Download PDF Manual


CAUTION


쐌 If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.


쐌 Tighten until the fuel-filler cap clicks. Failure to tighten the fuel-filler cap mal- properly may cause the function indicator lamp (MIL) to illu- lamp illuminates minate. If the because the fuel-filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The lamp should turn off after a few lamp does


driving trips. If the


墌 05.10.18/Z33-D/V5.0 墍


STEERING WHEEL


SUN VISORS


1. To block out glare from the front, swing down


the main sun visor 쎻1 .


2. To block glare from the side, remove the main sun visor from the center mount and swing it to the side 쎻2 .


3. To use the extension sun visor 쎻3


(if so equipped), pull it out from the main sun visor as shown.


SPA1510


TILT OPERATION Push the lock lever down and adjust the steering wheel up or down to the desired position. Push the lock lever up securely to lock the steering wheel in place.


WARNING


Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.


CAUTION


Do not store the main sun visor before storing the extension sun visor.


SPA2176


Pre-driving checks and adjustments 3-25


墌 05.10.18/Z33-D/V5.0 墍


MIRRORS


SPA1792


INSIDE MIRROR Adjust the height and the angle of the inside mirror to the desired position.


SPA2143
The night position 쎻1 will reduce glare from the headlights of vehicles behind you at night. Use the day position 쎻2 when driving in daylight hours.


WARNING


Use the night position only when neces- sary, because it reduces rear view clar- ity.


SPA2157


AUTOMATIC ANTI-GLARE INSIDE MIRROR (if so equipped) The inside mirror is designed so that it automati- cally changes reflection according to the inten- sity of the headlight of the following vehicle.


When the inside mirror is in the “I” (AUTO) position 쎻1 , excessive glare from the headlights of the vehicle behind you will be reduced. The AUTO indicator light 쎻A (green) will be on. When the switch of the inside mirror is in the “쎻” (OFF) position 쎻2 , the inside mirror will operate normally.


For HomeLink Universal Transceiver, see the


3-26 Pre-driving checks and adjustments


墌 05.10.18/Z33-D/V5.0 墍


description in the “2. Instruments and controls” section.


The outside mirror will operate only when the ignition switch is in the ACC or ON position. Turn the control knob (located on the driver side door armrest) to right or left to select the right or left outside mirror, then adjust using the knob.


SPA1390


OUTSIDE MIRRORS


WARNING


Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects.


Pre-driving checks and adjustments 3-27


墌 05.10.18/Z33-D/V5.0 墍


IC0565


Foldable outside mirrors Fold the outside mirror by pushing it toward the rear of the vehicle.


3-28 Pre-driving checks and adjustments


墌 05.10.18/Z33-D/V5.0 墍


4 Display screen, heater, air conditioner and


audio systems


Safety note .............................................................................. 4-2
Control panel buttons — with navigation system.......... 4-2
Names of the components ............................................ 4-2
How to use joystick and “ENTER” button................. 4-3
How to use “BACK” button .......................................... 4-3
Setting up the start-up screen ..................................... 4-3
How to use “INFO” button............................................ 4-3
How to use “SETTING” button .................................... 4-5
” button.................................... 4-8
How to use the “ Ventilators ............................................................................... 4-8
Center ventilators ............................................................ 4-8
Side ventilators ................................................................ 4-8
Heater and air conditioner (Automatic) .......................... 4-9
Automatic operation .................................................... 4-10
Manual operation .......................................................... 4-10
Operating tips ............................................................... 4-11


Servicing air conditioner .................................................. 4-12
Audio system ....................................................................... 4-12
Radio ............................................................................... 4-12
FM radio reception ...................................................... 4-13
AM radio reception ...................................................... 4-13
Satellite (SAT) radio reception (if so equipped) ............................................................ 4-13
Audio operation precautions ..................................... 4-13
FM-AM radio with compact disc (CD) player ...... 4-19
FM-AM-SAT radio with compact disc (CD) changer ........................................................................... 4-23
CD care and cleaning ................................................. 4-29
Steering wheel switch for audio control (if so equipped)......................................................................... 4-29
Antenna ........................................................................... 4-30
Car phone or CB radio .................................................... 4-30


墌 05.10.18/Z33-D/V5.0 墍


SAFETY NOTE


CONTROL PANEL BUTTONS — WITH NAVIGATION SYSTEM


WARNING


쐌 Positioning of the heating or air con- ditioning controls and display con- trols should not be done while driv- ing, in order that full attention may be given to driving operation.


쐌 Do not disassemble or modify this system. If you do, it may result in accidents, fire, or electric shock.


쐌 Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in acci- dent, fire or electric shock.


쐌 In case you notice any foreign object in the system hardware, spill liquid on it, or notice smoke or smell com- ing from it, stop using the system immediately and contact a NISSAN dealer. Ignoring such conditions may lead to accidents, fire, or electric shock.


When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start. Reference symbols: “ENTER” button This is a button on the control panel. “Display” key This is a select key on the screen. By selecting this key you can proceed to the next function.


SAA1289


NAMES OF THE COMPONENTS 1. JOYSTICK and “ENTER” button 2. “INFO” button 3. “SETTING” button 4. “BACK” button 5. “ For Navigation System control buttons (other than above), refer to the separate Navigation System Owner’s Manual.


” brightness control button


4-2 Display screen, heater, air conditioner and audio systems


墌 05.10.18/Z33-D/V5.0 墍


HOW TO USE JOYSTICK AND “ENTER” BUTTON Choose an item on the display using the joystick and push the ENTER button for operation. HOW TO USE “BACK” BUTTON This button has two functions. To return to the previous screen: When this button is pushed during setup, setup will be canceled, and the screen will return to the previous screen. To finish the set-up: When this button is pushed after setup is com- pleted, the settings will be renewed as directed, and the screen will return to the map. INFO: When the “BACK” button must be pushed, (for example, after the setup is finished) instructions are given in the operation procedure of each section in this manual. If the “BACK” button is pushed when not finished with the setup, the setting will be canceled, and the screen will return to the previous screen.


SETTING UP THE START-UP SCREEN When you turn the ignition key to the ACC position, the SYSTEM START-UP warning is displayed on the screen. Read the warning and select the “OK” key then push the “ENTER” button. If you do not push the ENTER button, this system will not proceed to the next step display. To proceed to the next step, refer to the separate Navigation System Owner’s Manual.


SAA1290


HOW TO USE “INFO” BUTTON When the “INFO” button is pushed, the “Main- tenance” screen will be displayed. Maintenance information To set the maintenance interval for the Engine Oil or Oil Filter, choose an item using the joystick and push the “ENTER” button.


You can also set to display a message to remind you that the maintenance needs to be per- formed.


The following example shows how to set the engine oil change interval. Use the same steps Display screen, heater, air conditioner and audio systems 4-3


墌 05.10.18/Z33-D/V5.0 墍


to set the other maintenance information.


“Maintenance” display cannot be operated when the vehicle is moving. Stop the vehicle in a safe place to see the information.


SAA1291


1. Reset the driving distance to the new main-


tenance schedule.


2. Set the interval (mileage) of the maintenance schedule. To determine the recommended maintenance interval, refer to your “NISSAN Service and Maintenance Guide”.


3. To display the MAINTENANCE INFORMA- TION automatically when the set trip distance the “Interval Re- is reached, highlight minder” key with the joystick and push the “ENTER” button.


4. To return the display to the “Maintenance”


screen, push the “BACK” button.


4-4 Display screen, heater, air conditioner and audio systems


墌 05.10.18/Z33-D/V5.0 墍


Engine Oil 쎻1 /Oil Filter 쎻2


The “Maintenance Notice” screen displays each time the ignition switch is turned ON until one of the following conditions are met: 쐌 “Reset Distance” is selected. 쐌 “Interval Reminder” is set OFF. 쐌 the maintenance interval is set again.


SAA1292


SAA1293


to the separate Navigation System


*: Refer Owner’s Manual. HOW TO USE “SETTING” BUTTON The “Settings” screen will appear when the “SETTING” button is pushed.


SAA1332


Maintenance notice The “Maintenance Notice” screen (“ENGINE OIL” or “OIL FILTER”) will be automatically displayed as shown when both of the following conditions are met: 쐌 the vehicle is driven the set distance and the


ignition switch is turned OFF.


쐌 the ignition switch is turned ON the next time


the vehicle will be driven.


To return to the previous display after the “Maintenance Notice” screen is displayed, push the “BACK” button.


Display screen, heater, air conditioner and audio systems 4-5


墌 05.10.18/Z33-D/V5.0 墍


and turn on the “ON” indicator. Brightness/Contrast/Background Color: To adjust the brightness and contrast of the screen, select the “Brightness” or “Contrast” key and push the “ENTER” button. Then you can adjust the brightness to darker or brighter and the contrast to lower or higher using the joystick. For information on the “Background Color” key, refer to the separate Navigation System Owner’s Manual.


SAA1294


Display settings The following menu will appear when pushing the “SETTING” button, selecting “Display” key and pushing the “ENTER” button. Display:


To turn off the screen, select the “Display” key and push the “ENTER” button to turn off the “ON” indicator. When any mode button is pushed with the screen off, the screen turns on for further operation. The screen will turn off automatically 5 seconds after the operation is finished on the map display. To turn on the screen, select the “Display” key 4-6 Display screen, heater, air conditioner and audio systems


SAA1091


Clock settings The following display will appear when pushing the “SETTING” button, selecting the “Clock” key and pushing the “ENTER” button. On-screen Clock: When this item is turned to ON, a clock is always displayed in the upper right corner of the screen. indicate the time almost exactly This clock will because it is always adjusted by the GPS system.


墌 05.10.18/Z33-D/V5.0 墍


Clock Format: Choose either the 12-hour clock display or the 24-hour clock display. Offset Adjust: Adjust the time by increasing or decreasing per minute. Daylight Saving Time: Turn this item to ON for daylight saving time application. Time Zone: Choose the time zone from the following 쐌 Pacific 쐌 Mountain 쐌 Central 쐌 Eastern 쐌 Atlantic 쐌 Newfoundland


SAA1295


Language/Units settings The Language/Units settings screen will appear when selecting the “Language/Units” key and pushing the “ENTER” button.


SAA1296


Display of Select Language


the “Select Language” or “Select


Select Units” key and push the “ENTER” button. Language: “English” or “Français” Unit: “US” — Mile, °F, MPG


“Metric” — km, °C, L/100 km


Select the “ON” key of the desired language or units and push the “ENTER” button.


Display screen, heater, air conditioner and audio systems 4-7


墌 05.10.18/Z33-D/V5.0 墍


VENTILATORS



HOW TO USE THE “ BUTTON To change the display brightness, push the “ ” (DAY/NIGHT) button. Pushing the but- ton again will change the display to DAY or NIGHT display. Then, adjust the brightness mov- ing the joystick right or left. If no operation is done within 10 seconds, or if the “BACK” button is pushed, the display will return to the previous display.


SAA0600


SAA0601


CENTER VENTILATORS Adjust the air flow direction of ventilators. Moving the lever up or down will open 쎻A or close 쎻B the vents. To change the air flow direction, turn the dial 쎻C .


SIDE VENTILATORS Adjust the air flow direction of ventilators by 쎻A opening, 쎻B closing or 쎻C rotating as illustrated.


4-8 Display screen, heater, air conditioner and audio systems


墌 05.10.18/Z33-D/V5.0 墍


HEATER AND AIR CONDITIONER (Automatic)


1. Air flow control dial 2. Temperature control dial* * The display of degrees:


“60-75-90” is used for °F (US). “18-25-32” is used for °C (Canada).


3. Fan speed control dial 4. Rear window defroster button


(See the “2. Instruments and controls” sec- tion.)


5. Air intake button


(Air recirculation and Fresh air)


6. A/C (air conditioner) button


SAA1297


WARNING


쐌 The air conditioner cooling function operates only when the engine is running.


쐌 On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or animals. Do not leave children or adults who would normally require


the assistance of others in your ve- hicle. Unattended pets should also not be left alone.


쐌 Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.


쐌 Positioning of the heater or air con- ditioner controls should not be done while driving, so full attention may be given to vehicle operation.


Start the engine and operate the controls to activate the air conditioner. NOTE: In your vehicle, the air conditioner system is designed to automatically activate the cooling function when operating the air flow control dial, the fan speed control dial or the air intake button. (The indicator light on the A/C button will illumi- nate.) Push the A/C button off when the cooling function is not necessary.


Display screen, heater, air conditioner and audio systems 4-9


墌 05.10.18/Z33-D/V5.0 墍


AUTOMATIC OPERATION Cooling and/or dehumidified heating (AUTO) This mode may be normally used all year round as the system automatically works to keep a constant temperature. Air flow distribution and fan speed are also controlled automatically.


1. Turn the fan speed control dial and air flow control dial to the AUTO position. The air conditioner will automatically turn on. (The A/C button indicator light illuminates.)


2. Turn the temperature control dial to set the


desired temperature.


쐌 Adjust the temperature to about 75°F (24°C)


for normal operation.


쐌 The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution and fan speed are also con- trolled automatically.


Heating (AUTO; A/C off) The air conditioner does not activate. When you need to heat only, use this mode. 1. Turn the fan speed control dial and air flow control dial to the AUTO position. (The air conditioner will turn on.)


2. Push the A/C button to turn off


the air conditioner. (The A/C button indicator light will turn off.)


3. Turn the temperature control dial to set the


desired temperature.


쐌 The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution and fan speed are also con- trolled automatically.


쐌 Do not set the temperature lower than the outside air temperature. Otherwise the sys- tem may not work properly.


쐌 Not recommended if windows fog up. Dehumidified defrosting or defogging 1. Turn the fan speed control dial to the desired


position.


2. Turn the air flow control dial to the DEF


position.


3. Turn the temperature control dial to set the


desired temperature.


쐌 To quickly remove ice from the outside of the windows, turn the fan speed control dial to the maximum position.


쐌 As soon as possible after the windshield is clean, turn the air flow control dial to the AUTO position to return to the auto mode.


4-10 Display screen, heater, air conditioner and audio systems


or


position,


쐌 When the air flow control dial is turned to the the air conditioner will automatically be turned on at outside temperatures above 23°F (−5°C) to defog the windshield, and the air recirculation mode will automatically be turned off. Outside air is drawn into the passenger compartment to improve the defogging per- formance.


MANUAL OPERATION Fan speed control Turn the fan speed control dial control the fan speed. Turn the dial to the AUTO position to return to automatic control of the fan speed. Air recirculation/Fresh air Each time the air intake button is pushed, the indicator light on the button will alternate


to manually


(Air recirculation) and


(Fresh air).


indicator light is on, the interior When the air is recirculated. (When the air recirculation mode is selected with the A/C indicator off while the fan speed control dial is in the AUTO position, the air conditioner will turn on.) When the air is drawn into the passenger compartment.


indicator light is on, the outside


墌 05.10.18/Z33-D/V5.0 墍


쐌 When the air intake button is pushed for longer than 1.5 seconds, both indicator lights ) will flash twice, and then the intake air will be controlled automatically. During this AUTO mode, the indicator light of the currently selected mode illuminates.


and


쐌 When the air


or


flow control dial is in the position, the air recirculation


mode does not activate.


OPERATING TIPS When the engine coolant temperature and out- side air temperature are low, the air flow from the foot outlets may not operate for a maximum of 150 seconds. However, this is not a malfunction. After the coolant temperature warms up, the air flow from the foot outlets will operate normally.


Air flow control Turning the air flow control dial selects the air outlet to:


: Air flows from center and side ventila-


tors.


: Air flows from center and side ventila-


tors and foot outlets.


: Air flows mainly from foot outlets. : Air flows from defroster and foot out-


lets.


: Air flows mainly from defroster outlets.


To turn the system off Turn the fan speed control dial position.


to the OFF


SAA0603
Sensor 쎻A on the instrument panel helps main- tain a constant temperature; do not put anything on or around this sensor.


Display screen, heater, air conditioner and audio systems 4-11


墌 05.10.18/Z33-D/V5.0 墍


do not indicate any malfunction in your radio system. Remember that a moving vehicle is not the ideal place to listen to a radio. Because of the move- ment, reception conditions will constantly change. Buildings, terrain, signal distance and interference from other vehicles can work against ideal reception. Described below are some of the factors that can affect your radio reception.


SERVICING AIR CONDITIONER


AUDIO SYSTEM


The air conditioning system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. This refrigerant will not harm the earth’s ozone layer. How- ever, special charging equipment and lubricant are required when servicing your NISSAN air conditioner. Using improper refrigerants or lubri- cants will cause severe damage to your air conditioning system. See “Capacities and rec- ommended fuel/lubricants” in the “9. Technical and consumer information” section for air con- ditioning system refrigerant and lubricant recom- mendations.


A NISSAN dealer will be able to service your environmentally friendly air conditioning system.


WARNING


The air conditioner system contains re- frigerant under high pressure. To avoid personal injury, any air conditioner ser- vice should be done only by an experi- enced technician with proper equip- ment.


RADIO Turn the ignition key to ACC or ON and press the POWER, FM or AM button to turn on the radio. If you listen to the radio with the engine not running, the key should be turned to the ACC position.


Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external in- fluences. Intermittent changes in reception qual- ity normally are caused by these external influences. Using a cellular phone in or near the ve- hicle may influence radio reception quality. Radio reception Your radio system is equipped with state-of-the- art electronic circuits to enhance radio recep- tion. These circuits are designed to extend re- ception range, and to enhance the quality of that reception.


However there are some general characteristics of FM, AM and SAT (satellite — if so equipped) radio signals that can affect radio reception quality in a moving vehicle, even when the finest equipment is used. These characteristics are completely normal in a given reception area, and


4-12 Display screen, heater, air conditioner and audio systems


墌 05.10.18/Z33-D/V5.0 墍


a station transmitter, the signals will tend to fade and/or drift.


Static and flutter: During signal interference from buildings, large hills or due to antenna position, usually in conjunction with increased distance from the station transmitter, static or flutter can be heard. This can be reduced by adjusting the treble control counterclockwise to reduce treble response. Multipath reception: Because of the reflective characteristics of FM signals, direct and re- flected signals reach the receiver at the same time. The signals may cancel each other, result- ing in momentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics. AM signals are also sub- ject to interference as they travel from transmitter to receiver. Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for several seconds during ionospheric turbulence even in areas where no obstacles exist. Static: Caused by thunderstorms, electrical


power lines, electric signs and even traffic lights. SATELLITE (SAT) RADIO RECEPTION (if so equipped) When the satellite radio is first installed or the battery has been replaced, the satellite radio may not work properly. This is not a malfunction. Wait more than 10 minutes with the satellite radio ON for the satellite radio to receive all of the necessary data. No satellite radio reception is available when the SAT band option is selected unless optional satellite receiver and antenna are installed, and an XM® or SIRIUSTM satellite radio service subscription is active. Satellite radio performance may be affected if cargo carried on the roof blocks the satellite radio signal. If possible, do not put cargo over the satellite antenna. Satellite radio is not available in Alaska and Hawaii. AUDIO OPERATION PRECAUTIONS Compact Disc (CD) player 쐌 During cold weather or rainy days, the player may malfunction due to the hu- midity. If this occurs, remove the CD and Display screen, heater, air conditioner and audio systems 4-13


墌 05.10.18/Z33-D/V5.0 墍


SAA0306


FM RADIO RECEPTION Range: FM range is normally limited to 25 to 30
miles (40 to 48 km), with monaural (single channel) FM having slightly more range than stereo FM. External influences may sometimes interfere with FM station reception even if the FM station is within 25 miles (40 km). The strength of the FM signal is directly related to the distance between the transmitter and receiver. FM signals follow a line-of-sight path, exhibiting many of the same characteristics as light. For example they will reflect off objects.


Fade and drift: As your vehicle moves away from


dehumidify or ventilate the player com- pletely.


쐌 The player may skip while driving on


rough roads.


쐌 The CD player sometimes cannot func- tion when the passenger compartment temperature is extremely high. De- crease the temperature before use.


SAA0480
쐌 Only use high quality 4.7 inches (12 cm) round discs that have the “COMPACT disc DIGITAL AUDIO” logo on the disc or packaging.


쐌 Do not expose the CD to direct sunlight.


4-14 Display screen, heater, air conditioner and audio systems


쐌 CDs that are of poor quality, dirty, scratched, covered with fingerprints, or that have pin holes may not work prop- erly.


쐌 The following CDs may not work prop-


erly: 쐌 Copy control compact discs (CCCD) 쐌 Recordable compact discs (CD-R) 쐌 Rewritable compact discs (CD-RW)


쐌 Do not use the following CDs as they may cause the CD player to malfunction. 쐌 3.1 in (8 cm) discs 쐌 CDs that are not round 쐌 CDs with a paper label 쐌 CDs that are warped, scratched, or


have abnormal edges


쐌 This audio system can only play prere- corded CDs. CDs with MP3 or WMA format cannot be written in this audio system.


쐌 If the CD cannot be played, one of the following messages will be displayed.


墌 05.10.18/Z33-D/V5.0 墍


session, and writing more than once is called a multisession.


쐌 ID3/WMA Tag — The ID3/WMA tag is the part of the encoded MP3 or WMA file that contains information about the digital music file such as song title, artist, album title, encoding bit rate, track time duration, etc. ID3 tag information is displayed on the Album/Artist/Track title line on the display.


* Windows and Windows Media are either registered trademarks and trademarks of Mi- crosoft Corporation in the United States and/or other countries.


CHECK DISC: 쐌 Confirm that the CD is inserted cor- rectly (the label side is facing up, etc.).


쐌 Confirm that the CD is not bent or


warped and it is free of scratches.


PUSH EJECT: This is a malfunction due to excessive temperature inside the player. Remove the CD by pushing the EJECT button. After a short time, reinsert the CD. The CD can be played when the temperature of the player returns to normal. UNPLAYABLE: The file is unplayable in this audio sys- tem (only MP3 or WMA CD in the audio system with a CD changer).


Compact Disc (CD) with MP3 or WMA (for the audio system with a 6CD changer) Explanation of terms: 쐌 MP3 — MP3 is short for Moving Pictures Experts Group Audio Layer 3. MP3 is the most well-known compressed digital audio file format. This format allows for near “CD quality” sound, but at a fraction of the size of


normal audio files. MP3 conversion of an audio track from CD-ROM can reduce the file size by approximately 10:1 ratio (Sampling: 44.1 kHz, Bit rate: 128 kbps) with virtually no perceptible loss in quality. MP3 compression removes the redundant and irrelevant parts of a sound signal that the human ear doesn’t hear.


쐌 WMA — Windows Media Audio (WMA) is a compressed audio format created by Mi- crosoft as an alternative to MP3. The WMA codec offers greater file compression than the MP3 codec, enabling storage of more digital audio tracks in the same amount of space when compared to MP3s at the same level of quality.


쐌 Bit rate — Bit rate denotes the number of bits per second used by a digital music file. The size and quality of a compressed digital audio file is determined by the bit rate used when encoding the file.


쐌 Sampling frequency — Sampling frequency is the rate at which the samples of a signal are converted from analog to digital (A/D conver- sion) per second.


쐌 Multisession — Multisession is one of the methods for writing data to media. Writing data once to the media is called a single


Display screen, heater, air conditioner and audio systems 4-15


墌 05.10.18/Z33-D/V5.0 墍


쐌 If there is a file in the top level of the disc,


“ROOT” is displayed.


쐌 The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.


Playback order:


SAA1025


Playback order of the CD with compressed files (MP3/WMA) is as illustrated above. 쐌 The


containing MP3/WMA files are not shown in the display.


names of


folders


not


4-16 Display screen, heater, air conditioner and audio systems


墌 05.10.18/Z33-D/V5.0 墍


Specification chart:


Supported media


Supported file systems


CD, CD-R, CD-RW


ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not sup- ported.


Version


MPEG1, MPEG2, MPEG2.5


MP3


Sampling frequency


8 kHz - 48 kHz


Supported ver- sions*1


Bit rate


Version


8 kbps - 320 kbps, VBR


WMA7, WMA8, WMA9


WMA


Sampling frequency


32 kHz - 48 kHz


Bit rate


48 kbps - 192 kbps, VBR


Tag information (Song title and Artist name)


Folder levels


ID3 tag VER1.0, VER1.1, VER2.2, VER2.3 (MP3
only)


Folder levels: 8, Folders: 255 (including root folder), Files: 512 (Max. 255 files for one folder)


Text character number limitation


128 characters


Displayable character codes*2


01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE (UTF-16
Non-BOM Big Endian), 05: UNICODE (UTF-8), 06: UNICODE (Non-UTF-16 BOM Little Endian)


*1 Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be


played.


*2 Available codes depend on what kind of media, versions and information are going to be displayed.


Display screen, heater, air conditioner and audio systems 4-17


墌 05.10.18/Z33-D/V5.0 墍


Troubleshooting guide:


Symptom


Cannot play


Poor sound quality


It takes a relatively long time be- fore the music starts playing.


Music cuts off or skips


Skipping with high bit rate files Move immediately to the next song when playing. The songs do not play back in the desired order.


Cause and Countermeasure


Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player. If there is a temperature increase error, the CD player will play correctly after it returns to the normal temperature. If there is a mixture of music CD files (CD-DA data) and MP3/WMA files on a CD, only the music CD files (CD-DA data) will be played. Files with extensions other than “.MP3”, “.WMA”, “.mp3” or “.wma” cannot be played. In addition, the character codes and num- ber of characters for folder names and file names should be in compliance with the specifications. Check if the disc or the file is generated in an irregular format. This may occur depending on the variation or the setting of MP3/WMA writing applications or other text editing applications. Check if the finalization process, such as session close and disc close, is done for the disc. Check if the disc is protected by copyright. Check if the disc is scratched or dirty. Bit rate may be too low. If there are many folder or file levels on the MP3/WMA disc, or if it is a multisession disc, some time may be required before the music starts playing. The writing software and hardware combination might not match, or the writing speed, writing depth, writing width, etc., might not match the specifications. Try using the slowest writing speed. Skipping may occur with large quantities of data, such as for high bit rate data. When a non-MP3/WMA file has been given an extension of “.MP3”, “.WMA”, “.mp3” or “.wma”, or when play is prohibited by copyright protection, there will be approximately 5 seconds of no sound and then the player will skip to the next song. The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.


4-18 Display screen, heater, air conditioner and audio systems


墌 05.10.18/Z33-D/V5.0 墍


8. RPT (Repeat) play button 9. CD EJECT button 10. TUNE/FF⋅REW button 11. ON⋅OFF/VOL (Volume) control knob 12. Audio/Clock display 13. Station and preset select button 14. AUDIO button Audio main operation ON⋅OFF/Volume control: Turn the ignition key to ACC or ON, and then push the ON⋅OFF/VOL (Volume) control knob while the system is off to call up the mode (radio or CD) which was playing immediately before the system was turned off. When no CD is loaded, the radio will come on. While the system is on, pushing the ON⋅OFF/VOL control knob turns the system off. Turn the ON⋅OFF/VOL control knob to adjust the volume. AUDIO button (BASS, TREBLE, FADER, BALANCE): Press the AUDIO button to change the selecting mode as follows. BASS → TREBLE → FADE → BALANCE To adjust Bass, Treble, Fader and Balance, push Display screen, heater, air conditioner and audio systems 4-19


SAA1298


3. DISP (Display) CHANGE button 4. SCAN tuning button 5. CD play button 6. RADIO (FM/AM) band select button 7. MIX play button


墌 05.10.18/Z33-D/V5.0 墍


FM-AM RADIO WITH COMPACT DISC (CD) PLAYER 1. MUTE button 2. SEEK/APS REW, APS FF/TRACK


CHANGE button


the


the


in


) or SEEK (


display. Push


the desired mode the AUDIO button until (BASS, TREBLE, FADER or BALANCE) ap- TUNE pears ) button to adjust Bass and Treble to the desired level. Use the TUNE or SEEK button also to adjust Fader or Balance modes. Fader adjusts the sound level between the front and rear speakers and Balance adjusts the sound between the right and left speakers. the radio or CD display After 10 seconds, reappears. Once the sound quality is set to the desired level, push the AUDIO button repeatedly until the radio or CD display appears.


MUTE button:


Push the MUTE button to mute the audio sound. Push the MUTE button again to release the mute. DISP DISPLAY CHANGE: Push the DISP button for more than 1.5 seconds to adjust the digital clock display. See “Clock” in the “2. Instruments and controls” section for the clock adjustment operation. When the DISP button is pushed for less than 1.5 seconds while the compact disc is being played, the display will show the CD play time.


FM-AM radio operation


RADIO (FM/AM) band select:


Pushing the RADIO band select button will change the band as follows: AM → FM1 → FM2 → AM When RADIO band select button is pushed while the ignition switch is in the ACC or ON, the radio will come on at the station last played.


The last station played will also come on when the power knob is turned to ON.


If a compact disc is playing when the RADIO band select button is pushed, the compact disc will automatically be turned off and the last radio station played will come on. The FM stereo indicator ST will glow during FM stereo reception. When the stereo broadcast signal the radio will automatically change from stereo to monaural reception.


is weak,


TUNE (Tuning):


WARNING


The radio should not be tuned while


driving so full attention may be given to vehicle operation.


or


Push the TUNE button for manual tuning. To move quickly through the channels, push and hold either side of the TUNE button down for more than 0.5 seconds. SEEK tuning:


to tune Push the SEEK button from high to low or low to high frequencies and stops at the next broadcasting station.


or


SCAN tuning:


Push the SCAN tuning button to tune from low to high frequencies and stops at each broad- casting station for 5 seconds. Pushing the but- ton again during this 5 second period will stop SCAN tuning and the radio will remain tuned to that station.


If the SCAN tuning button is not pushed within 5
seconds, SCAN tuning moves to the next sta- tion. Station memory operations:


Twelve stations can be set for the FM band (six for FM1, six for FM2) and six stations can be set for the AM band.


4-20 Display screen, heater, air conditioner and audio systems


墌 05.10.18/Z33-D/V5.0 墍


1. Tune to the desired station using the SEEK,


SCAN or TUNE button.


2. Select the desired station and keep pushing any of the desired station select buttons (1 to 6) until a beep sound is heard. (The radio mutes when the select button is pushed.)


3. The channel indicator will then come on and the sound will resume. Memorizing is now complete.


4. Other buttons can be set in the same manner. If the battery cable is disconnected, or if the fuse blows, the radio memory will be erased. In that case, reset the desired sta- tions. Compact disc (CD) player operation Turn the ignition key to the ACC or ON position and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start play- ing. After loading the disc, the number of tracks on the disc will appear on the display. If the radio is already operating, it will automati- cally turn off and the compact disc will play.


CAUTION


Do not force the compact disc into the slot. This could damage the player.


If the system has been turned off while the compact disc was playing, pushing the ON⋅OFF/VOL control knob will start the com- pact disc.


3.1 in (8 cm) diameter compact discs can also be used without an adapter.


CD PLAY:


When the CD (CD play) button is pushed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play.


When the CD button is pushed with the com- pact disc loaded but the radio playing, the radio will automatically be turned off and the compact disc will start to play. DISP CD PLAY TIME:


Push the DISP button for less than 1.5 seconds while the compact disc is being played to show the play time on the display.


FF (Fast Forward), REW (Rewind):


(fast forward) or


(rewind) When the button is pushed while the compact disc is being played, the compact disc will play while fast forwarding or rewinding. When the button is released, the compact disc will return to normal play speed.


APS (Automatic Program Search) FF, APS REW/ TRACK CHANGE:


(APS FF) button is pushed When the while the compact disc is being played, the program next to the present one will start to play from its beginning. Push several times to skip through programs. The compact disc will ad- vance the number of times the button is pushed. (When the last program on the compact disc is skipped through, the first program will be (APS REW) button is played.) When the pushed, the program being played returns to its beginning. Push several times to skip back through programs. The compact disc will go back the number of times the button is pushed.


SCAN tuning:


When the SCAN tuning button is pushed while the CD is being played, the beginning of all the


Display screen, heater, air conditioner and audio systems 4-21


墌 05.10.18/Z33-D/V5.0 墍


tracks of CD will be played for 10 seconds in sequence. Pushing the button again during this 10 second period will stop SCAN tuning. the SCAN tuning button is not pushed within 10 seconds, SCAN tuning moves to the next CD program.


If


MIX MIX play:


When the MIX button is pushed while the com- pact disc is being played, programs will be played at random, not following the sequence on the compact disc. The same program may be repeated twice. Push the MIX button again to return to the normal play mode. REPEAT (RPT) play:


When the RPT button is pushed while the compact disc is being played, the play pattern can be changed as follows:


The display shows the following symbol; (no mark): 1 CD RPT (Repeat) 1: 1 TR (Track) RPT


CD EJECT:


When the CD EJECT button is pushed with the compact disc loaded, the compact disc will be ejected. When this button is pushed while the compact disc is being played, the compact disc will come out and the system will turn off. If the compact disc comes out and is not removed, it will be pulled back into the slot to protect it. (except for 3.1 in [8 cm] diam- eter compact discs) If the following message appears on the display, push the EJECT button: 쐌 CHECK DISC — Eject the disc, and check whether it is damaged or inserted upside-down.


쐌 CD ERR F * — Eject the disc, and check whether it is a proper audio CD. (* shows a different number according to the au- dio condition.)


CD IN indicator: CD IN indicator appears on the display when the CD is loaded.


4-22 Display screen, heater, air conditioner and audio systems


墌 05.10.18/Z33-D/V5.0 墍


8. RPT (Repeat) play/CLOCK button 9. CD EJECT button 10. TUNE/FF⋅REW button 11. ON⋅OFF/VOL (Volume) control knob 12. Audio/Clock display 13. Station and preset (FM/AM/SAT*)/CD in-


sert or CD play select button


14. AUDIO button * No satellite radio reception is available when the SAT band option is selected unless op- tional satellite receiver and antenna are in- stalled, and an XM® or SIRIUSTM satellite radio service subscription is active.


It may take some time to receive the activation signal after subscribing to the XM or SIRI- USTM satellite radio provider. After receiving the activation signal, an available channel list will be automatically updated in the radio. For XM , turn the ignition switch from the LOCK to ACC position to update the channel list.


Satellite radio is not available in Alaska and Hawaii. Audio main operation Head unit:


The auto loudness circuit enhances the low frequency range automatically in both radio re- ception and CD playback.


FM-AM-SAT RADIO WITH COMPACT DISC (CD) CHANGER 1. CD LOAD button 2. SEEK/APS REW, APS FF/TRACK


CHANGE button


SAA1299


3. DISP (Display) CHANGE button 4. SCAN tuning button 5. CD PLAY button 6. RADIO (FM/AM/SAT*) band select button 7. PTY (Program type), CAT (Category)* select


button


Display screen, heater, air conditioner and audio systems 4-23


墌 05.10.18/Z33-D/V5.0 墍


This audio system has an active noise compen- sation feature called “Audio Pilot”. The Audio Pilot uses a microphone to detect external road noise and automatically adjusts the amplifier to compensate for any competing high, midrange, or low frequency noise. ON⋅OFF/Volume control: Turn the ignition key to ACC or ON, and then push the ON⋅OFF/VOL (Volume) control knob while the system is off to call up the mode (radio or CD) which was playing immediately before the system was turned off. When no CD is loaded, the radio will come on. While the system is on, pushing the ON⋅OFF/VOL control knob turns the system off. Turn the ON⋅OFF/VOL control knob to adjust the volume. AUDIO button: Push the AUDIO button to change the selecting mode as follows. BASS → TREBLE → FADE → BALANCE → AUDIOP To adjust Bass, Treble, Fader and Balance, push the AUDIO button until the desired mode (BASS, TREBLE, FADER or BALANCE) ap- TUNE pears ) button 4-24 Display screen, heater, air conditioner and audio systems


display. Push


) or SEEK (


the


the


in


to adjust Bass and Treble to the desired level. Use the TUNE or SEEK button also to adjust Fader or Balance modes. Fader adjusts the sound level between the front and rear speakers and Balance adjusts the sound between the right and left speakers. To change the AUDIOP (Audio Pilot) mode to OFF or ON, push the TUNE or SEEK button. Once you have adjusted the sound quality to the desired level, push the AUDIO button repeatedly until the radio or CD display reappears. Other- wise, the radio or CD display will automatically reappear after about 10 seconds.


CLOCK adjusting:


Push the RPT button for more than 1.5 seconds to adjust the digital clock display. When the clock adjusting display is selected, the time (hour or minute) will start flashing. See “Clock” in the “2. Instruments and controls” section for the detailed clock adjustment opera- tion. DISP DISPLAY CHANGE: This button will work during satellite radio (if so equipped) and CD operation. Find the detailed function in the description of each item.


FM-AM-SAT radio operation


RADIO (FM/AM/SAT) band select:


Pushing the RADIO band select button will change the band as follows:


(Without satellite radio) AM → FM1 → FM2 → AM (With satellite radio) AM → FM1 → FM2 → SAT1 → SAT2 → AM No satellite operation is available during scrolling of modes, unless optional satellite receiver and antenna are installed, and an XM or SIRIUSTM satellite radio service subscription is active. When RADIO band select button is pushed while the ignition switch is in the ACC or ON, the radio will come on at the station last played. The last station/channel played will also come on when the ON⋅OFF/VOL control knob is pushed to ON. If a compact disc is playing when the RADIO band select button is turned to ON, the compact disc will automatically be turned off and the last radio station/channel played will come on. The FM stereo indicator ST will glow during FM stereo reception. When the stereo broadcast signal the radio will automatically


is weak,


墌 05.10.18/Z33-D/V5.0 墍


change from stereo to monaural reception.


channels of the next or previous category.


1. Tune to the desired station/channel using the


If the satellite radio signal is lost due to interfer- ence while driving, in a parking structure or tunnel for example, “NO SIGNAL” will be dis- played and no satellite radio station will be available.


TUNE (Tuning):


WARNING


The radio should not be tuned while driving so full attention may be given to vehicle operation.


or


for manual Push the TUNE button tuning. To move quickly through the channels, push and hold either side of the TUNE button down for more than 0.5 seconds. SEEK tuning:


(For FM and AM radio) to tune Push the SEEK button from high to low or low to high frequencies and stops at the next broadcasting station. (For satellite radio) Push the SEEK button


to seek


or


or


SCAN tuning:


Push the SCAN tuning button to tune from low to high frequencies and stops at each broad- casting station for 5 seconds. Pushing the but- ton again during this 5 second period will stop SCAN tuning and the radio will remain tuned to that station.


If the SCAN tuning button is not pushed within 5
seconds, SCAN tuning moves to the next sta- tion. DISP SAT radio display change (if so


equipped):


쐌 Pushing the DISP button will display addi- information (for example: Title, Artist


tional name) about the satellite radio broadcast.


쐌 Pushing the DISP button for more than 1.5
seconds will change the display mode as follows: Channel number → Channel name → Artist name → Song title → Channel number


Station memory operations: Twelve stations/channels can be set for the FM band (6 for FM1, 6 for FM2) and the SAT radio (6 for SAT1, 6 for SAT2), and 6 stations can be set for the AM band.


SEEK, SCAN or TUNE button.


2. Select the desired station/channel and keep pushing any of the desired station/channel and preset buttons (1 to 6) until a beep sound is heard. (The radio mutes when the station and preset button is pushed.)


3. The channel indicator will then come on and the sound will resume. Memorizing is now complete.


4. Other buttons can be set in the same manner. If the battery cable is disconnected, or if the fuse blows, the radio memory will be erased. In that case, reset the desired sta- tions. Radio data system (RDS): RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band) and/or SAT encoded within a regular radio broadcast. Currently, most RDS stations are in large cities, but many stations are now consid- ering broadcasting RDS data. RDS can display: 쐌 Station call sign, such as “WHFR 98.3”. 쐌 Station name, such as “The Groove”.


Display screen, heater, air conditioner and audio systems 4-25


墌 05.10.18/Z33-D/V5.0 墍


쐌 Music or programming type such as “Classi-


mode will be cancelled.


PTY (CAT) name selection can also be achieved by pushing the preset buttons.


Initial PTY (CAT) names are stored in the preset buttons, but these can be changed by pushing the preset buttons for more than 1.5
seconds when the desired PTY (CAT) name is in the display.


cal”, “Country”, or “Rock”.


쐌 Traffic reports about delays or construction. If the station broadcasts RDS information, the RDS icon is displayed.


Program type (PTY)/Category (CAT) select:


When PTY button is pushed during FM mode, the PTY (CAT) name of the current tuned station is displayed. When the PTY (CAT) button is pushed during satellite radio mode (if so equipped), the category name of the current channel is displayed. During this time if the PTY data code is zero, or the data is unreadable, the display will show “NONE”. 1. PTY (CAT) selection mode


or


PTY (CAT) name selection can be done by the up/down TUNE button in the PTY (CAT) selection mode. It is possible to shift the PTY (CAT) name by one step, with one push of the up/down TUNE button After selecting a PTY (CAT) name, push the SEEK button or SCAN button within 10
seconds. Tuning to the PTY (CAT) station will start. If you do not push the TUNE button within the 10 second period, the PTY (CAT)


or


After selecting a PTY (CAT) name, push the within 10 sec- SEEK button 4-26 Display screen, heater, air conditioner and audio systems


or


2. PTY (CAT) SEEK tuning mode


onds. Tuning to the PTY (CAT) station will start. If you do not push the SEEK button within the 10 second period, the PTY (CAT) mode will be cancelled.


3. PTY (CAT) SCAN tuning mode


Push the SCAN tuning button to tune the PTY (CAT) name station, and stop at each broadcasting station for 5 seconds. Pushing the button again during this 5 second period will stop SCAN tuning and the radio will remain tuned to that station. If the SCAN tuning button is not pushed within 5 seconds, SCAN tuning moves to the next station.


Compact disc (CD) changer operation Turn the ignition key to the ACC or ON position, push the LOAD button and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start playing. After loading the disc, the number of tracks on the disc will appear on the display. If the radio is already operating, it will automati- cally turn off and the compact disc will play.


墌 05.10.18/Z33-D/V5.0 墍


CAUTION


쐌 Do not force the compact disc into the slot. This could damage the player.


쐌 Do not use 3.1 in (8 cm) discs.


If the system has been turned off while the compact disc was playing, pushing the ON⋅OFF/VOL control knob will start the com- pact disc.


When the button is pushed with the com- pact disc loaded but the tape or the radio playing, the tape or radio will automatically be turned off and the compact disc will start to play. DISP CD PLAY INFORMATION:


When the DISP button is pushed for less than 1.5 seconds while the compact disc is being played, the play time will be displayed.


When the DISP button is pushed for more than 1.5 seconds while the CD is being played, the disc information display will change.


CD LOAD:


CD:


To insert a CD in the CD changer, push the LOAD button for less than 1.5 seconds. Select the loading slot by pushing the CD insert select button (1 to 6), then insert the CD. To insert 6 CDs to the CD changer in succes- sion, push the LOAD button for more than 1.5
seconds. The inserted slot numbers will illuminate on the display.


CD with MP3 or WMA:


FF (Fast Forward), REW (Rewind):


CD PLAY:


CD:


(CD play) button is pushed with When the the system off and the compact disc loaded, the system will turn on and the compact disc will start to play.


(fast forward) or


(rewind) When the button is pushed while the compact disc is being played, the compact disc will play while fast forwarding or rewinding. When the button is


or


released, the compact disc will return to normal play speed. CD with MP3 or WMA: When the button is pushed for less than 1.5 seconds while the compact disc is being played, the folders in the compact disc will change. When the button is pushed for more than 1.5 seconds while the compact disc is being played, the compact disc will play while forwarding or rewinding. When the button is released, the compact disc will return to the normal play speed.


or


APS (Automatic Program Search) FF, APS REW: When the (APS FF) button is pushed while the compact disc is being played, the program next to the present one will start to play from its beginning. Push several times to skip through programs. The compact disc will ad- vance the number of times the button is pushed. (When the last program on the compact disc is the first program will be skipped through, played.) When the (APS REW) button is pushed, the program being played returns to its beginning. Push several times to skip back through programs. The compact disc will go back the number of times the button is pushed.


Display screen, heater, air conditioner and audio systems 4-27


墌 05.10.18/Z33-D/V5.0 墍


CD PLAY select button:


CD with MP3 or WMA:


To change CD, push the CD play select button (1 to 6).


SCAN tuning:


When the SCAN tuning button is pushed for less than 1.5 seconds while the CD is being played, the beginning of all the tracks of CDs will be played for 10 seconds in sequence.


When the SCAN tuning button is pushed for more than 1.5 seconds while the CD is being played, the first program in all the CDs will be played for 10 seconds.


Pushing the button again during this 10 second period will stop SCAN tuning.


If the SCAN tuning button is not pushed within 10 seconds, SCAN tuning moves to the next disc program.


REPEAT (RPT):


When the RPT play button is pushed while the compact disc is played, the play pattern can be changed. CD:


The display shows the following symbols.


(no mark): ALL CD RPT (Repeat) 1 DISC: 1 CD RPT 1: 1 TR (Track) RPT or 1 FLDR (Folder) RPT MIX: ALL CD MIX 1 DISC MIX: 1 CD MIX 1 MIX: 1 FLDR MIX


CD EJECT:


When the CD EJECT button is pushed with the compact disc loaded, the compact disc will be ejected. To eject the discs selected by the CD select button, push the EJECT button for less than 1.5
seconds. To eject all the discs in succession, push the EJECT button for more than 1.5 seconds. When this button is pushed while the compact disc is being played, the compact disc will come out and the system will turn off. If the compact disc comes out and is not


4-28 Display screen, heater, air conditioner and audio systems


removed, it will be pulled back into the slot to protect it. If either of the following messages appear on the display, push the EJECT button: 쐌 PUSH EJECT — Eject the disc, and insert it


again.


쐌 CHECK DISC — Eject the disc, and check whether it is damaged or inserted upside-down.


쐌 CD ERR F * — Eject the disc, and check whether it is a proper audio CD. (* shows a different number according to the au- dio condition.)


CD IN indicator: CD IN indicator (inserted slot number 1 - 6) appears on the display when the CD is loaded.


墌 05.10.18/Z33-D/V5.0 墍


MODE select switch Push the MODE select switch to change the mode.


Without satellite radio:


AM, FM1, FM2 and CD or CD changer


With satellite radio:


AM, FM1, FM2, SAT1, SAT2 and CD changer VOLUME control switches Push up or down the VOLUME control switch to increase or decrease the volume.


Tuning switch


SAA0451


SAA1300


CD CARE AND CLEANING 쐌 Handle a CD by its edges. Never touch the


surface of the disc. Do not bend the disc.


쐌 Always place the discs in the storage case


when they are not being used.


쐌 To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion. Do not use a conventional record cleaner or alcohol intended for industrial use.


쐌 A new disc may be rough on its inner and outer edges. Remove the rough edges using the side of a pen or pencil as illustrated.


1. VOLUME control switch 2. MODE select switch 3. POWER on/off switch 4. Tuning switch STEERING WHEEL SWITCH FOR AUDIO CONTROL (if so equipped) The audio system can be operated using the controls on the steering wheel. POWER on/off switch With the ignition switch turned to the ACC or ON position, push the POWER on/off switch to turn the audio system on or off.


Memory change (radio): Push up or down the tuning switch for less than 1.5 seconds to change the radio frequency. SEEK tuning (radio): Push up or down the tuning switch for more than 1.5 seconds to seek the next or previous radio station. APS (Automatic Program Search) FF, APS REW (CD or CD changer): Push up or down the tuning switch for less than 1.5 seconds to return to the beginning of the present program or skip to the next program. Display screen, heater, air conditioner and audio systems 4-29


墌 05.10.18/Z33-D/V5.0 墍


Push several times to skip back or skip through programs. This system searches for the blank intervals between selections. If there is a blank interval within one program or there is no interval be- tween programs, the system may not stop in the desired or expected location. FOLDER change (CD changer/CD with MP3 or WMA): Push up or down the tuning switch for more than 1.5 seconds to change the folders (if there are any folders). DISC change (CD changer/CD without MP3 or WMA): Push up or down the tuning switch for more than 1.5 seconds to change the playing disc up or down.


CAR PHONE OR CB RADIO


When installing a CB, ham radio or car phone in your NISSAN vehicle, be sure to observe the following cautions, otherwise the new equip- ment may adversely affect the Engine Control system and other electronic parts.


WARNING


쐌 A cellular telephone should not be used while driving so full attention may be given to vehicle operation. Some jurisdictions prohibit the use of cellular telephones while driving. 쐌 If you must make a call while your vehicle is in motion, the hands free cellular phone operational mode (if so equipped) is highly recommended. Exercise extreme caution at all times so full attention may be given to vehicle operation.


쐌 If a conversation in a moving vehicle requires you to take notes, pull off the road to a safe location and stop your vehicle before doing so.


SAA0606


ANTENNA The antenna is located at the rear of the vehicle. To remove the antenna, turn it counterclockwise. To reinstall it, screw it securely into the base.


CAUTION


Be sure to remove the antenna before entering a low-roof garage or an auto- matic car wash. Otherwise the antenna may be damaged.


4-30 Display screen, heater, air conditioner and audio systems


墌 05.10.18/Z33-D/V5.0 墍


CAUTION


쐌 Keep the antenna as far away as possible from the electronic control modules.


쐌 Keep the antenna wire more than 8 in (20 cm) away from the electronic con- trol system harnesses. Do not route the antenna wire next to any harness.


쐌 Adjust


the antenna standing-wave ratio as recommended by the manu- facturer.


쐌 Connect the ground wire from the CB


radio chassis to the body.


쐌 For details, consult a NISSAN dealer.


Display screen, heater, air conditioner and audio systems 4-31


墌 05.10.18/Z33-D/V5.0 墍


MEMO


4-32 Display screen, heater, air conditioner and audio systems


墌 05.10.18/Z33-D/V5.0 墍


5 Starting and driving


Precautions when starting and driving ............................ 5-2
Exhaust gas (Carbon monoxide) ................................. 5-2
Three way catalyst .......................................................... 5-3
Tire pressure monitoring system (TPMS) ................. 5-3
Avoiding collision and rollover ..................................... 5-5
Drinking alcohol/drugs and driving ............................ 5-5
Ignition switch ....................................................................... 5-6
Automatic transmission ................................................. 5-6
Manual transmission ....................................................... 5-7
Key positions ................................................................... 5-7
NISSAN vehicle immobilizer system .......................... 5-8
Before starting the engine ................................................. 5-8
Starting the engine ............................................................... 5-9
Driving the vehicle ................................................................ 5-9
Automatic transmission ................................................. 5-9
Manual transmission .................................................... 5-13
Parking brake ...................................................................... 5-15
Cruise control (if so equipped) ...................................... 5-16
Precautions on cruise control ................................... 5-16
Cruise control operations ........................................... 5-16


Break-in schedule .............................................................. 5-18
Increasing fuel economy .................................................. 5-18
Parking/parking on hills .................................................... 5-19
Power steering .................................................................... 5-20
Brake system ....................................................................... 5-20
Braking precautions ..................................................... 5-20
Anti-lock brake system (ABS) .................................. 5-21
Traction control system (TCS) (if so equipped) ........ 5-22
Vehicle dynamic control (VDC) system (if so equipped) .................................................................. 5-23
Cold weather driving ......................................................... 5-25
Freeing a frozen door lock ......................................... 5-25
Anti-freeze ...................................................................... 5-25
Battery ............................................................................. 5-25
Draining of coolant water ........................................... 5-25
Tire equipment .............................................................. 5-25
Special winter equipment .......................................... 5-26
Driving on snow or ice ................................................ 5-26
Engine block heater (if so equipped) ..................... 5-26


墌 05.10.18/Z33-D/V5.0 墍


PRECAUTIONS WHEN STARTING AND DRIVING


WARNING


prevent children’s access to car keys. (Roadster models)


쐌 Do not leave children or adults who would normally require the support of others alone in your vehicle. Pets should not be left alone either. They could accidentally injure themselves or others through inadvertent opera- tion of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.


쐌 Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury. (Coupe models)


쐌 Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured. Keep the car locked with the trunk closed when not in use, and


5-2 Starting and driving


senger compartment. If you must drive with the rear hatch/trunk lid open, follow these precautions:


EXHAUST GAS (Carbon monoxide)


1. Open all the windows.


WARNING


Do not breathe exhaust gases; they con- tain colorless and odorless carbon mon- oxide. Carbon monoxide is dangerous. It can cause unconsciousness or death. 쐌 If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately.


쐌 Do not run the engine in closed


spaces such as a garage.


쐌 Do not park the vehicle with the en- gine running for any extended length of time.


쐌 Keep the rear hatch/trunk lid closed while driving, otherwise exhaust gases could be drawn into the pas-


2. Set the air recirculation mode OFF and the fan control at the maxi- mum position to circulate the air. 쐌 If electrical wiring or other cable con- nections must pass to a trailer through the seal on the rear hatch/trunk lid or the body, follow the manufacturer’s recommendation to prevent carbon monoxide entry into the vehicle.


쐌 If a special body, camper, or other equipment is added for recreational or other usage, follow the manufac- turer’s recommendation to prevent carbon monoxide entry into the ve- hicle. Some recreational vehicle ap- pliances such as stoves, refrigera- tors, heaters, etc. may also generate carbon monoxide.


墌 05.10.18/Z33-D/V5.0 墍


쐌 The exhaust system and body should be inspected by a qualified mechanic whenever: • The vehicle is raised for service. • You suspect that exhaust fumes are entering into the passenger compartment.


• You notice a change in the sound


of the exhaust system.


• You have had an accident involv- ing damage to the exhaust system, underbody, or rear of the vehicle.


THREE WAY CATALYST The three way catalyst is an emission control device installed in the exhaust system. Exhaust gases in the converter are burned at high tem- peratures to help reduce pollutants.


WARNING


쐌 The exhaust gas and the exhaust sys- tem are very hot. Keep people, ani-


mals or flammable materials away from the exhaust system compo- nents.


쐌 Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.


CAUTION


쐌 Do not use leaded gasoline. Deposits from leaded gasoline will seriously reduce the three-way catalyst’s abil- ity to help reduce exhaust pollutants. 쐌 Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat. Do not keep driving if the engine misfires, or if noticeable loss of performance or other unusual operating conditions are detected. Have the vehicle in- spected promptly by a NISSAN dealer.


쐌 Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damag- ing the three-way catalyst.


쐌 Do not race the engine while warm-


ing it up.


쐌 Do not push or tow your vehicle to


start the engine.


TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle plac- ard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire infla- tion pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pres- sure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as Starting and driving 5-3


墌 05.10.18/Z33-D/V5.0 墍


possible, and inflate them to the proper pres- sure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel effi- ciency and tire tread life, and may affect the vehicle’s handling and stopping ability.


illumination of


Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level

Loading...
x