2000 Nissan Frontier Owners Manual

Controls ..................................................................4-3
Heater operation ....................................................4-4
Air conditioner operation (if so equipped)..............4-5
Air flow charts.........................................................4-6
AM-FM radio with cassette player........................4-10
Cassette tape operation .......................................4-13
FM-AM radio with compact disc (CD) player .......4-15

Compact disc (CD) player operation ....................4-19
AM-FM Radio with cassette player and compact disc player (if so equipped)...................4-21
Cassette tape operation .......................................4-25
Compact disc (CD) player operation ....................4-26
Antenna ................................................................4-28
Car phone or CB radio.........................................4-28

Z X

VENTILATORS

Adjust air flow direction by moving the ven- tilators slides and ventilator assemblies.

AHA1099

4-2 Heater, air conditioner and audio systems

Z X

HEATER AND AIR CONDITIONER

WARNING

I The air conditioner cooling function operates only when the engine is running. I Do not

leave children, unreliable adults, or pets alone in your vehicle. On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or animals.

I Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

I Positioning of the heater and air con- ditioner controls should not be done while driving, in order that full atten- tion may be given to the driving operation.

turns the fan on and off, and

CONTROLS Fan control dial This dial controls fan speed. Air flow control dial This dial allows you to select the air flow outlets.

— Air flows from center and side

ventilators.

— Air flows from center and side

ventilators and foot outlets.

AHA1129

— Air flows mainly from foot outlets. — Air flows from defroster outlets

and foot outlets.

— Air flows mainly from defroster out-

lets.

The air flow control dial also has intermedi- ate positions which allow the air flow to be distributed between two of the icon posi- tions on the air flow control dial. Temperature control dial This dial allows you to adjust the tempera- ture of the outlet air.

Heater, air conditioner and audio systems 4-3

Z X

Air recirculation button (if

so equipped) NOTE: The air recirculation feature is available only on those vehicles equipped with air conditioning. OFF position (indicator light off): Outside air is drawn into the passenger compartment and distributed through the selected outlets. Use the OFF position for normal heater or air conditioner operation. ON position (indicator light on): Interior air is recirculated inside the vehicle. Push the button to the on position when: I driving on a dusty road. I to prevent traffic fumes from entering the

passenger compartment.

I for maximum cooling when using the air

conditioner.

Air conditioner button (if so equipped) Start the engine, move the fan control dial to the desired (one to four) position, and push the air conditioner button to turn on the air conditioner. The indicator light comes on when the air conditioner is operating. To turn off the air conditioner, push the button again. The air conditioner cooling function op- erates only when the engine is running. HEATER OPERATION Heating This mode is used to direct hot air mainly from the floor outlets. A small amount of air also flows from the defrost outlets. 1. Push the

button (if so equipped) to

the off position for normal heating.

2. Turn the air control dial to the

po-

sition.

3. Turn the fan control dial to the desired

position.

4. Turn the temperature control dial to the

4-4 Heater, air conditioner and audio systems

desired position between the middle and the hot position.

Ventilation This mode directs outside air from the side and center vents. 1. Push the

button (if so equipped) to

the off position.

2. Turn the air control dial to the

po-

sition.

3. Turn the fan control dial to the desired

position.

4. Turn the temperature control dial to the

desired position.

Defrosting/defogging This mode is used to defrost/defog the windows. 1. Turn the air control dial to the

po-

sition.

I When the

position is selected, the air conditioner automatically turns on (however, the indicator light will not illu- minate) the outside temperature is more than 45(cid:228)F (7(cid:228)C). This dehumidifies the air which helps defog the windshield.

if

Z X

The mode automatically turns off, allowing outside air to be drawn into the passenger compartment to further im- prove the defogging performance

2. Move the fan control dial to the desired

position.

3. Move the temperature control dial to the desired position between the middle and the hot position. Bi-level heating This mode directs cooler air from the side and center vents and warmer air from the floor outlets. When the temperature control dial is moved to the full hot or full cool position, the air between the vents and the floor outlets is the same temperature. 1. Push the

button (if so equipped) to

the off position.

2. Turn the air control dial to the

po-

sition.

3. Turn the fan control dial to the desired

position.

4. Turn the temperature control dial to the

desired position.

Heating and defrosting/defogging This mode heats the interior and defogs the windshield. 1. Turn the air control dial to the

po-

sition.

I When the

if

position is selected, the air conditioner automatically turns on (however, the indicator light will not illu- minate) the outside temperature is more than 45(cid:228)F (7(cid:228)C). This dehumidifies the air which helps defog the windshield. mode automatically turns off, The allowing outside air to be drawn into the passenger compartment to further im- prove the defogging performance.

2. Turn the fan control dial to the desired

position.

3. Turn the temperature control dial to the desired position between the middle and the hot postion. Operating tips Clear snow and ice from the wiper blades and air inlet in front of the wind- shield. This improves heater operation.

AIR CONDITIONER OPERATION (if so equipped) Start the engine, move the fan control dial to the desired (one to four) position, and push in the air conditioner button to activate the air conditioner. When the air conditioner is on, cooling and dehumidfying functions are added to the heater operation. The air conditioner cooling function op- erates only when the engine is running. Cooling This mode is used to cool and dehumidify the air. 1. Push the 2. Turn the air control dial to the

button to the off position. po-

sition.

3. Turn the fan control dial to the desired

position.

4. Turn on the air conditioner button. The

indicator light comes on.

5. Turn the temperature control dial to the

desired position.

For quick cooling when the outside tem- perature is high, push the button to Heater, air conditioner and audio systems 4-5

Z X

the on position. Be sure to return the air recirculation button to the off position for normal cooling. Dehumidfied heating This mode is used to heat and dehumidfy the air. 1. Push the 2. Turn the air control dial to the

button to the off position. po-

sition.

3. Turn the fan control dial to the desired

position.

4. Turn on the air conditioner button. The

indicator light comes on.

5. Turn the temperature control dial to the

desired position.

Dehumidfied defrosting/defogging This mode is used to defog the windows and dehumidify the air. 1. Turn the air control dial to the

po-

sition.

I When the

or positions in between are selected, the air conditioner automatically turns on (however, the in- dicator light will not the

I If 4-6 Heater, air conditioner and audio systems

illuminate) if

defog

outside temperature is more than 45(cid:228)F (7(cid:228)C). This dehumidifies the air which helps The mode automatically turns off, al- lowing outside air to be drawn into the passenger compartment to further im- prove the defogging performance.

the windshield.

2. Turn the fan control dial to the desired

position.

3. Turn the temperature control dial to the

desired position.

Operating tips I Keep windows and sunroof closed while

the air conditioner is in operation.

I After parking in the sun, drive for two or three minutes with the windows open to vent hot air from the passenger compart- ment. Then, close the windows. This allows the air conditioner to cool the interior more quickly.

I The air conditioning system should be operated for approximately ten min- utes at least once a month. This helps prevent damage to the system due to lack of lubrication.

gauge indicates engine coolant tem- perature over the normal range, turn the air conditioner off. See † If your vehicle overheats† in the † In case of emergency† section of this manual.

AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting. The air recir- culation switch should always be in the OFF position for heating and defrosting. When the or positions in be- tween are selected, the air conditioner au- tomatically turns on (however, the indicator light will not illuminate) if the outside tem- perature is more than 45(cid:228)F (7(cid:228)C). This de- humidifies the air which helps defog the windshield. The mode automatically turns off, allowing outside air to be drawn into the passenger compartment to further improve the defogging performance..

the engine coolant

temperature

Z X

AHA1130

AHA1131

Heater, air conditioner and audio systems 4-7

Z X

4-8 Heater, air conditioner and audio systems

AHA1132

AHA1133

Z X

Servicing air conditioner The air conditioner system in your NISSAN is charged with a refrigerant designed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants causes severe damage to your air conditioner system. See † Air conditioner system refrigerant and lubrication recom- mendations† in the † Technical and con- sumer information† section of this manual. An authorized NISSAN dealer will be able to service your environmentally † friendly† air conditioner system.

WARNING

The air conditioner system contains refrigerant under high pressure. To avoid personal injury, any air condi- tioner service should be done only by an experienced technician with proper equipment.

AHA1134

Heater, air conditioner and audio systems 4-9

Z X

AM-FM RADIO WITH CASSETTE PLAYER This audio system has the FADER function installed in Crew Cab models. Standard and King Cab models, equipped with this audio system, do not have the FADER function. ON(cid:215) OFF/VOL control knob Turn the ignition key to the ACC or ON position, then push the ON(cid:215) OFF/VOL con- trol knob. If you listen to the radio with the engine not running, turn the key to the ACC position. The mode (radio or cassette) which was playing immediately before the system was turned off resumes playing. When no cassette is loaded, the radio comes on. Pushing the ON(cid:215) OFF/VOL con- trol knob again turns the system off. Turn the ON(cid:215) OFF/VOL control knob to ad- just the volume. Clock operation Pressing the CLOCK button alternates the clock and the radio/cassette tape options in the display.

Z X

4-10 Heater, air conditioner and audio systems

AHA1004

buttons together sets minutes.

Clock set Depressing the CLOCK and the buttons together sets hours. Depressing the CLOCK and Clock priority mode In this mode the clock is shown in the display. If any radio or cassette tape func- tions are activated, the radio (or cassette tape) display illuminates for 10 seconds then returns to the clock mode. NOTE: After clock adjustment, the radio is in the clock priority mode. Radio/Cassette tape priority mode In this mode, the radio station illuminates in the display during radio operation. During cassette tape operation, TAPE illuminates in the display. Selecting the desired band Push the to FM1 or FM2 reception. The FM stereo indicator, ST, illuminates dur- ing FM stereo reception. When the stereo broadcast signal is weak, the radio automati-

button to change from AM

influences.

cally changes from stereo to monaural re- ception. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other ex- ternal Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the vehicle may influence radio reception quality. TUNE buttons

WARNING

The radio should not be tuned while driving in order that full attention may be given to the driving operation.

again continues the SEEK function. Once the highest broadcasting station is reached, the radio continues in the SEEK mode at the lowest broadcast station. SCAN tuning Push and hold the

tuning button for more than 1.5 seconds. SCAN illu- minates in the display window. SCAN tuning begins from low to high frequencies and stops at each broadcasting station for five seconds. Pushing the button again during this five second period stops SCAN tuning and the radio remains tuned to that station.

and

Use the buttons for manual tuning. To move quickly through the channels, hold either of the tune buttons down for more than 1.5 seconds. SEEK tuning Push the for less than 1.5 seconds. SEEK tuning begins from low to high frequencies and stops at the next broadcasting station. Pushing the button

tuning button

Heater, air conditioner and audio systems 4-11

Z X

FM2. The selected band illuminates in the display.

2. Tune to the desired station. 3. Push the desired station select button for more than 2 seconds. For example, in the illustrations, ch2 is to be memorized. The radio mutes when the select button is pushed.

4. When the sound resumes, memorizing is

complete.

5. Other station select buttons can be set in

the same manner.

If the battery cable is disconnected, or if the radio fuse opens, the radio memory is can- celled. In that case, reset the desired sta- tions.

AHA1045

Station memory operations Six stations can be set for the AM band. 12
stations can be set for the FM band (six for FM1, six for FM2). 1. Push

to select AM, FM1, or

4-12 Heater, air conditioner and audio systems

AHA1027

Adjusting tone quality and speaker balance To adjust BASS(cid:215) TREB(cid:215) FADER (Crew Cab models only) and BAL (Bass, Treble, Fader, Balance), press the AUDIO button until the desired mode (BAS, TRE, FAD or BAL) appears in the display. Press the button to adjust Bass (BAS) and Treble (TRE) to the desired level. Use the button to adjust Fader (FAD) or Balance modes. Fader adjusts the sound level between the front and rear speakers and Balance (BAL)

or

or

Z X

adjusts the sound level between the right and left speakers. After 10 seconds, the radio or cassette tape display reappears. Once the sound quality is set to the desired level, the AUDIO button can be pressed repeatedly until the radio or cassette tape display appears. CASSETTE TAPE OPERATION Turn the ignition key to ACC or ON and carefully insert a cassette tape into the tape door. The cassette tape automatically pulls into the player. The word TAPE and moving digital squares illuminate on the right side of the display window. If the radio is already operating it automatically turns off and the cassette tape begins to play.

CAUTION

Do not force the cassette tape into the tape door. This could cause player damage.

The cassette tape automatically changes directions to play the other side when the first side is complete. At this time, the mov- ing digital squares illuminate on the left side

of the display window. Precautions on cassette player op- erations I To maintain good quality sound, NIS- SAN recommends using cassette tapes of 60 minutes or shorter in length.

I Cassette tapes should be removed from the player when not in use. Store cassettes in their protective cases and away from direct sunlight, heat, dust, moisture and magnetic sources. I Direct sunlight can cause the cassette to become deformed. The use of de- formed cassettes may cause the cas- sette to jam in the player.

I Do not use cassettes with labels which are peeling and loose. If used, the label could jam in the player.

I If a cassette has loose tape, insert a pencil through one of the cassette hubs and rewind the tape firmly around the hubs. Loose tape may cause tape jamming and wavering sound quality.

I Over a period of time, the playback head, capstan and pinch roller may

collect a tape coating residue as the tape is played. This residue accumu- lation can cause weak or wavering sound, and should be removed peri- odically with a head cleaning tape. If the residue is not removed periodi- cally, the player may need to be disas- sembled for cleaning.

or

or

button for

forwarding or rewinding the

Fast tape Push either the the desired direction. The FF or REW symbol illuminates in the display. To stop the FF or REW function, press the button. Automatic Program Search (APS) fast forwarding or APS rewinding the tape Push either the button while the cassette tape is playing. The tape runs quickly, stops, then plays the next selection from the beginning. Either the FF or REW symbol flashes in the display while searching for the selection.

again, or the

or

Heater, air conditioner and audio systems 4-13

Z X

Dolby NR is manufactured under license from Dolby Laboratories Licensing Corpora- tion. DOLBY NR and the double-D symbol are trademarks of Dolby Laboratories Li- censing Corporation. Metal or chrome tape usage The cassette player is automatically set to high performance play when playing a metal or chrome cassette tape. Ejecting the cassette tape Push the cassette tape.

button to eject an inserted

This system searches for the blank intervals between selections. If there is a blank inter- val within one selection or there is no inter- val between selections, the system may not stop in the desired or expected location. Changing the direction of tape play Push the (program) select button. The moving digital squares illuminate on either the right or left side of the display window to indicate the side of program play. Playing and stopping the cassette tape Push the button while the cassette tape is playing to stop the tape. Push the button again to play the tape. Dolby NR (noise reduction) Push the button for Dolby NR en- coded tapes to reduce high frequency tape noise. The illuminates in the display. If the display is in the clock priority mode when pressed, and TAPE illuminate in the display window for about 10 seconds. The clock mode then returns to the display window. 4-14 Heater, air conditioner and audio systems

symbol

button

the

is

Z X

AUDIO SYSTEM

LHA0002

influences.

FM-AM RADIO WITH COMPACT DISC (CD) PLAYER Audio main operation To turn the radio on, turn the ignition key to ACC or ON. If you listen to the radio with the engine not running, turn the key to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other ex- ternal Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the vehicle may influence radio reception quality. Power/Volume control Turn the ignition key to the ACC or ON, then push the power/volume control knob. The mode (radio or CD) which was playing im- mediately before the system was turned off resumes playing. When no CD is loaded, the the power/volume control knob again turns the system off.

on. Pushing

comes

radio

Heater, air conditioner and audio systems 4-15

Z X

After 10 seconds, the radio or CD display will reappear. Once the sound quality is set knob to the desired level, press the repeatedly until the radio or CD display reappears.

Turn the power/volume control knob to ad- just the volume. Adjusting tone quality and speaker balance. To adjust Bass, Treble, Fader (Crew Cab models only) or Balance, press the knob for less than 1.5 seconds. A beep signals entry into the audio adjustment mode and BASS will appear in the display. knob to adjust Bass Rotate the (BASS) to the desired level. Press the knob a second time and TREB appears in the display. Rotate the knob to adjust Treble (TREB) to the

desired level. knob a third time and FAD Press the appears in the display (Crew Cab models only). Fader (FAD) adjusts the sound be- tween the front and rear speakers. Rotate the knob to adjust Fader (FAD) to the desired level. Press the knob a fourth time and BAL appears in the display. Balance (BAL) ad- justs the sound between the right and left knob to adjust speakers. Rotate the Balance (BAL) to the desired level. 4-16 Heater, air conditioner and audio systems

Z X

Clock operation The clock is on in the display regardless of what mode, media, or function the radio is in as long as the ignition is in ACC or ON. Clock set To adjust the clock, press the knob for longer than 1.5 seconds. A beep signals entry into the clock adjustment mode and CL appears in the display. The hours will be knob to adjust blinking. Rotate the the hours to the desired level. Press the knob a second time and the minutes will start to blink. Rotate the the minutes to the

knob to adjust

desired level. After 10 seconds, the radio or CD display will reappear. Once the clock is set to the knob repeat- desired level, press the edly until the radio or CD display reappears.

LHA0025

Heater, air conditioner and audio systems 4-17

Z X

Knob

WARNING

The radio should not be tuned while driving in order that full attention may be given to the driving operation.

Rotate the left for manual tuning.

knob to the right or to the

SEEK/SCAN tuning

SEEK tuning Push the SEEK/SCAN tuning button

or for less than 1.5 seconds. SEEK tuning begins from high to low frequencies or low to high frequencies, depending on which but- ton is pressed, and stops at the next broad- casting station. Once the highest broadcast- ing station is reached, the radio continues in the SEEK mode at the lowest broadcasting button once the station. lowest broadcasting station is reached, the radio continues in the SEEK mode at the highest broadcasting station.

If using the

Z X

FM/AM radio operation FM/AM band select Push the band select button (FM/AM) to change from AM to FM1 or FM2 reception. The FM stereo indicator, ST, illuminates 4-18 Heater, air conditioner and audio systems

during FM stereo reception. When the ste- reo broadcast signal the radio automatically changes from stereo to mon- aural reception.

is weak,

LHA0026

SCAN tuning Push the SEEK/SCAN tuning button

or for more than 1.5 seconds. SCAN ap- pearsin the display window. SCAN tuning begins from high to low frequencies or low to high frequencies, depending on which but- ton is pressed. SCAN tuning stops at each broadcasting station for five seconds. Push- ing the button again during this five second period stops SCAN tuning and the radio remains tuned to that station. Station memory operations Six stations can be set for the AM band. 12
stations can be set for the FM band (six for FM1, six for FM2). 1. Push the band select button (FM/AM) to select AM, FM1, or FM2. The selected band illuminates in the display.

2. Tune to the desired station. 3. Push the desired station select button for more than 1.5 seconds. The radio mutes when the select button is pushed.

4. The indicator, ch2, then illuminates in the display and the sound resumes. Memo- rizing is now complete. display and the sound resumes, memorizing is complete.

5. Other station select buttons can be set in

the same manner.

If the battery cable is disconnected, or if the radio fuse opens, the radio memory is can- celled. In that case, reset the desired stations. COMPACT DISC (CD) player op- eration Turn the ignition key to the ACC or ON position and carefully insert the compact disc into the slot with the label side up. The compact disc is automatically pulled into the slot and starts to play. If the radio is already operating, it automati- cally turns off and the compact disc begins to play.

CAUTION

Do not force the compact disc into the slot. This could damage the player.

CD button When this button is pushed with the com- pact disc loaded and the radio playing, the radio turns off and compact disc starts to play.

or

FF (Fast forward) REW (Rewind) When the button is pushed while the compact disc is playing, the com- pact disc plays at an increased speed while fast forwarding or rewinding. When the but- ton is released, the compact disc returns to normal play speed.

APS (Automatic Program Search) FF, APS REW When the compact disc is playing, the selection fol-

button is pushed while the

Heater, air conditioner and audio systems 4-19

Z X

lowing the present one starts to play from but- the beginning. Push or hold the ton several times to skip several selections. Each time the button is pushed, the CD advances one selection. (When the last selection on the compact disc is skipped, the first selection is played.) When the button is pushed, the se- lection being played returns to the begin- ning. Push or hold the button several times to skip back several selections. Each time the button is pushed, the CD moves back one selection.

RPT (Repeat)

When the repeat button is pushed while the compact disc is playing, the play pattern changes as follows. 1: The current selection is repeated. MIX: Selections are played at random, not following the sequence on the compact disc. The same program may be repeated twice. Normal (no symbol): All selections are played in sequence, and the compact disc stops when the last selection is finished.

When a new compact disc is inserted, the play pattern automatically changes to the † Normal† play pattern.

CD EJECT

When the button is pushed with a com- pact disc loaded, the compact disc ejects. When the button is pushed while the compact disc is playing, the compact disc ejects and the system turns off. If the compact disc ejects and is not removed within 10 seconds, it is pulled back into the slot. DISC indicator light CD IN appears on the display when a CD is loaded with the system ON

CAUTION

I During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely.

I The player may skip while driving on

rough roads.

I The CD player sometimes cannot function when the passenger com- partment temperature is extremely high. Decrease the temperature be- fore use.

I Do not expose the CD to direct sun-

light.

I Do not touch the playing surface of

the disc.

I Do not use 8cm discs. They may cause player damage even if using with the optional adapter.

I Recordable compact discs (CD-R) may not function properly in the CD player.

4-20 Heater, air conditioner and audio systems

Z X

AM-FM RADIO WITH CASSETTE PLAYER AND COMPACT DISC PLAYER (if so equipped) ON(cid:215) OFF/VOL control knob Turn the ignition key to the ACC or ON position, then push the ON(cid:215) OFF/VOL con- trol knob button. If you listen to the radio with the engine not running, turn the key to the ACC position. The mode (radio, tape or CD) which was playing immediately before the system was turned off resumes playing. When no CD or tape is loaded, the radio comes on. Push the ON(cid:215) OFF/VOL control knob button again turns the system off. Turn the ON(cid:215) OFF/VOL control knob to ad- just the volume. Clock operation Pressing the clock button displays the clock. Clock set Press the CLOCK button for more than 2
seconds the radio beeps and the hours flash,

TUNE/FF-REW

use

the

AHA1112

buttons to set

the hour, press the CLOCK button again until the radio beeps Heater, air conditioner and audio systems 4-21

Z X

buttons to set

button to change from AM to

and minutes flash, use the TUNE/FF-REW the minutes. The display will return to regular clock dis- play in 7 seconds or you may press the CLOCK button again to return to the regular clock display. FM-AM band select button Push the FM1 or FM2 reception. The FM stereo indicator, ST, illuminates during FM stereo reception. When the ste- reo broadcast signal the radio automatically changes from stereo to mon- aural reception. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains, and other external influences. Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the vehicle may influence radio reception quality.

is weak,

or

SCAN tuning Push and hold the SEEK/SCAN tuning but- for more than 1.5 seconds. ton SCAN illuminates in the display window, and the radio station blinks. SCAN tuning begins from low to high frequencies or from high to low frequencies, depending on which button is pressed. Scan tuning stops at each broadcasting station for five sec- onds. When scanning, SCAN is solid and the radio station blinks. When temporarily stopped on a station, SCAN blinks and the station display is solid. Pushing the button again during this five second period stops SCAN tuning and the radio remains tuned to that station

TUNE/FF-REW buttons

WARNING

The radio should not be tuned while driving in order that full attention may be given to the driving operation.

and

Use the buttons for manual tuning. To move quickly through the chan- nels, hold either of the tuning buttons down. SEEK/SCAN buttons SEEK tuning Push the SEEK/SCAN tuning button

or for less than 1.5 seconds. SEEK tuning begins from low to high frequencies or high to low frequencies, depending on which but- ton is pressed, and stops at the next broad- casting station. If using the button once the highest broadcasting station is reached, the radio continues in the SEEK mode at the lowest broadcasting station. If using the button once the lowest broadcasting sta- tion is reached, the radio continues in the SEEK mode at the highest broadcasting station.

4-22 Heater, air conditioner and audio systems

Z X

The selected band illuminates in the dis- play.

2. Tune to the desired station. 3. Push the desired station select button for more than 3 seconds. For example, in the illustrations ch2 is to be memorized. The radio mutes when the select button is pushed.

4. When the indicator illuminates in the display and the sound resumes, memo- rizing is complete.

5. Other station select buttons can be set in

the same manner.

If the battery cable is disconnected, or if the radio fuse opens, the radio memory is can- celled. In that case, reset the desired stations.

AHA1127

Station memory operations Six stations can be set for the AM band. 12
stations can be set for the FM band (six for FM1, six for FM2). 1. Push

to select AM, FM1, or FM2.

Heater, air conditioner and audio systems 4-23

Z X

or

Adjusting tone quality and speaker balance To adjust the audio levels for bass, treble, fader and balance, push the AUDIO button and adjust the level with the TUNE/FF-REW buttons. Press the audio button once for BAS (bass), twice for TRE (treble), three times for FAD (fader) and four times for BAL (balance). Once the audio level is set the display will return back to radio, cassette or CD display mode after 7
seconds or the AUDIO button can be pressed again within 7 seconds to set the next audio level. Pressing the AUDIO button a fifth time will return the display back to radio, cassette or CD display mode. Fader adjusts the sound level between the front and rear speakers, balance adjusts the sound level between the right and left speakers.

4-24 Heater, air conditioner and audio systems

AHA1128

Z X

CASSETTE TAPE OPERATION Turn the ignition key to the ACC or ON position, and carefully insert a cassette tape into the tape door. The cassette tape auto- matically pulls into the player. The word TAPE illuminates in the display. If the radio is already operating it automati- cally turns off and the cassette tape begins to play. The cassette tape automatically changes directions to play the other side when the first side is complete.

CAUTION

Do not force the cassette tape into the tape door. This could cause player damage.

Precautions on cassette player op- eration I To maintain good quality sound, NISSAN recommends using cassette tapes of 60 minutes or shorter in length.

I Cassette tapes should be removed from the player when not in use. Store cassettes in their protective cases

and away from direct sunlight, heat, dust, moisture or magnetic sources. I Direct sunlight can cause the cassette to become deformed. The use of de- formed cassettes may cause the cas- sette to jam in the player.

I Do not use cassettes that have peel- ing or loose labels. If used, the label could jam in the player.

I If a cassette has loose tape, insert a pencil through one of the cassette hubs and rewind the tape firmly. Loose tape may cause jamming and wavering sound quality.

I Over a period of time, the playback head, capstan and pinch roller may gather a tape coating residue as the tape is played. This residue accumu- lation can cause a weak or wavering sound and should be removed peri- odically with a head cleaning tape. If the residue is not removed periodi- cally, the player may need to be disas- sembled for cleaning.

PLAY/STOP TAPE button When the button is pushed with the system turned off and a tape loaded, the

system comes on and the tape plays. The word TAPE illuminates. button is pushed with either When the the radio or compact disc turned on and a tape loaded, the compact disc or the radio turns off and the tape plays. While the tape is playing, pushing the button stops tape play. Pushing the

button again resumes tape play. FF (fast forward) and REW (rewind) buttons

button to fast forward the Push the tape. Push the button to rewind the tape. Either REW or FF illuminates in the display. To stop the FF or REW function, press the Automatic Program Search (APS) SEEK/SCAN buttons

buttons.

, or

button is pushed while the When the tape is being played, the tape runs quickly, stops, then plays the next selection from the button several beginning. Push the times to skip several selections. Each time the button is pushed, the tape fast forwards Heater, air conditioner and audio systems 4-25

Z X

button is pushed,

button to change the tape

one additional selection. This number ap- pears in the display window. The tape can be fast forwarded through up to nine selec- tions. (for example: 7 in the display indi- button has been pushed cates that the seven times to skip forward through seven selections). button is pushed, the selec- When the tion being played starts again from the beginning. Push the button several times to rewind several selections. Each time the the tape rewinds back one additional selection. The number of selections skipped appears in the display window as a negative number (for example: -7 in the display indicates that the button has been pushed seven times to rewind back through seven selections). To stop APS but- ton. Either the FF or REW illuminates in the display when the (FF) but- ton is pushed. The system searches for the blank intervals between selections. If there is a blank inter- val within one selection or there is no inter- val between selections, the system may not stop in the desired or expected location. 4-26 Heater, air conditioner and audio systems

SIDE (Program) button Push the side while the tape is being played. The cassette tape automatically changes directions to play the other side when the first side is complete. Dolby NR (noise reduction) Push the button for Dolby NR en- coded tapes to reduce high frequency tape indicator illuminates in the noise. The display. Dolby NR is manufactured under license from Dolby Laboratories Licensing Corpora- tion. DOLBY NR and the double-D symbol are trademarks of Dolby Laboratories Li- censing Corporation. Metal or chrome tape usage The cassette player is automatically set to high performance play when playing a metal or chrome cassette tape. TAPE EJECT button Push the cassette tape.

button to eject an inserted

, press the

(REW) or

or

COMPACT DISC (CD) PLAYER OPERATION Turn the ignition key to the ACC or ON position and carefully insert the compact disc into the slot with the label side up. The compact disc is automatically pulled into the slot and starts to play. the radio or cassette tape is already If operating, it automatically turns off and the compact disc begins to play.

CAUTION

Do not force the compact disc into the slot. This could damage the player.

CD button When the button is pushed with the compact disc loaded and the tape or the radio playing, the tape or radio turns off and compact disc starts to play. FF (fast forward) REW (rewind) buttons button is pushed When the while the compact disc is playing, the com- pact disc plays at an increased speed while

or

Z X

fast forwarding or rewinding. When the but- ton is released, the compact disc returns to normal play speed. Automatic Program Search (APS) APS FF, APS REW buttons

When the button is pushed while the compact disc is playing, the selection fol- lowing the present one starts to play from the beginning. Push the button several times to skip several selections. Each time the button is pushed, the CD advances one additional selection. The number appears in the display window. (When the last selection on the compact disc is skipped, the first selection is played.) button is pushed, the selec- When the tion being played returns to the beginning. Push the button several times to skip back several selections. Each time the but- ton is pushed, the CD moves back one selection. If the play pattern is in RANDOM buttons are mode when the pushed, the previous or next random selec- tion will be played.

or

RPT/RDM (repeat/random) button

When the button is pushed while the compact disc is playing, the play pattern changes as follows. 1: The current selection is repeated. RANDOM: Selections are played at ran- dom, not following the sequence on the compact disc. The same program may be repeated twice. If the button is pushed in the RANDOM mode, the next selection will be chosen at random. Blank (no symbol): All selections are played repeatedly in sequence. When a new compact disc is inserted, the play pattern automatically changes to ALL. CD EJECT button When the button is pushed with a com- pact disc loaded, the compact disc ejects. When the button is pushed while the compact disc is playing, the compact disc ejects and the system turns off. If the compact disc ejects and is not

removed within 10 seconds, it is pulled back into the slot. CD (DISC) indicator light This light comes on when a compact disc is loaded into the player.

CAUTION

I During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely.

I The player may skip while driving on

rough roads.

I The CD player sometimes cannot function when the compartment tem- perature is extremely high. Decrease the temperature before use.

I Do not expose the CD to direct sun-

light.

I Do not touch the playing surface of

the disc.

I Do not use 8 cm discs. They may cause player damage even if using with the optional adapter.

Heater, air conditioner and audio systems 4-27

Z X

I Recordable compact discs (CD-R) may not function properly in the CD player.

ANTENNA

CAR PHONE OR CB RADIO

The antenna cannot be shortened, but it can be removed. When you need to remove the antenna, turn the antenna rod counterclock- wise. To install the antenna rod, turn the antenna clockwise. Tighten the antenna rod to speci- fication using a suitable tool such as a open-end wrench. The antenna rod tighten- ing specification is 3.4 - 3.6 N(cid:215) m (30 - 32
in-lb). Do not use pliers to tighten the an- tenna as they can leave marks on the antenna surface. The antenna rod can not be hand tightened to the proper specifica- tion.

CAUTION

Always properly tighten the antenna rod during installation or the antenna rod may break during vehicle opera- tion.

Microphone installed model If equipped with a genuine NISSAN cellular phone (US only), your NISSAN features a non-directional microphone in the steering column cover, so it is not necessary to look at or speak directly into the microphone when calling. To do so could detract from the driving operation and cause an acci- dent. See the manual for car phone opera- tion. Pre-wired and antenna for phone installed model Some models are pre-wired to accept the genuine NISSAN cellular phone (US only). In addition, the same model has the phone antenna built into the rear glass window. When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following cautions, otherwise the new equipment may adversely affect the MFI (Multiport Fuel Injection) system and other electronic parts.

4-28 Heater, air conditioner and audio systems

Z X

I If a conversation in a moving vehicle requires you to take notes, pull off the road to a safe location and stop your vehicle before doing so.

CAUTION

I Keep the antenna as far away as possible from the Engine Control Module (ECM).

I Keep the antenna wire more than 8
in. (20 cm) away from the Multiport Fuel Injection harness. Do not route the antenna wire next to any har- ness.

I Adjust the antenna standing-wave ratio as recommended by the manu- facturer.

I Connect the ground wire from the

CB radio chassis to the body.

I For details, consult an authorized

NISSAN dealer.

AHA1053

WARNING

I A cellular telephone should not be used while driving so full attention may be given to vehicle operation. Some jurisdictions prohibit the use of cellular telephones while driving. I If you must make a call while your vehicle is in motion, the hands free cellular phone operational mode (if so equipped) is highly recom- mended. Exercise extreme caution at all times so full attention may be given to vehicle operation.

Heater, air conditioner and audio systems 4-29

Z X

MEMO

4-30 Heater, air conditioner and audio systems

Z X

5 Starting and driving

Precautions when starting and driving ...................5-2
Exhaust gas (carbon monoxide) ............................5-2
Three-way catalyst..................................................5-2
On-pavement and off-road driving precautions......5-3
Avoiding collision and rollover................................5-3
Drinking alcohol/drugs and driving .........................5-4
Driving safety precautions......................................5-4
Ignition switch.........................................................5-6
Manual transmission...............................................5-6
Automatic transmission ..........................................5-7
Before starting the engine ......................................5-8
Driving with automatic transmission (if so equipped) ...............................................................5-8
Overdrive switch (KA24DE engine) .....................5-13
Overdrive switch (VG33E engine)........................5-14
Driving with manual transmission.........................5-14

Starting the engine ...............................................5-16
Parking brake operation.......................................5-16
Cruise control (if so equipped).............................5-18
Break-in schedule ................................................5-20
Increasing fuel economy ......................................5-20
Transfer case shifting procedures for 4-wheel drive vehicles........................................................5-21
Auto-lock free-running hubs .................................5-22
Manual-lock free-running hubs.............................5-24
Tires of four-wheel drive ......................................5-26
Parking/parking on hills ........................................5-27
Power steering system.........................................5-28
Brake system........................................................5-28
Anti-lock brake system (ABS) ..............................5-29
Cold weather driving ............................................5-30

Z X

PRECAUTIONS WHEN STARTING AND DRIVING

WARNING

I Do not

leave children, unreliable adults, or pets alone in your vehicle. They could accidentally injure them- selves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or pos- sibly fatal injuries to people or ani- mals.

I Properly secure all cargo to help prevent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.

EXHAUST GAS (carbon monoxide)

WARNING

I Do not breathe exhaust gases; they contain colorless and odorless car- bon monoxide. Carbon monoxide is dangerous. It can cause uncon- sciousness or death.

5-2 Starting and driving

I If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately.

I Do not run the engine in closed

spaces such as a garage.

I Do not park the vehicle with the engine running for any extended length of time.

I If a special body, camper, or other equipment is added for recreational or other usage, follow the manufac- turer’s recommendation to prevent carbon monoxide entry into the ve- hicle. Do not occupy these areas while the engine is running even if the vehicle is parked. Some recreational vehicle appliances such as stoves, refrigerators, heaters, etc. may also generate carbon monoxide.

I The exhaust system and body should be inspected by a qualified mechanic whenever: a. The vehicle is raised for service.

b. You suspect that exhaust fumes are entering into the passenger compartment.

c. You notice a change in the sound

of the exhaust system.

d. You have had an accident involv- ing damage to the exhaust system, underbody, or rear of the vehicle.

THREE-WAY CATALYST The three-way catalyst is an emission control device installed in the exhaust system. Ex- haust gases in the converter are burned at high temperatures to help reduce pollutants.

WARNING

I The exhaust gas and the exhaust system are very hot. Keep people, animals or flammable materials away from the exhaust system com- ponents.

I Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.

Z X

CAUTION

I Do not use leaded gasoline. Depos- its from leaded gasoline seriously reduce the three-way catalyst’s abil- ity to help reduce exhaust pollut- ants.

I Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause over- rich fuel flow into the three way cata- lyst, causing it to overheat.

I Do not keep driving if the engine misfires, or if noticeable loss of per- formance or other unusual operating conditions are detected. Have the vehicle inspected promptly by an authorized NISSAN dealer.

I Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damag- ing the three-way catalyst.

I Do not race the engine while warm-

ing it up.

I Do not push or tow your vehicle to

start the engine.

ON-PAVEMENT AND OFFROAD DRIVING PRECAUTIONS Utility vehicles have a significantly higher rollover rate than other types of vehicles. They have higher ground clearance than passenger cars to make them capable of performing in a variety of on-pavement and offroad applications. This gives them a higher center of gravity than ordinary cars. An advantage of higher ground clearance is a better view of the road, allowing you to anticipate problems. However, they are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfactorily under off road conditions. If at all possible, avoid sharp turns or abrupt maneuvers particu- larly at high speeds. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or vehicle rollover. Be sure to read the driving safety precau- tions later in this section.

AVOIDING COLLISION AND ROLLOVER

WARNING

Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident.

Be alert and drive defensively at all times. Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steering maneuvers, because these driving practices could cause you to lose control of your vehicle. As with any vehicle, a loss of control could result in a collision with other vehicles or objects, or cause the vehicle to rollover, particularly if the loss of control causes the vehicle to slide sideways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (including prescription or over-the-counter drugs which may cause drowsiness). Al- ways wear your seat belt as outlined in the † Seats, restraints and supplemental air bag systems† section of this manual, and also instruct your passengers to do so. Seat belts help reduce the risk of injury in Starting and driving 5-3

Z X

collisions and rollovers. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. DRINKING ALCOHOL/DRUGS AND DRIVING

WARNING

Never drive under the influence of alco- hol or drugs. Alcohol in the blood- stream reduces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in the accident, alcohol can increase the se- verity of the injury.

NISSAN is committed to safe driving. How- ever, you must choose not to drive under the influence of alcohol. Every year thou- sands of people are injured or killed in alcohol related accidents. Although the local laws vary on what is considered to be legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol. 5-4 Starting and driving

Remember, drinking and driving don’t mix! And that’s true for drugs, too (over the counter, prescription, and illegal drugs). Don’t drive if your ability to operate your vehicle is impaired by alcohol, drugs, or some other physical condition. DRIVING SAFETY PRECAU- TIONS Your NISSAN is designed for both normal and offroad use. However, avoid driving in deep water or mud as your NISSAN is mainly designed for leisure use, unlike a conventional offroad vehicle. Remember that two wheel drive models are less capable than four wheel drive models for rough road driving and extrication when stuck in deep snow or mud, or the like. Please observe the following precautions:

WARNING

I Drive carefully when off the road and avoid dangerous areas. Every per- son who drives or rides in this ve- hicle should be seated with their seat belt fastened. This will keep you and your passengers in position

when driving over rough terrain.

I Do not drive across steep slopes. Instead drive either straight up or straight down the slopes. Off-road vehicles can tip over sideways much more easily than they can forward or backward.

I Many hills are too steep for any ve- hicle. If you drive up them, you may stall. If you drive down them, you may not be able to control your speed. If you drive across them, you may roll over.

I Do not shift gears while driving on downhill grades as this could cause loss of control of the vehicle.

I Stay alert when driving to the top of a hill. At the top there could be a drop-off or other hazard that could cause an accident.

I If your engine stalls or you cannot make it to the top of a steep hill, never attempt to turn around. Your vehicle could tip or roll over. Always back straight down in R (Reverse) gear. Never back down in N (Neutral)

Z X

or with the clutch depressed (manual transmission vehicles), us- ing only the brake, as this could cause loss of control.

I Heavy braking going down a hill could cause your brakes to overheat and fade, resulting in loss of control and an accident. Apply brakes lightly and use a low gear to control your speed.

I Unsecured cargo can be thrown around when driving over rough ter- rain. Properly secure all cargo so it will not be thrown forward and cause injury to you or your passengers.

the roof

I To avoid raising the center of gravity excessively, do not exceed the rated capacity of rack (if so equipped) and evenly distribute the load. Secure heavy loads in the cargo area as far forward and as low as possible. Do not equip the vehicle with tires larger than specified in this manual. This could cause your ve- hicle to roll over.

I Do not grip the inside or spokes of the steering wheel when driving off-

road. The steering wheel could move suddenly and injure your hands. In- stead drive with your fingers and thumbs on the outside of the rim.

I Before operating the vehicle, ensure that the driver and all passengers have their seat belts fastened.

I Always drive with the floor mats in place as the floor may become hot. I Lower your speed when encounter- ing strong crosswinds. With a higher center of gravity, your NISSAN is more affected by strong side winds. Slower speeds ensure better vehicle control.

I Do not drive beyond the perfor- mance of the tires, even with 4WD engaged.

I Accelerating quickly, sharp steering maneuvers or sudden braking may cause loss of control.

I If at all possible, avoid sharp turning maneuvers, particularly at high speeds. Your NISSAN four wheeld- rive vehicle has a higher center of gravity than a two wheel drive veh-

icle. The vehicle is not designed for cornering at the same speeds as conventional two wheel drive ve- hicles. Failure to operate this vehicle correctly could result in loss of con- trol and/or a roll over accident.

I Always use tires of the same type, size, brand, construction (bias, bias- belted, or radial), and tread pattern on all four wheels. Install tire chains on the rear wheels when driving on slippery roads and drive carefully.

I Be sure to check the brakes immedi- ately after driving in mud or water. See † Brake system† later in this sec- tion for † Wet brakes† .

I Avoid parking your vehicle on steep hills. If you get out of the vehicle and it rolls forward, backward or side- ways, you could be injured.

I Whenever

you

drive

off-road through sand, mud or water as deep as the wheel hub, more frequent- maintenance may be required. See † Periodic maintenance† in the † Main- tenance† section of this manual.

Starting and driving 5-5

Z X

clockwise from the straight up position. To unlock the steering wheel, insert the key and turn it gently while rotating the steering wheel slightly right and left.

WARNING

Never remove or turn the key to the LOCK position while driving. The steer- ing wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.

IGNITION SWITCH

ASD1015

MANUAL TRANSMISSION The ignition switch includes an anti-theft steering lock device. The key can only be removed when the ignition switch is in the LOCK position. On manual transmission models, to turn the ignition key to LOCK from ACC or ON, turn the key to OFF, push the key in, then turn the key to LOCK. To lock the steering wheel, turn the key to the LOCK position. Remove the key. In order for the steering wheel to be locked, it must be turned about 1/8 of a turn 5-6 Starting and driving

Z X

ASD1014

AUTOMATIC TRANSMISSION On automatic transmission models, the ig- nition lock is designed so the key cannot be turned to LOCK and removed until the shift selector lever is moved to the P (Park) position. When removing the key from the ignition, make sure the shift selector lever is in the P (Park) position. If the key cannot be turned to the LOCK position, proceed as follows to remove the key: 1) Move the shift selector lever into the P

(Park) position.

2) Turn the ignition key slightly in the ON

direction.

gently while rotating the steering wheel slightly right and left.

3) Turn the key toward the LOCK position. 4) Remove the key. The shift lever is designed so it cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to OFF or if the key is removed from the switch. The shift lever can be moved if the igni- tion switch is in the ACC position. This allows the vehicle to be moved if the battery is discharged. The shift lever can also be moved if the ignition switch is in the ON position and the foot brake pedal is depressed. There is an OFF position between the LOCK and ACC positions. The OFF posi- tion is indicated by a † 1† on the key cylinder. When the ignition is in the OFF position, is not locked. To lock the steering wheel, turn the key to the LOCK position. Remove the key. In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clockwise from the straight up position. To unlock the steering wheel, insert the key and turn it

the steering wheel

WARNING

Never remove or turn the key to the LOCK position while driving. The steer- ing wheel will lock. This may cause the driver tolose control of the vehicle and could result in serious vehicle damage or personal injury.

Key positions LOCK Normal parking position (0) OFF (Manual transmission model) (1) The engine can be turned off without locking the steering wheel. ACC (Accessories) (2) This position activates electrical accesso- ries such as the radio when the engine is not running. The shifter can be moved if the ignition switch is in ACC position. ON (Normal operating position) (3) This position turns on the ignition system and electrical accessories.

Starting and driving 5-7

Z X

START (4) This position starts the engine. As soon as the engine has started, release the key. It automatically returns to the ON position.

BEFORE STARTING THE ENGINE I Make sure the area around the vehicle is

clear.

I Check fluid levels such as engine oil, coolant, brake and clutch fluid, and win- dow washer fluid as frequently as pos- sible, at least whenever you refuel.

I Check that all windows and lights are

clean.

I Visually inspect tires for their appearance and condition. Also check tires for proper inflation.

I Lock all doors. I Position seat and adjust head restraints. I Adjust inside and outside mirrors. I Fasten seat belts and ask all passengers

to do likewise.

I Check the operation of warning lights when key is turned to the ON (3) position. See and chimes† in the † Instruments and con- trols† section.

† Warning/Indicator

lights

DRIVING WITH AUTOMATIC TRANSMISSION (if so equipped)

WARNING

I Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to R (Reverse), D (Drive), 2
or 1. Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose con- trol and have an accident.

I Cold engine idle speed is high, so use caution when shifting into a for- ward or reverse gear before the en- gine has warmed up.

I Never shift to P (Park) or R (Reverse) while the vehicle is moving. This could cause an accident.

CAUTION

I When stopping the vehicle on an uphill grade, do not hold the vehicle by depressing the accelerator pedal. The foot brake should be used for this purpose.

I On slippery roads, do not downshift.

This may cause a loss of control.

5-8 Starting and driving

Z X

LOCK or if the key is removed. If the battery charge is low, the shift lever can be moved if the ignition switch is in the ACC position.

The automatic transmission in your vehicle is electronically controlled by a transmission control module to produce maximum power and smooth operation. The recommended operating procedures for this transmission are shown on the following pages. Follow these procedures for maximum vehicle performance and driving enjoyment. Starting the vehicle I After starting the engine, fully depress the foot brake pedal to ensure the ve- hicle is at a complete stop before at- tempting to shift the selector lever.

I Keep the foot brake pedal depressed and shift the selector lever into a driving gear.

I Release the foot brake, then gradually

start the vehicle in motion.