Download PDF Manual

panel. Also, do not place any objects between any occupant and the steer- ing wheel or instrument panel. Such objects may become dangerous pro- jectiles and cause injury if the supple- mental air bag inflates.


I Right after inflation, several supple-


the steering wheel;


Supplemental air bag system The driver supplemental air bag is located in the center of the front passenger supplemental air bag is mounted in the dashboard above the glove box. The supplemental air bag system is designed to inflate in higher severity frontal collisions, al- though it may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. It may not inflate in certain frontal collisions. Vehicle damage (or lack of it) is not always an indication of proper supplemental air bag operation. When the supplemental air bag inflates, a fairly


SPA0103A


loud noise may be heard, followed by release of smoke. This smoke is not harmful and does not indicate a fire, but care should be taken not to intentionally inhale it, as it may cause irrita- tion and choking. Those with a history of breathing trouble should get fresh air promptly.


Supplemental air bags, along with the use of seat belts, help to cushion the impact force on the face and chest of the occupant. They can help save lives and reduce serious injuries. However, an inflating supplemental air bag may cause facial abrasions or other injuries. Supplemental air bags do not provide restraint to the lower body.


2-20


Z 01.2.1/A32-D X


I Work around and on the supplemen- tal air bag system should be done by an authorized NISSAN dealer. Instal- lation of electrical equipment should also be done by an authorized NISSAN dealer. The SRS wiring har- nesses should not be modified or disconnected. Unauthorized electri- cal test equipment and probing de- vices should not be used on the supplemental air bag system.


I The SRS wiring harnesses are cov- ered with yellow insulation either just before the harness connectors or for the complete harness, for easy identification.


When selling your vehicle, we request that you inform the buyer about the supplemental air bag system and guide the buyer to the appro- priate sections in this Owner’s Manual.


mental air bag system components will be hot. Do not touch them; you may severely burn yourself.


I No unauthorized changes should be made to any components or wiring of the supplemental air bag system. This is to prevent accidental inflation of the supplemental air bag or dam- age to the supplemental air bag sys- tem.


I Do not make unauthorized changes to your vehicle’s electrical system, suspension system or front end structure. This could affect proper operation of the supplemental air bag system.


I Tampering with the supplemental air bag system may result in serious personal injury. Tampering includes changes to the steering wheel and the instrument panel assembly by placing material over the steering wheel pad and above the dashboard, or by installing additional trim mate- rial around the supplemental air bag system.


2-21


Z 01.2.1/A32-D X


SUPPLEMENTAL AIR BAG WARNING LABELS


SUPPLEMENTAL AIR BAG WARNING LIGHT


Warning labels about the supplemental air bag system are placed in the vehicle.


SPA0104A


SPA0105


The supplemental air bag light, displaying “AIR BAG” in the instrument panel, monitors the circuits of the supplemental air bag. The cir- cuits monitored by the supplemental air bag light are the diagnosis sensor unit, supplemen- tal air bag modules and all related wiring. When the ignition key is in the “ON” or “START” position, the supplemental air bag light will illuminate for about 7 seconds and then turn off. This means the system is opera- tional.


2-22


Z 01.2.1/A32-D X


should be inspected by an authorized NISSAN dealer if there is any damage to the front end portion of the vehicle. I If you need to dispose of a supple- mental air bag or scrap the vehicle, contact an authorized NISSAN dealer. Correct supplemental air bag dis- posal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury.


If any of the following conditions occurs, the supplemental air bag needs servicing:


1. The supplemental air bag light goes off


within 7 seconds.


2. The supplemental air bag light flashes in- termittently or remains on (after 7 seconds).


3. The supplemental air bag light does not


come on at all.


Under these conditions, the Supplemental Re- straint System Air Bag may not operate prop- erly. It must be checked and repaired.


Take your vehicle to the nearest authorized NISSAN dealer.


inflation has occurred. Repair and replace- ment of the supplemental air bag system should be done only by authorized NISSAN dealers. To ensure long-term functioning, the sys- tem must be inspected 10 years after the date of manufacture noted on the certifica- tion label located on the driver side center pillar.


When maintenance work is required on the vehicle, the supplemental air bag system and related parts should be pointed out to the person conducting the maintenance. The igni- tion key should always be in the “LOCK” position when working under the hood or in- side the vehicle.


If the supplemental air bag warning light is on, it could mean that the supplemen- tal air bag will not operate in an accident.


Repair and replacement procedure The supplemental air bag system is designed to inflate on a one-time-only basis. As a re- minder, unless it is damaged, the supplemen- tal air bag light will remain illuminated after


I Once the supplemental air bag has inflated, the supplemental air bag module will not function again and must be replaced. The supplemental air bag module should be replaced by an authorized NISSAN dealer. The supplemental air bag module cannot be repaired.


I The supplemental air bag system


2-23


Z 01.2.1/A32-D X


SEAT BELTS


PRECAUTIONS ON SEAT BELT USAGE Your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced if you are wearing your seat belt and it is properly adjusted. NISSAN strongly encourages you and all of your pas- sengers to buckle up every time you drive, even if your seating position includes a supple- mental air bag. Some states, provinces or territories re- quire that seat belts be worn at all times when a vehicle is being driven.


SPA0506


SPA0485


I Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly restrained and, in a child restraint.


if appropriate,


I The belt should be adjusted properly and to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the


2-24


chance or severity of injury in an accident. Serious injury or death can occur if the seat belt is not worn properly.


I Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your backs under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder.


I Position the lap belt as low and snug


Z 01.2.1/A32-D X


I Never carry more people in the ve-


hicle than there are seat belts.


I If the seat belt warning lamp glows continuously while the ignition is turned “ON” with all doors closed and all seat belts fastened, it may indicate a malfunction in the system. Have the system checked by your NISSAN dealer.


I All seat belt assemblies including re- tractors and attaching hardware should be inspected by your NISSAN dealer after any collision. NISSAN recommends that all seat belt assem- blies in use during a collision be replaced unless the collision was mi- nor and the belts show no damage and continue to operate properly. Seat belt assemblies not in use dur- ing a collision should also be in- spected and replaced if either dam- age or improper operation is noted.


CHILD SAFETY Children need adults to help protect them.


Infants and children need special pro- tection. The vehicle’s seat belts may not fit them properly. The shoulder belt may come too close to the face or neck. The lap belt may not fit over their small hip bones. In an accident, an improperly fitting seat belt could cause serious or fatal injury. Always use appropriate child restraints.


All U.S. states and provinces of Canada re- quire the use of approved child restraints for infants and small children. (See “Child re- straints for infants and small children” later in this section.)


In addition, there are many types of child restraints available for larger children which should be used for maximum protection. Infant or small child NISSAN recommends that infants or small children be placed in child restraints that com- ply with Federal Motor Vehicle Safety Stan- dards or Canadian Motor Vehicle Safety Stan- dards. You should choose a child restraint that fits your vehicle and always follow the manu-


2-25


Z 01.2.1/A32-D X


SPA0486


as possible AROUND THE HIPS, NOT THE WAIST. A lap belt worn too high could increase the risk of internal injuries in an accident.


I Be sure the seat belt tongue is se- curely fastened to the proper buckle. I Do not wear the belt inside out or twisted. Doing so may reduce its ef- fectiveness.


I Do not allow more than one person to


use the same belt.


facturer’s instructions for installation and use. Children Children who are too large for child restraint systems should be seated and restrained by the seat belts which are provided. NISSAN recommends that children sit in the rear seat if possible. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat. If the child’s seating position has a shoulder belt that fits close to the face or neck, the use of a booster seat (commercially available) may help overcome this. The booster seat should raise the child so that is properly positioned across the top, middle portion of the shoulder and the lap belt is low on the hips. The booster seat should fit the vehicle seat and have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. Once the child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat.


the shoulder belt


Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is moving. The child could be seriously injured or killed in an accident.


PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts. Contact your doctor for specific recommendations. The lap belt should be worn snug and positioned as low as possible around the hips, not the waist. INJURED PERSONS NISSAN recommends that injured persons use seat belts, depending on the injury. Check with your doctor for specific recommendations.


3-POINT TYPE SEAT BELT WITH RETRACTOR


SPA0492


Every person who drives or rides in this vehicle should wear a seat belt at all times.


Fastening the belts 1. Adjust the seat.


2-26


Z 01.2.1/A32-D X


and adjust the seat belt properly.


SPA0493


Do not ride in a moving vehicle when the seatback is reclined. This can be dan- gerous. The shoulder belt will not be against your body. In an accident you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive se- rious internal injuries.


For most effective protection when the vehicle is in motion, the seat should be upright. Always sit well back in the seat


PD1024M


2. Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until it snaps.


The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion will permit the belt to move, and allow you some freedom of movement in the seat. 3. Position the lap belt portion low and snug


on the hips as shown.


4. Pull the shoulder belt portion toward the


retractor to take up extra slack.


The front passenger side seat belt and rear


2-27


Z 01.2.1/A32-D X


3-point seat belts have a cinching mechanism for child seat installation. It is referred to as the automatic locking mode. When the cinching mechanism is activated the seat belt cannot be withdrawn again until the seat belt tongue is detached from the buckle and fully retracted. Refer to “Child restraints for infants and small children” later in this section for more information. The automatic locking mode should be used only for child seat installation. During normal seat belt use by a passenger, the locking mode should not be activated. If it is activated it may cause uncomfortable seat belt tension. Unfastening the belts To unfasten the belt, press the button on the buckle. The seat belt will automatically retract.


Checking seat belt operation (3-point type with retractor) Your seat belt retractors are designed to lock belt movement using two separate methods: 1) When the belt is pulled quickly from the


retractor.


2) When the vehicle slows down rapidly. You can check their operation as follows: I Grasp the shoulder belt and pull quickly forward. The retractor should lock and re- strict further belt movement.


If the retractor does not lock during this check or if you have any questions about belt opera- tion, see your NISSAN dealer.


PD1321-A


Shoulder belt height adjustment (For front seats) The shoulder belt anchor height should be adjusted to the position best for you. (See “Precautions on seat belt usage”.) To adjust, squeeze the release buttons, and then move it to the desired position, so that the belt passes over the center of the shoulder. The belt should be away from your face and neck, but not falling off of your shoulder.


2-28


Z 01.2.1/A32-D X


After adjustment, release the button and check that it does not move up and down to make sure the shoulder belt anchor is securely fixed in position.


SPA0281


SPA0278


2-POINT TYPE WITHOUT RETRACTOR (center position of rear seat) Selecting correct set of belts The center seat belt buckle and tongue are identified by the CENTER mark. The center seat belt tongue can be fastened only into the center seat belt buckle.


Fastening the belts 1. Insert the tongue into the buckle marked


CENTER until it snaps.


2-29


Z 01.2.1/A32-D X


SPA0469


SPA0280


2. To lengthen, hold the tongue at a right angle to the belt and pull on the belt. To shorten, pull the end of the belt attached to the belt clip away from the tongue, and then pull the belt clip to take up the slack.


3. Position the lap belt low and snug on the


hips as illustrated.


Unfastening the belts To unfasten the belt, press the button on the buckle.


SEAT BELT EXTENDERS If, because of body size or driving position, it is not possible to properly fit the lap-shoulder belt and fasten it, an extender is available which is compatible with the installed seat belts. The extender adds approximately 8 inches (200
mm) of length and may be used for either the driver or front passenger seating position. See your NISSAN dealer for assistance if the ex- tender is required.


I Only NISSAN belt extenders, made by the same company which made the original equipment belts, should be used with NISSAN belts.


I Persons who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident.


2-30


Z 01.2.1/A32-D X


SEAT BELT MAINTENANCE I To clean the seat belt webbings, apply a mild soap solution or any solution recom- mended for cleaning upholstery or carpets. Then brush the webbing, wipe it with a cloth and allow it to dry in the shade. Do not allow the seat belts to retract until they are com- pletely dry.


I If dirt builds up in the shoulder belt guide of the seat belt anchors, the seat belts may retract slowly. Wipe the shoulder belt guide with a clean, dry cloth.


I Periodically check to see that the seat belt and the metal components such as buckles, tongues, retractors, flexible wires and anchors work properly. If loose parts, deterioration, cuts or other damage on the webbing is found, the entire belt assembly should be replaced.


CHILD RESTRAINTS FOR INFANTS AND SMALL CHILDREN


I Infants and small children should al- ways be placed in an appropriate child restraint while riding in the ve- hicle. Failure to use a child restraint can result in serious injury or death. I Children and infants should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe accident. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself.


I Nissan recommends that the child restraint be installed in the rear seat. According to accident statistics, chil- dren are safer when properly re- strained in the rear seat than in the front seat.


I An improperly installed child re- straint could lead to serious injury or death in an accident.


In general, child restraints are designed to be


2-31


installed with a lap belt or the lap portion of a three-point type seat belt. Child restraints specially designed for infants and small children are offered by several manufacturers. When selecting any child re- straint, keep the following points in mind:


1) Choose only a restraint with a label certify- ing that it complies with Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213.


2) Check that child restraint in your vehicle to be sure it is compatible with the vehicle’s seat and seat belt system. Choose a child restraint that meets the guidelines of the Society of Automotive Engineers recom- mended practice J1819 for child restraint installation.


3) If the child restraint is compatible with your vehicle, place your child in the child re- straint and check the various adjustments to be sure the child restraint is compatible with your child. Always follow all recom- mended procedures.


All U.S. states and provinces of Canada require that infants and small children be restrained in approved child restraints at all times while the vehicle is being oper- ated.


Z 01.2.1/A32-D X


Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint.


tioned to fit the child restraint, but as upright as possible.


I After attaching the child restraint, test it before you place the child in it. Tilt it from side to side. Try to tug it forward and check to see if the belt holds the restraint in place. If the restraint is not secure, tighten the belt as necessary, or put the restraint in another seat and test it again.


I For a front facing child restraint, if the seat position where it is installed has a 3-point type lap/shoulder belt, check to make sure the shoulder belt does not go in front of the child’s face or neck. If it does, put the shoulder belt behind the child restraint.


I When your child restraint is not in use, keep it secured with a seat belt to prevent from being thrown around in case of a sudden stop or accident.


it


I Never install a rear-facing child re- straint in the front seat. An inflating supplemental air bag could seriously injure or kill your child. A rear-facing child restraint must only be used in the rear seat. See “Installation on front passenger seat” for details.


I Improper use of a child restraint can result in increased injuries for both the infant or child and other occu- pants in the vehicle.


I Follow all of the child restraint manu- facturer’s instructions for installation and use. When purchasing a child restraint, be sure to select one which will fit your child and vehicle. It may not be possible to properly install some types of child restraints in your vehicle.


I If the child restraint is not anchored properly, the risk of a child being injured in a collision or a sudden stop greatly increases.


I Adjustable seatbacks should be posi-


2-32


Z 01.2.1/A32-D X


facturer’s instructions for belt routing.


3. Remove all slack in the lap belt for a very tight fit by pulling forcefully on the lap belt adjustment.


4. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place.


5. If it is not secure, try to tighten the belt again, or put the restraint in another seat. 6. Check to make sure the child restraint is


properly secured prior to each use.


PD1174


2-33


Z 01.2.1/A32-D X


SPA0276


Installation on rear center seating position When you install a child restraint in a rear center seat, follow these steps: 1. Position the child restraint on the seat as illustrated. It can be placed in a front facing or rear facing direction, depending on the size of the child. Always follow the restraint manufacturer’s instructions.


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu-


in a sudden stop or collision.


When you install a child restraint in a rear outboard seat, follow these steps: 1. Position the child restraint on the seat. It can be placed in a front facing or rear facing direction, depending on the size of the child. Always follow the restraint manufac- turer’s instructions.


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manu- facturer’s instructions for belt routing.


3. Pull on the shoulder belt until all of the belt is fully extended and a click is heard. At this time, the belt retractor is in the automatic locking mode (child restraint mode). It will revert back to “emergency locking” when the belt is fully retracted.


4. Allow the belt to retract. A clicking sound will be heard as the belt retracts. This indicates that the retractor is in the auto- matic locking mode. Pull up on the belt


Installation on rear outboard seating positions


PD1331


I The 3-point belt on your vehicle is equipped with a locking mode retrac- tor which must be used when install- ing a child restraint.


I Failure to do so will result in the child restraint not being properly secured. It could tip over or otherwise be un- secured and cause injury to the child


PD1332


to remove any slack in the belt.


5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place.


6. Check that the retractor is in the automatic locking mode by trying to pull more belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the belt is in the automatic locking mode.


7. Check to make sure that the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 6.


2-34


Z 01.2.1/A32-D X


After the child restraint is removed and the seat belt is allowed to wind back into the retractor, the automatic locking mode (child restraint mode) is canceled; the seat belt may be used as normal and will only lock during a sudden stop or impact.


Bolt length: more than 1.18 in (30 mm) Thread pitch: 1.25 mm


The top strap should be secured to the attach- ing bolt which provides the straightest installa- tion of the top strap.


Child restraint anchor points are de- signed to withstand only those loads imposed by correctly fitted child re- straints. Under no circumstances are they to be used for adult seat belts or harnesses.


APD0107


Top strap child restraint If your child restraint has a top strap, install the anchor bracket to the provided anchor point. The top strap anchor bracket is available through your NISSAN dealer.


Part No. 88894-89900


Secure the child restraint with the center lap belt or the lap portion of an outboard 3-point belt and latch the top strap hook onto the appropriate anchor bracket. To install the an- chor bracket, a metric bolt of the dimensions listed below must be used. Bolt diameter: 8.0 mm 2-35


Z 01.2.1/A32-D X


are pre-cut circles at each anchor point location that should break away from the shelf support material when pressure is applied to them. Remove the bolt after you feel the pre-cut circle separate from the shelf support material.


2. Cut a small slit through the parcel shelf fabric at the anchor point location. Reach through the fabric with a tool such as a pair of needle-nose pliers and remove the pre- cut circle in the parcel shelf support mate- rial.


SPA0117


3. Install the bolt through the top strap hook


and into the anchor point nut.


4. Be sure to follow all of the instructions that accompany the top strap attaching hard- ware.


Your NISSAN dealer can assist you with the installation of your child restraint.


Anchor point locations Anchor points are located under the rear par- cel shelf finisher.


To use attaching hardware for child restraints with top straps, follow these instructions care- fully:


1. Open the trunk and find the anchor point nuts on the under side of the rear parcel shelf. Thread a bolt (8.0 mm diameter, 1.25
pitch) up through the nut behind the seating position where the child restraint will be installed and use it to break through the rear parcel shelf support material. There


2-36


Z 01.2.1/A32-D X


I Failure to use the retractor’s locking mode may result in the child restraint not being properly secured. The re- straint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision.


When you install a child restraint in the front seat, follow these steps: 1. Position the child restraint on the front passenger seat. It should be placed in a front-facing direction only. Move the seat as far back from the instrument panel as possible. Always follow the child restraint instructions. Child re- manufacturer’s straints for infants must be used in the rear-facing direction and therefore must not be used in the front seat.


2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage.


SPA0487


SPA0483


Installation on front passenger seat


I Never install a rear-facing child re- straint in the front passenger seat. Supplemental air bags inflate with great force. A rear-facing child re- straint could be struck by the supple- mental air bag in a crash and could seriously injure or kill your child.


I If you install a front-facing child re- straint in the front passenger seat, place the passenger seat as far back as possible.


I A child restraint with a top strap should not be used in the front pas- senger seat.


I The 3-point belt in your vehicle is equipped with a locking mode retrac- tor which must be used when install- ing a child restraint.


2-37


Z 01.2.1/A32-D X


TILTING STEERING WHEEL


5. Before placing the child in the child re- straint, use force to tilt the child restraint from side to side, and tug it forward to make sure that it is securely held in place.


6. Check that the retractor is in the automatic locking mode by trying to pull more belt out of the retractor. If you cannot pull any more belt webbing out of the retractor, the belt is in the automatic locking mode.


7. Check to make sure that the child restraint is properly secured prior to each use. If the lap belt repeat steps 3
through 6.


locked,


is not


PD1336


Be sure to follow the child restraint manufac- turer’s instructions for belt routing.


3. Pull on the shoulder belt until all of the belt is fully extended and a click is heard. At this time, the belt retractor is in the automatic locking mode (child restraint mode). (It will revert back to “emergency locking” when the belt is fully retracted.)


4. Allow the belt to retract. A clicking sound will be heard as the belt retracts. This indicates that the retractor is in the auto- matic locking mode. Pull up on the belt to remove any slack in the belt.


After the child restraint is removed and the seat belt is allowed to wind back into the retractor, the automatic locking mode (child restraint mode) is canceled; the seat belt may be used as normal and will only lock during a sudden stop or impact.


SPA0111


Tilt operation Push the lock lever and while holding down, adjust the steering wheel up or down to the desired position. Push the lock lever back into place to lock the steering wheel in place.


Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.


2-38


Z 01.2.1/A32-D X


OUTSIDE MIRROR REMOTE CONTROL


FOLDABLE OUTSIDE MIRRORS


Push the right or left end of the switch to select the right or left outside mirror, then adjust using the control lever.


SPA0112


Push the outside mirror backward to fold it.


MPA0008


Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use inside mirror or glance over your shoulder to properly judge distances to other objects.


The outside mirror will operate only when the ignition switch is in the “ACC” or “ON” position.


2-39


Z 01.2.1/A32-D X


INSIDE MIRROR


The night position will reduce glare from the headlights of vehicles behind you at night.


SPA0470


Use the night position only when neces- sary, because it reduces rear view clarity.


2-40


Z 01.2.1/A32-D X


3 Heater, air conditioner and audio system


Ventilator ................................................................... 3-2
Heater and air conditioner......................................... 3-3
Automatic air conditioner (if so equipped) ................ 3-9
Radio ....................................................................... 3-11
Antenna ................................................................... 3-28
CB radio or car phone ............................................ 3-29


Z 01.2.1/A32-D X


VENTILATOR


SAA0040


SAA0041


Center ventilators Adjust the air flow direction of ventilators.


Side ventilators Open or close, and adjust the air flow direction of ventilators.


: This symbol


indicates that the vents are closed when the vent switch is moved to the left.


: This symbol


indicates that the vents are open when the vent switch is moved to the right.


3-2


Z 01.2.1/A32-D X


HEATER AND AIR CONDITIONER


I The air conditioner cooling function operates only when the engine is run- ning.


I Do not


leave children, unreliable adults, or pets alone in your vehicle. On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or


SAA0042A


animals.


I Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.


I Positioning of the heating or air con- ditioning controls should not be done while driving, in order that full attention may be given to the driving operation.


CONTROLS Fan control dial This dial turns the fan on and off, and controls fan speed. Air flow control buttons These buttons allow you to select the air flow outlets.


— Air flows from center and side venti-


lators.


— Air flows from center and side venti-


lators and foot outlets.


— Air flows mainly from foot outlets. — Air flows from defroster outlets and


foot outlets.


— Air flows mainly from defroster out-


lets.


Temperature control lever This lever allows you to adjust the temperature of the outlet air.


3-3


Z 01.2.1/A32-D X


Air recirculation button OFF position Outside air is drawn into the passenger com- partment. Use the off position for normal heater, or air conditioner operation. ON position (Indicator light ON) Interior air is recirculated inside the vehicle. Push the air recirculation button to the “ON” position when driving on a dusty road or to avoid traffic fumes and for maximum cooling when using the air conditioner. Air conditioning button This button is provided only for vehicles with air conditioner. Start the engine, move the fan control dial to the desired (1 to 4) position and push the air conditioning button to turn on the air condi- tioner. The indicator light will come on when the air conditioner is on. To stop the air con- ditioner, push the switch again to return it to the original position. The air conditioner cooling function oper- ates only when the engine is running.


HEATER OPERATION Heating This mode is used to direct hot air from the floor outlets. Some air will also come from the defrost vents.


1. Push the air recirculation button to the


“OFF” position for normal heating.


2. Push the “


” button in.


3. Turn on the fan control dial.


4. Move the temperature control lever to the desired position between the middle and the “HOT” position.


I For quick heating, move the air recirculation button to the “ON” position. Be sure to return the air recirculation button to the “OFF” position for normal heating.


Ventilation This mode directs outside air from the side and center vents.


1. Push the air recirculation button to the


“OFF” position.


2. Push the “


” button in.


3. Turn on the fan control dial.


3-4


4. Move the temperature control lever to the


desired position.


Defrosting or defogging This mode is used to defrost/defog the win- dows. 1. Push the “ ” button in. 2. Turn on the fan control dial. 3. Move the temperature control lever to the desired position between the middle and the “HOT” position.


I To quickly remove ice or fog from the windows, turn on the fan control dial to “4” and the temperature control lever to the full “HOT” position.


I When the “


” switch is pushed, the air conditioner will automatically be turned on to defog the windshield, and the air recircu- late mode will automatically be turned off. Outside air is drawn into the passenger compartment to improve the defogging per- formance.


Z 01.2.1/A32-D X


Bi-level heating This mode directs outside air from the side and center vents and hot air from the floor outlets. 1. Push the air recirculation button to the


“OFF” position.


” button in.


2. Push the “ 3. Turn on the fan control dial. 4. Normally move the temperature control le- ver to the midpoint between “HOT” and “COLD”.


Heating and defogging This mode heats the interior and defogs the windshield. 1. Push the “ 2. Turn on the fan control dial. 3. Move the temperature control lever to the desired position between the middle and the “HOT” position.


” button in.


Operating tips I Clear snow and ice from the wiper blades and air inlet in front of the wind- shield. This will improve heater opera- tion.


I When the “


” switch is pushed, the air recirculate mode will automatically be turned off. Outside air is drawn into the passenger compartment to improve the defogging per- formance.


AIR CONDITIONER OPERATION Start the engine, move the fan control dial to the desired (1 to 4) position and push in the air conditioning button to activate the air condi- tioner. When the air conditioner is on, cooling and dehumidifying functions will be added to the heater operation. Cooling This mode is used to cool and dehumidify. 1. Push the air recirculation button to the


“OFF” position.


” button in.


2. Push the “ 3. Turn on the fan control dial. 4. Push on the air conditioning button. The


indicator light will come on.


5. Move the temperature control lever to the


desired position.


I For quick cooling when the outside tem- perature is high, move the air recirculation button to the “ON” position. Be sure to return the air recirculation button to the “OFF” position for normal cooling.


3-5


Z 01.2.1/A32-D X


AIR FLOW CHART The chart below shows the switch and lever positions for MAXIMUM and QUICK heating, cooling or defrosting. The air recirculation switch should be in the “OFF” position for normal cooling, heating and defrosting.


Dehumidified heating This mode is used to heat and dehumidify.


1. Push the air recirculation button to the


“OFF” position.


2. Push the “


” button in.


3. Turn on the fan control dial.


4. Push on the air conditioning button. The


indicator light will come on.


5. Move the temperature control lever to the


desired position.


Dehumidified defogging This mode is used to defog the windows and dehumidify.


1. Push the “


” button in.


2. Turn on the fan control dial.


3. Push on the air conditioning button. The


indicator light will come on.


4. Move the temperature control lever to the


desired position.


When the “ ” button is pushed, the air conditioner will automatically be turned on to defog the windshield, and the air recircu- late mode will automatically be turned off.


Outside air is drawn into the passenger com- partment to improve the defogging perfor- mance. Operating tips I Keep the windows and sun roof closed


while the air conditioner is in operation.


I After parking in the sun, drive for two or three minutes with the windows open to vent hot air from the passenger compart- ment. Then, close the windows. This will allow the air conditioner to cool the interior more quickly.


I The air conditioning system should be operated for about ten minutes at least once a month. This helps prevent dam- age to the system due to lack of lubrica- tion.


I If the coolant temperature gauge exceeds the HOT position, turn the air conditioning off. See “If your vehicle overheats” in the “In case of emergency” section for additional information.


3-6


Z 01.2.1/A32-D X


SAA0058C


3-7


SAA0059C


Z 01.2.1/A32-D X


SAA0060C


3-8


SAA0061C


Z 01.2.1/A32-D X


AUTOMATIC AIR CONDITIONER (if so equipped)


Start the engine and operate the controls to activate the air conditioner. Cooling and/or dehumidified heating (Auto mode) This mode may be normally used all year round as the system automatically works to keep a constant temperature. Air flow distribu- tion and fan speed are also controlled auto- matically.


1. Push the AUTO button on. (“AUTO” will be


displayed.)


SAA0043B


2. Push


the


” “


“ ture.


temperature button ” to set the desired tempera-


set


I The air conditioner cooling function operates only when the engine is run- ning.


I Do not


leave children, unreliable adults, or pets alone in your vehicle. On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or


animals.


I Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.


I Positioning of the heating or air con- ditioning controls should not be done while driving, in order that full attention may be given to the driving operation.


I Adjust the temperature set button to about


75°F (24°C) for normal operation.


I The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution and fan speed are also controlled automatically. Heating (ECON mode) The air conditioner does not activate. When you need to heat only, use this mode. 1. Push the ECON (ECONOMY) button on.


(“ECON” will be displayed.)


3-9


Z 01.2.1/A32-D X


2. Push


the


” “


“ ture.


button temperature ” to set the desired tempera-


set


I The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution and fan speed are also controlled automatically.


I Do not set the temperature lower than the outside air temperature. Otherwise the sys- tem may not work properly.


I Not recommended if windows fog up. Dehumidified defogging 1. Push the DEF “


” button on. (The indicator light on the button will come on.) temperature button ” to set the desired tempera-


2. Push


the


set


” “


“ ture.


I To quickly remove ice or fog from the outside of the windows, push the manual fan control button “ ” and set to the ”. maximum position “


I As soon as possible after the windshield is clean, push the AUTO button to return to the auto mode.


I When the DEF “


” button is pushed, the air conditioner will automatically be


selects the air outlet to:


: Air flows from center and side ventila-


tors.


: Air flows from center and side ventila-


tors and foot outlets.


: Air flows mainly from foot outlets.


To turn system off Push the OFF button. Operating tips I When the engine coolant temperature and outside air temperature are low, the air flow from the foot outlets may not operate for a maximum of 150 seconds. However, this is not a malfunction. After the coolant tem- perature warms up, the air flow from the foot outlets will operate normally.


turned on at outside temperatures above 35°F (2°C) to defog the windshield, and the air recirculate mode will automatically be turned off.


Outside air is drawn into the passenger compartment to improve the defogging per- formance.


Manual fan speed control Push the fan control button “ ally control the fan speed. I Push the AUTO button to return to auto-


” to manu-


matic control of the fan speed.


Air recirculation button Push the air recirculation button “ ” to recirculate interior air inside the vehicle. The indicator light on the switch will come on. Push it again to draw outside air into the passenger compartment. The indicator will go out. I The air recirculation button will not be acti- vated when the air conditioner is in DEF mode.


Manual air flow control button “MODE” Pushing the manual air flow control button


3-10


Z 01.2.1/A32-D X


RADIO


To turn the radio on, turn the ignition key to “ACC” or “ON”. If you listen to the radio with the engine not running, turn the key to the “ACC” position. Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external influences. Intermittent changes in reception quality normally are caused by these external influences.


Servicing air conditioner The air conditioning system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. This refrigerant will not harm the earth’s ozone layer. How- ever, special charging equipment and lubricant are required when servicing your NISSAN air conditioner. Using improper refrigerants or lu- bricants will cause severe damage to your air conditioning system. See AIR CONDITION- ING SYSTEM REFRIGERANT AND LUBRI- CANT RECOMMENDATIONS in the TECHNI- CAL AND CONSUMER INFORMATION section of this manual. Your NISSAN dealer will be able to service your environmentally “friendly” air conditioning system.


HA1011


The sensor on the instrument panel helps maintain a constant temperature; do not put anything on or around this sensor.


3-11


Z 01.2.1/A32-D X


FM/AM RADIO WITH CASSETTE PLAYER Radio operation Push the ON/VOL knob to listen to the radio and tune in the desired station.


Pushing the “ ” button while the cas- sette tape is playing will turn off the cassette player and turn on the radio.


Turn the ON/VOL knob to adjust the volume.


Inserting a cassette tape into the cassette player while the radio is on will turn off the radio and turn on the cassette player.


The electronic tuning radio has a DIVERSITY reception system. The FM signal can reflect off of buildings or mountains. This causes offen- sive noise. The DIVERSITY system employs two antennas; one is a rod type antenna and the other is a printed antenna on the rear window. This system automatically switches to the antenna which receives less noise. Thus the radio provides high quality reception. Selecting the desired band Push the band select button “ change from AM to FM reception. The stereo indicator will glow during FM stereo


” to


SAA0044B


3-12


Z 01.2.1/A32-D X


reception. When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception. Tuning


SEEK tuning ” Push the SEEK/SCAN tuning button “ for less than 1.5 seconds. SEEK tuning begins from low to high frequencies and stops at the next broadcasting station.


The radio should not be tuned while driving in order that full attention may be given to the driving operation.



” button.


tuning “


Manual tuning Push down either manual “ SCAN tuning Push the SEEK/SCAN tuning button “ ” for more than 1.5 seconds. SCAN tuning be- gins from low to high frequencies and stops at each broadcasting station for five seconds. Pushing the button again during this five sec- ond period will stop SCAN tuning and the radio will remain tuned to that station.


AHA0040


Station memory operations Six stations can be set for each band.


1. Tune to the desired station.


2. Push the desired select button for more


3-13


Z 01.2.1/A32-D X


than 2 seconds. (For example, in the dia- gram ch2 is to be memorized. The radio mutes when the select button is pushed.) 3. The indicator “ch2” will then come on and the sound will resume. Memorizing is now complete.


4. Other buttons can be set


manner.


in the same


If the battery cable is disconnected, or if the fuse blows, the radio memory will be can- celled. In that case, reset the desired stations.


Cassette tape operation Turn the ignition key to “ACC” or “ON”, then carefully insert the cassette tape into the tape door.


The cassette tape will automatically pull into the player.


Do not force the cassette tape into the tape door.


HA1078


This could cause player damage.


Adjusting tone quality Push then turn the BASS and TREB (TREBLE) control knob to obtain the most pleasant sound. Adjusting speaker sound balance Push then pull the BAL (BALANCE) control knob to adjust the volume between the right and left speakers. FADER volume control Push then pull the FADER control knob to adjust the volume between the front and rear speakers.


3-14


The cassette tape will automatically change directions to play the other side when the first side is completed. I To maintain good quality sound, NIS- SAN recommends that you use cassette tapes of 60 minutes or shorter in length. I Cassette tapes should be removed from the player when not in use. Store cas- settes in their protective cases and away from direct sunlight, heat, moisture and magnetic sources. Direct sunlight can cause the cassette to become deformed. The use of deformed


Z 01.2.1/A32-D X


cassettes may cause the cassette to jam in the player.


I Do not use cassettes that have labels which are peeling and loose. If used, the label could jam in the player. I If a cassette has loose tape,


insert a pencil through one of the cassette hubs and rewind the tape firmly around the hubs. Loose tape may cause tape jam- ming and wavering sound quality.


I Over a period of


time,


the playback head, capstan and pinch roller may col- lect a tape coating residue as the tape passes over the head. This residue ac- cumulation can cause weak or wavering sound, and should be removed periodi- cally with a head cleaning tape. If the residue is not removed periodically, the player may need to be disassembled for cleaning.


Fast forwarding or rewinding the tape Push either the FF (forward) or REW (rewind) button for the desired direction. The indicator light on the switch will come on. APS fast forwarding or APS rewinding the tape Push either the APS (automatic program search) FF or APS REW button while the cassette tape is playing. The tape will run quickly, and stop and play at the next program. The indicator light flashes on and off while searching the program. This system searches at the blank intervals between selections. If there is a blank interval within one program or there is no interval between programs, the system may not stop in the desired or expected location. Changing the direction of tape play Push the PROG (program) select button.


Playing and stopping the cassette tape Pushing the PLAY/STOP button while the cas- sette tape is playing stops the tape. Pushing the button again plays the tape. Dolby NR (noise reduction) Push the “DOLBY NR” button for Dolby NR encoded tapes to reduce high frequency tape noise. The indicator will come on. Dolby noise reduction manufactured under li- cense from Dolby Laboratories Licensing Cor- poration. “DOLBY” and the double-D symbol are trademarks of Dolby Laboratories


Licensing Corporation. Metal or chrome tape usage The cassette player will be automatically set to high performance play when playing a metal or chrome cassette tape. Ejecting the cassette tape Push the eject button. The cassette tape will automatically come out.


3-15


Z 01.2.1/A32-D X


FM-AM RADIO WITH CASSETTE PLAYER Radio operation Push the POWER/VOLUME control knob to listen to the radio and tune in the desired station.


Push the FM-AM band select button while the cassette tape is playing will turn off the cas- sette player and turn on the radio.


Turn the POWER/VOLUME control knob to adjust the volume.


Inserting a cassette tape into the cassette player while the radio is on will turn off the radio and turn on the cassette player.


The radio has a diversity reception system. The FM signal can reflect off of buildings or mountains. This causes offensive noise. The diversity system employs two antennas; one is a rod type antenna and the other is a printed antenna on the rear window. This system automatically switches to the antenna which receives less noise. Thus the radio provides high quality reception. Selecting the desired band Push the band select button FM-AM band


SAA0233


3-16


Z 01.2.1/A32-D X


select to change the reception as follows: FM1 , FM2 , AM The stereo indicator will glow during FM stereo reception. When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception. Tuning


SEEK tuning ” or Push the SEEK/SCAN tuning button “ “ ” for less than 1.5 seconds. SEEK tun- ing begins and stops at the next broadcasting station.


The radio should not be tuned while driving in order that full attention may be given to the driving operation.


”.


” or “


tuning button


Manual tuning Push down either manual “ SCAN tuning Push the SEEK/SCAN tuning button “ ” or “ ” for more than 1.5 seconds. SCAN tuning begins and stops at each broadcasting station for five seconds. Pushing the button again during this five second period will stop SCAN tuning and the radio will remain tuned to that station.


SAA0234


Twelve stations can be set for the FM band (FM1 and FM2).


Six stations can be set for the AM band.


1. Tune to the desired station using the


SEEK/SCAN or TUNE button.


3-17


Z 01.2.1/A32-D X


2. Push the desired station select button for more than 1.5 seconds. (For example, in the diagram ch2 is to be memorized. The radio mutes when the select button is pushed.)


3. Other buttons can be set


manner.


in the same


If the battery cable is disconnected, or if the fuse blows, the radio memory will be can- celled. In that case, reset the desired stations.


Adjusting tone quality and speaker sound balance Push the AUDIO switch to change the display as follows: BAS , TRE , FAD , BAL BAS (bass) and TRE (treble) adjust the tone quality button “ ” to the most pleasing level. The indicator light will show the level of the tone quality. FAD (fader) adjusts the speaker sound bal- ance between the front ” and rear “ ” speakers, and BAL (balance) adjusts the speaker sound balance between the right


by ” or “


pushing


control


the



SAA0235


” and left “


” speakers by pushing “ the control button. The indicator light will show the level of the speaker sound balance. Cassette tape operation then Turn the ignition key to ACC or ON, carefully insert the cassette tape into the tape door. The cassette tape will automatically pull into the player.


3-18


Z 01.2.1/A32-D X


Do not force the cassette tape into the tape door.


This could cause player damage.


The cassette tape will automatically change directions to play the other side when the first side is completed.


The indicator light will run when the tape is playing. Precautions on cassette player operation I To maintain good quality


sound, NISSAN recommends that you use cas- sette tapes of 60 minutes or shorter in length.


I Cassette tapes should be removed from the player when not in use. Store cas- settes in their protective cases and away from direct sunlight, heat, moisture and magnetic sources. Direct sunlight can cause the cassette to become deformed. The use of deformed cassettes may cause the cassette to jam in the player.


I Do not use cassettes that have labels which are peeling and loose. If used, the label could jam in the player. I If a cassette has loose tape,


insert a pencil through one of the cassette hubs and rewind the tape firmly around the hubs. Loose tape may cause tape jam- ming and wavering sound quality.


I Over a period of


time,


the playback head, capstan and pinch roller may col- lect a tape coating residue as the tape passes over the head. This residue ac- cumulation can cause weak or wavering sound, and should be removed periodi- cally with a head cleaning tape. If the residue is not removed periodically, the player may need to be disassembled for cleaning.


Fast forwarding or rewinding the tape Push either the FF (forward) or REW (rewind) button for the desired direction. The indicator light will run with quick intervals when the FF or REW function is started.


APS fast forwarding or APS rewinding the tape Push either the APS (automatic program search) FF or APS REW button while the cassette tape is playing. The tape will run quickly, and stop and play at the next program. The indicator light will run with quick intervals when the APS FF or APS REW function is started.


This system searches at the blank intervals between selections. If there is a blank interval within one program or there is no interval between programs, the system may not stop in the desired or expected location. Changing the direction of tape play Push the PROG (program) select button. Playing and stopping the cassette tape Pushing the PLAY/STOP button while the cas- sette tape is playing stops the tape. Pushing the button again plays the tape. Dolby NR (noise reduction) Push the DOLBY NR “ ” button for Dolby NR encoded tapes to reduce high frequency tape noise. The indicator will come on.


3-19


Z 01.2.1/A32-D X


Dolby noise reduction manufactured under li- cense from Dolby Laboratories Licensing Cor- poration. “DOLBY” and the double-D symbol are trademarks of Dolby Laboratories


Licensing Corporation. Metal or chrome tape usage The cassette player will be automatically set to high performance play when playing a metal or chrome cassette tape. Ejecting the cassette tape Push the EJECT “ ” button. The cassette tape will automatically come out.


3-20


Z 01.2.1/A32-D X


3-21


SAA0204


Z 01.2.1/A32-D X


To turn the radio off, press the POWER/ VOLUME knob. Turn the POWER/VOLUME control knob to adjust the volume.


FM-AM RADIO WITH CASSETTE PLAYER AND COMPACT DISC PLAYER AUDIO MAIN OPERATION Head unit


The radio has an FM Diversity reception sys- tem, which employs two antennas. One is a rod type antenna; the other is an antenna printed on the window. This system automati- cally switches to the antenna which is receiv- ing less noise.


The tape deck employs a permalloy head which allows for improved reproduction of high frequency ranges. Noise is also greatly re- duced by the combined use of the Dolby NR (noise reduction) system. Power/Volume control Turn the ignition key to “ACC” or “ON”, and then push the POWER/VOLUME knob while the system is off to call up the mode (radio, tape or CD) which was playing immediately before the system was turned off. When no CD or tape is loaded, the radio will come on. While the the POWER/VOLUME knob turns the system off.


pushing


system


on,


is


SAA0194


Adjusting tone quality Push then turn the BASS and TREB (TREBLE) control knobs to obtain the most pleasant sound.


3-22


Z 01.2.1/A32-D X


RADIO OPERATION FM(cid:215) AM band select button


TUNE button


Pushing the FM(cid:215) AM band select button will change the band. When FM(cid:215) AM band select button is pushed while the ignition switch is at “ACC” or “ON”, the radio will come on at the station last played. The last station played will also come on when the power knob is turned to ON. If a compact disc or tape is inserted when the power knob is turned to ON, the compact disc or tape will automatically be turned off and the last radio station played will come on. The FM stereo indicator “ST” will glow during FM stereo reception. When the stereo broad- cast signal is weak, the radio will automatically change from stereo to monaural reception.


The radio should not be tuned while driving in order that full attention may be given to the driving operation.


Use these buttons for manual tuning. If the TUNE button is pushed for less than 0.5
seconds, the frequency moves by an incre- ment of 1 step. To move quickly through the channels, hold either of the TUNE buttons down for more than 0.5 seconds.


SAA0190


Adjusting speaker sound balance Push then pull the BAL (BALANCE) control knob to adjust the volume between the right and left speakers. Fader volume control Push then pull the FADER control knob to adjust the volume between the front and rear speakers.


3-23


Z 01.2.1/A32-D X


SEEK/SCAN tuning buttons


Station memory operations


SEEK tuning Push the SEEK/SCAN tuning button “ ” or “ ” for less than 1.5 seconds. SEEK tun- ing begins from low to high frequencies and stops at the next broadcasting station. SCAN tuning Push the SEEK/SCAN tuning button “ ” or “ ” for more than 1.5 seconds. SCAN tuning begins from low to high frequencies and stops at each broadcasting station for five seconds. Pushing the button again during this five seconds period will stop SCAN tuning and the radio will remain tuned to that station. If the SEEK/SCAN tuning button is not pushed within five seconds, SCAN tuning moves to the next station.


3-24


SAA0191


Z 01.2.1/A32-D X


Twelve stations can be set for the FM band.


Six stations can be set for the AM band.


1. Tune to the desired station using the


SEEK/SCAN or TUNE button.


2. Push the desired station select button for more than 1.5 seconds. (For example, in the diagram ch2 is to be memorized. The radio ceases emitting sounds when the select button is pushed.)


3. The indicator “ch2” will then come on and the sound will resume. Memorizing is now complete.


4. Other buttons can be set


in the same


manner.


If the battery cable is disconnected, or if the fuse blows, the radio memory will be can- celled. In that case, reset the desired stations. CASSETTE TAPE PLAYER OPERATION Turn the ignition key to “ACC” or “ON”, and then lightly insert the cassette tape into the tape door. The cassette tape will be automati- cally pulled into the player.


The radio or CD will turn off (if it is on) and the cassette tape will begin to play.


Do not force the cassette tape into the tape door. This could cause player damage.


If the system is turned off by pushing the POWER/VOLUME knob with the cassette tape still in the player, the tape will resume playing when the system is turned back on. TAPE button I When this button is pushed with the system turned off and a tape loaded, the system will come on and the tape will play.


I When this button is pushed with either the radio or compact disc turned on and the tape loaded, the compact disc or the radio will automatically be turned off and the tape will play.


While the tape is playing, pushing the TAPE button stops the tape. Pushing the button again allows the tape to play. FF (fast forward), REW (rewind) button Push the FF (fast forward) button to fast for- ward the tape. To rewind the tape, push the


3-25


”, “


”, “


REW (rewind) button. Either the indicator light ” will come “ on when the FF or REW function is started. APS (automatic program search) FF, APS REW button


” or “


When the APS FF button is pushed while the tape is being played, the next program will start to play from the beginning. Push the APS FF button several times to skip through pro- grams. The tape will advance the number of times the button is pushed (up to 9 programs). When the APS REW button is pushed once, the program being played starts over from the beginning. Push several times to fast rewind programs. The tape will go back the number of times the button is pushed. Either the indicator light “ ” will come on when the APS FF or APS REW function is started. This system searches for the blank intervals between selections. If there is a blank interval within one program or there is no interval between programs, the system may not stop in the desired or expected location.


” or “


”, “


”,“


Z 01.2.1/A32-D X


PROG (program) button Push the PROG (program) button to change the tape side while the tape is being played.


The cassette tape will automatically change directions to play the other side when the first side is completed. Dolby NR (noise reduction) button “DOLBY NR” button for Dolby Push the NR encoded tapes to reduce high frequency

Loading...
x