1996 Nissan Maxima Owners Manual

switch are “OFF”.

2. Open the fuse box lid.

3. Remove the fuse with the fuse puller.

4. If the fuse is open, replace it with a new

fuse.

Never use a fuse of higher amperage rating than that specified on the fuse box cover.

7-21

Z 01.2.1/A32-D X

FUSIBLE LINKS

LIGHT BULBS

SDI0128

If any electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace only with genuine NISSAN parts.

HEADLIGHTS The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb. A bulb can be replaced from inside the engine compartment without removing the headlight assembly.

High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.

Hold the plastic base when handling the bulb. Never touch the glass envelope.

Removing the headlight bulb 1. Disconnect the battery negative cable.

2. Disconnect

the electrical connector from

the rear end of the bulb.

3. Turn the bulb retaining ring counterclock- wise until it is free from the headlight reflec- tor, then remove it.

4. Remove the headlight bulb. Do not shake

or rotate the bulb when removing it.

SDI0129

7-22

Z 01.2.1/A32-D X

Replacing the headlight bulb 1. Insert the bulb into the headlight reflector with the flat side of the plastic base facing upward.

2. Install the bulb retaining ring and turn it

clockwise until it stops.

3. Push the electrical connector into the bulb

plastic base until it snaps and stops.

DO NOT TOUCH THE BULB. I Use the same number and wattage as

originally installed: Wattage 65/45
Bulb no. 9004

I Aiming is not necessary after replac- ing the bulb. When aiming adjust- ment is necessary, contact your NIS- SAN dealer.

I Do not leave the bulb out of the head- light reflector for a long period of time as dust, moisture, and smoke may enter the headlight body and affect the performance of the headlight.

OTHER LIGHTS

Item

Wattage (W)

Bulb No.

Cornering/clearance

Front turn signal light

Front side marker light

Front fog light

Rear combination light

Turn signal

Stop/Tail

Back-up

Rear side marker light

License plate light

High-mounted stop light

Interior light

Front personal light

Step light

Trunk light

Vanity mirror light

27/8

27

3.8

55

27

27/8

27

3.8

27

10

10

2.7

3.4

1.4

1157

1156

194

1156

1157

1156

194

1156

161

158

—

7-23

Z 01.2.1/A32-D X

MDI0006

Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, first remove the lens and/or cover.

SDI0130

7-24

Z 01.2.1/A32-D X

7-25

SDI0131

Z 01.2.1/A32-D X

7-26

SDI0132

Z 01.2.1/A32-D X

7-27

SDI0133

Z 01.2.1/A32-D X

SDI0333

SDI0134

7-28

Z 01.2.1/A32-D X

WHEELS AND TIRES

DI1033M

If you have a flat tire, see “In case of emergency” section. Maximum inflation pressure Do not exceed the maximum inflation pres- sures shown on the side wall of the tire. Tire inflation pressure Periodically check the tire pressure (including spare). Incorrect tire pressure may adversely affect tire life and vehicle handling. Tire pres- sure should be checked when tires are COLD. Tires are considered COLD after the vehicle has been parked for three or more hours, or driven less than 1 mile (1.6 km). COLD tire

pressures are shown on the tire placard affixed to the center console lid.

Types of tires

The vehicle capacity weight is indicated on the tire placard. Do not load your vehicle beyond this capacity. Overload- ing your vehicle may result in reduced tire life, unsafe operating conditions due to premature tire failure, or unfavorable handling characteristics and could also lead to a serious accident. Loading be- yond the specified capacity may also result in failure of other vehicle compo- nents. Before taking a long trip, or whenever you have loaded your vehicle heavily, use a tire pressure gauge to ensure that the tire pressure is at the specified level. Do not drive your vehicle over 85 MPH (140 km/h) unless it is equipped with high speed capability tires. Driving faster than 85 MPH (140 km/h) may re- sult in tire failure, loss of control and possible injury.

When changing or replacing tires, be sure all four tires are of the same type (i.e., Summer, All Season or Snow) and construction. Your NISSAN dealer may be able to help you with information about tire type, size, speed rating and availability. Replacement tires may have a lower speed rating than the factory equipped tires, and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire.

All season tires NISSAN specifies All Season tires on some models to provide good performance for use all year around, including snowy and icy road conditions. All Season Tires are identified by “ALL SEASON” and/or “M&S” on the tire side- wall. Snow tires have better snow traction than All Season tires and may be more appropriate in some areas.

7-29

Z 01.2.1/A32-D X

poorer than that of non-studded snow tires. Tire chains Use of tire chains may be prohibited according to location. Check the local laws before install- ing tire chains. When installing tire chains, make sure they are of proper size for the tires on your vehicle and are installed according to the chain manufacturer’s suggestions. Use chain tensioners when recommended by the tire chain manufacturer to ensure a tight fit. Loose end links of the tire chain must be secured or removed to prevent the possibility of whipping action damage to the fenders or undercarriage. In addition, drive at a reduced speed. Otherwise, your vehicle may be dam- aged and/or vehicle handling and performance may be adversely affected. Never install tire chains on a T-type spare tire. Do not use the chains on dry roads.

Summer tires

NISSAN specifies summer tires on some mod- els to provide superior performance on dry roads. Summer tire performance in snow and ice will be substantially reduced. Summer tires do not have the tire traction rating “M&S” on the tire sidewall. If you plan to operate your vehicle in snowy or icy conditions, NISSAN recommends the use of “SNOW” or “ALL SEASON” tires on all four wheels. Snow tires If snow tires are needed, it is necessary to select tires equivalent in size and load rating to the original equipment tires. If you do not, it can adversely affect the safety and handling of your vehicle. Generally, snow tires will have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire. For additional traction on icy roads, studded tires may be used. However, some provinces and states prohibit their use. Check local, state and provincial laws before installing studded tires. Skid and traction capabilities of studded snow tires, on wet or dry surfaces, may be

DI1127MA

Tire rotation NISSAN recommends that every 7,500 miles (12,000 km).

tires be rotated

Wheel nut tightening torque:

72 to 87 ft-lb (98 to 118 )

See “Flat tire” in the “In case of emergency” section for tire replacing procedures.

7-30

Z 01.2.1/A32-D X

I After rotating the tires, adjust the tire

pressure.

I Retighten the wheel nuts after the aluminum wheels have been run for the first 600 miles (1,000 km) (also in cases of a flat tire, etc.).

I Do not include the T-type spare tire or any other small size spare tire in the tire rotation.

Tire wear and damage

MDI0004

Tires should be periodically inspected for wear, cracking, bulging, or objects caught in the tread. If excessive wear, cracks, bulging, or deep cuts are found, the tire should be replaced.

The original tires have a built-in tread wear indicator. When the wear indicator is visible, the tire should be replaced.

Improper service for a T-type spare tire

7-31

may result in serious personal injury. If it is necessary to repair the T-type spare tire, contact your NISSAN dealer.

Changing tires and wheels When replacing a tire, use the same size, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in “Wheels and tires” in the “Technical information” section. The use of tires other than those recommended or the mixed use of tires of different brands, con- struction (bias, bias-belted or radial), or tread patterns can adversely affect the ride, braking, handling, ground clearance, body-to-tire clear- ance, snow chain clearance, speedometer calibration, headlight aim and bumper height. Some of these effects may lead to acci- dents and could result in serious personal injury. If the wheels are changed for any reason, always replace with wheels which have the same offset dimension. Wheels of a different offset could cause early tire wear, possibly degraded vehicle handling characteristics and/or brake discs/drums. Such interference can lead to decreased braking efficiency and/or early brake pad/shoe wear.

interference

with

the

Z 01.2.1/A32-D X

Do not install a deformed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warning.

Wheel balance Unbalanced wheels may affect vehicle han- dling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as required.

Wheel balance service should be performed with the wheels off the vehicle. Spin balancing the front wheels on the vehicle could lead to transmission damage. Care of wheels I Wash the wheels when washing the vehicle

to maintain their appearance.

I Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed.

I Do not use abrasive cleaners when wash-

ing the wheels.

I Inspect wheel rims regularly for dents or

corrosion. Such damage may cause loss of pressure or poor seal at the tire bead.

I NISSAN recommends that the road wheels be waxed to protect against road salt in areas where it is used during winter.

Spare tire (T-type spare tire) Observe the following precautions if the T-type spare tire must be used, otherwise your ve- hicle could be damaged or involved in an accident.

I The T-type spare tire should be used only for emergency. It should be re- placed by the standard tire at the first opportunity.

I Drive carefully while the T-type spare

tire is installed.

Avoid sharp turns and abrupt braking while driving.

I Periodically check tire inflation pres- sure, and always keep it at 60 psi (420
kPa, 4.2 bar).

I Do not drive your vehicle at speeds

faster than 50 MPH (80 km/h).

7-32

I Do not use tire chains on a T-type spare tire. Tire chains will not fit prop- erly on the T-type spare tire and may cause damage to the vehicle.

I When driving on roads covered with snow or ice, the T-type spare tire should be used on the rear wheel and the original tire used on the front wheels (drive wheels). Use tire chains only on the front two original tires.

I Tire tread of the T-type spare tire will wear at a faster rate than the original tire. Replace the T-type spare tire as soon as the tread wear indicators appear.

I Because the T-type spare tire is smaller than the original tire, ground clearance is reduced. To avoid dam- age to the vehicle do not drive over obstacles. Also do not drive the ve- hicle through an automatic car wash since it may get caught.

I Do not use the T-type spare tire on

other vehicles.

I Do not use more than one T-type

Z 01.2.1/A32-D X

spare tire at the same time.

7-33

Z 01.2.1/A32-D X

MEMO

7-34

Z 01.2.1/A32-D X

8 Maintenance schedule

General maintenance................................................ 8-3
Periodic maintenance................................................ 8-5

Z 01.2.1/A32-D X

However, under severe driving conditions, ad- ditional or more frequent maintenance will be required. Where to go for service If maintenance service is required or your vehicle appears to malfunction, have the sys- tems checked and tuned by an authorized NISSAN dealer. NISSAN technicians are well-trained special- ists and are kept up to date with the latest service information through technical bulletins, service tips, and in-dealership training pro- grams. They are completely qualified to work on NISSAN’s vehicles before they work on your vehicle, they have worked on it. You can be confident that your NISSAN deal- er’s service department performs the best job to meet the maintenance requirements on your vehicle — in a reliable and economic way.

than after

rather

Your new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money. However, some day-to-day and regular maintenance is essential to maintain your NISSAN’s good mechanical condition, as well as its emission and engine performance.

It is the owner’s responsibility to make sure that the specified maintenance, as well as general maintenance, is performed. As the vehicle owner, you are the only one who can ensure that your vehicle receives the proper maintenance care. You are a vital link in the maintenance chain. General maintenance General maintenance includes those items which should be checked during normal day- to-day operation of the vehicle. They are es- sential if your vehicle is to continue to operate properly. It is your responsibility to perform these procedures regularly as prescribed. These checks or inspections can be done by yourself, a qualified technician or, if you prefer, your NISSAN dealer. Periodic maintenance The maintenance items listed in this part are required to be serviced at regular intervals.

8-2

Z 01.2.1/A32-D X

GENERAL MAINTENANCE

During the normal day-to-day operation of the vehicle, general maintenance should be per- formed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smell, be sure to check for the cause or have your NISSAN dealer do it promptly. In addition, you should notify your NISSAN dealer if you think that repairs are required.

When performing any checks or maintenance work, closely observe the precautions in the “Do-it-yourself operations” section. Additional information on the following items with “*” is found in the “Do-it- yourself operations” section. OUTSIDE THE VEHICLE The maintenance items listed here should be performed from time to time, unless otherwise specified. Tires* Check the pressure with a gauge peri- odically when at a service station, including the spare, and adjust to the specified pressure if necessary. Check carefully for damage, cuts or excessive wear. Wheel nuts* When checking the tires, make sure no nuts are missing, and check for any loose nuts. Tighten if necessary. Tire rotation* Tires should be rotated every

7,500 miles (12,000 km). Wheel alignment and balance If the vehicle pulls to either side while driving on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for wheel alignment. If the steering wheel or seat vibrates at normal highway speeds, wheel balancing may be needed. Windshield wiper blades* Check for cracks or wear if they do not wipe properly. Doors and engine hood Check that all doors and the engine hood operate smoothly as well as the trunk lid or back hatch. Also make sure that all latches lock securely. Lubricate if nec- essary. Make sure that the secondary latch keeps the hood from opening when the pri- mary latch is released. When driving in areas using road salt or other corrosive materials, check lubrication fre- quently.

INSIDE THE VEHICLE The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the vehicle, etc. Lights* Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Warning lights and buzzers/chimes Make sure that all warning lights and buzzers/chimes are operating properly. Windshield wiper and washer* Check that the wipers and washer operate properly and that the wipers do not streak. Windshield defroster Check that the air comes out of the defroster outlets properly and in good quantity when operating the heater or air conditioner. Steering wheel Check that it has the specified play. Be sure to check for changes in the steering conditions, such as excessive play, hard steering or strange noises. Seats Check seat position controls such as seat adjusters, seatback recliner, etc. to make sure they operate smoothly and that all latches lock securely in every position. Check that the

8-3

Z 01.2.1/A32-D X

head restraints move up and down smoothly and that the locks (if equipped) hold securely in all latched positions. Seat belts Check that all parts of the seat belt system (e.g. buckles, anchors, adjusters and retractors) operate properly and smoothly, and are installed securely. Check the belt webbing for cuts, fraying, wear or damage. Accelerator pedal Check the pedal for smooth operation and make sure the pedal does not catch or require uneven effort. Keep the floor mats away from the pedal. Clutch pedal* Make sure the pedal operates smoothly and check that it has the proper free play. Brakes Check that the brakes do not pull the vehicle to one side when applied. Brake pedal and booster* Check the pedal for smooth operation and make sure it has the proper distance under it when depressed fully. Check the brake booster function. Be sure to keep floor mats away from the pedal. Parking brake* Check that the lever has the proper travel and make sure that the vehicle is held securely on a fairly steep hill when only the parking brake is applied. Automatic transaxle “Park” mechanism

Check that the brake pedal must be depressed for the selector lever to be moved from the “P” position. On a fairly steep hill check that the vehicle is held securely with the selector lever in the “P” position without applying any brakes. UNDER THE HOOD AND VEHICLE The maintenance items listed here should be checked periodically (e.g. each time you check the engine oil or refuel). Windshield washer fluid* Check that there is adequate fluid in the tank. Engine coolant level* Check the coolant level when the engine is cold. Radiator and hoses Check the front of the radiator and clean off any dirt, insects, leaves, etc., that may have accumulated. Make sure the hoses have no cracks, deformation, dete- rioration or loose connections. Brake and clutch fluid levels* Make sure that the brake and clutch fluid levels are between the “MAX” and “MIN” lines on the reservoir. Battery* Check the fluid level in each cell. It should be between the “MAX” and “MIN” lines. Engine drive belts* Make sure that no belt is frayed, worn, cracked or oily. Engine oil

level* Check the level on the

8-4

dipstick after parking the vehicle on a level spot and turning off the engine. Be sure to wait a few minutes to allow the oil to drain back into the sump. Power steering fluid level* and lines Check the level in the reservoir tank with the engine off. Check the lines for proper attachment, leaks, cracks, etc. Automatic transaxle fluid level* Check the level on the dipstick after putting the selector lever in “P” with the engine idling. Exhaust system Make sure there are no loose supports, cracks or holes. If the sound of the exhaust seems unusual or there is a smell of exhaust immediately locate the trouble and correct it. (See the carbon monox- ide warning in the “Starting and driving” sec- tion) Underbody The underbody is frequently ex- posed to corrosive substances such as those used on icy roads or to control dust. It is very important to remove these substances, other- wise rust will form on the floor pan, frame, fuel lines and around the exhaust system. At the end of winter, the underbody should be thor- oughly flushed with plain water, being careful to clean those areas where mud and dirt may accumulate. See the “Appearance and interior care” section for additional information.

fumes,

Z 01.2.1/A32-D X

Fluid leaks Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been parked for a while. Water dripping from the air conditioner after use is normal. If you should notice any leaks or if gasoline fumes are evident, check for the cause and have it corrected immediately.

I Driving in dusty conditions. I Driving on rough, muddy, or salt spread

roads.

I Towing a trailer, using a camper or a

car-top carrier. SCHEDULE 2
Follow Periodic Maintenance Schedule 2 if none of the driving conditions shown in Sched- ule 1 apply to your driving habits.

PERIODIC MAINTENANCE

To ensure smooth, trouble-free, safe and eco- nomical driving, NISSAN provides two differ- ent maintenance schedules that may be used, depending upon the conditions in which you usually drive. These schedules contain both distance and time intervals, up to 60,000 miles (96,000 km)/48 months. For most people, the odometer reading will indicate when service is needed. However, if you drive very little, your vehicle should be serviced at the regular time intervals shown in the schedule. After 60,000
miles (96,000 km) or 48 months, continue the periodic maintenance at the same mileage/time intervals. SCHEDULE 1
Follow Periodic Maintenance Schedule 1 if your driving habits frequently include one or more of the following driving conditions: I Repeated short trips of less than 5 miles

(8 km).

I Repeated short trips of less than 10
miles (16 km) with outside temperatures remaining below freezing.

I Operating in hot weather in stop-and-go

“rush hour” traffic.

I Extensive idling and/or low speed driv- ing for long distances, such as police, taxi or door-to-door delivery use.

8-5

Z 01.2.1/A32-D X

SCHEDULE 1
Abbreviations: R = Replace I = Inspect. Correct or replace if necessary.

]: At the mileage intervals only

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Perform at number of miles, kilometers or months, which- ever comes first.

Miles x 1,000
(km x 1,000) Months

3.75
(6)

7.5
(12)

11.25
(18)

15
(24) 12

18.75 22.5 26.25
(42) (30) 15
21

(36) 18

30
(48) 24

33.75 37.5 41.25
(66) (54) 27
33

(60) 30

45
(72) 36

48.75 52.5 56.25
(90) (78) 39
45

(84) 42

60
(96) 48

See NOTE (1) See NOTE (2)

Emission control system maintenance Drive belts Air cleaner filter Vapor lines Fuel lines Fuel filter Engine coolant Engine oil Engine oil filter (Use part No. 15208-31U00 or equivalent) Spark plugs (Use PLATINUM-TIPPED type) Intake & exhaust valve clearance

See NOTE (3)* See NOTE (4)

See NOTE (5)

[R] I* I*

I* [R] I* I*

R* [R]

NOTE: (1) After 60,000 miles (96,000 km) or 48 months, inspect every 15,000 miles (24,000 km) or 12 months.

(2) If operating mainly in dusty conditions, more frequent maintenance may be required. (3) If vehicle is operated under extremely adverse weather conditions or in areas where ambient temperatures are either

extremely low or extremely high, the filters might become clogged. In such an event, replace them immediately.

(4) After 60,000 miles (96,000 km) or 48 months, replace every 30,000 miles (48,000 km) or 24 months. (5) If valve noise increases, inspect valve clearance. (6) Maintenance items and intervals with “*” are recommended by NISSAN for reliable vehicle operation. The owner need not perform such maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are required.

8-6

Z 01.2.1/A32-D X

Abbreviations: I = Inspect. Correct or replace if necessary.

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Miles x 1,000

3.75

7.5 11.25

15 18.75 22.5 26.25

30 33.75 37.5 41.25

45 48.75 52.5 56.25

60

(km x 1,000)

(6)

(12)

(18)

(24)

(30)

(36)

(42)

(48)

(54)

(60)

(66)

(72)

(78)

(84)

(90)

(96)

Months

12

15

18

21

24

27

30

33

36

39

42

45

48

Perform at number of miles, kilometers or months, whichever comes first.

Chassis and body maintenance

Brake lines & cables

Brake pads, discs, drums & linings

Manual & automatic transaxle oil

See NOTE (1).

Steering gear & linkage, axle & suspension parts

Steering linkage ball joints & front suspension ball joints

Exhaust system

Front drive shaft boots

Air bag system

See NOTE (2).

NOTE: (1) If towing a trailer, using a camper or a car-top carrier, or driving on rough or muddy roads, change (not just inspect) oil at

every 30,000 miles (48,000 km) or 24 months.

(2) Inspect the air bag system 10 years after the date of manufacture noted on the FMVSS certification label.

8-7

Z 01.2.1/A32-D X

SCHEDULE 2
Abbreviations: R = Replace I = Inspect. Correct or replace if necessary.

MAINTENANCE OPERATION

Perform at number of miles, kilometers or months, whichever comes first.

Miles x 1,000
(km x 1,000) Months

7.5
(12)

15
(24) 12

22.5
(36) 18

Emission control system maintenance Drive belts See NOTE (1) Air cleaner filter Vapor lines Fuel lines Fuel filter Engine coolant Engine oil Engine oil filter (Use part No. 15208-31U00 or equivalent) Spark plugs (Use PLATINUM-TIPPED type) Intake & exhaust valve clearance

See NOTE (2)* See NOTE (3)

See NOTE (4)

MAINTENANCE INTERVAL

]: At the mileage intervals only

30
(48) 24

[R] I* I*

37.5
(60) 30

45
(72) 36

52.5
(84) 42

60
(96) 48

I* [R] I* I*

R* [R]

NOTE: (1) After 60,000 miles (96,000 km) or 48 months, inspect every 15,000 miles (24,000 km) or 12 months.

(2) If vehicle is operated under extremely adverse weather conditions or in areas where ambient temperatures are either

extremely low or extremely high, the filters might become clogged. In such an event, replace them immediately.

(3) After 60,000 miles (96,000 km) or 48 months, replace every 30,000 miles (48,000 km) or 24 months. (4) If valve noise increases, inspect valve clearance. (5) Maintenance items and intervals with “*” are recommended by NISSAN for reliable vehicle operation. The owner need not perform such maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are required.

8-8

Z 01.2.1/A32-D X

Abbreviations: I = Inspect. Correct or replace if necessary.

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Perform at number of miles, kilometers or months, whichever comes first.

Chassis and body maintenance Brake lines & cables

Brake pads, discs, drums & linings

Manual & automatic transaxle oil

Steering gear linkage, axle & suspension parts

Exhaust system

Front drive shaft boots

Air bag system

Miles x 1,000

(km x 1,000)

Months

7.5

(12)

15

(24)

12

22.5

(36)

18

30

(48)

24

37.5

(60)

30

45

(72)

36

52.5

(84)

42

60

(96)

48

See NOTE (1).

NOTE: (1) Inspect the air bag system 10 years after the date of manufacture noted on the FMVSS certification label.

8-9

Z 01.2.1/A32-D X

EXPLANATION OF MAINTENANCE ITEMS Additional information on the following items with “*” is found in the “Do-it- yourself operations” section. Emission control system maintenance Drive belts* Check drive belts for wear, fray- ing or cracking and also for proper tension. Replace the drive belts if found damaged. Air cleaner filter Under normal driving condi- tions, the air cleaner filter should be replaced in accordance with the maintenance schedule. However, driving the vehicle in dusty areas may cause more rapid clogging of the element. Consequently, the element may have to be replaced more frequently. Vapor lines Check vapor lines and connec- tions for failure or looseness. leaks are found, replace them. Fuel lines Check the fuel hoses, piping and connections for leaks, looseness or deteriora- tion. Replace any parts if they are damaged. Fuel filter If the vehicle is operated under extremely adverse weather conditions or in areas where ambient temperatures are either extremely low or extremely high, the filter

If

In such an event,

might become clogged. replace the filter immediately. Engine coolant* Drain and flush the cooling system. Engine oil & oil filter* Under normal driving conditions, the engine oil and oil filter should be replaced in accordance with the mainte- nance schedule. However, under severe driv- ing conditions, they may have to be replaced more frequently. Spark plugs* Replace with new plugs having the correct heat range. Intake & exhaust valve clearance Check and adjust the valve clearance. Chassis and body maintenance Brake lines & cables Check the brake lines and hoses (including brake booster vacuum hoses, connections & check valve) and park- ing brake cables for proper attachment, leaks, cracks, chafing, abrasion, deterioration, etc. Brake pads, discs, drums & linings Check these and the other neighboring brake compo- nents for wear, deterioration and leaks. Under severe driving conditions, they may have to be inspected more frequently. Manual & automatic transaxle gear oil*

8-10

level and visually inspect for

Check the oil signs of leakage. Under severe driving conditions, the oil should be replaced at the specified interval. Steering gear & linkage, axle & suspension parts, and drive shaft boots Check for dam- age, looseness and leakage of oil or grease. Under severe driving conditions, more fre- quent inspection should be performed. Steering linkage ball joints & front suspen- sion ball joints Check the ball joints for dam- age, looseness and grease leakage. Exhaust system Visually check the exhaust pipes, muffler, and hangers for proper attach- ment, leaks, cracks, chafing, abrasion, dete- rioration, etc. Under severe driving conditions, inspection should be performed more fre- quently. Air bag system Check the air bag system components for proper attachment, damage, deformities, cracks rust, etc. Work around and on the air bag system should be done by an authorized NISSAN dealer.

Z 01.2.1/A32-D X

9 Technical and consumer information

Capacities and recommended fuel/lubricants ............................................................ 9-2
Engine ....................................................................... 9-7
Wheels and tires ....................................................... 9-8
Dimensions and weights ........................................... 9-8
When traveling or registering your vehicle in another country......................................... 9-9
Vehicle identification ................................................. 9-9
Installing license plate............................................. 9-11
Vehicle loading information..................................... 9-12
Trailer towing........................................................... 9-13
Uniform tire quality grading..................................... 9-17
Emission control system warranty .......................... 9-18
Reporting safety defects (For U.S.A.)..................... 9-18

Z 01.2.1/A32-D X

CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure instructed in the “Do-it-yourself operations” section to determine the proper refill capacity.

Fuel

Engine oil (Refill)

With oil filter

Without oil filter

Cooling system

With reservoir Reservoir

Manual transmission gear oil

Automatic transmission fluid

Power steering fluid

Brake and clutch fluid

Capacity (Approximate)

US

Imp

measure

measure

Liter

18-1/2 gal

15-3/8 gal

70

4-1/4 qt

3-7/8 qt

9 qt 7/8 qt —

3-1/2 qt

3-1/4 qt

7-1/2 qt 3/4 qt —

4.0

3.7

8.5
0.8
—

Refill to the proper oil level according to the instructions in the “Do-it- yourself operations” section.

Multi-purpose grease Air conditioning system refrigerant

Air conditioning system lubricants

— —

—

— —

—

— —

—

Recommended specifications

Unleaded gasoline with an octane rating of at least 91 AKI (RON 96)

I API SG or SH and Energy Conserving

II*1, *2

I API Certification Mark*1, *2

Anti-freeze coolant (Ethylene glycol base)

API GL-4*3
Nissan Matic “D” (Continental U.S. and Alaska) or Genuine Nissan Automatic Transmission Fluid (Canada).*4
Type DEXRONTMII or equivalent Genuine Nissan Brake Fluid or equiva- lent*3
DOT 3 (US FMVSS No. 116) NLGI No. 2 (Lithium soap base) HFC-134a (R-134a) Nissan A/C System Oil Type S or exact equivalent

*1: For further details, see “Engine oil and oil filter recommendation”. *2: For further details, see “Recommended SAE viscosity number”. *3: For more information regarding suitable fluids, contact a NISSAN dealer. *4: Dexron III/Mercon or equivalent may also be used. Outside the continental United States and Alaska contact a NISSAN dealer for IIE/Mercon

including recommended brand(s) of Dexron III/Mercon

or Dexron

more information regarding suitable fluids, Automatic Transmission Fluid.

FUEL RECOMMENDATION Unleaded premium gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Research octane number 96) If unleaded premium gasoline is not avail- able, unleaded regular gasoline with an octane rating of at least 87 AKI (Research octane number 91) can be used. However, for maximum vehicle perfor- mance, the use of unleaded premium gaso- line is recommended.

Using a fuel other than that specified could adversely affect the emission con- trol devices and systems, and could also affect the warranty coverage.

Under no circumstances should a leaded gasoline be used, since this will damage the three-way catalyst.

Reformulated Gasoline Some fuel suppliers are now producing refor- mulated gasolines. These gasolines are spe- cially designed to reduce vehicle emissions.

9-2

Z 01.2.1/A32-D X

Nissan supports efforts towards cleaner air and suggests that you use reformulated gaso- line when available. Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxygenates such as ethanol, MTBE and methanol with or without advertising their pres- ence. If you use oxygenate-blend gasoline, please take the following precautions as the usage of such fuels may cause vehicle performance problems and/or fuel system damage. I The fuel should be unleaded and have an octane rating no lower than that rec- ommended for unleaded gasoline.

I If an oxygenate-blend, excepting a methanol blend, is used, it should con- tain no more than 10% oxygenate. (MTBE may, however, be added up to 15%.)

I If a methanol blend is used, it should contain no more than 5% methanol (me- thyl alcohol, wood alcohol). It should also contain a suitable amount of appro- priate cosolvents and corrosion inhibi- tors. If not properly formulated with ap- propriate cosolvents and corrosion inhibitors, such methanol blends may

cause fuel system damage and/or ve- hicle performance problems. At this time, sufficient data is not available to ensure that all methanol blends are suit- able for use in Nissan vehicles.

If any undesirable driveability problems such as engine stalling and hard hot starting are experienced after using oxygenate-blend fu- els, immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. Take care not to spill gasoline during refu- eling. Gasoline containing oxygenates can cause paint damage. Aftermarket fuel additives Nissan does not recommend the use of any fuel additives (i.e. fuel injector cleaner, octane booster, intake valve deposit removers, etc.) which are sold commercially. Many of these additives intended for gum, varnish or deposit removal may contain active solvent or similar ingredients that can be harmful to the fuel system and engine. Octane rating tips In most parts of North America, you should use unleaded gasoline with an octane rating of at least 87 or 91 AKI (Anti-Knock Index) number. However, you may use unleaded gasoline with an octane rating as low as 85 AKI (Anti-Knock

9-3

Index) number in these high altitude areas [over 4,000 ft (1,219 m)] such as: Colorado, Montana, New Mexico, Utah, Wyoming, north- eastern Nevada, southern Idaho, western South Dakota, western Nebraska, and that part of Texas which is directly south of New Mexico. Using unleaded gasoline with an octane rating lower than stated above can cause persistent, heavy “spark knock”. (“Spark knock” is a metallic rapping noise.) If se- vere, this can lead to engine damage. If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating, or if you hear steady spark knock while holding a steady speed on level roads, have your dealer correct the condi- tion. Failure to correct the condition is misuse of the vehicle, for which NISSAN is not responsible. Incorrect ignition timing will result in knocking, after-run or overheating. This in turn may cause excessive fuel consumption or damage to the engine. If any of the above symptoms are encountered, have your vehicle checked at a NISSAN dealer or other competent service facility. However, now and then you may notice light spark knock for a short time while

Z 01.2.1/A32-D X

accelerating or driving up hills. This is no cause for concern, because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load.

ENGINE OIL AND OIL FILTER RECOMMENDATION Selecting the correct oil It is essential to chose the correct quality, and viscosity oil to ensure satisfactory engine life and performance. Nissan recommends the use of a low friction oil (energy conserving oil) in order to improve fuel economy and con- serve energy. Oils which do not have the specified quality label should not be used as they could cause engine damage. Only those engine oils with the American Pe- (API) CERTIFICATION troleum Institute 9-4

STI0077

MARK on the front of the container should be used. This type of oil supersedes the existing API SG or SH and Energy Conserving II categories.

If you cannot find engine oil with the CERTI- FICATION MARK, an API SG or SH and Energy Conserving II oil with API Service Symbol may be used. An oil with a single designation “SG” or “SH”, or in combination with other categories (for example, “SG/CC” or “SG/CD”) may also be used if one with the API CERTIFICATION MARK cannot be found. Mineral based or synthetic type oils may be used in your NISSAN vehicle. These oils must

Z 01.2.1/A32-D X

— repeated short distance driving at cold out-

side temperatures,

— driving in dusty conditions, — extensive idling, — towing a trailer.

however, meet the API quality and SAE vis- cosity ratings specified for your vehicle. Do not mix mineral based and synthetic type oils in the engine at the same time. Oil additives NISSAN does not recommend the use of oil additives. The use of an oil additive is not necessary when the proper oil type is used and maintenance intervals are followed. Oil which may contain foreign matter or has been previously used should not be used. Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is impor- tant that the engine oil viscosity be selected based on the temperatures at which the ve- hicle will be operated before the next oil change. The chart “Recommended SAE vis- cosity number” shows the recommended oil viscosities for the expected ambient tempera- tures. Choosing an oil viscosity other than that recommended could cause serious engine damage.

Selecting the correct oil filter Your new vehicle is equipped with a high- quality genuine Nissan oil filter. When replac- ing, use the genuine oil filter or its equivalent for the reason described in “change intervals”. Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Oil and filter other than the specified quality, or oil and filter change intervals longer than recommended could re- duce engine life. Damage to engines caused by improper maintenance or use of incorrect oil and filter quality and/or viscosity is not covered by the new Nissan vehicle warranties. Your engine was filled with a high quality engine oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle. Op- eration under the following conditions may require more frequent oil and filter changes.

9-5

Z 01.2.1/A32-D X

RECOMMENDED SAE VISCOSITY NUMBER

Air conditioning system refrigerant and lubricant recommendations The air conditioning system in this NISSAN vehicle must be charged with the refriger- ant HFC-134a (R-134a) and the lubricant, Nissan A/C System Oil Type S or the exact equivalents. Use of any other refrigerant or lubricant will cause severe damage and you will need to replace your vehicle’s entire air conditioning system. The new refrigerant HFC-134a (R-134a) in your NISSAN vehicle will not harm the earth’s ozone layer. Although this refrigerant does not affect the earth’s atmosphere, certain govern- mental regulations require the recovery and recycling of any refrigerant during automotive air conditioning system service. Your NISSAN dealer has the trained technicians and equip- ment needed to recover and recycle your air conditioning system refrigerant. Contact your NISSAN dealer when servicing your air conditioning system.

TI1028-B I SAE 5W-30 viscosity oil is preferred for all temperatures. SAE 10W-30 viscosity oil may be used if the ambient tempera- ture is above 0°F (−18°C).

TI1002M I 80W-90 is preferable for ambient tem-

peratures below 104°F (40°C).

9-6

Z 01.2.1/A32-D X

ENGINE

Type Cylinder arrangement Bore x Stroke Displacement Firing order Idle speed Ignition timing (B.T.D.C.) CO percentage at idle speed

Spark plug

Spark plug gap Camshaft operation Alternator belt size Width x Length

Model

in (mm) cu in (cm3)

rpm degree/rpm [No air] % Standard Service option in (mm)

VQ30DE

Gasoline, 4-cycle 6-cylinder, V-slanted at 60° 3.66 x 2.886 (93.0 x 73.3) 182.33 (2,988) 1-2-3-4-5-6*

See the “Emission Control Label” on the underside of the hood.

PFR5G-11
PFR4G-11, PFR6G-11

—

Timing chain

in (mm)

0.8409 x 43.11 (21.36 x 1,095)

The spark ignition system of this vehicle meets all requirements of the Canadian Interference-Causing Equipment Regula- tions.

TI1009-A

9-7

Z 01.2.1/A32-D X

WHEELS AND TIRES

DIMENSIONS AND WEIGHTS

Road wheel

Tire size

Steel

Offset

15 x 6JJ

in (mm) 1.57 (40)

Aluminum

15 x 6.5JJ

Offset

in (mm) 1.77 (45)

Conventional

Spare

P205/65R15 92S P205/65R15 92H P215/60R15 93H

Conventional*1
T125/70D16*2
T125/90D16*2, *3

Overall length

Overall width

Overall height

Front tread

Rear tread

Wheelbase

Sedan

in (mm)

187.7 (4,768)

in (mm)

69.7 (1,770)

in (mm)

55.7 (1,415)

in (mm)

in (mm)

60.2 (1,530)*1
59.8 (1,520)*2

59.4 (1,510)*1
59.1 (1,500)*2

in (mm)

106.3 (2,700)

*1: For CANADA *2: For U.S.A. *3: For models with Viscous LSD

Gross vehicle weight rating

lb (kg)

Gross axle weight rating

Front

Rear

lb (kg)

lb (kg)

*1: For models with steel wheels *2: For models with aluminum wheels

See the “F.M.V.S.S. certifica- tion label” on the driver’s side lock pillar.

9-8

Z 01.2.1/A32-D X

WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY When planning to travel in another country, you should first find out if the fuel available is suitable for your vehicle’s engine. Using fuel with too low an octane/cetane rating may cause engine damage. All gasoline ve- hicles must be operated with unleaded engine gasoline. Therefore, avoid taking your vehicle to areas where appropriate fuel is not avail- able. When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emission control and safety standards vary according to the country, state, province or district; therefore, vehicle specifications may differ. When any vehicle is to be taken into an- other country, state, province or district and registered, its modifications, transpor- tation, and registration are the responsibil- ity of the user. NISSAN is not responsible for any inconvenience that may result.

VEHICLE IDENTIFICATION

STI0038

STI0040

VEHICLE IDENTIFICATION NUMBER PLATE The vehicle identification number plate is at- tached as shown. This number is the identifi- cation for your vehicle and is used in the vehicle registration.

VEHICLE IDENTIFICATION NUMBER (Chassis number) The number is stamped as shown.

9-9

Z 01.2.1/A32-D X

STI0047

STI0041

STI0042

ENGINE SERIAL NUMBER The number is stamped on the engine as shown.

F.M.V.S.S. CERTIFICATION LABEL The F.M.V.S.S. certification label is affixed as shown.

EMISSION CONTROL INFORMATION LABEL The emission control tached as shown.

information label

is at-

9-10

Z 01.2.1/A32-D X

INSTALLING LICENSE PLATE

STI0043

STI0044

TIRE PLACARD The cold tire pressure is shown on the tire placard affixed to the center console lid.

AIR CONDITIONER SPECIFICATION LABEL The label is affixed inside of shown.

the hood as

STI0045

Use the following steps to mount the license plate:

1. Make a hole in each plastic finisher (There are small marks on the bumper) using a 0.31 in (8 mm) drill. To avoid damaging the

9-11

Z 01.2.1/A32-D X

threads behind the finisher, apply only light pressure to the drill.

2. Mount the license plate bracket. 3. Mount the license plate with the 0.24 in (6
mm) bolts. The bolts used to fasten the license plate to the bracket are not included in the attaching hardware that comes with the bracket.

VEHICLE LOADING INFORMATION

I It is extremely dangerous to ride in a cargo area inside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed

I Do not allow people to ride in any is not

area of your vehicle that equipped with seats and seat belts. I Be sure everyone in your vehicle is in a seat and using a seat belt properly.

Terms It is important to familiarize yourself with the following terms before loading your vehicle: I Curb Weight (actual weight of your vehicle) including: standard and - vehicle weight optional equipment, fluids, emergency tools, and spare tire assembly. This weight does not include passengers and cargo. I GVW (Gross Vehicle Weight) - curb weight plus the combined weight of passengers and cargo.

9-12

I GVWR (Gross Vehicle Weight Rating) - maximum total weight (load) limit specified for the vehicle.

I GAWR (Gross Axle Weight Rating) - maxi- mum weight (load) limit specified for the front or rear axle.

Determining vehicle load capacity The load capacity of this vehicle is determined by weight, not by available cargo space. For example, a luggage rack, bike carrier, cartop carrier or similar equipment does not increase load carrying capacity of your vehicle. To determine vehicle load capacity: Vehicle weight can be determined by using a commercial-grade scale, found at places such as a truck stop, gravel quarry, grain elevator, or a scrap metal recycling facility. 1) Determine the curb weight of your vehicle. 2) Compare the curb weight amount to the GVWR specified for your vehicle to deter- mine how much more weight your vehicle can carry.

3) After loading (cargo and passengers), re- weigh your vehicle to determine if either GVWR or GAWR for your vehicle is ex- ceeded. If GVWR is exceeded, remove cargo as necessary. If either the front or

Z 01.2.1/A32-D X

warranty.

rear GAWR is exceeded, shift the load or remove cargo as necessary.

Loading tips I The GVW must not exceed GVWR or GAWR as specified on the FMVSS Certifi- cation Label.

I Do not load the front and rear axle to the GAWR. Doing so will exceed the GVWR.

I Properly secure all cargo to help pre- vent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.

I Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could result in loss of control and cause personal injury.

I Overloading can shorten the life of your vehicle. Failures caused by overloading are not covered by your

TRAILER TOWING

TI1011M

Your new vehicle was designed to be used primarily to carry passengers and cargo. Re- member that towing a trailer will place addi- tional loads on your vehicle’s engine, drive train, steering, braking and other systems. Information on trailer towing ability and the special equipment required should be ob- tained from your Nissan dealer. He can obtain a Nissan Trailer Towing Guide for you.

9-13

Z 01.2.1/A32-D X

Maximum load limits Maximum trailer loads Never allow the total trailer load to exceed 1,000 lb (454 kg). The total trailer load equals trailer weight plus its cargo weight. Towing loads greater than 1,000 lb (454 kg) or using improper towing equipment could adversely affect vehicle handling, braking and perfor- mance.

Vehicle damage and/or personal injury resulting from improper towing proce- dures is not covered by NISSAN warran- ties. Information on trailer towing and required towing equipment should be obtained from dealers who specialize in providing trailers or other towing equipment.

Tongue load Keep the tongue load between 9 and 11% of the total trailer load. If the tongue load be- comes excessive, rearrange cargo to allow for proper tongue load.

TI1012M

shown

(GVWR)

Maximum gross vehicle weight/maximum gross axle weight The gross vehicle weight of the towing vehicle must not exceed the gross vehicle weight rating F.M. V.S.S. certification label. The gross vehicle weight equals the combined weight of the unloaded vehicle, passengers, luggage, hitch, trailer tongue load and any other optional equipment. In addition, front or rear gross axle weight must not exceed the gross axle weight rating (GAWR) shown on the F.M.V.S.S. cer- tification label.

the

on

Towing load/specification chart

Unit: lb (kg)

MAXIMUM TOWING LOAD

MAXIMUM TONGUE LOAD

1,000 (454)

110 (49)

Trailer hitch Choose a proper hitch for your vehicle and trailer. Make sure the trailer hitch is securely attached to the vehicle, to help avoid personal injury or property damage due to sway caused