2005 Nissan Murano Owners Manual

“Outside mirrors” earlier in this section.

3. Turn the ignition ON.

4. Push the SET switch and, within 5 seconds, push the memory switch (1 or 2) fully for at least 1 second.

The indicator light for the pushed memory switch will come on and stay on for approxi- mately 5 seconds after pushing the switch. After the indicator light goes off, the selected positions are stored in the selected memory (1 or 2).

If memory is stored in the same memory switch, the previous memory will be deleted. Linking a remote keyless entry to a stored memory position A remote keyless entry can be linked to a stored memory position with the following procedure. 1. Follow the steps for storing a memory posi-

tion.

for

light

2. While the indicator

the memory switch being set is illuminated for 5 seconds, push the unlock button on the remote keyless entry. The indicator light will blink. After the indicator light goes off, the remote keyless entry is linked to that memory setting.

3-34 Pre-driving checks and adjustments

With the key removed from the ignition switch, push the unlock button on the keyfob. The driver’s seat, pedals (Brake and Accelerator) and outside mirrors will move to the memorized position. Confirming memory storage 쐌 Turn the ignition switch to the ON position and push the SET switch. If the main memory has not been stored, the indicator light will come on for approximately 0.5 seconds. When the memory has stored the position, the indicator light will stay on for approxi- mately 5 seconds.

Selecting the memorized position 1. Set the sift selector lever to the P (Park)

position.

2. Turn the ignition ON. 3. Push the memory switch (1 or 2) fully for at

least 1 second. The driver’s seat, pedals (Brake and Accel- erator) and outside mirrors will move to the memorized position with the indicator light flashing, and then the light will stay on for approximately 5 seconds. SYSTEM OPERATION The automatic drive positioner system will not

work or will stop operating under the following conditions: 쐌 when the vehicle speed is above 4 MPH (7

km/h).

쐌 when any two or more of

the memory switches and the SET switch is simulta- neously pushed while the automatic drive positioner is operating.

쐌 when the adjusting switch for the driver’s seat, pedals and outside mirror are operated while the automatic drive positioner is oper- ating.

쐌 when the memory switch (1 or 2) and the least 1

SET switch is not pushed for at second.

쐌 when the seat has been already moved to the

memorized position.

쐌 when no seat position is stored in the

memory switch.

쐌 when the engine is started while moving the

automatic drive positioner.

쐌 when the shift selector lever is moved from the P position to any other position (However, it will not be cancelled if the switch is pushed while the seat is returning to the previous positions (entry/exit function).).

墌 05.4.8/Z50-D/V5.0 墍

MEMO

Pre-driving checks and adjustments 3-35

墌 05.4.8/Z50-D/V5.0 墍

MEMO

3-36 Pre-driving checks and adjustments

墌 05.4.8/Z50-D/V5.0 墍

4 Display screen, heater, air conditioner and

audio systems

Safety note .............................................................................. 4-2
Control panel buttons — without navigation system.... 4-2
How to use joystick and “ENTER” button................. 4-3
How to use “PREV” button ........................................... 4-3
How to use the “TRIP” button...................................... 4-3
How to use “FUEL ECON” BUTTON ........................ 4-4
Clock ................................................................................... 4-4
How to use “E/M” button .............................................. 4-4
How to use “MAINT” (Maintenance) button ............. 4-5
How to use “SETTING” button .................................... 4-6
“DAY/NIGHT” utton......................................................... 4-7
Control panel buttons — with navigation system.......... 4-8
How to use joystick and “ENTER” button................. 4-8
How to use “PREV” button ........................................... 4-8
Setting up the start-up screen ..................................... 4-9
How to use the “TRIP” button...................................... 4-9
Maintenance notice....................................................... 4-11
How to use the “SETTING” button .......................... 4-12
“DAY/NIGHT” button.................................................... 4-17
Rear view monitor (if so equipped) ................................ 4-17
How to read the displayed lines................................ 4-18
Rear view monitor setting............................................ 4-18

Operating tips................................................................. 4-18
Ventilators.............................................................................. 4-19
Heater and air conditioner (Automatic) ......................... 4-20
Automatic operation...................................................... 4-21
Manual operation ........................................................... 4-22
Operating tips................................................................. 4-22
In-cabin microfilter......................................................... 4-23
Servicing air conditioner.................................................... 4-23
Audio system ........................................................................ 4-24
FM radio reception........................................................ 4-24
AM radio reception ....................................................... 4-25
Satellite radio reception............................................... 4-25
Audio operation precautions....................................... 4-25
FM-AM-SAT radio with cassette player and/or compact disc (CD) player (TYPE A)/CD changer (TYPE B).......................................................................... 4-28
CD care and cleaning .................................................. 4-34
Steering switch for audio control (if so equipped).............................................................. 4-35
Antenna ............................................................................ 4-36
Car phone or CB radio .................................................... 4-36

墌 05.4.8/Z50-D/V5.0 墍

SAFETY NOTE

CONTROL PANEL BUTTONS — WITHOUT NAVIGATION SYSTEM

WARNING

쐌 Positioning of the heating or air con- ditioning controls and display con- trols should not be done while driv- ing, in order that full attention may be given to the driving operation.

쐌 Do not disassemble or modify this system. If you do, it may result in accidents, fire, or electrical shock.

쐌 Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in acci- dent, fire or electric shock.

쐌 In case you notice any foreign object in the system hardware, spill liquid on it, or notice smoke or smell com- ing from it, stop using the system immediately and contact a NISSAN dealer. Ignoring such conditions may lead to accidents, fire, or electrical shock.

4-2 Display screen, heater, air conditioner and audio systems

SAA0795A

墌 05.4.8/Z50-D/V5.0 墍

1. “TRIP” drive computer button; refer to page

4-3.

2. “FUEL ECON” button; refer to page 4-4.

3. Clock adjust button; refer to page 4-4.

4. “TRIP RESET” button; refer to page 4-3. 5. “E/M” button; refer to page 4-4. 6. “MAINT” maintenance button; refer to page

4-5.

it is instructed on the display. HOW TO USE “PREV” BUTTON Finish setup: If you push the “PREV” button after the setup is completed, the display will return to the previous screen.

7. “SETTING” button; refer to page 4-6. 8. JOYSTICK and “ENTER” button;

refer

to

page 4-3.

9. “PREV” previous button; refer to page 4-3. 10. “DAY/NIGHT” brightness control button;

refer to page 4-7.

Make sure the engine is running before using this system. Using the system with the engine off (igni- tion ON or ACC) for extended periods will drain the battery power, and the engine may not start. HOW TO USE JOYSTICK AND “ENTER” BUTTON Choose an item on the display using the joystick. Push the “ENTER” button only when the use of

SAA0796

HOW TO USE THE “TRIP” BUTTON When the “TRIP” button is pushed, the following modes will display on the screen. TRIP 1 (TIME, DIST, AVG) → TRIP 2 (TIME, DIST, AVG) → OFF You can set the two kinds of journey time (TIME — max 99 hours 59 minutes), trip odometer (DIST — mile or km) and average speed (AVG — MPH or km/h).

To reset the TRIP 1 or TRIP 2, push the “TRIP” button or the “TRIP RESET” button for more than approximately 1.5 seconds.

Display screen, heater, air conditioner and audio systems 4-3

墌 05.4.8/Z50-D/V5.0 墍

The display is updated every 30 seconds. At about the first 30 seconds and 1/3 miles (500
m) after a reset or connecting battery cable, the display will show (----). Distance to empty (DTE — mile or km) The distance to empty (DTE) mode provides you with an estimation of the distance that can be driven before refueling. The DTE is constantly being calculated, based on the amount of fuel in the fuel tank and the actual fuel consumption.

SAA0797

HOW TO USE “FUEL ECON” BUTTON The average fuel consumption (MPG or L/100
km) and the distance to empty (DTE — MI or km) will appear on the screen when the “FUEL ECON” button is pushed. Average fuel consumption (Mpg or L/100 km) The average fuel consumption mode shows the average fuel consumption since the last reset. Resetting is done by pushing the “TRIP RESET” or “FUEL ECON” button for more than approxi- mately 1.5 seconds. 4-4 Display screen, heater, air conditioner and audio systems

The display is updated every 30 seconds. When the fuel level is low, the DTE display will change to (*). NOTE: 쐌 The DTE reading may not change from the previous reading if the amount of fuel added is small.

쐌 Fuel moving in the tank while driving may cause the reading to momentarily change.

CLOCK The digital clock displays time when the ignition switch is in ACC or ON. If the battery cable is disconnected, the

clock will not indicate the correct time. Readjust the time. Adjusting the time To adjust the time, push the “H” or “M” button for more than approximately 1.5 seconds. The time indicator will flash. Push the H button to adjust the hour. Push the M button to adjust the minute. To finish the adjusting, push the “PREV” button or the screen will return to normal after 10
seconds. HOW TO USE “E/M” BUTTON You can change the unit as follows using the “E/M” (English/Metric) button. Unit: US — Mile, °F, MPG

Metric — km, °C, L/100 km

墌 05.4.8/Z50-D/V5.0 墍

(“ENGINE OIL” or “TIRE ROTATION”) when the vehicle is driven the set distance, turn ON the service alert key. To turn the service alert key ON, refer to “How to use the setting button” in this section. When the vehicle is driven the set distance, the MAINTENANCE screen will be automatically displayed and the Maintenance menu (“ENGINE OIL”, “TIRE ROTATION” and “TIRE PRES- SURE” (if so equipped)) will blink. To return to the previous display after the Main- tenance Notice message is displayed, push the PREV button. The “MAINTENANCE NOTICE” screen displays each time the key is turned ON until one of the following conditions are met: 쐌 “MAINT” button or “TRIP RESET” button is

pushed.

쐌 “Service alert key” is set OFF. 쐌 the maintenance interval is set again.

SAA0798

Tire pressure information (if so equipped) Pressure indication in ** psi on the screen indicates that the pressure is being measured. After a few driving trips, the pressure for each tire will be displayed randomly. The order of tire pressure figures displayed on the screen does not correspond with the actual order of the tire position. Tire pressure rises and falls depending on the heat caused by the vehicle’s traveling condition and the temperature. In case of low tire pressure, a message (FLAT Display screen, heater, air conditioner and audio systems 4-5

墌 05.4.8/Z50-D/V5.0 墍

SAA0646

HOW TO USE “MAINT” (Maintenance) BUTTON Pushing the “MAINT” button will change the maintenance menu as follows: ENGINE OIL → TIRE ROTATION → TIRE PRESSURE (if so equipped)

To reset the driving distance, push the “MAINT” button or “TRIP RESET” button for more than approximately 1.5 seconds.

Move the joystick to left or right distance.

to set

the

To automatically display the Maintenance menu

TIRE or CHECK ALL TIRE) is displayed on the screen: FLAT TIRE — low tire pressure.

WARNING

When a spare tire is mounted or a wheel is replaced, the pressure of that tire will not be indicated and not be monitored by the low tire pressure warning system. Contact a NISSAN dealer as soon as possible for tire replacement and/or system resetting.

HOW TO USE “SETTING” BUTTON Pushing the “SETTING” button will change the settings menu as follows: 쎻1 DISPLAY ON/OFF 쎻2 LANGUAGE 쎻3 BEEP SET 쎻4 SERVICE ALERT 쎻5 PERSONALIZED SETTINGS MENU

Display ON/OFF To turn off the screen, select the “OFF” key of the “Display ON/OFF” using the joystick. The screen will change to “CONFIRM DISPLAY OFF YES or NO”. If “YES” key is selected using the joystick, the screen will turn off after 2 beep sound and approximately 1 second. To turn on the screen, push the “SETTING”, trip control, air conditioner (except rear window de- froster button) or audio button. Language The language can be changed to “English” or “Franc¸ ais” using the joystick. Beep set If the beep set “OFF” key is selected using the joystick, the beep sound will not operate. (except some caution beep sounds) Service alert If the service alert “ON” key is selected, the information will be displayed when the engine oil and the tire rotation reaches the preset driving distance.

Personalized setting menu You can set the electronic systems as follows using the joystick. Slide back DR seat on exit: The driver’s seat automatically moves back and returns to the original position for ease of exit and entry. Remote unlock door logic: This key can switch the unlock doors of the 1st unlocking operation as follows: Only the driver side door ←→ All the doors Horn chirp with remote*: This key changes the horn chirp mode that occurs when pushing the LOCK button on the keyfob. Lights flash with remote*: flash This key changes the hazard indicator mode that occurs when pushing the LOCK or UNLOCK button on the keyfob. * Even if you change the horn chirp or the hazard flash with the keyfob, the change may not be reflected in the display. Use the keyfob to return to the previous mode.

4-6 Display screen, heater, air conditioner and audio systems

墌 05.4.8/Z50-D/V5.0 墍

SONALIZED SETTINGS will return to the initial conditions. Return all settings to default: When this key is selected and turned on using the joystick, all settings made by personalized setting menu will return to the initial conditions. “DAY/NIGHT” BUTTON To change the display brightness, push the “DAY/NIGHT” button. Pushing the button again will change the display to DAY or NIGHT dis- play. Then, adjust the brightness moving the joystick right or left. If no operation is done within 10 seconds, or if the “PREV” button is pushed, the display will return to the previous display. Pushing the “DAY/NIGHT” button for more than approximately 1.5 seconds will turn the display off. The screen will change to “CONFIRM DIS- PLAY OFF YES or NO”.

Auto re-lock time:

The length of the auto door re-lock time can be set. Select the “Auto Re-Lock time” key, then move the joystick to adjust the time. Auto headlights sensitivity:

Automatic light illumination can be set as de- sired.

Select the “Sensitivity of Automatic Headlights” key, then move the joystick to the left (lower) or right (higher). Auto headlights off delay:

You can control how long it takes the automatic turn off timer to extinguish the headlights in the AUTO position. Select the “Automatic Headlights Off Delay” key, then move the joystick to the left or right to adjust the timer. Speed sensing wiper interval: This key turns on and off the driving speed dependent intermittent wiper function. Confirm reset settings: To display the “Confirm Reset Settings”, select “YES”. When this key is selected and turned on using the “ENTER” button, all settings made by PER-

Display screen, heater, air conditioner and audio systems 4-7

墌 05.4.8/Z50-D/V5.0 墍

CONTROL PANEL BUTTONS — WITH NAVIGATION SYSTEM

4-8 Display screen, heater, air conditioner and audio systems

SAA0648A

1. “TRIP” drive computer button; refer to page

4-9.

2. “SETTING” button; refer to page 4-12.

3. Joystick and “ENTER” push button; refer to

page 4-8.

4. “PREV” previous button; refer to page 4-8.

5. “DAY/NIGHT” brightness control button; re-

fer to page 4-17.

6 - 10. For Navigation system control buttons 쎻A ; refer to the separate Navigation Owner’s Manual.

When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start. HOW TO USE JOYSTICK AND “ENTER” BUTTON Choose an item on the display using the joystick and push the “ENTER” button for operation. HOW TO USE “PREV” BUTTON This has two functions. 쐌 Go back to the previous display (cancel).

墌 05.4.8/Z50-D/V5.0 墍

If you touch “PREV” button during setup, the setup will be canceled and/or the display will return to the previous screen. 쐌 Finish setup. If you touch this button after the setup is com- pleted, the setup will start over, and the display will return to the climate control or Audio mode, and Navigation screen. SETTING UP THE START-UP SCREEN When you turn the ignition switch to ACC, the SYSTEM START-UP warning is displayed on the screen. Read the warning and select the “I AGREE” (English) or “ENTER” (Franc¸ ais) key then push the “ENTER” button. If you do not push the “ENTER” button, this system will not proceed to the next step display. If you do not touch the button or screen key for more than 1 minute on the TRIP, SETTING or START-UP screen, the screen will change to TRIP screen automatically. To proceed to the next step, refer to the separate Navigation system Owner’s Manual. HOW TO USE THE “TRIP” BUTTON When the “TRIP” button is pushed, the following models will display on the screen.

Warning message (if there are any) → TRIP 1
(Elapsed Time, Driving Distance, Average Speed) → TRIP 2 → FUEL ECONOMY (Aver- age Fuel Economy, Distance to Empty) → MAINTENANCE (Engine Oil, Tire Rotation and Tire Pressure — if so equipped).

SAA0654

Trip 1, trip 2 and fuel economy items To reset the TRIP 1, TRIP 2 and FUEL ECONOMY, select the “RESET” key using the joystick and push the “ENTER” button or push the “TRIP” button for more than approximately 1.5 seconds.

Display screen, heater, air conditioner and audio systems 4-9

墌 05.4.8/Z50-D/V5.0 墍

SAA0695

SAA0655

SAA0656

Maintenance items You can set the engine oil and the tire rotation interval. And the tire pressure will appear on the screen (if the tire pressure system is equipped). To display the setting of the maintenance inter- val, select the “Engine Oil” or “Tire Rotation” key using the joystick and push the “ENTER” button.

the maintenance interval, select

the To set “Maintenance Schedule” key by using the joy- stick and push the joystick to right or left. To reset the maintenance interval, select the “RESET” key using the joystick and push the “ENTER” button. To display the MAINTENANCE NOTICE, auto- matically when setting trip distance is reached, select the “Display Maintenance Notification” key and push the “ENTER” button.

4-10 Display screen, heater, air conditioner and audio systems

墌 05.4.8/Z50-D/V5.0 墍

The “MAINTENANCE NOTICE” screen displays each time the key is turned ON until one of the following conditions are met: 쐌 “RESET” is selected. 쐌 “Display Maintenance Notification” is set

OFF.

쐌 the maintenance interval is set again.

SAA0858B

MAINTENANCE NOTICE The “MAINTENANCE NOTICE” screen (“EN- GINE OIL” or “TIRE ROTATION”) will be auto- matically displayed as shown when both of the following conditions are met: 쐌 the vehicle is driven the set distance and the

ignition switch is turned OFF.

쐌 the ignition key is turned ON the next time the

vehicle will be driven.

To return to the previous display after the “MAINTENANCE NOTICE” screen is displayed, push the PREV button.

SAA0657

Tire pressure information (if so equipped) To view “TIRE PRESSURE” information, push the “TRIP” button repeatedly until the “MAINTE- NANCE” screen is displayed. Select “TIRE PRESSURE” using the joystick and push the “ENTER” button.

Pressure indication in ** psi on the screen indicates that the pressure is being measured. After a few driving trips, the pressure for each tire will be displayed randomly.

The order of tire pressure figures displayed on the screen does not correspond with the actual Display screen, heater, air conditioner and audio systems 4-11

墌 05.4.8/Z50-D/V5.0 墍

order of the tire position. Tire pressure rises and falls depending on the heat caused by the vehicle’s traveling condition and the temperature. In case of displayed on the screen: FLAT TIRE — low tire air pressure.

low tire pressure, a message is

WARNING

When a spare tire is mounted or a wheel is replaced, the pressure of that tire will not be indicated and not be monitored by the low tire pressure warning system. Contact a NISSAN dealer as soon as possible for tire replacement and/or system resetting.

SAA0649A

SAA0652

* — Refer to the separate Navigation system Owner’s Manual. HOW TO USE THE “SETTING” BUTTON The SETTINGS screen will appear when the “SETTING” button is pushed.

“Display” settings The DISPLAY SETTINGS screen will appear when selecting the “Display” key and pushing the “ENTER” button. Brightness/Contrast/Map Background:

To adjust the brightness and contrast of the screen, select the “Brightness/Contrast/Map Background” key and push the “ENTER” button. Then you can adjust the brightness to Darker or Brighter, the contrast to Lower or Higher using the joystick.

The Map Background is related to the navigation

4-12 Display screen, heater, air conditioner and audio systems

墌 05.4.8/Z50-D/V5.0 墍

system. Refer to the separate navigation system Owner’s Manual. Display Off: To turn off the screen, push the “SETTING” button and select the “Display” key and “Display Off” key. The indicator of the “Display Off” will turn on in amber. When any mode button is pushed with the screen off, the screen turns on for further operation. The screen will turn off automatically 5 seconds after the operation is finished on the map display in the Audio, HVAC (Heater and air conditioner). To turn on the screen, push the “SETTING” button and select the “Display” key and “Display Off” key, then set the screen to on by pushing the “ENTER” button. Setting Audio or HVAC display: Choose the “Audio” or “HVAC” (Heater and air conditioner) key to be displayed at the bottom, by using the joystick. The audio or HVAC (heater, air conditioner) setting condition will normally appear on the screen. To return to the setting screen, push the “SETTING” button or “PREV” button.

SAA1029

SAA0794

Vehicle electronic systems The VEHICLE ELECTRONIC SYSTEMS screen will appear when selecting the “Vehicle Elec- tronic Systems” key with the joystick and push- ing the “ENTER” button. You can set operating conditions. To set an operating condition, select the appli- cable item using the joystick, and push the “ENTER” button. The indicator light alternately turns on and off each time the “ENTER” button is pushed. Indicator light is illuminated. — ON

the various electronic systems

Indicator light is not illuminated. — OFF Adjust driver seat when exiting vehicle (if so equipped):

The driver’s seat automatically moves back and returns to the original position for ease of exit and entry. Remote unlock driver’s door first (Selective door unlock):

This key can switch the unlock doors of the 1st unlocking operation as follows: ON (Only the driver side door) ←→ OFF (All the doors)

Display screen, heater, air conditioner and audio systems 4-13

墌 05.4.8/Z50-D/V5.0 墍

Intelligent Key lock response — Sound (if so equipped): The sound pattern of the Intelligent request switch operation can be set as desired. Select the “Intelligent Key lock response — Sound” key, then push the ENTER button to change the sound pattern. Intelligent Key unlock response — Sound (if so equipped): The beep sounds when unlocking door with the Intelligent request switch can be turned on or off. Return all settings to default: When this key is selected and turned on using the “ENTER” button, all settings made by VEHICLE ELECTRONICS will return to the initial conditions.

the Intelligent Key to return to the previ- ous mode.

Auto re-lock time: The length of the auto door re-lock time can be set. Select the “Auto Re-Lock time” key, then move the joystick and push the ENTER button to adjust the time. Sensitivity of automatic headlights: Automatic light illumination can be set as de- sired. Select the “Sensitivity of Automatic Headlights” key, then move the joystick to the left (lower) or right (higher). Automatic headlights off delay: You can control how long it takes the automatic turn off timer to extinguish the headlights in the AUTO position. Select the “Automatic Headlights Off Delay” key, then move the joystick to the left or right to adjust the timer. Speed dependent wiper: This key turns on and off the driving speed dependent intermittent wiper function.

SAA1030

Keyless remote response — Horn*:

This key changes the horn chirp mode that occurs when pushing the LOCK button on the keyfob or the Intelligent Key. Keyless remote response — Lights*:

This key changes the hazard indicator flash mode that occurs when pushing the LOCK or UNLOCK button on the keyfob or the Intelligent Key. * Even if you change the horn chirp or the hazard flash with the keyfob or the Intel- ligent Key, the change may not be re- flected in the display. Use the keyfob or

4-14 Display screen, heater, air conditioner and audio systems

墌 05.4.8/Z50-D/V5.0 墍

SAA0658

SAA0659

SAA0660

System settings Language/Unit: The LANGUAGE/UNIT screen will appear when selecting the “Language/Unit” key and pushing the “ENTER” button. Language: English or French Unit: US — Mile, °F, MPG

Metric — km, °C, L/100 km

You can select the language and unit using the joystick and “ENTER” button.

Clock: Adjusting the time Select the “Hours” or “Minutes” key and tilt the joystick to the right or left to adjust the time. The time will change step by step. After completion of the setting, push the “PRE- VIOUS” button.

Setting daylight saving time Turn ON or OFF daylight saving time. Every time the “Daylight Saving Time” key is selected, the light turns ON and OFF alternately. ON: The displayed time advances by one hour. OFF: The current time is displayed.

Display screen, heater, air conditioner and audio systems 4-15

墌 05.4.8/Z50-D/V5.0 墍

SAA0661

SAA0662

SAA0663

Adjusting the time to the GPS Select the “Auto Adjust” key. The time will be reset to the GPS time.

Selecting the time zone 1. Select the “Select Time Zone” key. The TIME ZONE screen will appear.

4-16 Display screen, heater, air conditioner and audio systems

2. Select one of the following zones depending

on the current location.

쐌 “Pacific” zone 쐌 “Mountain” zone 쐌 “Central” zone 쐌 “Eastern” zone 쐌 “Atlantic” zone 쐌 “Newfoundland” zone After selection, the CLOCK SETTINGS screen will appear. The GPS time (manual time) corresponding to

墌 05.4.8/Z50-D/V5.0 墍

the selected zone will be displayed. “Pacific” zone has been set as the initial (default) setting. Beep setting: When Beep setting is on (indicator light on), a beep will sound if any audio button is pushed. “DAY/NIGHT” BUTTON To change the display brightness, push the “DAY/NIGHT” button. Pushing the button again will change the display to DAY or NIGHT dis- play. Then, adjust the brightness moving the joystick right or left. If no operation is done within 10 seconds, or if the “PREV” button is pushed, the display will return to the previous display.

REAR VIEW MONITOR (if so equipped) When the shift lever is shifted into the R (Re- verse) position, the monitor display shows view to the rear of the vehicle.

The system is designed as an aid to the driver in detecting large stationary objects to help avoid damaging the vehicle. The system will not detect small objects below the bumper and may not detect objects close to the bumper or on the ground.

WARNING

쐌 The rear view camera is a conve- nience but it is not a substitute for proper backing. Always turn and check that it is safe to do so before backing up. Always back up slowly. 쐌 Objects viewed in the rear view moni- tor differ from actual distance be- cause a wide-angle lens is used. Ob- jects in the rear view monitor will appear visually opposite like ones viewed in the inside and outside mir- rors.

쐌 Make sure that the back door is se-

curely closed when backing up.

쐌 Underneath the bumper and the cor- ner areas of the bumper cannot be viewed on the rear view monitor be- cause of its monitoring range limita- tion.

쐌 Do not put anything on the rear view camera. The rear view camera is in- stalled above the license plate.

쐌 When washing the vehicle with high- pressure water, be sure not to spray it around the camera. Otherwise, wa- ter may enter the camera unit caus- ing water condensation on the lens, a malfunction, fire or an electric shock. 쐌 Do not strike the camera. It is a pre- cision instrument. Otherwise, it may malfunction or cause damage result- ing in a fire or an electric shock.

CAUTION

There is a plastic cover over the camera. Do not scratch the cover when cleaning dirt or snow from it.

Display screen, heater, air conditioner and audio systems 4-17

墌 05.4.8/Z50-D/V5.0 墍

REAR VIEW MONITOR SETTING

WARNING

Do not adjust the Brightness, Contrast, Tint and Color of the rear view monitor while the vehicle is moving. Make sure the parking brake is firmly applied and the engine is not running.

To adjust the Brightness, Contrast, Tint and Color of the rear view monitor, push the “SET- TING” button with the rear view monitor on, select the item key and adjust the level using the joystick. OPERATING TIPS 쐌 When the shift

the monitor screen automatically changes to the rear view monitor mode. However, the radio can be heard.

lever is shifted to R,

쐌 It may take some time until the rear view monitor is displayed after the shift lever has been shifted to R. Objects may be distorted momentarily until the rear view monitor screen is displayed completely. When the shift lever is returned to a position other than R, it may take some time until the screen

changes. Objects on the screen may be distorted until they are completely displayed. 쐌 When the temperature is extremely high or low, the screen may not clearly display ob- jects. This is not a malfunction.

쐌 When strong light directly enters the camera,

objects may not be displayed clearly.

쐌 Vertical lines may be seen in objects on the screen. This is due to strong reflected light from the bumper. This is not a malfunction.

쐌 The screen may flicker under light. This is not a malfunction.

fluorescent

쐌 The colors of objects on the rear view monitor may differ somewhat from those of the actual object.

쐌 When the contrast of objects is low at night, pushing the “ENTER” button may not change the brightness.

쐌 Objects on the monitor may not be clear in a

dark place or at night.

쐌 If dirt, rain or snow attaches to the camera, the rear view monitor may not clearly display objects. Clean the camera.

쐌 Do not use alcohol, benzine or thinner to clean the camera. This will cause discolora- tion. To clean the camera, wipe with a cloth

SAA0889

HOW TO READ THE DISPLAYED LINES Lines which indicate the vehicle clearance and distances to objects with reference to the bumper line 쎻A are displayed on the monitor. They are indicated as reference distances to objects. Displayed lines indicate distances 1.5
feet (red) 쎻1 , 3 feet (yellow) 쎻2 , 7 feet (green) 쎻3 and 10 feet (green) 쎻4 from the lower part of the bumper line 쎻A . The vehicle clearance lines are wider than the actual clearance.

4-18 Display screen, heater, air conditioner and audio systems

墌 05.4.8/Z50-D/V5.0 墍

VENTILATORS

dampened with diluted mild cleaning agent and then wipe with a dry cloth.

쐌 Do not damage the camera as the monitor

screen may be adversely affected.

쐌 Do not use body wax on the camera window. Wipe off any wax with a clean cloth damp- ened with mild detergent diluted with water.

SAA0640

Open or close, and adjust the air flow direction of ventilators. 쎻A :This symbol

the vents are closed when the vent switch is moved to the left.

indicates that

쎻B :This symbol indicates that the vents are open when the vent switch is moved to the right.

Display screen, heater, air conditioner and audio systems 4-19

墌 05.4.8/Z50-D/V5.0 墍

HEATER AND AIR CONDITIONER (Automatic)

8. Temperature control knob (driver only, or

driver and passenger)

9. “OFF” button for climate control system 10. Fan speed control knob 11. “DUAL” passenger side temperature con-

trol ON/OFF button

12. Temperature control knob (passenger side)

1. “AUTO” climate control ON button 2. “

” fresh air button

3. “

4. “

” air recirculation button

” front defroster button

SAA0641

5. “

” rear window defroster switch; refer to the “2. Instrument and controls” section.

6. “A/C” air conditioner ON/OFF button 7. “MODE” manual air flow control button

4-20 Display screen, heater, air conditioner and audio systems

墌 05.4.8/Z50-D/V5.0 墍

WARNING

쐌 The air conditioner cooling function operates only when the engine is running.

쐌 On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or animals. Do not leave children or adults who would normally require the assistance of others in your ve- hicle. Unattended pets should also not be left alone.

쐌 Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

쐌 Positioning of the heater and/or air conditioner controls should not be done while driving so that full atten- tion may be given to vehicle operation.

Start the engine and operate the controls to

activate the air conditioner. AUTOMATIC OPERATION Cooling and/or dehumidified heating (AUTO) This mode may be normally used all year round as the system automatically works to keep a constant temperature. Air flow distribution and fan speed are also controlled automatically. 1. Push the AUTO button on. (AUTO will be

displayed.)

2. Turn the temperature set dial to the left or

right to set the desired temperature.

쐌 Adjust the temperature set dial to about 75°F

(24°C) for normal operation.

쐌 The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution and fan speed are also con- trolled automatically.

3. You can individually set driver and front pas- senger side temperature using each tem- perature control knob. When the DUAL but- ton is pushed or passenger side temperature control knob is turned, the DUAL indicator will come on. To turn off the passenger side temperature control, push the DUAL button.

Heating (A/C OFF) The air conditioner does not activate. When you need to heat only, use this mode.

1. Push the A/C button.

(A/C OFF will be

displayed and A/C indicator will turn off.)

2. Turn the temperature set dial to the left or

right to set the desired temperature.

쐌 The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution and fan speed are also con- trolled automatically.

쐌 Do not set the temperature lower than the outside air temperature. Otherwise the sys- tem may not work properly.

쐌 Not recommended if windows fog up. Dehumidified defrosting or defogging FRONT defroster button on. 1. Push the (The indicator light on the button will come on.)

2. Turn the temperature set dial to the left or

right to set the desired temperature.

쐌 To quickly remove ice from the outside of the windows, turn the fan speed control knob to right and set to the maximum position.

쐌 As soon as possible after the windshield is Display screen, heater, air conditioner and audio systems 4-21

墌 05.4.8/Z50-D/V5.0 墍

clean, push the AUTO button to return to the auto mode. 쐌 When the

front defroster button is pushed, the air conditioner will automatically be turned on at outside temperatures above 23°F (−5°C) to defog the windshield, and the air recirculate mode will automatically be turned off. Outside air is drawn into the passenger compartment to improve the defogging per- formance.

to manually

MANUAL OPERATION Fan speed control Turn the fan control button control the fan speed. Push the AUTO button to return to automatic control of the fan speed. Air recirculation Push the air recirculation button to recir- culate interior air inside the vehicle. The indicator light on the cannot be activated The air recirculation when the air conditioner is in the front defrosting mode

button will come on.

To turn the system off Push the OFF button. OPERATING TIPS When the engine coolant temperature and out- side air temperature are low, the air flow from the foot outlets may not operate for a maximum of 150 seconds. However, this is not a malfunction. After the coolant temperature warms up, the air flow from the foot outlets will operate normally.

Fresh air Push the button to draw outside air into the passenger compartment. The indicator light on the button will come on. Automatic intake air control In the AUTO mode, the intake air will be con- the trolled automatically. To manually control intake air, push the air recirculate or fresh air button. To return to the automatic control mode, push the indicator-illuminated but- ton for about 2 seconds. The indicator lights (both air recirculate and fresh air buttons) will flash twice, and then the intake air will be controlled automatically. Air flow control Pushing the MODE manual air button selects the air outlet to:

flow control

: Air flows from center and side ventila-

tors.

: Air flows from center and side ventila-

tors and foot outlets.

: Air flows from foot outlets and side

ventilators.

: Air flows from defroster,

and side ventilators.

foot outlets

4-22 Display screen, heater, air conditioner and audio systems

墌 05.4.8/Z50-D/V5.0 墍

decreases significantly or if windows fog up easily when operating the heater or air conditioning system.

SERVICING AIR CONDITIONER

The air conditioning system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. This refrigerant will not harm the earth’s ozone layer. How- ever, special charging equipment and lubricants are required when servicing your NISSAN air conditioner. Using improper refrigerants or lubri- cants will cause severe damage to your air conditioning system. See “Capacities and rec- ommended fuel/lubricants” in the “9. Technical and consumer information” section for air con- ditioning system refrigerant and lubricant recom- mendations.

A NISSAN dealer will be able to service your environmentally friendly air conditioning system.

WARNING

The air conditioner system contains re- frigerant under high pressure. To avoid personal injury, any air conditioner ser- vice should be done only by an experi- enced technician with proper equip- ment.

Display screen, heater, air conditioner and audio systems 4-23

墌 05.4.8/Z50-D/V5.0 墍

SAA0642

The sensor on the instrument panel helps main- tain a constant temperature; do not put anything on or around this sensor. IN-CABIN MICROFILTER The air conditioning system is equipped with an in-cabin microfilter which collects dirt, pollen, dust, etc. To make sure the air conditioner heats, defogs, and ventilates efficiently, replace the filter according to the specified maintenance intervals listed in your Service and Maintenance Guide. To replace the filter, contact a NISSAN dealer. The filter should be replaced if the air flow

change. Buildings, terrain, signal distance and interference from other vehicles can work against ideal reception. Described below are some of the factors that can affect your radio reception.

AUDIO SYSTEM

Turn the ignition switch to ACC or ON and push the power on switch to turn on the radio. If you listen to the radio with the engine not running, the key should be turned to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external in- fluences. Intermittent changes in reception qual- ity normally are caused by these external influences. Using a cellular phone in or near the ve- hicle may influence radio reception quality. Radio reception Your radio system is equipped with state-of-the- art electronic circuits to enhance radio recep- tion. These circuits are designed to extend re- ception range, and to enhance the quality of that reception. However there are some general characteristics of FM, AM and satellite radio signals that can affect radio reception quality in a moving vehicle, even when the finest equipment is used. These characteristics are completely normal in a given reception area, and do not indicate any malfunc- tion in your radio system. Remember that a moving vehicle is not the ideal place to listen to a radio. Because of the move- ment, reception conditions will constantly 4-24 Display screen, heater, air conditioner and audio systems

SAA0306

FM RADIO RECEPTION Range: FM range is normally limited to 25 to 30
miles (40 to 48 km), with monaural (single channel) FM having slightly more range than stereo FM. External influences may sometimes interfere with FM station reception even if the FM station is within 25 miles (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line-of-sight path, exhibiting many of the same characteristics as light. For example they will reflect off objects.

Fade and drift: As your vehicle moves away from

墌 05.4.8/Z50-D/V5.0 墍

a station transmitter, the signals will tend to fade and/or drift.

Static and flutter: During signal interference from buildings, large hills or due to antenna position, usually in conjunction with increased distance from the station transmitter, static or flutter can be heard. This can be reduced by adjusting the treble control counterclockwise to reduce treble response. Multipath reception: Because of the reflective characteristics of FM signals, direct and re- flected signals reach the receiver at the same time. The signals may cancel each other, result- ing in momentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics, AM signals are also sub- ject to interference as they travel from transmitter to receiver. Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist. Static: Caused by thunderstorms, electrical

power lines, electric signs and even traffic lights. SATELLITE RADIO RECEPTION When the satellite radio is first installed or the battery has been replaced, the satellite radio may not work properly. This is not a malfunction. Wait more than 10 minutes with satellite radio ON for satellite radio to receive all of the neces- sary data.

No satellite radio reception is available and “NO SAT” will be displayed when the SAT button is pushed unless the optional satellite receiver and antenna were factory installed (late availability only/retrofit unavailable), and an XM or SIRI- USTM satellite radio service subscription is ac- tive.

Satellite radio performance may be effected if cargo carried on the roof rack blocks the satellite radio signal.

If possible, do not put cargo over the satellite radio antenna. AUDIO OPERATION PRECAUTIONS Cassette player 쐌 To maintain good quality

sound, NISSAN recommends using cassette tapes of 60 minutes or shorter in length.

쐌 Cassette tapes should be removed from the player when not in use. Store cas- settes in their protective cases and away from direct sunlight, heat, dust, moisture and magnetic sources.

쐌 Direct sunlight can cause the cassette to become deformed. The use of deformed cassettes may cause the cassette to jam in the player.

쐌 Do not use cassettes with labels which are peeling and loose. If used, the label could jam in the player.

쐌 If a cassette has loose tape, insert a pencil through one of the cassette hubs and rewind the tape firmly around the hubs. Loose tape may cause tape jam- ming and wavering sound quality.

쐌 Over a period of time, the playback head, capstan and pinch roller may col- lect a tape coating residue as the tape is played. This residue accumulation can cause weak or wavering sound, and should be removed periodically with a head cleaning tape. If the residue is not removed periodically, the player may need to be disassembled for cleaning.

Display screen, heater, air conditioner and audio systems 4-25

墌 05.4.8/Z50-D/V5.0 墍

• CDs with a paper label • CDs that are warped, scratched, or

have abnormal edges

쐌 During cold weather or rainy days, the player may malfunction due to the hu- midity. If this occurs, remove the CD and dehumidify or ventilate the player com- pletely.

쐌 The player may skip while driving on

rough roads.

쐌 The CD player sometimes cannot func- tion when the compartment tempera- ture is extremely high. Decrease the temperature before use.

쐌 Do not expose the CD to direct sunlight. 쐌 CDs that are of poor quality, dirty, scratched, covered with fingerprints, or that have pin holes may not work prop- erly.

쐌 The following CDs may not work prop-

erly: • Copy control compact discs (CCCD) • Recordable compact discs (CD-R) • Rewritable compact discs (CD-RW)

쐌 Do not use the following CDs as they may cause the CD player to malfunction. • 3.1 in (8 cm) discs with an adapter • CDs that are not round

SAA0480

Compact Disc (CD) player 쐌 Only use high quality 4.7 inches (12 cm) round discs that have the “COMPACT disc DIGITAL AUDIO” logo on the disc or packaging.

4-26 Display screen, heater, air conditioner and audio systems

墌 05.4.8/Z50-D/V5.0 墍

1. SEEK/APS REW, APS FF/TRACK

CHANGE button

2. CD slot 3. Station

and

(FM/AM/SAT)/CD insert/eject or CD play (Type B only) select button

preset

4. A.B.C. preset select button 5. CD EJECT button 6. RADIO TUNE/FF⋅REW button 7. ON⋅OFF/VOLUME control knob 8. “PAUSE/MUTE” button 9. “FM” band select button (Type A) 10. “AM” band select button (Type A) 11. CD play button 12. “SAT” satellite radio select button 13. Tuning up/down knob and AUDIO (BASS, TREBLE, FADE, and BALANCE, (SSV and NR (Dolby) — Type B only)) knob

14. PROG (program)/RPT (repeat) play button 15. FM-AM band select button (Type B) 16. TAPE play button (Type B) 17. TAPE EJECT button (Type B) 18. CD LOAD button (Type B only)

SAA0650

SAA0651

Display screen, heater, air conditioner and audio systems 4-27

墌 05.4.8/Z50-D/V5.0 墍

system is on, pushing the ON⋅OFF/Volume con- trol knob turns the system off.

FM-AM-SAT RADIO WITH CASSETTE PLAYER AND/OR COMPACT DISC (CD) PLAYER (TYPE A)/CD CHANGER (TYPE B) No satellite radio reception is available and “NO SAT” will be displayed when the SAT button is pushed unless the optional satellite receiver and antenna were factory installed (late availability only/retrofit unavailable), and an XM or SIRI- USTM satellite radio service subscription is ac- tive. Audio main operation The tape deck (type B) employs a permalloy head which allows for improved reproduction of high frequency ranges. Noise is also greatly reduced by the combined use of the Dolby NR (Noise Reduction) system. The auto loudness circuit enhances the low frequency range auto- matically in both radio reception and tape and CD playback. ON⋅OFF/Volume control: Turn the ignition switch to ACC or ON, and then push the ON⋅OFF/Volume control knob while the system is off to call up the mode (radio, tape or CD) which was playing immediately before the system was turned off. When no CD or tape is loaded, the radio will come on. While the 4-28 Display screen, heater, air conditioner and audio systems

To turn the radio off, push the Power/Volume control knob. Turn the ON⋅OFF/Volume control knob to adjust the volume. This vehicle has Speed Sensitive control Vol- ume (SSV) for audio (type B only). The audio volume changes as the driving speed changes. AUDIO knob (BASS, TREBLE, FADE, BALANCE, (SSV and NR (Dolby) — type B only)): Push the AUDIO knob to change the selecting mode as follows. BASS → TREBLE → FADE → BALANCE → SSV (type B only) → NR (when cassette playing type B only) To adjust BASS, Treble, Fader and Balance, push the AUDIO knob until the desired mode BASS, TREBLE, FADE or BALANCE appears in the display. Turn the Tuning knob to adjust Bass and Treble to the desired level. Use the Tuning knob also to adjust Fader or Balance modes. Fader adjusts the sound level between the front and rear speakers and Balance adjusts the sound between the right and left speakers. To change the SSV mode to OFF, LOW, MID or

HIGH, turn the Tuning knob to right or left. (type B only).

To change the NR (Dolby) mode to OFF or ON, turn the Tuning knob to right or left while cas- sette tape is playing. When Dolby is ON, the display indicates the

mark. (type B only)

Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Cor- poration. Dolby NR and the double-D symbol ” are trademarks of Dolby Laboratories “ Licensing Corporation.

After 10 seconds, the radio, cassette tape or CD display reappears. Once the sound quality is set to the desired level, push the AUDIO button repeatedly until the radio, cassette tape or CD display appears. Display CD text:

To indicate the CD mode text, push the AUDIO knob during CD playing. Track No. → Track title → Disc title → BASS → TREBLE → FADE → BALANCE → SSV → Display mode

To change the indicated text in display mode, turn the tuning knob within 2 seconds.

The text will change as follows:

墌 05.4.8/Z50-D/V5.0 墍

only/retrofit unavailable), and an XM or SIRI- USTM satellite radio service subscription is ac- tive.

Pushing the FM/AM (Type B), FM, AM (Type A) or SAT band select button will change the band as follows: AM ↔ FM or SAT (Satellite) When FM/AM/SAT radio select button is pushed while the ignition switch is in the ACC or ON, the radio will come on at the station last played. The last station played will also come on when the power knob is turned to ON. If a compact disc or tape is playing when the FM/AM/SAT radio select button is turned to ON, the compact disc or tape will automatically be turned off and the last radio station played will come on. The FM stereo indicator ST will glow during FM stereo reception. When the stereo broadcast signal the radio will automatically change from stereo to monaural reception.

is weak,

Display satellite radio text:

To indicate the satellite mode text, push the AUDIO knob during satellite radio play. Artist → Title → BASS → TREBLE → FADE → BALANCE → SSV → Display mode To change the indicated text in display mode, turn the tuning knob within 2 seconds.

Pause/mute button:

To mute or pause the audio sound, push the PAUSE/MUTE button. To release the mute or pause, push the button again. FM-AM-SAT radio operation

or SAT FM/AM/SAT radio

select:

No satellite radio reception is available and “NO SAT” will be displayed when the SAT button is pushed unless the optional satellite receiver and antenna were factory installed (late availability

TUNE (Tuning):

WARNING

The radio should not be tuned while driving so full attention may be given to vehicle operation.

or

To tune the radio, push the RADIO TUNE button ) or turn the Tuning knob to right or left. Use these buttons for manual tuning. To move quickly through the channels, hold either of the RADIO TUNE buttons down for more than 1.5
seconds.

SEEK/SCAN tuning:

or

for less Push the SEEK button than 1.5 seconds, to tune from high to low or low to high frequencies and stops at the next broad- casting station. Push the SEEK button for more than 1.5 seconds to tune from low to high frequencies and stops at each broadcasting station for 5 seconds. Pushing the button again during this 5 seconds period will stop SCAN tuning and the radio will remain tuned to that station.

or

Display screen, heater, air conditioner and audio systems 4-29

墌 05.4.8/Z50-D/V5.0 墍

the SEEK button is not pushed within 5
If seconds, SCAN tuning moves to the next sta- tion. Station memory operations:

Eighteen (18) stations can be set for the FM, AM and SAT band to the A, B and C preset button.

1. Choose preset channel A, B or C using the

preset select button.

2. Tune to the desired station using the SEEK, SCAN or TUNE button and keep pushing any of the desired station memory buttons (1 to 6) until a beep sound is heard. (The radio mutes when the select button is pushed.)

3. The channel indicator will then come on and the sound will resume. Memorizing is now complete.

tions are in large cities, but many stations are now considering broadcasting RDS data.

PTY name selection can also be achieved by pushing the preset buttons.

Initial PTY names are stored in the preset but- tons; but these can be changed by pushing the preset buttons for less than 1.5 seconds when the desired PTY name is in the display.

RDS can display: 쐌 Station call sign, such as “WHFR 98.3”. 쐌 Station name, such as “The Groove”. 쐌 Music or programming type such as “Classi-

cal”, “Country”, or “Rock”.

쐌 Traffic reports about delays or construction. If the station broadcasts RDS information, the RDS icon is displayed.

Program type (PTY) (Category (CAT)):

4. Other buttons can be set in the same manner. If the battery cable is disconnected, or if the fuse blows, the radio memory will be erased. In that case, reset the desired stations. Radio data system (RDS): RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band) and/or SATELLITE band encoded within a regu- or lar radio broadcast. Currently, most RDS sta- 4-30 Display screen, heater, air conditioner and audio systems

When PROG/RPT button is pushed for more than 1.5 seconds during FM (SAT) mode, the PTY (CAT) name of the current tuned station is displayed. During this time if the PTY (CAT) data code is zero, or the data is unreadable; the display will show NONE. 1. PTY (CAT) selection mode

PTY (CAT) name selection can be done by the up/down TUNE button in the PTY (CAT) selection mode.

or

It is possible to shift the PTY (CAT) name by one step, with one push of the up/down tuning button

2. PTY SEEK tuning

After selecting a PTY name, push the SEEK button for less than 0.5 sec- onds within 10 seconds. Tuning to the PTY

or

墌 05.4.8/Z50-D/V5.0 墍

station will start. If you do not push the SEEK button within the 10 second period, the PTY mode will be canceled. Push the SEEK button for more than 1.5
seconds to tune the PTY name station, and stop at each broadcasting station for 5 sec- onds. Pushing the button again during this 5
second period will stop SCAN tuning and the radio will remain tuned to that station. If the SEEK button is not pushed within 5 seconds, SCAN tuning moves to the next station.

Cassette tape player operation (Type B) Turn the ignition switch to ACC or ON, and then lightly insert the cassette tape into the tape door. The cassette tape will be automatically pulled into the player. The radio or CD will turn off (if it is on) and the cassette tape will begin to play.

CAUTION

Do not force the cassette tape into the tape door. This could damage the player.

If the system is turned off by pushing the ON⋅OFF/VOL control knob with the cassette

tape still playing when the system is turned back on.

in the player, the tape will resume

PLAY:

쐌 When the TAPE button is pushed with the system turned off and a tape loaded, the system will come on and the tape will play. 쐌 When the TAPE button is pushed with either the radio or compact disc turned on and the tape loaded, the compact disc or the radio will automatically be turned off and the tape will play.

쐌 When the TAPE button is pushed with the TAPE playing, the tape will play the program recorded on the reverse side.

FF (Fast Forward), REW (Rewind): (fast

Push the forward) button to fast forward the tape. To rewind the tape, push the (rewind) button. Either the FF or REW symbol illuminates on the display window. To stop the FF or REW function, push the (rewind) again, or

(fast forward) or

the TAPE button.

APS (Automatic Program Search) FF, APS REW:

played, the next program will start to play from the beginning. Push the (APS FF) button several times to skip through programs. The tape will advance the number of times the button is pushed (up to nine programs).

(APS REW) button is pushed When the for less than 1.5 seconds once, the program being played starts over from the beginning. (APS REW) button several times Push the to skip back several selections. The tape will go back the number of times the button is pushed. Either the FF or REW symbol flashes on the display window while searching for the selec- tion.

the

When

pushing

(APS FF)

or (APS REW) button for more than 1.5
seconds, each program will play for about 10
seconds. To stop playing, push the button again. This system searches for the blank intervals between selections. If there is a blank interval within one program or there is no interval be- tween programs, the system may not stop in the desired or expected location.

REPEAT (RPT):

When the (APS FF) button is pushed for less than 1.5 seconds while the tape is being

When the PROG/RPT play button is pushed while the tape is played, the tape program play is repeated. To stop the repeat play, push the Display screen, heater, air conditioner and audio systems 4-31

墌 05.4.8/Z50-D/V5.0 墍

PROG/RPT play button again. Metal or chrome tape usage: The cassette player will be automatically set to high performance play when playing a metal or chrome cassette tape. TAPE EJECT:

When this button is pushed with the tape loaded, the tape will be ejected. When the tape is ejected while it is being played, the system will be turned off. Compact disc (CD) player operation (Type A) Turn the ignition switch to the ACC or ON position and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start playing. After loading the disc, the number of tracks on the disc and the play time will appear on the display. If the radio or tape is already operating, it will automatically turn off and the compact disc will play.

CAUTION

Do not force the compact disc into the slot. This could damage the player.

If the system has been turned off while the compact disc was playing, pushing the ON⋅OFF/VOL control knob will start the com- pact disc.

8 cm diameter compact discs can be used without an adapter.

PLAY:

When the CD button is pushed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play.

When the CD button is pushed with the com- pact disc loaded but the tape or the radio playing, the tape or radio will automatically be turned off and the compact disc will start to play.

FF (Fast Forward), REW (Rewind):

(fast forward) or

(rewind) When the button is pushed while the compact disc is being played, the compact disc will play while fast forwarding or rewinding. When the button is

4-32 Display screen, heater, air conditioner and audio systems

released, the compact disc will return to normal play speed.

APS (Automatic Program Search) FF, APS REW:

(APS FF) button is pushed for When the less than 1.5 seconds while the compact disc is being played, the program next to the present one will start to play from its beginning. Push several times to skip through programs. The compact disc will advance the number of times the button is pushed. (When the last program on the compact disc is skipped through, the first (APS program will be played.) When the REW) button is pushed for less than 1.5 sec- onds, the program being played returns to its beginning. Push several times to skip back through programs. The compact disc will go back the number of times the button is pushed.

the

When

pushing

(APS FF)

or (APS REW) button for more than 1.5
seconds, each track will play for about 10
button seconds. To stop playing, push the again.

REPEAT (RPT):

When the PROG/RPT play button is pushed while the compact disc is being played, the play pattern can be changed as follows:

墌 05.4.8/Z50-D/V5.0 墍

CD EJECT:

When the CD EJECT button is pushed with the compact disc loaded, the compact disc will be ejected.

When this button is pushed while the compact disc is being played, the compact disc will come out and the system will turn off. If the compact disc comes out and is not removed, it will be pulled back into the slot to protect it. (except 8 cm diameter com- pact discs) CD IN indicator: CD IN indicator appears on the display when the CD is loaded with the system on. Compact disc (CD) changer operation (Type B) Turn the ignition switch to the ACC or ON position and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start playing. To insert the disc, first push the LOAD button. After loading the disc, the number of tracks on

the disc and the play time will appear on the display. If the radio or tape is already operating, it will automatically turn off and the compact disc will play.

CAUTION

Do not force the compact disc into the slot. This could damage the player.

If the system has been turned off while the compact disc was playing, pushing the ON⋅OFF/VOL control knob will start the com- pact disc.

3.1 inches (8 cm) diameter discs cannot be used (even with an adapter).

button:

PLAY:

When the CD button is pushed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play.

When the CD button is pushed with the com- pact disc loaded with the tape or the radio playing, the tape or radio will automatically be turned off and the compact disc will start to play.

FF (Fast Forward), REW (Rewind):

(fast forward) or

(rewind) When the button is pushed while the compact disc is being played, the compact disc will play while fast forwarding or rewinding. When the button is released, the compact disc will return to normal play speed.

APS (Automatic Program Search) FF, APS REW:

To insert a CD in the CD changer, push the LOAD button for less than 1.5 seconds. Select the loading slot by pushing the CD insert select button (1 to 6), then insert the CD.

To insert 6 CDs to the CD changer, push the LOAD button for more than 1.5 seconds. The inserted slot numbers will illuminate on the display.

(APS FF) button is pushed for When the less than 1.5 seconds while the compact disc is being played, the program next to the present one will start to play from its beginning. Push several times to skip through programs. The compact disc will advance the number of times the button is pushed. (When the last program on the compact disc is skipped through, the first program will be played.) When the (APS REW) button is pushed for less than 1.5 sec- Display screen, heater, air conditioner and audio systems 4-33

墌 05.4.8/Z50-D/V5.0 墍

onds, the program being played returns to its beginning. Push several times to skip back through programs. The compact disc will go back the number of times the button is pushed.

the

When

pushing

(APS FF)

or (APS REW) button for more than 1.5
seconds, each track will play for about 10
seconds. To stop playing, push the button again. CD PLAY button: To change CD, push the CD play select button (1 to 6). You can select if the CD is inserted.

more than 1.5 seconds. When this button is pushed while the compact disc is being played, the compact disc will come out and the system will turn off. If the compact disc comes out and is not removed, it will be pulled back into the slot to protect it. CD IN indicator: CD IN indicator appears on the display when the CD is loaded with the system on.

REPEAT (RPT):

When the PROG/RPT play button is pushed while the compact disc is played, the play pattern can be changed as follows:

CD EJECT:

When the CD EJECT button is pushed with the compact disc loaded, the compact disc will be ejected. To eject the selected discs by the EJECT button, push it for less than 1.5 seconds. To eject all the discs, push the EJECT button for 4-34 Display screen, heater, air conditioner and audio systems

SAA0451

CD CARE AND CLEANING 쐌 Handle a CD by its edges. Never touch the

surface of the disc. Do not bend the disc.

쐌 Always place the discs in the storage case

when they are not being used.

쐌 To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion. Do not use a conventional record cleaner or alcohol intended for industrial use.

쐌 A new disc may be rough on its inner and outer edges. Remove the rough edges using the side of a pen or pencil as illustrated.

墌 05.4.8/Z50-D/V5.0 墍

tween programs, the system may not stop in the desired or expected location. FF REW (tape or CD): Push the tuning switch for more than 1.5 seconds to rewind or fast forward the tape or to change the playing disc up or down. To stop the FF or REW function, push the button for less than 1.5 seconds

or

or

again.

MODE select switch Push the mode select switch to change the mode in the sequence of FM, AM, SAT, CD and Tape. Volume control switch Push up or down the volume control switch to increase or decrease the volume.

or

or

Tuning Memory change (radio): for less Push the tuning switch than 1.5 seconds to change the radio frequency. Seek tuning (radio): for more Push the tuning switch than 1.5 seconds to seek the next or previous radio station. APS (Automatic Program Search) FF, APS REW (tape and CD): Push the tuning switch for less than 1.5 seconds to return to the beginning of the present program or skip to the next program. Push several times to skip back or skip through programs. This system searches for the blank intervals between selections. If there is a blank interval within one program or there is no interval be-

or

SAA0963

1. Volume control switch 2. MODE select switch 3. POWER on/off switch 4. Memory change⋅Seek and APS switch STEERING SWITCH FOR AUDIO CONTROL (if so equipped) The audio system can be operated using the controls on the steering wheel. POWER on/off switch With the ignition switch turned to the ACC or ON position, push the POWER on/off switch to turn the audio system on or off.

Display screen, heater, air conditioner and audio systems 4-35

墌 05.4.8/Z50-D/V5.0 墍

CAR PHONE OR CB RADIO

Removing the antenna You can remove the antenna if necessary. Hold the bottom of the antenna and remove by turning counterclockwise.

When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following cautions, otherwise the new equipment may adversely affect the Engine control system and other electronic parts.

CAUTION

WARNING

쐌 Be sure that antenna is removed be-