2012 Nissan Murano Owners Manual

tion. Remove the Intelligent Key from the Intelli- gent Key port.

The ignition switch is in the ACC or ON position.

Push the ignition switch to the OFF posi- tion.

The ignition switch is in the ACC or OFF position and the selector lever is not in the P (Park) position. The Intelligent Key is inside the vehicle or cargo/trunk room area. The Intelligent Key is inside the vehicle or cargo/trunk room area. A door is not closed securely.

Move the selector lever to the P (Park) position and push the ignition switch to the OFF position.

Carry the Intelligent Key with you.

Carry the Intelligent Key with you.

Close the door securely.

When closing the trunk lid (CrossCabriolet models)

The outside chime sounds for approximately 10
seconds and the trunk lid opens.

The Intelligent Key is inside the trunk.

Carry the Intelligent Key with you.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Pre-driving checks and adjustments 3-15

REMOTE KEYLESS ENTRY SYSTEM

GUID-2CA37571-0169-4EEF-8C1B-5C2849855720

WARNING

The Intelligent Key transmits radio waves when the buttons are pushed. The FAA advises that radio waves may affect aircraft navigation and commu- nication systems. Do not operate the Intelligent Key while on an airplane. Make sure the buttons are not operated unintentionally when the unit is stored for a flight.

It is possible to lock/unlock all doors and the lift gate/trunk lid, activate the panic alarm and open the windows and lift gate/trunk lid (if so equipped) by pushing the buttons on the Intelligent Key from outside the vehicle. Before locking the doors, make sure the Intelligent Key is not left in the vehicle. The LOCK/UNLOCK button on the Intelligent Key can operate at a distance of approximately 33 ft (10 m) from the vehicle. (The effective distance depends upon the conditions around the vehicle.) As many as 4 Intelligent Keys can be used with one vehicle. For information concerning the purchase and use of additional Intelligent Keys, contact a NISSAN dealer. The lock and unlock buttons will not operate 3-16 Pre-driving checks and adjustments

when:

the distance between the Intelligent Key and the vehicle is over 33 ft (10 m). the Intelligent Key battery is discharged.

After locking with the remote keyless entry function, pull the door handle to make sure the doors are securely locked. The LOCK/UNLOCK operating range varies depending on the environment. To securely operate the lock and unlock buttons, approach the vehicle to about 3 ft (1 m) from the door.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (170,1)

SPA2252A

Type A

SPA2436

Type B

Black plate (171,1)

4. The hazard indicator flashes once again. All

the doors and the lift gate will unlock.

All doors will be locked automatically unless one of the following operations is performed within 1
minute after pushing the UNLOCK button *2 while the doors are locked. If during this 1- button *2
minute time period, the UNLOCK is pushed, all doors will be locked automatically after another 1 minute. . Opening any door (including the lift gate) or

trunk

. Pushing the ignition switch

button *2

Opening windows GUID-A6DE3912-EF46-4CEA-887C-286260C70F8F The UNLOCK operation also allows you to open the window that is equipped with the automatic open/close function. (See “Power windows” in the “2. Instruments and controls” section). To open the windows, push the door UNLOCK for about 3 seconds after the

button *2
door is unlocked. To stop opening, release the UNLOCK button *2 . Windows cannot be closed using the button on the Intelligent Key. If the window open operation is stopped in mid- operation while pushing the UNLOCK button *2 ,

release and push the UNLOCK Pre-driving checks and adjustments 3-17

HOW TO USE REMOTE KEYLESS ENTRY SYSTEM GUID-C6C8F65F-3152-4763-BF0F-A4447FDA547F When you lock or unlock the doors or the lift gate/trunk lid, the hazard indicator will flash and the horn (or the outside chime) will sound as a confirmation. For details, see “Setting hazard indicator and horn mode” later in this section.

Locking doors 1. Move the selector lever

GUID-8CBF74EB-4EC8-465A-B09B-2CA410A11EC0
to the P (Park) position and push the ignition switch to the OFF position. Make sure you carry the Intelligent Key with you.*

2. Close all the doors and lift gate. button *1 . 3. Push the LOCK 4. All the doors and the lift gate will lock. 5. The hazard indicator flashes twice and the

horn chirps once.

*:

Doors will lock while the ignition switch is in the ACC or ON position.

Unlocking doors 1. Push the UNLOCK 2. The hazard indicator

GUID-07D2F8A3-E183-47DE-B2BB-5F0B2765BABE

button *2 once. flashes once. The

driver’s door will unlock.

3. Push the UNLOCK

within 1 minute.

button *2

again

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

SPA2867

Type C

*1
*2
*3
*4
*5

LOCK button UNLOCK button Power lift gate button PANIC button TRUNK button

(if so equipped)

(CrossCabriolet models)

Black plate (172,1)

button *1

Setting hazard indicator and horn mode GUID-0B7C4602-8422-4E4E-A11F-E789553B0A3D This vehicle is set in hazard indicator and horn mode when you first receive the vehicle. In hazard indicator and horn mode, when the LOCK is pushed, the hazard indicator flashes twice and the horn chirps once. button *2
When the UNLOCK is pushed, the hazard indicator flashes once. If horns are not necessary, the system can be switched to the hazard indicator mode. In hazard indicator mode, when the LOCK button *1
flashes twice. When the UNLOCK *2
the horn operates.

the hazard indicator button is pushed, neither the hazard indicator nor

is pushed,

button *2

again until the window opens

completely. The door windows can be opened or closed by turning the mechanical key in a door lock. (See “Doors” earlier in this section.)

Opening/closing lift gate (if so equipped) button *3
1. Push the power lift gate for more than 1 second.

GUID-7A0EC3F3-A0FF-43A5-983C-6F30EE025AB4

2. The lift gate will automatically open. The hazard indicator flashes 4 times and the outside chime sounds for approximately 3
seconds. To close the lift gate, push the power lift gate

button *3 .

The lift gate will automatically close. button *3
is pushed If the power lift gate while the lift gate is being opened or closed, the lift gate will reverse. button *3 cannot be The power lift gate operated when the ignition switch is in the ON position.

Using panic alarm GUID-0EEA2C46-8F73-4264-8914-B8CE095E8B5C If you are near your vehicle and feel threatened, you can activate the alarm according to the following procedure to call attention. button *4
1. Push the PANIC than 1 second.

for more

2. The theft warning alarm will sound and the

headlights will flash for 25 seconds.

3. The panic alarm stops under either of the

following conditions. . Any of the buttons is pushed. (Note: the should be

It has run for 25 seconds, or button *4

PANIC pushed for more than 1 second.)

Opening trunk lid (CrossCabriolet mod- els) 1. Push the TRUNK

GUID-87B7F82C-E682-4BF3-BE6B-52CC949856EB on the

button *5

Intelligent Key for more than 1 second.

2. The trunk will unlatch. 3. Raise the trunk lid to open the trunk.

3-18 Pre-driving checks and adjustments

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Hazard indicator and horn mode:

GUID-D73A39BF-43C8-459F-9C24-47B7F579C407

DOOR LOCK

DOOR UNLOCK

TRUNK UNLOCK

Intelligent Key system

(Using door handle or lift gate/

trunk request switch)

HAZARD - twice OUTSIDE CHIME - twice

HAZARD - once OUTSIDE CHIME - once

HAZARD - none OUTSIDE CHIME - 4
times

Remote keyless entry sys-

(Using

tem or

button)

Hazard indicator mode:

HAZARD - twice HORN - once

HAZARD - once HORN - none

HAZARD - none HORN - none

GUID-D73A39BF-43C8-459F-9C24-47B7F579C407

DOOR LOCK

DOOR UNLOCK

TRUNK UNLOCK

Intelligent Key system

(Using door handle or lift gate/

trunk request switch)

HAZARD - twice OUTSIDE CHIME - none

HAZARD - none OUTSIDE CHIME - none

HAZARD - none OUTSIDE CHIME - none

Remote keyless entry sys-

(Using

tem or

button)

HAZARD - twice HORN - none

HAZARD - none HORN - none

HAZARD - none HORN - none

Black plate (173,1)

GUID-D73A39BF-43C8-459F-9C24-47B7F579C407

Switching procedure: and UNLOCK *2
Push the LOCK *1
buttons simultaneously for more than 2 seconds to switch the mode from one to the other. When pushing the buttons to set the hazard indicator mode, the hazard indicator flashes 3
times. When pushing the buttons to set the hazard indicator and horn mode, the hazard indicator flashes once and the horn chirps once.

NOS1695

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Pre-driving checks and adjustments 3-19

Black plate (174,1)

HOOD

LIFT GATE (Hardtop models)

GUID-EFCA6993-4C66-4840-8CB7-A8AB3D34E97F

GUID-4BA01BDD-7B7E-4674-BC74-CD9F5511DABB

WARNING

. Always be sure the lift gate has been closed securely to prevent it from opening while driving.

. Do not drive with the lift gate open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Exhaust gas (carbon monox- ide)” in the “5. Starting and driving” section of this manual.

. Do not leave children unattended inside the vehicle. They could un- knowingly activate switches or con- trols. Unattended children could become involved in serious acci- dents.

. Always be sure that hands and feet are clear of the door frame to avoid injury while closing the lift gate.

SPA2437

hood to fly open and result in an accident.

If you see steam or smoke coming from the engine compartment, to avoid injury do not open the hood.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

1. Pull

the hood lock release handle *1
the

located below the instrument panel; hood will then spring up slightly.

2. Pull the lever *2 up at the front of the hood

with your fingertips and raise the hood.

3. When closing the hood, slowly close the locks into

hood down and make sure it place.

WARNING

. Make sure the hood is completely closed and latched before driving. Failure to do so could cause the

3-20 Pre-driving checks and adjustments

Black plate (175,1)

the vehicle twice.

To close the lift gate, pull down until it securely locks. OPERATING POWER LIFT GATE (if so equipped) GUID-8341353C-675A-42F8-BB11-F9F93D73F7A6
To operate the power lift gate, the selector lever must be in the P (Park) position. The power lift gate will not operate if the battery voltage is low.

SPA2438

SPA2461

OPERATING MANUAL LIFT GATE GUID-61A6DC11-5EF1-41BC-B25F-AD72BB5A5897
To open the lift gate, unlock it and push the opener switch *A . Pull up the lift gate to open. The lift gate can be unlocked by: pushing the unlock button Intelligent Key twice. pushing the lift gate request switch (if so equipped). pushing the door handle request switch twice (if so equipped). pushing the power door lock switch to the unlock position. inserting the mechanical key into the driver’s door key cylinder and turning it to the rear of

on the

Power lift gate main switch GUID-F5D61AAE-138A-4E73-8934-59B0837383B1
The power lift gate operation can be turned on or off by the power lift gate main switch on the instrument panel. When the power lift gate main switch is pushed to the “OFF” position, the power operation is not available by the power lift gate switch on the lift gate and lift gate opener switch.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Pre-driving checks and adjustments 3-21

Black plate (176,1)

Power open GUID-4B6F9483-D240-461C-8F75-22A08D5716EE When the lift gate is fully closed, the lift gate will fully open automatically by:

pushing the power lift gate switch *A on the instrument panel pushing the lift gate opener switch *B pushing the power lift gate button *C on the Intelligent Key for more than 1 second

The hazard flashes 4 times and the outside chime sounds when the lift gate starts opening. NOTE:

*C

The lift gate can be opened by the power lift gate switch *A or the lift gate button even if the lift gate is locked. The lift gate will individually unlock and open. Once the lift gate is closed, its lock will align to the vehicle’s lock or unlock status. Power close GUID-E888CA90-E984-4CE2-975D-16E18CC2BCC1
When the lift gate is fully opened, the lift gate will fully close automatically by:

pushing the power lift gate switch *A on the instrument panel pushing the power lift gate switch *D on the lower part of the lift gate pushing the lift gate release button *C on the Intelligent Key for more than 1 second

SPA2439

SPA2463

SPA2462

SPA2440

3-22 Pre-driving checks and adjustments

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

The hazard flashes 4 times and the outside chime sounds when the lift gate starts closing.

Reverse function GUID-28EE2E95-2E6D-4231-A853-225C012F131B The power lift gate will reverse immediately if one of the following actions is performed during power open or power close.

pushing the power lift gate switch *A on the instrument panel pushing the lift gate switch *D on the lower part of the lift gate pushing the lift gate button the Intelligent Key.

*C on

The outside chime sounds when the lift gate starts to reverse. The power lift gate button on the Intelligent Key cannot be operated when the ignition switch is in the ON position.

*C

Auto reverse function GUID-588A601D-27B2-48E9-8FDE-883DF425CE62
The auto-reverse function enables the lift gate to automatically reverse when something is caught in the lift gate as it is opening or closing. When the control unit detects an obstacle, the lift gate will reverse and return to the full open or full close position. If a second obstacle is detected, the lift gate motion will stop and the drive motor will disengage. The lift gate will enter the manual

Black plate (177,1)

pushed during power open or close, the power operation will be canceled and the lift gate can be operated manually.

Pre-driving checks and adjustments 3-23

mode. A pinch sensor is mounted on each side of the lift gate. If an obstacle is detected by the pinch sensor during power close, the lift gate will reverse and return to the full open position immediately. NOTE:

If the pinch sensor is damaged or removed, the power close function will not operate.

WARNING

There is a small distance immediately before the closed position that cannot be detected. Make sure that all passen- gers keep their hands, etc., clear from the lift gate opening before closing the lift gate.

Manual mode GUID-2D066900-C91C-4239-8B7E-587EF875F5E6
If power operation is not available, the lift gate can be operated manually. Power operation may not be available if multiple obstacles have been detected in a single power cycle or if the battery voltage is low. When the power lift gate main switch is in the OFF position, the lift gate can be opened manually by pushing the lift gate opener switch. If the power lift gate opener switch is

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (178,1)

CAUTION

CAUTION

The lift gate will automatically close from a partly open position. To avoid pinching, keep hands and fingers away from lift gate opening.

. Do not let children operate the lift

gate.

If the power lift gate does not stay open or if the lift gate unexpectedly closes at any time, do not operate the lift gate. There may be a pres- sure loss in one or both of the lift gate gas stays. Have the lift gate inspected by a NISSAN dealer.

. Do not activate the power lift gate if one or both of the lift gate gas stays are removed. Damage to the lift gate or power lift gate mechanisms may occur.

AUTO CLOSURE GUID-7AD58A51-23F5-4099-B091-E857EB67A8A8
If the lift gate is pulled down to a partly open position, the lift gate will pull itself to the closed position. Do not apply excessive force when the auto closure is operating. Excessive force applied may cause the mechanism to malfunction.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

SPA2464

Safe Mode If the gas stays of the lift gate *1
GUID-9161D00E-0361-4406-9899-CE4F57ECAF0B lose pressure, the power lift gate safe mode is activated. When the safe mode is activated, the lift gate intermittently closes. Then the lift gate will be pulled to the closed and latched position by a motor. The power lift gate cannot be opened using the switches at any time in the safe mode. Do not operate the lift gate again until checked by a NISSAN dealer.

it is

3-24 Pre-driving checks and adjustments

Black plate (179,1)

TRUNK LID (CrossCabriolet models)

GUID-2C264EE5-CF00-4D99-8287-BE0FA9532E1E

WARNING

. Do not drive with the trunk lid open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Exhaust gas (carbon monox- ide)” in the “5. Starting and driving” section of this manual.

. Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured. Keep the car locked, with the trunk closed, when not in use, and prevent children’s access to Intelligent Keys.

SPA2868

GUID-3E3F75C6-3DEC-4CB3-AB7F-5D7232A3354C

TRUNK LID RELEASE SWITCH The trunk lid release switch *A is located on the instrument panel. To open the trunk lid, push the release switch down as illustrated. To close, push the trunk lid down.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Pre-driving checks and adjustments 3-25

SPA1915

GUID-1D614743-17EC-4673-B778-F929F5E10CB9
the lift gate cannot be opened due to a

LIFT GATE RELEASE If discharged battery, follow these steps. 1. Remove the cover inside of the lift gate with

a suitable tool.

2. Move the lever toward the direction *A as

illustrated to open the lift gate.

Have the vehicle checked by a NISSAN dealer.

Black plate (180,1)

SPA2866-A

SPA2871

SPA2869

TRUNK OPEN REQUEST SWITCH GUID-B01B03F7-E6F4-4880-AF56-804BF02D2CC4
The trunk lid can be opened by pushing the trunk open request switch *A when the Intelligent Key is within the operating range of the trunk lock/unlock function regardless of the inside lock knob position. (See “Intelligent Key system” earlier in this section.) TRUNK BUTTON GUID-BBA61B35-8253-481A-BABD-2C8031AD5525
The trunk lid can be opened by pushing the TRUNK button on the Intelligent Key for more than 1 second.

3-26 Pre-driving checks and adjustments

OPENING WITH KEY GUID-A6A5B4FC-5FBC-4C5F-8A27-A149CEEDAF32
To open the trunk lid, insert the mechanical key to the trunk key cylinder and turn the key to the right side of the vehicle. To close, remove the key and push the trunk lid down.

TRUNK RELEASE POWER CANCEL SWITCH GUID-4D40CB74-0EE0-44CF-9D72-61FB52259054
When the switch located inside the glove box is in the OFF position *A , the power to the trunk lid will be canceled and the trunk lid cannot be opened by the trunk lid release switch, the trunk open request switch with the Intelligent Key carried with you or the TRUNK button on the Intelligent Key. When you have to leave the vehicle with a valet and want to keep your belongings safe in the glove box and the trunk, push this switch to OFF and lock the glove box with the mechanical key. Then leave the vehicle and the Intelligent Key with the valet and keep the mechanical key with

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

you. See “Keys” earlier in this section. To connect the power to the trunk lid, push the switch to the ON *B position.

Black plate (181,1)

become locked inside the trunk or in the event of the loss of electrical power such as a dis- charged battery.

Releasing inside the trunk GUID-AF4D5EDF-174E-4F6F-B198-B456683E28BD To open the trunk lid from the inside, pull the release handle *1
until the lock releases and push up on the trunk lid. The release lever is made of a material that glows in the dark after a brief exposure to ambient light. The handle is located on the back of the trunk lid as illustrated.

Pre-driving checks and adjustments 3-27

INTERIOR TRUNK LID RELEASE

GUID-76617E49-69A3-42A3-B4CE-6BA318A11DE5

SPA2870

WARNING

Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured. Keep the car locked, with the trunk lid securely latched, when not in use, and prevent children’s access to Intelligent Keys.

The interior trunk lid release mechanism allows opening of the trunk lid in the event that people

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (182,1)

(See “Luggage cover (CrossCabriolet mod- els)” in the “2. Instruments and controls” section).

. When the selector lever is in a position other

than the R (Reverse) position.

CAUTION

Always keep the engine running while operating the soft top. The top will also operate when the ignition switch is in the ON position, but run the engine to prevent a discharged battery.

Be sure to follow the operating instructions, and all the warnings and cautions in this section. Improper operation of the top could cause a system malfunction, damage, or dete- rioration of the top material and related parts.

SOFT TOP (CrossCabriolet models)

GUID-4E386DA4-547C-4A5A-BC6A-9C85B5A124D5

SPA2872

Interior/exterior view

(on the combination

1.

2. 3. 4. 5. 6. 7. 8. 9.

light

top indicator

Soft meter) Soft top operating switch Top lock hole Soft top Rear parcel shelf Skylight glass Rear window Top storage lid Trunk lid

top of

BEFORE OPERATING THE TOP GUID-B5A72515-20E3-4BF7-986E-50FBF5D603CE The soft this vehicle is electrically operated. You can fully open or close the top only by pressing the operating switch located on the center console. Only operate the soft top operating switch under all of the following conditions: . When the trunk is closed. . When the vehicle is stopped. . When the engine is running or when the

3-28 Pre-driving checks and adjustments

ignition switch is in the ON position.

. When the luggage cover is pulled out and the roof storage area is

hooked so that separated from the trunk.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (183,1)

it while moving. The top operating system could also be damaged.

. Do not operate the top when there is not enough clearance behind the vehicle. Someone could become trapped between the top storage lid and another object (for example a wall) which could result in serious injury.

. Do not operate the top in a strong wind. It could be blown by the wind, striking someone or damageing the top.

. Do not allow anyone to stand up or extend any portion of their body out of the opening while the vehicle is in motion or while the top is being operated.

In an accident you could be thrown from the vehicle with an open top. Always use seat belts and proper child restraints.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

SPA2873

WARNING

. Park the vehicle in a safe and level place and apply the parking brake. . Make sure the parking area is clear of obstacles and there is enough clearance over the top (for example, in a garage or a covered area). More than approximately 10 ft (3 m) from the ground and more than approxi- mately 4.9 ft (1.5 m) from the rear of the vehicle is required to open or close the top safely. Otherwise, the top may damage any objects above

JVP0045X

WARNING

. Never install a cover or film (for example window tint) on the sky- light glass. This may cause the dual pop-up roll bars to operate impro- perly and could result in serious injury or death in the event of a rollover. (see “Dual pop-up roll bar system (CrossCabriolet models)” in the “1. Safety — Seats, seat belts and supplemental restraint system” section.)

Pre-driving checks and adjustments 3-29

Black plate (184,1)

. Do not place anything in the top storage area. The top will not fit there properly, and this could da- mage the top and/or the vehicle body.

. Do not sit or place anything on the top, rear parcel shelf, inner flaps, storage lid and trunk lid, especially when the top is being operated. The top may be damaged.

. Do not drive the vehicle with the top partially opened. Always make sure the top is either fully opened or closed before driving.

. Secure items so that they cannot be blown from the vehicle while driving with the top open.

. Do not operate the top manually except for emergency cases. Manual operation may damage the top.

. Be sure to fully open or fully close the top. Do not release the switch half way through the roof opening or closing process. If the top is only partially opened, significant da- mage to the top could occur.

. Do not operate the top if the dual pop-up roll bars have been acti-

CAUTION

. Do not operate the top when the temperature is below 328F (08C). This may result in damage to the top material or operating system.

. Remove water drops, snow, ice or sand from the top, and dry the surface of the top completely before opening it.

. Do not open the top when it is wet or damp. This may cause interior water damage, stains or mildew on the top material.

. Be sure to turn off the rear window defroster switch. Never turn it on while the top is being operated or fully opened. The heat may damage the top material.

SPA2691

CAUTION

. Do not place any objects between the top cloth and the structure. Doing so could interfere with top operation and cause damage to the top operating system or the objects. . Do not place anything on the top, inner flaps and rear parcel shelf, trunk lid. Even small items may interfere with the top operation and could cause damage to the top or the vehicle body.

3-30 Pre-driving checks and adjustments

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (185,1)

vated. Extended dual pop-up roll bars may interfere with top opera- tion and could cause damage to the top or the vehicle body.

Make sure the trunk lid is securely closed before operating the top.

SPA2874

SPA2875

WHEN OPERATING THE TOP

GUID-9783AAEB-D9EE-4150-9CAA-F03901BE51C6

WARNING

Keep hands and other parts of the body away from moving parts such as the top, storage lid, and power windows.

inner flap *A

CAUTION

. Keep all parts of the top linkage clear of obstructions, or the top latch may not be securely locked.

. Do not place anything in the top storage area. Cargo that contacts the top could damage the top and/ or the vehicle body. See Caution label *B attached in the trunk.

Pre-driving checks and adjustments 3-31

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (186,1)

fully opened or fully closed position. When the soft top is operating, and any of the following conditions occur, the top will stop operating. . When the selector lever is in the R (Reverse)

position.

. When the vehicle moves at a speed of 3

MPH (5 km/h) or more.

. When the battery voltage is extremely low. . When the temperature of top

the soft

system becomes extremely high.

Release the soft top operating switch, and push the switch again to move the top to the fully opened or closed position. The soft top indicator light will turn off when the top operation is completely finished. If the soft top indicator light illuminates with the ignition switch ON (whether the top is operated or not, and when the top is engaged), it may indicate the top operating system is not functioning properly. Have your vehicle checked by a NISSAN dealer as soon as possible.

NOTE:

In case of low battery or low tempera- ture, the top may temporarily stop moving during the operation. This func- tions to protect the top control me- chanism, and it is not a malfunction. The top operation may be automati- cally stopped to protect the system under the following conditions: — Immediately after the engine is

started.

— If the top or power windows are operated repeatedly in a short per- iod of time.

— If the top is left partially open for a long period of time before the top is fully opened.

Wait for approximately 5 minutes be- fore operating the top again.

LUGGAGE COVER GUID-B26A5118-9345-47A5-9852-69A71FF769AB The soft top can be operated only when the trunk is separated by the luggage cover. The luggage cover must be pulled out and hung on the hooks or the top will not operate. (See “Luggage cover (CrossCabriolet models)” in the “2. Instruments and controls” section).

3-32 Pre-driving checks and adjustments

SPA1691

SOFT TOP INDICATOR LIGHT GUID-AC0A62DC-CB4D-48FD-9A3A-3C2535153F4E The soft top indicator light in the instrument panel shows the conditions of top operation. The light illuminates when the soft top is being operated or if it is stopped before reaching the fully opened or closed position. When the top is fully opened or closed, the light will turn off. The light blinks while the soft top is not fully opened or closed under the following condi- tions: . When the vehicle is driven. . When the selector lever is in the R (Reverse)

position.

Only drive the vehicle when the soft top is in the

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

AUTOMATIC WINDOW LOWERING GUID-53158076-5049-419E-B46E-60FF9661FC5C When the soft top operating switch is pressed, the power windows will automatically be low- ered completely. The windows do not rise automatically after the top operation is com- pleted. Use the power window switches to raise them.

Black plate (187,1)

NOTE:

If you release the switch and press it again while the top is being opened, the top will slightly move to the closing direction, then start moving to the opening direction again. The top is designed to move in this way. It is not a malfunction.

SPA2632

OPENING THE TOP 1. Start the engine. 2. Push OPEN on the soft top operating switch

GUID-A212C8E0-E684-4914-9C6A-29123B5D454E

and hold it until the top is fully opened. . The soft top indicator light will illuminate while the top is in motion. (In about 20
seconds, the opening movement will finish and the indicator light turns off.)

. Windows will automatically be fully

opened.

3. Release the switch when the top is fully

opened. (The indicator light turns off.)

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Pre-driving checks and adjustments 3-33

Black plate (188,1)

OPENING THE TOP USING THE IN- TELLIGENT KEY GUID-49044D36-3539-45EB-A570-6E07681CB5C9
The soft top can be opened using the door handle request switch.

SPA2633

JVP0049X

Opening the soft top GUID-4C7A2A7D-B19A-4092-923C-63EC90103CB4
Push the ignition switch to the OFF position and make sure to carry the Intelligent Key with you. Make sure that the trunk luggage cover is pulled out and hung on the hooks. Push the door handle request switch (driver’s or passenger’s) *A and hold it until the soft top is fully open.

GUID-DAD80567-3F61-4CBF-86B1-D92B657E227A

CLOSING THE TOP 1. Start the engine. 2. Push CLOSE on the soft

top operating switch and hold it until the top is fully closed. . The soft top indicator light will illuminate while the top is in motion. (In about 20
seconds, the closing movement will finish.)

. Windows will automatically be fully

opened.

3. Release the switch when the top is fully

closed. (The indicator light will turn off.)

3-34 Pre-driving checks and adjustments

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (189,1)

TROUBLESHOOTING GUIDE If the soft top stops halfway during operation or does not operate normally, follow the procedures shown in the following table. If the procedures in the following table do not solve the symptom, immediately contact a NISSAN dealer for the inspection.

GUID-2D51144E-87AE-4042-BCCA-A9F63DED76ED

Symptom

Beep

Possible cause

Possible solution

The OPEN side of the soft top operating switch is pushed, but the soft top does not operate.

Sounds twice

The OPEN side of the soft top operating switch is pushed while the soft top is fully open, or the CLOSE side of the soft top operating switch is pushed while the soft top is fully closed.

Sounds twice

The selector lever is in the R (Reverse) position.

The trunk lid is opened.

Sounds twice Does not sound The battery voltage is low. Does not sound The operation stops to protect the system.

The soft top stops halfway during opera- tion.

Sounds twice

Objects are trapped in the moving structure of the soft top.

When the vehicle is being driven, the beep sounds.

Sounds continu-

ously

The soft top is partially opened.

Sounds twice

The battery voltage is low.

Push the CLOSE side of the soft top operating switch when the soft top is fully open. Push the OPEN side of the soft top operating switch when the soft top is fully closed. Shift the selector lever to the P (Park) or N (Neutral) position, and then operate the soft top. Fully close the trunk lid. Start the engine again and operate the soft top. Wait for approximately 5 minutes. Check that an object is not trapped inside the rear parcel shelf, inner flap and soft top. After the check, turn the ignition switch to the OFF position, start the engine again and then operate the soft top. Start the engine again and operate the soft top. Immediately park the vehicle in a safe location and fully open or fully close the soft top.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Pre-driving checks and adjustments 3-35

Black plate (190,1)

JVP0036X

a. Remove the trunk light *1 . b. Remove the lower trim clips *3

and remove the upper and lower trim pieces *2 .

c. Remove the two luggage cover hooks *4
on the left and right side of the trunk. Then disconnect the connector *5
on the left side luggage cover hook.

d. Remove the clips *6 behind the luggage

cover hooks.

IF THE TOP DOES NOT OPEN OR CLOSE ELECTRICALLY If you cannot operate the soft operating switch, following operating conditions are met. . Vehicle is stopped

GUID-17B75AAD-7BCD-4553-9A36-FB3FA5E49CAF top with the the

first check whether all

Ignition switch is ON (Run the engine when operating the top.) The trunk is closed The selector lever is in a position other than the R (Reverse) position The luggage cover is pulled out and hooked so that the roof storage area is separated from the trunk.

If the top still does not move under the above conditions or has any system malfunction, see a NISSAN dealer as soon as possible. When you must close the top by yourself, in the event of emergency or when an immediate dealer service is not available, close the top manually accord- ing to the procedures shown in this section. When closing the soft top manually: . Move the vehicle to a safe place, away from

traffic. Two people should perform this procedure, as some of the top parts are extremely heavy.

The top cannot be opened manually.

3-36 Pre-driving checks and adjustments

WARNING

. Do not drive with the top partially

opened.

If the top cannot be operated prop- erly, see a NISSAN dealer as soon as possible to have your vehicle checked.

CAUTION

The storage lid is extremely heavy. The storage lid should be manually opened or closed by two people.

1. Open the trunk lid.

In the event of a discharged battery, the secondary trunk release mechanism should be operated. (See “Trunk lid (CrossCabriolet models)” earlier in this section.)

2. Open the top storage lid.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (191,1)

*A in the direction of the arrow using a suitable tool, and release the storage lid lock *B .

NOTE: Use a cloth or other tool to protect your hands when pulling on the cables.

JVP0038X

f. Push and hold the lever *C

toward the front of the vehicle to release the storage lid.

g. Close the trunk lid.

CAUTION

Make sure to close the trunk lid before opening the storage lid. The storage lid may contact the trunk lid and damage it.

Pre-driving checks and adjustments 3-37

JVP0037X

e. Pull back the left and right side trim in the trunk room. Pull the left and right cables

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (192,1)

j. Move the inner flap *E

in the direction of the arrows, then secure the flaps with tape or string.

and *F

JVP0039X

h. With two people, manually lift the storage lid by hand on the left and right side of the vehicle at lid edge *D .

3-38 Pre-driving checks and adjustments

JVP0040X

i. Move the storage lid in the direction

marked by the arrow to open it.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (193,1)

soft top forward all the way.

JVP0041X

3. Close the soft top.

a. Pull up the soft top simultaneously from

the right and left side of the vehicle.

JVP0042X b. Lift the rear side of the soft top *A until it is out of the storage area, then open the

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Pre-driving checks and adjustments 3-39

Black plate (194,1)

JVP0043X

JVP0044X

SPA2689

c. Close the storage lid.

CAUTION

Make sure to close the storage lid completely. The storage lid may contact the soft top and damage it.

d. Close the front and rear parts of the soft

top at the same time as illustrated.

3-40 Pre-driving checks and adjustments

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

4. Lock the front part of the soft top.

a. Remove the cap *1 as illustrated. b.

Insert tool *2
the hole and turn clockwise.

(located in the trunk) into

CAUTION

. After closing the top manually, have the system checked and/or repaired by a NISSAN dealer as soon as possible.

. Avoid leaving the vehicle outside for long periods or driving at high speeds. The rear of the top is not

locked completely, and this may allow wind and rain to get into your vehicle.

CARE OF THE SOFT TOP AND THE VEHICLE BODY GUID-85248970-F9FC-4037-98ED-B29AF18639F5
To use your CrossCabriolet safely and comfor- tably, you need to observe all the warnings and cautions shown in the previous pages. Also, to maintain a good appearance of the soft top and the vehicle body, you need to care for them by cleaning and/or washing properly.

CAUTION

. Do not use an automatic car wash or a high-pressure car wash to clean your vehicle. The top may be da- maged and water may leak into the inside of the vehicle.

. Store the vehicle with the top closed if it is not to be used for long periods. Keeping the top stowed for long periods may cause wrinkles on the surface of the top.

See “Cleaning exterior” in the “7. Appearance and care” section for detailed instructions.

. A protective clear tape is applied to the top storage lid painted surface where the soft top contacts the surface. When the top is fully closed, the tape may transmit some light, visible from the inside of the vehicle. This does not affect the water and air tightness of the seal. the trunk and top The inner surface of storage lids may show a fibrous, or marbled pattern. This is the normal appearance of the material used in these parts.

Black plate (195,1)

FUEL-FILLER DOOR

GUID-58F03607-9C0E-45A3-A739-6F6533CBE06D

SPA2441

OPENING FUEL-FILLER DOOR GUID-C2164B1B-2157-4717-902B-A3E94EF3F4D7
To open the fuel-filler door, push the opener switch located below the instrument panel. To lock, close the fuel-filler door securely.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Pre-driving checks and adjustments 3-41

Black plate (196,1)

FUEL-FILLER CAP

GUID-45E9B200-5266-43FB-B114-5A04EF6FA26A

WARNING

. Gasoline is extremely flammable and highly explosive under certain conditions. You could be burned or seriously injured if it is misused or mishandled. Always stop engine and do not smoke or allow open flames or sparks near the vehicle when refueling.

. Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.

. Use only an original equipment type fuel-filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emission control sys- tem. An incorrect cap can result in a serious malfunction and possible injury. It could also cause the mal- function indicator light to come on.

3-42 Pre-driving checks and adjustments

. Never pour fuel

into the throttle body to attempt to start your vehi- cle.

. Do not fill a portable fuel container in the vehicle or trailer. Static elec- tricity can cause an explosion of flammable liquid, vapor or gas in any vehicle or trailer. To reduce the risk of serious injury or death when filling portable fuel containers:

— Always place the container on

the ground when filling.

— Do not use electronic devices

when filling.

— Keep the pump nozzle in contact with the container while you are filling it.

— Use only approved portable fuel containers for flammable liquid.

CAUTION

If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.

(MIL)

Insert the cap straight into the fuel- filler tube, then tighten the fuel-filler cap until a single click is heard. Failure to tighten the fuel-filler cap properly may cause the mal- function indicator light to illuminate. If the light illumi- nates because the fuel-filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The light should turn off after a few driving trips. If the light does not turn off after a few driving trips, have the vehicle in- spected by a NISSAN dealer.

For additional information, see “Malfunction Indicator Light (MIL)” in the “2. Instruments and controls” section.

The LOOSE FUEL CAP warning will appear if the fuel-filler cap is not properly tightened. It may take a few driving trips for the message to be displayed. Failure to tighten the fuel-filler cap properly after the LOOSE FUEL CAP warning appears may cause the Malfunction Indicator Light (MIL) to illuminate.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (197,1)

to turn off the LOOSE FUEL CAP warning after tightening the fuel cap.

SPA2442

SPA2833

To remove the fuel-filler cap: 1. Turn the fuel-filler cap counterclockwise to

remove.

2. Put the fuel-filler cap on the cap holder *A

while refueling.

To install the fuel-filler cap: 1.

Insert the fuel-filler cap straight into the fuel- filler tube.

2. Turn the fuel-filler cap clockwise until a

single click is heard.

LOOSE FUEL CAP warning GUID-A04C09C8-3C53-423B-AC70-189E634F9E83
The LOOSE FUEL CAP warning appears on the dot matrix liquid crystal display when the fuel- tightened correctly after the filler cap is not vehicle has been refueled. It may take a few driving trips for the message to be displayed. To turn off the warning, perform the following steps: 1. Remove and install the fuel-filler cap as soon as possible. (See “Fuel-filler cap” earlier in this section.)

2. Tighten the fuel-filler cap until a single click

is heard.

3. Push the reset switch *A on the right side of the combination meter for about 1 second

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Pre-driving checks and adjustments 3-43

TILT/TELESCOPIC STEERING

GUID-24FBE4B2-4508-4AC7-A4F2-026DF692853E

WARNING

. Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an acci- dent.

. Do not adjust the steering wheel any closer to you than is necessary for proper steering operation and comfort. The driver’s air bag inflates with great force. If you are unrest- rained, leaning forward, sitting side- ways or out of position in any way, you are at greater risk of injury or death in a crash. You may also receive serious or fatal injuries from the air bag if you are up against it when it inflates. Always sit back against the seatback and as far away as practical from the steering wheel. Always use the seat belts.

Black plate (198,1)

SPA2443

SPA2444A

MANUAL OPERATION

GUID-20C3E099-AD1B-4DFF-97DD-6AF9D7373A42

forward or

GUID-69ADA9CB-3148-41B8-8BFC-2FD888E82F39
down and adjust the rearward to the

Manual operation Pull the lock lever *1
steering wheel desired position. Push the lock lever up securely to lock the steering wheel in place. Pull the lock lever *2
wheel up or down to the desired position. Release the lock lever to lock the steering wheel in place.

and adjust the steering

ELECTRIC OPERATION

GUID-27257F1D-DB84-47F2-83F2-B6F7CC1D700D

Tilt or telescopic operation GUID-0F8A0E36-72D5-4F58-A543-110128462B2D Move the lever to adjust the steering wheel up or down, rearward to the desired position.

forward or

Entry/Exit function operation (if so equipped): GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The automatic drive positioner system will make the steering wheel move up automatically when the driver’s door is opened with the ignition switch in the LOCK position. This lets the driver get into and out of the seat more easily. For more information, see “Automatic drive positioner” later in this section.

3-44 Pre-driving checks and adjustments

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (199,1)

SUN VISORS

GUID-E95255EA-C17D-4F05-8E11-DD566D7FB686

HARDTOP MODELS

GUID-ACCBC1FC-4BB4-4873-BB24-EFB9F2B19183

CAUTION

. Do not store the main sun visor before storing the extension sun visor.

. Do not pull the extension sun visor

forcedly downward.

1. To block out glare from the front, swing

down the main sun visor *1 .

2. To block glare from the side, remove the main sun visor from the center mount and swing it to the side *2 .

3. Draw out the extension sun visor *3

from the main sun visor to block from further glare.

SIC2872

CROSSCABRIOLET MODELS GUID-638F4A62-05CB-4943-BF6B-4E76A2BF9AB2
1. To block out glare from the front, swing

down the sun visor *1 .

2. To block glare from the side, remove the sun visor from the center mount and swing it to the side *2 .

Pre-driving checks and adjustments 3-45

SIC3451

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

MIRRORS

GUID-18188D7A-64F7-4D74-BFF2-8A606EDED136

SPA2447

INSIDE MIRROR GUID-333780B7-50C0-4562-BBC4-FEC53134867A Adjust the height and the angle of the inside mirror to the desired position.

Black plate (200,1)

SPA2143

SPA2422A

GUID-F100EFA2-76F3-450F-8CD1-FA039540B2A2

Manual anti-glare type The night position *1 will reduce glare from the headlights of vehicles behind you at night. Use the day position *2 when driving in daylight hours.

WARNING

Use the night position only when ne- cessary, because it reduces rear view clarity.

Type A

SPA2450

Type B

3-46 Pre-driving checks and adjustments

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (201,1)

For the HomeLink® Universal Transceiver opera- tion, see “HomeLink® Universal Transceiver” in the “2. Instruments and controls” section. OUTSIDE MIRRORS

GUID-EA0119F9-F39F-4DB3-A112-568766B0ECF6

WARNING

Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.

is designed so that

Automatic anti-glare type GUID-75561106-D8BE-4E21-A23B-64B84E0A7AC5
The inside mirror it automatically changes reflection according to the intensity of the headlights of the following vehicle. The anti-glare system will be automatically turned on when the ignition switch is pushed to the ON position. When the anti-glare system is turned on, the indicator light *A will illuminate and excessive glare from the headlights of the vehicle behind you will be reduced. switch *B to make the Type A: Push the inside rearview mirror operate normally and the indicator light will turn off. Push the switch again to turn the system on. Type B: Push the “*” switch *C to make the inside rearview mirror operate normally. The indicator light will turn off. Push the “I” switch *D to turn the system on. Do not allow any object to cover the sensors *E or apply glass cleaner on them. Doing so will reduce the sensitivity of the sensor, resulting in improper opera- tion. For the compass (if so equipped) operation, see “Compass” in the “2. Instruments and controls” section.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

SPA2319

Adjusting outside mirrors GUID-BDFF896E-E842-4BF3-8D64-FADE035BD4D5
The outside mirror control switch is located on the armrest. The outside mirror will operate only when the ignition switch is in the ACC or ON position. Turn the switch right or left to select the right or left side mirror *1 , then adjust using the control switch *2 .

Pre-driving checks and adjustments 3-47

Black plate (202,1)

Defrosting outside mirrors (if so equipped) GUID-68C28473-B796-47E1-911F-00D0EEF293DB The outside mirrors will be heated when the rear window defroster switch is operated.

SPA1829

SIC2064

Foldable outside mirrors GUID-820E720A-12E0-455E-87A1-9AB90C7B54F2
Fold the outside mirror by pushing it toward the rear of the vehicle.

VANITY MIRROR GUID-67A0AA3C-5897-4AD3-A960-33D20860995E To use the front vanity mirror, pull down the sun visor and pull up the cover.

3-48 Pre-driving checks and adjustments

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

AUTOMATIC DRIVE POSITIONER (if so equipped)

lever

GUID-851FDA9C-62A3-4F94-9BB3-456D0780664E The automatic drive positioner system has two features: . Entry/exit function (if equipped) . Memory storage ENTRY/EXIT FUNCTION (if equipped) GUID-B20D2394-0488-4194-B222-ACBB971CCC5C This system is designed so that the driver’s seat and steering column will automatically move when the selector is in the P (Park) position. This allows the driver to get into and out of the driver’s seat more easily. The driver’s seat will slide backward and the steering wheel will move up when the driver’s door is opened with the ignition switch in the LOCK position and the Intelligent Key not inserted in the Intelligent Key port. The driver’s seat and steering wheel will return to the previous positions when the ignition switch is pushed to the ACC position. The driver’s seat will not return to the previous positions if the seat or steering adjusting switch is operated when the seat is at the exit position.

Cancel or activate entry/exit function GUID-58D4463D-3833-4D6F-AB39-9C380DA99AC9
The selector lever must be in the P (Park) position with the ignition switch in the OFF position. The entry/exit function can be activated or canceled by pressing and holding the SET

switch for more than 10 seconds. The indicator lights on the memory switches (1
and 2) will blink once when the function is canceled, and the indicator lights will blink twice when the function is activated. Note that the indicator lights may illuminate after 5 seconds while holding the SET switch. This indicates readiness for linking the Intelligent Key to a stored memory position. Keep the SET switch pressed for more than 10 seconds to turn on or off the entry/exit function. The entry/exit function can also be activated or canceled if the “Lift Steering Wheel on Exit” key or “Slide Driver Seat Back on Exit” key is turned to ON or OFF in the “Comfort” settings. (See “Vehicle information and settings” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition systems” section.)

the entry/exit

Initialize entry/exit function GUID-3B7D11F0-51D7-4A5F-B078-9C3A3C24A746
If the battery cable is disconnected, or if the fuse opens, function will not work though this function was set on before. In such a case, after connecting the battery or replacing with a new fuse, open and close the driver’s door more than two times after the ignition switch is placed in the LOCK position from the ON position. The entry/exit function will be activated.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (203,1)

SPA2756

MEMORY STORAGE GUID-1645D943-6DDE-4A8E-B347-C359AF16FEDF Two positions for the driver’s seat, steering column and outside mirrors can be stored in the automatic drive positioner memory. Follow these procedures to use the memory system. 1. Move the selector lever

to the P (Park)

position.

2. Push the ignition switch to the ON position. 3. Adjust the driver’s seat, steering column and outside mirrors to the desired positions by manually operating each adjusting switch. For additional information, see “Seats” in the “1. Safety — Seats, seat belts and supple- mental restraint system” section and “Tilt/

Pre-driving checks and adjustments 3-49

Black plate (204,1)

. Push the ignition switch to the ON position and push the memory switch (1
or 2).

. Within 45 seconds of opening the driver’s door, push the memory switch (1 or 2).

The driver’s seat, steering column and outside mirrors will move to the memorized position with the indicator light flashing, and then the light will stay on for approximately 5
seconds.

SYSTEM OPERATION GUID-6E092FC2-4164-461D-8930-0184862E613A The automatic drive positioner system will not work or will stop operating under the following conditions: . When the vehicle speed is above 4 MPH (7

km/h) (entry/exit function).

. When the vehicle is driven (memory sto-

rage).

. When the adjusting switch for the driver’s seat and steering column is turned on while the automatic drive positioner is operating. . When the seat, steering column and outside mirrors have already been moved to the memorized position.

. When no position is stored in the memory

switch.

telescopic steering” earlier in this section and “Outside mirrors” earlier in this section. 4. Push the SET switch and, within 5 seconds,

then push the button on the Intelligent Key. The driver’s seat, steering wheel and outside mirrors will move to the memorized position.

push the memory switch (1 or 2). The indicator light for the pushed memory switch will stay on for approximately 5
seconds after pushing the switch. If memory is stored in the same memory switch, the previous memory will be deleted.

Linking Intelligent Key to a stored mem- ory position GUID-83DABFB4-1BAC-4D52-AAD9-89B23BBFA840
The Intelligent Key can be linked to a stored memory position with the following procedure. 1. Follow one of the steps for storing a memory

position.

. While the indicator light

for the memory switch being set is illuminated for 5 sec- onds, push the button on the Intelligent Key.

. Push the ignition switch to the OFF position,

and then push the SET switch. Push the button while pushing the memory button while the indicator light stays on for approxi- mately 5 seconds.

If the indicator light blinks, the Intelligent Key is linked to that memory setting. Push the ignition switch to the OFF position, and

3-50 Pre-driving checks and adjustments

If

Confirming memory storage GUID-C42E9A63-7C42-464C-ABAE-3B9C731E9AA0
. Push the ignition switch to the ON position and push the SET switch. the main memory has not been stored, the indicator light will come on for approximately 0.5
second. When the memory has stored in position, the indicator light will stay on for approximately 5 seconds. If the battery cable is disconnected, or if the fuse opens, the memory will be canceled. In this case, reset the desired position using the previous procedure. If optional keys are added to your vehicle, the memory storage procedure to switch 1
or 2 and linking Intelligent Key procedure to a stored memory position should be per- formed again for each Intelligent Key. For additional Intelligent Key information, see “Keys” earlier in this section.

Selecting the memorized position 1. Move the selector lever

GUID-1B13DD82-31E7-4920-83B1-6D7C94FBAB3E to the P (Park)

position.

2. Use one of the following methods to move the driver’s seat, the outside mirrors and the steering wheel.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]

Black plate (205,1)

. When the engine is started while moving the

automatic drive positioner.

. When the selector lever is moved from the P (Park) position to any other position. (How- ever, it will not be canceled while the seat and steering column are returning to the previous positions (entry/exit function).)

. When the driver’s door remains open for more than 45 seconds and the ignition switch is not in the ON position.

[ Edit: 2011/ 7/ 18 Model: Z51-D ]