front air bag inflates.

WARNING

c The front air bags ordinarily will not inflate in the event of a side impact, rear impact, rollover, or lower severity fron- tal collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents. c The front passenger air bag will not inflate if the passenger air bag status light is lit or if the front passenger seat is unoccupied. See (cid:147)Front passenger air bag and status light(cid:148) later in this section.

WRS0031

c The seat belts and the front air bags are most effective when you are sitting well back and upright in the seat. The front air bags inflate with great force. Even with the NISSAN Advanced Air Bag Sys- tem, if you are unrestrained, leaning forward, sitting sideways or out of posi- tion in any way, you are at greater risk of injury or death in a crash. You may also receive serious or fatal injuries from the front air bag if you are up against it when it inflates. Always sit back against the seatback and as far away as practi- cal from the steering wheel or instru- ment panel. Always use the seat belts.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-53

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

ARS1133

ARS1041

WARNING

c Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations.

1-54 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

ARS1042

ARS1043

ARS1044

WARNING

c Children may be severely injured or killed when the front air bags, side air bags or curtain air bags inflate if they are not properly restrained. Pre-teens and children should be properly re- strained in the rear seat, if possible.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-55

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

ARS1045

WRS0256

WRS0431

WARNING

c Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An in- flating front air bag could seriously in- jure or kill your child. See (cid:147)Child re- straints(cid:148) earlier in this section for details.

Do not lean against the door.

WARNING

Front seat-mounted side-impact supple- mental air bags and roof-mounted curtain side-impact supplemental air bags: c The side air bags and curtain air bags ordinarily will not inflate in the event of a frontal impact, rear impact, rollover or lower severity side collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents.

1-56 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

WARNING

c The seat belts, the side air bags and curtain air bags are most effective when you are sitting well back and upright in the seat with both feet on the floor. The side air bag and curtain air bag inflate with great force. Do not allow anyone to place their hand, leg or face near the side air bag on the side of the seatback of the front seat or near the side roof rails. Do not allow anyone sitting in the front seats or rear outboard seats to extend their hand out of the window or lean against the door. Some examples of dangerous riding positions are shown in the previous illustrations.

SSS0162

WRS0306

WARNING

c When sitting in the 2nd row rear seat, do not hold onto the seatback of the front seat. If the side air bag inflates, you may be seriously injured. Be especially care- ful with children, who should always be properly restrained. Some examples of dangerous riding positions are shown in the illustrations.

c Do not use seat covers on the front seatbacks. They may interfere with side air bag inflation.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-57

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

SSS0159

1.

2.

3.

Roof-mounted curtain side-impact supplemental air bag inflators Roof-mounted curtain side-impact supplemental air bag (driver(cid:146)s side) Seat belt buckle switches

LRS0679

4.

Supplemental front-impact air bag modules

5. Crash zone sensor 6. 7. Occupant classification system control

Air bag Control Unit (ACU)

unit

1-58 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—cathy X

8. Occupant classification sensor

(pressure sensor) Seat belt with pretensioner

9. 10. Satellite sensors 11. Front seat-mounted side-impact

supplemental air bag modules

12. Roof-mounted curtain side-impact

supplemental air bag (passenger(cid:146)s side)

NISSAN Advanced Air Bag System (front seats) This vehicle is equipped with the NISSAN Ad- vanced Air Bag System for the driver and front passenger seats. This system is designed to meet certification requirements under U.S. regu- lations. It is also permitted in Canada. However, all of the information, cautions and warn- ings in this manual still apply and must be followed.

The driver supplemental front-impact air bag is located in the center of the steering wheel. The passenger supplemental front-impact air bag is mounted in the dashboard above the glove box. The front air bags are designed to inflate in higher severity frontal collisions, although they may in- flate if the forces in another type of collision are similar to those of a higher severity frontal impact. They may not inflate in certain frontal collisions.

Vehicle damage (or lack of it) is not always an indication of proper front air bag system opera- tion.

dealer. If you are considering modification of your vehicle due to a disability, you may also contact NISSAN. Contact information is contained in the front of this Owner(cid:146)s Manual.

The NISSAN Advanced Air Bag System has dual stage inflators. It also monitors information from the crash zone sensor, the Air bag Control Unit (ACU), seat belt buckle sensors, occupant clas- sification sensor (pressure sensor) and passen- ger seat belt tension sensor. Inflator operation is based on the severity of a collision and seat belt usage for the driver. For the front passenger, it additionally monitors the weight of an occupant or object on the seat and seat belt tension. Based on information from the sensors, only one front air bag may inflate in a crash, depending on the crash severity and whether the front occupants are belted or unbelted. Additionally, the front passenger air bag may be automatically turned OFF under some conditions, depending on the weight detected on the passenger seat and how the seat belt is used. If the front passenger air bag is OFF, the passenger air bag status light will be illuminated (if the seat is unoccupied, the light will not be illuminated, but the air bag will be off). See (cid:147)Front passenger air bag and status light(cid:148) later in this section for further details. One front air bag inflating does not indicate improper performance of the system. If you have any questions about your air bag system, please contact NISSAN or your NISSAN

When a front air bag inflates, a fairly loud noise may be heard, followed by the release of smoke. This smoke is not harmful and does not indicate a fire. Care should be taken to not inhale it, as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly. Front air bags, along with the use of seat belts, help to cushion the impact force on the face and chest of the front occupants. They can help save lives and reduce serious injuries. However, an inflating front air bag may cause facial abrasions or other injuries. Front air bags do not provide restraint to the lower body. Even with the NISSAN Advanced Air Bag Sys- tem, seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the steering wheel or instru- ment panel. The front air bags inflate quickly in order to help protect the front occupants. Be- cause of this, the force of the front air bag inflating can increase the risk of injury if the occupant is too close to, or is against, the front air bag module during inflation. The front air bags deflate quickly after a collision. Safety(cid:151)Seats, seat belts and supplemental restraint system 1-59

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—cathy X

The front air bags operate only when the ignition switch is in the ON or START posi- tion. After turning the ignition key to the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7
seconds if the system is operational.

Status light

is The front passenger air bag status light located near the climate controls in the center of the instrument panel. The light operates as fol- lows: c Unoccupied passenger(cid:146)s seat: The

is OFF and the front passenger air bag is OFF and will not inflate in a crash.

c Passenger(cid:146)s seat occupied by a small adult, child or child restraint as outlined in this illuminates to indicate section: The that the front passenger air bag is OFF and will not inflate in a crash.

c Occupied passenger seat and the passen- ger meets the conditions outlined in this section: The light is OFF to indicate that the front passenger air bag is opera- tional.

Front passenger air bag

The front passenger air bag is designed to auto- matically turn OFF when the vehicle is operated under some conditions as described below in accordance with U.S. regulations. If the front passenger air bag is OFF, it will not inflate in a crash. The driver air bag and other air bags in your vehicle are not part of this system.

Front passenger air bag and status light

WRS0475

WARNING

The front passenger air bag is designed to automatically turn OFF under some con- ditions. Read this section carefully to learn how it operates. Proper use of the seat, seat belt and child restraints is nec- essary for most effective protection. Fail- ure to follow all instructions in this manual concerning the use of seats, seat belts and child restraints can increase the risk or severity of injury in an accident.

1-60 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

The purpose of the regulation is to help reduce the risk of injury or death from an inflating air bag to certain front passenger seat occupants, such as children, by requiring the air bag to be auto- matically turned OFF. Certain sensors are used to meet the requirements.

One sensor used is the occupant classification sensor (pressure sensor). It is in the bottom of the front passenger seat cushion and is designed to detect an occupant and objects on the seat by weight. It works together with seat belt sensors described later. For example, if a child is in the front passenger seat, the Advanced Air Bag Sys- tem is designed to turn the passenger air bag OFF in accordance with the regulations. Also, if a child restraint of the type specified in the regula- tions is on the seat, its weight and the child(cid:146)s weight can be detected and cause the air bag to turn OFF. Occupant classification sensor opera- tion can vary depending on the front passenger seat belt sensors. The front passenger seat belt sensors are de- signed to detect if the seat belt is buckled and the amount of tension on the seat belt, such as when it is in the Automatic Locking Retractor (ALR) mode (child restraint mode). Based on the weight on the seat detected by the occupant classification sensor and the belt tension de- tected on the seat belt, the Advanced Air Bag System determines whether the front passenger

air bag should be automatically turned OFF as required by the regulations.

crash instead of being OFF. See (cid:147)Child re- straints(cid:148) earlier in this section for proper use and installation.

In addition,

Front passenger seat adult occupants who are properly seated and using the seat belt as out- lined in this manual should not cause the passen- ger air bag to be automatically turned OFF. For small adults it may be turned OFF, however if the occupant takes his/her weight off the seat cush- ion (for example, by not sitting upright, by sitting on an edge of the seat, or by otherwise being out of position), this could cause the sensor to turn the air bag OFF. if the occupant improperly uses the seat belt in the ALR mode, this could cause the air bag to be turned OFF. Always be sure to be seated and wearing the seat belt properly for the most effective protection by the seat belt and supplemental air bag. NISSAN recommends that pre-teens and chil- dren be properly restrained in a rear seat. NISSAN also recommends that appropriate child restraints and booster seats be properly installed in a rear seat. If this is not possible, the occupant classification sensor and seat belt sensors are designed to operate as described above to turn the front passenger air bag OFF for specified child restraints as required by the regulations. Failing to properly secure child restraints and to use the ALR mode may allow the restraint to tip or move in an accident or sudden stop. This can also result in the passenger air bag inflating in a

If the front passenger seat is not occupied the passenger air bag is designed not to inflate in a crash. However, heavy objects placed on the seat could result in air bag inflation, because of the object(cid:146)s weight detected by the occupant classification sensor. Other conditions could also result in air bag inflation, such as if a child is standing on the seat, or if two children are on the seat, contrary to the instructions in this manual. Always be sure that you and all vehicle occupants are seated and restrained properly. Using the passenger air bag status light, you can monitor when the front passenger air bag is au- tomatically turned OFF with the seat occupied. The light will not illuminate when the front pas- senger seat is unoccupied. If an adult occupant is in the seat but the passen- ger air bag status light is illuminated (indicating that the air bag is OFF), it could be that the person is a small adult, or is not sitting on the seat properly or not using the seat belt properly. If a child restraint must be used in the front seat, the passenger air bag status light may or may not be illuminated, depending on the size of the child and the type of child restraint being used. If the air bag status light is not illuminated (indicating that Safety(cid:151)Seats, seat belts and supplemental restraint system 1-61

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

the air bag might inflate in a crash), it could be that the child restraint or seat belt is not being used properly. Make sure that the child restraint is installed properly, the seat belt is used properly and the occupant is positioned properly. If the air bag status light is not illuminated, reposition the occupant or child restraint in a rear seat.

If the passenger air bag status light will not illu- minate even though you believe that the child restraint, the seat belts and the occupant are properly positioned, the system may be sensing an unoccupied seat (in which case the air bag is OFF). Your NISSAN dealer can check that the system is OFF by using a special tool. However, until you have confirmed with your dealer that your air bag is working properly, reposition the occupant or child restraint in a rear seat.

The air bag system and passenger air bag status light will take a few seconds to register a change in the passenger seat status. For example, if a large adult who is sitting in the front passenger seat exits the vehicle, the passenger air bag status light will go from OFF to ON for a few seconds and then to OFF. This is normal system operation and does not indicate a malfunction.

If a malfunction occurs in the front passenger air bag system, the supplemental air bag warning light , located in the meter and gauges area

in the center of the instrument panel, will blink. Have the system checked by a NISSAN dealer. Other supplemental front-impact air bag precautions

WARNING

c Do not place any objects on the steer- ing wheel pad or on the instrument panel. Also, do not place any objects between any occupant and the steering wheel or instrument panel. Such ob- jects may become dangerous projec- tiles and cause injury if the front air bag inflates.

c Immediately after

inflation, several front air bag system components will be hot. Do not touch them; you may se- verely burn yourself.

c No unauthorized changes should be made to any components or wiring of the supplemental air bag system. This is to prevent accidental inflation of the supplemental air bag or damage to the supplemental air bag system.

c Do not make unauthorized changes to your vehicle(cid:146)s electrical system, sus- pension system or front end structure. This could affect proper operation of the front air bag system.

c Tampering with the front air bag system may result in serious personal injury. Tampering includes changes to the steering wheel and the instrument panel assembly by placing material over the steering wheel pad and above the instrument panel or by installing additional trim material around the air bag system.

c Modifying or tampering with the front passenger seat may result in serious personal injury. For example, do not change the front seats by placing mate- rial on the seat cushion or by installing additional trim material, such as seat covers, on the seat that are not specifi- cally designed to assure proper air bag operation. Additionally, do not stow any objects under the front passenger seat or the seat cushion and seatback. Such objects may interfere with the proper operation of the occupant classifica- tion sensor (pressure sensor).

1-62 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

c No unauthorized changes should be made to any components or wiring of the seat belt system. This may affect the front air bag system. Tampering with the seat belt system may result in seri- ous personal injury.

c Work on and around the front air bag system should be done by a NISSAN dealer. Installation of electrical equip- ment should also be done by a NISSAN dealer. The Supplemental Restraint System (SRS) wiring should not be modified or disconnected. Unautho- rized electrical test equipment and probing devices should not be used on the air bag system.

c A cracked windshield should be re- placed immediately by a qualified re- pair facility. A cracked windshield could affect the function of the supplemental air bag system.

c The SRS wiring harness connectors are easy

orange

for

yellow and identification.

When selling your vehicle, we request that you inform the buyer about the front air bag system and guide the buyer to the appropriate sections in this Owner(cid:146)s Manual.

inflate if the forces in another type of collision are similar to those of a higher severity side impact. They are designed to inflate on the side where the vehicle is impacted. They may not inflate in cer- tain side collisions.

WRS0532

Vehicle damage (or lack of it) is not always an indication of proper side air bag and curtain air bag operation. When the side air bags and curtain air bags inflate, a fairly loud noise may be heard, followed by release of smoke. This smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of a breathing con- dition should get fresh air promptly. Side air bags, along with the use of seat belts, help to cushion the impact force on the chest of the front occupants. Curtain air bags help to cushion the impact force to the head of occu- pants in the front and rear outboard seating po- sitions. They can help save lives and reduce serious injuries. However, an inflating side air bag and curtain air bag may cause abrasions or other injuries. Side air bags and curtain air bags do not provide restraint to the lower body. The seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the side air bag. Rear seat passengers should be seated as far away as Safety(cid:151)Seats, seat belts and supplemental restraint system 1-63

Front seat-mounted side-impact supplemental air bag and roof- mounted curtain side-impact supplemental air bag systems The side air bags are located in the outside of the seatback of the front seats. The curtain air bags are located in the side roof rails. These systems are designed to meet voluntary guidelines to help reduce the risk of injury to out-of-position occu- pants. However, all of the information, cau- tions and warnings in this manual still ap- ply and must be followed. The side air bags and curtain air bags are designed to inflate in higher severity side collisions, although they may

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

practical from the door finishers and side roof rails. The side air bags and curtain air bags inflate quickly in order to help protect the front and rear outboard occupants. Because of this, the force of the side air bag and curtain air bag inflating can increase the risk of injury if the occupant is too close to, or is against, these air bag modules during inflation. The side air bag and curtain air bag will deflate quickly after the collision is over. The side air bags and curtain air bags op- erate only when the ignition switch is in the ON or START position.

After turning the ignition key to the ON position, the supplemental air bag warning light illuminates. The supplemental air bag warning light will turn off after about 7
seconds if the system is operational.

WARNING

c Do not place any objects near the seat- back of the front seats. Also, do not place any objects (an umbrella, bag, etc.) between the front door finisher and the front seat. Such objects may become dangerous projectiles and cause injury if a side air bag inflates.

c Right after inflation, several side air bag and curtain air bag system components will be hot. Do not touch them; you may severely burn yourself.

c No unauthorized changes should be made to any components or wiring of the side air bag and curtain air bag systems. This is to prevent damage to or accidental inflation of the side air bag and curtain air bag systems.

c Do not make unauthorized changes to your vehicle(cid:146)s electrical system, sus- pension system or side panel. This could affect proper operation of the side air bag and curtain air bag systems. c Tampering with the side air bags may result in serious personal injury. For example, do not change the front seats by placing material near the seatbacks or by installing additional trim material, such as seat covers, around the side air bag.

c Work around and on the side air bag and curtain air bag systems should be done by a NISSAN dealer. Installation of electrical equipment should also be done by a NISSAN dealer. The SRS wir- ing harnesses* should not be modified or disconnected. Unauthorized electri- cal test equipment and probing devices should not be used on the side air bag system.

* The SRS wiring harness connectors are yellow and orange for easy identification.

When selling your vehicle, we request that you inform the buyer about the side air bag and curtain air bag systems and guide the buyer to the appropriate sections in this Owner(cid:146)s Manual. Seat belts with pretensioners (Front seats)

WARNING

c The pretensioners cannot be reused af- ter activation. They must be replaced together with the retractor and buckle as a unit.

1-64 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

c If the vehicle becomes involved in a frontal collision but a pretensioner is not activated, be sure to have the pre- tensioner system checked and, if nec- essary, your NISSAN dealer.

replaced by

c No unauthorized changes should be made to any components or wiring of the pretensioner system. This is to pre- vent damage to or accidental activation of the pretensioners. Tampering with the pretensioner system may result in serious personal injury.

c Work around and on the pretensioner system should be done by a NISSAN dealer. Installation of electrical equip- ment should also be done by a NISSAN dealer. Unauthorized electrical test equipment and probing devices should not be used on the pretensioner system. c If you need to dispose of a pretensioner or scrap the vehicle, contact a NISSAN dealer. Correct pretensioner disposal procedures are set forth in the appropri- ate NISSAN Service Manual. Incorrect disposal procedures could cause per- sonal injury.

system may not function properly. They must be checked and repaired. Take your vehicle to the nearest NISSAN dealer. When selling your vehicle, we request that you inform the buyer about the pretensioner system and guide the buyer to the appropriate sections in this Owner(cid:146)s Manual.

The pretensioner system activates in conjunction with the front air bag system. The pretensioner system also activates with curtain and rollover air bags in certain types of rollover collisions or near rollovers. Working with the seat belt retractor, it helps tighten the seat belt when the vehicle be- comes involved in certain types of collisions, helping to restrain front seat occupants.

The pretensioner is encased with the seat belt retractor. These seat belts are used the same way as conventional seat belts.

When a pretensioner activates, smoke is re- leased and a loud noise may be heard. This smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly.

After pretensioner activation, load limiters allow the seat belt to release webbing (if necessary) to reduce forces against the chest.

the

supplemental

If any abnormality occurs in the pretensioner sys- tem, air bag warning light will not come on, will flash intermit- tently or will turn on for 7 seconds and remain on after the ignition key has been turned to the ON or START position. In this case, the pretensioner

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-65

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational.

If any of the following conditions occur, the front air bag, side air bag, curtain air bag and preten- sioner systems need servicing: c The supplemental air bag warning light re-

mains on after approximately 7 seconds.

c The supplemental air bag warning light

flashes intermittently.

c The supplemental air bag warning light does

not come on at all.

Under these conditions, the front air bags, side air bags, curtain air bags or pretensioners may not operate properly. They must be checked and repaired. Take your vehicle to the nearest NISSAN dealer.

WARNING

If the supplemental air bag warning light is on, it could mean that the front air bag, side air bags, curtain air bag and/or pre- tensioner systems will not operate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible.

LRS0318

LRS0100

1. 2.

SRS Front Air Bag Warning Labels SRS Front Seat-Mounted Side-Impact Supplemental Air Bag Warning Label

SUPPLEMENTAL AIR BAG WARNING LABELS Warning labels about the supplemental front- impact air bag, front seat-mounted side-impact supplemental air bag, and roof-mounted curtain side-impact supplemental air bag systems are placed in the vehicle as shown in the illustration.

SUPPLEMENTAL AIR BAG WARNING LIGHT air bag warning light, The supplemental displaying in the instrument panel, moni- tors the circuits of the supplemental front-impact air bag, front seat-mounted side-impact supple- mental air bag, roof-mounted curtain side-impact supplemental air bag and seat belt pretensioner systems. The monitored circuits include the Air bag Control Unit (ACU), crash zone sensor, sat- ellite sensors, side air bag modules, curtain air bag modules, pretensioners and all related wir- ing.

1-66 Safety(cid:151)Seats, seat belts and supplemental restraint system

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

c The front air bag, side air bag, curtain air bag systems, and the pretensioner system should be inspected by a NISSAN dealer if there is any damage to the front end or side portion of the vehicle.

c If you need to dispose of a supplemen- tal air bag or pretensioner or scrap the vehicle, contact a NISSAN dealer. Cor- rect supplemental air bag and preten- sioner disposal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury.

Repair and replacement procedure The front air bags, side air bags, curtain air bags and pretensioners are designed to inflate on a one-time-only basis. As a reminder, unless it is damaged, the supplemental air bag warning light remains illuminated after inflation has occurred. Repair and replacement of these supplemental air bag systems should be done only by a NISSAN dealer.

When maintenance work is required on the ve- hicle, the front air bags, side air bags, curtain air bags, pretensioners and related parts should be pointed out to the person performing the mainte- nance. The ignition switch should always be in the LOCK position when working under the hood or inside the vehicle.

WARNING

c Once a front air bag, side air bag, or curtain air bag has inflated, the air bag module will not function again and must be replaced. Additionally, if any of the front air bags inflate, the activated pretensioners must also be replaced. The air bag module and pretensioners should be replaced by a NISSAN dealer. The air bag module and pretensioners cannot be repaired.

Safety(cid:151)Seats, seat belts and supplemental restraint system 1-67

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

2 Instruments and controls

Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Meters and gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Speedometer and odometer . . . . . . . . . . . . . . . . . . . . . 2-4
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Engine coolant temperature gauge . . . . . . . . . . . . . . . 2-5
Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Warning/indicator lights and audible reminders . . . . . . . 2-7
Checking bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Indicator lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Audible reminders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Security systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Vehicle security system. . . . . . . . . . . . . . . . . . . . . . . . . 2-14
NISSAN vehicle immobilizer system . . . . . . . . . . . . . 2-15
Windshield wiper and washer switch . . . . . . . . . . . . . . . 2-16
Switch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Rear window wiper and washer switch. . . . . . . . . . . . . . 2-17
Rear window and outside mirror (if so equipped) defroster switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
Headlight and turn signal switch. . . . . . . . . . . . . . . . . . . . 2-18
Headlight control switch. . . . . . . . . . . . . . . . . . . . . . . . 2-18
Daytime running light system (Canada only) . . . . . . 2-20
Instrument brightness control . . . . . . . . . . . . . . . . . . . 2-21

Turn signal switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
Fog light switch (if so equipped) . . . . . . . . . . . . . . . . 2-22
Cornering light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
Hazard warning flasher switch . . . . . . . . . . . . . . . . . . . . . 2-23
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-24
Heated seat (if so equipped). . . . . . . . . . . . . . . . . . . . . . . 2-24
Traction Control System (TCS) off switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
Vehicle Dynamic Control (VDC) off switch (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
Rear sonar system off switch (if so equipped). . . . . . . . 2-25
Power outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-27
Sunglasses holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Instrument panel storage . . . . . . . . . . . . . . . . . . . . . . . 2-27
Console box (if so equipped) . . . . . . . . . . . . . . . . . . . 2-28
Center tray table (if so equipped). . . . . . . . . . . . . . . . 2-29
Glove box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
Map pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30
Seatback pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
Grocery hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
Cargo net (if so equipped). . . . . . . . . . . . . . . . . . . . . . 2-31
Overhead console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

Cup holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
Cargo organizer (if so equipped) . . . . . . . . . . . . . . . . 2-34
3rd row armrest bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
Cargo area storage bin. . . . . . . . . . . . . . . . . . . . . . . . . 2-35
Garment hook. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
Roof rack (if so equipped) . . . . . . . . . . . . . . . . . . . . . . 2-36
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-36
Power windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
Power vent windows (if so equipped) . . . . . . . . . . . . 2-38
Manual vent windows (if so equipped) . . . . . . . . . . . 2-39
SkyView(cid:153) glass-paneled roof (if so equipped) . . . . . . . 2-39
Moonroof (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . 2-40
Automatic moonroof . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-40
Lights on demand switch . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41

Personal lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42
Map lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-43
Console light. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44
HomeLinkT universal transceiver (if so equipped). . . . . 2-44
Programming HomeLinkT. . . . . . . . . . . . . . . . . . . . . . . 2-45
Programming HomeLinkT for Canadian customers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46
Operating the HomeLinkT universal transceiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46
Programming trouble-diagnosis . . . . . . . . . . . . . . . . . 2-46
Clearing the programmed information . . . . . . . . . . . . 2-47
Reprogramming a single HomeLinkT button . . . . . . 2-47
If your vehicle is stolen . . . . . . . . . . . . . . . . . . . . . . . . . 2-47

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

INSTRUMENT PANEL

1. 2.

3.

4.

Ventilators (P. 4-30) Headlight/fog light (if so equipped)/turn signal switch (P. 2-18) Steering wheel switch for audio control/BluetoothT hands-free phone system (if so equipped) (P. 4-62) Driver supplemental air bag/horn (P. 1-52, P. 2-24)

5. Meters and gauges (P. 2-3) 6.

Cruise control main/set switches (P. 5-13)

7. Windshield wiper/washer switch and

rear window wiper/washer switch (P. 2-16, 2-17) Display screen/Navigation system* (P. 4-2, P. 4-7, P. 4-17) Front passenger supplemental air bag (P. 1-52)

8.

9.

10. Glove box (P. 2-30) 11. Front passenger air bag status light

(P. 1-60)

12. Hazard warning flasher switch (P. 2-23) 13. Climate controls (P. 4-31, 4-40) 14. Audio system controls (P. 4-43) 15. Display screen/Navigation system*

controls (P. 4-2, P. 4-7, P. 4-17)

2-2 Instruments and controls

LIC0928

16. Power outlets (P. 2-26)

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

METERS AND GAUGES

Ignition switch (P. 5-6)

17. Shift selector lever (P. 5-8) 18. 19. Tilt steering wheel control (P. 3-21) 20. Rear sonar system off switch

(if so equipped) (P. 2-25)

21. Vehicle Dynamic Control (VDC) off switch (if so equipped) or Traction Control System (TCS) off switch (if so equipped) (P. 2-25, P. 2-25) 22. Lights on demand switch (P. 2-41) *: Refer to the separate Navigation System Own- er(cid:146)s Manual (if so equipped). See the page number indicated in paren- theses for operating details.

Tachometer

1. 2. Warning/indicator lights 3. 4. 5. 6. Odometer/Twin trip odometer

Speedometer Engine coolant temperature gauge Fuel gauge

LIC0929

Instruments and controls 2-3

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

The twin trip odometer records the distance of individual trips.

LIC0930

Speedometer

1. 2. Odometer 3. Change button SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed. Odometer/Twin trip odometer The odometer/twin trip odometer is displayed when the ignition switch is in the ON position.

The odometer records the total distance the ve- hicle has been driven.

2-4 Instruments and controls

LIC0953

! Trip

Changing the display: Pushing the change button changes the display as follows: ! Trip Trip Resetting the trip odometer: Pushing the change button for more than 1 sec- ond resets the trip odometer to zero. Elapsed time, driving distance and average speed information is also available. Refer to (cid:147)Control panel buttons(cid:148) in the (cid:147)Display screen, heater, air conditioner, audio and phone systems(cid:148) section later in this manual.

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

CAUTION

If the gauge indicates coolant tempera- ture near the hot (H) end of the normal range, reduce vehicle speed to decrease temperature. If the gauge is over the nor- mal range, stop the vehicle as soon as safely possible. If the engine is over- heated, continued operation of the ve- hicle may seriously damage the engine. See (cid:147)If your vehicle overheats(cid:148) in the (cid:147)In case of emergency(cid:148) section for immediate action required.

LIC0931

TACHOMETER The tachometer indicates engine speed in revo- lutions per minute (rpm). Do not rev the engine into the red zone s1 .

CAUTION

When engine speed approaches the red zone, shift to a higher gear or reduce en- gine speed. Operating the engine in the red zone may cause serious engine damage.

LIC0932
ENGINE COOLANT TEMPERATURE GAUGE The gauge indicates the engine coolant tempera- ture. The engine coolant temperature is within the normal range s1 when the gauge needle points within the zone shown in the illustration.

The engine coolant temperature varies with the outside air temperature and driving conditions.

Instruments and controls 2-5

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

The located on the driver(cid:146)s side of the vehicle.

indicates that the fuel-filler door is

CAUTION

c If

the vehicle runs out of

fuel, Malfunction Indicator Light the (MIL) may come on. Refuel as soon as possible. After a few driving trips, the light should turn off. If the light remains on after a few driving trips, have the vehicle inspected by a NISSAN dealer.

c For additional information, see (cid:147)Mal- function Indicator Light (MIL)(cid:148) later in this section.

LIC0933

FUEL GAUGE The gauge indicates the approximate fuel level in the tank.

The gauge may move slightly during braking, turning, acceleration, or going up or down hills.

The gauge needle returns to E (Empty) after the ignition key is turned to OFF.

The low fuel warning light comes on when the amount of fuel in the tank is getting low. Refill the fuel tank before the gauge regis- ters E (Empty).

2-6 Instruments and controls

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS

or

or

Anti-lock Braking System (ABS) warning light

Seat belt warning light and chime

Front passenger air bag status light

Brake warning light

Supplemental air bag warning light

Security indicator light

Charge warning light

Automatic transmission position indicator light

Slip indicator light

Door open warning light

Cruise main switch indicator light

Traction control system off indicator light (if so equipped)

Engine oil pressure warning light

Cruise set switch indicator light

Turn signal/hazard indicator lights

Low fuel warning light

High beam indicator light (Blue)

Vehicle dynamic control off indicator light (if so equipped)

Low tire pressure warning light

Malfunction indicator light (MIL)

Low windshield washer fluid warning light

Overdrive off indicator light

CHECKING BULBS With all doors closed, apply the parking brake and turn the ignition key to the ON position without starting the engine. The following lights will come on:

or

The following lights come on briefly and then go off:

or

If any light fails to come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the system repaired promptly.

Instruments and controls 2-7

Z REVIEW COPY—2008 Quest (van) Owners Manual—USA_English (nna) 06/29/07—debbie X

WARNING LIGHTS

or

Anti-lock Braking System (ABS) warning light

When the ignition switch is in the ON position, the Anti-lock Braking System (ABS) warning light illuminates and then turns off. This indicates the ABS is operational.

If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is not functioning properly. Have the system checked by a NISSAN dealer.

If an ABS malfunction occurs, the anti-lock func- tion is turned off. The brake system then operates normally, but without anti-lock assistance. See 9Brake system9 in the 9Starting and driving9 sec- tion.

or

Brake warning light

This light functions for both the parking brake and the foot brake systems. Parking brake indicator

When the ignition key is in the ON position, the light comes on when the parking brake is applied.

2-8 Instruments and controls

Low brake fluid warning light

When the ignition key is in the ON position, the light warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the vehicle and perform the following:

1. Check the brake fluid level. Add brake fluid as necessary. See (cid:147)Brake fluid(cid:148) in the (cid:147)Main- tenance and do-it-yourself(cid:148) section of this