2008 Nissan Armada Owners Manual

motion.

Monitor, climate, audio, phone and voice recognition systems 4-73

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

c Do not store the cards in highly humid loca-

tions.

c Do not expose the cards to direct sunlight. c Do not spill any liquids on the cards. Refer Manual for more details.

to the CompactFlash(cid:153) card Owner(cid:146)s

CF cards:

LHA1002

CAUTION

Do not force the CompactFlash(cid:153) card into the CompactFlash(cid:153) player slot. Forcing the CF card could damage the pins inside the CF player slot, especially if the CF card is upside down or backwards.

c Never touch the terminal portion of the Com-

pactFlash(cid:153) cards. Do not bend the cards.

c Always place the cards in the storage case

when they are not being used.

c Do not place heavy objects on the cards.

4-74 Monitor, climate, audio, phone and voice recognition systems

WHA0611

Type A Volume control switch 1. 2. MODE select switch 3. 4.

POWER on/off switch Tuning switch

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

WHA0612

Type B Volume control switch Phone operation switch POWER on and MODE select switch Tuning switch

1. 2. 3. 4. STEERING WHEEL SWITCH FOR AUDIO CONTROL The audio system can be operated using the controls on the steering wheel. POWER on/off switch With the ignition key turned to the ACC or ON position, push the POWER switch to turn the audio system on or off.

If you have the Type B switch, with the ignition key turned to the ACC or ON position push the MODE switch to turn the audio system on. MODE select switch Push the mode select switch to change the mode in the following sequence: PRESET A ! PRE- SET B ! PRESET C ! Music Box** (if so equipped) ! CD* ! CompactFlash(cid:153)* (if so equipped) ! DVD* (if so equipped) ! AUX***. *These modes are only available when compat- ible media storage is inserted into the device. **This mode is only available when music has been downloaded into the Music Box hard-disk drive audio system. ***This mode is only available when a compatible auxiliary device is plugged into the AUX jack. Volume control switch Push the volume control switch up or down to increase or decrease the volume.

Tuning

Memory change (radio): While in one of the preset radio station banks (A, B or C), push the tuning switch for less than 1.5 seconds to change to the next preset station in memory.

or

Seek tuning (radio):

for more Push the tuning switch than 1.5 seconds to seek the next or previous radio station. Next/Previous track (CD/CF):

or

Push the tuning switch for less than 1.5 seconds to return to the beginning of the present track or skip to the next track. Push several times to skip back or skip through tracks.

or

This system searches for the blank intervals be- tween selections. If there is a blank interval within 1 program or there is no interval between pro- grams, the system may not stop in the desired or expected location. Next/Previous track (Music Box):

Push the tuning switch for less than 1.5 seconds to return to the beginning of the present track or skip to the next track. Push several times to skip back or skip through tracks.

or

Push and hold the tuning switch for more than 1.5 seconds to change playlists. When the last playlist is playing, the next playlist will be selected.

or

Monitor, climate, audio, phone and voice recognition systems 4-75

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

Change disc (CD) (if so equipped): Push the tuning switch for more than 1.5 seconds to change the playing disc up or down.

or

VOL (volume) control button

1. 2. MODE select button 3. 4. 5. 6. Headphone jacks

NEXT button SEEK button

speaker control button

7.

Infrared headphone transmitter lens*

LHA0322

*Red transmitters will be visible when infrared headphones are on.

4-76 Monitor, climate, audio, phone and voice recognition systems

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

ANTENNA Window antenna The antenna pattern is printed inside the rear passenger and driver side windows.

CAUTION

c Do not place metalized film near the rear driver or passenger side window glass or attach any metal parts to it. This may cause poor reception or noise.

c When cleaning the inside of the rear driver or passenger side window, be careful not to scratch or damage the window antenna. Lightly wipe along the antenna with a dampened soft cloth.

REAR AUDIO CONTROLS Press the REAR CTRL button on the front radio control panel to turn the rear controls on. Press the button again to turn rear controls off.

Press the button; the headphones symbol illuminates on the front display when the head- phones are on. Two headphone jacks are pro- vided so two rear seat passengers may listen to the audio system privately.

One or two infrared headphones are included if the vehicle is equipped with the DVD entertain- ment system. Most portable radio headphones work with the rear audio controls.

For vehicles equipped with the FM/AM/SAT radio with compact disc player, if the rear passengers turn off the rear speakers and are using head- phones they may choose to listen to a different media than the front passengers. The rear pas- sengers can listen to the radio along with the front passengers or they can listen to a CD or SAT radio (if so equipped). VOL (volume) button: The VOL button allows the rear passengers to adjust the headphone volume level. The vehicle volume can also be changed if the REAR CTRL is enabled and the rear audio mode is the same as the front.

(SPEAKER CONTROL) button:

Press this button to turn the rear speakers off and headphones on. Press this button again to turn rear seat speakers back on and headphones off. MODE button: The MODE button allows the rear passengers to change between AM, FM, CD, DVD and AUX. The media options are listed on the face plate of the rear audio controls. When a source of media is selected, the media label will be illuminated. SEEK button: In AM or FM mode, the SEEK button allows the rear seat passengers to find the next radio station up or down the station band frequency. In CD mode, the SEEK button allows the rear passengers to find the next or previous selection on the CD. NEXT button: When the NEXT button is pressed while in AM or FM mode, the radio will change to the next preset. The NEXT button does not function while in SAT radio mode or when playing a DVD or CD.

Monitor, climate, audio, phone and voice recognition systems 4-77

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

Movies will not be shown on the front display while the vehicle is in any drive position to reduce driver distraction. Audio is available when a movie is played. To view movies in the front display, stop the vehicle in a safe location, move the selector lever to the P (Park) position and apply the park- ing brake.

NISSAN MOBILE ENTERTAINMENT SYSTEM (MES) (if so equipped)

WHA0966
This vehicle is equipped with the mobile enter- tainment system, which enables you to play a Digital Versatile Disc (DVD), providing the im- ages and sounds both in the front and rear dis- play screens.

WARNING

c The driver must not attempt to operate or view the Mobile Entertainment Sys- tem while the vehicle is in motion so that full attention may be given to ve- hicle operation.

c Do not attempt to modify the system to display a movie on the front screen while the vehicle is being driven. Doing so may distract the driver and may cause a collision and serious personal injury or death.

CAUTION

c The glass screen on the liquid crystal display may break if hit with a hard or sharp object. If the glass breaks, do not touch the liquid crystalline material, which contains a small amount of mer- cury. In case of contact with skin, wash immediately with soap and water.

c Use a damp, soft cloth when cleaning the Mobile Entertainment System com- ponents. Do not use solvents or clean- ing solutions.

Do not attempt to use the system in extreme temperature conditions [below -4(cid:176)F (-20(cid:176)C) or above 158(cid:176)F (70(cid:176)C)]. To avoid discharging the vehicle battery, do not operate the system more than 15 minutes without starting the engine.

4-78 Monitor, climate, audio, phone and voice recognition systems

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

EJECT button DVD slot Auxiliary input jack

1. 2. 3. DIGITAL VIDEO DISC (DVD) PLAYER CONTROLS

3. Auxiliary input jack:

For information, see (cid:147)DVD auxiliary input jacks(cid:148) later in this section.

1.

EJECT button:

WHA0967

button is pressed with the

When the DVD loaded, it will be ejected. The display will show the eject symbol in the upper left corner of the display for 4 seconds once the If the DVD is not loaded, the display will show (cid:147)NO DISC(cid:148). If the DVD comes out and is not removed within 25 seconds, it will be pulled back into the slot to protect it.

button is pressed.

2. DVD slot:

Insert a DVD into the slot with the label side facing up. The DVD will be guided automati- cally into the slot.

Monitor, climate, audio, phone and voice recognition systems 4-79

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

DISPLAY button

6. 7. MODE button SUBTITLE button 8. 9. AUDIO button 10. ANGLE button 11. CLEAR button 12. PAUSE button 13. PLAY button 14. FAST FORWARD/FAST REVERSE

button

15. MENU button 16. NAVIGATION keys 17. BACK button 18. NUMERIC KEYPAD REMOTE CONTROL Refer to (cid:147)Remote controller operation(cid:148) later in this section for the function of each button.

LHA0317

1. 2. 3.

POWER button STOP button NEXT TRACK/CHAPTER and PREVI- OUS TRACK/CHAPTER button TITLE button ENTER button

4. 5. 4-80 Monitor, climate, audio, phone and voice recognition systems

LHA0315

FLIP-DOWN SCREEN The flip-down screen has a wireless remote con- trol receiver s1 located at the bottom of the screen.

CAUTION

c The glass screen on the liquid crystal display may break if hit with a hard or sharp object. If the glass breaks, do not touch the liquid crystalline material, which contains a small amount of mer- cury. In case of contact with skin, wash immediately with soap and water.

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

c The screen rotates down to view and up into the housing to store when not in use. Ensure that the screen is latched securely into the housing when stored.

SAA0720

SAA0721

Headphones Power ON/OFF:

Press the power button to turn the headphones on or off. Volume control:

Turn the volume control knob to adjust the vol- ume.

The headphones will automatically be turned off in 30 seconds if there is no sound during that period. To prevent the battery from being dis- charged, keep the power supply turned off when not in use.

NOTE: For optimum infrared headphone perfor- mance, increase the volume on the rear seat controller to the maximum level and adjust the infrared headphone volume us- ing the volume control on the headphones. Using a lower volume setting on the rear seat controller can cause static noise in the infrared headphones.

Monitor, climate, audio, phone and voice recognition systems 4-81

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

BEFORE OPERATING THE DVD MOBILE ENTERTAINMENT SYSTEM Precautions

Start the engine when using the DVD entertain- ment system.

WARNING

The driver must not attempt to operate the DVD System or wear the headphones while the vehicle is in motion so that full attention may be given to vehicle operation.

CAUTION

c Only operate the DVD while the vehicle engine is running. Operating the DVD for extended periods of time with the engine OFF can discharge the vehicle battery.

c Do not allow the system to get wet. Excessive moisture such as spilled liq- uids may system to malfunction.

cause

the

While playing VIDEO-CD media, this DVD player does not guarantee complete functionality of all VIDEO-CD formats.

Disc selection You can play the following disc formats with the DVD drive: c DVD-VIDEO c VIDEO-CD c CD-DA (Conventional Compact Disc) (CD

with MP3/WMA cannot be played.)

Use DVDs with a region code 1, ALL or 1 in- cluded for your DVD entertainment system. The region code is displayed as a small symbol printed on the top of the DVD. This vehicle- installed DVD player cannot play DVDs with a region code other than 1 or ALL.

Copyright and trademark c The technology protected by the U.S. patent and other intellectual property rights owned by Macrovision Corporation and other right holders is adopted for this system.

c This copyright protected technology cannot be used without a permit from Macrovision Corporation. It is limited to be personal use, etc., as long as the permit from Macrovision Corporation is not issued.

c Modifying or disassembling is prohibited. c Dolby digital is manufactured under license

from Dolby Laboratories, Inc.

c Dolby and the double D mark are trademarks

of Dolby Laboratories, Inc.

c DTS and DTS Digital Surround are regis- tered trademarks of Digital Theater Systems, Inc.

Parental level (parental control) DVDs with the parental control setting can be played with this system. Please use your own judgement to set the parental control with the system.

4-82 Monitor, climate, audio, phone and voice recognition systems

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

Rear display: To adjust the rear display mode, press the DISP (Display) button on the remote controller. To adjust the display brightness, tint, color and contrast, select each key using the joystick on the remote controller and tilt the joystick to right or left. Press the BACK button to apply the settings and return to the previous display

WHA0968

Display settings Front display: To adjust the front display mode, press the SET- TING button while the DVD is being played, select the (cid:147)Display(cid:148) key with the NISSAN control- ler, and then press the ENTER button. To adjust the display ON/OFF, brightness, tint, color, con- trast and black level select each key using the NISSAN controller and press the ENTER button. Then you can adjust each item using the NISSAN controller. After changes have been made press the BACK button to save the settings.

LHA0972

PLAYING A DIGITAL VERSATILE DISC (DVD) With the DVD player, you can hear DVD videos, video CDs and CDs using headphones. Passen- gers in the rear seat can enjoy the sound inde- pendently of the front seat. Press the DISC/AUX button located on the front controls to hear the sound of the DVD play through the speakers. Press the REAR CTRL button located on the front controls to disable or enable rear seat audio controls. For more information on rear seat audio controls see, (cid:147)Rear Audio Controls(cid:148) earlier in this section.

Monitor, climate, audio, phone and voice recognition systems 4-83

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

button on the front controls Pressing the turns the rear speakers on or off and enables or disables the wireless headphones .

It is possible to operate the DVD player by remote control.

Headphones are a wireless type and no cables are necessary. You can use them in almost all the ranges in the rear seat. (It is not possible to use the headphones in the front seat.) DISC/AUX button Park the vehicle in a safe location for the front seat occupants to operate the DVD drive while watching the images.

Press the DISC/AUX button on the instrument panel and turn the display to the DVD mode.

When a DVD is loaded, it will be replayed auto- matically.

The operation screen will be turned on when the DISC/AUX button located on the instrument panel is pressed while a DVD is being played, and it will turn off automatically after a period of time. To turn it on again, press the DISC/AUX button once more.

DVD operation keys To operate the DVD drive, touch the preferred key (if so equipped) or select the preferred key dis- played on the operation screen using the NISSAN controller.

NOTE:

If the display in your vehicle is not touch screen enabled; use the NISSAN controller and the ENTER button to operate the fol- lowing functions. For more information on how to operate the NISSAN controller see, (cid:147)How to use the NISSAN controller(cid:148) earlier in this section.

PAUSE key:

Touch the (cid:147) To resume playing the DVD, (cid:147)

(cid:148) PAUSE key to pause the DVD. touch the

(cid:148)PLAY key.

To pause the DVD, it is also possible to press the button on the keypad of the remote controller.

PLAY key:

Touch the (cid:147) DVD, for example, after pausing the DVD

(cid:148) PLAY key to start playing the

To start playing the DVD, it is also possible to button on the keypad of the press the remote controller.

STOP key:

Touch the (cid:147) DVD.

(cid:148) STOP key to stop playing the

To stop playing the DVD, it is also possible to press the button on the keypad of the remote controller.

SKIP (forward) key:

Touch the (cid:147) (cid:148) SKIP key to skip the chapter( s) of the disc forward. The chapters will advance the number of times the (cid:147) (cid:148) SKIP key is touched.

(cid:148) SKIP key for more Touch and hold the (cid:147) than 1.5 seconds to fast forward the disc. When the (cid:147) (cid:148) SKIP key is released the disc will be played normally.

To skip the chapter(s) forward, it is also possible to press the button on the keypad of the remote controller.

4-84 Monitor, climate, audio, phone and voice recognition systems

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

SKIP (rewind) key:

Touch the (cid:147) (cid:148) SKIP key to skip the chapter(s) of the disc backward. The chapters will go back the number of times the (cid:147) (cid:148) SKIP key is touched. Touch and hold the (cid:147) (cid:148) SKIP key for more than 1.5 seconds to rewind the disc. When the (cid:147) (cid:148) SKIP key is released the disc will be played normally. To skip the chapter(s) backward, it is also pos- sible to press the button on the keypad of the remote controller.

LHA0969

LHA0970

DVD settings Touch the (cid:147)Settings(cid:148) key to adjust the following settings while playing a DVD.

When all the changes have been made, press BACK button to save all the settings.

NOTE: If the display in your vehicle is not touch screen enabled; use the NISSAN controller and the ENTER button to operate the fol- lowing functions. For more information on how to operate the NISSAN controller see, (cid:147)How to use the NISSAN controller(cid:148) earlier in this section.

Monitor, climate, audio, phone and voice recognition systems 4-85

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

Switch to DVD-AUX:

Angle:

Switch the output source from the DVD drive to another device connected to the auxiliary input jacks located on the DVD player.

If the DVD contains different angles (such as moving images), the current image angle can be switched to another one.

For more information, see (cid:147)DVD auxiliary input jacks(cid:148) later in this section. Menu:

Choose a different angle by touching the (cid:147)(cid:150)(cid:148) key or the (cid:147)+(cid:148) key; the angle will change if available. Angle Mark:

LHA0971

Some menus specific to each DVD will be shown. For details, see the instructions attached to the DVD. Top Menu:

Each title menu in the disc will be shown. For details, see the instructions attached to the DVD. Audio:

Some audio tracks specific to each DVD will be shown. For details, see the instructions attached to the DVD. Subtitle:

Choose the preferred DVD subtitle language by touching the (cid:147) Display Mode:

(cid:148) key or the (cid:147)

(cid:148) key.

4-86 Monitor, climate, audio, phone and voice recognition systems

Choose from the Full, Wide, Normal or the Cin- ema mode by touching the (cid:147) (cid:148) key or the (cid:147)

(cid:148) key.

When this item is turned on, an angle mark will be shown on the bottom of the screen if the scene can be seen from a different angle. Touch the (cid:147)ON(cid:148) key to enable the angle mark; the indicator light will illuminate. 10Key Search:

Touch the (cid:147)10Key Search(cid:148) key to open the num- ber entry screen. Input the number you want to search for and touch the (cid:147)OK(cid:148) key. The specified Title/Chapter or Group/Track will be played. Title Search:

The scene with the specified title will be dis- played the number of times the (cid:147)(cid:150)(cid:148) key or the (cid:147)+(cid:148) key is touched. Menu Skip:

DVD menus are automatically configured and the contents will be played directly when the (cid:147)Menu

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

Skip(cid:148) key is turned on. Note that some discs may not be played directly even if this item is turned on. DVD Language: Touch the (cid:147)DVD Language(cid:148) key to open the num- ber entry screen. Input the number correspond- ing to the preferred language and touch the (cid:147)OK(cid:148) key. The DVD top menu language will be changed to the one specified. DRC: DRC (Dynamic Range Compression) allows you to tune the dynamic range of the sound recorded in the DolbyT Digital format. Touch the (cid:147)(cid:150)(cid:148) key or the (cid:147)+(cid:148) key to tune the DRC. DVD auxiliary input jacks The auxiliary input jacks are located on the front of the DVD player which is located inside the center console. NTSC and PAL compatible devices such as video games, camcorders and portable video players can be connected to the auxiliary jacks. The auxiliary jacks are color coded for identifica- tion purposes. c Yellow - video input c White - left channel audio input c Red - right channel audio input

Before connecting a device to a jack, power off the portable device and turn off the DVD player. To view something connected to the auxiliary input jacks, press the DISC/AUX button until the DVD mode appears, then select the (cid:147)Settings(cid:148) key using the NISSAN controller and press the ENTER button. Then select the (cid:147)Switch to DVD- AUX(cid:148) key using the NISSAN controller and press the ENTER button. The screen will change to the DVD-AUX mode.

LHA0973

DVD-AUX settings

Select the (cid:147)Settings(cid:148) key using the NISSAN con- troller and press the ENTER button to adjust the following settings: c Switch to DVD

Select to switch back to the DVD mode.

c Video Format:

If the auxiliary source is in a different video format, select the (cid:147) (cid:148) key using the NISSAN controller and press the ENTER button; the video format will change.

(cid:148) key or the (cid:147)

Monitor, climate, audio, phone and voice recognition systems 4-87

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

The DVD system can also be controlled by using the remote controller in the rear seats. See the following items. PWR on/off button:

With the ignition switch turned to the ACC or ON position, press the PWR button to turn the DVD rear display on or off.

NOTE:

The PWR button on the remote control only turns the rear display on or off.

Insert the DVD into the slot with the label side facing up. The DVD will be guided automatically into the slot.

If the DVD player is off and a DVD is inserted, the DVD player will automatically turn on.

CAUTION

Do not force the compact disc into the slot. This could damage the player.

MODE select button:

Press the MODE button to select Audio/Video source between DVD and AUX input (input jacks on the faceplate, Red = right channel audio input, White = left channel audio input, and Yellow = Video input).

LHA0974

c Display Mode:

Choose from the Full, Wide, Normal or Cin- ema mode by selecting the (cid:147) (cid:148) key or the (cid:147) (cid:148) key using the NISSAN controller and press the ENTER button.

When all the changes have been made, press the BACK button to save all the settings. REMOTE CONTROL OPERATION For all operation precautions, see (cid:147)Before oper- ating the DVD Mobile Entertainment System(cid:148) earlier in this section.

4-88 Monitor, climate, audio, phone and voice recognition systems

The display will show the (cid:147)AUX(cid:148) in the upper left corner of the display for 4 seconds once the Mode is changed to AUX. To use the input jacks, refer to (cid:147)Auxiliary input jacks(cid:148) in this section.

PLAY:

PLAY button on the remote

When the control is pressed, the player will play. In play mode, the display will briefly show on the upper left corner of the display.

FF (Fast Forward), REW:

(fast forward) /

Press (Rewind) but- tons to carry out the fast forward or rewind pre- sentation at 5 times normal play speed. Press (Rewind) but- tons again or PLAY button to resume the normal play speed.

(fast forward) /

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

NEXT CHAPTER/ PREVIOUS CHAPTER:

When the (NEXT CHAPTER) button is pressed while the DVD is being played, the pro- gram next to the present one will start to play from its beginning. Press several times to skip through programs. The DVD will advance the number of times the button is pressed. When the (PREVIOUS CHAPTER) button is pressed, the program being played returns to its beginning. Press several times to skip back through pro- grams. The DVD will go back the number of times the button is pressed.

PAUSE:

When the PAUSE button on the remote control is pressed, the player will pause playing of In pause mode, the media. the player will show on the upper left corner of the dis- play until the player is changed to another mode.

STOP:

Press the STOP button once to stop playing the media. The display will show in the upper left corner of the display for 4 seconds, and the last disc position will be stored. When the PLAY button is pressed again, it will resume at the stored disc track and time position.

If the STOP button is pressed again when the player is already in Stop mode, it will reinitialize the pointer to the beginning of the disc. In effect it will ignore the last stored disc position and upon receipt of the next play message it will begin at the Title Menu, or at (cid:147)the beginning of the disc(cid:148). DISPLAY:

If the DISPLAY control is pressed for less than 2
seconds, the display menu will appear on the screen. c The display menu will remain on the screen for 10 seconds if no subsequent control activations occur.

c Use NAVIGATION KEYS to navigate within the display menu, and use ENTER to select the item.

NAVIGATION KEYS: If media is in activated MENU mode, the NAVI- GATION KEYS will be used to navigate Up, Down, Left, and Right within the menu. If display control menu is on, the NAVIGATION KEYS will be used to navigate Up, Down, Left, and Right within the menu. ENTER: In MENU mode, press the ENTER button to se- lect MENU items.

In the display menu, press the ENTER button to select items for modification, as per the on- screen instructions. MENU:

If the media is in PLAY mode and the MENU button is pressed, the DVD menu will appear on the screen. Use Navigation Keys to navigate within the menu, and use ENTER to select the item.

Press the MENU button again to return to PLAY mode. TITLE:

Press TITLE button to return the DVD media to the (cid:147)title(cid:148) of the DVD.

Press TITLE button again to return to the previous stop point and play. BACK:

Press the BACK button to exit the current active menu and return to the previous menu. SUBTITLE:

Press the SUBTITLE button to call up subtitle selection menu.

Repeatedly press the SUBTITLE button to cycle through each available subtitle.

Monitor, climate, audio, phone and voice recognition systems 4-89

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

c Do not use excessive force on the moni-

tor screen.

c Avoid touching or scratching the moni- tor screen as it may become dirty or damaged.

AUDIO:

Press the AUDIO button to call up audio menu.

Repeatedly press the AUDIO button to cycle through each available audio track. ANGLE:

Press the ANGLE button to call up camera angle menu.

Repeatedly press the ANGLE button to cycle through each available angle. CLEAR:

to expiration of

if actuated prior

Press the CLEAR button to clear all numeric inputs, the 3-second timer. NUMERIC KEYPAD (0(cid:150)9 & ‚10): Press the NUMERIC KEYPAD to directly access disc chapters, titles or tracks by inputting their numeric value. The (cid:147)‚10(cid:148) button input numbers greater than or equal to 10, allowing up three digits to be input for selecting chapter/title/track number.

The chapter/title/track number will be automati- cally selected (if valid, based on media content) if 3 seconds expire without any keypad inputs.

can

operator

The input chapter/title/track number by actuating the CLEAR control prior to the expiration of the 3-second timer.

cancel

the

These functions can be used only for the DVD discs which correspond to them. CARE AND MAINTENANCE Use a lightly dampened, lint free cloth to clean the surfaces of your NISSAN Mobile Entertainment System. (DVD player face, screen, remote con- trol, etc.)

Do not attempt to use the system in extreme temperature conditions [below -4(cid:176)F (-20(cid:176)C) or above 158(cid:176)F (70(cid:176)C)].

Do not attempt to operate the system in extreme humidity conditions (less than 10% or more than 75%).

CAUTION

The subsequent actuation of numeric buttons will continuously shift the previously input number to the (cid:147)left(cid:148).

c Do not use any solvents or cleaning solutions when cleaning the video system.

4-90 Monitor, climate, audio, phone and voice recognition systems

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

LHA0049

HOW TO HANDLE THE DVD

CAUTION

c Handle a DVD by its edges. Never touch

the surface of the disc.

c To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion.

c Do not use a conventional

record cleaner, benzine, thinner or alcohol in- tended for industrial use.

c A new disc may be rough on its inner and outer edges. Remove the rough edges using the side of a pen or pencil as illustrated.

c Never attempt to use a DVD that has been cracked, deformed, or repaired using adhesive. Doing so may cause damage to the equipment.

c Handle the DVD carefully to avoid contami- nation or flaws. Otherwise, signals may not be read properly.

c Do not write, draw or attach anything on any

side of the DVD.

c Do not store the DVD in locations with direct sunlight or in high temperatures or humidity. c Always place discs in the storage case when

they are not being used.

c Do not put on any sticker or write anything

on either surface of the DVD.

LHA0484

DVD player operation precautions Do not use the following DVDs as they may cause the DVD player to malfunction: c 3.1 in (8 cm) discs with an adapter

Monitor, climate, audio, phone and voice recognition systems 4-91

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

5. If the disc cannot be ejected see your NISSAN dealer for further assistance.

6. Re-program the radio presets.

c DVDs with a region code other than (cid:147)1(cid:148). The region code sA is displayed in a small symbol printed on the top of the DVD sB

c DVDs that are not round c DVDs with a paper label c DVDs that are warped, scratched, or

have unequal edges

c Recordable

digital

video

discs

(DVD+R)

c Rewritable (DVD+RW)

digital

video

discs

If a DVD with a paper label is used and becomes jammed you may be able to reset the unit and eject the jammed disc with the following procedure:

1. Record the radio presets. 2. Disconnect the negative terminal from

the battery for five minutes.

3. Reconnect the negative battery termi-

nal.

4. Check to see if the jammed DVD has been ejected. If it has not, try to eject the DVD by pushing the eject button.

LHA0318

Remote control and headphones battery replacement Replace the battery as follows:

1. Open the lid.

2. Replace batteries with new ones. c Size AA (remote control) c Size AAA (headphones) Make sure that the ends on the batteries match the markings inside the compartment.

and

3. Close the lid securely.

4-92 Monitor, climate, audio, phone and voice recognition systems

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

SAA0723
If the battery is removed for any reason other than replacement, close the lid se- curely. c If you will not be using the remote control for long periods of time, remove the batteries.

c Replacement of

the batteries is needed when the remote control only functions at extremely close distances to the DVD player or not at all.

c Be careful not to touch the battery terminal. c An improperly disposed battery can harm the environment. Always confirm local regu- lations for battery disposal.

c When changing batteries, do not let dust or oil get on the remote control and head- phones. FCC Notice: Changes or modifications not expressly ap- proved by the party responsible for compli- ance could void the user(cid:146)s authority to op- erate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210
of Industry Canada. Operation is subject to the following two conditions: (1) This de- vice may not cause harmful interference, and (2) this device must accept any inter- ference received, including interference that may cause undesired operation of the device.

CAR PHONE OR CB RADIO

When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following precautions, otherwise the new equipment may adversely affect the engine control system and other electronic parts.

WARNING

c A cellular telephone should not be used while driving so full attention may be given to vehicle operation. Some juris- dictions prohibit the use of cellular tele- phones while driving.

c If you must make a call while your ve- hicle is in motion, the hands free cellu- lar phone operational mode (if so equipped) is highly recommended. Ex- ercise extreme caution at all times so full attention may be given to vehicle operation.

c If a conversation in a moving vehicle requires you to take notes, pull off the road to a safe location and stop your vehicle before doing so.

Monitor, climate, audio, phone and voice recognition systems 4-93

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

CAUTION

c Keep the antenna as far away as pos- control

sible from the electronic modules.

c Keep the antenna wire more than 8 in (20 cm) away from the electronic con- trol system harnesses. Do not route the antenna wire next to any harness.

c Adjust the antenna standing-wave ratio as recommended by the manufacturer. c Connect the ground wire from the CB

radio chassis to the body.

c For details, consult a NISSAN dealer.

BLUETOOTHT HANDS-FREE PHONE SYSTEM WITHOUT NAVIGATION SYSTEM (if so equipped) WARNING

c Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation.

c If you are unable to devote full attention to vehicle operation while talking on the phone, pull off the road to a safe location and stop your vehicle before doing so.

CAUTION

To avoid discharging the vehicle battery, use a phone after starting the engine.

4-94 Monitor, climate, audio, phone and voice recognition systems

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

module when the ignition switch is placed in the ON position with the paired cellular phone turned on and carried in the vehicle. You can register up to 5 different BluetoothT cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time. Before using the BluetoothT Hands-Free Phone System, refer to the following notes. c Set up the wireless connection between a cellular phone and the in-vehicle phone module before using the hands-free phone system.

c Some BluetoothT enabled cellular phones may not be recognized by the in-vehicle phone visit www.nissanusa.com/bluetooth for a recom- mended phone list.

module.

Please

c You will not be able to use a hands-free

phone under the following conditions: (cid:150) Your vehicle is outside of the cellular ser-

vice area.

(cid:150) Your vehicle is in an area where it is difficult to receive a cellular signal; such as in a tunnel, in an underground parking garage, near a tall building or in a moun- tainous area.

Your NISSAN is equipped with the BluetoothT Hands-Free Phone System. If you are an owner of a BluetoothT enabled cellular phone, you can set up the wireless connection between your cellular phone and the in-vehicle phone module. With BluetoothT wireless technology, you can

WHA0975
make or receive a hands-free telephone call with your cellular phone in the vehicle.

Once your cellular phone is paired to the in- vehicle phone module, no other phone connect- ing procedure is required. Your phone is auto- matically connected with the in-vehicle phone

Monitor, climate, audio, phone and voice recognition systems 4-95

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

(cid:150) Your cellular phone is locked to prevent it

from being dialed.

c When the radio wave condition is not ideal or ambient sound is too loud, it may be difficult to hear the other person(cid:146)s voice dur- ing a call.

c Do not place the cellular phone in an area surrounded by metal or far away from the in-vehicle phone module to prevent tone quality degradation and wireless connection disruption.

c While a cellular phone is connected through the BluetoothT wireless connection, the bat- tery power of the cellular phone may dis- charge quicker than usual. The BluetoothT Hands-Free Phone System cannot charge cellular phones.

c If the hands-free phone system seems to be malfunctioning, please refer to (cid:147)Trouble- shooting guide(cid:148) later in this section. You can also visit www.nissanusa.com/bluetooth for troubleshooting help.

c Refer to the cellular phone Owner(cid:146)s Manual regarding the telephone charges, cellular phone antenna and body, etc.

not cause harmful interference, and (2) this device must accept any interference re- ceived, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation ex- posure limits set forth for an uncontrolled envi- ronment. This equipment should be installed and operated with minimum distance of 8 inches (20
cm) between the radiator and your body. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmit- ter. USING THE SYSTEM The NISSAN Voice Recognition system allows hands-free operation of the BluetoothT Phone System. If the vehicle is in motion, some commands may not be available so full attention may be given to vehicle operation. Initialization When the ignition switch is turned to the ON position, NISSAN Voice Recognition is initialized, which takes a few seconds. If the button is pressed before the initialization completes, the system will announce (cid:147)Hands-free phone system not ready(cid:148) and will not react to voice commands.

Operating tips To get the best performance out of the NISSAN Voice Recognition system, observe the following: c Keep the interior of the vehicle as quiet as possible. Close the windows to eliminate surrounding noises (traffic noises, vibration sounds, etc.), which may prevent the system from recognizing voice commands correctly. c Wait until the tone sounds before speaking a command. Otherwise, the command will not be received properly.

c Start speaking a command within 5 seconds

after the tone sounds.

c Speak in a natural voice without pausing

between words.

Giving voice commands To operate NISSAN Voice Recognition, press and release the button located on the steering wheel. After the tone sounds, speak a command. The command given is picked up by the micro- phone, and voice feedback is given when the command is accepted. c If you need to hear the available commands for the current menu again, say (cid:147)Help(cid:148) and the system will repeat them.

This device complies with Part 15 of the FCC Rules. Operation is subject to the fol- lowing two conditions: (1) this device may 4-96 Monitor, climate, audio, phone and voice recognition systems

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

c If a command is not recognized, the system announces, recognized. Please try again.(cid:148) Repeat the command in a clear voice.

(cid:147)Command not

c If you want to go back to the previous com- mand, you can say (cid:147)Go back(cid:148) or (cid:147)Correc- tion(cid:148) any time the system is waiting for a response.

c You can cancel a command when the sys- tem is waiting for a response by saying, (cid:147)Cancel(cid:148) or (cid:147)Quit.(cid:148) The system announces (cid:147)Cancel(cid:148) and ends the VR session. You can also press the button on the steering wheel at any time. Whenever the VR session is cancelled, a double beep is played to indicate you have exited the system.

c If you want to adjust the volume of the voice feedback, press the volume control switches (+ or -) on the steering wheel while being provided with feedback. You can also use the radio volume control knob.

c In most cases you can interrupt the voice feedback to speak the next command by pressing the button on the steering wheel.

rather than (cid:147)Phonebook.(cid:148) Wait for the voice feedback prompt then say (cid:147)New entry(cid:148).

How to say numbers

NISSAN Voice Recognition requires a certain way to speak numbers in voice commands. Refer to the following rules and examples. c Either (cid:147)zero(cid:148) or (cid:147)oh(cid:148) can be used for (cid:147)0(cid:148).

Example: 1-800-662-6200

(cid:150) (cid:147)One eight oh oh six six two six two oh

oh(cid:148), or

(cid:150) (cid:147)One eight zero zero six six two six two oh

oh(cid:148)

c Words can be used for the first 4 digits

places only.

Example: 1-800-662-6200

(cid:150) (cid:147)One eight hundred six six two six two oh

oh(cid:148),

(cid:150) NOT (cid:147)One eight hundred six six two sixty

two hundred, and

(cid:150) NOT (cid:147)One eight oh oh six six two sixty two

hundred.

c To speed the operation you can say multiple

commands. For example, press the button then say (cid:147)Phonebook, New entry(cid:148)

c Numbers can be spoken in small groups. The system will prompt you to continue en- tering digits, if desired.

Example: 1-800-662-6200
(cid:150) (cid:147)One eight oh oh(cid:148) The system repeats the numbers and prompts you to enter more. (cid:150) (cid:147)six six two(cid:148) The system repeats the numbers and prompts you to enter more. (cid:150) (cid:147)six two oh oh(cid:148)

c You can say (cid:147)Star(cid:148) for * and (cid:147)Pound(cid:148) for # at any time in any position of the phone num- ber. Example: 1-555-1212 *123
(cid:150) (cid:147)One five five five one two one two star

one two three(cid:148)

NOTE: For best results, say phone numbers as single digits.

Monitor, climate, audio, phone and voice recognition systems 4-97

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

PHONE/END Press the session or end a call.

button to cancel a VR

GETTING STARTED The following procedures will help you get started using the BluetoothT Hands-Free Phone System with NISSAN Voice Recognition. For ad- ditional command options, refer to (cid:147)List of voice commands(cid:148) later in this section. Choosing a language You can interact with the BluetoothT Hands-Free Phone System using English, Spanish or French.

To change the language, perform the following.

1. Press and hold the

than 5 seconds.

button for more

4. The system announces the current language and gives you the option to change the lan- guage to Spanish (in Spanish) or French (in French). Use the following chart to select the language.

NOTE:

Note: You must press the the change the language.

button or button within 5 seconds to

Current language

English Spanish French

Press

(PHONE/SEND)

Press (PHONE/END)

to select Spanish English English

to select French French Spanish

2. The

system announces:

the (cid:147)Press PHONE/SEND ( the ) button for hands-free phone system to enter the speaker adaptation mode or press the PHONE/END ( ) button to select a dif- ferent language.(cid:148)

3. Press the

button.

For information on speaker adaptation, see (cid:147)Speaker adaptation (SA) mode(cid:148) later in this section.

WHA0976

CONTROL BUTTONS The control buttons for the BluetoothT Hands- Free Phone System are located on the steering wheel.

PHONE/SEND Press the session or answer an incoming call.

button to initiate a VR

You can also use the button to skip through system feedback and to enter commands during a call. See (cid:147)List of voice commands(cid:148) and (cid:147)During a call(cid:148) later in this section for more information.

4-98 Monitor, climate, audio, phone and voice recognition systems

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/06/07—cathy X

5.

If you decide not to change the language, do not press either button. After 5 seconds, the VR session will end, and the language will not be changed. Pairing procedure

NOTE:

The pairing procedure must be performed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled.

Main Menu (cid:147)Setup(cid:148) sA

(cid:147)Pair phone(cid:148) sB

(cid:147)New phone(cid:148) sC

Initiate from handset sD

Name phone sE

Assign priority sF

Choose ringtone sG

1. Press the

button on the steering wheel. The system announces the available commands.

2. Say: (cid:147)Setup(cid:148) sA . The system acknowledges the command and announces the next set of available commands.

3. Say: (cid:147)Pair phone(cid:148) sB . The system acknowl- edges the command and announces the next set of available commands.

4. Say: (cid:147)New phone(cid:148) sC . The system acknowl- edges the command and asks you to initiate pairing from the phone handset sD . The pairing procedure of the cellular phone varies according to each cellular phone model. See the cellular phone Owner(cid:146)s Manual for details. You can also visit www.nissanusa.com/bluetooth for instruc- tions on pairing NISSAN recommended cel- lular phones.

When prompted for a PIN code, enter (cid:147)1234(cid:148) from the handset. The PIN code (cid:147)1234(cid:148) has been assigned by NISSAN and cannot be changed.

5. The system asks you to say a name for the

phone sE . If the name is too long or too short, the system tells you, then prompts you for a name again.

Also, if more than one phone is paired and the name sounds too much like a name already used, the system tells you, then prompts you for a name again.

6. The system asks you to assign a priority level sF . The priority level determines which phone is active when more than one paired BluetoothT phone is in the vehicle. Follow the instructions provided by the system or refer to (cid:147)Setup(cid:148) later in this section for more information on changing priorities.

7. The system will ask if you would like to select a custom ring tone sG . Follow the instruc- tions provided by the system or refer to (cid:147)Setup(cid:148) later in this section for more infor- mation on selecting ringtones.

Making a call by entering a phone number

Main Menu (cid:147)Call(cid:148) sA

Number (speak digits) sB

(cid:147)Dial(cid:148) sC

1. Press the

button on steering wheel. A

tone will sound.

2. Say: (cid:147)Call(cid:148) sA . The system acknowledges the command and announces the next set of available commands.

Monitor, climate, audio, phone and voice recognition systems 4-99

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

3. Say the number you wish to call sB . For example, 555-1212 can be said as (cid:147)five five five one two one two.(cid:148) See (cid:147)How to say numbers(cid:148) earlier in this section for more information.

4. When you have finished speaking the phone number, the system repeats it back and an- nounces the available commands.

5. Say: (cid:147)Dial(cid:148) sC . The system acknowledges

the command and makes the call.

For additional command options, see (cid:147)List of voice commands(cid:148) later in this section. Receiving a call When you hear the ring tone, press the button on the steering wheel. Once the call has ended, press the on the steering wheel.

button

NOTE: If you do not wish to take the call when you hear the ring tone, press the button on the steering wheel. For additional command options, see (cid:147)List of voice commands(cid:148) later in this section.

LIST OF VOICE COMMANDS

Main Menu

(cid:147)Call(cid:148) (cid:147)Phone Book(cid:148) (cid:147)Memo Pad(cid:148) (cid:147)Setup(cid:148)

When you press and release the button on the steering wheel, you can choose from the commands on the Main Menu. The following pages describe these commands and the com- mands in each sub-menu. Remember to wait for the tone before speaking. You can say (cid:147)Help(cid:148) to hear the list of commands currently available any time the system is waiting for a response. If you want to end an action without completing it, you can say (cid:147)Cancel(cid:148) or (cid:147)Quit(cid:148) at any time the system is waiting for a response. The system will end the VR session. Whenever the VR session is cancelled, a double beep is played to indicate you have exited the system. If you want to go back to the previous command, you can say (cid:147)Go back(cid:148) or (cid:147)Correction(cid:148) any time the system is waiting for a response.

When you get used to the menus in the system, you can talk ahead by saying more than one command at a time. For example, say, (cid:147)Call five five five one two one two(cid:148) or (cid:147)Memo pad record.(cid:148)

Also, when you get used to the system re- sponses, you can skip ahead to the tone by pressing the button on the steering wheel. However, if you press the button when the system is waiting for a response from you it will end the VR session. (cid:147)Call(cid:148)

Main Menu

(cid:147)Call(cid:148)

Name (speak name) sA Number (speak digits) sB (cid:147)Redial(cid:148) sC (cid:147)Call Back(cid:148) sD

Name (speak name) sA If you have stored entries in the Phone Book, you can dial a number associated with a name and location.

See (cid:147)Phone book(cid:148) later in this section to learn how to store entries.

4-100 Monitor, climate, audio, phone and voice recognition systems

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

When prompted by the system, say the name of the phone book entry you wish to call. The system acknowledges the name.

If there are multiple locations associated with the name, the system asks you to choose the loca- tion.

Once you have confirmed the name and location, the system begins the call. Number (speak digits) sB When prompted by the system, say the number you wish to call. Refer to (cid:147)How to say numbers(cid:148) and (cid:147)Making a call by entering a phone number(cid:148) earlier in this section for more details. (cid:147)Redial(cid:148) sC Use the Redial command to call the last number that was dialed within the vehicle.

NOTE:

The system will not redial the last number dialed by the handset keypad.

The system acknowledges the command, re- peats the number and begins dialing.

If a redial number does not exist, the system announces, (cid:147)There is no number to redial(cid:148) and ends the VR session.

(cid:147)Call back(cid:148) sD Use the Call Back command to dial the number of the last incoming call within the vehicle.

The system acknowledges the command, re- peats the number and begins dialing. If a call back number does not exist, the system announces, (cid:147)There is no number to call back(cid:148) and ends the VR session. During a call During a call there are several command options available. Press the button on the steering wheel to mute the receiving voice and enter com- mands. c (cid:147)Help(cid:148) (cid:151) The system announces the avail-

able commands.

c (cid:147)Go back/Correction(cid:148) (cid:151) The system an- nounces (cid:147)Go back,(cid:148) ends the VR session and returns to the call.

c (cid:147)Cancel/Quit(cid:148) (cid:151) The system announces (cid:147)Cancel,(cid:148) ends the VR session and returns to the call.

c (cid:147)Send/Enter/Call/Dial(cid:148) (cid:151) Use the Send command to enter numbers during a call. For example, if you were directed to dial an ex- tension by an automated system: Say: (cid:147)Send one two three four.(cid:148)

The system acknowledges the command and sends the tones associated with the numbers. The system then ends the VR ses- sion and returns to the call.

c (cid:147)Transfer call(cid:148) (cid:151) Use the Transfer Call com- mand to transfer the call from the BluetoothT Hands-Free Phone System to the cellular phone when privacy is desired. The system announces, (cid:147)Transfer call. Call transferred to privacy mode.(cid:148) The system then ends the VR session. You can also issue the Transfer Call com- mand again to return to a hands-free call through the vehicle.

c (cid:147)Mute(cid:148) (cid:151) Use the Mute command to mute your voice so the other party cannot hear it. Use the mute command again to unmute your voice.

NOTE: If a call is ended or the cellular phone network connection is lost while the Mute feature is on, the Mute feature will be reset to (cid:147)off(cid:148) for the next call so the other party can hear your voice.

Monitor, climate, audio, phone and voice recognition systems 4-101

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

(cid:147)Phone book(cid:148)

NOTE:

Phone book commands are not available when the vehicle is moving.

Main Menu

(cid:147)Phone Book(cid:148)

(cid:147)New Entry(cid:148) sA (cid:147)Edit(cid:148) sB (cid:147)Delete(cid:148) sC 9List Names(cid:148) sD

The Phone Book stores up to 40 names for each phone paired with the system. Each name can have up to 4 locations/phone numbers associ- ated with it.

NOTE:

Each phone has its own separate phone book. You cannot access Phone A(cid:146)s phone book if you are currently connected with Phone B. (cid:147)New entry(cid:148) sA Use the New Entry command to store a new name in the system.

When prompted by the system, say the name you would like to give the new entry. For example, say: (cid:147)Mary.(cid:148)

If the name is too long or too short, the system tells you, then prompts you for a name again.

Also, if the name sounds too much like a name already stored, the system tells you, then prompts you for a name again.

Once the system accepts the name and you confirm it is correct, the system asks for a location (Home, Office, Mobile or Other). For example, say: (cid:147)Home.(cid:148)

The system acknowledges the location.

The system will ask you to say a phone number or to transfer a phone number stored in the cellular phone(cid:146)s memory.

Enter a phone number by voice command:

For example, say: (cid:147)five five five one two one two. (cid:148) See (cid:147)How to say numbers(cid:148) earlier in this section for more information.

To transfer a phone number stored in the cellular phone(cid:146)s memory: Say 9Transfer entry.9 The system acknowledges the command and asks you to initiate the transfer from the phone handset. The new contact phone

number will be transferred from the cellular phone via the BluetoothT communication link. The transfer procedure varies according to each cellular phone. See the cellular phone Owner(cid:146)s Manual can visit also www.nissanusa.com/bluetooth for instructions on transferring phone numbers from NISSAN recommended cellular phones.

for details. You

The system repeats the number and prompts you for the next command. When you have finished entering numbers or transferring an entry, choose (cid:147)Store.(cid:148)

The system confirms the name, location and number. The system then asks if you would like to store another location for the same name. If you do not wish to store another location, the system ends the VR session. (cid:147)Edit(cid:148) sB Use the Edit command to alter an existing phone book entry or to add a 2nd, 3rd or 4th phone number to an existing entry.

When prompted by the system, say the name of the entry you wish to edit.

The system acknowledges the name and asks you for the location you would like to edit. Say the name of the location.

4-102 Monitor, climate, audio, phone and voice recognition systems

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

The system acknowledges the location.

The system will ask you to say a phone number or to transfer a phone number stored in the cellular phone(cid:146)s memory.

Enter a phone number by voice command: For example, say: (cid:147)five five five one two one two. (cid:148) See (cid:147)How to say numbers(cid:148) earlier in this section for more information. To transfer a phone number stored in the cellular phone(cid:146)s memory: Say 9Transfer entry.9 The system acknowledges the command and asks you to initiate the transfer from the phone handset. The new contact phone number will be transferred from the cellular phone via the BluetoothT communication link. The transfer procedure varies according to each cellular phone. See the cellular phone Owner(cid:146)s Manual can visit also www.nissanusa.com/bluetooth for instructions on transferring phone numbers from NISSAN recommended cellular phones. The system repeats the number and prompts you for the next command. When you have finished entering numbers, choose (cid:147)Store.(cid:148) The system confirms the name, location and number, then announces that the entry has been stored. The system then ends the VR session.

for details. You

(cid:147)Delete(cid:148) sC Use the Delete command to erase one entry from the phone book, all entries from the phone book, the current redial number or the current call back number.

To delete entries from the phone book, say a name or (cid:147)All entries(cid:148) when prompted by the sys- tem.

The system acknowledges the command and asks you to confirm the deletion.

To delete the current redial number or call back number, say (cid:147)redial number(cid:148) or (cid:147)call back num- ber(cid:148) when prompted by the system.

If a redial number or a call back number exists, the system deletes them without asking for confirma- tion. If there is no number for the entry you are trying to delete, the system says so and ends the VR session. (cid:147)List names(cid:148) sD Use the List Names command to hear all the names and locations in the phone book. The system recites the phone book entries but does not include the actual phone numbers. When the playback of the list is complete, the system goes back to the main menu.

You can stop the playback of the list at any time button on the steering by pressing the wheel. The system ends the VR session. (cid:147)Memo pad(cid:148)

Main Menu

(cid:147)Memo Pad(cid:148)

(cid:147)Record(cid:148) sA (cid:147)Play(cid:148) sB (cid:147)Delete(cid:148) sC

The Memo Pad records a maximum of 3 voice memos, each up to 20 seconds long. (cid:147)Record(cid:148) sA The system announces (cid:147)Recording(cid:148) and a tone sounds, signaling you to begin.

Speak the information you wish to record clearly. When you are done, press the button on the steering wheel.

or

A tone sounds and the system announces (cid:147)Memo recorded.(cid:148) Another tone sounds to end the VR session.

If the memo pad is full, the system asks if you wish to record over the oldest memo.

Monitor, climate, audio, phone and voice recognition systems 4-103

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

(cid:147)Play(cid:148) sB The system plays back all the memos in the order of newest to oldest. The system ends the VR session.

If there are no memos recorded, the system an- nounces (cid:147)No messages to play.(cid:148) The system ends the VR session. (cid:147)Delete(cid:148) sC The Delete command erases all memos. The system asks you to confirm this action before deleting all memos. (cid:147)Setup(cid:148)

Main Menu

(cid:147)Setup(cid:148)

(cid:147)Pair Phone(cid:148) sA (cid:147)List Phone(cid:148) sB (cid:147)Select Phone(cid:148) sC (cid:147)Change Priority(cid:148) sD (cid:147)Delete Phone(cid:148) sE (cid:147)Select Ringtone(cid:148) sF (cid:147)Bluetooth Off(cid:148) sG

Use the Setup command to change options as- sociated with the BluetoothT Hands-Free Phone System. (cid:147)Pair phone(cid:148) sA Use the Pair Phone command to pair a phone to the BluetoothT Hands-Free Phone System.

NOTE:

The pairing procedure must be performed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled. Also, see (cid:147)Pairing procedure(cid:148) earlier in this section for additional information.

Up to 5 phones can be paired. If you try to pair a sixth phone, the system announces that you must first delete one phone or replace an existing phone.

If you try to pair a phone that has already been paired to your vehicle(cid:146)s system, the system an- nounces the name the phone is already using. The pairing procedure will then be cancelled.

When prompted by the system, choose from the following commands: c (cid:147)New phone(cid:148) (cid:151) Refer to (cid:147)Pairing a phone(cid:148)

earlier in this section.

c (cid:147)Replace phone(cid:148) (cid:151) The system announces the names of the phones already paired and asks which you would like to replace.

Once you say the name of the phone you wish to replace, the pairing procedure will begin. Refer to (cid:147)Pairing procedure(cid:148) earlier in this section.

the system announces,

c (cid:147)List phone(cid:148) (cid:150) See the description below. (cid:147)List phone(cid:148) sB Use the List Phone command to hear the names of the phones currently paired. If no phones are paired, (cid:147)No paired phones to list.(cid:148) The system then ends the VR session. (cid:147)Select phone(cid:148) sC Use the Select Phone command to select a phone of lesser priority when two or more phones paired with BluetoothT Hands-Free Phone Sys- tem are in the vehicle at the same time.

The system asks you to name the phone and confirm the selection.

Once the selection is confirmed, the selected phone remains active until the ignition switch is turned OFF or you select a new phone.

4-104 Monitor, climate, audio, phone and voice recognition systems

Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X

(cid:147)Change priority(cid:148) sD Use the Change Priority command to change the priority level of the active phone.

The priority level determines which phone is ac- tive when more than one paired BluetoothT phone is in the vehicle.

The system states the priority level of the active phone and asks for a new priority level (1, 2, 3, 4, 5).

If the new priority level is already being used for