2004 Nissan Quest Owners Manual

money. However, some day-to-day and regular maintenance is essential to maintain your NIS- SAN(cid:146)s good mechanical condition, as well as its emission and engine performance.

It is the owner(cid:146)s responsibility to make sure that the scheduled maintenance, as well as general maintenance, is performed.

As the vehicle owner, you are the only one who can ensure that your vehicle receives proper maintenance. You are a vital link in the mainte- nance chain. Scheduled maintenance

For your convenience, both required and optional scheduled maintenance items are described and listed in your (cid:147)NISSAN Service and Maintenance Guide.(cid:148) You must refer to that guide to ensure that necessary maintenance is performed on your NISSAN at regular intervals. General maintenance

General maintenance includes those items which should be checked during normal day-to-day op- eration. They are essential for proper vehicle op- eration. It is your responsibility to perform these maintenance procedures regularly as prescribed. 8-2 Maintenance and do-it-yourself

Performing general maintenance checks requires minimal mechanical skill and only a few general automotive tools. These checks or inspections can be done by you, a qualified technician, or, if you prefer, a NISSAN dealer. Where to go for service If maintenance service is required or your vehicle appears to malfunction, have the systems checked and corrected by a NISSAN dealer. NISSAN technicians are well-trained specialists who are kept up-to-date with the latest service information through technical bulletins, service tips, and in-dealership training programs. They are completely qualified to work on NISSAN ve- hicles before they work on your vehicle, rather than after they have worked on it. You can be confident that a NISSAN dealer(cid:146)s service department performs the best job to meet the maintenance requirements on your vehicle (cid:151) in a reliable and economic way.

During the normal day-to-day operation of the vehicle, general maintenance should be per- formed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smells, be sure to check for the cause or have a NISSAN dealer do it promptly. In addition, you should notify a NISSAN dealer if you think that repairs are required.

When performing any checks or maintenance work, closely observe the (cid:147)Maintenance precau- tions(cid:148) later in this section. EXPLANATION OF GENERAL MAINTENANCE ITEMS information on the following Additional items with (cid:147)*(cid:148) is found later in this section. Outside the vehicle The maintenance items listed here should be performed from time to time, unless otherwise specified. Doors and engine hood Check that the doors and engine hood operate properly. Also ensure that all latches lock securely. Lubricate hinges, latches, latch pins, rollers and links as necessary. Make sure that the secondary latch keeps the hood from opening when the primary latch is released.

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

When driving in areas using road salt or other corrosive materials, check lubrication frequently. Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Road wheel nuts* When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary. Tire rotation* Tires should be rotated every 7,500 miles (12,000 km). Tires* Check the pressure with a gauge often and always prior to long distance trips. If neces- sary, adjust the pressure in all tires, including the spare, to the pressure specified. Check carefully for damage, cuts or excessive wear. Wheel alignment and balance If the vehicle should pull to either side while driving on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for wheel alignment. If the steering wheel or seat vibrates at normal highway speeds, wheel balancing may be needed. c For additional

information regarding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Safety Information(cid:148) (Canada) in the Warranty Information Booklet .

Windshield Clean the windshield on a regular basis. Check the windshield at least every six months for cracks or other damage. Have a dam- aged windshield repaired by a qualified repair facility. Windshield wiper blades* Check for cracks or wear if they do not wipe properly. Inside the vehicle The maintenance items listed here should be checked on a regular basis, such as when per- forming periodic maintenance, cleaning the ve- hicle, etc. Additional information on the following items with an (cid:147)*(cid:148) is found later in this sec- tion.

Accelerator pedal Check the pedal for smooth operation and make sure the pedal does not bind or require uneven effort. Keep the floor mat away from the pedal. Automatic transmission P (Park) position mechanism On a fairly steep hill check that your vehicle is held securely with the selector lever in the P position without applying any brakes. Brake pedal and booster* Check the pedal for smooth operation and make sure it has the proper distance under it when depressed fully. Check

the brake booster function. Be certain to keep the floor mat away from the pedal. Brakes Check that the brakes do not pull the vehicle to one side when applied. Parking brake* Check that the lever has the proper travel and confirm that your vehicle is held securely on a fairly steep hill with only the parking brake applied. Seats Check seat position controls such as seat adjusters, seatback recliner, etc. to ensure they operate smoothly and all latches lock securely in every position. Check that the head restraints move up and down smoothly and the locks (if so equipped) hold securely in all latched positions. Seat belts Check that all parts of the seat belt system (for example, buckles, anchors, adjusters and retractors) operate properly and smoothly, and are installed securely. Check the belt web- bing for cuts, fraying, wear or damage. Steering wheel Check for changes in the steer- ing system, such as excessive freeplay, hard steering or strange noises. Warning lights and chimes Make sure all warning lights and chimes are operating properly. Windshield wiper and washer* Check that the wipers and washer operate properly and that the wipers do not streak.

Maintenance and do-it-yourself 8-3

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

Underbody The underbody is frequently ex- posed to corrosive substances such as those used on icy roads or to control dust. It is very important to remove these substances from the underbody, otherwise rust may form on the floor pan, frame, fuel lines and exhaust system. At the end of winter, the underbody should be thor- oughly flushed with plain water, in those areas where mud and dirt may have accumulated. See the (cid:147)Appearance and care(cid:148) section of this manual. Windshield washer fluid* Check that there is adequate fluid in the reservoir.

Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner. Under the hood and vehicle The maintenance items listed here should be checked periodically (for example, each time you check the engine oil or refuel). 4(cid:150)speed automatic transmission fluid level* Check the level after putting the selector lever in P with the engine idling at operating temperature. Battery* Check the fluid level It should be between the MAX and MIN lines. Ve- hicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. Brake fluid levels* Make sure that the brake fluid level is between the MIN and MAX lines on the reservoir. Engine coolant level* Check the coolant level when the engine is cold. Engine drive belts* Make sure the drive belts are not frayed, worn, cracked or oily.

in each cell.

8-4 Maintenance and do-it-yourself

Engine oil level* Check the level after parking the vehicle on a level surface with the engine off. Wait more than 10 minutes for the oil to drain back into the oil pan. Exhaust system Make sure there are no loose supports, cracks or holes. If the sound of the exhaust seems unusual or there is a smell of exhaust fumes, immediately have the exhaust system inspected by a NISSAN dealer. See the carbon monoxide warning in the (cid:147)Starting and driving(cid:148) section of this manual. Fluid leaks Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been parked for a while. Water dripping from the air conditioner after use is normal. If you should notice any leaks or if gasoline fumes are evident, check for the cause and have it corrected imme- diately. Power steering fluid level* and lines Check the level when the fluid is cold, with the engine off. Check the lines for proper attachment, leaks, cracks, etc. Radiator and hoses Check the front of the radiator and clean off any dirt, insects, leaves, etc., that may have accumulated. Make sure the hoses have no cracks, deformation, rot or loose connections.

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

MAINTENANCE PRECAUTIONS

When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precau- tions which should be closely observed.

WARNING

c Park the vehicle on a level surface, ap- ply the parking brake securely and block the wheels to prevent the vehicle from moving. Move the shift selector lever to P (Park).

c Be sure the ignition key is in the OFF or LOCK position when performing any parts replacement or repairs.

c Never leave the engine or automatic transmission related component har- nesses disconnected while the ignition switch is in the ON position.

c Never connect or disconnect the battery or any transistorized component while the ignition switch is in the ON position. c Your vehicle is equipped with an auto- matic engine cooling fan. It may come on at any time without warning, even if the ignition key is in the OFF position and the

engine is not running. To avoid injury, always disconnect the negative battery cable before working near the fan.

serviced by a NISSAN dealer because the fuel lines are under high pressure even when the engine is off.

c If you must work with the engine run- ning, keep your hands, clothing, hair and tools away from moving fans, belts and any other moving parts.

c It is advisable to secure or remove any loose clothing and remove any jewelry, such as rings, watches, etc. before working on your vehicle.

c Always wear eye protection whenever

you work on your vehicle.

c If you must run the engine in an en- closed space such as a garage, be sure there is proper ventilation for exhaust gases to escape.

c Never get under the vehicle while it is supported only by a jack. If it is neces- sary to work under the vehicle, support it with safety stands.

c Keep smoking materials,

flame and sparks away from the fuel tank and battery.

c On gasoline engine models with the multiport fuel injection (MFI) system, the fuel filter or fuel lines should be

CAUTION

c Do not work under the hood while the engine is hot. Turn the engine off and wait until it cools down.

c Avoid contact with used engine oil and Improperly disposed engine coolant. oil, engine coolant and/or other vehicle fluids can damage the environment. Al- ways conform to local regulations for disposal of vehicle fluid.

This (cid:147)Maintenance and do-it-yourself(cid:148) section gives instructions regarding only those items which are relatively easy for an owner to perform. A genuine NISSAN service manual is also avail- able. See (cid:147)Owner(cid:146)s Manual/Service Manual or- der information(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual. You should be aware that incomplete or improper servicing may result in operating difficulties or excessive emissions, and could affect warranty coverage. If in doubt about any servicing, have it done by a NISSAN dealer.

Maintenance and do-it-yourself 8-5

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

ENGINE COMPARTMENT CHECK LOCATIONS

Power steering fluid reservoir Engine oil filler cap Brake fluid reservoir Air cleaner Battery Fuse/fusible link box Transmission dipstick Engine oil dipstick Radiator cap

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Fuse block 11. Windshield washer fluid reservoir 12. Coolant reservoir NOTE: Engine cover removed for clarity.

8-6 Maintenance and do-it-yourself

LII0017

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

ENGINE COOLING SYSTEM

The engine cooling system is filled at the factory with a high-quality, year-round, anti-freeze cool- ant solution. The anti-freeze solution contains rust and corrosion inhibitors; therefore, additional engine cooling system additives are not neces- sary.

WARNING

c Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator.

c The radiator is equipped with a pres- sure type radiator cap. To prevent en- gine damage, use only a genuine NISSAN radiator cap.

Outside temperature

down to

(cid:176)C

-35

(cid:176)F

-30

Demineral- ized or dis- tilled water

Genuine NISSAN Long Life Anti-freeze Coolant or equivalent

50%

50%

CAUTION

When adding or replacing coolant, be sure to use only a Genuine NISSAN Long Life Anti-freeze Coolant (green) or equivalent with the proper mixture ratio of 50% anti- freeze and 50% demineralized or distilled water. The use of other types of coolant solutions or coolant colors, such as or- ange, may damage the engine cooling system.

LDI0350

CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir when the engine is cold. If the coolant level is below the MIN level, add coolant to the MAX level. If the reservoir is empty, check the coolant level in the radiator when the engine is cold. If there is insufficient coolant in the radiator, fill the radiator with coolant up to the filler opening and also add it to the reservoir up to the MAX level. If the cooling system frequently requires coolant, have it checked by a NISSAN dealer.

Maintenance and do-it-yourself 8-7

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

ENGINE OIL

CHANGING ENGINE COOLANT A NISSAN dealer can change the engine coolant. The service procedure can be found in the NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine overheat- ing.

WARNING

c To avoid the danger of being scalded, never change the coolant when the en- gine is hot.

c Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator.

c Avoid direct skin contact with used coolant. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.

c Keep coolant out of the reach of chil-

dren and pets.

LDI0351

CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and apply

the parking brake.

2. Start the engine and let it idle until it reaches

operating temperature.

3. Turn off the engine. Wait more than 10
minutes for the oil to drain back into the oil pan.

Engine coolant must be disposed of properly. Check your local regulations.

4. Remove the dipstick and wipe it clean. Re-

insert it all the way.

8-8 Maintenance and do-it-yourself

LDI0352
5. Remove the dipstick again and check the oil level. It should be between the H (High) and L (Low) marks sB . This is the normal oper- ating oil level range. If the oil level is below the L (Low) mark sA , remove the oil filler cap and pour recommended oil through the opening. Do not overfill sC .

6. Recheck oil level with the dipstick. It is normal to add some oil between oil maintenance intervals or during the break-in period, depending on the severity of operating conditions.

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

CAUTION

Oil level should be checked regularly. Op- erating the engine with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty.

If the oil filter is to be changed, remove and replace it at this time. See (cid:147)Changing engine oil filter(cid:148) later in this section.

WARNING

c Prolonged and repeated contact with used engine oil may cause skin cancer. c Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible.

c Keep used engine oil out of reach of

children.

CAUTION

Be careful not to burn yourself. The engine oil may be hot.

c Waste oil must be disposed of prop-

erly.

c Check your local regulations.

6. Clean and reinstall the drain plug and a new washer. Securely tighten the drain plug with a wrench. Do not use excessive force. Drain plug tightening torque: 22 - 29 ft-lb (29 - 39 N•m)

Maintenance and do-it-yourself 8-9

WDI0216

CHANGING ENGINE OIL 1. Park the vehicle on a level surface and apply

the parking brake.

2. Start the engine and let it idle until it reaches

operating temperature, then turn it off.

3. Remove the oil filler cap by turning it coun-

terclockwise.

4. Place a large drain pan under the drain plug.

5. Remove the drain plug with a wrench by turning it counterclockwise and completely drain the oil.

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

and

(cid:147)Capacities

7. Refill engine with recommended oil through the oil filler opening, then install the oil filler cap securely. See recommended fuel/lubricants(cid:148) in the (cid:147)Technical and con- sumer information(cid:148) section of this manual for drain and refill capacity. The drain and refill capacity depends on the oil temperature and drain time. Use these specifications for reference only. Always use the dipstick to determine when the proper amount of oil is in the engine.

5. Wipe the engine oil filter mounting surface

with a clean rag. Be sure to remove any old gasket material remaining on the mounting surface of the engine.

6. Coat the gasket on the new filter with clean

engine oil.

7. Screw on the oil filter until a slight resistance

is felt, then tighten an additional 2/3 turn.

8. Start

the engine and check for leakage

around the oil filter. Correct as required.

9. Turn the engine off and wait more than 10
minutes. Check the oil level. Add engine oil if necessary.

8. Start the engine. Check for leakage around the drain plug and oil filter. Correct as re- quired.

9. Turn the engine off and wait more than 10
minutes. Check the oil level with the dipstick. Add engine oil if necessary.

8-10 Maintenance and do-it-yourself

CHANGING ENGINE OIL FILTER 1. Park the vehicle on a level surface and apply

WDI0218

the parking brake.

2. Turn the engine off.

3. Place a large drain pan under the oil filter.

4. Loosen the oil filter with an oil filter wrench by turning it counterclockwise. Then remove the oil filter by turning it by hand.

CAUTION

Be careful not to burn yourself. The engine oil may be hot.

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

4-SPEED AUTOMATIC TRANSMISSION FLUID

WARNING

c When the engine is running, keep hands, jewelry and clothing away from any moving parts such as the cooling fan and drive belts.

c Automatic transmission fluid is poison- ous and should be stored carefully in marked containers out of the reach of children.

c The fluid can be checked at fluid tempera- tures of 86 - 122(cid:176)F (30 - 50(cid:176)C) using the COLD range on the dipstick after the engine is warmed up and before driving. However, the fluid should be re-checked using the HOT range.

1. Park the vehicle on a level surface and set

the parking brake.

2. Start the engine and then move the shift selector lever through each gear range, end- ing in P (Park).

3. Check the fluid level with the engine idling.

LDI0353

TEMPERATURE CONDITIONS FOR CHECKING c The fluid level should be checked using the HOT range on the dipstick after the following conditions have been met:

(cid:150) The engine should be warmed up to op-

erating temperature.

(cid:150) The vehicle should be driven at least 5

minutes.

(cid:150) The automatic transmission fluid should be warmed to 122 - 176(cid:176)F (50 - 80(cid:176)C).

Maintenance and do-it-yourself 8-11

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

5-SPEED AUTOMATIC TRANSMISSION FLUID

When checking or replacement is required, we recommend your NISSAN dealer for servicing.

WARNING

c Use only Genuine Nissan Matic K ATF.

Do not mix with other fluids.

c Using automatic transmission fluid other than Genuine Nissan Matic K ATF will cause deterioration in driveability and automatic transmission durability, and may damage the automatic trans- mission, which is not covered by the NISSAN new vehicle limited warranty.

The specified automatic transmission fluid is also described on caution labels located in the engine compartment.

CAUTION

DO NOT OVERFILL. Use ONLY Genuine Nissan Matic D ATF (Continental U.S. and Alaska) or Canada NISSAN Automatic Transmission Fluid. Dexron(cid:153) III/Mercon(cid:153) or equivalent may also be used. Outside the continental United States and Alaska contact a NISSAN dealership for more in- in- formation regarding suitable fluids, cluding brand(s) of Dexron(cid:153) III/Mercon(cid:153) automatic trans- mission fluid.

recommended

NOTE: If the vehicle has been driven for a long time at high speeds, or in city traffic in hot weather, or if it is being used to pull a trailer, the fluid level cannot be read accu- rately. You should wait until the fluid has cooled down (about 30 minutes) before checking fluid level.

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

WDI0334
4. Remove the dipstick and wipe it clean with

lint-free paper.

5. Reinsert the dipstick into the dipstick tube

as far as it will go.

6. Remove the dipstick and note the reading. If the automatic transmission fluid level is within the normal operating range sB , no additional fluid is required. If the fluid level is low sA add fluid through the dipstick tube.

8-12 Maintenance and do-it-yourself

POWER STEERING FLUID

BRAKE FLUID

c Recommended

is NISSAN PSF or equivalent.

fluid

Genuine

to

For further brake fluid specification information, refer recommended fuel/lubricants(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual.

(cid:147)Capacities

and

WDI0256
The fluid level should be checked using the HOT MAX range on the power steering fluid reservoir at fluid temperatures of 122(cid:176) - 176(cid:176)F (50(cid:176) - 80(cid:176)C) or using the COLD MAX range on the power steering fluid reservoir at fluid tempera- tures of 32(cid:176) - 86(cid:176)F (0(cid:176) - 30(cid:176)C).

If the fluid is below the MIN line, add Genuine NISSAN PSF fluid. Remove the cap and fill through the opening.

CAUTION

c DO NOT OVERFILL.

WARNING

Use only new fluid from a sealed con- tainer. Old, inferior or contaminated fluid may damage the brake system. The use of improper fluids can damage the brake system and affect the vehicle(cid:146)s stopping ability.

CAUTION

Do not spill the fluid on any painted sur- faces. This will damage the paint. If fluid is spilled, immediately wash the surface with water.

Maintenance and do-it-yourself 8-13

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

WINDOW WASHER FLUID

LDI0354

LDI0355

BRAKE FLUID Check the brake fluid level in the reservoir. If the fluid level is below the MIN line or the brake warning light comes on, add Genuine NISSAN Super Heavy Duty Brake Fluid or equivalent DOT 3 fluid up to the MAX line. If fluid must be added frequently, the system should be checked by a NISSAN dealer.

WINDOW WASHER FLUID RESERVOIR Fill the window washer fluid reservoir periodically. Add window washer fluid when the light comes on.

To fill the window washer fluid reservoir, lift the cap off the reservoir tank and pour the window washer fluid into the tank opening.

Add a washer solvent to the washer for better cleaning. In the winter season, add a windshield washer antifreeze. Follow the manufacturer(cid:146)s in- structions for the mixture ratio.

8-14 Maintenance and do-it-yourself

Refill the reservoir more frequently when driving conditions require an increased amount of win- dow washer fluid. Recommended fluid is Genuine NISSAN Wind- shield Washer Concentrate Cleaner & Anti- freeze or equivalent.

CAUTION

c Do not substitute engine anti-freeze coolant for window washer solution. This may result in damage to the paint. c Do not fill the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reser- voir tank.

c Pre-mix washer fluid concentrates with water to the manufacturer(cid:146)s recom- mended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concen- trate and water.

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

BATTERY

c Keep the battery surface clean and dry. Any corrosion should be washed off with a solu- tion of baking soda and water.

c Make certain the terminal connections are

clean and securely tightened.

c If the vehicle is not to be used for 30 days or longer, disconnect the negative (-) battery terminal cable to prevent discharge.

WARNING

c Do not expose the battery to flames or electrical sparks. Hydrogen gas gener- ated by the battery is explosive. Do not allow battery fluid to contact your skin, eyes, fabrics or painted surfaces. After touching a battery or battery cap, do not touch or rub your eyes. Thoroughly wash your hands. If the acid contacts your eyes, skin or clothing, immediately flush with water for at least 15 minutes and seek medical attention.

c Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the battery which can generate heat, reduce bat- tery life, and in some cases lead to an explosion.

c When working on or near a battery, al- ways wear suitable eye protection and remove all jewelry.

c Battery posts, terminals and related ac- cessories contain lead and lead com- pounds. Wash hands after handling.

c Keep battery out of

children.

the reach of

WDI0224
1. Remove the battery caps with a screwdriver as shown. Use a cloth to protect the battery case.

Maintenance and do-it-yourself 8-15

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

DRIVE BELTS

Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP STARTING If jump starting is necessary, see (cid:147)Jump starting(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN dealer.

WDI0226

Power steering fluid pump

1. 2. Crankshaft 3. Generator 4.

Air conditioner

2. Check the fluid level

LDI0302
If it is necessary to add fluid, add only distilled water to bring the level up to the bottom of the filler opening. Do not overfill.

in each cell

8-16 Maintenance and do-it-yourself

WARNING

Be sure the ignition key is in the OFF or LOCK position. The engine could rotate unexpectedly.

1. Visually inspect each belt for signs of un- usual wear, cuts, fraying or looseness. If the belt is in poor condition or is loose, have it replaced or adjusted by a NISSAN dealer.

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

2. Have the belts checked regularly for condi- tion and tension in accordance with the maintenance the (cid:147)NISSAN Service and Maintenance Guide(cid:148).

schedule

found

in

WARNING

Be sure the engine and ignition switch are off and that the parking brake is engaged securely.

CAUTION

Be sure to use the correct socket to re- move the spark plugs. An incorrect socket can damage the spark plugs.

replacement

If NISSAN dealer for assistance.

is required, please see your

SPARK PLUGS

WDI0005

REPLACING SPARK PLUGS Platinum-tipped spark plugs It is not necessary to replace platinum-tipped spark plugs as frequently as conventional type spark plugs because they last much longer. Fol- low the maintenance schedule, but do not reuse the spark plugs by cleaning or regapping. c Always replace spark plugs with rec-

ommended or equivalent ones.

Maintenance and do-it-yourself 8-17

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

IN-CABIN MICROFILTER The in-cabin microfilter restricts the entry of air- borne dust and pollen particles and reduces some objectionable outside odors. The filter is located behind the glove box. Refer to the (cid:147)NISSAN Service and Maintenance Guide(cid:148) for change intervals. If replacement is required, see your NISSAN dealer.

WARNING

c Operating the engine with the air cleaner removed can cause you or oth- ers to be burned. The air cleaner not only cleans the air, it stops the flame if the engine backfires. If it isn(cid:146)t there, and the engine backfires, you could be burned. Do not drive with the air cleaner removed, and be careful when working on the engine with the air cleaner removed.

c Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury.

AIR CLEANER

LDI0357
The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance intervals shown in the (cid:147)NISSAN Service and Maintenance Guide.(cid:148) When replacing the filter, wipe the inside of the air cleaner filter housing and the cover with a damp cloth.

Loosen the screw.

To remove the air cleaner filter: s1
s2 Disconnect the electrical connector. s3 Push down on the clips and remove the air cleaner cover. Remove the air cleaner filter.

8-18 Maintenance and do-it-yourself

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

WINDSHIELD WIPER BLADES

CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water. Clean each blade by wiping it with a cloth soaked in a washer solution or a mild detergent. Then rinse the blades with clear water. If your wind- shield is still not clear after cleaning the blades and using the wiper, replace the blades.

CAUTION

Worn windshield wiper blades can dam- age the windshield and impair driver vision.

REPLACING Replace the wiper blades if they are worn. s1
Lift the wiper arm away from the windshield. s2 Push the release tab, then move the wiper

blade down the wiper arm to remove.

s3 Remove the wiper blade.

4.

WDI0194
Insert the new wiper blade onto the wiper arm until it clicks into place.

CAUTION

c After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened.

c Make sure the wiper blades contact the glass; otherwise the arms may be dam- aged from wind pressure.

Maintenance and do-it-yourself 8-19

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

WDI0337
Be careful not to let anything get into the washer nozzle sA . This may cause clogging or improper windshield washer operation. If something gets into the nozzle, remove it with a needle or small pin sB .

8-20 Maintenance and do-it-yourself

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

Rear window wiper blade s1

Lift the wiper arm away from the rear win- dow.

LDI0356

s2 Push the wiper blade in and pivot until the

s3

blade becomes free. Insert a new blade onto the wiper arm and snap into place.

Maintenance and do-it-yourself 8-21

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

PARKING BRAKE AND BRAKE PEDAL

WDI0293

WDI0229

CHECKING PARKING BRAKE From the released position, firmly push the park- ing brake down. If the number of clicks is out of the range listed, see a NISSAN dealer. c 6(cid:150)7 clicks under depressing force of 44 lb

(196 N).

CHECKING BRAKE PEDAL With the engine running, check the distance A between the upper surface of the pedal and the metal floor. If it is out of the range shown, see a NISSAN dealer. Distance A: Under depression force of 110 lb (490 N)

3 1/2 in (90 mm) or more Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes.

8-22 Maintenance and do-it-yourself

The front and rear disc-type brakes self-adjust every time the brake pedal is applied.

WARNING

See a NISSAN dealer for a brake system check if the brake pedal height does not return to normal. Brake pad wear indicators The disc brake pads on your vehicle have audible wear indicators. When a brake pad requires re- placement, a high pitched scraping or screech- ing sound will be heard when the vehicle is in motion. The noise will be heard whether or not the brake pedal is depressed. Have the brakes checked as soon as possible if the wear indicator sound is heard. Under some driving or climate conditions, occa- sional brake squeak, squeal or other noise may be heard. Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system. Proper brake inspection intervals should be followed. For more information regarding brake inspections, see the appropriate mainte- nance schedule information in the (cid:147)NISSAN Ser- vice and Maintenance Guide(cid:148).

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

BRAKE BOOSTER Check the brake booster function as follows: 1. With the engine off, press and release the brake pedal several times. When brake pedal movement (distance of travel) remains the same from one pedal application to the next, continue on to the next step.

2. While depressing the brake pedal, start the engine. The pedal height should drop a little. 3. With the brake pedal depressed, stop the engine. Keep the pedal depressed for about 30 seconds. The pedal height should not change.

4. Run the engine for one minute without de- pressing the brake pedal, then turn it off. Depress the brake pedal several times. The pedal travel distance will decrease gradually with each depression as the vacuum is re- leased from the booster.

If the brakes do not operate properly, have the brakes checked by a NISSAN dealer.

FUSES

3. Remove the fuse box cover by pushing the

tab and lifting the cover up.

4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment.

LDI0358

ENGINE COMPARTMENT

CAUTION

Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.

If any electrical equipment does not come on, check for an open fuse.

1. Be sure the ignition switch and the headlight

switch are OFF.

2. Open the engine hood.

Maintenance and do-it-yourself 8-23

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

4.

If the fuse is open, replace it with a known good fuse.

5. Push the fuse box cover to install. 6.

If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.

5. 6.

WDI0200
If the fuse is open, replace it with a new fuse. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.

Fusible links If the electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace with only genuine NISSAN parts.

8-24 Maintenance and do-it-yourself

LDI0359

PASSENGER COMPARTMENT

CAUTION

Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire.

If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and the headlight

switch are OFF.

2. Pull the fuse box cover to remove. 3. Remove the fuse with the fuse puller.

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

KEYFOB BATTERY REPLACEMENT

Replace the battery in the keyfob as follows: s1 Open the lid using a coin. s2 Remove the battery.

s3

LPD0214
Install a new battery with the (cid:147)+(cid:148) facing down.

Recommended battery: Sanyo CR2025 or equivalent. s4 Close the lid securely.

5. Press the LOCK button, then the UNLOCK button two or three times to check the key- fob operation.

If the battery is removed for any reason other than replacement, perform step 5. c An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. c The keyfob is water-resistant; how- ever, if it does get wet, immediately wipe completely dry.

c The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle. This range may vary with conditions.

FCC Notice: Changes or modifications not expressly ap- proved by the manufacturer for compliance could void the user(cid:146)s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device.

Maintenance and do-it-yourself 8-25

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

LIGHTS

HEADLIGHTS The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb. If replacement is required, see your NISSAN dealer.

CAUTION

c High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.

c When handling the bulb, do not touch

the glass envelope.

c DO NOT TOUCH THE BULB c Use the same number and wattage as

originally installed: Low beam:

Wattage: 51
Bulb no.: 9006*

High beam:

Wattage: 60
Bulb no.: 9005*

*: Always check with the Parts Depart- ment at a NISSAN dealer for the latest parts information.

8-26 Maintenance and do-it-yourself

c Do not leave the bulb out of the fog light for a long period of time as dust, mois- ture and smoke may enter the fog light body and affect the performance of the fog light.

c Do not leave the bulb out of the head- light reflector for a long period of time as dust, moisture and smoke may enter the headlight body and affect the per- formance of the headlight.

c Aiming is not necessary after replacing the bulb. When aiming adjustment is necessary, contact a NISSAN dealer.

FOG LIGHTS (if so equipped) Replacing the fog light bulb

CAUTION

c High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.

c When handling the bulb, do not touch

the glass envelope.

c Use the same number and wattage as

originally installed: Wattage 55 Bulb No. H11* *: Always check with the Parts Depart- ment at a NISSAN dealer for the latest parts information.

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

Item

Wattage (W)

Bulb No.

Step light Cargo light High-mounted stop light* Rear combination light

Tail/Stop Backup (reversing) Turn

License plate light*

3.8

13

7/27
18
27

194
N1J

912

3157K 921K 3156K H5H

*: See a NISSAN dealer for replacement. Always check with the Parts Department at a NISSAN dealer for the latest parts information.

4. Rotate the bulb counterclockwise and re-

move.

5. Remove by pulling it straight out of the fog light assembly. Do not shake or rotate the bulb when removing it. Do not touch the glass envelope.

Install in the reverse order of removal.

6. EXTERIOR AND INTERIOR LIGHTS

Item

Wattage (W)

Bulb No.

Headlight assembly

High Low* Park/Turn* Cornering* Front fog light Puddle lamp* Room/map lights Personal lights Base model Airplane type

Footwell Glove box light Vanity mirror light*

60
51
8/29
27
55

3.4
3.4
1.32

HB3/9005
HB4/9006

3457
3156
H11
(cid:151)

PLW 578

TS578
2GL T2P

158
158
(cid:151)

Maintenance and do-it-yourself 8-27

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

LDI0362

1. Disconnect the negative (-) battery cable.

2. Remove the three splash shield screws and

move the splash shield out of the way.

3. Disconnect the bulb connector.

Room/map light Front personal lights Step light Puddle lamp

1. 2. 3. 4. 5. High-mount stoplight 6. Cargo light 7. 8. 9. Headlight assembly 10. Fog light

License plate light Rear combination light

WDI0263

Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, lamp and/or cover.

first remove the lens,

Indicates bulb removal Indicates bulb installation

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

8-28 Maintenance and do-it-yourself

LDI0360

Room/map lights

Use a cloth s1 to protect the housing.

Personal lights (cid:150) Type A Use a cloth s1 to protect the housing.

Personal lights (cid:150) Type B Use a cloth s1 to protect the housing.

LDI0363

LDI0364

LDI0365

Maintenance and do-it-yourself 8-29

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

Use a cloth s1 to protect the housing.

Step light

Use a cloth s1 to protect the housing.

Cargo light

LDI0341

LDI0366

8-30 Maintenance and do-it-yourself

Rear combination light

LDI0367

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

WHEELS AND TIRES

WDI0210
If you have a flat tire, see the (cid:147)In case of emergency(cid:148) section of this manual. TIRE PRESSURE Tire inflation pressure Check the tire pressures (including the spare) often and always prior to long distance trips. The recommended tire pressure specifications are shown on the Tire and Loading Information label under the 9Recommended Cold Tire Inflation Pressure9 heading. The Tire and Loading Infor- mation label is affixed to the driver side center pillar. Tire pressures should be checked regularly because:

c Most tires naturally lose air over time. c Tires can lose air suddenly when driven over potholes or other objects or if the vehicle strikes a curb while parking.

The tire pressures should be checked when the tires are cold. The tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds. Incorrect tire pressure, including under in- flation, may adversely affect tire life and vehicle handling.

WARNING

c Improperly inflated tires can fail sud-

denly and cause an accident.

c The vehicle weight capacity is indicated on the Tire and Loading Information label. Do not load your vehicle beyond this capacity. Overloading your vehicle may result in reduced tire life, unsafe operating conditions due to premature tire failure, or unfavorable handling characteristics and could also lead to a serious accident. Loading beyond the specified capacity may also result in failure of other vehicle components.

c Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level.

c Do not drive your vehicle over 85 MPH (137 km/h) unless it is equipped with high speed rated tires. Driving faster than 85 MPH (137 km/h) may result in tire failure, loss of control and possible injury.

c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

Low tire pressure warning system The low tire pressure warning system displays the tire pressure of all tires (except the spare tire) on the display screen by sending a signal from a sensor that is installed in each wheel. For more details, refer to (cid:147)Low tire pressure warning light(cid:148) in the (cid:147)Instruments and controls(cid:148) section, (cid:147)Low tire pressure warning system(cid:148) in the (cid:147)Starting and driving(cid:148) section, and (cid:147)Flat tire(cid:148) in the (cid:147)In case of emergency(cid:148) section. The low tire pressure warn- ing system will activate only when the vehicle is driven at speeds above 20 MPH (32 km/h).

Maintenance and do-it-yourself 8-31

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

Tire and loading information label (for US) s1 Seating capacity: The maximum number of occupants that should be seated in the ve- hicle.

s2 Vehicle load limit: See loading information in information

the Technical and consumer section.

s3 Original tire size: The size of the tires origi- nally installed on the vehicle at the factory.

8-32 Maintenance and do-it-yourself

LDI0392
s4 Recommended cold tire inflation pressure: Inflate the tires to this pressure when the tires are cold. Tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6
km) at moderate speeds. The recommended cold tire inflation is set by the manufacturer to provide the best tire wear and vehicle handling characteristics based on the ve- hicles GVWR.

s5 Tire size (cid:150) refer to (cid:147)Tire labeling(cid:148) later in this

s6

section. and s7 . Spare tire size or compact spare tire size (if so equipped)

LDI0393

Checking tire pressure 1. Remove the valve stem cap from the tire.

2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem sideways, or air will escape. If the hissing of air escaping from the tire is heard while checking the pressure, reposi- tion the gauge to eliminate this leakage.

3. Remove the gauge.

4. Read the tire pressure on the gauge stem and compare to the specification shown on the Tire and Loading Information label.

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Recheck the pressure and add or release air as needed. Install the valve stem cap.

6. 7. Check the pressure of all other tires, includ-

ing the spare.

Size

P225/65/R16
P225/60/R17
P225/65/R16
P225/60/R17
T135/80D16

Cold Tire Infla- tion Pressure 240 kPa, 35 PSI

240 kPa, 35 PSI

420 kPa, 60 PSI

Front Original Tire Rear Original Tire Spare Tire

WDI0394

TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall.

Maintenance and do-it-yourself 8-33

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

WDI0395
6. Two- or three-digit number: This number is the tire(cid:146)s load index. It is a measurement of how much weight each tire can support. You may not find this information on all tires be- cause it is not required by law.

7. Tire speed rating. You should not drive the

vehicle faster than the tire speed rating.

(1) Tire size (example: P215/65R15 95H) 1. P: The 9P9 indicates the tire is designed for

passenger vehicles.

2. Three-digit number: This number gives the width in millimeters of the tire from sidewall edge to sidewall edge.

3. Two-digit number: This number, known as the aspect ratio, gives the tire(cid:146)s ratio of height to width.

4. R: The 9R9 stands for radial. 5. Two-digit number: This number is the wheel

or rim diameter in inches.

8-34 Maintenance and do-it-yourself

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

(2) TIN (Tire Identification Number) for a new tire (example: DOT XX XX XXX XXXX) 1. DOT: Abbreviation for the 9Department Of Transportation.9 The symbol can be placed above, below or to the left or right of Tire Identification Number.

2. Two-digit code: Manufacturer(cid:146)s identifica-

tion mark

3. Two-digit code: Tire size

4. Three-digit code: Tire type code (Optional)

5. Three-digit code: Date of Manufacture

WDI0396
6. Four numbers represent the week and year the tire was built. For example, the numbers 3103 means the 31st week of 2003.

(3) Tire ply composition and material

The number of layers or plies of rubber-coated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. (4) Maximum permissible inflation pressure This number is the greatest amount of air pres- sure that should be put in the tire. Do not exceed the maximum permissible inflation pressure. (5) Maximum load rating

This number indicates the maximum load in kilo- grams and pounds that can be carried by the tire. When replacing the tires on the vehicle, always use a tire that has the same load rating as the factory installed tire. (6) Term of (cid:148)tubeless(cid:148) or (cid:148)tube type(cid:148) Indicates whether the tire requires an inner tube ((cid:147)tube type(cid:148)) or not ((cid:147)tubeless(cid:148)). (7) The word (cid:148)radial(cid:148) The word 9radial9 is shown if the tire has radial structure. (8) Manufacturer or brand name Manufacturer or brand name is shown. Other Tire-related Terminology In addition to the many terms that are defined throughout Intended Outboard Sidewall is (1) the sidewall that contains a white- wall, bears white lettering or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or (2) the outward facing sidewall of an asymmetrical tire that has a par- ticular side that must always face outward when mounted on a vehicle.

this section,

Maintenance and do-it-yourself 8-35

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

TYPES OF TIRES

WARNING

c When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. A NISSAN dealer may be able to help you with information about tire type, size, speed rating and avail- ability. Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rat- ing of the tire. c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

All season tires NISSAN specifies All Season tires on some mod- els to provide good performance all year, includ- ing snowy and icy road conditions. All Season tires are identified by ALL SEASON and/or M&S on the tire sidewall. Snow tires have better snow traction than All Season tires and may be more appropriate in some areas.

8-36 Maintenance and do-it-yourself

Summer tires NISSAN specifies summer tires on some models to provide superior performance on dry roads. Summer tire performance is substantially re- duced in snow and ice. Summer tires do not have the tire traction rating (cid:147)M&S(cid:148) on the tire sidewall.

If you do not,

If you plan to operate your vehicle in snowy or icy conditions, NISSAN recommends the use of SNOW tires or ALL SEASON tires on all four wheels. Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. it can adversely affect the safety and handling of your vehicle. Generally, snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never ex- ceed the maximum speed rating of the tire. If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing

studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer(cid:146)s suggestions. Use only SAE class (cid:147)S(cid:148) chains. Class (cid:147)S(cid:148) chains are used on vehicles with restricted tire to vehicle clearance. Vehicles that can use Class (cid:147)S(cid:148) chains are de- signed to meet the minimum clearances between the tire and the closest vehicle suspension or body component required to accommodate the use of a winter traction device (tire chains or cables). The minimum clearances are determined using the factory equipped tires. Other types may damage your vehicle. Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the pos- sibility of whipping action damage to the fenders or underbody. If possible, avoid fully loading your vehicle when using tire chains. In addition, drive at a reduced speed. Otherwise, your vehicle may be damaged and/or vehicle handling and perfor- mance may be adversely affected.

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

Tire chains must be installed only on the front wheels and not on the rear wheels. Never install tire chains on a TEMPORARY USE ONLY spare tire. Do not use tire chains on dry roads. Driving with chains in such conditions can cause damage to the various mechanisms of the vehicle due to some overstress.

The wheel nuts must be kept tightened to specifications at all times. It is recom- mended that wheel nuts be tightened to specification at each tire rotation interval.

WARNING

c After rotating the tires, check and ad-

just the tire pressure.

c Retighten the wheel nuts when the ve- hicle has been driven for 600 miles (1,000 km) (also in cases of a flat tire, etc.).

c Do not include the spare tire in the tire

rotation.

c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

WDI0258

CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km).

See (cid:147)Flat tire(cid:148) in the (cid:147)In case of emergency(cid:148) section of this manual for tire replacing proce- dures. As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench.

Wheel nut tightening torque:

83 ft-lb (112 N•m)

Maintenance and do-it-yourself 8-37

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

c The original tires have built-in tread wear indicators. When the wear indica- tors are visible, the tire(s) should be replaced.

c Improper service of the spare tire may result in serious personal injury. If it is necessary to repair the spare tire, con- tact a NISSAN dealer.

c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in (cid:147)Wheels and tires(cid:148) in the (cid:147)Technical and consumer information(cid:148) section of this manual.

WDI0259

1. Wear indicator 2. Location mark Tire wear and damage

WARNING

c Tires should be periodically inspected for wear, cracking, bulging or objects caught in the tread. If excessive wear, cracks, bulging or deep cuts are found, the tire(s) should be replaced.

8-38 Maintenance and do-it-yourself

WARNING

c The use of tires other than those recom- mended or the mixed use of tires of different brands, construction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-to- tire clearance, tire chain clearance, speedometer calibration, headlight aim and bumper height. Some of these ef- fects may lead to accidents and could result in serious personal injury.

c If the wheels are changed for any rea- son, always replace with wheels which have the same off-set dimension. Wheels of a different off-set could cause premature tire wear, degrade ve- hicle handling characteristics and/or interference brake discs/drums. Such interference can lead to decreased braking efficiency and/or early brake pad/shoe wear. Re- fer to (cid:147)Wheels and tires(cid:148) in the (cid:147)Techni- cal and consumer information(cid:148) section of for wheel off-set dimensions.

this manual

with

the

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

c When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated and the low tire pressure warning system will not function. Con- tact your NISSAN dealer as soon as possible for tire replacement and/or system resetting.

c Do not install a deformed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warning. is not

retread tires

c The use of recommended. c For additional

information regarding tires, refer to (cid:147)Important Tire Safety In- formation(cid:148) (US) or (cid:147)Tire Safety Informa- tion(cid:148) (Canada) in the Warranty Informa- tion Booklet.

Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be bal- anced as required. Wheel balance service should be per- formed with the wheels off the vehicle. Spin balancing the wheels on the vehicle could lead to mechanical damage.

c For additional information regarding tires, refer to (cid:147)Important Tire Safety Information(cid:148) (US) or (cid:147)Tire Safety Infor- mation(cid:148) (Canada) in the Warranty In- formation Booklet .

Care of wheels c Wash the wheels when washing the vehicle

to maintain their appearance.

c Clean the inner side of the wheels when the is changed or the underside of the

wheel vehicle is washed.

c Do not use abrasive cleaners when washing

the wheels.

c Inspect wheel rims regularly for dents or corrosion. Such damage may cause loss of pressure or poor seal at the tire bead.

c NISSAN recommends waxing the road wheels to protect against road salt in areas where it is used during winter.

Spare tire (TEMPORARY USE ONLY spare tire) Observe the following precautions if the TEM- PORARY USE ONLY spare tire must be used. Otherwise, your vehicle could be damaged or involved in an accident:

WARNING

c The spare tire should be used for emer- gency use only. It should be replaced with the standard tire at the first oppor- tunity to avoid possible tire or differen- tial damage.

c Drive carefully while the TEMPORARY USE ONLY spare tire is installed. Avoid sharp turns and abrupt braking while driving.

c Periodically check spare tire inflation pressure. Always keep the pressure of the TEMPORARY USE ONLY spare tire at 60 psi (420 kPa, 4.2 bar).

c With the TEMPORARY USE ONLY spare tire installed do not drive the vehicle at speeds faster than 50 MPH (80 km/h). c When driving on roads covered with snow or ice, the TEMPORARY USE ONLY spare tire should be used on the rear wheels and the original tire used on the front wheels (drive wheels). Use tire chains only on the front (original) tires.

Maintenance and do-it-yourself 8-39

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

c Tire tread of the TEMPORARY USE ONLY spare tire will wear at a faster rate than the standard tire. Replace the spare tire as soon as the tread wear indicators appear.

c Do not use the spare tire on other

vehicles.

c Do not use more than one spare tire at

the same time.

c Do not tow a trailer when the TEMPO- RARY USE ONLY spare tire is installed.

CAUTION

c Do not use tire chains on a TEMPO- RARY USE ONLY spare tire. Tire chains will not fit properly and may cause dam- age to the vehicle.

c Because the TEMPORARY USE ONLY spare tire is smaller than the original tire, ground clearance is reduced. To avoid damage to the vehicle, do not drive over obstacles. Also, do not drive the vehicle through an automatic car wash since it may get caught.

8-40 Maintenance and do-it-yourself

Z REVIEW COPY:—2004 Quest (van) Owners Manual (owners)—USA English (nna) 10/08/03—tbrooks X

9 Technical and consumer information

Capacities and recommended fuel/lubricants . . . . . . . . . 9-2
Fuel recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Engine oil and oil filter recommendation . . . . . . . . . . . 9-5
Recommended SAE viscosity number . . . . . . . . . . . . 9-6
Air conditioner system refrigerant and lubricant recommendations . . . . . . . . . . . . . . . . . . . . . . 9-6